Film capacitors MKP 2 pin capacitors, RoHS compatible Series/Type: Ordering code: B32672...3Z Date: Version: 2007-08-16 1 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 (header 1 + top left header bar): Film capacitors Identification/Classification 2 (header 2 + bottom left header bar): MKP 2 pin capacitors, RoHS compatible Ordering code: (top right header bar) Series/Type: (top right header bar) B32672...3Z Preliminary data (optional): (if necessary) Department: FK PM Date: 2007-08-16 Version: 1 (c) EPCOS AG 2007. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited Film capacitors MKP 2 pin capacitors, RoHS compatible B32672...3Z Climatic Max. operating temperature: 110 C Climatic category (IEC 60068-1) 55/110/56 Construction Dielectric: metallized polypropylene (PP) Wound capacitor technology Plastic case (UL 94 V-0) Epoxy resin sealing, flame retardant Terminals Od1 = 0.8 mm Parallel wire leads, lead-free tinned Dimensions in mm Marking Manufacturer's logo Rated capacitance Tolerance Rated DC voltage Type number Ordering codes and packing units Lead VR VRMS CR spacing mm V DC V AC F 15 450 220 Max. dimensions wxhxl mm Ordering code (composition see below) dv/dt K0 2 V/s V /s Ammo Reel Untaped pack pcs/unit pcs/unit pcs/unit 0.10 5.0 x 10.5 x 18.0 B32672Z4104+*** 160 128000 1000 1700 1000 0.15 5.0 x 10.5 x 18.0 B32672Z4154+*** 160 128000 1000 1700 1000 0.22 6.0 x 11.0 x 18.0 B32672Z4224+*** 160 128000 830 1300 1000 0.33 7.0 x 12.5 x 18.0 B32672Z4334+*** 160 128000 830 1300 1000 0.47 8.0 x 14.0 x 18.0 B32672Z4474+*** 160 128000 680 1100 1000 0.47 13.0 x 14.0 x 18.0 B32672T4474+*** 160 128000 680 1100 1000 0.68 9.0 x 17.5 x 18.0 128000 680 1100 1000 0.68 13.0 x 14.0 x 18.0 B32672T4684+*** 160 128000 - 500 300 1.00 11.0 x 18.5 x 18.0 B32672Z4105+*** 160 128000 - 550 250 B32672Z4684+*** 160 Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code K = 10% J = 5% (closer tolerances on request) *** = Packing code 289 = Ammo pack 189 = Reel pack 000 = Untaped (lead length 6 - 1 mm) FK PM Please read Cautions and warnings and Important notes at the end of this document. 2007-08-16 Page 2 of 7 Film capacitors MKP 2 pin capacitors, RoHS compatible Lead VRMS CR VR spacing V DC V AC F mm 15 520 630 22.5 450 520 277 310 220 277 Max. dimensions wxhxl mm B32672...3Z Ordering code (composition see below) dv/dt K0 2 V/s V /s Ammo Reel Untaped pack pcs/unit pcs/unit pcs/unit 0,047 5.0 x 10.5 x 18.0 B32672Z5473+*** 200 208000 960 1100 1000 0.10 6.0 x 11.0 x 18.0 B32672Z5104+*** 200 208000 830 900 1000 0.15 6.0 x 11.0 x 18.0 B32672Z5154+*** 200 208000 680 700 500 0.22 7.0 x 12.5 x 18.0 B32672Z5224+*** 200 208000 680 700 500 0.33 8.5 x 14.5 x 18.0 B32672Z5334+*** 200 208000 640 700 500 0.33 13.0 x 14.0 x 18.0 B32672T5334+*** 200 208000 - 500 300 0.47 9.0 x 17.5 x 18.0 B32672Z5474+*** 200 208000 640 700 500 0.47 13.0 x 14.0 x 18.0 B32672T5474+*** 200 208000 - 500 300 0.68 11.0 x 18.5 x 18.0 B32672Z5684+*** 200 208000 - 550 250 0.068 6.0 x 11.0 x 18.0 B32672Z6683+*** 250 315000 680 700 500 0.10 7.0 x 12.5 x 18.0 B32672Z6104+*** 250 315000 680 700 500 0.22 8.5 x 14.5 x 18.0 B32672Z6224+*** 250 315000 640 700 500 0.22 6.0 x 15.0 x 26.5 B32673Z4224+*** 100 80000 680 700 720 0.22 7.5 x 14.0 x 26.5 B32673T4224+*** 100 80000 550 500 570 0.33 6.0 x 15.0 x 26.5 B32673Z4334+*** 100 80000 680 700 720 0.33 7.5 x 14.0 x 26.5 B32673T4334+*** 100 80000 550 500 570 0.47 6.0 x 15.0 x 26.5 B32673Z4474+*** 100 80000 680 700 720 0.47 7.5 x 14.0 x 26.5 B32673T4474+*** 100 80000 550 500 570 0.68 7.0 x 16.0 x 26.5 B32673Z4684+*** 100 80000 580 600 630 0.68 7.5 x 14.0 x 26.5 B32673T4684+*** 100 80000 550 500 570 1.00 10.5 x 16.5 x 26.5 B32673Z4105+*** 100 80000 390 400 540 1.50 11.0 x 20.5 x 26.5 B32673Z4155+*** 100 80000 370 350 510 2.20 12.0 x 22.0 x 26.5 B32673Z4225+*** 100 80000 - - 450 0.22 6.0 x 15.0 x 26.5 B32673Z5224+*** 120 125000 680 700 720 0.22 7.5 x 14.0 x 26.5 B32673T5224+*** 120 125000 550 500 570 0.33 6.0 x 15.0 x 26.5 B32673Z5334+*** 120 125000 680 700 720 0.33 7.5 x 14.0 x 26.5 B32673T5334+*** 120 125000 550 500 570 0.47 7.0 x 16.0 x 26.5 B32673Z5474+*** 120 125000 580 600 630 0.47 7.5 x 14.0 x 26.5 B32673T5474+*** 120 125000 550 500 570 0.68 10.5 x 16.5 x 26.5 B32673Z5684+*** 120 125000 390 400 540 1.00 10.5 x 20.5 x 26.5 B32673Z5105+*** 120 125000 390 400 540 1.50 12.0 x 22.0 x 26.0 B32673Z5155+*** 120 125000 - - 450 Further E series and intermediate capacitance values on request. Composition of ordering code see page 2 FK PM Please read Cautions and warnings and Important notes at the end of this document. 2007-08-16 Page 3 of 7 Film capacitors MKP 2 pin capacitors, RoHS compatible B32672...3Z Technical data Maximum operating temperature Top,max Dissipation factor tan (in 10-3 ) at 20 C (upper limit values) Insulation resistance Ris or time constant = CR Ris at 20 C, rel. humidity 65% +110 C at 1 kHz 100 kHz CR 0.1 F 0.1 F<CR 1.0 1.0 5 - 30 000 M (minimum as-delivered values) DC test voltage Passive flammability category In accordance with IEC 40 (CO) 752 Maximum continuous AC voltage (VAC ) Surge pulse test IEC 1000-4-5 1.6 x VR, 2 s C 220 V / 277 V / 310 V (50/60 Hz) 1.2 s / 50 s / 1200 V 8.0 s / 20 s / 1200 V 56 days / 40 C / 93% relative humidity Capacitance change (C/ C) 5% Damp heat test Dissipation factor change (tan 0.5 *10-3 (at 1 kHz) Limit values after damp heat test Insulation resistance Ris 1,0 *10-3 (at 10 kHz) or time constant = CR Ris 50% of minimum as-delivered values Pulse handling capability "dv/dt" values represent the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/s. "K0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/s. Note: The maximum values of dv/dt and K0 must not be exceeded in order to avoid damaging the capacitor. FK PM Please read Cautions and warnings and Important notes at the end of this document. 2007-08-16 Page 4 of 7 Film capacitors MKP 2 pin capacitors, RoHS compatible B32672...3Z Cautions and warnings General notes on soldering Permissible heat-exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus irreversibly change a capacitor's electrical characteristics. For short exposure times (as in practical soldering processes), the heat load (and thus the possible effects on the capacitor) will also depend on other factors such as: The pre-heating temperature and time. The forced cooling immediately after soldering. The terminal characteristics: diameter, length, thermal resistance, special configurations (e.g. crimping). The height of the capacitor above the solder bath. Shadowing by neighboring components. Additional heating due to heat dissipation by neighboring components. Use of solder-resistant coatings. The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced cooling process may have to be included. Cleaning To determine whether a particular solvent, often used to remove flux residues and other substances, is suitable for the capacitors described, please refer to latest data book "Film Capacitors", in which this information is available. Even when suitable solvents are used, a reversible change of the electrical characteristics may occur in uncoated capacitors immediately after they have been washed. Thus it is always recommended to dry the components (e.g. 4 h at 70 C) before they are subjected to subsequent electrical testing. Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must be taken into account. Our experience has shown that the following potting materials can be recommended considering maximum curing temperature 100 C: Non-flexible epoxy resins with acid-anhydride hardeners Chemically inert, non-conducting fillers Storage conditions All capacitors listed in this product profile can be stored for short periods at any temperature within the entire range of category temperatures. For long storage periods, however, the following conditions should be observed: Storage temperature - 40 to +40 C Maximum relative humidity 80%, no dew allowed on the capacitor Maximum duration 24 months (12 months for taped components) FK PM Please read Cautions and warnings and Important notes at the end of this document. 2007-08-16 Page 5 of 7 Film capacitors MKP 2 pin capacitors, RoHS compatible B32672...3Z Resistance to vibration A capacitor's ability to withstand vibration (e.g. such as that occurring in applications involving rotating machinery) is tested to IEC 60068-2-6. The test procedure used here involves continuous sinusoidal vibration along three orthogonal axes, with a continuously varying frequency (10 ... 500 Hz), an acceleration amplitude of 10 g, a displacement amplitude of 0.75 mm and a duration of 360 minutes for each axis. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Passive flammability The passive flammability test is applied to ensure that components bearing the corresponding qualification contribute less energy to the combustion behavior of their immediate vicinity than is required to ignite them. This measure is designed to contain any localized fire that may occur. In the respective tests, the capacitors are subjected to a standardized flame to evaluate their combustion behavior by checking whether the flame persists for longer than a maximum permissible period or not. The severity of the test is determined essentially by the test flame and exposure time in accordance with various international standards (IEC 60040 CO 752 (amendment to IEC 60384-1), IEC 60695-22 and UL 1414). Unless the detail specifications stipulate otherwise, EMI suppression capacitors are tested to IEC 60384-14, section 4.17, test severity categories B and C. FK PM Please read Cautions and warnings and Important notes at the end of this document. 2007-08-16 Page 6 of 7 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as "hazardous"). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 7 of 7