B32672T5334J289 - EPCOS AG - Datasheet.Directory

Film capacitors

MKP 2 pin capacitors, RoHS compatible

Series/Type: B32672…3Z

Ordering code:

Date: 2007-08-16

Version: 1

contained therein without EPCOS' prior express consent is prohibited

Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the

table and then chan g e the color to "white". This ensures that the table disappears (invisible) for the customer PDF.

Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it!

Identification/Classification 1

(header 1 + top left header bar):

Film capacitors

Identification/Classification 2

(header 2 + bottom left header bar):

MKP 2 pin capacitors, RoHS compatible

Ordering code: (top right header bar)

Series/Type: (top right header bar) B32672…3Z

Preliminary data (optional):

(if necessary)

Department: FK PM

Date: 2007-08-16

Version: 1

Film capacitors

MKP 2 pin capacitors, RoHS compatible B32672…3Z

FK PM 2007-08-16

Please read Cautions and warnings and Page 2 of 7

Important notes at the end of this document.

Climatic

 Max. operating temperature: 110 °C

 Climatic category (IEC 60068-1) 55/110/56

Construction

 Dielectric: metallized polypropylene (PP)

 Wound capacitor technology

 Plastic case (UL 94 V-0)

 Epoxy resin sealing, flame retardant

Terminals

 Parallel wire leads, lead-free tinned

Marking

 Manufacturer’s logo

 Rated capacitance

 Tolerance

 Rated DC voltage

 Type number

Ød1 = 0.8 mm

Dimensions in mm

Ordering codes and packing units

Lead

spacing

mm

VR

V DC

VRMS

V AC

CR

μF

Max. dimensions

w x h x l

mm

Ordering code

(composition see

below)

dv/dt

V/μs

K0

V2/μs

Ammo

pack

pcs/unit

Reel

pcs/unit

Untaped

pcs/unit

15 450 220 0.10

0.15

0.22

0.33

0.47

0.68

1.00

5.0 x 10.5 x 18.0

6.0 x 11.0 x 18.0

7.0 x 12.5 x 18.0

8.0 x 14.0 x 18.0

13.0 x 14.0 x 18.0

9.0 x 17.5 x 18.0

13.0 x 14.0 x 18.0

11.0 x 18.5 x 18.0

B32672Z4104+***

B32672Z4154+***

B32672Z4224+***

B32672Z4334+***

B32672Z4474+***

B32672T4474+***

B32672Z4684+***

B32672T4684+***

B32672Z4105+***

160

128000

1000

830

680

-

1700

1300

1100

500

550

1000

300

250

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code *** = Packing code

K = ±10% 289 = Ammo pack

J = ±5% 189 = Reel pack

(closer tolerances on request) 000 = Untaped (lead length 6 - 1 mm)

Film capacitors

MKP 2 pin capacitors, RoHS compatible B32672…3Z

FK PM 2007-08-16

Please read Cautions and warnings and Page 3 of 7

Important notes at the end of this document.

Lead

spacing

mm

VR

V DC

VRMS

V AC

CR

μF

Max. dimensions

w x h x l

mm

Ordering code

(composition see

below)

dv/dt

V/μs

K0

V2/μs

Ammo

pack

pcs/unit

Reel

pcs/unit

Untaped

pcs/unit

520 277 0,047

0.10

0.15

0.22

0.33

0.47

0.68

5.0 x 10.5 x 18.0

6.0 x 11.0 x 18.0

7.0 x 12.5 x 18.0

8.5 x 14.5 x 18.0

13.0 x 14.0 x 18.0

9.0 x 17.5 x 18.0

13.0 x 14.0 x 18.0

11.0 x 18.5 x 18.0

B32672Z5473+***

B32672Z5104+***

B32672Z5154+***

B32672Z5224+***

B32672Z5334+***

B32672T5334+***

B32672Z5474+***

B32672T5474+***

B32672Z5684+***

200

208000

960

830

680

640

-

640

-

1100

900

700

500

700

500

550

1000

500

300

500

300

250

15

630 310 0.068

0.10

0.22

6.0 x 11.0 x 18.0

7.0 x 12.5 x 18.0

8.5 x 14.5 x 18.0

B32672Z6683+***

B32672Z6104+***

B32672Z6224+***

250

315000

680

640

700

500

450 220 0.22

0.22

0.33

0.47

0.68

1.00

1.50

2.20

6.0 x 15.0 x 26.5

7.5 x 14.0 x 26.5

6.0 x 15.0 x 26.5

7.5 x 14.0 x 26.5

6.0 x 15.0 x 26.5

7.5 x 14.0 x 26.5

7.0 x 16.0 x 26.5

7.5 x 14.0 x 26.5

10.5 x 16.5 x 26.5

11.0 x 20.5 x 26.5

12.0 x 22.0 x 26.5

B32673Z4224+***

B32673T4224+***

B32673Z4334+***

B32673T4334+***

B32673Z4474+***

B32673T4474+***

B32673Z4684+***

B32673T4684+***

B32673Z4105+***

B32673Z4155+***

B32673Z4225+***

100

80000

680

550

680

550

680

550

580

550

390

370

-

700

500

700

500

700

500

600

500

400

350

-

720

570

720

570

720

570

630

570

540

510

450

22.5

520 277 0.22

0.22

0.33

0.47

0.68

1.00

1.50

6.0 x 15.0 x 26.5

7.5 x 14.0 x 26.5

6.0 x 15.0 x 26.5

7.5 x 14.0 x 26.5

7.0 x 16.0 x 26.5

7.5 x 14.0 x 26.5

10.5 x 16.5 x 26.5

10.5 x 20.5 x 26.5

12.0 x 22.0 x 26.0

B32673Z5224+***

B32673T5224+***

B32673Z5334+***

B32673T5334+***

B32673Z5474+***

B32673T5474+***

B32673Z5684+***

B32673Z5105+***

B32673Z5155+***

120

125000

680

550

680

550

580

550

390

-

700

500

700

500

600

500

400

-

720

570

720

570

630

570

540

450

Further E series and intermediate capacitance values on request.

Composition of ordering code see page 2

Film capacitors

MKP 2 pin capacitors, RoHS compatible B32672…3Z

FK PM 2007-08-16

Please read Cautions and warnings and Page 4 of 7

Important notes at the end of this document.

Technical data

Maximum operating temperature Top,max +110 ºC

C

R ≤ 0.1 µF 0.1 µF<CR

Dissipation factor tan δ (in 10-3 ) at 20 °C

(upper limit values) at 1 kHz

100 kHz

1.0

5

1.0

–

Insulation resistance Ris or time constant

τ= CR ⋅Ris at 20 °C, rel. humidity ≤65%

(minimum as-delivered values)

30 000 MΩ

DC test voltage 1.6 x VR, 2 s

Passive flammability category

In accordance with IEC 40 (CO) 752 C

Maximum continuous AC voltage (VAC ) 220 V / 277 V / 310 V (50/60 Hz)

Surge pulse test IEC 1000-4-5 1.2 µs / 50 µs / 1200 V

8.0 µs / 20 µs / 1200 V

Damp heat test

Limit values after damp heat test

56 days / 40 °C / 93% relative humidity

Capacitance change (ΔC/ C)

Dissipation factor change (Δtan δ

Insulation resistance Ris

or time constant τ= CR ⋅Ris

≤ 5%

≤ 0.5 •10-3 (at 1 kHz)

≤1,0 •10-3 (at 10 kHz)

≥ 50% of minimum

as-delivered values

Pulse handling capability

“dv/dt” values represent the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in

V/µs.

“K0” represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs.

Note: The maximum values of dv/dt and K0 must not be exceeded in order to avoid damaging the capacitor.

Film capacitors

MKP 2 pin capacitors, RoHS compatible B32672…3Z

FK PM 2007-08-16

Please read Cautions and warnings and Page 5 of 7

Important notes at the end of this document.

Cautions and warnings

General notes on soldering

Permissible heat-exposure loads on film capacitors are primarily characterized by the upper category

temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead

to changes in the plastic dielectric and thus irreversibly change a capacitor's electrical characteristics.

For short exposure times (as in practical soldering processes), the heat load (and thus the possible

effects on the capacitor) will also depend on other factors such as:

 The pre-heating temperature and time.

 The forced cooling immediately after soldering.

 The terminal characteristics: diameter, length, thermal resistance, special configurations (e.g.

crimping).

 The height of the capacitor above the solder bath.

 Shadowing by neighboring components.

 Additional heating due to heat dissipation by neighboring components.

 Use of solder-resistant coatings.

The overheating associated with some of these factors can usually be reduced by suitable

countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced

cooling process may have to be included.

Cleaning

To determine whether a particular solvent, often used to remove flux residues and other substances,

is suitable for the capacitors described, please refer to latest data book “Film Capacitors”, in which

this information is available. Even when suitable solvents are used, a reversible change of the

electrical characteristics may occur in uncoated capacitors immediately after they have been washed.

Thus it is always recommended to dry the components (e.g. 4 h at 70 °C) before they are subjected to

subsequent electrical testing.

Embedding of capacitors in finished assemblies

In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both

chemical and thermal influences of the embedding (“potting”) and curing processes must be taken

into account. Our experience has shown that the following potting materials can be recommended

considering maximum curing temperature 100 °C:

 Non-flexible epoxy resins with acid-anhydride hardeners

 Chemically inert, non-conducting fillers

Storage conditions

All capacitors listed in this product profile can be stored for short periods at any temperature within the

entire range of category temperatures. For long storage periods, however, the following conditions

should be observed:

 Storage temperature – 40 to +40 °C

 Maximum relative humidity 80%, no dew allowed on the capacitor

 Maximum duration 24 months (12 months for taped components)

Film capacitors

MKP 2 pin capacitors, RoHS compatible B32672…3Z

FK PM 2007-08-16

Please read Cautions and warnings and Page 6 of 7

Important notes at the end of this document.

Resistance to vibration

A capacitor's ability to withstand vibration (e.g. such as that occurring in applications involving rotating

machinery) is tested to IEC 60068-2-6. The test procedure used here involves continuous sinusoidal

vibration along three orthogonal axes, with a continuously varying frequency (10 … 500 Hz), an

acceleration amplitude of 10 g, a displacement amplitude of 0.75 mm and a duration of 360 minutes

for each axis. EPCOS offers film capacitors specially designed for operation under more severe

vibration regimes such as those found in automotive applications. Consult our catalog “Film

Capacitors for Automotive Electronics”.

Passive flammability

The passive flammability test is applied to ensure that components bearing the corresponding

qualification contribute less energy to the combustion behavior of their immediate vicinity than is

required to ignite them. This measure is designed to contain any localized fire that may occur. In the

respective tests, the capacitors are subjected to a standardized flame to evaluate their combustion

behavior by checking whether the flame persists for longer than a maximum permissible period or not.

The severity of the test is determined essentially by the test flame and exposure time in accordance

with various international standards (IEC 60040 CO 752 (amendment to IEC 60384-1), IEC 60695-2-

2 and UL 1414). Unless the detail specifications stipulate otherwise, EMI suppression capacitors are

tested to IEC 60384-14, section 4.17, test severity categories B and C.

Important notes

Page 7 of 7

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical

requirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application. As a

rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them

than the customers themselves. For these reasons, it is always ultimately incumbent on the

customer to check and decide whether an EPCOS product with the properties described in the

product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of passive electronic components

or failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in which

the malfunction or failure of a passive electronic component could endanger human life or health

(e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of

suitable design of the customer application or other action taken by the customer (e.g. installation

of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the

event of malfunction or failure of a passive electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as “hazardous”). Useful information on this will be found in our

Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more

detailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order.

We also reserve the right to discontinue production and delivery of products. Consequently,

we cannot guarantee that all products named in this publication will always be available.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of

the “General Terms of Delivery for Products and Services in the Electrical Industry”

published by the German Electrical and Electronics Industry Association (ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, MiniBlue, MKK, MLSC, MotorCap,

PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID,

SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or

pending in Europe and in other countries. Further information will be found on the Internet at

www.epcos.com/trademarks.