ACA1205 750/870 MHz CATV Line Amplifier Data Sheet - Rev 2.0 FEATURES * * * * * * * * * 15 dB Gain Very Low Distortion Excellent Input/Output Match Low DC Power Consumption Good RF Stability with High VSWR Load Conditions Surface Mount Package Compatible with Automatic Assembly Low Cost Repeatability of Monolithic Fabrication Meets Cenelec Standard APPLICATIONS * * CATV Distribution Amplifier High Linearity CATV Amplifier S7 Package 16 Pin Wide Body SOIC with Heat Slug PRODUCT DESCRIPTION The ACA1205 is a surface mount monolithic GaAs RF Linear Amplifier that has been developed to replace, in new designs, the standard CATV Hybrid amplifiers currently in use. The MMIC consist of two RF Input parallel amplifiers, each with 15 dB gain. The amplifier is optimized for exceptionally low distortion and noise figure while providing flat gain and excellent input and output return loss. 15dB 12dB 15dB 12dB ACA1205 ACA0861B Figure 1: Hybrid Application Diagram 08/2001 RF Output ACA1205 1 GND GND 16 2 N/C VA 15 3 RFINA RFOUTA 14 4 GND GND 13 5 GND GND 12 6 RFINB RFOUTB 11 7 IADJ VB 10 8 GND GND 9 Figure 2: Pin Out Table 1: Pin Description 2 PIN N AME D ESC R IPTION PIN N AME D ESC R IPTION 1 GND Ground 9 GND Ground 2 N/C No C onnecti on 10 VB Supply for Ampli fi er B 3 RFINA Input to Ampli fi er A 11 RFOUTB Output from Ampli fi er B 4 GND Ground 12 GND Ground 5 GND Ground 13 GND Ground 6 RFINB Input to Ampli fi er B 14 RFOUTA Output from Ampli fi er A 7 IADJ C urrent Adjust 15 VA Supply for Ampli fi er A 8 GND Ground 16 GND Ground Data Sheet - Rev 2.0 08/2001 ACA1205 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PAR AMETER MIN MAX U N IT Ampli fi er Suppli es (pi ns 10, 11, 14, 15) 0 +15 VD C RF Input Power (pi ns 3, 6) - +70 dBmV -65 +150 C Solderi ng Temperature - +260 C Solderi ng Ti me - 5.0 se c Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: 1. Pins 3 and 6 should be AC-coupled. No external DC bias should be applied. 2. Pin 7 should be pulled to ground through resistor R1, as shown in Figure 3. No external DC bias should be applied. Table 3: Operating Ranges PAR AMETER MIN TYP MAX U N IT RF Frequency 40 - 870 MHz - +12 - VD C -40 - +110 Supply: VDD (pi ns 10, 11, 14, 15) Operati ng Temperature C O The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.0 08/2001 3 ACA1205 Table 4: Electrical Specifications (TA= +25C, VDD = +12 VDC) PAR AMETER MIN TYP MAX U N IT 14.5 15 15.5 dB -0.3 - +0.3 dB - 2.5 3.5 dB 77 C hannels 110 C hannels 128 C hannels - -70 -68 -65 -64 - dB c dB c dB c 77 C hannels 110 C hannels 128 C hannels - -71 -71 -70 -66 - dB c dB c dB c 77 C hannels 110 C hannels 128 C hannels - -67 -63 -59 -56 - dB c dB c dB c - 180 200 mA -0.5 - 1.0 dB 18 22 - dB - - 6.0 C /W Gai n (1) Gai n Flatness Noi se Fi gure C TB (1) (2) (2),( 3) C SO (2),( 3) XMOD (2),( 3) Supply C urrent C able Equi valent Slope (1) Return Loss (i nput/Output) (1) Thermal Resi stance Notes: (1) Measured performance of MMIC alone. Balun effects deimbedded from measurement. (2) Measured with a balun on input and output of the device. See Figure 3 for test setup. (3) Part measured with 110 channel flat input, +34 dBmV output (per channel). +12 Vdc 1 N/C 2 ACA1205 16 12dB 15 3 14 4 13 .01 uF 390 nH 300pF .01 uF RF IN 5 .01 uF 12dB 12 6 11 7 10 8 9 3.6 K R1 RF Out 300pF 390 nH .01 uF +12 Vdc Note: Apply voltage to both +12Vdc lines simultaneoulsy Figure 3: Test Circuit 4 Data Sheet - Rev 2.0 08/2001 ACA1205 PERFORMANCE DATA Figure 4: Gain/ S21 vs. Frequency 17 16 S21 (dB) 15 14 13 12 11 0 200 400 600 800 1000 Frequency (MHz) Figure 5: Input Return Loss/ S11vs. Frequency 0 -5 S11 (dB) -10 -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure 6: Output Return Loss/ S22 vs. Frequency 5 0 -5 S22 (dB) -10 -15 -20 -25 -30 -35 -40 0 200 400 600 800 1000 Frequency (MHz) Data Sheet - Rev 2.0 08/2001 5 ACA1205 Figure 7: Reverse Isolation/ S12 vs. Frequency 0 -5 -10 S12 (dB) -15 -20 -25 -30 -35 -40 -45 -50 0 200 400 600 800 1000 Frequency (MHz) Figure 8: Noise Figure vs. Frequency 4 3.5 Noise Figure (dB) 3 2.5 2 1.5 1 0.5 0 0 100 200 300 400 500 600 700 800 900 Frequency (MHz) Figure 9: CTB vs. Frequency (112 Channel Loading, Flat +34dBmV Output Level) -50 CTB (dBc) -55 -60 -65 -70 -75 -80 0 200 400 Frequency (MHz) 6 Data Sheet - Rev 2.0 08/2001 600 800 ACA1205 Figure 10: XMOD vs. Frequency (112 Channel Loading, Flat +34dBmV Output Level) -45 XMOD (dBc) -50 -55 -60 -65 -70 -75 0 200 400 600 800 Frequency (MHz) Figure 11: CSO vs. Frequency (112 Channel Loading, Flat +34dBmV Output Level) -60 CSO (dBc) -65 -70 -75 -80 -85 -90 55 124 193 262 331 400 469 538 607 676 745 Frequency (MHz) Data Sheet - Rev 2.0 08/2001 7 ACA1205 APPLICATION INFORMATION The ACA1205 is designed as an input stage. This part can be used alone for low gain, low output level applications or can be cascaded with one of the ACA0861 output stages for higher gain and output signal drive level. The ACA1205 is a low power dissipation part designed as a driver for the ACA0861B output stage. Figure 12: Evaluation Board Layout Figure 13: Evaluation Board Schematic 8 Data Sheet - Rev 2.0 08/2001 ACA1205 Table 5: Evaluation Board Parts List ITEM D ESC R IPTION QU AN TITY VEN D OR VEN D OR P/N C 1,C 2,C 5,C 6 0.01uF. C HIP C AP. 4 MURATA GRM39X7R1103K25V C 3,C 4 300 pF. C HIP C AP. 2 MURATA GRM39X7R301K25V C7 47 uF ELEC T.C AP. 1 D IGI-KEY C ORP. P5275-ND C9 NOT USED L1,L2 390 nH C HIP IND . 2 C OILC RAFT 1008C S-391 C ORE 2 PHILLIPS TC 3.4/1.8/1.3-3D 3 MWS WIRE IND . B2383611 (66256-01) T1,T2- BALUN WIRE R1 3.6k OHMS 1 D GI-KEY C ORP. P3.6KAC T-ND TVS TVS 12 VOLT. 600 WATT 1 D IGI-KEY C ORP. SMBJ12AC C C T-ND C ONNEC TOR 75 OHMS. N MALE PANEL MOUNT. 2 PASTERNAC K ENTERP. P E 4504 PRINTED C IRC UIT BOARD 1 300 x 160 MILS 1 IND IUM C ORP. OF AMERIC A 14996Y IND IUM Notes: 1. T1, T2 (balun) wind 4 turns thru core as shown. (Figure 14). 2. N connector,center pin,should be approximately 80 mils in length. 3. Due to the high power dissapation of this devide the PC board should be mounted/ attached to a large heat sink. Figure 14: Balun Drawing Data Sheet - Rev 2.0 08/2001 9 ACA1205 PACKAGE OUTLINE Figure 15: S7 Package Outline - 16 Pin Wide Body SOIC with Heat Slug 10 Data Sheet - Rev 2.0 08/2001 ACA1205 NOTES Data Sheet - Rev 2.0 08/2001 11 ACA1205 ORDERING INFORMATION OR D ER N U MB ER TEMPER ATU R E R AN GE PAC K AGE D ESC R IPTION C OMPON EN T PAC K AGIN G AC A1205S7C TR -40C to 110C 16 Pi n Wi de Body SOIC wi th Heat Si nk 1,500 Pi ece Tape & Reel A C A 1205S 7C -40C to 110C 16 Pi n Wi de Body SOIC wi th Heat Si nk Plasti c Tubes (25 pcs. per tube) ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a products formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 Data Sheet - Rev 2.0 08/2001