Product Specification RoHS-6 Compliant 10Gb/s SFPwire(R) SFP+ Active Optical Cable FCBG110SD1Cxx PRODUCT FEATURES * Hot-pluggable SFP+ cable ends * Supports 10.3125 Gb/s bit rate * RoHS-6 compliant (lead-free) * Available in lengths up to 20m * SFI Limiting interface * Single 3.3V power supply * Low power dissipation * Commercial temperature range: 0C to 70C * APPLICATIONS * 10G Ethernet Data Center Intra-Rack and Inter-Rack links Rigid pull-tab for improved highdensity installations Finisar's FCBG110SD1Cxx 10Gb/s SFPwire(R) SFP+ active optical cables are designed for use in 10-Gigabit Ethernet links. They are electrically compliant with SFF-84311, and the mechanical SFP+ plug is compatible with SFF-84322. SFPwire is SFI limiting. No host electrical transmitter pre-emphasis is required. No host electrical receiver linear equalization is required. Host board designers using an EDC PHY IC should follow the IC manufacturer's recommended settings for interoperating the host-board EDC PHY with a limiting receiver. SFPwire is compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details. PRODUCT SELECTION* FCBG110SD1C01 FCBG110SD1CA5 FCBG110SD1C02 FCBG110SD1CB5 FCBG110SD1C03 FCBG110SD1CC5 * 1-meter cable 1.5-meter cable 2-meter cable 2.5-meter cable 3-meter cable 3.5-meter cable FCBG110SD1C05 FCBG110SD1C07 FCBG110SD1C10 FCBG110SD1C15 FCBG110SD1C20 5-meter cable 7-meter cable 10-meter cable 15-meter cable 20-meter cable Adding the letter "B" to the end of the part number specifies bulk packaging/shipping option. Finisar Corporation - July 2015 Rev. C1 Page 1 FCBG110SD1Cxx Product Specification I. Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VEET TFAULT TDIS SDA SCL MOD_ABS RS0 RX_LOS RS1 VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. 2-wire Serial Interface Data Line 2-wire Serial Interface Clock Line Module Absent. Grounded within the module No connection required Loss of Signal indication. Logic 0 indicates normal operation. No connection required Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 4 4 4 5 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. is an open collector/drain output, which is pulled up with a 4.7k - 10k resistor on the host 2. T FAULT 3. 4. 5. board, but is grounded inside the SFP+ cable plug. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. Should be pulled up with 4.7k - 10k on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. LOS is open collector output. Should be pulled up with 4.7k - 10k on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. 1 Towards Bezel 2 TX_Fault 3 TX_Disable 4 SDA 5 SCL 6 RS0 8 RX_LOS 10 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 MOD_ABS 7 9 VeeT VeeT RD+ 13 RD- 12 VeeR 11 Towards ASIC RS1 VeeR Figure 1. Diagram of Host Board Connector Block Pin Numbers and Names. Finisar Corporation - July 2015 Rev. C1 Page 2 FCBG110SD1Cxx Product Specification II. Absolute Maximum Ratings Exceeding the limits below may damage the active optical cable permanently. Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Symbol Vcc TS TA RH Min -0.5 -40 0 0 Typ Max 4.0 85 70 85 Unit V C C % Ref. 1 2 Notes: 1. Assumes no mechanical load force on the unit. Ensuring no mechanical load force requires a cable bend radius of >105 mm within 100 mm of either cable and SFP+ end and >60 mm on the rest of the cable. Otherwise, the storage temperature range is -20 to 75C. Non-condensing. III. Electrical Characteristics (each cable end, TOP = 0 to 70 C, VCC = 3.14 to 3.46 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Differential data output swing Data output rise time, fall time LOS Fault LOS Normal Power Supply Noise Tolerance Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr VLOS fault VLOS norm VccT/VccR Min 3.14 Typ Max 3.46 250 Unit V mA Ref. mV V V 1 700 Vcc Vee+ 0.8 mV ps V V mVpp 2,6 3 4 4 5 100 180 2 Vee 300 850 28 2 VccHOST Vee Vee+0.8 Per SFF-8431 Rev 4.1 Notes: 1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 2. Into 100 differential termination. 3. 20 - 80% . Measured with Module Compliance Test Board and OMA test pattern. Use of four 1's and four 0's in sequence in the PRBS^9 is an acceptable alternative. SFF-8431 Rev 4.1 4. LOS is an open collector output. Should be pulled up with 4.7k - 10k on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 5. Testing methodology per SFF-8431. Rev 4.1 6. The FCBG110SD1Cxx is SFI Limiting. Host board designers using an EDC PHY IC should follow the IC manufacturer's recommended settings for interoperating the host-board EDC PHY with a limiting receiver. Finisar Corporation - July 2015 Rev. C1 Page 3 FCBG110SD1Cxx Product Specification IV. General Specifications Parameter Bit Rate Bit Error Ratio Symbol BR BER Min Typ 10.3 Max Units Gb/s 10-15 Ref. 1 Notes: 1. Tested with a 231 - 1 PRBS V. Environmental Specifications The FCBG110SD1Cxx SFPwire has a commercial operating temperature range from 0C to 70C case temperature. Parameter Case Operating Temperature Storage Temperature Symbol Top Min 0 Tsto -40 Typ Max 70 Units C Ref. 85 C 1 Notes: 1. Assumes no mechanical load force on the unit. Ensuring no mechanical load force requires a cable bend radius of >105 mm within 100 mm of either cable and SFP+ end and >60 mm on the rest of the cable. Otherwise, the storage temperature range is -20 to 75C. VI. Regulatory Compliance The FCBG110SD1Cxx SFPwire, which contains laser devices, is a Class 1 laser product and complies with 21CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007, and it complies with EN(IEC) 60825 Edition 1.2 regulations. The FCBG110SD1Cxx is also RoHS Compliant. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation - July 2015 Rev. C1 Page 4 FCBG110SD1Cxx Product Specification VII. Mechanical Specifications The FCBG110SD1Cxx SFPwire SFP+ cable ends are compatible with the SFF-8432 specification for improved pluggable form factor. Rigid pull-tab and cable jacket color are black. Figure 2. FCBG110SD1Cxx Mechanical Dimensions. FCBG110SD1Cxx SFPwire(R) cable details Description Cable Jacket Material Cable Flammability Rating Cable Outer Diameter Cable Tensile Load (Short Term) Cable Tensile Load (Long Term) Crush Resistance Impact Resistance Flexing Twist Bend Cable to SFP+ Plug Connection Bend Radius (Short Term) Bend Radius (Long Term) Durability Finisar Corporation - July 2015 Min Typ Max Units Notes PVC OFNR 2.8 3.0 3.2 200 100 10 0.5 300 90 25 30 100 Rev. C1 mm Newtons Newtons Newtons/mm Newton*m Cycles FOTP-41 FOTP-25 FOTP-104 Exceeds FOTP-85 Newtons mm mm Cycle Min Page 5 FCBG110SD1Cxx Product Specification VIII. PCB Layout and Bezel Recommendations Figure 3. Finisar Corporation - July 2015 Rev. C1 Page 6 FCBG110SD1Cxx Product Specification Figure 4. Finisar Corporation - July 2015 Rev. C1 Page 7 FCBG110SD1Cxx Product Specification IX. Host - Active optical cable end Interface Block Diagram Figure 5. Finisar Corporation - July 2015 Rev. C1 Page 8 FCBG110SD1Cxx Product Specification X. References 1. "Specifications for Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module `SFP+ `", SFF Document Number SFF-8431, Revision 4.1. 2. "Improved Pluggable Formfactor", SFF Document Number SFF-8432, Revision 4.2, April 18, 2007. 3. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". Certain products may use one or more exemptions as allowed by the Directive 4. "Application Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers" XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - July 2015 Rev. C1 Page 9