PC8141xNSZ
Series
1. Recognized by UL1577 (Double protection isolation),
file No. E64380 (as model No. PC8141)
2. Package resin : UL flammability grade (94V-0)
■ Features
■ Agency approvals/Compliance
1. Programmable controllers
2. Facsimiles
3. Telephones
■ Applications
DIP 4pin High CMR,
AC Input, Low Input Current
Photocoupler
1. 4-pin DIP package
2. Double transfer mold package (Ideal for Flow Solder-
ing)
3. AC input type
4. Low input current type (IF=±0.5mA)
5. High collector-emitter voltage (VCEO : 80V(*))
6. High noise immunity due to high common rejection
voltage (CMR : MIN. 10kV/µs)
7. High isolation voltage between input and output
(Viso(rms) : 5.0 kV)
(*)Up to Date code "P8"(August 2002)VCEO:70V.
■ Description
PC8141xNSZ Series contains an IRED optically
coupled to a phototransistor.
It is packaged in a 4-pin DIP, available in SMT gullw-
ing lead-form option.
Input-output isolation voltage(rms) is 5.0kV.
Collector-emitter voltage is 80V(*), CTR is 50% to
600% at input current of ±0.5mA and CMR is MIN.
10kV/µs.
1Sheet No.: D2-A03701EN
Date Sep. 30. 2003
© SHARP Corporation
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PC8141xNSZ Series
■ Internal Connection Diagram
Anode/Cathode
Cathode/Anode
Emitter
Collector
1
1
2
3
4
2
4
3
2
Sheet No.: D2-A03701EN
■ Outline Dimensions
Product mass : approx. 0.25g
(Unit : mm)
1. Through-Hole [ex. PC8141xNSZ] 2. SMT Gullwing Lead-Form [ex. PC8141xNIZ]
6.5±0.5
7.62±0.3 4.58±0.5
θθ
θ : 0 to 13˚
Epoxy resin
0.26±0.1
3.5±0.5
3.0±0.5
0.5TYP.
0.6±0.2
1.2±0.3
1
2
4.58±0.5
2.54±0.25
4
3
Primary side
mark Rank mark
Factory identification mark
Date code
8141
2.7±0.5
0.5±0.1
0.6±0.2
1.2±0.3
6.5±0.5
7.62±0.3
0.26±0.1
4.58±0.5
2.54±0.25
Epoxy resin
3.5±0.5
4.58±0.5
2.54±0.25
4
3
Rank mark
Factory identification mark
1.0+0.4
−0
1.0+0.4
−0
10.0+0
−0.5
0.35±0.25
1
2
Primary side
mark
Date code
8141
PC8141xNSZ Series
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
Mark
A
B
C
D
E
F
H
J
K
L
M
N
Mark
P
R
S
T
U
V
W
X
A
B
C
Mark
1
2
3
4
5
6
7
8
9
O
N
D
Month
January
February
March
April
May
June
July
August
September
October
November
December
A.D
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
·
·
··
·
·
2nd digit
Month of production
1st digit
Year of production
Factory identification mark
Factory identification Mark
no mark
Country of origin
Japan
Indonesia
Philippines
China
* This factory making is for identification purpose only.
Please contact the local SHARP sales representative to see the actual status of the
production.
3
repeats in a 20 year cycle
Sheet No.: D2-A03701EN
PC8141xNSZ Series
Date code (2 digit)
Rank mark
Refer to the Model Line-up table
Sheet No.: D2-A03701EN
■ Electro-optical Characteristics
Parameter Conditions
Forward voltage
Terminal capacitance
Collector dark current
Collector-emitter breakdown voltage
Transfer
charac-
teristics
Collector current
Collector-emitter saturation voltage
Emitter-collector breakdown voltage
Isolation resistance
Floating capacitance
MIN.
−
−
−
80
0.25
−
5×1010
−
−
10
TYP.
1.2
30
−
−
−
−
−
1×1011
0.6
3
−
MAX.
1.4
250
100
−
2.0
−
0.2
−
1.0
18
−
Unit
V
V
pF
nA
V
mA
V
Ω
µs
µs
kV/µs
Symbol
VF
Ct
ICEO
BVCEO
BVECO
IC
VCE (sat)
RISO
tf
CMR
Cf
Response time
Common mode rejection voltage
Rise time
Fall time
Input
Output
IF=±10mA
V=0, f=1kHz
VCE=50V, IF=0
IC=0.1mA, IF=0
IE=10µA, IF=0
IF=±0.5mA, VCE=5V
DC500V, 40 to 60%RH
Ta=25˚C, RL=470Ω, VCM=1.5kV(peak)
IF=0, VCC=9V, Vnp=100mV
VCE=2V, IC=2mA, RL=100Ω−418
pF
tr
V=0, f=1MHz
IF=±10mA, IC=1mA
6
(Ta=25˚C)
*5 Up to Date code "P8"(August 2002)BVCEO≥70V.
*5
■ Absolute Maximum Ratings (Ta=25˚C)
Parameter Symbol Unit
Input
Forward current mA
*1 Peak forward current mA
Power dissipation mW
Output
Collector-emitter voltage
V
Emitter-collector voltage
V
Collector current mA
Collector power dissipation
mW
Total power dissipation mW
*2 Isolation voltage
Operating temperature ˚C
Storage temperature ˚C
*3 Soldering temperature
IF
IFM
P
VCEO
VECO
IC
PC
Ptot
Viso (rms)
Topr
Tstg
Tsol ˚C
*1 Pulse width≤100µs, Duty ratio : 0.001
*2 40 to 60%RH, AC for 1 minute, f=60Hz
*3 For 10s
*4 Up to Date code "P8"(August 2002)VCEO:70V.
Rating
±10
±200
15
80
6
50
150
170
−30 to +100
−55 to +125
260
5.0 kV
*4
4
PC8141xNSZ Series
Sheet No.: D2-A03701EN
■ Model Line-up
IC [mA]
(I
F
=±0.5mA, V
CE
=5V, T
a
=25˚C)
Lead Form
Package Rank mark
with or without
A
0.25 to 2.0
0.5 to 1.5
PC81410NSZ
PC81411NSZ
Through-Hole
PC81410NIZ
PC81411NIZ
SMT Gullwing
Sleeve
100pcs/sleeve
Model No.
5
Please contact a local SHARP sales representative to inquire about production status and Lead-Free options.
PC8141xNSZ Series
Sheet No.: D2-A03701EN
Total power dissipation Ptot (mW)
Ambient temperature Ta (˚C)
0
200
150
170
100
50
−30 0 25 50 75 100 125
Fig.5 Total Power Dissipation vs. Ambient
Temperature
Forward current IF (mA)
Ambient temperature Ta (˚C)
0
10
5
−30 0 25 50 75 100 125
Fig.2 Forward Current vs. Ambient
Temperature
Diode power dissipation P (mW)
Ambient temperature Ta (˚C)
0
15
10
5
−30 0 25 50 75 100 125
Fig.3 Diode Power Dissipation vs. Ambient
Temperature
Collector power dissipation PC (mW)
Ambient temperature Ta (˚C)
0
200
150
100
50
−30 0 25 50 75 100 125
Fig.4 Collector Power Dissipation vs.
Ambient Temperature
6
Fig.1 Test Circuit for Common Mode Rejection Voltage
VCM
Vcp Vnp
VO
(dV/dt)
*
RLVnp
VCC
VCM
(Vcp Nearly = dV/dt×Cf×RL)
* Vcp : Voltage which is generated by displacement current in floating
capacitance between primary and secondary side.
VCM : High wave
pulse
RL=470Ω
VCC=9V
PC8141xNSZ Series
Sheet No.: D2-A03701EN
Relative current transfer ratio (%)
Ambient temperature Ta (˚C)
−30 1009080706050403020100−10−20
VCE=5V
IF=0.5mA
0
150
100
50
Fig.10 Relative Current Transfer Ratio vs.
Ambient Temperature
Collector-emitter saturation voltage VCE (sat) (V)
Ambient temperature Ta (˚C)
0
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
IF=10mA
IC=1mA
−30 1009080706050403020100−10−20
Fig.11 Collector - emitter Saturation Voltage
vs. Ambient Temperature
7
Collector current IC (mA)
Collector-emitter voltage VCE (V)
0
40
0246810
Ta=25˚C
30
20
10
PC (MAX.)
IF=7mA
IF=5mA
IF=3mA
IF=2mA
IF=1mA IF=0.5mA
Fig.9 Collector Current vs. Collector-emitter
Voltage
Current transfer ratio CTR (%)
Forward current IF (mA)
0.1 1 10
0
500
400
300
200
100
VCE=5V
Ta=25˚C
Fig.8 Current Transfer Ratio vs. Forward
Current
Forward current IF (mA)
0.1
1
10
100
0 0.5 1.0 1.5 2.0
Forward voltage VF (V)
Ta=25˚C
Ta=75˚C
Ta=100˚C
Ta=50˚C
Ta=0˚C
Ta=−25˚C
Fig.7 Forward Current vs. Forward Voltage
Peak forward current IFM (mA)
Duty ratio
10
1 000
100
10−2
10−310−1
22255551
2 000
200
20
500
50
Pulse width≤100µs
Ta=25˚C
Fig.6 Peak Forward Current vs. Duty Ratio
PC8141xNSZ Series
Sheet No.: D2-A03701EN
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
8
Voltage gain AV (dB)
−25
5
0.1 1 10 100 1 000
Frequency f (kHz)
VCE=2V
IC=2mA
Ta=25˚C
0
−5
−10
−15
−20
RL=10kΩ
1kΩ
100Ω
Fig.16 Frequency Response
Ambient temperature Ta (˚C)
−30 1009080706050403020100−10−20
VCE=50V
10−11
10−5
10−6
10−7
10−8
10−9
10−10
Collector dark current ICEO (A)
Fig.12 Collector Dark Current vs. Ambient
Temperature
Load resistance RL (kΩ)
0.1
1
10
100 VCE=2V, IC=2mA
1
tf
ts
tr
td
10
Responce time (µs)
Fig.13 Response Time vs. Load Resistance
(active region )
10%
Input
Output
Input Output
90%
ts
td
VCC
RDRL
tf
tr
Please refer to the conditions in Fig.13 and Fig.14.
VCE
Fig.15 Test Circuit for Response Time
Load resistance RL (kΩ)
1
1
10
100
1 000 Vcc=5V, IF=1mA, Ta=25˚C
10
tf ts
tr
td
100
Responce time (µs)
Fig.14 Response Time vs. Load Resistance
(saturation region)
Collector-emitter saturation voltage VCE (sat) (V)
Forward current IF (mA)
0
5
0246810
Ta=25˚C
4
3
2
1
IC=7mA
IC=5mA
IC=3mA
IC=2mA
IC=1mA
IC=0.5mA
Fig.17 Collector-emitter Saturation Voltage
vs. Forward Current
PC8141xNSZ Series
Sheet No.: D2-A03701EN
■ Design Considerations
While operating at IF<0.5mA, CTR variation may increase.
Please make design considering this fact.
In case that some sudden big noise caused by voltage variation is provided between primary and secondary
terminals of photocoupler some current caused by it is floating capacitance may be generated and result in
false operation since current may go through IRED or current may change.
If the photocoupler may be used under the circumstances where noise will be generated we recommend to
use the bypass capacitors at the both ends of IRED.
This product is not designed against irradiation and incorporates non-coherent IRED.
● Degradation
In general, the emission of the IRED used in photocouplers will degrade over time.
In the case of long term operation, please take the general IRED degradation (50% degradation over 5years)
into the design consideration.
● Recommended Foot Print (reference)
✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes.
9
2.2
2.54
1.7
8.2
(Unit : mm)
● Design guide
PC8141xNSZ Series
Sheet No.: D2-A03701EN
■ Manufacturing Guidelines
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
● Soldering Method
Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below
listed guidelines.
Flow soldering should be completed below 270˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
10
PC8141xNSZ Series
1234
300
200
100
00
(˚C)
Terminal : 260˚C peak
( package surface : 250˚C peak)
Preheat
150 to 180˚C, 120s or less
Reflow
220˚C or more, 60s or less
(min)
Sheet No.: D2-A03701EN
Solvent cleaning:
Solvent temperature should be 45˚C or below Immersion time should be 3minutes or less
Ultrasonic cleaning:
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials:
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol
In case the other type of solvent materials are intended to be used, please make sure they work fine in ac-
tual using conditions since some materials may erode the packaging resin.
● Cleaning instructions
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances:CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
● Presence of ODC
11
PC8141xNSZ Series
Sheet No.: D2-A03701EN
■ Package specification
12
12.0
6.7
5.8
10.8
520
±2
● Sleeve package
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 100pcs of products shall be packaged in a sleeve.
Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its primary side mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
(Unit : mm)
PC8141xNSZ Series
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems rela-
ted to any intellectual property right of a third party re-
sulting from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the spec-
ifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability. Manufac-
turing locations are also subject to change without no-
tice.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connec-
tion with equipment that requires an extremely high lev-
el of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· If the SHARP devices listed in this publication fall with-
in the scope of strategic products described in the For-
eign Exchange and Foreign Trade Law of Japan, it is
necessary to obtain approval to export such SHARP de-
vices.
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be repro-
duced or transmitted in any form or by any means, elec-
tronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
· Contact and consult with a SHARP representative if
there are any questions about the contents of this pub-
lication.
13
Sheet No.: D2-A03701EN
■ Important Notices
PC8141xNSZ Series
