STANDARD
Resistive Touch Panel Specication
554 4-Wire Series RoHS compliant
n FEATURES
• Superior quality standard 4 wire resistive analog touch panel
• Excellent specication and high quality
- Anti Newton ring technology
- High reliability materials
• Pen/nger type
• Transparency - 80% typical
• RoHS compliant
Input Panel Panel Drive
change
over switch
Noise
Filter
MCU
Control
Section
A/D con-
verter
Interface
n PART NUMBERS
Touch Panels:
n PART NUMBERS
Controller Boards:
n PART NUMBERS
Interface Controller Chips:
N 2
N B
rebmuNtraP epyT
072B-8550-B61 32SR,eriW-4
037B-8550-B61 SU,eriW-4
N 2
N B
rebmuNtraP epyT
630V-9550-010 32SR,eriW-4
18
00-02114C SU,eriW-4
Part Number Size Type Part Number Size Type
T010-1201-T200 17.0” Pen/Finger T010-1301-T320 7.0” Pen/Finger (82%, AS)
N010-0554-T902 15.0” Pen/Finger N010-0514-T003 6.5” Pen/Finger (W 16:9, Automotive,
82%, AS)
N010-0554-T813 12.1” Pen/Finger (AS, DPET) N010-0514-T005 6.5” Pen/Finger (W 16:9, Automotive,
88%, AS)
N010-0554-T814 12.1” Pen/Finger T010-1301-T350 6.5” Pen/Finger (W 16:9)
N010-0554-T805 12.1” Pen/Finger N010-0518-T342 6.4” Pen/Finger (78% polarized)
N010-0554-T351 10.4” Pen/Finger (86%, AS) N010-0554-T048 6.4” Pen/Finger (86% clear)
N010-0554-T352 10.4” Pen/Finger (82%, AS) N010-0554-T043 6.4” Pen/Finger (80%, AG)
N010-0554-T347 10.4” Pen/Finger N010-0554-T009 5.7” Pen/Finger
N010-0516-T104 10.4” Pen/Finger (86%, Clear) N010-0554-T015 5.7” Pen/Finger
N010-0519-T742 8.4” Pen/Finger (86% Clear) N010-0554-T241 4.3” Pen Finger (86%, AS, DPET)
N010-0554-T504 8.4” Pen/Finger (0.7mm glass) N010-0556-T408 3.9” Pen/Finger (86% Clear)
N010-0554-T511 8.4” Pen/Finger (1.1mm glass) N010-0554-T703 3.8” Pen/Finger
N010-0516-T947 8.1” Pen/Finger (1.1mm glass) N010-0516-T407 3.7” Pen/Finger (0.7mm glass)
N010-0514-T101 7.0” Pen/Finger (W 16:9, Auto-
motive, 82%, AS, 50mm tail)
2
554 SERIES
n 1.0 APPLICATION
This specication applies to the standard FID-554 seriesTouch Panel (Pen/Finger type).
n 2.0 ADDITIONAL APPLICATIONS
Complete specication document is available upon request for customers with whom we have an approved
NDA in place.
n 3.0 DESCRIPTION AND BLOCK DIAGRAM
This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to
the host system (see block diagram above).
n 4.0 DRAWING (Please see the diagram above.)
Denitions of the major dimensions indicated on this diagram:
Effective Input Area (A) Area guaranteed to meet all the
characteristics detailed in this specication
Anti-input Area (C) An insulating area allowed to protect
the touch panel from giving false
readings when an enclosure touches
the panel. (See xing instructions)
n 5.0 CHARACTERISTICS
n 5.1 MECHANICAL
Operating Force 0.05~0.49 N (5 ~ 50gF) Measured with
a Silicon Measurement Rod R 8
(Round type 8mm) Silicon Rubber
Hardness 60˚C
Hardness of Surface Pencil hardness 3H minimum against
specication JIS K-5400
n 5.2 OPTICAL
Transparency 78% min. measured in the effective input area to JIS K 7105 using a
MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter.
Haze 5% type measured in the effective input area using a MURAKAMI
SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated
n DETAILED SPECIFICATION
Unit: mm
87.70
112.10
8.00
6.70
5.40
6.00
4.70
Left
15.00
#1 #4
212.20: Guaranteed active area
213.20
214.80: Boundary line of the top enclosure
216.20: Transparent area
5.50 Anti-input area
159.40: Guaranteed Active Area
160.40
162.00: Boundary Line of top enclosure
164.60: Transparent Area
4.00
5.40
6.70
175.40
7.50
228.20
(8.00)
(8.70)
9.50 Anti-input area
7.50 Anti-
input area
8.00
(10.00)
4.00
26.50
10.20
Right
Top
Bottom
5.00±0.5
75.00±1.0
87.70±0.1
n DIMENSION EXAMPLE (10.4” SHOWN)
Force
Silicon Rubber Rod
B
C
A
3
554 SERIES
n 5.3 ELECTRICAL
Rated Voltage: DC 7V max.
Resistance X axis: 300 to 850 Ω (at the connector)
Resistance Y axis: 100 to 600 Ω (at the connector)
Switch Bounce (Chattering): 20ms min when using the silicon rubber measurement rod
Insulation resistance: 10MΩ minimum at 25KV DC
Dielectric Strength: No problems when at 25KV DC for 1 minute
Linearity: 2% max.
Note 1:
Measurement condition of linearity is corrected within the
control IC. In general the location accuracy is specied
as follows:
Actual co-ordinate point - theoretical co-ordinate point
= location accuracy.
In general a 9 point co-ordinate calibration system is used
to adjust the micro controller accuracy. (20 point can be
used in combination with an EEPROM design).
n 5.4 ENVIRONMENTAL
Operating Temperature (*): -5˚C to 60˚C
Storage Temperature: -20˚C to 70˚C
Operating Humidity: 20% to 85% RH with a Maximum wet bulb temperature of 38˚C
Storage Humidity: 10% to 90% RH with a Maximum wet bulb temperature of 38˚C
Chemical Resistance: Coating with the following chemicals and storing at room temperature for 2
hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethyl-
alcohol, toluene, methyl-ethyl-ketone
Low Air Pressure: No issues down to 0.5 x Normal Air pressure
n 5.5 PEN LIFE
Note taking life: 100,000 words minimum
Input life : 1,000,000 times minimum
Note 1:
Words are written in the notes area and the size of the word is
7.5mm x 6.75mm. A word is any Alphabet / Number / Mark.
The pen is as shown below and applies a force of 250g.
A failure is judged to happen when the current consumption or
insulation resistance or dielectric strength are not met as
shown in 5.3. The location accuracy with 9 point calibration
must be ±4.4 mm max.
10mm
9 mm
Notes
Effective input area
3.5
ø6.0
ø2.0
9.0 1.0
110.0±1.0
3.0 1.5
ø 4.6
ø2.0
R 0.8
Distance
Co-ordinate Point
Theoretical
Actual
Error
4
554 SERIES
n 5.6 FINGER LIFE
A nger is simulated by a silicon rubber plunger
R8 (Round type 8mm size) hardness 60˚C at 200g
at frequency 5Hz.
A failure is judged to happen when the current
consumption or insulation resistance or dielectric
strength are not met as shown in 5.3. The location
accuracy with 9 point calibration must be ±4.4 mm max.
Operating force is 150g max.
n 5.7 INFORMATION ON THE PANEL
Production year 99 00 etc.
9 0 1 The left side number shows production year, eg 1999
0 1 2 The left side number shows production year, eg 2000
[ . . . . . . . . . . . ] The rst dot after the space shows production month, eg May
[ . . . . . . . . . . . ] The rst dot after the space shows production month, eg June
n 6 PACKAGING
n 6.1 PACKING SPECIFICATION
Vibration: 10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm
Drop test: 60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time
After the test no glass: aw or crack is seen, and no dent or scratch on the lm.
Also glass and lm must not separate.
n 6.1 PACKING DETAILS
Each touch panel is placed into a plastic bag and is
held in place by a slit cut into the side of the card-
board. A second insertion piece is placed into the
carton to again add stability. The qty is written on
the side of the box. For example the N010-0554-
T001 has 80 pieces per box.
Insert
Touch panel with bag
Slit in cardboard
550 Type panel illustrated (554 type packed
a similar way)
5
554 SERIES
n 7.0 REJECT CRITERIA
noitpircseD airetirCtcejeR
tneDmliF
mm1.0a ≥erA
2
mm50.0a ≥erA
2
mm1.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
ngieroF
lairetam
neewteb
mlifdnassalg
epyttoD
mm1.0>aerA
2
mm50.0a ≥erA
2
mm1.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
epyteniL
mm1.0a >erA
mm01<htgneldnamm1.0<htdiw&mm30.0a ≥erA
mm50.0<aerA
orezebot:
tniop1.xamebot:
deificepsenon:
hctarcS
mm1.0a ≥erA
mm08<htgnelhtiwmm1.0<htdiw&mm30.0a ≥erA
mm03<htgnelhtiwmm1.0<htdiw&mm30.0<aerA
orezebot:
tniop1.xamebot:
deificepsenon:
taocdrahrorulbtoD
gnissim
mm5.0a ≥erA
2
mm30.0a ≥erA
2
mm5.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
gniRnotweN 3(pmaltnecseroulfarednuedismliflenaPmorfneesebtontsumesehT
.edisssalgmrofdeifirevebottoN.)pmalepythtgnelevaw
walfssalG ehT.margaidgniwollofehtninwohstahtnahtreggibsihcihwwalfoneboT
.deificepstonsiswalfforebmun
n 8.0 GENERAL POINTS OF CAUTION
Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by
the cable or put any stress on the lm, for example moving by lm face vacuum. In order to clean wring dry a
cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solu-
tion. Watch the edge of the panel when cleaning, again for safety reasons.
2mm
2mm
5mm
3mm
6
554 SERIES
n 9.0 CONNECTION AND MOUNTING
The details below indicate the recommended mounting structure for panel and enclosure. The enclosure sup-
port to x the touch panel must be over 1.0mm I width and must be outside the view (Transparent area). Also
ensure that the enclosure does not cause miss input by touching the view area.
The following diagram shows that the enclosure edge must be between the View area and the guaranteed ac-
tive area. Ensure space is allocated for the diodes, and we recommend that the material to x the panel and
enclosure is elastic. Special design would be required to stop water ingress. The corners of the touch panel
are conductive so do not touch any metal parts after mounting.
Location Detect
1. Bottom
2. Left
3. Top
4. Right
Top View (Picture, with conductive
side down)
(Drawing) with conductive connector and glass
side down. See page 1 for detail of connector exit
side which is left.
(Mating connector type FCI or equivalent
SFW4R-1STAE1-LF: for FPC)
0.8 mm min.
Connector
LCD
1.0 to 3.0 mm
Circuit Board
Transparent Area
Anti-input Area
Shock absorber to protect
the panel (eg rubber)
Upper Case
Input Area
Shock absorber
for protection
View Area
Input Panel Wiring Area
7
554 SERIES
n 10.0 PANEL THICKNESS (typical)
Thickness of Glass 1.1mm
Stiffener Board
Conductive Face
0.30 ±0.05
1.40 ±0.2
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141 8630, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@fcl.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: components@us.fujitsu.com
Web: http://us.fujitsu.com/components/
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: emea.fujitsu.com/components/
Asia Pacic
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
Web: http://www.fujitsu.com/sg/services/micro/components/
Fujitsu Components International Headquarter Ofces
©2007 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.
Fujitsu Components America or its afliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our
products Fujitsu Components America, Inc. or its afliates reserve the right to change specications/datasheets without prior notice.
Rev. October 30, 2007.