INDUCTORS
MLG0402P 0402 [01005 inch]*
MLG0402Q 0402 [01005 inch]
MLG0603P 0603 [0201 inch]
* Dimensions Code JIS[EIA]
September 2014
Inductors for High Frequency Circuits
Multilayer Ceramic
MLG-Q
,
MLG-P
series
(2/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
Inductors for High Frequency Circuits
Multilayer Ceramic
FEATURES
High Q type inductor for high-frequency circuits.
The 0402 Series has0.2 to 33nH, and the 0603 Series has 0.6 to 120nH.
0.1n step inductance lineup.
Compared with existing products, the size was greatly reduced, making it optimal for fine-pitch circuits.
Optimal configuration that greatly improves the Q to 800MHz or higher.
Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for High-
frequency.
APPLICATION
Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the MLG-Q, MLG-P Series
MLG 0402 Q 0N2 S T 000
Series name L×W×H Dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (μH)
0402 0.4×0.2×0.2 P 1N1 1.1 B ±0.1nH T Taping 000
0603 0.6×0.3×0.3 Q 11N 11 C ±0.2nH
S ±0.3nH
H±3%
J±5%
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MLG0402P –55 to +125 –55 to +125 20000 0.07
MLG0402Q –55 to +125 –55 to +125 20000 0.07
MLG0603P –55 to +125 –55 to +125 15000 0.2
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
Overview of the MLG-Q, MLG-P Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries
MLG0402P Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.40±0.02
0.11±0.03 0.11±0.03
0.20±0.02 0.20±0.02
Dimensions in mm
0.18 to 0.20
0.15 to 0.2
0.2
0.15 to 0.2
(6/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Short bar residual inductance =0.11nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
0.2 ±0.1nH — 500 10.0 20.0 0.1 0.03 350 MLG0402P0N2BT000
0.2 ±0.2nH —500 10.0 20.0 0.1 0.03 350 MLG0402P0N2CT000
0.3 ±0.1nH — 500 10.0 20.0 0.1 0.03 350 MLG0402P0N3BT000
0.3 ±0.2nH —500 10.0 20.0 0.1 0.03 350 MLG0402P0N3CT000
0.4 ±0.1nH — 500 10.0 20.0 0.2 0.07 350 MLG0402P0N4BT000
0.4 ±0.2nH —500 10.0 20.0 0.2 0.07 350 MLG0402P0N4CT000
0.4 ±0.3nH — 500 10.0 20.0 0.2 0.07 350 MLG0402P0N4ST000
0.5 ±0.1nH —500 10.0 20.0 0.2 0.08 350 MLG0402P0N5BT000
0.5 ±0.2nH — 500 10.0 20.0 0.2 0.08 350 MLG0402P0N5CT000
0.5 ±0.3nH —500 10.0 20.0 0.2 0.08 350 MLG0402P0N5ST000
0.6 ±0.1nH — 500 10.0 20.0 0.2 0.11 350 MLG0402P0N6BT000
0.6 ±0.2nH —500 10.0 20.0 0.2 0.11 350 MLG0402P0N6CT000
0.6 ±0.3nH — 500 10.0 20.0 0.2 0.11 350 MLG0402P0N6ST000
0.7 ±0.1nH —500 10.0 20.0 0.3 0.13 320 MLG0402P0N7BT000
0.7 ±0.2nH — 500 10.0 20.0 0.3 0.13 320 MLG0402P0N7CT000
0.7 ±0.3nH —500 10.0 20.0 0.3 0.13 320 MLG0402P0N7ST000
0.8 ±0.1nH — 500 10.0 18.3 0.4 0.11 320 MLG0402P0N8BT000
0.8 ±0.2nH —500 10.0 18.3 0.4 0.11 320 MLG0402P0N8CT000
0.8 ±0.3nH — 500 10.0 18.3 0.4 0.11 320 MLG0402P0N8ST000
0.9 ±0.1nH —500 10.0 17.3 0.4 0.15 320 MLG0402P0N9BT000
0.9 ±0.2nH — 500 10.0 17.3 0.4 0.15 320 MLG0402P0N9CT000
0.9 ±0.3nH —500 10.0 17.3 0.4 0.15 320 MLG0402P0N9ST000
1.0 ±0.1nH 8 500 10.0 16.5 0.4 0.20 250 MLG0402P1N0BT000
1.0 ±0.2nH 8500 10.0 16.5 0.4 0.20 250 MLG0402P1N0CT000
1.0 ±0.3nH 8 500 10.0 16.5 0.4 0.20 250 MLG0402P1N0ST000
1.1 ±0.1nH 8500 10.0 15.0 0.5 0.22 250 MLG0402P1N1BT000
1.1 ±0.2nH 8 500 10.0 15.0 0.5 0.22 250 MLG0402P1N1CT000
1.1 ±0.3nH 8500 10.0 15.0 0.5 0.22 250 MLG0402P1N1ST000
1.2 ±0.1nH 8 500 10.0 14.8 0.5 0.25 250 MLG0402P1N2BT000
1.2 ±0.2nH 8500 10.0 14.8 0.5 0.25 250 MLG0402P1N2CT000
1.2 ±0.3nH 8 500 10.0 14.8 0.5 0.25 250 MLG0402P1N2ST000
1.3 ±0.1nH 8500 10.0 15.9 0.6 0.28 250 MLG0402P1N3BT000
1.3 ±0.2nH 8 500 10.0 15.9 0.6 0.28 250 MLG0402P1N3CT000
1.3 ±0.3nH 8500 10.0 15.9 0.6 0.28 250 MLG0402P1N3ST000
1.4 ±0.1nH 7 500 10.0 14.0 0.6 0.30 250 MLG0402P1N4BT000
1.4 ±0.2nH 7500 10.0 14.0 0.6 0.30 250 MLG0402P1N4CT000
1.4 ±0.3nH 7 500 10.0 14.0 0.6 0.30 250 MLG0402P1N4ST000
1.5 ±0.1nH 8500 10.0 14.0 0.6 0.37 220 MLG0402P1N5BT000
1.5 ±0.2nH 8 500 10.0 14.0 0.6 0.37 220 MLG0402P1N5CT000
1.5 ±0.3nH 8500 10.0 14.0 0.6 0.37 220 MLG0402P1N5ST000
1.6 ±0.1nH 9 500 9.0 12.9 0.6 0.25 220 MLG0402P1N6BT000
1.6 ±0.2nH 9500 9.0 12.9 0.6 0.25 220 MLG0402P1N6CT000
1.6 ±0.3nH 9 500 9.0 12.9 0.6 0.25 220 MLG0402P1N6ST000
1.7 ±0.1nH 9500 9.0 12.4 0.6 0.25 200 MLG0402P1N7BT000
1.7 ±0.2nH 9 500 9.0 12.4 0.6 0.25 200 MLG0402P1N7CT000
1.7 ±0.3nH 9500 9.0 12.4 0.6 0.25 200 MLG0402P1N7ST000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(7/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Short bar residual inductance =0.11nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
1.8 ±0.1nH 9 500 8.0 11.5 0.6 0.28 200 MLG0402P1N8BT000
1.8 ±0.2nH 9500 8.0 11.5 0.6 0.28 200 MLG0402P1N8CT000
1.8 ±0.3nH 9 500 8.0 11.5 0.6 0.28 200 MLG0402P1N8ST000
1.9 ±0.1nH 9500 8.0 10.5 0.6 0.27 200 MLG0402P1N9BT000
1.9 ±0.2nH 9 500 8.0 10.5 0.6 0.27 200 MLG0402P1N9CT000
1.9 ±0.3nH 9500 8.0 10.5 0.6 0.27 200 MLG0402P1N9ST000
2.0 ±0.1nH 9 500 8.0 11.0 0.6 0.30 200 MLG0402P2N0BT000
2.0 ±0.2nH 9500 8.0 11.0 0.6 0.30 200 MLG0402P2N0CT000
2.0 ±0.3nH 9 500 8.0 11.0 0.6 0.30 200 MLG0402P2N0ST000
2.1 ±0.1nH 8500 8.0 11.5 0.7 0.36 200 MLG0402P2N1BT000
2.1 ±0.2nH 8 500 8.0 11.5 0.7 0.36 200 MLG0402P2N1CT000
2.1 ±0.3nH 8500 8.0 11.5 0.7 0.36 200 MLG0402P2N1ST000
2.2 ±0.1nH 8 500 8.0 10.7 0.7 0.43 200 MLG0402P2N2BT000
2.2 ±0.2nH 8500 8.0 10.7 0.7 0.43 200 MLG0402P2N2CT000
2.2 ±0.3nH 8 500 8.0 10.7 0.7 0.43 200 MLG0402P2N2ST000
2.3 ±0.1nH 8500 7.0 10.3 0.7 0.46 200 MLG0402P2N3BT000
2.3 ±0.2nH 8 500 7.0 10.3 0.7 0.46 200 MLG0402P2N3CT000
2.3 ±0.3nH 8500 7.0 10.3 0.7 0.46 200 MLG0402P2N3ST000
2.4 ±0.1nH 8 500 7.0 10.2 0.7 0.43 200 MLG0402P2N4BT000
2.4 ±0.2nH 8500 7.0 10.2 0.7 0.43 200 MLG0402P2N4CT000
2.4 ±0.3nH 8 500 7.0 10.2 0.7 0.43 200 MLG0402P2N4ST000
2.5 ±0.1nH 8500 7.0 10.3 0.8 0.54 200 MLG0402P2N5BT000
2.5 ±0.2nH 8 500 7.0 10.3 0.8 0.54 200 MLG0402P2N5CT000
2.5 ±0.3nH 8500 7.0 10.3 0.8 0.54 200 MLG0402P2N5ST000
2.6 ±0.1nH 8 500 7.0 9.7 0.8 0.54 200 MLG0402P2N6BT000
2.6 ±0.2nH 8500 7.0 9.7 0.8 0.54 200 MLG0402P2N6CT000
2.6 ±0.3nH 8 500 7.0 9.7 0.8 0.54 200 MLG0402P2N6ST000
2.7 ±0.1nH 8500 7.0 9.9 0.8 0.54 200 MLG0402P2N7BT000
2.7 ±0.2nH 8 500 7.0 9.9 0.8 0.54 200 MLG0402P2N7CT000
2.7 ±0.3nH 8500 7.0 9.9 0.8 0.54 200 MLG0402P2N7ST000
2.8 ±0.1nH 8 500 7.0 9.2 0.8 0.52 200 MLG0402P2N8BT000
2.8 ±0.2nH 8500 7.0 9.2 0.8 0.52 200 MLG0402P2N8CT000
2.8 ±0.3nH 8 500 7.0 9.2 0.8 0.52 200 MLG0402P2N8ST000
2.9 ±0.1nH 8500 7.0 9.6 0.8 0.45 200 MLG0402P2N9BT000
2.9 ±0.2nH 8 500 7.0 9.6 0.8 0.45 200 MLG0402P2N9CT000
2.9 ±0.3nH 8500 7.0 9.6 0.8 0.45 200 MLG0402P2N9ST000
3.0 ±0.1nH 8 500 7.0 9.2 0.9 0.58 200 MLG0402P3N0BT000
3.0 ±0.2nH 8500 7.0 9.2 0.9 0.58 200 MLG0402P3N0CT000
3.0 ±0.3nH 8 500 7.0 9.2 0.9 0.58 200 MLG0402P3N0ST000
3.1 ±0.1nH 8500 7.0 9.2 1.0 0.66 200 MLG0402P3N1BT000
3.1 ±0.2nH 8 500 7.0 9.2 1.0 0.66 200 MLG0402P3N1CT000
3.1 ±0.3nH 8500 7.0 9.2 1.0 0.66 200 MLG0402P3N1ST000
3.2 ±0.1nH 8 500 7.0 9.1 1.1 0.73 180 MLG0402P3N2BT000
3.2 ±0.2nH 8500 7.0 9.1 1.1 0.73 180 MLG0402P3N2CT000
3.2 ±0.3nH 8 500 7.0 9.1 1.1 0.73 180 MLG0402P3N2ST000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(8/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Short bar residual inductance =0.11nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
3.3 ±0.1nH 8 500 6.5 8.6 1.1 0.73 180 MLG0402P3N3BT000
3.3 ±0.2nH 8500 6.5 8.6 1.1 0.73 180 MLG0402P3N3CT000
3.3 ±0.3nH 8 500 6.5 8.6 1.1 0.73 180 MLG0402P3N3ST000
3.4 ±0.1nH 8500 6.0 8.6 1.1 0.74 180 MLG0402P3N4BT000
3.4 ±0.2nH 8 500 6.0 8.6 1.1 0.74 180 MLG0402P3N4CT000
3.4 ±0.3nH 8500 6.0 8.6 1.1 0.74 180 MLG0402P3N4ST000
3.5 ±0.1nH 8 500 6.0 8.3 1.1 0.75 180 MLG0402P3N5BT000
3.5 ±0.2nH 8500 6.0 8.3 1.1 0.75 180 MLG0402P3N5CT000
3.5 ±0.3nH 8 500 6.0 8.3 1.1 0.75 180 MLG0402P3N5ST000
3.6 ±0.1nH 8500 6.0 8.3 1.1 0.73 180 MLG0402P3N6BT000
3.6 ±0.2nH 8 500 6.0 8.3 1.1 0.73 180 MLG0402P3N6CT000
3.6 ±0.3nH 8500 6.0 8.3 1.1 0.73 180 MLG0402P3N6ST000
3.7 ±0.1nH 8 500 6.0 8.0 1.1 0.70 180 MLG0402P3N7BT000
3.7 ±0.2nH 8500 6.0 8.0 1.1 0.70 180 MLG0402P3N7CT000
3.7 ±0.3nH 8 500 6.0 8.0 1.1 0.70 180 MLG0402P3N7ST000
3.8 ±0.1nH 8500 6.0 7.8 1.2 0.77 180 MLG0402P3N8BT000
3.8 ±0.2nH 8 500 6.0 7.8 1.2 0.77 180 MLG0402P3N8CT000
3.8 ±0.3nH 8500 6.0 7.8 1.2 0.77 180 MLG0402P3N8ST000
3.9 ±0.1nH 8 500 6.0 7.6 1.2 0.71 180 MLG0402P3N9BT000
3.9 ±0.2nH 8500 6.0 7.6 1.2 0.71 180 MLG0402P3N9CT000
3.9 ±0.3nH 8 500 6.0 7.6 1.2 0.71 180 MLG0402P3N9ST000
4.0 ±0.1nH 8500 6.0 7.5 1.2 0.73 180 MLG0402P4N0BT000
4.0 ±0.2nH 8 500 6.0 7.5 1.2 0.73 180 MLG0402P4N0CT000
4.0 ±0.3nH 8500 6.0 7.5 1.2 0.73 180 MLG0402P4N0ST000
4.1 ±0.1nH 8 500 6.0 7.9 1.2 0.75 180 MLG0402P4N1BT000
4.1 ±0.2nH 8500 6.0 7.9 1.2 0.75 180 MLG0402P4N1CT000
4.1 ±0.3nH 8 500 6.0 7.9 1.2 0.75 180 MLG0402P4N1ST000
4.2 ±0.1nH 8500 6.0 7.9 1.2 0.77 180 MLG0402P4N2BT000
4.2 ±0.2nH 8 500 6.0 7.9 1.2 0.77 180 MLG0402P4N2CT000
4.2 ±0.3nH 8500 6.0 7.9 1.2 0.77 180 MLG0402P4N2ST000
4.3 ±0.3nH 8 500 6.0 8.0 1.2 0.80 180 MLG0402P4N3ST000
4.3 ±3% 8500 6.0 8.0 1.2 0.80 180 MLG0402P4N3HT000
4.3 ±5% 8 500 6.0 8.0 1.2 0.80 180 MLG0402P4N3JT000
4.7 ±0.3nH 8500 5.0 7.2 1.3 0.88 160 MLG0402P4N7ST000
4.7 ±3% 8 500 5.0 7.2 1.3 0.88 160 MLG0402P4N7HT000
4.7 ±5% 8500 5.0 7.2 1.3 0.88 160 MLG0402P4N7JT000
5.1 ±0.3nH 8 500 5.0 7.0 1.4 0.90 160 MLG0402P5N1ST000
5.1 ±3% 8500 5.0 7.0 1.4 0.90 160 MLG0402P5N1HT000
5.1 ±5% 8 500 5.0 7.0 1.4 0.90 160 MLG0402P5N1JT000
5.6 ±0.3nH 8500 5.0 6.8 1.5 1.02 140 MLG0402P5N6ST000
5.6 ±3% 8 500 5.0 6.8 1.5 1.02 140 MLG0402P5N6HT000
5.6 ±5% 8500 5.0 6.8 1.5 1.02 140 MLG0402P5N6JT000
6.2 ±3% 8 500 4.5 6.5 1.5 1.04 140 MLG0402P6N2HT000
6.2 ±5% 8500 4.5 6.5 1.5 1.04 140 MLG0402P6N2JT000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(9/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Short bar residual inductance =0.11nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
6.8 ±3% 8 500 4.3 5.8 1.6 1.12 140 MLG0402P6N8HT000
6.8 ±5% 8500 4.3 5.8 1.6 1.12 140 MLG0402P6N8JT000
7.5 ±3% 8 500 4.2 5.7 1.7 1.13 140 MLG0402P7N5HT000
7.5 ±5% 8500 4.2 5.7 1.7 1.13 140 MLG0402P7N5JT000
8.2 ±3% 8 500 4.0 5.5 1.8 1.16 140 MLG0402P8N2HT000
8.2 ±5% 8500 4.0 5.5 1.8 1.16 140 MLG0402P8N2JT000
9.1 ±3% 8 500 4.0 5.5 1.8 1.20 140 MLG0402P9N1HT000
9.1 ±5% 8500 4.0 5.5 1.8 1.20 140 MLG0402P9N1JT000
10.0 ±3% 8 500 3.6 4.7 2.1 1.45 140 MLG0402P10NHT000
10.0 ±5% 8500 3.6 4.7 2.1 1.45 140 MLG0402P10NJT000
11.0 ±3% 8 500 3.5 4.6 2.2 1.51 140 MLG0402P11NHT000
11.0 ±5% 8500 3.5 4.6 2.2 1.51 140 MLG0402P11NJT000
12.0 ±3% 8 500 3.4 4.5 2.4 1.64 140 MLG0402P12NHT000
12.0 ±5% 8500 3.4 4.5 2.4 1.64 140 MLG0402P12NJT000
13.0 ±3% 8 500 3.2 4.3 2.5 1.71 140 MLG0402P13NHT000
13.0 ±5% 8500 3.2 4.3 2.5 1.71 140 MLG0402P13NJT000
15.0 ±3% 8 500 3.0 3.9 2.6 1.77 140 MLG0402P15NHT000
15.0 ±5% 8500 3.0 3.9 2.6 1.77 140 MLG0402P15NJT000
16.0 ±3% 7 500 2.4 3.4 2.7 1.79 140 MLG0402P16NHT000
16.0 ±5% 7500 2.4 3.4 2.7 1.79 140 MLG0402P16NJT000
18.0 ±3% 7 500 2.3 3.2 2.8 1.94 140 MLG0402P18NHT000
18.0 ±5% 7500 2.3 3.2 2.8 1.94 140 MLG0402P18NJT000
20.0 ±3% 7 500 2.2 2.8 3.0 2.09 130 MLG0402P20NHT000
20.0 ±5% 7500 2.2 2.8 3.0 2.09 130 MLG0402P20NJT000
22.0 ±3% 7 500 2.0 2.7 3.2 2.18 130 MLG0402P22NHT000
22.0 ±5% 7500 2.0 2.7 3.2 2.18 130 MLG0402P22NJT000
24.0 ±3% 7 500 2.0 2.6 3.2 2.30 120 MLG0402P24NHT000
24.0 ±5% 7500 2.0 2.6 3.2 2.30 120 MLG0402P24NJT000
27.0 ±3% 7 500 1.8 2.3 3.5 2.44 120 MLG0402P27NHT000
27.0 ±5% 7500 1.8 2.3 3.5 2.44 120 MLG0402P27NJT000
30.0 ±3% 7 500 1.7 2.2 3.6 2.56 120 MLG0402P30NHT000
30.0 ±5% 7500 1.7 2.2 3.6 2.56 120 MLG0402P30NJT000
33.0 ±3% 6 300 1.4 1.9 3.8 2.71 120 MLG0402P33NHT000
33.0 ±5% 6300 1.4 1.9 3.8 2.71 120 MLG0402P33NJT000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(10/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.2 0.2 0.2 0.2 0.2 12 15 23 25 29 MLG0402P0N2BT000
0.2 0.2 0.2 0.2 0.2 12 15 23 25 29 MLG0402P0N2CT000
0.3 0.3 0.3 0.3 0.3 17 22 35 39 44 MLG0402P0N3BT000
0.3 0.3 0.3 0.3 0.3 17 22 35 39 44 MLG0402P0N3CT000
0.4 0.4 0.4 0.4 0.4 12 15 22 24 26 MLG0402P0N4BT000
0.4 0.4 0.4 0.4 0.4 12 15 22 24 26 MLG0402P0N4CT000
0.4 0.4 0.4 0.4 0.4 12 15 22 24 26 MLG0402P0N4ST000
0.5 0.5 0.5 0.5 0.5 12 16 25 27 30 MLG0402P0N5BT000
0.5 0.5 0.5 0.5 0.5 12 16 25 27 30 MLG0402P0N5CT000
0.5 0.5 0.5 0.5 0.5 12 16 25 27 30 MLG0402P0N5ST000
0.6 0.6 0.6 0.6 0.6 11 15 23 26 29 MLG0402P0N6BT000
0.6 0.6 0.6 0.6 0.6 11 15 23 26 29 MLG0402P0N6CT000
0.6 0.6 0.6 0.6 0.6 11 15 23 26 29 MLG0402P0N6ST000
0.7 0.7 0.7 0.7 0.7 10 14 22 25 28 MLG0402P0N7BT000
0.7 0.7 0.7 0.7 0.7 10 14 22 25 28 MLG0402P0N7CT000
0.7 0.7 0.7 0.7 0.7 10 14 22 25 28 MLG0402P0N7ST000
0.8 0.8 0.8 0.8 0.8 12 15 23 25 27 MLG0402P0N8BT000
0.8 0.8 0.8 0.8 0.8 12 15 23 25 27 MLG0402P0N8CT000
0.8 0.8 0.8 0.8 0.8 12 15 23 25 27 MLG0402P0N8ST000
0.9 0.9 0.9 0.9 0.9 12 15 23 25 27 MLG0402P0N9BT000
0.9 0.9 0.9 0.9 0.9 12 15 23 25 27 MLG0402P0N9CT000
0.9 0.9 0.9 0.9 0.9 12 15 23 25 27 MLG0402P0N9ST000
1.0 1.0 1.0 1.0 1.0 12 16 24 26 29 MLG0402P1N0BT000
1.0 1.0 1.0 1.0 1.0 12 16 24 26 29 MLG0402P1N0CT000
1.0 1.0 1.0 1.0 1.0 12 16 24 26 29 MLG0402P1N0ST000
1.1 1.1 1.1 1.1 1.1 12 15 23 25 28 MLG0402P1N1BT000
1.1 1.1 1.1 1.1 1.1 12 15 23 25 28 MLG0402P1N1CT000
1.1 1.1 1.1 1.1 1.1 12 15 23 25 28 MLG0402P1N1ST000
1.2 1.2 1.2 1.2 1.2 12 15 23 25 27 MLG0402P1N2BT000
1.2 1.2 1.2 1.2 1.2 12 15 23 25 27 MLG0402P1N2CT000
1.2 1.2 1.2 1.2 1.2 12 15 23 25 27 MLG0402P1N2ST000
1.3 1.3 1.3 1.3 1.3 11 14 23 25 28 MLG0402P1N3BT000
1.3 1.3 1.3 1.3 1.3 11 14 23 25 28 MLG0402P1N3CT000
1.3 1.3 1.3 1.3 1.3 11 14 23 25 28 MLG0402P1N3ST000
1.4 1.4 1.4 1.4 1.4 9 12 20 21 24 MLG0402P1N4BT000
1.4 1.4 1.4 1.4 1.4 912 20 21 24 MLG0402P1N4CT000
1.4 1.4 1.4 1.4 1.4 9 12 20 21 24 MLG0402P1N4ST000
1.5 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402P1N5BT000
1.5 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402P1N5CT000
1.5 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402P1N5ST000
1.6 1.6 1.6 1.6 1.6 12 15 24 26 29 MLG0402P1N6BT000
1.6 1.6 1.6 1.6 1.6 12 15 24 26 29 MLG0402P1N6CT000
1.6 1.6 1.6 1.6 1.6 12 15 24 26 29 MLG0402P1N6ST000
1.7 1.7 1.7 1.7 1.7 12 15 23 25 28 MLG0402P1N7BT000
1.7 1.7 1.7 1.7 1.7 12 15 23 25 28 MLG0402P1N7CT000
1.7 1.7 1.7 1.7 1.7 12 15 23 25 28 MLG0402P1N7ST000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(11/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
1.8 1.8 1.8 1.8 1.8 12 15 24 26 28 MLG0402P1N8BT000
1.8 1.8 1.8 1.8 1.8 12 15 24 26 28 MLG0402P1N8CT000
1.8 1.8 1.8 1.8 1.8 12 15 24 26 28 MLG0402P1N8ST000
1.9 1.9 1.9 1.9 1.9 11 15 23 24 27 MLG0402P1N9BT000
1.9 1.9 1.9 1.9 1.9 11 15 23 24 27 MLG0402P1N9CT000
1.9 1.9 1.9 1.9 1.9 11 15 23 24 27 MLG0402P1N9ST000
2.0 2.0 2.0 2.0 2.0 12 15 24 26 28 MLG0402P2N0BT000
2.0 2.0 2.0 2.0 2.0 12 15 24 26 28 MLG0402P2N0CT000
2.0 2.0 2.0 2.0 2.0 12 15 24 26 28 MLG0402P2N0ST000
2.1 2.1 2.1 2.1 2.1 12 15 24 26 29 MLG0402P2N1BT000
2.1 2.1 2.1 2.1 2.1 12 15 24 26 29 MLG0402P2N1CT000
2.1 2.1 2.1 2.1 2.1 12 15 24 26 29 MLG0402P2N1ST000
2.2 2.2 2.2 2.2 2.2 11 14 23 24 27 MLG0402P2N2BT000
2.2 2.2 2.2 2.2 2.2 11 14 23 24 27 MLG0402P2N2CT000
2.2 2.2 2.2 2.2 2.2 11 14 23 24 27 MLG0402P2N2ST000
2.3 2.3 2.3 2.3 2.3 11 14 22 24 26 MLG0402P2N3BT000
2.3 2.3 2.3 2.3 2.3 11 14 22 24 26 MLG0402P2N3CT000
2.3 2.3 2.3 2.3 2.3 11 14 22 24 26 MLG0402P2N3ST000
2.4 2.4 2.4 2.4 2.4 11 14 22 24 26 MLG0402P2N4BT000
2.4 2.4 2.4 2.4 2.4 11 14 22 24 26 MLG0402P2N4CT000
2.4 2.4 2.4 2.4 2.4 11 14 22 24 26 MLG0402P2N4ST000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402P2N5BT000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402P2N5CT000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402P2N5ST000
2.6 2.6 2.6 2.6 2.6 10 13 21 23 25 MLG0402P2N6BT000
2.6 2.6 2.6 2.6 2.6 10 13 21 23 25 MLG0402P2N6CT000
2.6 2.6 2.6 2.6 2.6 10 13 21 23 25 MLG0402P2N6ST000
2.7 2.7 2.6 2.6 2.7 11 14 22 24 26 MLG0402P2N7BT000
2.7 2.7 2.6 2.6 2.7 11 14 22 24 26 MLG0402P2N7CT000
2.7 2.7 2.6 2.6 2.7 11 14 22 24 26 MLG0402P2N7ST000
2.8 2.8 2.8 2.8 2.8 11 14 21 23 25 MLG0402P2N8BT000
2.8 2.8 2.8 2.8 2.8 11 14 21 23 25 MLG0402P2N8CT000
2.8 2.8 2.8 2.8 2.8 11 14 21 23 25 MLG0402P2N8ST000
2.9 2.9 2.8 2.9 2.9 11 14 21 23 25 MLG0402P2N9BT000
2.9 2.9 2.8 2.9 2.9 11 14 21 23 25 MLG0402P2N9CT000
2.9 2.9 2.8 2.9 2.9 11 14 21 23 25 MLG0402P2N9ST000
3.0 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N0BT000
3.0 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N0CT000
3.0 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N0ST000
3.1 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N1BT000
3.1 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N1CT000
3.1 3.0 2.9 3.0 3.0 11 14 20 22 24 MLG0402P3N1ST000
3.2 3.2 3.1 3.2 3.2 10 14 21 22 25 MLG0402P3N2BT000
3.2 3.2 3.1 3.2 3.2 10 14 21 22 25 MLG0402P3N2CT000
3.2 3.2 3.1 3.2 3.2 10 14 21 22 25 MLG0402P3N2ST000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(12/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
3.3 3.3 3.3 3.3 3.3 10 13 21 22 24 MLG0402P3N3BT000
3.3 3.3 3.3 3.3 3.3 10 13 21 22 24 MLG0402P3N3CT000
3.3 3.3 3.3 3.3 3.3 10 13 21 22 24 MLG0402P3N3ST000
3.4 3.4 3.4 3.4 3.4 10 13 20 21 23 MLG0402P3N4BT000
3.4 3.4 3.4 3.4 3.4 10 13 20 21 23 MLG0402P3N4CT000
3.4 3.4 3.4 3.4 3.4 10 13 20 21 23 MLG0402P3N4ST000
3.5 3.5 3.5 3.5 3.6 10 13 20 22 24 MLG0402P3N5BT000
3.5 3.5 3.5 3.5 3.6 10 13 20 22 24 MLG0402P3N5CT000
3.5 3.5 3.5 3.5 3.6 10 13 20 22 24 MLG0402P3N5ST000
3.6 3.6 3.6 3.6 3.6 10 13 20 21 23 MLG0402P3N6BT000
3.6 3.6 3.6 3.6 3.6 10 13 20 21 23 MLG0402P3N6CT000
3.6 3.6 3.6 3.6 3.6 10 13 20 21 23 MLG0402P3N6ST000
3.7 3.6 3.7 3.7 3.7 10 13 19 21 22 MLG0402P3N7BT000
3.7 3.6 3.7 3.7 3.7 10 13 19 21 22 MLG0402P3N7CT000
3.7 3.6 3.7 3.7 3.7 10 13 19 21 22 MLG0402P3N7ST000
3.8 3.7 3.8 3.8 3.8 10 13 20 21 23 MLG0402P3N8BT000
3.8 3.7 3.8 3.8 3.8 10 13 20 21 23 MLG0402P3N8CT000
3.8 3.7 3.8 3.8 3.8 10 13 20 21 23 MLG0402P3N8ST000
3.9 3.9 3.9 4.0 4.1 10 13 19 20 21 MLG0402P3N9BT000
3.9 3.9 3.9 4.0 4.1 10 13 19 20 21 MLG0402P3N9CT000
3.9 3.9 3.9 4.0 4.1 10 13 19 20 21 MLG0402P3N9ST000
4.0 3.9 4.0 4.0 4.1 10 12 18 19 21 MLG0402P4N0BT000
4.0 3.9 4.0 4.0 4.1 10 12 18 19 21 MLG0402P4N0CT000
4.0 3.9 4.0 4.0 4.1 10 12 18 19 21 MLG0402P4N0ST000
4.1 4.1 4.1 4.1 4.2 11 14 22 23 26 MLG0402P4N1BT000
4.1 4.1 4.1 4.1 4.2 11 14 22 23 26 MLG0402P4N1CT000
4.1 4.1 4.1 4.1 4.2 11 14 22 23 26 MLG0402P4N1ST000
4.2 4.1 4.2 4.2 4.3 11 14 21 23 25 MLG0402P4N2BT000
4.2 4.1 4.2 4.2 4.3 11 14 21 23 25 MLG0402P4N2CT000
4.2 4.1 4.2 4.2 4.3 11 14 21 23 25 MLG0402P4N2ST000
4.3 4.2 4.3 4.3 4.4 10 13 20 22 24 MLG0402P4N3ST000
4.3 4.2 4.3 4.3 4.4 10 13 20 22 24 MLG0402P4N3HT000
4.3 4.2 4.3 4.3 4.4 10 13 20 22 24 MLG0402P4N3JT000
4.7 4.6 4.7 4.8 4.9 11 14 21 22 24 MLG0402P4N7ST000
4.7 4.6 4.7 4.8 4.9 11 14 21 22 24 MLG0402P4N7HT000
4.7 4.6 4.7 4.8 4.9 11 14 21 22 24 MLG0402P4N7JT000
5.1 5.0 5.1 5.2 5.3 10 13 20 21 22 MLG0402P5N1ST000
5.1 5.0 5.1 5.2 5.3 10 13 20 21 22 MLG0402P5N1HT000
5.1 5.0 5.1 5.2 5.3 10 13 20 21 22 MLG0402P5N1JT000
5.6 5.5 5.7 5.8 5.9 11 14 21 22 24 MLG0402P5N6ST000
5.6 5.5 5.7 5.8 5.9 11 14 21 22 24 MLG0402P5N6HT000
5.6 5.5 5.7 5.8 5.9 11 14 21 22 24 MLG0402P5N6JT000
6.2 6.1 6.3 6.4 6.6 11 14 20 21 22 MLG0402P6N2HT000
6.2 6.1 6.3 6.4 6.6 11 14 20 21 22 MLG0402P6N2JT000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(13/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
6.8 6.7 6.9 7.1 7.3 11 14 20 21 23 MLG0402P6N8HT000
6.8 6.7 6.9 7.1 7.3 11 14 20 21 23 MLG0402P6N8JT000
7.5 7.4 7.7 7.8 8.1 11 14 20 21 22 MLG0402P7N5HT000
7.5 7.4 7.7 7.8 8.1 11 14 20 21 22 MLG0402P7N5JT000
8.2 8.1 8.5 8.7 9.1 11 14 20 21 22 MLG0402P8N2HT000
8.2 8.1 8.5 8.7 9.1 11 14 20 21 22 MLG0402P8N2JT000
9.1 9.0 9.5 9.8 10.3 12 15 21 22 22 MLG0402P9N1HT000
9.1 9.0 9.5 9.8 10.3 12 15 21 22 22 MLG0402P9N1JT000
10.0 10.0 10.6 10.9 11.6 11 14 20 21 22 MLG0402P10NHT000
10.0 10.0 10.6 10.9 11.6 11 14 20 21 22 MLG0402P10NJT000
11.0 11.0 11.7 12.1 12.9 11 14 19 20 20 MLG0402P11NHT000
11.0 11.0 11.7 12.1 12.9 11 14 19 20 20 MLG0402P11NJT000
12.0 12.0 13.1 13.6 14.9 11 14 18 19 19 MLG0402P12NHT000
12.0 12.0 13.1 13.6 14.9 11 14 18 19 19 MLG0402P12NJT000
13.0 13.0 14.3 15.0 16.6 11 14 18 18 18 MLG0402P13NHT000
13.0 13.0 14.3 15.0 16.6 11 14 18 18 18 MLG0402P13NJT000
15.0 15.0 16.6 17.4 19.3 11 14 17 18 17 MLG0402P15NHT000
15.0 15.0 16.6 17.4 19.3 11 14 17 18 17 MLG0402P15NJT000
16.0 16.2 19.3 21.1 25.5 11 13 16 16 14 MLG0402P16NHT000
16.0 16.2 19.3 21.1 25.5 11 13 16 16 14 MLG0402P16NJT000
18.0 18.3 22.6 25.1 31.8 11 13 15 15 12 MLG0402P18NHT000
18.0 18.3 22.6 25.1 31.8 11 13 15 15 12 MLG0402P18NJT000
20.0 20.4 26.1 29.6 11 13 14 13 MLG0402P20NHT000
20.0 20.4 26.1 29.6 11 13 14 13 MLG0402P20NJT000
22.0 22.6 30.2 35.3 10 12 13 12 MLG0402P22NHT000
22.0 22.6 30.2 35.3 10 12 13 12 MLG0402P22NJT000
24.0 24.7 34.9 10 12 11 MLG0402P24NHT000
24.0 24.7 34.9 10 12 11 MLG0402P24NJT000
27.0 28.0 41.8 10 12 11 MLG0402P27NHT000
27.0 28.0 41.8 10 12 11 MLG0402P27NJT000
30.0 31.7 10 11 MLG0402P30NHT000
30.0 31.7 10 11 MLG0402P30NJT000
33.0 35.0 10 12 MLG0402P33NHT000
33.0 35.0 10 12 MLG0402P33NJT000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(14/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
33N
27N 22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A+16196D Agilent Technologies
(15/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0402P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
60
50
Q
10 100 1000 10000
Frequency(MHz)
33N 27N
22N
18N
15N
12N
6N8
5N6
3N9
3N3
2N7
1N8
1N5
1N0
1N2
4N7
8N2
10N
2N2
Product No. Manufacturer
E4991A+16196D Agilent Technologies
(16/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries
MLG0402Q Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.40±0.02
0.11±0.03 0.11±0.03
0.20±0.02 0.20±0.02
Dimensions in mm
0.18 to 0.20
0.15 to 0.2
0.2
0.15 to 0.2
(17/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
0.2 ±0.1nH — 100 10.0 20.0 0.10 0.03 350 MLG0402Q0N2BT000
0.2 ±0.2nH —100 10.0 20.0 0.10 0.03 350 MLG0402Q0N2CT000
0.3 ±0.1nH — 100 10.0 18.5 0.20 0.07 350 MLG0402Q0N3BT000
0.3 ±0.2nH —100 10.0 18.5 0.20 0.07 350 MLG0402Q0N3CT000
0.4 ±0.1nH — 100 10.0 20.0 0.20 0.08 350 MLG0402Q0N4BT000
0.4 ±0.2nH —100 10.0 20.0 0.20 0.08 350 MLG0402Q0N4CT000
0.5 ±0.1nH — 100 10.0 20.0 0.20 0.11 350 MLG0402Q0N5BT000
0.5 ±0.2nH —100 10.0 20.0 0.20 0.11 350 MLG0402Q0N5CT000
0.6 ±0.1nH — 100 10.0 20.0 0.30 0.13 320 MLG0402Q0N6BT000
0.6 ±0.2nH —100 10.0 20.0 0.30 0.13 320 MLG0402Q0N6CT000
0.7 ±0.1nH — 100 10.0 20.0 0.40 0.19 320 MLG0402Q0N7BT000
0.7 ±0.2nH —100 10.0 20.0 0.40 0.19 320 MLG0402Q0N7CT000
0.8 ±0.1nH — 100 10.0 19.5 0.40 0.11 320 MLG0402Q0N8BT000
0.8 ±0.2nH —100 10.0 19.5 0.40 0.11 320 MLG0402Q0N8CT000
0.9 ±0.1nH — 100 10.0 20.0 0.40 0.15 320 MLG0402Q0N9BT000
0.9 ±0.2nH —100 10.0 20.0 0.40 0.15 320 MLG0402Q0N9CT000
1.0 ±0.1nH 2 100 10.0 16.8 0.40 0.20 250 MLG0402Q1N0BT000
1.0 ±0.2nH 2100 10.0 16.8 0.40 0.20 250 MLG0402Q1N0CT000
1.0 ±0.3nH 2 100 10.0 16.8 0.40 0.20 250 MLG0402Q1N0ST000
1.1 ±0.1nH 2100 10.0 16.6 0.50 0.22 250 MLG0402Q1N1BT000
1.1 ±0.2nH 2 100 10.0 16.6 0.50 0.22 250 MLG0402Q1N1CT000
1.1 ±0.3nH 2100 10.0 16.6 0.50 0.22 250 MLG0402Q1N1ST000
1.2 ±0.1nH 2 100 10.0 16.2 0.50 0.25 250 MLG0402Q1N2BT000
1.2 ±0.2nH 2100 10.0 16.2 0.50 0.25 250 MLG0402Q1N2CT000
1.2 ±0.3nH 2 100 10.0 16.2 0.50 0.25 250 MLG0402Q1N2ST000
1.3 ±0.1nH 2100 10.0 16.0 0.60 0.28 250 MLG0402Q1N3BT000
1.3 ±0.2nH 2 100 10.0 16.0 0.60 0.28 250 MLG0402Q1N3CT000
1.3 ±0.3nH 2100 10.0 16.0 0.60 0.28 250 MLG0402Q1N3ST000
1.4 ±0.1nH 2 100 10.0 15.8 0.60 0.30 250 MLG0402Q1N4BT000
1.4 ±0.2nH 2100 10.0 15.8 0.60 0.30 250 MLG0402Q1N4CT000
1.4 ±0.3nH 2 100 10.0 15.8 0.60 0.30 250 MLG0402Q1N4ST000
1.5 ±0.1nH 2100 10.0 15.6 0.60 0.37 220 MLG0402Q1N5BT000
1.5 ±0.2nH 2 100 10.0 15.6 0.60 0.37 220 MLG0402Q1N5CT000
1.5 ±0.3nH 2100 10.0 15.6 0.60 0.37 220 MLG0402Q1N5ST000
1.6 ±0.1nH 2 100 10.0 14.4 0.60 0.25 220 MLG0402Q1N6BT000
1.6 ±0.2nH 2100 10.0 14.4 0.60 0.25 220 MLG0402Q1N6CT000
1.6 ±0.3nH 2 100 10.0 14.4 0.60 0.25 220 MLG0402Q1N6ST000
1.7 ±0.1nH 2100 10.0 13.4 0.60 0.25 200 MLG0402Q1N7BT000
1.7 ±0.2nH 2 100 10.0 13.4 0.60 0.25 200 MLG0402Q1N7CT000
1.7 ±0.3nH 2100 10.0 13.4 0.60 0.25 200 MLG0402Q1N7ST000
1.8 ±0.1nH 2 100 10.0 13.9 0.60 0.28 200 MLG0402Q1N8BT000
1.8 ±0.2nH 2100 10.0 13.9 0.60 0.28 200 MLG0402Q1N8CT000
1.8 ±0.3nH 2 100 10.0 13.9 0.60 0.28 200 MLG0402Q1N8ST000
1.9 ±0.1nH 2100 9.0 12.2 0.60 0.27 200 MLG0402Q1N9BT000
1.9 ±0.2nH 2 100 9.0 12.2 0.60 0.27 200 MLG0402Q1N9CT000
1.9 ±0.3nH 2100 9.0 12.2 0.60 0.27 200 MLG0402Q1N9ST000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(18/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
2.0 ±0.1nH 2 100 9.0 12.5 0.60 0.30 200 MLG0402Q2N0BT000
2.0 ±0.2nH 2100 9.0 12.5 0.60 0.30 200 MLG0402Q2N0CT000
2.0 ±0.3nH 2 100 9.0 12.5 0.60 0.30 200 MLG0402Q2N0ST000
2.1 ±0.1nH 2100 8.0 11.8 0.70 0.36 200 MLG0402Q2N1BT000
2.1 ±0.2nH 2 100 8.0 11.8 0.70 0.36 200 MLG0402Q2N1CT000
2.1 ±0.3nH 2100 8.0 11.8 0.70 0.36 200 MLG0402Q2N1ST000
2.2 ±0.1nH 2 100 8.0 11.7 0.80 0.43 200 MLG0402Q2N2BT000
2.2 ±0.2nH 2100 8.0 11.7 0.80 0.43 200 MLG0402Q2N2CT000
2.2 ±0.3nH 2 100 8.0 11.7 0.80 0.43 200 MLG0402Q2N2ST000
2.3 ±0.1nH 2100 7.0 11.0 0.80 0.46 200 MLG0402Q2N3BT000
2.3 ±0.2nH 2 100 7.0 11.0 0.80 0.46 200 MLG0402Q2N3CT000
2.3 ±0.3nH 2100 7.0 11.0 0.80 0.46 200 MLG0402Q2N3ST000
2.4 ±0.1nH 2 100 7.0 10.9 0.80 0.43 200 MLG0402Q2N4BT000
2.4 ±0.2nH 2100 7.0 10.9 0.80 0.43 200 MLG0402Q2N4CT000
2.4 ±0.3nH 2 100 7.0 10.9 0.80 0.43 200 MLG0402Q2N4ST000
2.5 ±0.1nH 2100 7.0 10.5 0.80 0.54 200 MLG0402Q2N5BT000
2.5 ±0.2nH 2 100 7.0 10.5 0.80 0.54 200 MLG0402Q2N5CT000
2.5 ±0.3nH 2100 7.0 10.5 0.80 0.54 200 MLG0402Q2N5ST000
2.6 ±0.1nH 2 100 7.0 10.7 0.80 0.54 200 MLG0402Q2N6BT000
2.6 ±0.2nH 2100 7.0 10.7 0.80 0.54 200 MLG0402Q2N6CT000
2.6 ±0.3nH 2 100 7.0 10.7 0.80 0.54 200 MLG0402Q2N6ST000
2.7 ±0.1nH 2100 7.0 10.7 0.80 0.54 200 MLG0402Q2N7BT000
2.7 ±0.2nH 2 100 7.0 10.7 0.80 0.54 200 MLG0402Q2N7CT000
2.7 ±0.3nH 2100 7.0 10.7 0.80 0.54 200 MLG0402Q2N7ST000
2.8 ±0.1nH 2 100 7.0 10.4 0.80 0.56 200 MLG0402Q2N8BT000
2.8 ±0.2nH 2100 7.0 10.4 0.80 0.56 200 MLG0402Q2N8CT000
2.8 ±0.3nH 2 100 7.0 10.4 0.80 0.56 200 MLG0402Q2N8ST000
2.9 ±0.1nH 2100 7.0 10.0 0.80 0.52 200 MLG0402Q2N9BT000
2.9 ±0.2nH 2 100 7.0 10.0 0.80 0.52 200 MLG0402Q2N9CT000
2.9 ±0.3nH 2100 7.0 10.0 0.80 0.52 200 MLG0402Q2N9ST000
3.0 ±0.1nH 2 100 7.0 10.0 0.80 0.45 200 MLG0402Q3N0BT000
3.0 ±0.2nH 2100 7.0 10.0 0.80 0.45 200 MLG0402Q3N0CT000
3.0 ±0.3nH 2 100 7.0 10.0 0.80 0.45 200 MLG0402Q3N0ST000
3.1 ±0.1nH 2100 7.0 9.7 0.90 0.58 200 MLG0402Q3N1BT000
3.1 ±0.2nH 2 100 7.0 9.7 0.90 0.58 200 MLG0402Q3N1CT000
3.1 ±0.3nH 2100 7.0 9.7 0.90 0.58 200 MLG0402Q3N1ST000
3.2 ±0.1nH 2 100 7.0 9.4 1.00 0.66 200 MLG0402Q3N2BT000
3.2 ±0.2nH 2100 7.0 9.4 1.00 0.66 200 MLG0402Q3N2CT000
3.2 ±0.3nH 2 100 7.0 9.4 1.00 0.66 200 MLG0402Q3N2ST000
3.3 ±0.1nH 2100 7.0 10.0 1.10 0.73 180 MLG0402Q3N3BT000
3.3 ±0.2nH 2 100 7.0 10.0 1.10 0.73 180 MLG0402Q3N3CT000
3.3 ±0.3nH 2100 7.0 10.0 1.10 0.73 180 MLG0402Q3N3ST000
3.4 ±0.1nH 2 100 6.5 9.1 1.10 0.73 180 MLG0402Q3N4BT000
3.4 ±0.2nH 2100 6.5 9.1 1.10 0.73 180 MLG0402Q3N4CT000
3.4 ±0.3nH 2 100 6.5 9.1 1.10 0.73 180 MLG0402Q3N4ST000
3.5 ±0.1nH 2100 6.0 9.0 1.10 0.74 180 MLG0402Q3N5BT000
3.5 ±0.2nH 2 100 6.0 9.0 1.10 0.74 180 MLG0402Q3N5CT000
3.5 ±0.3nH 2100 6.0 9.0 1.10 0.74 180 MLG0402Q3N5ST000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(19/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
3.6 ±0.1nH 2 100 6.0 9.0 1.10 0.75 180 MLG0402Q3N6BT000
3.6 ±0.2nH 2100 6.0 9.0 1.10 0.75 180 MLG0402Q3N6CT000
3.6 ±0.3nH 2 100 6.0 9.0 1.10 0.75 180 MLG0402Q3N6ST000
3.7 ±0.1nH 2100 6.0 8.9 1.10 0.73 180 MLG0402Q3N7BT000
3.7 ±0.2nH 2 100 6.0 8.9 1.10 0.73 180 MLG0402Q3N7CT000
3.7 ±0.3nH 2100 6.0 8.9 1.10 0.73 180 MLG0402Q3N7ST000
3.8 ±0.1nH 2 100 6.0 8.4 1.10 0.70 180 MLG0402Q3N8BT000
3.8 ±0.2nH 2100 6.0 8.4 1.10 0.70 180 MLG0402Q3N8CT000
3.8 ±0.3nH 2 100 6.0 8.4 1.10 0.70 180 MLG0402Q3N8ST000
3.9 ±0.1nH 2100 6.0 8.8 1.20 0.77 180 MLG0402Q3N9BT000
3.9 ±0.2nH 2 100 6.0 8.8 1.20 0.77 180 MLG0402Q3N9CT000
3.9 ±0.3nH 2100 6.0 8.8 1.20 0.77 180 MLG0402Q3N9ST000
4.0 ±0.1nH 2 100 6.0 8.4 1.20 0.71 180 MLG0402Q4N0BT000
4.0 ±0.2nH 2100 6.0 8.4 1.20 0.71 180 MLG0402Q4N0CT000
4.0 ±0.3nH 2 100 6.0 8.4 1.20 0.71 180 MLG0402Q4N0ST000
4.3 ±0.3nH 2100 6.0 8.6 1.20 0.77 180 MLG0402Q4N3ST000
4.3 ±3% 2 100 6.0 8.6 1.20 0.77 180 MLG0402Q4N3HT000
4.7 ±0.3nH 2100 6.0 8.1 1.30 0.88 160 MLG0402Q4N7ST000
4.7 ±3% 2 100 6.0 8.1 1.30 0.88 160 MLG0402Q4N7HT000
5.1 ±0.3nH 2100 6.0 7.8 1.40 0.90 160 MLG0402Q5N1ST000
5.1 ±3% 2 100 6.0 7.8 1.40 0.90 160 MLG0402Q5N1HT000
5.6 ±0.3nH 2100 6.0 7.8 1.50 1.02 140 MLG0402Q5N6ST000
5.6 ±3% 2 100 6.0 7.8 1.50 1.02 140 MLG0402Q5N6HT000
6.2 ±0.3nH 2100 5.5 7.2 1.50 1.04 140 MLG0402Q6N2ST000
6.2 ±3% 2 100 5.5 7.2 1.50 1.04 140 MLG0402Q6N2HT000
6.8 ±3% 2100 5.5 6.9 1.60 1.12 140 MLG0402Q6N8HT000
6.8 ±5% 2 100 5.5 6.9 1.60 1.12 140 MLG0402Q6N8JT000
7.5 ±3% 2100 5.0 6.7 1.70 1.13 140 MLG0402Q7N5HT000
7.5 ±5% 2 100 5.0 6.7 1.70 1.13 140 MLG0402Q7N5JT000
8.2 ±3% 2100 4.5 6.2 1.80 1.16 140 MLG0402Q8N2HT000
8.2 ±5% 2 100 4.5 6.2 1.80 1.16 140 MLG0402Q8N2JT000
9.1 ±3% 2100 4.0 5.7 1.80 1.20 140 MLG0402Q9N1HT000
9.1 ±5% 2 100 4.0 5.7 1.80 1.20 140 MLG0402Q9N1JT000
10.0 ±3% 3100 4.0 5.3 2.10 1.45 140 MLG0402Q10NHT000
10.0 ±5% 3 100 4.0 5.3 2.10 1.45 140 MLG0402Q10NJT000
12.0 ±3% 3100 3.5 4.8 2.40 1.64 140 MLG0402Q12NHT000
12.0 ±5% 3 100 3.5 4.8 2.40 1.64 140 MLG0402Q12NJT000
15.0 ±3% 3100 3.0 4.5 2.60 1.77 140 MLG0402Q15NHT000
15.0 ±5% 3 100 3.0 4.5 2.60 1.77 140 MLG0402Q15NJT000
18.0 ±3% 3100 2.5 3.0 2.80 1.94 140 MLG0402Q18NHT000
18.0 ±5% 3 100 2.5 3.0 2.80 1.94 140 MLG0402Q18NJT000
22.0 ±3% 3100 2.2 2.7 3.20 2.18 130 MLG0402Q22NHT000
22.0 ±5% 3 100 2.2 2.7 3.20 2.18 130 MLG0402Q22NJT000
27.0 ±3% 3100 1.9 2.5 3.50 2.44 120 MLG0402Q27NHT000
27.0 ±5% 3 100 1.9 2.5 3.50 2.44 120 MLG0402Q27NJT000
33.0 ±3% 3100 1.7 2.2 3.80 2.71 120 MLG0402Q33NHT000
33.0 ±5% 3 100 1.7 2.2 3.80 2.71 120 MLG0402Q33NJT000
Measurement item Product No. Manufacturer
L, Q 4291B+16196D Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance 4338A Agilent Technologies
(20/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.2 0.2 0.2 0.2 0.2 8 11 18 20 23 MLG0402Q0N2BT000
0.2 0.2 0.2 0.2 0.2 811 18 20 23 MLG0402Q0N2CT000
0.3 0.3 0.3 0.3 0.3 7 9 15 16 19 MLG0402Q0N3BT000
0.3 0.3 0.3 0.3 0.3 7 9 15 16 19 MLG0402Q0N3CT000
0.4 0.4 0.4 0.4 0.3 9 12 19 20 22 MLG0402Q0N4BT000
0.4 0.4 0.4 0.4 0.3 912 19 20 22 MLG0402Q0N4CT000
0.5 0.5 0.4 0.4 0.4 9 12 19 21 23 MLG0402Q0N5BT000
0.5 0.5 0.4 0.4 0.4 912 19 21 23 MLG0402Q0N5CT000
0.6 0.5 0.5 0.5 0.5 7 11 17 18 20 MLG0402Q0N6BT000
0.6 0.5 0.5 0.5 0.5 711 17 18 20 MLG0402Q0N6CT000
0.7 0.7 0.6 0.6 0.6 8 11 18 19 22 MLG0402Q0N7BT000
0.7 0.7 0.7 0.7 0.7 912 20 21 24 MLG0402Q0N8BT000
0.7 0.7 0.6 0.6 0.6 8 11 18 19 22 MLG0402Q0N7CT000
0.7 0.7 0.7 0.7 0.7 912 20 21 24 MLG0402Q0N8CT000
0.8 0.8 0.8 0.8 0.8 10 13 21 23 26 MLG0402Q0N9BT000
0.8 0.8 0.8 0.8 0.8 10 13 21 23 26 MLG0402Q0N9CT000
0.9 0.9 0.9 0.9 0.9 10 12 20 22 25 MLG0402Q1N0BT000
0.9 0.9 0.9 0.9 0.9 10 12 20 22 25 MLG0402Q1N0CT000
0.9 0.9 0.9 0.9 0.9 10 12 20 22 25 MLG0402Q1N0ST000
1.0 1.0 1.0 1.0 1.0 912 20 22 25 MLG0402Q1N1BT000
1.0 1.0 1.0 1.0 1.0 9 12 20 22 25 MLG0402Q1N1CT000
1.0 1.0 1.0 1.0 1.0 912 20 22 25 MLG0402Q1N1ST000
1.1 1.1 1.1 1.1 1.1 9 12 20 21 24 MLG0402Q1N2BT000
1.1 1.1 1.1 1.1 1.1 912 20 21 24 MLG0402Q1N2CT000
1.1 1.1 1.1 1.1 1.1 9 12 20 21 24 MLG0402Q1N2ST000
1.2 1.2 1.2 1.2 1.2 912 20 22 25 MLG0402Q1N3BT000
1.2 1.2 1.2 1.2 1.2 9 12 20 22 25 MLG0402Q1N3CT000
1.2 1.2 1.2 1.2 1.2 912 20 22 25 MLG0402Q1N3ST000
1.3 1.3 1.3 1.3 1.3 9 12 20 22 25 MLG0402Q1N4BT000
1.3 1.3 1.3 1.3 1.3 912 20 22 25 MLG0402Q1N4CT000
1.3 1.3 1.3 1.3 1.3 9 12 20 22 25 MLG0402Q1N4ST000
1.4 1.4 1.4 1.4 1.4 912 19 21 23 MLG0402Q1N5BT000
1.4 1.4 1.4 1.4 1.4 9 12 19 21 23 MLG0402Q1N5CT000
1.4 1.4 1.4 1.4 1.4 912 19 21 23 MLG0402Q1N5ST000
1.5 1.5 1.4 1.4 1.4 10 13 22 23 26 MLG0402Q1N6BT000
1.5 1.5 1.4 1.4 1.4 10 13 22 23 26 MLG0402Q1N6CT000
1.5 1.5 1.4 1.4 1.4 10 13 22 23 26 MLG0402Q1N6ST000
1.6 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402Q1N7BT000
1.6 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402Q1N7CT000
1.6 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402Q1N7ST000
1.7 1.6 1.6 1.6 1.6 11 14 22 24 27 MLG0402Q1N8BT000
1.7 1.6 1.6 1.6 1.6 11 14 22 24 27 MLG0402Q1N8CT000
1.7 1.6 1.6 1.6 1.6 11 14 22 24 27 MLG0402Q1N8ST000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(21/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
1.8 1.8 1.7 1.7 1.7 10 14 22 24 27 MLG0402Q1N9BT000
1.8 1.8 1.7 1.7 1.7 10 14 22 24 27 MLG0402Q1N9CT000
1.8 1.8 1.7 1.7 1.7 10 14 22 24 27 MLG0402Q1N9ST000
1.9 1.8 1.8 1.8 1.8 10 13 21 23 26 MLG0402Q2N0BT000
1.9 1.8 1.8 1.8 1.8 10 13 21 23 26 MLG0402Q2N0CT000
1.9 1.8 1.8 1.8 1.8 10 13 21 23 26 MLG0402Q2N0ST000
2.0 2.0 1.9 1.9 1.9 10 14 22 24 27 MLG0402Q2N1BT000
2.0 2.0 1.9 1.9 1.9 10 14 22 24 27 MLG0402Q2N1CT000
2.0 2.0 1.9 1.9 1.9 10 14 22 24 27 MLG0402Q2N1ST000
2.1 2.1 2.0 2.0 2.0 10 14 22 24 27 MLG0402Q2N2BT000
2.1 2.1 2.0 2.0 2.0 10 14 22 24 27 MLG0402Q2N2CT000
2.1 2.1 2.0 2.0 2.0 10 14 22 24 27 MLG0402Q2N2ST000
2.2 2.2 2.1 2.1 2.2 10 13 21 23 25 MLG0402Q2N3BT000
2.2 2.2 2.1 2.1 2.2 10 13 21 23 25 MLG0402Q2N3CT000
2.2 2.2 2.1 2.1 2.2 10 13 21 23 25 MLG0402Q2N3ST000
2.3 2.3 2.2 2.2 2.2 913 21 22 25 MLG0402Q2N4BT000
2.3 2.3 2.2 2.2 2.2 9 13 21 22 25 MLG0402Q2N4CT000
2.3 2.3 2.2 2.2 2.2 913 21 22 25 MLG0402Q2N4ST000
2.4 2.4 2.3 2.3 2.4 10 13 21 22 25 MLG0402Q2N5BT000
2.4 2.4 2.3 2.3 2.4 10 13 21 22 25 MLG0402Q2N5CT000
2.4 2.4 2.3 2.3 2.4 10 13 21 22 25 MLG0402Q2N5ST000
2.5 2.5 2.4 2.4 2.4 10 13 20 22 24 MLG0402Q2N6BT000
2.5 2.5 2.4 2.4 2.4 10 13 20 22 24 MLG0402Q2N6CT000
2.5 2.5 2.4 2.4 2.4 10 13 20 22 24 MLG0402Q2N6ST000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402Q2N7BT000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402Q2N7CT000
2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402Q2N7ST000
2.6 2.6 2.6 2.6 2.6 10 13 20 22 24 MLG0402Q2N8BT000
2.6 2.6 2.6 2.6 2.6 10 13 20 22 24 MLG0402Q2N8CT000
2.6 2.6 2.6 2.6 2.6 10 13 20 22 24 MLG0402Q2N8ST000
2.7 2.7 2.7 2.7 2.7 10 13 20 21 23 MLG0402Q2N9BT000
2.7 2.7 2.7 2.7 2.7 10 13 20 21 23 MLG0402Q2N9CT000
2.7 2.7 2.7 2.7 2.7 10 13 20 21 23 MLG0402Q2N9ST000
2.8 2.8 2.7 2.7 2.8 10 13 20 21 23 MLG0402Q3N0BT000
2.8 2.8 2.7 2.7 2.8 10 13 20 21 23 MLG0402Q3N0CT000
2.8 2.8 2.7 2.7 2.8 10 13 20 21 23 MLG0402Q3N0ST000
2.9 2.9 2.9 2.9 2.9 9 12 19 21 23 MLG0402Q3N1BT000
2.9 2.9 2.9 2.9 2.9 912 19 21 23 MLG0402Q3N1CT000
2.9 2.9 2.9 2.9 2.9 9 12 19 21 23 MLG0402Q3N1ST000
3.0 3.0 3.0 3.0 3.0 912 19 20 22 MLG0402Q3N2BT000
3.0 3.0 3.0 3.0 3.0 9 12 19 20 22 MLG0402Q3N2CT000
3.0 3.0 3.0 3.0 3.0 912 19 20 22 MLG0402Q3N2ST000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(22/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
3.2 3.1 3.1 3.1 3.1 9 12 19 21 23 MLG0402Q3N3BT000
3.2 3.1 3.1 3.1 3.1 912 19 21 23 MLG0402Q3N3CT000
3.2 3.1 3.1 3.1 3.1 9 12 19 21 23 MLG0402Q3N3ST000
3.2 3.2 3.2 3.2 3.2 912 19 20 22 MLG0402Q3N4BT000
3.2 3.2 3.2 3.2 3.2 9 12 19 20 22 MLG0402Q3N4CT000
3.2 3.2 3.2 3.2 3.2 912 19 20 22 MLG0402Q3N4ST000
3.3 3.3 3.3 3.3 3.3 9 12 19 20 22 MLG0402Q3N5BT000
3.3 3.3 3.3 3.3 3.3 912 19 20 22 MLG0402Q3N5CT000
3.3 3.3 3.3 3.3 3.3 9 12 19 20 22 MLG0402Q3N5ST000
3.4 3.4 3.4 3.4 3.4 10 13 20 22 24 MLG0402Q3N6BT000
3.4 3.4 3.4 3.4 3.4 10 13 20 22 24 MLG0402Q3N6CT000
3.4 3.4 3.4 3.4 3.4 10 13 20 22 24 MLG0402Q3N6ST000
3.5 3.5 3.4 3.5 3.5 9 12 19 21 23 MLG0402Q3N7BT000
3.5 3.5 3.4 3.5 3.5 912 19 21 23 MLG0402Q3N7CT000
3.5 3.5 3.4 3.5 3.5 9 12 19 21 23 MLG0402Q3N7ST000
3.6 3.6 3.5 3.6 3.6 10 13 19 21 23 MLG0402Q3N8BT000
3.6 3.6 3.5 3.6 3.6 10 13 19 21 23 MLG0402Q3N8CT000
3.6 3.6 3.5 3.6 3.6 10 13 19 21 23 MLG0402Q3N8ST000
3.7 3.7 3.7 3.7 3.7 9 12 19 20 22 MLG0402Q3N9BT000
3.7 3.7 3.7 3.7 3.7 912 19 20 22 MLG0402Q3N9CT000
3.7 3.7 3.7 3.7 3.7 9 12 19 20 22 MLG0402Q3N9ST000
3.8 3.8 3.7 3.8 3.8 912 19 20 22 MLG0402Q4N0BT000
3.8 3.8 3.7 3.8 3.8 9 12 19 20 22 MLG0402Q4N0CT000
3.8 3.8 3.7 3.8 3.8 912 19 20 22 MLG0402Q4N0ST000
4.1 4.0 4.0 4.0 4.1 10 13 21 23 25 MLG0402Q4N3ST000
4.1 4.0 4.0 4.0 4.1 10 13 21 23 25 MLG0402Q4N3HT000
4.5 4.5 4.5 4.5 4.6 10 13 21 23 25 MLG0402Q4N7ST000
4.5 4.5 4.5 4.5 4.6 10 13 21 23 25 MLG0402Q4N7HT000
4.8 4.8 4.8 4.8 4.9 10 13 20 22 24 MLG0402Q5N1ST000
4.8 4.8 4.8 4.8 4.9 10 13 20 22 24 MLG0402Q5N1HT000
5.3 5.3 5.3 5.3 5.4 11 14 22 23 25 MLG0402Q5N6ST000
5.3 5.3 5.3 5.3 5.4 11 14 22 23 25 MLG0402Q5N6HT000
5.9 5.8 5.9 5.9 6.0 11 14 21 23 25 MLG0402Q6N2ST000
5.9 5.8 5.9 5.9 6.0 11 14 21 23 25 MLG0402Q6N2HT000
6.5 6.4 6.5 6.6 6.7 10 13 21 22 23 MLG0402Q6N8HT000
6.5 6.4 6.5 6.6 6.7 10 13 21 22 23 MLG0402Q6N8JT000
7.1 7.0 7.1 7.2 7.4 11 14 22 23 25 MLG0402Q7N5HT000
7.1 7.0 7.1 7.2 7.4 11 14 22 23 25 MLG0402Q7N5JT000
7.8 7.8 7.9 8.0 8.3 11 14 21 23 24 MLG0402Q8N2HT000
7.8 7.8 7.9 8.0 8.3 11 14 21 23 24 MLG0402Q8N2JT000
8.6 8.5 8.7 8.8 9.1 11 14 21 23 24 MLG0402Q9N1HT000
8.6 8.5 8.7 8.8 9.1 11 14 21 23 24 MLG0402Q9N1JT000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(23/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
* Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.*
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
9.5 9.5 9.8 9.9 10.3 11 14 21 22 23 MLG0402Q10NHT000
9.5 9.5 9.8 9.9 10.3 11 14 21 22 23 MLG0402Q10NJT000
11.4 11.4 11.9 12.2 12.8 11 13 20 21 21 MLG0402Q12NHT000
11.4 11.4 11.9 12.2 12.8 11 13 20 21 21 MLG0402Q12NJT000
14.1 14.0 14.8 15.2 16.2 11 14 20 21 21 MLG0402Q15NHT000
14.1 14.0 14.8 15.2 16.2 11 14 20 21 21 MLG0402Q15NJT000
17.0 17.2 21.3 23.3 29.2 11 13 16 16 13 MLG0402Q18NHT000
17.0 17.2 21.3 23.3 29.2 11 13 16 16 13 MLG0402Q18NJT000
20.7 21.1 28.1 32.0 45.2 10 12 13 12 9 MLG0402Q22NHT000
20.7 21.1 28.1 32.0 45.2 10 12 13 12 9MLG0402Q22NJT000
25.3 25.7 34.1 38.9 10 12 12 11 MLG0402Q27NHT000
25.3 25.7 34.1 38.9 10 12 12 11 MLG0402Q27NJT000
31.0 32.2 52.2 10 12 10 MLG0402Q33NHT000
31.0 32.2 52.2 10 12 10 MLG0402Q33NJT000
Product No. Manufacturer
4291B+16196D Agilent Technologies
(24/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
33N
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A+16196D Agilent Technologies
(25/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Qseries MLG0402Q Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
Q
10 100 1000 10000
Frequency(MHz)
33N 27N
22N
18N
15N
12N
6N8
5N6
3N9
3N3
2N7
2N2
1N8
1N5
1N0
1N2
4N7
8N2
10N
Product No. Manufacturer
E4991A+16196D Agilent Technologies
(26/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries
MLG0603P Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.15±0.050.15±0.05
0.60±0.03
0.09±0.04 0.09±0.04
0.30±0.030.30±0.03
Dimensions in mm
0.3
0.3 0.250.25
(27/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 Please contact us for information on inductance tolerance, G (±2%).
・Short bar residual inductance =0.43nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
0.6 ±0.1nH — 500 10.0 20.0 0.06 0.01 1000 MLG0603P0N6BT000
0.6 ±0.2nH —500 10.0 20.0 0.06 0.01 1000 MLG0603P0N6CT000
0.7 ±0.1nH — 500 10.0 20.0 0.06 0.01 1000 MLG0603P0N7BT000
0.7 ±0.2nH —500 10.0 20.0 0.06 0.01 1000 MLG0603P0N7CT000
0.8 ±0.1nH — 500 10.0 20.0 0.06 0.02 1000 MLG0603P0N8BT000
0.8 ±0.2nH —500 10.0 20.0 0.06 0.02 1000 MLG0603P0N8CT000
0.9 ±0.1nH — 500 10.0 20.0 0.06 0.02 1000 MLG0603P0N9BT000
0.9 ±0.2nH —500 10.0 20.0 0.06 0.02 1000 MLG0603P0N9CT000
1.0 ±0.3nH 14 500 10.0 20.0 0.07 0.02 1000 MLG0603P1N0ST000
1.0 ±0.1nH 14 500 10.0 20.0 0.07 0.02 1000 MLG0603P1N0BT000
1.0 ±0.2nH 14 500 10.0 20.0 0.07 0.02 1000 MLG0603P1N0CT000
1.1 ±0.3nH 14 500 10.0 19.9 0.07 0.03 1000 MLG0603P1N1ST000
1.1 ±0.1nH 14 500 10.0 19.9 0.07 0.03 1000 MLG0603P1N1BT000
1.1 ±0.2nH 14 500 10.0 19.9 0.07 0.03 1000 MLG0603P1N1CT000
1.2 ±0.3nH 14 500 10.0 16.0 0.08 0.04 800 MLG0603P1N2ST000
1.2 ±0.1nH 14 500 10.0 16.0 0.08 0.04 800 MLG0603P1N2BT000
1.2 ±0.2nH 14 500 10.0 16.0 0.08 0.04 800 MLG0603P1N2CT000
1.3 ±0.3nH 14 500 10.0 13.9 0.08 0.03 800 MLG0603P1N3ST000
1.3 ±0.1nH 14 500 10.0 13.9 0.08 0.03 800 MLG0603P1N3BT000
1.3 ±0.2nH 14 500 10.0 13.9 0.08 0.03 800 MLG0603P1N3CT000
1.4 ±0.3nH 14 500 10.0 11.7 0.09 0.04 800 MLG0603P1N4ST000
1.4 ±0.1nH 14 500 10.0 11.7 0.09 0.04 800 MLG0603P1N4BT000
1.4 ±0.2nH 14 500 10.0 11.7 0.09 0.04 800 MLG0603P1N4CT000
1.5 ±0.3nH 14 500 10.0 14.9 0.10 0.03 800 MLG0603P1N5ST000
1.5 ±0.1nH 14 500 10.0 14.9 0.10 0.03 800 MLG0603P1N5BT000
1.5 ±0.2nH 14 500 10.0 14.9 0.10 0.03 800 MLG0603P1N5CT000
1.6 ±0.3nH 14 500 10.0 13.4 0.10 0.03 700 MLG0603P1N6ST000
1.6 ±0.1nH 14 500 10.0 13.4 0.10 0.03 700 MLG0603P1N6BT000
1.6 ±0.2nH 14 500 10.0 13.4 0.10 0.03 700 MLG0603P1N6CT000
1.7 ±0.3nH 14 500 10.0 12.8 0.10 0.02 700 MLG0603P1N7ST000
1.7 ±0.1nH 14 500 10.0 12.8 0.10 0.02 700 MLG0603P1N7BT000
1.7 ±0.2nH 14 500 10.0 12.8 0.10 0.02 700 MLG0603P1N7CT000
1.8 ±0.3nH 14 500 9.0 10.7 0.10 0.03 700 MLG0603P1N8ST000
1.8 ±0.1nH 14 500 9.0 10.7 0.10 0.03 700 MLG0603P1N8BT000
1.8 ±0.2nH 14 500 9.0 10.7 0.10 0.03 700 MLG0603P1N8CT000
1.9 ±0.3nH 14 500 9.0 10.9 0.10 0.04 600 MLG0603P1N9ST000
1.9 ±0.1nH 14 500 9.0 10.9 0.10 0.04 600 MLG0603P1N9BT000
1.9 ±0.2nH 14 500 9.0 10.9 0.10 0.04 600 MLG0603P1N9CT000
2.0 ±0.3nH 14 500 8.5 10.1 0.10 0.03 600 MLG0603P2N0ST000
2.0 ±0.1nH 14 500 8.5 10.1 0.10 0.03 600 MLG0603P2N0BT000
2.0 ±0.2nH 14 500 8.5 10.1 0.10 0.03 600 MLG0603P2N0CT000
2.1 ±0.3nH 14 500 8.0 9.8 0.10 0.05 600 MLG0603P2N1ST000
2.1 ±0.1nH 14 500 8.0 9.8 0.10 0.05 600 MLG0603P2N1BT000
2.1 ±0.2nH 14 500 8.0 9.8 0.10 0.05 600 MLG0603P2N1CT000
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(28/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 Please contact us for information on inductance tolerance, G (±2%).
・Short bar residual inductance =0.43nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
2.2 ±0.3nH 14 500 7.5 9.0 0.10 0.07 600 MLG0603P2N2ST000
2.2 ±0.1nH 14 500 7.5 9.0 0.10 0.07 600 MLG0603P2N2BT000
2.2 ±0.2nH 14 500 7.5 9.0 0.10 0.07 600 MLG0603P2N2CT000
2.3 ±0.3nH 14 500 7.5 8.4 0.20 0.07 600 MLG0603P2N3ST000
2.3 ±0.1nH 14 500 7.5 8.4 0.20 0.07 600 MLG0603P2N3BT000
2.3 ±0.2nH 14 500 7.5 8.4 0.20 0.07 600 MLG0603P2N3CT000
2.4 ±0.3nH 14 500 7.5 10.9 0.20 0.12 500 MLG0603P2N4ST000
2.4 ±0.1nH 14 500 7.5 10.9 0.20 0.12 500 MLG0603P2N4BT000
2.4 ±0.2nH 14 500 7.5 10.9 0.20 0.12 500 MLG0603P2N4CT000
2.5 ±0.3nH 14 500 7.5 9.9 0.20 0.09 500 MLG0603P2N5ST000
2.5 ±0.1nH 14 500 7.5 9.9 0.20 0.09 500 MLG0603P2N5BT000
2.5 ±0.2nH 14 500 7.5 9.9 0.20 0.09 500 MLG0603P2N5CT000
2.6 ±0.3nH 14 500 7.5 10.1 0.20 0.14 500 MLG0603P2N6ST000
2.6 ±0.1nH 14 500 7.5 10.1 0.20 0.14 500 MLG0603P2N6BT000
2.6 ±0.2nH 14 500 7.5 10.1 0.20 0.14 500 MLG0603P2N6CT000
2.7 ±0.3nH 14 500 7.5 10.0 0.20 0.14 500 MLG0603P2N7ST000
2.7 ±0.1nH 14 500 7.5 10.0 0.20 0.14 500 MLG0603P2N7BT000
2.7 ±0.2nH 14 500 7.5 10.0 0.20 0.14 500 MLG0603P2N7CT000
2.8 ±0.3nH 14 500 7.5 9.9 0.20 0.10 500 MLG0603P2N8ST000
2.8 ±0.1nH 14 500 7.5 9.9 0.20 0.10 500 MLG0603P2N8BT000
2.8 ±0.2nH 14 500 7.5 9.9 0.20 0.10 500 MLG0603P2N8CT000
2.9 ±0.3nH 14 500 7.5 9.2 0.20 0.10 500 MLG0603P2N9ST000
2.9 ±0.1nH 14 500 7.5 9.2 0.20 0.10 500 MLG0603P2N9BT000
2.9 ±0.2nH 14 500 7.5 9.2 0.20 0.10 500 MLG0603P2N9CT000
3.0 ±0.3nH 14 500 7.5 9.1 0.20 0.14 450 MLG0603P3N0ST000
3.0 ±0.1nH 14 500 7.5 9.1 0.20 0.14 450 MLG0603P3N0BT000
3.0 ±0.2nH 14 500 7.5 9.1 0.20 0.14 450 MLG0603P3N0CT000
3.1 ±0.3nH 14 500 7.5 8.8 0.20 0.10 450 MLG0603P3N1ST000
3.1 ±0.1nH 14 500 7.5 8.8 0.20 0.10 450 MLG0603P3N1BT000
3.1 ±0.2nH 14 500 7.5 8.8 0.20 0.10 450 MLG0603P3N1CT000
3.2 ±0.3nH 14 500 7.5 8.4 0.20 0.14 450 MLG0603P3N2ST000
3.2 ±0.1nH 14 500 7.5 8.4 0.20 0.14 450 MLG0603P3N2BT000
3.2 ±0.2nH 14 500 7.5 8.4 0.20 0.14 450 MLG0603P3N2CT000
3.3 ±0.3nH 14 500 7.5 8.4 0.20 0.13 450 MLG0603P3N3ST000
3.3 ±0.1nH 14 500 7.5 8.4 0.20 0.13 450 MLG0603P3N3BT000
3.3 ±0.2nH 14 500 7.5 8.4 0.20 0.13 450 MLG0603P3N3CT000
3.4 ±0.3nH 14 500 7.0 8.1 0.20 0.13 450 MLG0603P3N4ST000
3.4 ±0.1nH 14 500 7.0 8.1 0.20 0.13 450 MLG0603P3N4BT000
3.4 ±0.2nH 14 500 7.0 8.1 0.20 0.13 450 MLG0603P3N4CT000
3.5 ±0.3nH 14 500 6.5 8.0 0.20 0.12 450 MLG0603P3N5ST000
3.5 ±0.1nH 14 500 6.5 8.0 0.20 0.12 450 MLG0603P3N5BT000
3.5 ±0.2nH 14 500 6.5 8.0 0.20 0.12 450 MLG0603P3N5CT000
3.6 ±0.3nH 14 500 6.5 7.7 0.20 0.10 400 MLG0603P3N6ST000
3.6 ±0.1nH 14 500 6.5 7.7 0.20 0.10 400 MLG0603P3N6BT000
3.6 ±0.2nH 14 500 6.5 7.7 0.20 0.10 400 MLG0603P3N6CT000
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(29/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 Please contact us for information on inductance tolerance, G (±2%).
・Short bar residual inductance =0.43nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
3.7 ±0.3nH 14 500 6.5 7.4 0.20 0.14 400 MLG0603P3N7ST000
3.7 ±0.1nH 14 500 6.5 7.4 0.20 0.14 400 MLG0603P3N7BT000
3.7 ±0.2nH 14 500 6.5 7.4 0.20 0.14 400 MLG0603P3N7CT000
3.8 ±0.3nH 14 500 5.8 7.0 0.30 0.24 400 MLG0603P3N8ST000
3.8 ±0.1nH 14 500 5.8 7.0 0.30 0.24 400 MLG0603P3N8BT000
3.8 ±0.2nH 14 500 5.8 7.0 0.30 0.24 400 MLG0603P3N8CT000
3.9 ±0.3nH 14 500 5.8 7.1 0.30 0.22 400 MLG0603P3N9ST000
3.9 ±0.1nH 14 500 5.8 7.1 0.30 0.22 400 MLG0603P3N9BT000
3.9 ±0.2nH 14 500 5.8 7.1 0.30 0.22 400 MLG0603P3N9CT000
4.0 ±0.3nH 14 500 5.8 6.7 0.40 0.21 350 MLG0603P4N0ST000
4.0 ±0.1nH 14 500 5.8 6.7 0.40 0.21 350 MLG0603P4N0BT000
4.0 ±0.2nH 14 500 5.8 6.7 0.40 0.21 350 MLG0603P4N0CT000
4.1 ±0.3nH 14 500 5.8 6.7 0.40 0.29 350 MLG0603P4N1ST000
4.1 ±0.1nH 14 500 5.8 6.7 0.40 0.29 350 MLG0603P4N1BT000
4.1 ±0.2nH 14 500 5.8 6.7 0.40 0.29 350 MLG0603P4N1CT000
4.2 ±0.3nH 14 500 5.8 6.6 0.40 0.24 350 MLG0603P4N2ST000
4.2 ±0.1nH 14 500 5.8 6.6 0.40 0.24 350 MLG0603P4N2BT000
4.2 ±0.2nH 14 500 5.8 6.6 0.40 0.24 350 MLG0603P4N2CT000
4.3 ±0.3nH 14 500 5.8 6.7 0.40 0.24 350 MLG0603P4N3ST000
4.3 ±3% 14 500 5.8 6.7 0.40 0.24 350 MLG0603P4N3HT000
4.3 ±5% 14 500 5.8 6.7 0.40 0.24 350 MLG0603P4N3JT000
4.7 ±0.3nH 14 500 5.5 6.9 0.40 0.16 350 MLG0603P4N7ST000
4.7 ±3% 14 500 5.5 6.9 0.40 0.16 350 MLG0603P4N7HT000
4.7 ±5% 14 500 5.5 6.9 0.40 0.16 350 MLG0603P4N7JT000
5.1 ±0.3nH 14 500 5.5 6.6 0.40 0.30 350 MLG0603P5N1ST000
5.1 ±3% 14 500 5.5 6.6 0.40 0.30 350 MLG0603P5N1HT000
5.1 ±5% 14 500 5.5 6.6 0.40 0.30 350 MLG0603P5N1JT000
5.6 ±0.3nH 14 500 4.0 5.3 0.40 0.32 350 MLG0603P5N6ST000
5.6 ±3% 14 500 4.0 5.3 0.40 0.32 350 MLG0603P5N6HT000
5.6 ±5% 14 500 4.0 5.3 0.40 0.32 350 MLG0603P5N6JT000
6.2 ±0.3nH 14 500 4.0 6.3 0.70 0.59 300 MLG0603P6N2ST000
6.2 ±3% 14 500 4.0 6.3 0.70 0.59 300 MLG0603P6N2HT000
6.2 ±5% 14 500 4.0 6.3 0.70 0.59 300 MLG0603P6N2JT000
6.8 ±3% 14 500 4.0 6.1 0.75 0.62 300 MLG0603P6N8HT000
6.8 ±5% 14 500 4.0 6.1 0.75 0.62 300 MLG0603P6N8JT000
7.5 ±3% 14 500 4.0 5.4 0.80 0.70 300 MLG0603P7N5HT000
7.5 ±5% 14 500 4.0 5.4 0.80 0.70 300 MLG0603P7N5JT000
8.2 ±3% 14 500 4.0 5.2 0.85 0.71 250 MLG0603P8N2HT000
8.2 ±5% 14 500 4.0 5.2 0.85 0.71 250 MLG0603P8N2JT000
9.1 ±3% 14 500 4.0 5.0 0.90 0.76 250 MLG0603P9N1HT000
9.1 ±5% 14 500 4.0 5.0 0.90 0.76 250 MLG0603P9N1JT000
10.0 ±3% 14 500 4.0 4.7 0.95 0.85 250 MLG0603P10NHT000
10.0 ±5% 14 500 4.0 4.7 0.95 0.85 250 MLG0603P10NJT000
11.0 ±3% 14 500 3.5 4.5 1.00 0.64 250 MLG0603P11NHT000
11.0 ±5% 14 500 3.5 4.5 1.00 0.64 250 MLG0603P11NJT000
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(30/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 Please contact us for information on inductance tolerance, G (±2%).
・Short bar residual inductance =0.43nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
12.0 ±3% 14 500 3.5 4.3 1.10 0.82 250 MLG0603P12NHT000
12.0 ±5% 14 500 3.5 4.3 1.10 0.82 250 MLG0603P12NJT000
13.0 ±3% 14 500 3.2 4.2 1.10 0.87 250 MLG0603P13NHT000
13.0 ±5% 14 500 3.2 4.2 1.10 0.87 250 MLG0603P13NJT000
15.0 ±3% 14 500 3.2 3.7 1.20 0.94 250 MLG0603P15NHT000
15.0 ±5% 14 500 3.2 3.7 1.20 0.94 250 MLG0603P15NJT000
16.0 ±3% 14 500 3.0 3.6 1.20 1.00 200 MLG0603P16NHT000
16.0 ±5% 14 500 3.0 3.6 1.20 1.00 200 MLG0603P16NJT000
18.0 ±3% 14 500 3.0 3.5 1.40 1.04 200 MLG0603P18NHT000
18.0 ±5% 14 500 3.0 3.5 1.40 1.04 200 MLG0603P18NJT000
20.0 ±3% 14 500 2.2 3.3 1.90 1.33 150 MLG0603P20NHT000
20.0 ±5% 14 500 2.2 3.3 1.90 1.33 150 MLG0603P20NJT000
22.0 ±3% 14 500 2.2 2.9 1.90 1.31 150 MLG0603P22NHT000
22.0 ±5% 14 500 2.2 2.9 1.90 1.31 150 MLG0603P22NJT000
24.0 ±3% 14 500 2.2 2.9 2.10 1.17 140 MLG0603P24NHT000
24.0 ±5% 14 500 2.2 2.9 2.10 1.17 140 MLG0603P24NJT000
27.0 ±3% 14 500 2.2 2.7 2.10 1.45 140 MLG0603P27NHT000
27.0 ±5% 14 500 2.2 2.7 2.10 1.45 140 MLG0603P27NJT000
30.0 ±3% 10 300 1.8 2.3 2.20 1.37 130 MLG0603P30NHT000
30.0 ±5% 10 300 1.8 2.3 2.20 1.37 130 MLG0603P30NJT000
33.0 ±3% 10 300 1.8 2.4 2.20 1.55 130 MLG0603P33NHT000
33.0 ±5% 10 300 1.8 2.4 2.20 1.55 130 MLG0603P33NJT000
36.0 ±3% 10 300 1.8 2.2 2.40 1.49 120 MLG0603P36NHT000
36.0 ±5% 10 300 1.8 2.2 2.40 1.49 120 MLG0603P36NJT000
39.0 ±3% 10 300 1.8 2.2 2.40 1.72 120 MLG0603P39NHT000
39.0 ±5% 10 300 1.8 2.2 2.40 1.72 120 MLG0603P39NJT000
43.0 ±3% 10 300 1.6 2.0 2.90 1.61 110 MLG0603P43NHT000
43.0 ±5% 10 300 1.6 2.0 2.90 1.61 110 MLG0603P43NJT000
47.0 ±3% 10 300 1.6 2.0 2.90 2.18 110 MLG0603P47NHT000
47.0 ±5% 10 300 1.6 2.0 2.90 2.18 110 MLG0603P47NJT000
51.0 ±3% 10 300 1.4 1.9 3.50 1.87 100 MLG0603P51NHT000
51.0 ±5% 10 300 1.4 1.9 3.50 1.87 100 MLG0603P51NJT000
56.0 ±3% 10 300 1.4 1.8 3.50 2.35 100 MLG0603P56NHT000
56.0 ±5% 10 300 1.4 1.8 3.50 2.35 100 MLG0603P56NJT000
62.0 ±3% 10 300 1.2 1.6 3.50 2.12 100 MLG0603P62NHT000
62.0 ±5% 10 300 1.2 1.6 3.50 2.12 100 MLG0603P62NJT000
68.0 ±3% 9 300 1.2 1.6 3.50 2.69 100 MLG0603P68NHT000
68.0 ±5% 9300 1.2 1.6 3.50 2.69 100 MLG0603P68NJT000
75.0 ±3% 9 300 1.0 1.5 4.00 2.59 80 MLG0603P75NHT000
75.0 ±5% 9300 1.0 1.5 4.00 2.59 80 MLG0603P75NJT000
82.0 ±3% 9 300 1.0 1.5 4.00 2.71 80 MLG0603P82NHT000
82.0 ±5% 9300 1.0 1.5 4.00 2.71 80 MLG0603P82NJT000
91.0 ±3% 9 300 0.9 1.3 4.50 2.92 80 MLG0603P91NHT000
91.0 ±5% 9300 0.9 1.3 4.50 2.92 80 MLG0603P91NJT000
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(31/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 Please contact us for information on inductance tolerance, G (±2%).
・Short bar residual inductance =0.43nH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
100.0 ±3% 9 300 0.9 1.3 4.50 3.20 80 MLG0603PR10HT000
100.0 ±5% 9300 0.9 1.3 4.50 3.20 80 MLG0603PR10JT000
110.0 ±3% 9 300 0.8 1.1 5.00 3.50 80 MLG0603PR11HT000
110.0 ±5% 9300 0.8 1.1 5.00 3.50 80 MLG0603PR11JT000
120.0 ±3% 9 300 0.8 1.0 5.00 3.79 80 MLG0603PR12HT000
120.0 ±5% 9300 0.8 1.0 5.00 3.79 80 MLG0603PR12JT000
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(32/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. MLG0603P0N6BT000
0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. MLG0603P0N6CT000
0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. MLG0603P0N7BT000
0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. MLG0603P0N7CT000
0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 MLG0603P0N8BT000
0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 MLG0603P0N8CT000
0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 MLG0603P0N9BT000
0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 MLG0603P0N9CT000
1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 MLG0603P1N0BT000
1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 MLG0603P1N0CT000
1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 MLG0603P1N0ST000
1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 MLG0603P1N1BT000
1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 MLG0603P1N1CT000
1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 MLG0603P1N1ST000
1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 MLG0603P1N2BT000
1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 MLG0603P1N2CT000
1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 MLG0603P1N2ST000
1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 MLG0603P1N3BT000
1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 MLG0603P1N3CT000
1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 MLG0603P1N3ST000
1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 MLG0603P1N4BT000
1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 MLG0603P1N4CT000
1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 MLG0603P1N4ST000
1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 MLG0603P1N5BT000
1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 MLG0603P1N5CT000
1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 MLG0603P1N5ST000
1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 MLG0603P1N6BT000
1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 MLG0603P1N6CT000
1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 MLG0603P1N6ST000
1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 MLG0603P1N7BT000
1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 MLG0603P1N7CT000
1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 MLG0603P1N7ST000
1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 MLG0603P1N8BT000
1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 MLG0603P1N8CT000
1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 MLG0603P1N8ST000
1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 MLG0603P1N9BT000
1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 MLG0603P1N9CT000
1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 MLG0603P1N9ST000
2.0 2 2.0 2.0 2.0 19 23 35 37 41 MLG0603P2N0BT000
2.0 22.0 2.0 2.0 19 23 35 37 41 MLG0603P2N0CT000
2.0 2 2.0 2.0 2.0 19 23 35 37 41 MLG0603P2N0ST000
2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 MLG0603P2N1BT000
2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 MLG0603P2N1CT000
2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 MLG0603P2N1ST000
2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 MLG0603P2N2BT000
2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 MLG0603P2N2CT000
2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 MLG0603P2N2ST000
2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 MLG0603P2N3BT000
2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 MLG0603P2N3CT000
2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 MLG0603P2N3ST000
Product No. Manufacturer
4291B+16197A Agilent Technologies
(33/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 MLG0603P2N4BT000
2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 MLG0603P2N4ST000
2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 MLG0603P2N5BT000
2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 MLG0603P2N5CT000
2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 MLG0603P2N5ST000
2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 MLG0603P2N6BT000
2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 MLG0603P2N6CT000
2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 MLG0603P2N6ST000
2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 MLG0603P2N7BT000
2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 MLG0603P2N7CT000
2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 MLG0603P2N7ST000
2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 MLG0603P2N8BT000
2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 MLG0603P2N8CT000
2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 MLG0603P2N8ST000
2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 MLG0603P2N9BT000
2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 MLG0603P2N9CT000
2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 MLG0603P2N9ST000
3.0 33.0 3.1 3.1 17 21 32 34 37 MLG0603P3N0BT000
3.0 3 3.0 3.1 3.1 17 21 32 34 37 MLG0603P3N0CT000
3.0 33.0 3.1 3.1 17 21 32 34 37 MLG0603P3N0ST000
3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 MLG0603P3N1BT000
3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 MLG0603P3N1CT000
3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 MLG0603P3N1ST000
3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 MLG0603P3N2BT000
3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 MLG0603P3N2CT000
3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 MLG0603P3N2ST000
3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 MLG0603P3N3BT000
3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 MLG0603P3N3CT000
3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 MLG0603P3N3ST000
3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 MLG0603P3N4BT000
3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 MLG0603P3N4CT000
3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 MLG0603P3N4ST000
3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 MLG0603P3N5BT000
3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 MLG0603P3N5CT000
3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 MLG0603P3N5ST000
3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 MLG0603P3N6BT000
3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 MLG0603P3N6CT000
3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 MLG0603P3N6ST000
3.7 3.7 3.8 3.9 4.0 18 23 34 35 37 MLG0603P3N7BT000
3.7 3.7 3.8 3.9 4.0 18.0 23 34 35 37 MLG0603P3N7CT000
3.7 3.7 3.8 3.9 4.0 18.0 23 34 35 37 MLG0603P3N7ST000
3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 MLG0603P3N8BT000
3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 MLG0603P3N8CT000
3.8 3.8 3.9 4.0 4.1 17.0 22 32 33 36 MLG0603P3N8ST000
3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 MLG0603P3N9BT000
3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 MLG0603P3N9CT000
3.9 3.9 4.0 4.1 4.2 17.0 22 32 34 36 MLG0603P3N9ST000
4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 MLG0603P4N0BT000
4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 MLG0603P4N0CT000
4.0 4.0 4.1 4.2 4.4 18.0 22 32 33 36 MLG0603P4N0ST000
Product No. Manufacturer
4291B+16197A Agilent Technologies
(34/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 MLG0603P4N1BT000
4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 MLG0603P4N1CT000
4.1 4.1 4.3 4.3 4.5 18.0 22 33 34 36 MLG0603P4N1ST000
4.2 4.2 4.4 4.5 4.6 18.0 22 32 33 35 MLG0603P4N2BT000
4.2 4.2 4.4 4.5 4.6 18.0 22 32 33 35 MLG0603P4N2CT000
4.2 4.2 4.4 4.5 4.6 18 22 32 33 35 MLG0603P4N2ST000
4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 MLG0603P4N3ST000
4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 MLG0603P4N3HT000
4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 MLG0603P4N3JT000
4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 MLG0603P4N7ST000
4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 MLG0603P4N7HT000
4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 MLG0603P4N7JT000
5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 MLG0603P5N1ST000
5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 MLG0603P5N1HT000
5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 MLG0603P5N1JT000
5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 MLG0603P5N6ST000
5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 MLG0603P5N6HT000
5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 MLG0603P5N6JT000
6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 MLG0603P6N2ST000
6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 MLG0603P6N2HT000
6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 MLG0603P6N2JT000
6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 MLG0603P6N8HT000
6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 MLG0603P6N8JT000
7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 MLG0603P7N5HT000
7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 MLG0603P7N5JT000
8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 MLG0603P8N2HT000
8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 MLG0603P8N2JT000
9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 MLG0603P9N1HT000
9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 MLG0603P9N1JT000
10 10 11 12 13 16 21 28 28 28 MLG0603P10NHT000
10 10 11 12 13 16 21 28 28 28 MLG0603P10NJT000
11 11 13 13 15 18 23 30 30 30 MLG0603P11NHT000
11 11 13 13 15 18 23 30 30 30 MLG0603P11NJT000
12 12 14 15 17 18 22 28 28 27 MLG0603P12NHT000
12 12 14 15 17 18 22 28 28 27 MLG0603P12NJT000
13 13 15 16 19 18 22 28 28 26 MLG0603P13NHT000
13 13 15 16 19 18 22 28 28 26 MLG0603P13NJT000
15 15 18 20 24 18 22 27 26 24 MLG0603P15NHT000
15 15 18 20 24 18 22 27 26 24 MLG0603P15NJT000
16 16 20 22 27 18 22 26 25 22 MLG0603P16NHT000
16 16 20 22 27 18 22 26 25 22 MLG0603P16NJT000
18 18 23 26 33 18 22 25 24 20 MLG0603P18NHT000
18 18 23 26 33 18 22 25 24 20 MLG0603P18NJT000
20 21 27 31 42 18 22 23 22 17 MLG0603P20NHT000
20 21 27 31 42 18 22 23 22 17 MLG0603P20NJT000
22 23 34 40 68 18 21 21 18 11 MLG0603P22NHT000
22 23 34 40 68 18 21 21 18 11 MLG0603P22NJT000
24 25 36 43 72 19 22 21 18 11 MLG0603P24NHT000
24 25 36 43 72 19 22 21 18 11 MLG0603P24NJT000
27 28 45 57 18 21 18 15 MLG0603P27NHT000
27 28 45 57 18 21 18 15 MLG0603P27NJT000
Product No. Manufacturer
4291B+16197A Agilent Technologies
(35/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
Please contact us for information on inductance tolerance, G (±2%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
30 32 59 18 21 15 MLG0603P30NHT000
30 32 59 18 21 15 MLG0603P30NJT000
33 36 68 15 17 11 MLG0603P33NHT000
33 36 68 15 17 11 MLG0603P33NJT000
37 39 16 17 MLG0603P36NHT000
37 39 16 17 MLG0603P36NJT000
40 43 15 17 MLG0603P39NHT000
40 43 15 17 MLG0603P39NJT000
44 48 15 16 MLG0603P43NHT000
44 48 15 16 MLG0603P43NJT000
48 53 15 16 MLG0603P47NHT000
48 53 15 16 MLG0603P47NJT000
53 59 15 16 MLG0603P51NHT000
53 59 15 16 MLG0603P51NJT000
58 66 15 15 MLG0603P56NHT000
58 66 15 15 MLG0603P56NJT000
65 76 15 15 MLG0603P62NHT000
65 76 15 15 MLG0603P62NJT000
71 82 15 15 MLG0603P68NHT000
71 82 15 15 MLG0603P68NJT000
79 97 14 13 MLG0603P75NHT000
79 97 14 13 MLG0603P75NJT000
87 109 14 13 MLG0603P82NHT000
87 109 14 13 MLG0603P82NJT000
99 132 13 12 MLG0603P91NHT000
99 132 13 12 MLG0603P91NJT000
110 152 14 12 MLG0603PR10HT000
110 152 14 12 MLG0603PR10JT000
126 211 13 9 MLG0603PR11HT000
126 211 13 9MLG0603PR11JT000
151 12 MLG0603PR12HT000
151 12 MLG0603PR12JT000
Product No. Manufacturer
4291B+16197A Agilent Technologies
(36/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
R12
R10
82N 68N
56N
47N39N
33N 27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(37/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries MLG0603P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
Q
10 100 1000 10000
Frequency(MHz)
R12 R10
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
1N8
1N2
1N0
39N
56N
47N
68N
82N
33N
1N5
2N2
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(38/38)
INDUCTORS
20140922 / inductor_commercial_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Q, MLG-Pseries
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
Typ e A B K
MLG0402P 0.46±0.04 0.26±0.04 0.4 max.
MLG0402Q 0.46±0.04 0.26±0.04 0.4 max.
MLG0603P 0.68±0.05 0.38±0.05 0.5 max.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TDK:
MLG0603P0N7BTD25 MLG0603P1N1CT000 MLG0603P1N0CTD25 MLG0603P0N7CTD25 MLG0603P1N0BTD25
MLG0603P1N0STD25 MLG0603P1N0CT000 MLG0603P0N6BTD25 MLG0603P0N9CTD25 MLG0603P0N8CTD25
MLG0603P1N1STD25 MLG0603P1N1CTD25 MLG0603P1N0BT000 MLG0603P1N1BTD25 MLG0603P0N6CTD25
MLG0603P0N6BT000 MLG0603P1N1BT000 MLG0603P0N7BT000 MLG0603P0N8BTD25 MLG0603P0N9BTD25
MLG0603P0N8BT000 MLG0603P0N9BT000 MLG0603P3N5BT000 MLG0603P1N2STD25 MLG0603P3N0BTD25
MLG0603P1N7CT000 MLG0402Q3N0CT000 MLG0603P5N1HTD25 MLG0603P16NJTD25 MLG0603P4N7JT000
MLG0402Q2N8BT000 MLG0603P47NHTD25 MLG0603P6N2JTD25 MLG0603P7N5JTD25 MLG0402Q3N7CT000
MLG0402Q2N2CT000 MLG0603P36NHTD25 MLG0603P1N5BTD25 MLG0603P3N2CTD25 MLG0402Q3N5CT000
MLG0603P4N0BT000 MLG0603P2N3BT000 MLG0603P1N3CT000 MLG0402Q0N7BT000 MLG0603P2N1BTD25
MLG0603P1N3BT000 MLG0603PR11JTD25 MLG0402Q1N3CT000 MLG0603P4N3JT000 MLG0402Q3N1CT000
MLG0402Q2N6CT000 MLG0603P91NHT000 MLG0603P1N4STD25 MLG0603P1N6BT000 MLG0402Q2N4CT000
MLG0402Q2N5BT000 MLG0603P1N6BTD25 MLG0603P1N8STD25 MLG0603P4N1STD25 MLG0603P5N6JT000
MLG0603P4N2CTD25 MLG0402Q0N2BT000 MLG0603P8N2HT000 MLG0603P3N8BT000 MLG0402Q5N1HT000
MLG0603P2N6CTD25 MLG0402Q3N2CT000 MLG0402Q0N8BT000 MLG0603P3N0BT000 MLG0402Q2N5CT000
MLG0402Q3N8CT000 MLG0402Q6N2HT000 MLG0402Q0N9BT000 MLG0603P3N7CT000 MLG0603P10NJTD25
MLG0603P3N1CT000 MLG0603P1N9BT000 MLG0603P6N2JT000 MLG0603P2N7BT000 MLG0603P1N6CT000
MLG0603P75NHTD25 MLG0603P5N6HT000 MLG0603P4N7STD25 MLG0402Q9N1HT000 MLG0402Q3N0BT000
MLG0603P2N0STD25 MLG0402Q1N9BT000 MLG0402Q3N3BT000 MLG0402Q15NHT000 MLG0603P3N4STD25
MLG0603P5N6JTD25 MLG0603P6N2STD25 MLG0402Q2N3CT000 MLG0603P51NHT000 MLG0603P30NJTD25
MLG0603P16NHTD25 MLG0603P1N5CTD25 MLG0603P4N1BTD25 MLG0603P3N7BT000 MLG0603P6N8HTD25