HMC329LM3 v01.0505 MIXERS - DBL-BAL - SMT 9 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Typical Applications Features The HMC329LM3 is ideal for: Passive: No DC Bias Required * Point-to-Point Radios Input IP3: +19 dBm * Point-to-Multi-Point Radios LO/RF Isolation: 35 dB * SATCOM Leadless SMT Package, 25 mm2 * RADAR General Description Functional Diagram The HMC329LM3 is a 26 - 40 GHz surface mount, passive, double-balanced MMIC mixer in a SMT leadless chip carrier package. The mixer can be used as a downconverter or upconverter. Excellent isolations are provided by on-chip baluns. The chip requires no external components and no DC bias. All data is with the non-hermetic, epoxy sealed LM3 package mounted in a 50 Ohm test fixture. Utilizing the HMC329LM3 eliminates the need for wirebonding, thereby providing a consistent connection interface for the customer. Electrical Specifi cations, TA = +25 C LO = +13 dBm, IF = 1 GHz LO = +13 dBm, IF = 1 GHz Parameter Units Min. Typ. Max. Min. Typ. Frequency Range, RF & LO 26 - 32 32 - 40 Frequency Range, IF DC - 8 DC - 8 Conversion Loss Noise Figure (SSB) 8 10 8 10 Max. GHz GHz 9 11 dB 9 11 dB LO to RF Isolation 30 37 27 32 dB LO to IF Isolation 29 35 24 30 dB RF to IF Isolation 23 28 21 26 dB IP3 (Input) 16 19 16 20 dBm IP2 (Input) 45 55 46 56 dBm 1 dB Compression (Input) 9 11 7 10 dBm * Unless otherwise noted, all measurements performed as downconverter, IF= 1 GHz. 9 - 178 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Isolation vs. Frequency @ LO +13 dBm 0 0 -4 -10 ISOLATION (dB) -8 -12 + 25 C + 85 C - 40 C -16 9 -30 -50 24 27 30 33 36 FREQUENCY (GHz) 39 42 Conversion Gain vs. LO Drive 24 26 28 30 32 34 36 FREQUENCY (GHz) 38 40 42 Upconverter Performance vs. LO Drive 0 0 + 9 dBm + 11 dBm + 13 dBm + 15 dBm -4 CONVERSION GAIN (dB) CONVERSION GAIN (dB) -20 -40 -20 -8 -12 -16 -20 -4 -8 -12 + 9 dBm + 11 dBm + 13 dBm + 15 dBm -16 -20 24 27 30 33 36 FREQUENCY (GHz) 39 42 24 30 33 36 39 42 39 42 LO and RF Return Loss @ LO = +13 dBm 0 -4 -4 RETURN LOSS (dB) 0 -8 -12 CONVERSION GAIN IF RETURN LOSS -16 27 FREQUENCY (GHz) IF Bandwidth and IF Return Loss @ LO = +13 dBm RESPONSE (dB) RF/IF LO/RF LO/IF MIXERS - DBL-BAL - SMT CONVERSION GAIN (dB) Conversion Gain vs. Temperature @ LO = +13 dBm RF RETURN LOSS LO RETURN LOSS -8 -12 -16 -20 -20 0 2 4 6 8 FREQUENCY (GHz) 10 12 24 27 30 33 36 FREQUENCY (GHz) For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 9 - 179 HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Input IP3 vs. Temperature @ LO = +13 dBm 25 25 20 20 IP3 (dBm) 9 IP3 (dBm) Input IP3 vs. LO Drive* 15 10 + 11 dBm + 13 dBm + 15 dBm + 25 C + 85 C - 40 C 10 5 0 0 26 28 30 32 34 36 38 40 26 28 30 FREQUENCY (GHz) 32 36 38 40 38 40 Input IP2 vs. Temperature @ LO = +13 dBm 70 65 65 60 60 IP2 (dBm) 70 55 50 55 50 + 11 dBm + 13 dBm + 15 dBm 45 + 25 C + 85 C - 40 C 45 40 40 26 28 30 32 34 36 38 40 26 28 FREQUENCY (GHz) 30 32 34 36 FREQUENCY (GHz) Input P1dB vs. Temperature @ LO = +13 dBm MxN Spurious Outputs as a Down Converter 15 nLO mRF 13 P1dB (dBm) 34 FREQUENCY (GHz) Input IP2 vs. LO Drive* IP2 (dBm) MIXERS - DBL-BAL - SMT 5 15 11 0 1 0 xx 7 1 19 2 3 9 28 30 32 34 4 0 41 57 67 74 69 71 74 74 RF = 31 GHz @ -10 dBm LO = 32 GHz @ +13 dBm All values in dBc below IF output power level. 5 26 3 69 4 + 25 C + 85 C - 40 C 7 2 36 38 40 FREQUENCY (GHz) * Two-tone input power = -5 dBm each tone, 1 MHz spacing. 9 - 180 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Absolute Maximum Ratings +13 dBm LO Drive +27 dBm IF DC Current 2 mA Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ESD Sensitivity (HBM) Class 1B 9 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing MIXERS - DBL-BAL - SMT RF / IF Input NOTES: 1. MATERIAL: PLASTIC 2. PLATING: GOLD OVER NICKEL 3. ALL DIMENSIONS IN INCHES (MILLIMETERS) 4. ALL TOLERANCES ARE 0.005 (0.13) 5. ALL GROUNDS MUST BE SOLDERED TO PCB RF GROUND 6. INDICATES PIN 1 * For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 9 - 181 HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Pin Descriptions MIXERS - DBL-BAL - SMT 9 9 - 182 Pin Number Function Description 1, 2, 3 N/C This pin may be connected to the PCB ground or left unconnected. 4 RF This pin is DC coupled and matched to 50 Ohm from 25 to 40 GHz. 5 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source or sink more than 2 mA of current or part non-function and possible part failure will result. 6 LO This pin is DC coupled and matched to 50 Ohm from 25 to 40 GHz. GND Package base must be soldered to PCB RF ground. Interface Schematic For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Evaluation PCB The grounded Co-Planar Wave Guide (CPWG) PCB input/output transitions allow use of Ground-Signal-Ground (GSG) probes for testing. Suggested probe pitch is 400 mm (16 mils). Alternatively, the board can be mounted in a metal housing with 2.4 mm coaxial connectors. MIXERS - DBL-BAL - SMT 9 Evaluation Circuit Board Layout Design Details Layout Technique Micro Strip to CPWG Material Rogers 4003 with 1/2 oz. Cu Dielectric Thickness 0.008" (0.20 mm) Microstrip Line Width 0.018" (0.46 mm) CPWG Line Width 0.016" (0.41 mm) CPWG Line to GND Gap 0.005" (0.13 mm) Ground Via Hole Diameter 0.008" (0.20 mm) LM3 package mounted to evaluation PCB For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 9 - 183 HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Suggested LM3 PCB Land Pattern MIXERS - DBL-BAL - SMT 9 9 - 184 NOTES: 1. DIMENSIONS ARE IN INCHES [MILLIMETERS] 2. PAD WIDTH SHOWN IS FOR SOLDERING ONLY. BEYOND SOLDERING AREA ALL CONDUCTORS THAT CARRY RF AND MICROWAVE SIGNALS SHOULD HAVE 50 OHM CHARACTERISTIC IMPEDANCE. For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC329LM3 v01.0505 GaAs MMIC DOUBLE-BALANCED SMT MIXER, 26 - 40 GHz Recommended SMT Attachment Technique Preparation & Handling of the LM3 Millimeterwave Package for Surface Mounting 200 0 175 150 9 125 100 75 50 25 Cleanliness: Observe proper handling procedures to ensure clean 0 1 2 3 4 5 6 7 TIME (min) devices and PCBs. LM3 devices should remain in their original packaging until component placement to ensure no contamination or damage to RF, DC & ground contact areas. 8 Static Sensitivity: Follow ESD precautions to protect against ESD strikes. General Handling: Handle the LM3 package on the top with a vacuum collet or along the edges with a sharp pair of bent tweezers. Avoiding damaging the RF, DC, & ground contacts on the package bottom. Do not apply excess pressure to the top of the lid. Solder Materials & Temperature Profile: Follow the information contained in the application note. Hand soldering is not recommended. Conductive epoxy attachment is not recommended. Solder Paste: Solder paste should be selected based on the user's experience and be compatible with the metallization systems used. See the LM3 data sheet Outline drawing for pin & ground contact metallization schemes. Solder Paste Application: Solder paste is generally applied to the PCB using either a stencil printer or dot placement. The volume of solder paste will be dependent on PCB and component layout and should be controlled to ensure consistent mechanical & electrical performance. Excess solder may create unwanted electrical parasitics at high frequencies. MIXERS - DBL-BAL - SMT Follow these precautions to avoid permanent damage: 225 TEMPERATURE ( C) The HMC LM3 package was designed to be compatible with high volume surface mount PCB assembly processes. The LM3 package requires a specific mounting pattern to allow proper mechanical attachment and to optimize electrical performance at millimeterwave frequencies. This PCB layout pattern can be found on each LM3 product data sheet. It can also be provided as an electronic drawing upon request from Hittite Sales & Application Engineering. Solder Reflow: The soldering process is usually accomplished in a reflow oven but may also use a vapor phase process. A solder reflow profile is suggested above. Prior to reflowing product, temperature profiles should be measured using the same mass as the actual assemblies. The thermocouple should be moved to various positions on the board to account for edge and corner effects and varying component masses. The final profile should be determined by mounting the thermocouple to the PCB at the location of the device. Follow solder paste and oven vendor's recommendations when developing a solder reflow profile. A standard profile will have a steady ramp up from room temperature to the pre-heat temperature to avoid damage due to thermal shock. Allow enough time between reaching pre-heat temperature and reflow for the solvent in the paste to evaporate and the flux to completely activate. Reflow must then occur prior to the flux being completely driven off. The duration of peak reflow temperature should not exceed 15 seconds. Packages have been qualified to withstand a peak temperature of 235C for 15 seconds. Verify that the profile will not expose device to temperatures in excess of 235C. Cleaning: A water-based flux wash may be used. For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 9 - 185