Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. www.fairchildsemi.com KA3842B/KA3843B/KA3844B/ KA3845B SMPS Controller Features Description * * * * The KA3842B/KA3843B/KA3844B/KA3845B are fixed frequency current-mode PWM controller. They are specially designed for Off - Line and DC-to-DC converter applications with minimum external components. These integrated circuits feature a trimmed oscillator for precise duty cycle control, a temperature compensated reference, high gain error amplifier, current sensing comparator and a high current totempole output for driving a power MOSFET. The KA3842B and KA3844B have UVLO thresholds of 16V (on) and 10V (off). The KA3843B and KA3845B are 8.5V (on) and 7.9V (off). The KA3842B and KA3843B can operate within 100% duty cycle. The KA3844B and KA3845B can operate with 50% duty cycle. Low Start up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency up to 500KHz 8-DIP 1 14-SOP 1 Internal Block Diagram Rev. 1.0.2 (c)2002 Fairchild Semiconductor Corporation KA3842B/KA3843B/KA3844B/KA3845B Absolute Maximum Ratings Parameter Symbol Value Unit Supply Voltage VCC 30 V Output Current IO 1 A V(ANA) -0.3 to 6.3 V ISINK (E.A) 10 mA Power Dissipation at TA25C (8DIP) PD(Note1,2) 1200 mW Power Dissipation at TA25C (14SOP) Analog Inputs (Pin 2.3) Error Amp Output Sink Current PD(Note1,2) 680 mW Storage Temperature Range TSTG -65 ~ +150 C Lead Temperature (Soldering, 10sec) TLEAD +300 C Note: 1. Board Thickness 1.6mm, Board Dimension 76.2mm x114.3mm, (Reference EIA / JSED51-3, 51-7) 2. Do not exceeed PD and SOA (Safe Operation Area) Power Dissipation Curve 1200 8DIP POWER DISSIPATION (mW) 1100 1000 900 800 14SOP 700 600 500 400 300 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 AMBIENT TEMPERATURE () Thermal Data Characteristic Thermal Resistance Junction-ambient Symbol 8-DIP 14-SOP Unit Rthj-amb(MAX) 100 180 C/W Pin Array 8DIP,8SOP 8-DIP COMP 1 8 VREF COMP 1 VFB 2 7 VCC N/C 3 6 RT/C T 4 5 CURRENT SENSE 2 14SOP 14 VREF 2 13 N/C OUTPUT VFB 3 12 VCC GND N/C 4 11 PWR VC CURRENT SENSE 5 10 OUTPUT N/C 6 9 GND RT/C T 7 8 PWR GND KA3842B/KA3843B/KA3844B/KA3845B Electrical Characteristics (VCC=15V, RT=10K, CT=3.3nF, TA= 0C to +70C, unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit TJ = 25C, IREF = 1mA 4.90 5.00 5.10 V REFERENCE SECTION Reference Output Voltage VREF Line Regulation VREF 12VVCC25V - 6 20 mV Load Regulation VREF 1mAIREF20mA - 6 25 mV TA = 25C - -100 -180 mA TJ = 25C 47 52 57 KHz Short Circuit Output Current ISC OSCILLATOR SECTION Oscillation Frequency Frequency Change with Voltage Oscillator Amplitude f f/VCC 12VVCC25V - 0.05 1 % VOSC - - 1.6 - VP-P IBIAS - - -0.1 -2 A ERROR AMPLIFIER SECTION Input Bias Current Input Voltage Open Loop Voltage Gain VI(E>A) GVO Vpin1 = 2.5V 2.42 2.50 2.58 V 2V VO 4V (Note3) 65 90 - dB Power Supply Rejection Ratio PSRR 12V VCC 25V (Note3) 60 70 - dB Output Sink Current ISINK Vpin2 = 2.7V, Vpin1 = 1.1V 2 7 - mA -0.6 -1.0 - mA Output Source Current ISOURCE Vpin2 = 2.3V, Vpin1 = 5V High Output Voltage VOH Vpin2 = 2.3V, RL = 15K to GND 5 6 - V Low Output Voltage VOL Vpin2 = 2.7V, RL = 15K to Pin 8 - 0.8 1.1 V GV (Note 1 & 2) 2.85 3 3.15 V/V Vpin1 = 5V(Note 1) 0.9 1 1.1 V - 70 - dB - -3 -10 A ISINK = 20mA - 0.08 0.4 V ISINK = 200mA - 1.4 2.2 V CURRENT SENSE SECTION Gain Maximum Input Signal Power Supply Rejection Ratio Input Bias Current VI(MAX) PSRR 12V VCC 25V (Note1,3) - IBIAS OUTPUT SECTION Low Output Voltage High Output Voltage VOL VOH ISOURCE = 20mA 13 13.5 - V ISOURCE = 200mA 12 13.0 - V Rise Time tR TJ = 25C, CL= 1nF (Note 3) - 45 150 ns Fall Time tF TJ = 25C, CL= 1nF (Note 3) - 35 150 ns KA3842B/KA3844B 14.5 16.0 17.5 V KA3843B/KA3845B 7.8 8.4 9.0 V KA3842B/KA3844B 8.5 10.0 11.5 V KA3843B/KA3845B 7.0 7.6 8.2 V UNDER-VOLTAGE LOCKOUT SECTION Start Threshold Min. Operating Voltage (After Turn On) VTH(ST) VOPR(MIN) 3 KA3842B/KA3843B/KA3844B/KA3845B Electrical Characteristics (Continued) (VCC=15V, RT=10K, CT=3.3nF, TA= 0C to +70C unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit PWM SECTION Max. Duty Cycle Min. Duty Cycle D(Max) KA3842B/KA3843B 95 97 100 % D(MAX) KA3844B/KA3845B 47 48 50 % D(MIN) - - - 0 % IST - - 0.45 1 mA - 14 17 mA 30 38 - V TOTAL STANDBY CURRENT Start-Up Current Operating Supply Current ICC(OPR) Zener Voltage VZ Vpin3=Vpin2=ON ICC = 25mA Adjust VCC above the start threshould before setting at 15V Note: 1. Parameter measured at trip point of latch 2. Gain defined as: V pin1 A = ----------------- ,0 Vpin3 0.8V V pin3 3. These parameters, although guaranteed, are not 100 tested in production. Figure 1. Open Loop Test Circuit High peak currents associated with capacitive loads necessitate careful grounding techniques Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5K potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3. 4 KA3842B/KA3843B/KA3844B/KA3845B Figure 2. Under Voltage Lockout During Under-Voltage Lock-Out, the output driver is biased to a high impedance state. Pin 6 should be shunted to ground with a bleeder resistor to prevent activating the power switch with output leakage current. Figure 3. Error Amp Configuration Figure 4. Current Sense Circuit Peak current (IS) is determined by the formula: 1.0V I S ( MAX ) = -----------RS A small RC filter may be required to suppress switch transients. 5 KA3842B/KA3843B/KA3844B/KA3845B Figure 5. Oscillator Waveforms and Maximum Duty Cycle Oscillator timing capacitor, CT, is charged by VREF through RT and discharged by an internal current source. During the discharge time, the internal clock signal blanks the output to the low state. Selection of RT and CT therefore determines both oscillator frequency and maximum duty cycle. Charge and discharge times are determined by the formulas: tc = 0.55 RT CT 0.0063R T - 2.7 t D = R T C T I n ---------------------------------------- 0.0063R T - 4 Frequency, then, is: f=(tc + td)-1 1.8 ForRT > 5K ,f = --------------RT CT Figure 6. Oscillator Dead Time & Frequency Figure 7. Timing Resistance vs Frequency (Deadtime vs CT RT > 5k) Figure 8. Shutdown Techniques 6 KA3842B/KA3843B/KA3844B/KA3845B Shutdown of the KA3842B can be accomplished by two methods; either raise pin 3 above 1V or pull pin 1 below a voltage two diode drops above ground. Either method causes the output of the PWM comparator to be high (refer to block diagram). The PWM latch is reset dominant so that the output will remain low until the next clock cycle after the shutdown condition at pins 1 and/or 3 is removed. In one example, an externally latched shutdown may be accomplished by adding an SOR which will be reset by cycling VCC below the lower UVLO threshold. At this point the reference turns off, allowing the SCR to reset. Figure 9. Slope Compensation A fraction of the oscillator ramp can be resistively summed with the current sense signal to provide slope compensation for converters requiring duty cycles over 50%. Note that capacitor, CT, forms a filter with R2 to suppress the leading edge switch spikes. TEMPERATURE (C) TEMPERATURE (C) Figure 10. Temperature Drift (Vref) Figure 11. Temperature Drift (Ist) TEMPERATURE (C) Figure 12. Temperature Drift (Icc) 7 KA3842B/KA3843B/KA3844B/KA3845B Mechanical Dimensions Package Dimensions in millimeters 1.524 0.10 #5 2.54 0.100 5.08 MAX 0.200 7.62 0.300 3.40 0.20 0.134 0.008 +0.10 0.25 -0.05 +0.004 0~15 8 0.010 -0.002 3.30 0.30 0.130 0.012 0.33 0.013 MIN 0.060 0.004 #4 0.018 0.004 #8 9.60 MAX 0.378 #1 9.20 0.20 0.362 0.008 ( 6.40 0.20 0.252 0.008 0.46 0.10 0.79 ) 0.031 8-DIP KA3842B/KA3843B/KA3844B/KA3845B Mechanical Dimensions (Continued) Package Dimensions in millimeters 14-SOP MIN #8 0.60 0.20 0.024 0.008 MAX0.10 MAX0.004 1.80 MAX 0.071 3.95 0.20 0.156 0.008 5.72 0.225 0~ 8 +0.10 0.20 -0.05 +0.004 0.008 -0.002 6.00 0.30 0.236 0.012 1.27 0.050 #7 +0.10 0.406 -0.05 +0.004 0.016 -0.002 #14 8.70 MAX 0.343 #1 8.56 0.20 0.337 0.008 ( 0.47 ) 0.019 1.55 0.10 0.061 0.004 0.05 0.002 9 KA3842B/KA3843B/KA3844B/KA3845B Ordering Information Product Number Package Operating Temperature KA3842B KA3843B KA3844B 8-DIP KA3845B 0 ~ + 70C KA3842BD KA3843BD KA3844BD 14-SOP KA3845BD DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 2/18/02 0.0m 001 Stock#DSxxxxxxxx 2002 Fairchild Semiconductor Corporation ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com