1/13June 2003
■LOW QUIESCENT CURRENT: 300µA
■DESIGNED FOR RS-485 INTERFACE
APPLICATIONS
■-7V TO 12V COMMON MODE INPUT
VOLTAGE RANGE
■DRIVER MAINTAINS HIGH IMPEDANCE IN
3-STATEORWITHTHEPOWEROFF
■70mV TYPICAL INPUT HYSTERESIS
■30ns PROPAGATION DELAYS, 5ns SKEW
■OPERATE FROM A SINGLE 5V SUPPLY
■CURRENT LIMITING AND THERMAL
SHUTDOWN FOR DRIVER OVERLOAD
PROTECTION
■ALLOWS UP TO 64 TRANSCEIVERS ON
THE BUS
DESCRIPTION
The ST485 is al low power transceiver for RS-485
and RS-422 communication. Each part contains
one driver and one receiver.
This transceiver draw 300µA (typ.) of supply
current when unloaded or fully loaded with
disabled drivers.
It operates from a single 5V supply.
Driver is short-circuit current limited and is
protected against excessive power dissipation by
thermal shutdown circuitry that placed the driver
outputs into a high-impedance state. .
The ST485 is designed for bi-directional data
communications on multipoint bus transmission
line (half-duplex applciations).
The ST485 is available in three temperature
range: commercial (0°C to 70°C), industrial (-40°C
to 850°C) and automotive (-55°C to 125°C)
ORDERING CODES
Type Temperature
Range Package Comments
ST485CN 0 to 70 °C DIP-8 50parts per tube / 40tube per box
ST485BN -40 to 85 °C DIP-8 50parts per tube / 40tube per box
ST485XN -55 to 125 °C DIP-8 50parts per tube / 40tube per box
ST485CD 0 to 70 °C SO-8 (Tube) 100parts per tube / 20tube per box
ST485BD -40 to 85 °C SO-8 (Tube) 100parts per tube / 20tube per box
ST485XD -55 to 125 °C SO-8 (Tube) 100parts per tube / 20tube per box
ST485CDR 0 to 70 °C SO-8 (Tape & Reel) 2500 parts per reel
ST485BDR -40 to 85 °C SO-8 (Tape & Reel) 2500 parts per reel
ST485XDR -55 to 125 °C SO-8 (Tape & Reel) 2500 parts per reel
ST485
LOW POWER
RS-485/RS-422 TRANSCEIVER
DIP SOP
ST485
2/13
PIN CONFIGURATION
PIN DESCRIPTION
TRUTH TABLE (DRIVER)
X= Don’t Care; Z=High Impedance
TRUTH TABLE (RECEIVER)
X= Don’t Care; Z=High Impedance
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is
not implied.
PlN N° SYMBOL NAME AND FUNCTION
1 RO Receiver Output
2RE
Receiver Output Enable
3 DE Driver Output Enable
4 DI Driver Input
5 GND Ground
6 A Non-inverting Receiver Input and Non-inverting Driver Output
7 B Inverting Receiver Input and Inverting Driver Output
8VCC Supply Voltage
INPUTS OUTPUTS
RE DE DI B A
XHHLH
XHLHL
XLXZZ
INPUTS OUTPUT
RE DE A-B RO
LL≥ +0.2V H
LL≤ -0.2V L
L L INPUTS OPEN H
HL X Z
Symbol Parameter Value Unit
VCC Supply Voltage 7V
V
I
Control Input Voltage (RE, DE) -0.5 to (VCC + 0.5) V
VDI Driver Input Voltage (DI) -0.5 to (VCC + 0.5) V
VDO Driver Output Voltage (A, B) ± 14 V
VRI Receiver Input Voltage (A, B) ± 14 V
VRO Receiver Output Voltage (RO) -0.5 to (VCC + 0.5) V
ST485
3/13
DC ELECTRICAL CHARACTERISTICS
(VCC =5V± 5%, TA=T
MIN to TMAX , unless otherwise specified. Typical values are referred to TA= 25°C)
(See Note 1)
Note 1: All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device ground
unless specified.
Note 2: Supply current specification is valid for loaded transmitters when VDE =0V
Note 3: Applies to peak current. See typical Operating Characteristics.
Symbol Parameter Test Conditions
Value
Unit-40 to 85 °C -55 to 125 °C
Min. Typ. Max. Min. Max.
VOD1 Differential Driver Output
(No Load) 55V
V
OD2 Differential Driver Output
(With Load) RL=27Ω (RS-485) (See Fig.1)
RL=50Ω (RS-422) (See Fig.1) 1.5 5
51.4 5
5V
V
∆VOD Change in Magnitude of
Driver Differential Output
Voltage for
Complementary Output
States
RL=27Ω or 50Ω (See Fig. 1) 0.2 0.2 V
VOC Driver Common-Mode
Output Voltage RL=27Ω or 50Ω (See Fig. 1) 3 3 V
∆VOC Change in Magnitude of
Driver Common-Mode
Output Voltage for
Complementary Output
States
RL=27Ω or 50Ω (See Fig. 1) 0.2 0.2 V
VIH Input High Voltage RE, DE, DI 2.0 2.0 V
VIL Input Low Voltage RE, DE, DI 0.8 0.8 V
IIN1 Input Current RE, DE, DI ± 2± 2µA
IIN2 Input Current (A, B) VCM = 0V or 5.25V VDE =0V
V
IN = 12V
VIN = -7V 1
-0.8 1
-0.8 mA
mA
VTH Receiver Differential
Threshold Voltage VCM = -7 to 12V -0.2 0.2 -0.2 0.2 V
∆VTH Receiver Input Hysteresis VCM =0V 70 mV
V
OH Receiver Output High
Voltage IO= -4mA VID = 200mV 3.5 3.4 V
VOL Receiver Output Low
Voltage IO=4mA V
ID = -200mV 0.4 0.55 V
IOZR 3-State (High Impedance)
Output Current at
Receiver
VO= 0.4 to 2.4V ± 1± 1µA
RIN Receiver Input
Resistance VCM = -7 to 12V 24 24 KΩ
ICC No Load Supply Current
(Note 2) VRE =0VorV
CC
VDE =V
CC
VDE =0V 400
300 900
500 900
500 µA
µA
IOSD1 Driver Short-Circuit
Current, VO=High VO= -7 to 12V (Note 3) 35 250 35 250 mA
IOSD2 Driver Short-Circuit
Current, VO=Low VO= -7 to 12V (Note 3) 35 250 35 250 mA
IOSR Receiver Short-Circuit
Current VO=0VtoV
CC 7 95795mA
ST485
4/13
DRIVER SWITCHING CHARACTERISTICS
(VCC =5V± 5%, TA=TMIN toTMAX , unless otherwise specified.Typical values are referred to TA=25°C)
(See Note 1)
Note 1: All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device ground
unless specified.
RECEIVER SWITCHING CHARACTERISTICS
(VCC =5V± 5%, TA=T
MIN to TMAX , unless otherwise specified. Typical values are referred to TA= 25°C)
(See Note 1)
Note 1: All currents into device pins are positive; all cuttents out of device pins are negative; all voltages are referenced to device ground
unless specified.
Symbol Parameter Test Conditions
Value
Unit-40 to 85 °C -55 to 125 °C
Min. Typ. Max. Min. Max.
tPLH
tPHL
Propagation Delay Input
to Output RDIFF =54ΩC
L1 =C
L2 = 100pF
(See Fig. 3 and 5) 10 30 60 70 ns
tSK Output Skew to Output RDIFF =54ΩC
L1 =C
L2 = 100pF
(See Fig. 3 and 5) 510 10ns
t
TLH
tTHL
Rise or Fall Time RDIFF =54ΩC
L1 =C
L2 =
100pF
(See Fig. 3 and 5)
31540345ns
t
PZH Output Enable Time CL= 100pF S2 = Closed
(See Fig. 4 and 6) 70 90 90 ns
tPZL Output Enable Time CL= 100pF S1 = Closed
(See Fig. 4 and 6) 70 90 90 ns
tPLZ Output Disable Time CL= 15pF S1 = Closed
(See Fig. 4 and 6) 70 90 90 ns
tPHZ Output Disable Time CL= 15pF S2 = Closed
(See Fig. 4 and 6) 70 90 90 ns
Symbol Parameter Test Conditions
Value
Unit-40 to 85 °C -55 to 125 °C
Min. Typ. Max. Min. Max.
tPLH
tPHL
Propagation Delay Input
to Output RDIFF =54ΩC
L1 =C
L2 =
100pF
(See Fig. 3 and 7)
20 130 210 230 ns
tSKD Differential Receiver
Skew RDIFF =54ΩC
L1 =C
L2 =
100pF
(See Fig. 3 and 7)
13 ns
tPZH Output Enable Time CRL = 15pF S1 = Closed
(See Fig. 2 and 8) 20 50 56 ns
tPZL Output Enable Time CRL = 15pF S2 = Closed
(See Fig. 2 and 8) 20 50 56 ns
tPLZ Output Disable Time CRL = 15pF S1 = Closed
(See Fig. 2 and 8) 20 50 56 ns
tPHZ Output Disable Time CRL = 15pF S2 = Closed
(See Fig. 2 and 8) 20 50 56 ns
fMAX Maximum Data Rate 2.5 2.5 Mbps
ST485
5/13
TEST CIRCUITS AND TYPICAL CHARACTERISTICS
Figure 1 : Driver DC Test Load
Figure 2 : Receiver Timing Test Load
Figure 3 : Drive/Receiver Timing Test Circuit
Figure 4 : Driver Timing Test Load
ST485
6/13
Figure 5 : Driver Propagation Delay
Figure 6 : Driver Enable and Disable Time
ST485
7/13
Figure 7 : Receiver Propagation Delay
Figure 8 : Receiver Enable and Disable Time
ST485
8/13
Figure 9 : Receiver Output Current vs Output
Low Voltage
Figure 10 : Receiver Output Current vs Output
High Voltage
Figure 11 : Driver Output Current vs Output Low
Voltage
Figure 12 : Driver Output Current vs Output High
Voltage
Figure 13 : Supply Current vs Temperature
Figure 14 : Receiver High Level Output Voltage
vs Temperature
ST485
9/13
Figure 15 : Receiver Low Level Output Voltage
vs Temperature Figure 16 : Differential Driver Output Voltage vs
Temperature
ST485
10/13
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 3.3 0.130
a1 0.7 0.028
B 1.39 1.65 0.055 0.065
B1 0.91 1.04 0.036 0.041
b 0.5 0.020
b1 0.38 0.5 0.015 0.020
D 9.8 0.386
E 8.8 0.346
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 7.1 0.280
I 4.8 0.189
L 3.3 0.130
Z 0.44 1.6 0.017 0.063
Plastic DIP-8 MECHANICAL DATA
P001F
ST485
11/13
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 1.35 1.75 0.053 0.069
A1 0.10 0.25 0.04 0.010
A2 1.10 1.65 0.043 0.065
B 0.33 0.51 0.013 0.020
C 0.19 0.25 0.007 0.010
D 4.80 5.00 0.189 0.197
E 3.80 4.00 0.150 0.157
e 1.27 0.050
H 5.80 6.20 0.228 0.244
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
k ˚ (max.)
ddd 0.1 0.04
SO-8 MECHANICAL DATA
0016023/C
8
ST485
12/13
DIM. mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362
T 22.4 0.882
Ao 8.1 8.5 0.319 0.335
Bo 5.5 5.9 0.216 0.232
Ko 2.1 2.3 0.082 0.090
Po 3.9 4.1 0.153 0.161
P 7.9 8.1 0.311 0.319
Tape & Reel SO-8 MECHANICAL DATA
ST485
13/13
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
conseq uences of u se of such inform ation nor for any in fring ement of p atents or o ther ri ghts of th ird p arties which may r esul t f rom
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
