ESD133-B1-W01005 Protection Devices TVS (Transient Voltage Suppressor) Bi-directional, 5.5 V, 0.2 pF, 01005, RoHS and Halogen Free compliant Feature list * * * * * * * ESD / transient protection according to: - IEC61000-4-2 (ESD): 20 kV (air / contact discharge) - IEC61000-4-4 (EFT): 2.5 kV / 50 A (5/50 ns) - IEC61000-4-5 (Surge): 3 A (8/20 s) Bi-directional working voltage up to: VRWM = 5.5 V Line capacitance: CL = 0.2 pF (typical) at f = 1 MHz Clamping voltage: VCL = 13 V (typical) at ITLP = 16 A with RDYN = 0.56 (typical) Very low reverse current: IR < 1 nA (typical) Small form factor SMD size 01005 and low profile (0.43 mm x 0.23 mm x 0.15 mm); for further package information please refer to apllication note AN392 [3] Bi-directional and symmetric I/V characteristics for optimized design / assembly Potential applications * USB 3.0 / 3.1, Firewire, DVI, HDMI, S-ATA, DisplayPort, Thunderbolt * Mobile HDMI link, MDDI, MIPI, SWP For further information please refer to application note AN525 [4] Product validation Qualified for industrial applications according to relevant tests of JEDEC47/20/22 Device information a ) Pin configuration Figure 1 Pin configuration and schematic diagram Table 1 Part information b ) Schematic diagram Type Package Configuration Marking code ESD133-B1-W01005 WLL-2-2 1 line, bi-directional T 1) 1 The device has no marking on the device top. The marking code is on pad side. Datasheet www.infineon.com Please read the Important Notice and Warnings at the end of this document Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Table of contents Table of contents Feature list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical characteristic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 4.1 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 WLL-2-2 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Datasheet 2 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Maximum ratings 1 Maximum ratings Note: TA = 25 C, unless otherwise specified Table 2 Maximum ratings Parameter Symbol Values Unit Reverse working voltage 1) VRWM 5.5 V ESD discharge 2) VESD (contact) 20 kV VESD (air) 20 Peak pulse power 3) PPK 21 W Peak pulse current 3) IPP 3 A Operating temperature range TOP -55 to 125 C Storage temperature Tstg -65 to 150 C Attention: Stresses above the maximum values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings. Exceeding only one of these values may cause irreversible damage to the component. 1 2 3 Device snaps back to a low holding voltage. Please refer to AN525 for latch-up prevention [4] VESD according to IEC61000-4-2 (R = 330 , C = 150 pF discharge network) Stress pulse: 8/20s current waveform according to IEC61000-4-5 Datasheet 3 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Electrical characteristics 2 Electrical characteristics Note: TA = 25 C, unless otherwise specified Device is electrically symmetrical IF I PP I TLP VF IF VR IR ... Forward voltage ... Forward current ... Reverse voltage ... Reverse current DI RDYN = DV DV DI Ih Vt1 VRWM IT VTLP IR VCL Vh VR VCL VTLP IR Vh IT R DYN V RWM Vt1 Vh VCL VTLP IR IPP I TLP Ih IT Ih R DYN = DV DI DI DV -IPP -I TLP IR V RWM Vt1 VF ... Dynamic resistance ... Reverse working voltage max . ... Trigger voltage ... Holding voltage ... Clamping voltage ... TLP voltage ... Reverse leakage current ... Peak pulse current ... TLP current ... Holding current ... Test current Thyristor_ Characteristic _ Curve_Bi-Directional.vsd Figure 2 Datasheet Definitions of electrical characteristics 4 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Electrical characteristics Table 3 DC characteristics Parameter Symbol Values Min. Typ. Unit Note or Test Condition Max. Breakdown voltage Vbr 6.5 8 10 V IR = 1 mA Holding voltage Vh - 1.9 - V IR = Ih Holding reverse current Ih - 25 - mA VR=Vh Reverse current IR - - 100 nA VR = 5.5 V Unit Note or Test Condition pF VR = 0 V, f = 1 MHz Table 4 AC characteristics Parameter Symbol Values Min. Line capacitance Table 5 CL Typ. - 0.2 - - 0.2 - Symbol Values Min. Clamping voltage 1) VCL Clamping voltage 2) Dynamic resistance 1) 2 VR = 0 V, f = 2.5 GHz ESD and Surge characteristics Parameter 1 Max. RDYN Typ. Unit Note or Test Condition V ITLP = 8 A, tp = 100 ns Max. - 8.5 - - 13 - ITLP = 16 A, tp = 100 ns - 3 - IPP = 1 A, tp = 8/20 s - 7 - IPP = 3 A, tp = 8/20 s - 0.56 tp = 100 ns Please refer to Application Note AN210 [1]. TLP parameters: Z0 = 50 , tp = 100ns, tr = 0.6 ns. Stress pulse: 8/20s current waveform according to IEC61000-4-5 Datasheet 5 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 3 Typical characteristic diagrams Note: TA = 25 C, unless otherwise specified 10-6 10-7 -8 IR [A] 10 10-9 10-10 -11 10 -12 10 Figure 3 -5 -4 -3 -2 -1 0 VR [V] 1 2 3 4 5 3 4 5 Reverse leakage current: IR = f(VR) 0.5 CL [pF] 0.4 0.3 0.2 0.1 0 -5 Figure 4 Datasheet -4 -3 -2 -1 0 VR [V] 1 2 Line capacitance: CL = f(VR), f = 1 MHz 6 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 120 Scope: 6 GHz, 20 GS/s 100 80 VCL [V] VCL-max-peak = 109 V 60 VCL-30ns-peak = 13 V 40 20 0 -20 -50 Figure 5 0 50 100 150 200 tp [ns] 250 300 350 400 450 Clamping voltage (ESD):VCL = f(t), 8 kV positive pulse according to IEC 61000-4-2 20 0 -20 VCL [V] VCL-max-peak = -112 V -40 VCL-30ns-peak = -13 V -60 -80 Scope: 6 GHz, 20 GS/s -100 -120 -50 Figure 6 Datasheet 0 50 100 150 200 tp [ns] 250 300 350 400 450 Clamping voltage (ESD):VCL = f(t), 8 kV negative pulse according to IEC 61000-4-2 7 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 160 Scope: 6 GHz, 20 GS/s 140 120 VCL [V] 100 VCL-max-peak = 139 V 80 VCL-30ns-peak = 21 V 60 40 20 0 -20 -50 Figure 7 0 50 100 150 200 tp [ns] 250 300 350 400 450 Clamping voltage (ESD):VCL = f(t), 15 kV positive pulse according to IEC 61000-4-2 20 0 -20 VCL [V] -40 VCL-max-peak = -140 V -60 VCL-30ns-peak = -21 V -80 -100 -120 Scope: 6 GHz, 20 GS/s -140 -160 -50 Figure 8 Datasheet 0 50 100 150 200 tp [ns] 250 300 350 400 450 Clamping voltage (ESD):VCL = f(t), 15 kV negative pulse according to IEC 61000-4-2 8 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 40 ESD133-B1-W01005 RDYN 20 30 15 20 10 10 5 0 0 -10 -5 -20 -10 Equivalent VIEC [kV] ITLP [A] RDYN = 0.56 RDYN = 0.56 -30 -15 -40 -20 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 VTLP [V] Figure 9 Datasheet Clamping voltage (TLP): ITLP = f(VTLP) [1] 9 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 3.5 3 2.5 2 1.5 1 IPP [A] 0.5 0 -0.5 -1 -1.5 -2 -2.5 -3 -3.5 -10 Figure 10 Datasheet -5 0 VCL [V] 5 10 Clamping voltage (Surge): IPP = f(VCL) according to IEC61000-4-5 [1] 10 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Typical characteristic diagrams 0 Insertion Loss |S21| [dB] 1 2 3 4 ESD133-B1-W01005 5 0.01 Figure 11 Datasheet 0.1 1 Frequency [GHz] 10 Insertion loss vs. frequency in a 50 system 11 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices Package information 4 Package information 4.1 WLL-2-2 package Note: All dimensions are in units mm Top view Bottom view 0.15 0.01 0.23 0.03 0.28 (0.15) 0.43 0.03 2 1 0.13 0.02 0.2 0.02 SG-WLL-2-2-PO V01 Figure 12 WLL-2-2 package outline Copper Solder mask 0.3 0.15 0.23 0.3 0.15 0.23 Stencil apertures SG-WLL-2-2-FP V01 Figure 13 WLL-2-2 footprint (recommendations for Printed Circuit Board Assembly see [2]) 8 0.5 0.2 2 0.2 0.28 SG-WLL-2-2-TP V01 Figure 14 WLL-2-2 packing Marking on pad-side Datasheet 1 1 Figure 15 Type code 12 12 Type code WLL-2-2 marking example (marking code see Device information ) 12 Revision 1.0 2018-01-12 ESD133-B1-W01005 Protection Devices References 5 References [1] Infineon AG - Application note AN210: Effective ESD protection design at system level using VF-TLP characterization methodology [2] Infineon AG - Recommendation for printed circuit board assembly of Infineon WLL packages http://www.infineon.com/Packageinformation_WLL [3] Infineon AG - Application note AN392: TVS Diodes in ChipScalePackage reduce size and save cost [4] Infineon AG - Application note AN525: Latch-up prediction for SCR TVS device Revision history Revision history: Revision 0.9, 2016-10-18 Page or Item Subjects (major changes since previous revision) Revision 1.0, 2018-01-12 all Electrical characteristics updated and missing diagrams added Minor editorial changes Datasheet 13 Revision 1.0 2018-01-12 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2018-01-12 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2018 Infineon Technologies AG All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference IFX-haz1500360312222 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie") . With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies' products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury