HLMA-SH05 2 mm x 5 mm Rectangular AlInGaP Lamps Data Sheet Description Features The HLMA-SH05 is an epoxy encapsulated lamp in rectangular package which are easily stacked in arrays or used for discrete front panel indicators. Contrast and light uniformity are enhanced by a special epoxy diffusion and tinting process. * Rectangular light emitting surface Technology Package Dimensions This 2x5 rectangular solid state lamp utilizes the newly developed Aluminum Indium Gallium Phosphide (AlInGaP) LED technology. This material has a very high luminous efficiency, capable of producing high light output over a wide range of drive currents. * Excellent for flush mounting on panels * Long life: solid state reliability * Excellent uniformity of light output 5.18 (0.204) 4.93 (0.194) 5.46 (0.215) 4.95 (0.195) CATHODE LEAD Device Selection Guide 26.40 (1.00) MIN. Package Description Viewing Angle 2q1/2 Dominant Wavelength Rectangular, 2mm x 5 mm, Tinted, Diffused 110 615 nm 1.27 (0.060) NOMINAL 8.00 (0.315) 7.37 (0.290) 2.41 (0.095) 2.03 (0.085) 2.23 (0.088) 1.98 (0.078) SIDE VIEW 0.46 (0.018) SQ. NOMINAL 2.54 (0.100) NOMINAL BOTTOM VIEW NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. AN EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS. 3. THERE IS A MAXIMUM 1 TAPER FROM BASE TO THE TOP OF LAMP. HLMA-SXD5 pkg dimen Absolute Maximum Ratings DC Forward Current[1] 50 mA Peak Forward Current[2] 200 mA Average Forward Current (at IPEAK = 200 mA, f 1 KHz)[2] 45 mA Transient Forward Current[3] (10 s Pulse) 500 mA Reverse Voltage (IR = 100 A) 5V LED Junction Temperature 110C Operating Temperature Range -40 to +100C Storage Temperature Range -40 to +100C Wave Soldering Temperature (1.59 mm [0.063 in] below Body) 250C for 3 seconds Solder Dipping Temperature (1.59 mm [0.063 in] below Body) 260C for 5 seconds Notes: 1. Derate linearly as shown in Figure 4. 2. Refer to Figure 5 to establish pulsed operating conditions. 3. The transient peak current is the maximum non-recurring peak current the device can withstand without damaging the LED die and wire bonds. 1.0 200 REDDISH ORANGE IF - FORWARD CURRENT - mA RELATIVE INTENSITY AMBER 0.5 0 550 594 600 621 630 650 100 50 20 10 5 2 1 0.5 700 0 0.5 WAVELENGTH - nm 1.0 1.5 2.0 2.5 3.0 3.5 VF - FORWARD VOLTAGE - V Figure 1. Relative intensity vs. wavelength. Figure 2. Forward current vs. forward voltage. HLMA-SXD5 fig 2 HLMA-SX05 fig 1 60 2.0 1.5 1.0 0.5 0 0 10 20 30 40 50 IF - DC FORWARD CURRENT - mA Figure 3. Relative luminous intensity vs. foward current. HLMA-SX05 fig 3 2 50 45 40 35 RqJA = 618 C/W 30 25 20 RqJA = 412 C/W 15 10 5 0 0 10 20 30 40 50 60 70 80 90 100 TA - AMBIENT TEMPERATURE - C Figure 4. Maximum forward current vs. ambient temperature. Derating based on T Max = 110C. HLMA-SX05 fig 4 IAVG - AVERAGE CURRENT - mA IF - FORWARD CURRENT - mA RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 2.5 f > 1 KHz 50 40 f > 300 Hz 30 f > 100 Hz 20 10 0 50 100 150 200 IPEAK - PEAK FORWARD CURRENT - mA Figure 5. Maximum average current vs. peak foward current. HLMA-SX05 fig 5 Optical Characteristics at TA = 25C Luminous Intensity IV (mcd) @ 20 mA Part Number HLMA- Min. Typ. Peak Wavelength lpeak (nm) Typ. SH05 8 20 621 Color, Dominant Wavelength ld[1] (nm) Typ. Viewing Angle 2q1/2 Degrees[2] Typ. Luminous Efficacy hv (lm/w) 615 110 263 Notes: 1. The dominant wavelength, ld, is derived from the CIE Chromaticity Diagram and represents the color of the device. 2. q1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. Electrical Characteristics at TA = 25C Part Number HLMASH05 Forward Voltage VF (Volts) @ IF = 20 mA Reverse Breakdown VR (Volts) @ IR = 100 A Typ. Capacitance C (pF) VF = 0, f = 1 MHz Typ. Thermal Resistance RqJ-PIN (C/W) Speed of Response ts (ns) Time Constant e-t/ts Typ. Min. Typ. Min. 1.9 2.4 5 20 40 260 13 1.0 NORMALIZED INTENSITY 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 10090 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 ANGULAR DISPLACEMENT - DEGREES Figure 6. HLMA-SXD5 fig 6 For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2008 Avago Technologies. All rights reserved. AV02-1553EN - September 25, 2008