LM5041B LM5041B Cascaded PWM Controller Literature Number: SNVS605 LM5041B Cascaded PWM Controller General Description Features The LM5041B PWM controller contains all of the features necessary to implement either current-fed or voltage-fed push-pull or bridge power converters. These "Cascaded" topologies are well suited for multiple output and higher power applications. The LM5041B includes these four control outputs: the buck stage controls (HD and LD) and the push-pull control outputs (PUSH and PULL). Push-pull outputs are driven at 50% nominal duty cycle at one half of the switching frequency of the buck stage and can be configured for either a guaranteed overlap time (for current-fed applications) or a guaranteed non-overlap time (for voltage-fed applications). Push-pull stage MOSFETs can be driven directly from the internal gate drivers while the buck stage requires an external driver such as the LM5102. The LM5041B includes a highvoltage start-up regulator that operates over a wide input range of 15V to 100V. The PWM controller is designed for high-speed capability including an oscillator frequency range up to 1 MHz and total propagation delays of less than 100 ns. Additional features include line Under-Voltage Lock-Out (UVLO), Soft-Start, an error amplifier, precision voltage reference, and thermal shutdown. The differences between LM5041, LM5041A and LM5041B are as follows: In the LM5041A and the LM5041B version, the hiccup mode over-current protection is not employed and the VCC bias regulator is not disabled by a low state at the SS pin. In the LM5041B version, both the high and low side buck stage gate drivers are forced to a low state when the controller is disabled. In the LM5041 and the LM5041B version, the buck stage controller is disabled by either a low state at the UVLO pin or a low state at the SS pin. Also in the LM5041B version, the REF pin 5V regulator is not disabled by a UVLO pin low state. Internal Start-up Bias Regulator Programmable Line Under-Voltage Lockout (UVLO) with Adjustable Hysteresis Current Mode Control Internal Error Amplifier with Reference Cycle-by-cycle Over-Current Protection Leading Edge Blanking Programmable Push-Pull Overlap or Dead Time Internal 1.5A Push-Pull Gate Drivers Programmable Soft-Start Programmable Oscillator with Sync Capability Precision Reference Thermal Shutdown Applications Telecommunication Power Converters Industrial Power Converters Multi-Output Power Converters Packages TSSOP-16 LLP-16 (5x5 mm) Thermally Enhanced Typical Application Circuit 30086401 Simplified Cascaded Push-Pull Power Converter (c) 2009 National Semiconductor Corporation 300864 www.national.com LM5041B Cascaded PWM Controller May 1, 2009 LM5041B Connection Diagram 30086402 16-Lead TSSOP, LLP Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5041BMTC TSSOP-16 MTC-16 92 Units per anti-static tube LM5041BMTCX TSSOP-16 MTC-16 2500 Units on Tape and Reel LM5041BSD LLP-16 SDA-16A Coming Soon LM5041BSDX LLP-16 SDA-16A Coming Soon Pin Descriptions Pin # Pin Name 1 VIN Source Input Voltage Input to start-up regulator. Input range 15V to 100V. 2 FB Feedback Signal Inverting input for the internal error amplifier. The non-inverting input is connected to a 0.75V reference. 3 COMP Output of the Internal Error Amplifier There is an internal 5 k resistor pull-up on this pin. The error amplifier provides an active sink. 4 REF Precision 5 volt reference output Maximum output current: 10 mA. Locally decouple with a 0.1 F capacitor. Reference stays low until the VCC UV are satisfied. 5 HD Main Buck PWM control output Buck switch PWM control output. The maximum duty cycle clamp for this output corresponds to an off time of typically 240 ns per cycle. The LM5101 or LM5102 Buck stage gate driver can be used to level shift and drive the Buck switch MOSFET. 6 LD Buck Sync Switch control output Sync Switch control output. Inversion of HD output during normal operation. The LM5101 or LM5102 lower drive can be used to drive the synchronous rectifier switch. 7 VCC Output of the internal high voltage start-up If an auxiliary winding raises the voltage on this pin above the regulation set-point, the regulator. Regulated to internal start-up regulator will shutdown, reducing the IC power dissipation. 9 volts. 8 PUSH Output of the push-pull Output of the push-pull gate driver. Output capability of 1.5A peak . drivers 9 PULL Output of the push-pull Output of the push-pull gate driver. Output capability of 1.5A peak. drivers 10 PGND Power ground Connect directly to analog ground. 11 AGND Analog ground Connect directly to power ground. www.national.com Pin Description Pin Application Information 2 Pin Name 12 CS Current sense input Current sense input to the PWM comparator (current mode control). There is a 50 ns leading edge blanking on this pin. If CS exceeds 0.5V, the PWM controller will go into cycle by cycle current limit. 13 SS Soft-Start control An external capacitor and an internal 10 A current source, set the soft-start ramp. Both HD and LD will be forced to a low state if the SS pin is below the shutdown threshold of 0.45V. 14 TIME 15 RT / SYNC Oscillator timing resistor pin and sync An external resistor sets the oscillator frequency. This pin will also accept an external oscillator. 16 UVLO Line Under-Voltage Shutdown An external divider from the power source sets the shutdown levels. Threshold of operation equals 2.5V. Hysteresis is set by a switched internal current source (20 A). Die substrate The exposed die attach pad of the LLP package should be connected to a PCB thermal pad at ground potential. For additional information on using National Semiconductor's No Pull Back LLP package, please refer to Application Note AN-1187: Leadless Leadframe Package (LLP). LLP DAP SUB Pin Description Pin Application Information An external resistor (RSET) sets the overlap time or dead time for the push-pull outputs. Push-Pull overlap and A resistor connected between TIME and GND produces overlap. A resistor connected dead time control between TIME and REF produces dead time. 3 www.national.com LM5041B Pin # LM5041B ESD Rating(Note 2) Lead temperature (Note 3) Wave Infrared Vapor Phase Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND VCC to GND All Other Inputs to GND Junction Temperature Storage Temperature Range 100V 16V -0.3 to 7V 150C Operating Ratings 2 kV 4 seconds at 260C 10 seconds at 240C 75 seconds at 219C (Note 1) VIN Junction Temperature 15 to 90V -40C to +125C -65C to +150C Electrical Characteristics Unless otherwise stated the following conditions apply: VIN = 48V, VCC = 10V, RT = 26.7 k, RSET = 20 k. (Note 4). Limits in standard type are for TJ = 25C only; limits in boldface type apply over the Operating Junction Temperature (TJ) range of -40C to +125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Symbol Parameter Conditions Min Typ Max Units Startup Regulator VCC Reg I-VIN VCC Regulation Open circuit 8.7 9 9.3 V VCC Current Limit (Note 4) 15 25 - mA Startup Regulator Leakage (external Vcc Supply) VIN = 100V - 145 500 A Shutdown Current (Iin) UVLO = 0V, VCC = open - 350 450 A VCC Under-Voltage Lock-Out Threshold VCC rising VCC Reg 400 mV VCC Reg 275 mV - V 1.7 2.1 2.6 V - 3 4 mA VCC Supply VCC Under-Voltage Lock-Out Hysteresis Supply Current (ICC) CL = 0 Error Amplifier GBW Gain Bandwidth - 3 - MHz DC Gain - 80 - dB 0.735 0.75 0.765 V 4 8 - mA 4.85 5 5.15 V Input Voltage VFB = COMP COMP Sink Capability VFB = 1.5V, COMP= 1V Reference Supply VREF Ref Voltage IREF = 0 mA Ref Voltage Regulation IREF = 0 to 10 mA Ref Current Limit - 25 50 mV 15 20 - mA - 40 - ns 0.45 0.5 0.55 V - 50 - ns 2 5 - mA Current Limit ILIM Delay to Output CS Step from 0 to 0.6V Time to Onset of OUT Transition (90%) CL = 0 Cycle by Cycle Threshold Voltage Leading Edge Blanking Time CS Sink Current (clocked) CS = 0.3V Soft-Start Soft-Start Current Source 7 10 13 A Soft-Start to COMP Offset 0.35 0.55 0.75 V Shutdown Threshold 0.25 0.5 0.75 V www.national.com 4 Parameter Conditions Min Typ Max Units Oscillator Frequency1 RT = 26.7 k 180 175 200 220 225 kHz Frequency2 RT = 7.87 k 515 600 685 kHz - 3 3.5 V Sync threshold PWM Comparator Delay to Output COMP = 2V, CS stepped 0 to 0.4V Time to onset of OUT transition low - 25 - ns Max Duty Cycle TS = Oscillator Period - (Ts-240ns) / Ts - % Min Duty Cycle COMP = 0V - - 0 % - 0.32 - COMP to PWM Comparator Gain COMP Open Circuit Voltage FB = 0V 4.1 4.8 5.5 V COMP Short Circuit Current FB = 0V, COMP = 0V 0.6 1 1.4 mA - 110 - mV Under-Voltage Shutdown 2.44 2.5 2.56 V Under-voltage Shutdown Hysteresis Current Source 16 20 24 A Slope Compensation Slope Comp Amplitude Delta increase at PWM Comparator to CS UVLO Shutdown Buck Stage Outputs - 5 (VREF) - V Output High Saturation IOUT = 10 mA, REF = VOUT - 0.5 1 V Output Low Saturation IOUT = -10 mA - 0.5 1 V Rise Time CL = 100 pF - 10 - ns Fall Time CL = 100 pF - 10 - ns Output High level Push-Pull Outputs Overlap Time RSET = 20 k Connected to GND, 50% to 50% Transitions 60 90 120 ns Dead Time RSET = 20k Connected to REF, 50% to 50% Transitions 65 95 125 ns Output High Saturation IOUT = 50 mA VCC - VOUT - 0.25 0.5 V Output Low Saturation IOUT = 100 mA - 0.5 1 V Rise Time CL = 1 nF - 20 Fall Time CL = 1 nF - 20 - ns Thermal Shutdown Temp. - 165 - C Thermal Shutdown Hysteresis - 25 - C TSSOP Package - 125 - C/W LLP Package - 32 - C/W ns Thermal Shutdown TSD Thermal Resistance JA Thermal Resistance Junction to Ambient Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and conditions, see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Test Method is per JESD-22-A114. Note 3: For detailed information on soldering plastic TSSOP and LLP packages, please refer to Application Note AN-1520: A Guide to Board Layout for Best Thermal Resistance for Exposed Packages , Application Note AN-1187: Leadless Leadframe Package (LLP) , or go to www.national.com/packaging for more information. Note 4: Device thermal limitations may limit usable range. 5 www.national.com LM5041B Symbol LM5041B Typical Performance Characteristics VCC and VIN vs VIN VCC vs ICC 30086409 30086408 SS Pin Current vs Temp Frequency vs RT 30086410 30086415 Dead Time vs RSET Overlap Time vs RSET 30086412 30086411 www.national.com 6 LM5041B Overlap Time vs Temp Dead Time vs Temp 30086413 30086414 Error Amplifier Gain Phase 30086416 7 www.national.com LM5041B Block Diagram Simplified Block Diagram 30086403 www.national.com 8 Line Under-Voltage Detector The LM5041B PWM controller contains all of the features necessary to implement either current-fed or voltage-fed push-pull or bridge power converters. These "Cascaded" topologies are well suited for multiple output and higher power applications. The LM5041B includes these four control outputs: the buck stage controls (HD and LD) and the push-pull control outputs (PUSH and PULL). Push-pull outputs are driven at 50% nominal duty cycle at one half of the switching frequency of the buck stage and can be configured for either a guaranteed overlap time (for current-fed applications) or a guaranteed non-overlap time (for voltage-fed applications). Push-pull stage MOSFETs can be driven directly from the internal gate drivers while the buck stage requires an external driver such as the LM5102. The LM5041B includes a highvoltage start-up regulator that operates over a wide input range of 15V to 100V. The PWM controller is designed for high-speed capability including an oscillator frequency range up to 1 MHz and total propagation delays of less than 100 ns. Additional features include line Under-Voltage Lock-Out (UVLO), Soft-Start, an error amplifier, precision voltage reference, and thermal shutdown. The LM5041B contains a line Under-Voltage Lock-Out (UVLO) circuit. An external set-point resistor divider from VIN to ground sets the operational range of the converter. The divider must be designed such that the voltage at the UVLO pin will be greater than 2.5V when VIN is in the desired operating range. If the Under-Voltage threshold is not met, both HD and LD will be forced to low state and VCC regulator will be disabled while the push-pull outputs continue switching until the REF pin voltage falls below approximately 3V. ULVO hysteresis is accomplished with an internal 20 A current source that is switched on or off into the impedance of the set-point divider. When the UVLO threshold is exceeded, the current source is activated to instantly raise the voltage at the UVLO pin. When the UVLO pin falls below the 2.5V threshold, the current source is turned off causing the voltage at the UVLO pin to fall. The UVLO pin can also be used to implement a remote enable / disable function. By shorting the UVLO pin to ground, the converter can be disabled. Buck Stage Control Outputs The LM5041B Buck switch maximum duty cycle clamp ensures that there will be sufficient off time each cycle to recharge the bootstrap capacitor used in the high side gate driver. The Buck switch is guaranteed to be off, and the sync switch on, for at least 250 ns per switching cycle. The Buck stage control outputs (LD and HD) are CMOS buffers with logic levels of 0 to 5V. During any fault state or Under-Voltage off state, both HD and LD state will be forced to low by the buck stage control. High Voltage Start-Up Regulator The LM5041B contains an internal high-voltage start-up regulator, thus the input pin (Vin) can be connected directly to the line voltage. The regulator output is internally current limited to 15 mA. When power is applied, the regulator is enabled and sources current into an external capacitor connected to the Vcc pin. The recommended capacitance range for the Vcc regulator is 0.1F to 100 F. When the voltage on the Vcc pin reaches the regulation point of 9V, the internal voltage reference (REF) reaches its regulation point of 5V, and the softstart capacitor is charged above its shutdown threshold, the controller outputs are enabled. The Buck stage outputs will remain enabled until Vcc falls below 7V, the REF pin voltage falls below approximately 3V, the SS pin is forced below the 0.45V shutdown threshold or the line Under-Voltage Lock-Out detector indicates that Vin is out of range. The push-pull outputs continue switching until the REF pin voltage falls below approximately 3V. In typical applications, an auxiliary transformer winding is connected through a diode to the Vcc pin. This winding must raise the Vcc voltage above 9.3V to shut off the internal start-up regulator. Powering VCC from an auxiliary winding improves efficiency while reducing the controller's power dissipation. The recommended capacitance range for the Vref regulator output is 0.1F to 10 F. The external VCC capacitor must be sized such that the capacitor maintains a VCC voltage greater than 7V during the initial start-up. During a fault mode when the converter auxiliary winding is inactive, external current draw on the VCC line should be limited so the power dissipated in the start-up regulator does not exceed the maximum power dissipation of the controller. An external start-up or other bias rail can be used instead of the internal start-up regulator by connecting the VCC and the VIN pins together and feeding the external bias voltage into the two pins. Push-Pull Outputs The push pull outputs operate continuously at a nominal 50% duty cycle. A distinguishing feature of the LM5041B is the ability to accurately configure either dead time (both-off) or overlap time (both-on) on the complementary push-pull outputs. The overlap/dead time magnitude is controlled by a resistor connected to the TIME pin on the controller. The TIME pin holds one end of the resistor at 2.5V and the other end of the resistor should be connected to either REF for dead time control setting or to GND for overlap control. The polarity of the current in the TIME is detected by the LM5041B The magnitude of the overlap/dead time can be calculated as follows: Overlap Time (ns) = (3.66 x RSET) + 7 Overlap Time in ns, RSET connected to GND, RSET in k Dead Time (ns) = (3.69 x RSET) + 21 Dead Time in ns, RSET connected to REF, RSET in k Recommended RSET programming range: 10 k to 100 k Current-fed designs require a period of overlap to insure there is a continuous path for the buck inductor current. Voltage-fed designs require a period of dead time to insure there is no time when the push-pull transformer acts as a shorted turn to the low impedance sourcing node. The push-pull outputs alternate continuously under all conditions provided REF the voltage is greater than 3V. 9 www.national.com LM5041B Detailed Operating Description LM5041B 30086404 sense resistor. The capacitor associated with the CS filter must be placed close to the device and connected directly to the pins of the controller (CS and GND). If a current sense transformer is used, both leads of the transformer secondary should be routed to the sense resistor, which should also be located close to the IC. A resistor may be used for current sensing instead of a transformer, located in the push-pull transistor sources, but a low inductance type of resistor is required. When designing with a sense resistor, all of the noise sensitive low power grounds should be connected together around the IC and a single connection should be made to the high current power ground (sense resistor ground point). PWM Comparator The PWM comparator compares the slope compensated current ramp signal to the loop error voltage from the internal error amplifier (COMP pin). This comparator is optimized for speed in order to achieve minimum controllable duty cycles. The comparator polarity is such that 0V on the COMP pin will produce zero duty cycle in the buck stage. Error Amplifier An internal high gain wide-bandwidth error amplifier is provided within the LM5041B. The amplifier's non-inverting input is tied to a 0.75V reference. The inverting input is connected to the FB pin. In non-isolated applications the power converter output is connected to the FB pin via the voltage setting resistors. Loop compensation components are connected between the COMP and FB pins. For most isolated applications the error amplifier function is implemented on the secondary side of the converter and the internal error amp is not used. The internal error amplifier is configured as an open drain output and can be disabled by connecting the FB pin to ground. An internal 5 k pull-up resistor between the 5V reference and the COMP pin can be used as the pull-up for an opto-coupler in isolated applications. Oscillator and Sync Capability The LM5041B oscillator is set by a single external resistor connected between the RT pin and GND. To set a desired oscillator frequency (F), the necessary RT resistor can be calculated from: The buck stage will switch at the oscillator frequency and each push-pull output will switch at half the oscillator frequency in a push-pull configuration. The LM5041B can also be synchronized to an external clock. The external clock must have a higher frequency than the free running frequency set by the RT resistor. The clock signal should be capacitively coupled into the RT pin with a 100 pF capacitor. A peak voltage level greater than 3V is required for detection of the sync pulse. The sync pulse width should be set in the 15 ns to 150 ns range by the external components. The RT resistor is always required, whether the oscillator is free running or externally synchronized. The voltage at the RT pin is internally regulated to 2V. The RT resistor should be located very close to the device and connected directly to the pins of the IC (RT and GND). Current Limit/Current Sense The LM5041B provides cycle-by-cycle over-current protection. If the voltage at the CS comparator (CS pin voltage plus slope comp voltage) exceeds 0.5V the present buck stage duty cycle is terminated (cycle by cycle current limit). A small RC filter located near the controller is recommended to filter current sense signals at the CS pin. An internal MOSFET discharges the external CS pin for an additional 50 ns at the beginning of each cycle to reduce the leading edge spike that occurs when the buck stage MOSFET is turned on. The LM5041B current sense and PWM comparators are very fast, and may respond to short duration noise pulses. Layout considerations are critical for the current sense filter and www.national.com 10 Thermal Protection The PWM comparator compares the current sense signal to the voltage at the COMP pin. The output stage of the internal error amplifier generally drives the COMP pin. At duty cycles greater than 50%, current mode control circuits are subject to sub-harmonic oscillation. By adding an additional fixed ramp signal (slope compensation) to the current sense ramp, oscillations can be avoided. The LM5041B integrates this slope compensation by buffering the internal oscillator ramp and summing a current ramp generated by the oscillator internally with the current sense signal. Additional slope compensation may be provided by increasing the source impedance of the current sense signal. Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated, typically at 165 degrees Celsius, the controller is forced into a low-power standby state, disabling the output drivers and the bias regulator. This feature is provided to prevent catastrophic failures from accidental device overheating. Differences Between LM5041, LM5041A and LM5041B There are five differences between LM5041, LM5041A and LM5041B. In the LM5041A and the LM5041B versions, the hiccup mode over-current protection is not employed and the VCC bias regulator is not disabled by SS pin shutdown state. In the LM5041B version, both HD and LD will be low state when the PWM controller disabled. In the LM5041 and the LM5041B version, PWM controller is disabled by either a UVLO pin low state or SS pin shutdown state. Also in the LM5041B version, the REF pin output is not disabled by a UVLO pin low state. However, if VCC does not receive power from an external source, the UVLO pin low state will disable the internal VCC regulator and a VCC under-voltage condition will eventually disable REF as the VCC voltage falls. Soft-Start and Shutdown The soft-start feature allows the power converter to gradually reach the initial steady state operating point, thereby reducing start-up stresses and surges. At power on, a 10 A current is sourced out of the soft-start pin (SS) to charge an external capacitor. The capacitor voltage will ramp up slowly and will limit the maximum duty cycle of the buck stage. In the event of a fault as indicated by VCC Under-voltage, line Under-voltage the output drivers are disabled and the soft-start capacitor is discharged to 0.7V. When the fault condition is no longer present, a soft-start sequence will begin again and buck stage duty cycle will gradually increase as the soft-start capacitor is charged. The SS pin also serves as an enable input of HD and LD. Both HD and LD will be forced to a low state if the SS pin is below the shutdown threshold of 0.45V. Differences Between LM5041, LM5041A and LM5041B ITEM LM5041 LM5041A LM5041B Hiccup mode over-current protection Available N/A N/A No VCC disabled by SS shutdown Yes No REF disabled by UVLO pin low state Yes Yes No BUCK controller disabled by SS shutdown Yes No Yes BUCK driver states when the controller disabled HD : LOW LD :HIGH HD : LOW LD : HIGH HD : LOW LD : LOW Logic Table MODE CONTROLS UVLO SS DEVICE PIN STATES VCC REF HD LD PUSH&PULL 9V 5V PWM PWM 50% Duty Cycle GND GND LOW LM5041 Normal Operation HIGH UVLO Shutdown LOW SS Shutdown HIGH - LM5041A LM5041B LM5041 - LM5041A LM5041 LM5041A LM5041B LOW LOW LM5041B LOW HIGH GND GND 9V 5V 11 LOW HIGH LOW LOW 50% Duty Cycle www.national.com LM5041B Slope Compensation LM5041B Typical Application 30086406 FIGURE 1. Simplified Cascaded Half-Bridge www.national.com 12 LM5041B 30086407 Application Circuit: Input 35V to 80V, Output 2.5V, 50A 13 www.national.com LM5041B Physical Dimensions inches (millimeters) unless otherwise noted Molded TSSOP-16 NS Package Number MTC16 16-Lead LLP Surface Mount Package NS Package Number SDA16A www.national.com 14 LM5041B Notes 15 www.national.com LM5041B Cascaded PWM Controller Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise(R) Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University(R) www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated