LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
LM124-N/LM224-N/LM324-N/LM2902-N Low Power Quad Operational Amplifiers
Check for Samples: LM124-N,LM224-N,LM2902-N,LM324-N
1FEATURES ADVANTAGES
2• Internally Frequency Compensated for Unity • Eliminates Need for Dual Supplies
Gain • Four Internally Compensated Op Amps in a
• Large DC Voltage Gain 100 dB Single Package
• Wide Bandwidth (Unity Gain) 1 MHz • Allows Directly Sensing Near GND and VOUT
(Temperature Compensated) also Goes to GND
• Wide Power Supply Range: • Compatible with All Forms of Logic
– Single Supply 3V to 32V • Power Drain Suitable for Battery Operation
– or Dual Supplies ±1.5V to ±16V DESCRIPTION
• Very Low Supply Current Drain (700 The LM124-N series consists of four independent,
μA)—Essentially Independent of Supply high gain, internally frequency compensated
Voltage operational amplifiers which were designed
• Low Input Biasing Current 45 nA (Temperature specifically to operate from a single power supply
Compensated) over a wide range of voltages. Operation from split
power supplies is also possible and the low power
• Low Input Offset Voltage 2 mV supply current drain is independent of the magnitude
– and Offset Current: 5 nA of the power supply voltage.
• Input Common-Mode Voltage Range Includes Application areas include transducer amplifiers, DC
Ground gain blocks and all the conventional op amp circuits
• Differential Input Voltage Range Equal to the which now can be more easily implemented in single
Power Supply Voltage power supply systems. For example, the LM124-N
• Large Output Voltage Swing 0V to V+−1.5V series can be directly operated off of the standard
+5V power supply voltage which is used in digital
systems and will easily provide the required interface
UNIQUE CHARACTERISTICS electronics without requiring the additional ±15V
• In the Linear Mode the Input Common-Mode power supplies.
Voltage Range Includes Ground and the
Output Voltage can also Swing to Ground,
Even Though Operated from Only a Single
Power Supply Voltage
• The Unity Gain Cross Frequency is
Temperature Compensated
• The Input Bias Current is also Temperature
Compensated
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2004, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
Connection Diagrams
Note 1: LM124A available per JM38510/11006
Note 2: LM124-N available per JM38510/11005
Note 3: See STD Mil DWG 5962R99504 for Radiation Tolerant Device
Figure 1. Dual-In-Line Package - Top View
See Package Number J0014A D0014A or NFF0014A
Note 3: See STD Mil DWG 5962R99504 for Radiation Tolerant Device
Figure 2. See Package Number NAD0014B
See Package Number NAC0014A
Schematic Diagram
(Each Amplifier)
2Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS(1)(2)
LM124-N/LM224- LM2902-N
N/LM324-N
LM124A/LM224A/LM324
A
Supply Voltage, V+32V 26V
Differential Input Voltage 32V 26V
Input Voltage −0.3V to +32V −0.3V to +26V
Input Current (VIN <−0.3V)(3) 50 mA 50 mA
Power Dissipation(4) PDIP 1130 mW 1130 mW
CDIP 1260 mW 1260 mW
SOIC Package 800 mW 800 mW
Output Short-Circuit to GND (One Amplifier)(5)
V+≤15V and TA= 25°C Continuous Continuous
Operating Temperature Range −40°C to +85°C
LM324-N/LM324A 0°C to +70°C
LM224-N/LM224A −25°C to +85°C
LM124-N/LM124A −55°C to +125°C
Storage Temperature Range −65°C to +150°C −65°C to
+150°C
Lead Temperature (Soldering, 10 seconds) 260°C 260°C
Soldering Information Dual-In-Line Package Soldering (10 seconds) 260°C 260°C
Small Outline Package Vapor Phase (60 seconds) 215°C 215°C
Infrared (15 seconds) 220°C 220°C
ESD Tolerance(6) 250V 250V
(1) Refer to RETS124AX for LM124A military specifications and refer to RETS124X for LM124-N military specifications.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/
(3) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).
(4) For operating at high temperatures, the LM324-N/LM324A/LM2902-N must be derated based on a +125°C maximum junction
temperature and a thermal resistance of 88°C/W which applies for the device soldered in a printed circuit board, operating in a still air
ambient. The LM224-N/LM224A and LM124-N/LM124A can be derated based on a +150°C maximum junction temperature. The
dissipation is the total of all four amplifiers—use external resistors, where possible, to allow the amplifier to saturate of to reduce the
power which is dissipated in the integrated circuit.
(5) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(6) Human body model, 1.5 kΩin series with 100 pF.
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
ELECTRICAL CHARACTERISTICS
V+= +5.0V, (1), unless otherwise stated LM124A LM224A LM324A
Parameter Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage TA= 25°C(2) 1 2 1 3 2 3 mV
Input Bias Current(3) IIN(+) or IIN(−), VCM = 0V, 20 50 40 80 45 100 nA
TA= 25°C
Input Offset Current IIN(+) or IIN(−), VCM = 0V, 2 10 2 15 5 30 nA
TA= 25°C
Input Common-Mode V+= 30V, (LM2902-N, V+= 26V), 0 V+−1.5 0 V+−1.5 0 V+−1.5 V
Voltage Range(4) TA= 25°C
Supply Current Over Full Temperature Range
RL=∞On All Op Amps mA
V+= 30V (LM2902-N V+= 26V) 1.5 3 1.5 3 1.5 3
V+= 5V 0.7 1.2 0.7 1.2 0.7 1.2
Large Signal V+= 15V, RL≥2kΩ, 50 100 50 100 25 100 V/mV
Voltage Gain (VO= 1V to 11V), TA= 25°C
Common-Mode DC, VCM = 0V to V+−1.5V, 70 85 70 85 65 85 dB
Rejection Ratio TA= 25°C
Power Supply V+= 5V to 30V
Rejection Ratio (LM2902-N, V+= 5V to 26V), 65 100 65 100 65 100 dB
TA= 25°C
Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA= 25°C −120 −120 −120 dB
Coupling(5) (Input Referred)
Output Current Source VIN+= 1V, VIN−= 0V, 20 40 20 40 20 40
V+= 15V, VO= 2V, TA= 25°C mA
Sink VIN−= 1V, VIN+= 0V, 10 20 10 20 10 20
V+= 15V, VO= 2V, TA= 25°C
VIN−= 1V, VIN+= 0V, 12 50 12 50 12 50 μA
V+= 15V, VO= 200 mV, TA= 25°C
Short Circuit to Ground V+= 15V, TA= 25°C(6) 40 60 40 60 40 60 mA
Input Offset Voltage See(2) 4 4 5 mV
VOS Drift RS= 0Ω7 20 7 20 7 30 μV/°C
Input Offset Current IIN(+) −IIN(−), VCM = 0V 30 30 75 nA
IOS Drift RS= 0Ω10 200 10 200 10 300 pA/°C
Input Bias Current IIN(+) or IIN(−)40 100 40 100 40 200 nA
Input Common-Mode V+= +30V 0 V+−2 0 V+−2 0 V+−2 V
Voltage Range(4) (LM2902-N, V+= 26V)
(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature
specifications are limited to −25°C ≤TA≤+85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤TA≤+70°C, and
the LM2902-N specifications are limited to −40°C ≤TA≤+85°C.
(2) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) for LM2902-N, V+from 5V to
26V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V
for LM2902-N), independent of the magnitude of V+.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(6) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
4Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
ELECTRICAL CHARACTERISTICS (continued)
V+= +5.0V, (1), unless otherwise stated LM124A LM224A LM324A
Parameter Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Large Signal V+= +15V (VOSwing = 1V to 11V)
Voltage Gain RL≥2 kΩ25 25 15 V/mV
Output Voltage VOH V+= 30V RL= 2 kΩ26 26 26 V
Swing (LM2902-N, V+= 26V) RL= 10 kΩ27 28 27 28 27 28
VOL V+= 5V, RL= 10 kΩ5 20 5 20 5 20 mV
Output Current Source VO= 2V VIN+= +1V, 10 20 10 20 10 20
VIN−= 0V,
V+= 15V mA
Sink VIN−= +1V, 10 15 5 8 5 8
VIN+= 0V,
V+= 15V
ELECTRICAL CHARACTERISTICS
V+= +5.0V, (1), unless otherwise stated LM124-N/LM224-N LM324-N LM2902-N
Parameter Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage TA= 25°C(2) 2 5 2 7 2 7 mV
Input Bias Current(3) IIN(+) or IIN(−), VCM = 0V, 45 150 45 250 45 250 nA
TA= 25°C
Input Offset Current IIN(+) or IIN(−), VCM = 0V, 3 30 5 50 5 50 nA
TA= 25°C
Input Common-Mode V+= 30V, (LM2902-N, V+= 26V), 0 V+−1.5 0 V+−1.5 0 V+−1.5 V
Voltage Range(4) TA= 25°C
Supply Current Over Full Temperature Range
RL=∞On All Op Amps mA
V+= 30V (LM2902-N V+= 26V) 1.5 3 1.5 3 1.5 3
V+= 5V 0.7 1.2 0.7 1.2 0.7 1.2
Large Signal V+= 15V, RL≥2kΩ, 50 100 25 100 25 100 V/mV
Voltage Gain (VO= 1V to 11V), TA= 25°C
Common-Mode DC, VCM = 0V to V+−1.5V, 70 85 65 85 50 70 dB
Rejection Ratio TA= 25°C
Power Supply V+= 5V to 30V
Rejection Ratio (LM2902-N, V+= 5V to 26V), 65 100 65 100 50 100 dB
TA= 25°C
Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA= 25°C −120 −120 −120 dB
Coupling(5) (Input Referred)
(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature
specifications are limited to −25°C ≤TA≤+85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤TA≤+70°C, and
the LM2902-N specifications are limited to −40°C ≤TA≤+85°C.
(2) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) for LM2902-N, V+from 5V to
26V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V
for LM2902-N), independent of the magnitude of V+.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
V+= +5.0V, (1), unless otherwise stated LM124-N/LM224-N LM324-N LM2902-N
Parameter Conditions Units
Min Typ Max Min Typ Max Min Typ Max
Output Current Source VIN+= 1V, VIN−= 0V, 20 40 20 40 20 40
V+= 15V, VO= 2V, TA= 25°C mA
Sink VIN−= 1V, VIN+= 0V, 10 20 10 20 10 20
V+= 15V, VO= 2V, TA= 25°C
VIN−= 1V, VIN+= 0V, 12 50 12 50 12 50 μA
V+= 15V, VO= 200 mV, TA= 25°C
Short Circuit to Ground V+= 15V, TA= 25°C(6) 40 60 40 60 40 60 mA
Input Offset Voltage See(2) 7 9 10 mV
VOS Drift RS= 0Ω7 7 7 μV/°C
Input Offset Current IIN(+) −IIN(−), VCM = 0V 100 150 45 200 nA
IOS Drift RS= 0Ω10 10 10 pA/°C
Input Bias Current IIN(+) or IIN(−)40 300 40 500 40 500 nA
Input Common-Mode V+= +30V 0 V+−2 0 V+−2 0 V+−2 V
Voltage Range(4) (LM2902-N, V+= 26V)
Large Signal V+= +15V (VOSwing = 1V to 11V)
Voltage Gain RL≥2 kΩ25 15 15 V/mV
Output Voltage VOH V+= 30V RL= 2 kΩ26 26 22 V
Swing (LM2902-N, V+= 26V) RL= 10 kΩ27 28 27 28 23 24
VOL V+= 5V, RL= 10 kΩ5 20 5 20 5 100 mV
Output Current Source VO= 2V VIN+= +1V, 10 20 10 20 10 20
VIN−= 0V,
V+= 15V mA
Sink VIN−= +1V, 5 8 5 8 5 8
VIN+= 0V,
V+= 15V
(6) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
6Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
TYPICAL PERFORMANCE CHARACTERISTICS
Input Voltage Range Input Current
Figure 3. Figure 4.
Supply Current Voltage Gain
Figure 5. Figure 6.
Open Loop Frequency Common Mode Rejection
Response Ratio
Figure 7. Figure 8.
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Voltage Follower Pulse Voltage Follower Pulse
Response Response (Small Signal)
Figure 9. Figure 10.
Large Signal Frequency Output Characteristics
Response Current Sourcing
Figure 11. Figure 12.
Output Characteristics
Current Sinking Current Limiting
Figure 13. Figure 14.
8Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Input Current (LM2902-N only) Voltage Gain (LM2902-N only)
Figure 15. Figure 16.
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
APPLICATION HINTS
The LM124-N series are op amps which operate with only a single power supply voltage, have true-differential
inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate
over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier
operation is possible down to a minimum supply voltage of 2.3 VDC.
The pinouts of the package have been designed to simplify PC board layouts. Inverting inputs are adjacent to
outputs for all of the amplifiers and the outputs have also been placed at the corners of the package (pins 1, 7, 8,
and 14).
Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in
polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge
through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a
destroyed unit.
Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes
are not needed, no large input currents result from large differential input voltages. The differential input voltage
may be larger than V+without damaging the device. Protection should be provided to prevent the input voltages
from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal
can be used.
To reduce the power supply drain, the amplifiers have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output
currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power
capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be
used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover
distortion.
Where the load is directly coupled, as in dc applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values
of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop
gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.
The bias network of the LM124-N establishes a drain current which is independent of the magnitude of the power
supply voltage over the range of from 3 VDC to 30 VDC.
Output short circuits either to ground or to the positive power supply should be of short time duration. Units can
be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase
in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct
short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the
amplifiers. The larger value of output source current which is available at 25°C provides a larger output current
capability at elevated temperatures (see TYPICAL PERFORMANCE CHARACTERISTICS) than a standard IC
op amp.
The circuits presented in the section on Typical Single-Supply Applications emphasize operation on only a single
power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be
used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and
below this value in single power supply systems. Many application circuits are shown which take advantage of
the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required
and input voltages which range to ground can easily be accommodated.
10 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
Typical Single-Supply Applications
(V+= 5.0 VDC)
*R not needed due to temperature independent IIN
Figure 17. Non-Inverting DC Gain (0V Input = 0V Output)
Where: V0= V1+ V2−V3−V4
(V1+ V2)≥(V3+ V4) to keep VO> 0 VDC
Figure 18. DC Summing Amplifier
(VIN'S ≥0 VDC and VO≥VDC)
V0= 0 VDC for VIN = 0 VDC
AV= 10
Figure 19. Power Amplifier
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
(V+= 5.0 VDC)
Figure 20. LED Driver
fo= 1 kHz
Q = 50
AV= 100 (40 dB)
Figure 21. “BI-QUAD” RC Active Bandpass Filter
12 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
(V+= 5.0 VDC)
*(Increase R1 for ILsmall)
Figure 24. Current Monitor
Figure 25. Driving TTL
Figure 26. Voltage Follower
14 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
(V+= 5.0 VDC)
Figure 27.
Figure 28. Pulse Generator
Figure 29. Squarewave Oscillator
Figure 30. Pulse Generator
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
(V+= 5.0 VDC)
IO= 1 amp/volt VIN
(Increase REfor Iosmall)
Figure 31. High Compliance Current Sink
Figure 32. Low Drift Peak Detector
Figure 33. Comparator with Hysteresis
16 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
(V+= 5.0 VDC)
VO= VR
Figure 34. Ground Referencing a Differential Input Signal
*Wide control voltage range: 0 VDC ≤VC≤2 (V+−1.5 VDC)
Figure 35. Voltage Controlled Oscillator Circuit
Figure 36. Photo Voltaic-Cell Amplifier
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
(V+= 5.0 VDC)
Figure 37. AC Coupled Inverting Amplifier
Figure 38. AC Coupled Non-Inverting Amplifier
18 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
(V+= 5.0 VDC)
fO= 1 kHz
Q = 1
AV= 2
Figure 39. DC Coupled Low-Pass RC Active Filter
Figure 40. High Input Z, DC Differential Amplifier
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
www.ti.com
(V+= 5.0 VDC)
Figure 41. High Input Z Adjustable-Gain DC Instrumentation Amplifier
Figure 42. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)
20 Submit Documentation Feedback Copyright © 2004, Texas Instruments Incorporated
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004
(V+= 5.0 VDC)
Figure 43. Bridge Current Amplifier
fO= 1 kHz
Q = 25
Figure 44. Bandpass Active Filter
Copyright © 2004, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM124AJ/PB ACTIVE CDIP J 14 25 TBD Call TI Call TI LM124AJ
LM124J/PB ACTIVE CDIP J 14 25 TBD Call TI Call TI LM124J
LM224J ACTIVE CDIP J 14 25 TBD Call TI Call TI -25 to 85 LM224J
LM2902M NRND SOIC D 14 55 TBD Call TI Call TI -40 to 85 LM2902M
LM2902M/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM2902M
LM2902MT NRND TSSOP PW 14 94 TBD Call TI Call TI -40 to 85 LM290
2MT
LM2902MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM290
2MT
LM2902MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM290
2MT
LM2902MX NRND SOIC D 14 2500 TBD Call TI Call TI -40 to 85 LM2902M
LM2902MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LM2902M
LM2902N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-NA-UNLIM -40 to 85 LM2902N
LM2902N/PB NRND PDIP NFF 14 25 TBD Call TI Call TI LM2902N
LM324AM NRND SOIC D 14 55 TBD Call TI Call TI 0 to 70 LM324AM
LM324AM/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM324AM
LM324AMX NRND SOIC D 14 2500 TBD Call TI Call TI 0 to 70 LM324AM
LM324AMX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM324AM
LM324AN/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-NA-UNLIM 0 to 70 LM324AN
LM324AN/PB NRND PDIP NFF 14 25 TBD Call TI Call TI LM324AN
LM324J ACTIVE CDIP J 14 25 TBD Call TI Call TI 0 to 70 LM324J
LM324M NRND SOIC D 14 55 TBD Call TI Call TI 0 to 70 LM324M
LM324M/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM324M
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM324MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM324
MT
LM324MTX NRND TSSOP PW 14 2500 TBD Call TI Call TI 0 to 70 LM324
MT
LM324MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM324
MT
LM324MX NRND SOIC D 14 2500 TBD Call TI Call TI 0 to 70 LM324M
LM324MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) SN | CU SN Level-1-260C-UNLIM 0 to 70 LM324M
LM324N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM 0 to 70 LM324N
LM324N/PB NRND PDIP NFF 14 25 TBD Call TI Call TI LM324N
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 3
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2902MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1
LM2902MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LM2902MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LM324AMX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LM324AMX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LM324MTX TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1
LM324MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1
LM324MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
LM324MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2902MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0
LM2902MX SOIC D 14 2500 367.0 367.0 35.0
LM2902MX/NOPB SOIC D 14 2500 367.0 367.0 35.0
LM324AMX SOIC D 14 2500 367.0 367.0 35.0
LM324AMX/NOPB SOIC D 14 2500 367.0 367.0 35.0
LM324MTX TSSOP PW 14 2500 367.0 367.0 35.0
LM324MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0
LM324MX SOIC D 14 2500 367.0 367.0 35.0
LM324MX/NOPB SOIC D 14 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
MECHANICAL DATA
N0014A
www.ti.com
N14A (Rev G)
NFF0014A
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
