ADC0820
8-Bit High Speed µP Compatible A/D Converter with
Track/Hold Function
General Description
By using a half-flash conversion technique, the 8-bit
ADC0820 CMOS A/D offers a 1.5 µs conversion time and
dissipates only 75 mW of power. The half-flash technique
consists of 32 comparators, a most significant 4-bitADC and
a least significant 4-bit ADC.
The input to the ADC0820 is tracked and held by the input
sampling circuitry eliminating the need for an external
sample-and-hold for signals moving at less than 100 mV/µs.
For ease of interface to microprocessors, the ADC0820 has
been designed to appear as a memory location or I/O port
without the need for external interfacing logic.
Key Specifications
nResolution 8 Bits
nConversion Time 2.5 µs Max (RD Mode)
1.5 µs Max (WR-RD Mode)
nLow Power 75 mW Max
nTotal Unadjusted
Error ±
1
2
LSB and ±1 LSB
Features
nBuilt-in track-and-hold function
nNo missing codes
nNo external clocking
nSingle supply5 V
DC
nEasy interface to all microprocessors, or operates
stand-alone
nLatched TRI-STATE®output
nLogic inputs and outputs meet both MOS and T
2
L
voltage level specifications
nOperates ratiometrically or with any reference value
equal to or less than V
CC
n0V to 5V analog input voltage range with single 5V
supply
nNo zero or full-scale adjust required
nOverflow output available for cascading
n0.3" standard width 20-pin DIP
n20-pin molded chip carrier package
n20-pin small outline package
n20-pin shrink small outline package (SSOP)
Connection and Functional Diagrams
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
Dual-In-Line, Small Outline
and SSOP Packages
DS005501-1
Top View
Molded Chip Carrier
Package
DS005501-33
June 1999
ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function
© 1999 National Semiconductor Corporation DS005501 www.national.com
Connection and Functional Diagrams (Continued)
Ordering Information
Part Number Total Package Temperature
Unadjusted Error Range
ADC0820BCV V20AMolded Chip Carrier 0˚C to +70˚C
ADC0820BCWM ±
1
2
LSB M20BWide Body Small Outline 0˚C to +70˚C
ADC0820BCN N20AMolded DIP 0˚C to +70˚C
ADC0820CCJ
±1 LSB
J20ACerdip −40˚C to +85˚C
ADC0820CCWM M20BWide Body Small Outline 0˚C to +70˚C
ADC0820CIWM M20BWide Body Small Outline −40˚C to +85˚C
ADC0820CCN N20AMolded DIP 0˚C to +70˚C
DS005501-2
FIGURE 1.
www.national.com 2
Absolute Maximum Ratings (Notes 1, 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V
CC
) 10V
Logic Control Inputs −0.2V to V
CC
+0.2V
Voltage at Other Inputs and Output −0.2V to V
CC
+0.2V
Storage Temperature Range −65˚C to +150˚C
Package Dissipation at T
A
=25˚C 875 mW
Input Current at Any Pin (Note 5) 1 mA
Package Input Current (Note 5) 4 mA
ESD Susceptability (Note 9) 1200V
Lead Temp. (Soldering, 10 sec.)
Dual-In-Line Package (plastic) 260˚C
Dual-In-Line Package (ceramic) 300˚C
Surface Mount Package
Vapor Phase (60 sec.) 215˚C
Infrared (15 sec.) 220˚C
Operating Ratings (Notes 1, 2)
Temperature Range T
MIN
T
A
T
MAX
ADC0820CCJ −40˚CT
A
+85˚C
ADC0820CIWM −40˚CT
A
+85˚C
ADC0820BCN, ADC0820CCN 0˚CT
A
70˚C
ADC0820BCV 0˚CT
A
70˚C
ADC0820BCWM, ADC0820CCWM 0˚CT
A
70˚C
V
CC
Range 4.5V to 8V
Converter Characteristics
The following specifications apply for RD mode (pin 7=0), V
CC
=5V, V
REF
(+)=5V,and V
REF
(−)=GND unless otherwise speci-
fied. Boldface limits apply from T
MIN
to T
MAX
; all other limits T
A
=T
j
=25˚C.
Parameter Conditions ADC0820BCN, ADC0820CCN Limit
Units
ADC0820CCJ ADC0820BCV, ADC0820BCWM
ADC0820CCWM, ADC0820CIWM
Typ Tested Design Typ Tested Design
(Note 6) Limit Limit (Note 6) Limit Limit
(Note 7) (Note 8) (Note 7) (Note 8)
Resolution 888Bits
Total Unadjusted ADC0820BCN, BCWM ±
1
2
±
1
2
LSB
Error ADC0820CCJ ±1LSB
(Note 3) ADC0820CCN, CCWM, CIWM, ±1±1LSB
ADC0820CCMSA ±1±1LSB
Minimum Reference 2.3 1.00 2.3 1.2 k
Resistance
Maximum Reference 2.3 62.3 5.3 6k
Resistance
Maximum VREF(+) VCC VCC VCC V
Input Voltage
Minimum VREF(−) GND GND GND V
Input Voltage
Minimum VREF(+) VREF(−) VREF(−) VREF(−) V
Input Voltage
Maximum VREF(−) VREF(+) VREF(+) VREF(+) V
Input Voltage
Maximum VIN Input VCC+0.1 VCC+0.1 VCC+0.1 V
Voltage
Minimum VIN Input GND−0.1 GND−0.1 GND−0.1 V
Voltage
Maximum Analog CS =VCC
Input Leakage VIN=VCC 30.3 3µA
Current VIN=GND −3 −0.3 −3 µA
Power Supply VCC=5V±5%±1/16 ±
1
4
±1/16 ±
1
4
±
1
4
LSB
Sensitivity
www.national.com3
DC Electrical Characteristics
The following specifications apply for V
CC
=5V, unless otherwise specified. Boldface limits apply from T
MIN
to T
MAX
; all other
limits T
A
=T
J
=25˚C.
Parameter Conditions ADC0820BCN, ADC0820CCN Limit
Units
ADC0820CCJ ADC0820BCV, ADC0820BCWM
ADC0820CCWM, ADC0820CIWM
Typ Tested Design Typ Tested Design
(Note 6) Limit Limit (Note 6) Limit Limit
(Note 7) (Note 8) (Note 7) (Note 8)
VIN(1), Logical “1” VCC=5.25V CS , WR , RD 2.0 2.0 2.0 V
Input Voltage Mode 3.5 3.5 3.5 V
VIN(0), Logical “0” VCC=4.75V CS , WR , RD 0.8 0.8 0.8 V
Input Voltage Mode 1.5 1.5 1.5 V
IIN(1), Logical “1” VIN(1)=5V; CS , RD 0.005 10.005 1µA
Input Current VIN(1)=5V; WR 0.1 30.1 0.3 3µA
VIN(1)=5V; Mode 50 200 50 170 200 µA
IIN(0), Logical “0” VIN(0)=0V;CS,RD,WR, −0.005 −1 −0.005 −1 µA
Input Current Mode
VOUT(1), Logical “1” VCC=4.75V, IOUT=−360 µA; 2.4 2.8 2.4 V
Output Voltage DB0–DB7, OFL , INT
VCC=4.75V, IOUT=−10 µA; 4.5 4.6 4.5 V
DB0–DB7, OFL , INT
VOUT(0), Logical “0” VCC=4.75V, IOUT=1.6 mA; 0.4 0.34 0.4 V
Output Voltage DB0–DB7, OFL , INT , RDY
IOUT, TRI-STATE VOUT=5V; DB0–DB7, RDY 0.1 30.1 0.3 3µA
Output Current VOUT=0V; DB0–DB7, RDY −0.1 −3 −0.1 −0.3 −3 µA
ISOURCE, Output VOUT=0V; DB0–DB7, OFL −12 −6 −12 −7.2 −6 mA
Source Current INT −9 −4.0 −9 −5.3 −4.0 mA
ISINK, Output Sink VOUT=5V; DB0–DB7, OFL , 14 714 8.4 7mA
Current INT , RDY
ICC, Supply Current CS =WR =RD =0 7.5 15 7.5 13 15 mA
AC Electrical Characteristics
The following specifications apply for V
CC
=5V, t
r
=t
f
=20 ns, V
REF
(+)=5V, V
REF
(−)=0V and T
A
=25˚C unless otherwise speci-
fied.
Typ Tested Design
Parameter Conditions (Note 6) Limit Limit Units
(Note 7) (Note 8)
t
CRD
, Conversion Time for RD
Mode Pin 7 =0,
Figure 2
1.6 2.5 µs
t
ACC0
, Access Time (Delay from Pin 7 =0,
Figure 2
t
CRD
+20 t
CRD
+50 ns
Falling Edge of RD to Output
Valid)
t
CWR-RD
, Conversion Time for Pin 7 =V
CC
;t
WR
=600 ns, 1.52 µs
WR-RD Mode t
RD
=600 ns;
Figures 3, 4
t
WR
, Write Time Min Pin 7 =V
CC
;
Figures 3, 4
600 ns
Max (Note 4) See Graph 50 µs
t
RD
, Read Time Min Pin 7 =V
CC
;
Figures 3, 4
600 ns
(Note 4) See Graph
t
ACC1
, Access Time (Delay from Pin 7 =V
CC
,t
RD
<t
I
;
Figure 3
Falling Edge of RD to Output
Valid) C
L
=15 pF 190 280 ns
C
L
=100 pF 210 320 ns
www.national.com 4
AC Electrical Characteristics (Continued)
The following specifications apply for V
CC
=5V, t
r
=t
f
=20 ns, V
REF
(+)=5V, V
REF
(−)=0V and T
A
=25˚C unless otherwise speci-
fied.
Typ Tested Design
Parameter Conditions (Note 6) Limit Limit Units
(Note 7) (Note 8)
t
ACC2
, Access Time (Delay from
Falling Edge of RD to Output
Valid)
Pin 7 =V
CC
,t
RD
>t
I
;
Figure 4
C
L
=15 pF 70 120 ns
C
L
=100 pF 90 150 ns
t
ACC3
, Access Time (Delay from
Rising Edge of RDY to Output
Valid)
R
PULLUP
=1k and C
L
=15 pF 30 ns
t
I
, Internal Comparison Time Pin 7=V
CC
;
Figures 4, 5
800 1300 ns
C
L
=50 pF
t
1H
,t
0H
, TRI-STATE Control R
L
=1k, C
L
=10 pF 100 200 ns
(Delay from Rising Edge of RD to
Hi-Z State)
t
INTL
, Delay from Rising Edge of Pin 7 =V
CC
,C
L
=50 pF
WR to Falling Edge of INT t
RD
>t
I
;
Figure 4
t
I
ns
t
RD
<t
I
;
Figure 3
t
RD
+200 t
RD
+290 ns
t
INTH
, Delay from Rising Edge of
Figures 2, 3, 4
125 225 ns
RD to Rising Edge of INT C
L
=50 pFc
t
INTHWR
, Delay from Rising Edge of
Figure 5
,C
L
=
50 pF 175 270 ns
WR to Rising Edge of INT
t
RDY
, Delay from CS to RDY
Figure 2
,C
L
=
50 pF, Pin 7 =0 50 100 ns
t
ID
, Delay from INT to Output Valid
Figure 5
20 50 ns
t
RI
, Delay from RD to INT Pin 7=V
CC
,t
RD
<t
I
200 290 ns
Figure 3
t
P
, Delay from End of Conversion
Figures 2, 3, 4, 5
500 ns
to Next Conversion (Note 4) See Graph
Slew Rate, Tracking 0.1 V/µs
C
VIN
, Analog Input Capacitance 45 pF
C
OUT
, Logic Output Capacitance 5 pF
C
IN
, Logic Input Capacitance 5 pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC andAC electrical specifications do not apply when operating
the device beyond its specified operating conditions.
Note 2: All voltages are measured with respect to the GND pin, unless otherwise specified.
Note 3: Total unadjusted error includes offset, full-scale, and linearity errors.
Note 4: Accuracy may degrade if tWR or tRD is shorter than the minimum value specified. See Accuracy vs tWR and Accuracy vs tRD graphs.
Note 5: When the input voltage (VIN) at any pin exceeds the power supply rails (VIN <Vor VIN >V+) the absolute value of current at that pin should be limited to
1 mA or less. The 4 mA package input current limits the number of pins that can exceed the power supply boundaries witha1mAcurrent limit to four.
Note 6: Typicals are at 25˚C and represent most likely parametric norm.
Note 7: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: Design limits are guaranteed but not 100%tested. These limits are not used to calculate outgoing quality levels.
Note 9: Human body model, 100 pF discharaged through a 1.5 kresistor.
www.national.com5
TRI-STATE Test Circuits and Waveforms
Timing Diagrams
t
1H
DS005501-3 DS005501-4
tr=20 ns
t
0H
DS005501-5
DS005501-6
tr=20 ns
DS005501-7
Note: On power-up the state of INT can be high or low.
FIGURE 2. RD Mode (Pin 7 is Low)
www.national.com 6
Timing Diagrams (Continued)
DS005501-8
FIGURE 3. WR-RD Mode (Pin 7 is High and t
RD
<t
I
)
DS005501-9
FIGURE 4. WR-RD Mode (Pin 7 is High and t
RD
>t
I
)
DS005501-10
FIGURE 5. WR-RD Mode (Pin 7 is High)
Stand-Alone Operation
www.national.com7
Typical Performance Characteristics
Logic Input Threshold
Voltage vs Supply Voltage
DS005501-34
Conversion Time (RD Mode)
vs Temperature
DS005501-35
Power Supply Current vs
Temperature (not including
reference ladder)
DS005501-36
Accuracy vs t
WR
DS005501-37
Accuracy vs t
RD
DS005501-38
Accuracy vs t
p
DS005501-39
Accuracy vs V
REF
[V
REF
=V
REF
(+)-V
REF
(-)]
DS005501-40
t
I
, Internal Time Delay vs
Temperature
DS005501-41
Output Current vs
Temperature
DS005501-42
www.national.com 8
Description of Pin Functions
Pin Name Function
1V
IN
Analog input; range =GNDV
IN
V
CC
2 DB0 TRI-STATE data outputbit 0 (LSB)
3 DB1 TRI-STATE data outputbit 1
4 DB2 TRI-STATE data outputbit 2
5 DB3 TRI-STATE data outputbit 3
6WR
/RDY WR-RD Mode
WR: With CS low, the conversion is
started on the falling edge of WR.
Approximately 800 ns (the preset internal
time out, t
I
) after the WR rising edge, the
result of the conversion will be strobed
into the output latch, provided that RD
does not occur prior to this time out (see
Figures 3, 4
).
RD Mode
RDY: This is an open drain output (no
internal pull-up device). RDY will go low
after the falling edge of CS; RDY will go
TRI-STATE when the result of the
conversion is strobed into the output
latch. It is used to simplify the interface
to a microprocessor system (see
Figure
2
).
7 Mode Mode: Mode selection input it is
internally tied to GND through a 50 µA
current source.
RD Mode: When mode is low
WR-RD Mode: When mode is high
8RD WR-RD Mode
With CS low, the TRI-STATE data
outputs (DB0-DB7) will be activated
when RD goes low (see
Figure 5
). RD
can also be used to increase the speed
of the converter by reading data prior to
the preset internal time out (t
I
,z800 ns).
If this is done, the data result transferred
to output latch is latched after the falling
edge of the RD (see
Figures 3, 4
).
RD Mode
With CS low, the conversion will start
with RD going low, also RD will enable
the TRI-STATE data outputs at the
completion of the conversion. RDY going
TRI-STATE and INT going low indicates
the completion of the conversion (see
Figure 2
).
Pin Name Function
9 INT WR-RD Mode
INT going low indicates that the
conversion is completed and the data
result is in the output latch. INT will go
low, z800 ns (the preset internal time
out, t
I
) after the rising edge of WR (see
Figure 4
); or INT will go low after the
falling edge of RD , if RD goes low prior
to the 800 ns time out (see
Figure 3
).
INT is reset by the rising edge of RD or
CS (see
Figures 3, 4
).
RD Mode
INT going low indicates that the
conversion is completed and the data
result is in the output latch. INT is reset
by the rising edge of RD or CS (see
Figure 2
).
10 GND Ground
11 V
REF
(−) The bottom of resistor ladder, voltage
range: GNDV
REF
(−)V
REF
(+) (Note 5)
12 V
REF
(+) The top of resistor ladder, voltage range:
V
REF
(−)V
REF
(+)V
CC
(Note 5)
13 CS CS must be low in order for the RD or
WR to be recognized by the converter.
14 DB4 TRI-STATE data outputbit 4
15 DB5 TRI-STATE data outputbit 5
16 DB6 TRI-STATE data outputbit 6
17 DB7 TRI-STATE data outputbit 7 (MSB)
18 OFL Overflow outputIf the analog input is
higher than the V
REF
(+), OFL will be low
at the end of conversion. It can be used
to cascade 2 or more devices to have
more resolution (9, 10-bit). This output is
always active and does not go into
TRI-STATE as DB0–DB7 do.
19 NC No connection
20 V
CC
Power supply voltage
1.0 Functional Description
1.1 GENERAL OPERATION
The ADC0820 uses two 4-bit flash A/D converters to make
an 8-bit measurement (
Figure 1
). Each flash ADC is made
up of 15 comparators which compare the unknown input to a
reference ladder to get a 4-bit result. To take a full 8-bit read-
ing, one flash conversion is done to provide the 4 most sig-
nificant data bits (via the MS flash ADC). Driven by the 4
MSBs, an internal DAC recreates an analog approximation
of the input voltage. This analog signal is then subtracted
from the input, and the difference voltage is converted by a
second 4-bit flash ADC (the LS ADC), providing the 4 least
significant bits of the output data word.
The internal DAC is actually a subsection of the MS flash
converter. This is accomplished by using the same resistor
www.national.com9
1.0 Functional Description (Continued)
ladder for the A/D as well as for generating the DAC signal.
The DAC output is actually the tap on the resistor ladder
which most closely approximates the analog input. In addi-
tion, the “sampled-data” comparators used in the ADC0820
provide the ability to compare the magnitudes of several
analog signals simultaneously, without using input summing
amplifiers. This is especially useful in the LS flash ADC,
where the signal to be converted is an analog difference.
1.2 THE SAMPLED-DATA COMPARATOR
Each comparator in the ADC0820 consists of a CMOS in-
verter with a capacitively coupled input (
Figures 6, 7
). Ana-
log switches connect the two comparator inputs to the input
capacitor (C) and also connect the inverter’s input and out-
put. This device in effect now has one differential input pair.
A comparison requires two cycles, one for zeroing the com-
parator, and another for making the comparison.
In the first cycle, one input switch and the inverter’s feedback
switch (
Figure 6
) are closed. In this interval, C is charged to
the connected input (V1) less the inverter’s bias voltage (V
B
,
approximately 1.2V). In the second cycle (
Figure 7
), these
two switches are opened and the other (V2) input’s switch is
closed. The input capacitor now subtracts its stored voltage
from the second input and the difference is amplified by the
inverter’s open loop gain. The inverter’s input (V
B
') becomes
and the output will go high or low depending on the sign of
V
B
'−V
B
.
The actual circuitry used in the ADC0820 is a simple but im-
portant expansion of the basic comparator described above.
By adding a second capacitor and another set of switches to
the input (
Figure 8
), the scheme can be expanded to make
dual differential comparisons. In this circuit, the feedback
switch and one input switch on each capacitor (Z switches)
are closed in the zeroing cycle. A comparison is then made
by connecting the second input on each capacitor and open-
ing all of the other switches (S switches). The change in volt-
age at the inverter’s input, as a result of the change in charge
on each input capacitor, will now depend on both input signal
differences.
1.3 ARCHITECTURE
In theADC0820, one bank of 15 comparators is used in each
4-bit flash A/D converter (
Figure 12
). The MS (most signifi-
cant) flashADC also has one additional comparator to detect
input overrange. These two sets of comparators operate al-
ternately, with one group in its zeroing cycle while the other
is comparing.
When a typical conversion is started, the WR line is brought
low. At this instant the MS comparators go from zeroing to
comparison mode (
Figure 11
). When WR is returned high
after at least 600 ns, the output from the first set of compara-
tors (the first flash) is decoded and latched. At this point the
two 4-bit converters change modes and the LS (least signifi-
cant) flash ADC enters its compare cycle. No less than 600
ns later, the RD line may be pulled low to latch the lower 4
data bits and finish the 8-bit conversion. When RD goes low,
the flashA/Ds change state once again in preparation for the
next conversion.
Figure 11
also outlines how the converter’s interface timing
relates to its analog input (V
IN
). In WR-RD mode, V
IN
is mea-
DS005501-12
VO=VB
VonC=V1−VB
CS=stray input node capacitor
VB=inverter input bias voltage
Zeroing Phase
FIGURE 6. Sampled-Data Comparator
DS005501-13
Compare Phase
FIGURE 7. Sampled-Data Comparator
DS005501-14
DS005501-45
FIGURE 8. ADC0820 Comparator (from MS Flash ADC)
www.national.com 10
1.0 Functional Description (Continued)
sured while WR is low. In RD mode, sampling occurs during
the first 800 ns of RD. Because of the input connections to
the ADC0820’s LS and MS comparators, the converter has
the ability to sample V
IN
at one instant (Section 2.4), despite
the fact that two separate 4-bit conversions are being done.
More specifically, when WR is low the MS flash is in compare
mode (connected to V
IN
), and the LS flash is in zero mode
(also connected to V
IN
). Therefore both flash ADCs sample
V
IN
at the same time.
1.4 DIGITAL INTERFACE
The ADC0820 has two basic interface modes which are se-
lected by strapping the MODE pin high or low.
RD Mode
With the MODE pin grounded, the converter is set to Read
mode. In this configuration, a complete conversion is done
by pulling RD low until output data appears. An INT line is
provided which goes low at the end of the conversion as well
as a RDY output which can be used to signal a processor
that the converter is busy or can also serve as a system
Transfer Acknowledge signal.
When in RD mode, the comparator phases are internally trig-
gered.At the falling edge of RD, the MS flash converter goes
from zero to compare mode and the LS ADC’s comparators
enter their zero cycle.After 800 ns, data from the MS flash is
latched and the LS flashADC enters compare mode. Follow-
ing another 800 ns, the lower 4 bits are recovered.
WR then RD Mode
With the MODE pin tied high, the A/D will be set up for the
WR-RD mode. Here, a conversion is started with the WR in-
put; however, there are two options for reading the output
data which relate to interface timing. If an interrupt driven
scheme is desired, the user can wait for INT to go low before
reading the conversion result (
Figure 10
). INT will typically
go low 800 ns after WR’s rising edge. However, if a shorter
conversion time is desired, the processor need not wait for
INT and can exercise a read after only 600 ns (
Figure 9
). If
this is done, INT will immediately go low and data will appear
at the outputs.
Stand-Alone
For stand-alone operation in WR-RD mode, CS and RD can
be tied low and a conversion can be started with WR. Data
will be valid approximately 800 ns following WR’s rising
edge.
RD Mode (Pin 7 is Low)
DS005501-16
DS005501-17
FIGURE 9. WR-RD Mode (Pin 7 is High and t
RD
<t
I
)
DS005501-18
FIGURE 10. WR-RD Mode (Pin 7 is High and t
RD
>t
I
)
WR-RD Mode (Pin 7 is High) Stand-Alone Operation
DS005501-19
www.national.com11
1.0 Functional Description (Continued)
OTHER INTERFACE CONSIDERATIONS
In order to maintain conversion accuracy, WR has a maxi-
mum width spec of 50 µs. When the MS flash ADC’s
sampled-data comparators (Section 1.2) are in comparison
mode (WR is low), the input capacitors (C,
Figure 8
) must
hold their charge. Switch leakage and inverter bias current
can cause errors if the comparator is left in this phase for too
long.
Since the MS flash ADC enters its zeroing phase at the end
of a conversion (Section 1.3), a new conversion cannot be
started until this phase is complete. The minimum spec for
this time (t
P
,
Figures 2, 3, 4, 5
) is 500 ns.
DS005501-20
Note: MS means most significant
LS means least significant
FIGURE 11. Operating Sequence (WR-RD Mode)
www.national.com 12
Detailed Block Diagram
DS005501-15
FIGURE 12.
www.national.com13
2.0 Analog Considerations
2.1 REFERENCE AND INPUT
The two V
REF
inputs of theADC0820 are fully differential and
define the zero to full-scale input range of the A to D con-
verter. This allows the designer to easily vary the span of the
analog input since this range will be equivalent to the voltage
difference between V
IN
(+) and V
IN
(−). By reducing
V
REF
(V
REF
=V
REF
(+)−V
REF
(−)) to less than 5V, the sensitivity
of the converter can be increased (i.e., if V
REF
=2V then 1
LSB=7.8 mV). The input/reference arrangement also facili-
tates ratiometric operation and in many cases the chip power
supply can be used for transducer power as well as the V
REF
source.
This reference flexibility lets the input span not only be varied
but also offset from zero. The voltage at V
REF
(−) sets the in-
put level which produces a digital output of all zeroes.
Though V
IN
is not itself differential, the reference design af-
fords nearly differential-input capability for most measure-
ment applications.
Figure 13
shows some of the configura-
tions that are possible.
2.2 INPUT CURRENT
Due to the unique conversion techniques employed by the
ADC0820, the analog input behaves somewhat differently
than in conventional devices. The A/D’s sampled-data com-
parators take varying amounts of input current depending on
which cycle the conversion is in.
The equivalent input circuit of the ADC0820 is shown in
Fig-
ure 14
. When a conversion starts (WR low, WR-RD mode),
all input switches close, connecting V
IN
to thirty-one 1 pF ca-
pacitors. Although the two 4-bit flash circuits are not both in
their compare cycle at the same time, V
IN
still sees all input
capacitors at once. This is because the MS flash converter is
connected to the input during its compare interval and the LS
flash is connected to the input during its zeroing phase (Sec-
tion 1.3). In other words, the LS ADC uses V
IN
as its
zero-phase input.
The input capacitors must charge to the input voltage
through the on resistance of the analog switches (about 5 k
to 10 k). In addition, about 12 pF of input stray capacitance
must also be charged. For large source resistances, the ana-
log input can be modeled as an RC network as shown in
Fig-
ure 15
.AsR
S
increases, it will take longer for the input ca-
pacitance to charge.
In RD mode, the input switches are closed for approximately
800 ns at the start of the conversion. In WR-RD mode, the
time that the switches are closed to allow this charging is the
time that WR is low. Since other factors force this time to be
at least 600 ns, input time constants of 100 ns can be ac-
commodated without special consideration. Typical total in-
put capacitance values of 45 pF allow R
S
to be 1.5 kwith-
out lengthening WR to give V
IN
more time to settle.
External Reference 2.5V Full-Scale
DS005501-21
Power Supply as Reference
DS005501-22
Input Not Referred to GND
DS005501-23
FIGURE 13. Analog Input Options
www.national.com 14
2.0 Analog Considerations (Continued)
2.3 INPUT FILTERING
It should be made clear that transients in the analog input
signal, caused by charging current flowing into V
IN
, will not
degrade the A/D’s performance in most cases. In effect the
ADC0820 does not “look” at the input when these transients
occur. The comparators’ outputs are not latched while WR is
low, so at least 600 ns will be provided to charge the ADC’s
input capacitance. It is therefore not necessary to filter out
these transients by putting an external cap on the V
IN
termi-
nal.
2.4 INHERENT SAMPLE-HOLD
Another benefit of the ADC0820’s input mechanism is its
ability to measure a variety of high speed signals without the
help of an external sample-and-hold. In a conventional SAR
type converter, regardless of its speed, the input must re-
main at least
1
2
LSB stable throughout the conversion pro-
cess if full accuracy is to be maintained. Consequently, for
many high speed signals, this signal must be externally
sampled, and held stationary during the conversion.
Sampled-data comparators, by nature of their input switch-
ing, already accomplish this function to a large degree (Sec-
tion 1.2). Although the conversion time for the ADC0820 is
1.5 µs, the time through which V
IN
must be
1
2
LSB stable is
much smaller. Since the MS flash ADC uses V
IN
as its “com-
pare” input and the LS ADC uses V
IN
as its “zero” input, the
ADC0820 only “samples” V
IN
when WR is low (Sections 1.3
and 2.2). Even though the two flashes are not done simulta-
neously, the analog signal is measured at one instant. The
value of V
IN
approximately 100 ns after the rising edge of
WR (100 ns due to internal logic prop delay) will be the mea-
sured value.
Input signals with slew rates typically below 100 mV/µs can
be converted without error. However, because of the input
time constants, and charge injection through the opened
comparator input switches, faster signals may cause errors.
Still, the ADC0820’s loss in accuracy for a given increase in
signal slope is far less than what would be witnessed in a
conventional successive approximation device.An SAR type
converter with a conversion time as fast as 1 µs would still
not be able to measure a 5V 1 kHz sine wave without the aid
of an external sample-and-hold. TheADC0820, with no such
help, can typically measure 5V, 7 kHz waveforms.
DS005501-24
FIGURE 14.
DS005501-25
FIGURE 15.
www.national.com15
3.0 Typical Applications
8-Bit Resolution Configuration
DS005501-26
9-Bit Resolution Configuration
DS005501-27
www.national.com 16
3.0 Typical Applications (Continued)
Telecom A/D Converter
DS005501-28
V
IN
=3 kHz max ±4V
P
No track-and-hold needed
Low power consumption
Multiple Input Channels
DS005501-29
8-Bit 2-Quadrant Analog Multiplier
DS005501-30
www.national.com17
3.0 Typical Applications (Continued)
Fast Infinite Sample-and-Hold
DS005501-31
www.national.com 18
3.0 Typical Applications (Continued)
Digital Waveform Recorder
DS005501-32
www.national.com19
Physical Dimensions inches (millimeters) unless otherwise noted
Hermetic Dual-In-Line Package (J)
Order Number ADC0820CCJ
NS Package Number J20A
www.national.com 20
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
SO Package (M)
Order Number ADC0820BCWM, ADC0820CCWM or ADC0820CIWM
NS Package Number M20B
Molded Dual-In-Line Package (N)
Order Number ADC0820BCN or ADC0820CCN
NS Package Number N20A
www.national.com21
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
Molded Chip Carrier Package (V)
Order Number ADC0820BCV
NS Package Number V20A
ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.