LTC1153 Auto-Reset Electronic Circuit Breaker U DESCRIPTIO FEATURES Programmable Trip Delay: 15s to >100ms Programmable Trip Current: 1mA to >20A Programmbale Auto-Reset Time: 1ms to >10 sec. 4.5V to 18V Supply Range Drives Low RDS(ON) N-Channel MOSFETs Status Output Indicates Fault Condition Thermal Trip with PTC Thermistor 8A IQ in Standby Mode No External Charge Pump Capacitors Available in 8-Pin SOIC UO APPLICATI Power Bus Circuit Breaker SCSI Termination Power Protection Regulator Over-Current Protection Battery Short-Circuit Protection DC Motor Stall Protection Sensitive System Power Interrupt The trip current, trip delay time and auto-reset period are programmable over a wide range to accommodate a variety of load impedances. An active high shutdown input is also provided and interfaces directly to a PTC thermistor for thermal circuit breaking. An open-drain output is provided to report breaker status to the P. The LTC1153 is available in both 8-pin DIP and 8-pin SOIC packages. UO S The LTC1153 electronic circuit breaker drives a low cost N-channel MOSFET to interrupt power to a sensitive electronic load in the event of an over-current condition. The breaker remains tripped for a period of time set by an external timing capacitor and then is automatically reset. This cycle continues until the over-current condition is removed, protecting both the sensitive load and the MOSFET switch. TYPICAL APPLICATI 5V/1A Electronic Circuit Breaker with 1ms Trip Delay, 200ms Auto-Reset Period and 70C Thermal Shutdown Trip Delay Time 10 IN CT 0.22F Z5U CD RD 0.01F 100k CT *RSEN 0.1 DS LTC1153 TO P STATUS IRLR024 G 51k 51k GND RSEN = 0.1 RD = 100k CD = 0.01F VS SHUTDOWN 5V **70C PTC TRIP DELAY (ms) ON/OFF 1 0.1 SENSITIVE 5V LOAD ALL COMPONENTS SHOWN ARE SURFACE MOUNT. * IMS026 INTERNATIONAL MANUFACTURING SERVICE, INC. (401) 683-9700 ** RL2006-100-70-30-PT1 KEYSTONE CARBON COMPANY (814) 781-1591 0.01 1 10 CIRCUIT BREAKER CURRENT (A) 100 LTC1153 * TA02 LTC1153 * TA01 1 LTC1153 W W W AXI U U ABSOLUTE RATI GS Supply Voltage ........................................................ 22V Input Voltage ..................... (VS + 0.3V) to (GND - 0.3V) Timing Capacitor Voltage ... (VS + 0.3V) to (GND - 0.3V) Gate Voltage ....................... (VS + 24V) to (GND - 0.3V) Status Output Voltage .............................................. 15V Current (Any Pin).................................................. 50mA Operating Temperature LTC1153C .............................................. 0C to 70C Storage Temperature Range ................. - 65c to 150C Lead Temperature (Soldering, 10 sec.)................ 300C U W U PACKAGE/ORDER I FOR ATIO ORDER PART NUMBER TOP VIEW IN 1 8 VS TIMING CAP 2 7 DRAIN SENSE STATUS 3 6 GATE GND 4 5 SHUTDOWN LTC1153CN8 ORDER PART NUMBER TOP VIEW IN 1 8 VS TIMING CAP 2 7 DRAIN SENSE STATUS 3 6 GATE GND 4 5 SHUTDOWN S8 PACKAGE 8-LEAD PLASTIC SOIC N8 PACKAGE 8-LEAD PLASTIC DIP LTC1154 * PO02 LTC1153 * PO01 TJMAX = 100C, JA = 130C/W (N8) LTC1153CS8 S8 PART MARKING TJMAX = 100C, JA = 150C/W 1153 ELECTRICAL CHARACTERISTICS VS = 4.5V to 18V, TA = 25C, CT = 0.1F, VSD = 0V unless otherwise noted. CONDITIONS MIN LTC1153C TYP SYMBOL PARAMETER VS Supply Voltage IQ Quiescent Current OFF VS = 5V, VIN = 0V IQ Quiescent Current ON VS = 5V, VIN = 5V IQ Quiescent Current ON VS =12V, VIN = 5V 180 VINH Input High Voltage VINL Input Low Voltage 0.8 V IIN Input Current 1 A CIN Input Capacitance VCT Timing Capacitor Threshold Voltage VS = 5V VS = 12V ICT Timing Capacitor Current VS = 12V VSDH Shutdown Input High Voltage VSDL Shutdown Input Low Voltage ISD Shutdown Input Current VSEN Drain Sense Threshold Voltage 0V < VIN < VS 0V < VIN < VS 2 Drain Sense Input Current 0V < VSEN < VS V 8 20 A 85 120 A 400 A 2 V pF 2.1 2.0 2.5 2.6 2.9 3.2 V V 3.0 4.2 6.0 A 2 V 0.8 UNITS 18 5 ISEN 4.5 MAX 80 75 100 100 V 1 A 120 125 mV mV 0.1 A LTC1153 ELECTRICAL CHARACTERISTICS VS = 4.5V to 18V, TA = 25C, CT = 0.1F, VSD = 0V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VGATE - VS Gate Voltage Above Supply VS = 5V VS = 6V VS = 12V MIN LTC1153C TYP MAX UNITS 6.0 7.5 15.0 7.0 8.3 18.0 9.0 15.0 25.0 V V V 0.05 0.4 V 1 A VSTAT Status Output Low Voltage ISTAT = 400A ISTAT Status Output Leakage Current VSTAT = 12V tON Turn-ON Time VS = 5V, CGATE = 1000pF Time for VGATE > VS + 2V Time for VGATE > VS + 5V 30 100 110 450 300 1000 s s VS = 12V, CGATE = 1000pF Time for VGATE > VS + 5V Time for VGATE > VS + 10V 20 50 80 160 200 500 s s VS = 5V, CGATE = 1000pF Time for VGATE < 1V 10 36 60 s VS = 12V, CGATE = 1000pF Time for VGATE < 1V 10 28 60 s VS = 5V, CGATE = 1000pF Time for VGATE < 1V 5 25 40 s VS = 12V, CGATE = 1000pF Time for VGATE < 1V 5 23 40 s VS = 5V, CGATE = 1000pF Time for VGATE < 1V 17 40 s VS = 12V, CGATE = 1000pF Time for VGATE < 1V 13 35 s tOFF Turn-OFF Time tTD Minimum Trip Delay tSD Shutdown Turn-OFF Time The denotes specifications which apply over the operating temperature range. U W TYPICAL PERFOR A CE CHARACTERISTICS Standby Supply Current VIN = 0V TA = 25C 24 TA = 25C 900 SUPPLY CURRENT (A) 40 35 30 25 20 15 22 800 20 700 18 VGATE - VS (V) 45 SUPPLY CURRENT (A) MOSFET Switch Gate Voltage Supply Current ON 1000 50 600 500 400 16 14 12 300 10 10 200 8 5 100 6 0 0 4 0 5 10 15 SUPPLY VOLTAGE (V) 20 LTC1153 * TPC01 0 5 10 15 SUPPLY VOLTAGE (V) 20 LTC1153 * TPC02 0 5 10 15 SUPPLY VOLTAGE (V) 20 LTC1153 * TPC03 3 LTC1153 U W TYPICAL PERFOR A CE CHARACTERISTICS Input Threshold Voltage 1.8 1.6 VON 1.4 VOFF 1.2 1.0 0.8 0.6 0.4 5 0 3.3F 130 120 110 100 90 80 CGATE = 1000pF 400 VGS = 5V VGS = 2V 5 CGATE = 1000pF TIME FOR VGATE < 1V 40 35 35 25 20 10 5 5 0 5 0 20 10 15 SUPPLY VOLTAGE (V) 0 900 40 Input ON Threshold Voltage SUPPLY CURRENT (A) 25 20 0 -50 -25 2.4 VIN = 5V 2.2 800 30 VS = 18V 600 500 400 VS = 12V 200 100 VS = 5V 50 25 0 75 TEMPERATURE (C) 700 300 100 125 LTC1153 * TPC10 20 10 15 SUPPLY VOLTAGE (V) LTC1153 * TPC09 Supply Current ON 35 5 LTC1153 * TPC08 VIN = 0V 5 20 15 1000 10 25 10 Standby Supply Current 15 30 15 LTC1153 * TPC07 50 20 CGATE = 1000pF TIME FOR VGATE < 1V VSEN = VS - 1V NO EXTERNAL DELAY 45 30 20 10 15 SUPPLY VOLTAGE (V) 15 Built-In Trip Delay 0 0 0 10 LTC1153 * TPC06 TRIP TIME (s) TURN OFF TIME (s) TURN ON TIME (s) 500 5 SUPPLY VOLTAGE (V) 40 100 SUPPLY CURRENT (A) 0 50 45 800 4 20 10 15 SUPPLY VOLTAGE (V) MOSFET Gate Turn-OFF Time 700 0.1F 0.01 5 50 200 0.1 LTC1153 * TPC05 MOSFET Gate Turn-ON Time 300 0.33F 0.033F 0 1000 600 1F 60 LTC1153 * TPC04 900 1 70 50 20 10 15 SUPPLY VOLTAGE (V) TA = 25C 140 INPUT THRESHOLD VOLTAGE (V) INPUT THRESHOLD VOLTAGE (V) 2.0 10 RESET PERIOD (SEC) DRAIN SENSE THRESHOLD VOLTAGE (mV) 150 2.2 45 Auto-Reset Period Drain Sense Threshold Voltage 2.4 VS = 5V 0 -50 -25 50 25 0 75 TEMPERATURE (C) 2.0 1.8 1.6 1.4 1.2 1.O VS = 5V VS = 18V 0.8 0.6 100 125 LTC1153 * TPC11 0.4 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 LTC1153 * TPC12 LTC1153 U W TYPICAL PERFOR A CE CHARACTERISTICS Shutdown Threshold Voltage Auto-Reset Time* 1000 10 TA = 25C *SECONDS OF DELAY PER F CT 2.2 1.8 1.6 1.4 VS = 5V 1.2 VS = 18V 1.O 0.8 GATE DRIVE CURRENT (A) 2.0 AUTO-RESET TIME (s/F) SHUTDOWN THRESHOLD VOLTAGE (V) 2.4 MOSFET Gate Drive Current VS = 12V VS = 5V 1 VS = 18V 100 VS = 18V VS = 12V 10 VS = 5V 1 0.6 0.4 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 0.1 -50 0.1 -25 0 50 75 25 TEMPERATURE (C) LTC1153 * TPC13 100 125 LTC1153 * TPC14 0 4 8 12 16 GATE VOLTAGE ABOVE SUPPLY (V) 20 LTC1153 * TPC15 U U U PI FU CTIO S Input and Shutdown Pins The LTC1153 input pin is active high and activates all of the protection and charge pump circuitry when switched ON. The shutdown pin is designed to break the circuit if a secondary fault condition (over temperature, etc.) is detected. The LTC1153 logic and shutdown inputs are high impedance CMOS gates with ESD protection diodes to ground and supply and therefore should not be forced beyond the power supply rails. The shutdown pin should be connected to ground when not in use. Timing Capacitor Pin (Auto-Reset Timer) The small capacitor charging current (4.2A) produces large delays with relatively small valued capacitors, but care must be taken to ensure that this current is not shunted to ground through a leaky capacitor or printed circuit board trace. The timing capacitor voltage is sensed by a high impedance CMOS comparator input with ESD clamp diodes to ground and supply and therefore should not be forced beyond the power supply rails. This pin can be grounded if the auto-reset function is not used. MOSFET Gate Drive Pin The MOSFET gate drive pin is either driven to ground when the switch is turned OFF or driven above the supply rail when the switch is turned ON. This pin is a relatively high impedance when driven above the rail (the equivalent of a few hundred k). Care should be taken to minimize any loading of this pin by parasitic resistance to ground or supply. Supply Pin The supply pin of the LTC1153 serves two vital purposes. The first is obvious: it powers the input, gate drive, regulation and protection circuitry. The second purpose is less obvious: it provides a Kelvin connection to the top of the drain sense resistor for the internal 100mV reference. The LTC1153 is designed to be continuously powered so that the gate of the MOSFET is actively driven at all times. If it is necessary to remove power from the supply pin and then re-apply it, the input pin (or enable pin) should be cycled a few milliseconds after the power is re-applied to reset the input latch and protection circuitry. Also, the input and enable pins should be isolated with 10k resistors to limit the current flowing through the ESD protection diodes to the supply pin. The supply pin of the LTC1153 should never be forced below ground as this may result in permanent damage to the device. A 300 resistor should be inserted in series with the ground pin if negative supply voltage transients are anticipated. 5 LTC1153 U U U PI FU CTIO S Drain Sense Pin The drain sense pin is compared against the supply pin voltage. If the voltage at this pin is more than 100mV below the supply pin, the input latch will trip and the MOSFET switch will be turned off. This pin is also a high impedance CMOS gate with ESD protection and therefore should not be forced beyond the power supply rails. Some loads, such as large supply capacitor, lamps, or motors require high inrush currents. An RC time is added between the sense resistor and the drain sense pin to ensure that the drain sense circuitry does not false trigger during start-up. This trip delay can be set from a few microseconds to many seconds. However, very long delays may put the MOSFET switch in risk of being destroyed by a short-circuit condition. (see Applications Information Section). Status Pin The status pin is an open-drain output which is driven low whenever the breaker is tripped. A 51k pull-up resistor should be connected between this output and a logic supply. The status pins of multiple LTC1153s can be OR'd together if independent fault sensing is not required. No connection is required to this pin when not in use. W BLOCK DIAGRA DRAIN SENSE ANALOG SECTION VS LOW STANDBY CURRENT REGULATOR SHUTDOWN TTL-TO-CMOS CONVERTER 10s DELAY COMP 100mV REFERENCE SHUTDOWN GATE CHARGE AND DISCHARGE CONTROL LOGIC ANALOG GATE DIGITAL R INPUT TTL-TO-CMOS CONVERTER VOLTAGE REGULATORS INPUT LATCH ONE SHOT S OSCILLATOR AND CHARGE PUMP FAST/SLOW GATE CHARGE LOGIC GND TIMER CAP STATUS 6 AUTO-RESET TIMER FAULT DETECTION AND STATUS OUTPUT DRIVER LTC1153 * BD01 LTC1153 WU W TI I G DIAGRA TEST CIRCUITS 5V 1 INPUT 51k STATUS 2 0.1F Z5U 3 4 IN VS CT DS 7 CP 0.01F RSEN 0.05 STATUS G SD 6 OVER-CURRENT (AUTO-CURRENT) NORMAL SHUTDOWN OFF INPUT *200s RD100k LTC1153 GND OFF NORMAL 8 OUTPUT IRLZ24 OUTPUT 5 S1 SHUTDOWN 10 1 LTC1153 * TC01 STATUS TIMING CAP *90ms SHUTDOWN LTC1153 * TD01 S1 CLOSED S1 OPEN *TIMES FOR COMPONENTS SHOWN IN TEST CIRCUIT LTC1153 OPERATIO U The LTC1153 is an electronic circuit breaker with built-in MOSFET gate charge pump, over-current detection and auto-reset circuitry. The LTC1153 consists of the following functional blocks: TTL and CMOS Compatible Inputs The LTC1153 input and shutdown input have been designed to accommodate a wide range of logic families. Both input thresholds are set at about 1.3V with approximately 100mV of hysteresis. Internal Voltage Regulation The output of the TTL-to-CMOS converter drives two regulated supplies which power the low voltage CMOS logic and analog blocks. The regulator outputs are isolated from each other so that the noise generated by the charge pump logic is not coupled into the 100mV reference or the analog comparator. Gate Charge Pump A low standby current voltage regulator provides continuous bias for the TTL-to-CMOS converter. The TTL-toCMOS converter output enables the rest of the circuitry. In this way the power consumption is kept to a minimum in the standby mode. Gate drive for the MOSFET switch is produced by an adaptive charge pump circuit which generates a gate voltage substantially higher than the power supply voltage. The charge pump capacitors are included on-chip and therefore no external components are required to generate the gate drive. Auto-Reset Timer Drain Current Sense An external timing capacitor, CT, is ramped up by a small current whenever a fault is detected, i.e., the switch latched off. When the timing capacitor ramps up to approximately 2.5V, the switch is turned back on and the timing capacitor discharged. If the circuit breaker output is still in an overload state, the breaker will latch off and this cycle will continue until the fault condition is removed. The LTC1153 is configured to sense the current flowing into the drain of an N-channel MOSFET switch. An internal 100mV reference is compared to the drop across a sense resistor (typically 0.002 to 0.10) in series with the drain lead. If the drop across this resistor exceeds the internal 100mV threshold, the input latch is reset and the gate is quickly discharged via a relatively large N-channel transistor. 7 LTC1153 LTC1153 OPERATIO U Controlled Gate Rise and Fall Times Status Output Driver When the input is switched ON and OFF, the gate is charged by the internal charge pump and discharged in a controlled manner. The charge and discharge rates have been set to minimize RFI and EMI emissions in normal operation. If a short-circuit or current overload condition is encountered, the gate is discharged very quickly (typically a few microseconds) by a large N-channel transistor. The status circuitry continuously monitors the input and the gate charge control logic. The open-drain output is driven low when the input is turned ON and the breaker is latched off. The status circuitry is reset along with the input latch when the auto-reset circuitry retries the breaker or the input is cycled low. U W U UO APPLICATI S I FOR ATIO 12V MOSFET and Load Protection The LTC1153 protects the power MOSFET switch by removing drive from the gate as soon as an over-current condition is detected and breaking the circuit to the load. Resistive and inductive loads can be protected with no external time delay in series with the drain sense pin. High inrush current loads, however, require that the trip delay time be set long enough to start the load but short enough to ensure the safety of the MOSFET. + 100F IN CT 0.22F VS CT 0.036 DS LTC1153 STATUS G IRFZ24 15V GND SD RLOAD 12 CLOAD 1F Resistive Loads LTC1153 * F01 Loads that are primarily resistive should be protected with as short a delay as possible to minimize the amount of time that the MOSFET switch or the load is subjected to an overload condition. The drain sense circuitry has a builtin trip delay of approximately 10s to eliminate false triggering by power supply or load transient conditions. This delay is sufficient to "mask" short load current transients and the starting of a small capacitor (<1F) in parallel with the load. The drain sense pin can therefore be connected directly to the drain current sense resistor as shown in Figure 1. Inductive Loads Loads that are primarily inductive, such as relays, solenoids and stepper motor windings should be protected with as short a delay as possible to minimize the amount of time that the MOSFET is subjected to an overload condition. The built-in 10s trip delay will ensure that the breaker is not false-tripped by a supply or load transient. No external delay components are required as shown in Figure 2. 8 Figure 1. Protecting Resistive Loads 12V + 100F IN CT 0.22F VS CT 0.036 DS LTC1153 STATUS G IRFZ24 15V GND SD 1N5400 12V, 1A SOLENOID LTC1153 * F02 Figure 2. Protecting Inductive Loads Large inductive loads (>0.1mH) may require diodes connected directly across the inductor to safely divert the stored energy to ground. Many inductive loads have these diodes included. If not, a diode of the proper current rating LTC1153 W U U UO APPLICATI S I FOR ATIO should be connected across the load, as shown in Figure 2, to safely divert the stored energy. Using the values shown in Figure 3, the start-up current is less than 100mA and does not false-trip the breaker. Capacitive Loads Lamp Loads Large capacitive loads, such as complex electrical systems with large bypass capacitors, should be powered using the circuit shown in Figure 3. The gate drive to the power MOSFET switch is passed through an RC delay network, R1 and C1, which greatly reduces the turn on ramp rate of the switch. And since the MOSFET source voltage follows the gate voltage, the load is powered smoothly and slowly from ground. This dramatically reduces the start-up current flowing into the supply capacitor/s which, in turn, reduces supply transients and allows for slower activation of sensitive electrical loads. (Diode, D1, provides a direct path for the LTC1153 protection circuitry to quickly discharge the gate). The inrush current created by a lamp during turn-on can be 10 to 20 times greater than the rated operating current. The circuit shown in Figure 4 shifts the trip threshold up by a factor of 11:1 (to 30A) for 100ms while the bulb is turned on. The trip threshold then drops down to 2.7A after the inrush current has subsided. 12V + 470F IN VS CT CT 0.33F 10k 0.036 100k DS VN2222LL LTC1153 STATUS G 0.1F 1M 12V GND + SD 9.1V 470F IN VS 0.036 CD 0.01F CT 0.47F CT DS GND G RD 1OOk 12V/1A BULB D1 1N4148 LTC1153 STATUS MTP3055EL R1 1OOk LTC1153 * F04 R2 1OOk Figure 4. Lamp Driver with Delayed Protection MTP3055E SD C1 0.33F OUT 15V + CLOAD 100F LTC1153 * F03 Selecting RD and CD Figure 5 is a graph of normalized breaker trip time versus breaker current. This graph is used to select the two delay components, RD and CD, which make up a simple RC delay between the drain sense resistor and the drain sense input. Figure 3. Powering Large Capacitive Loads The RC network, RD and CD, in series with the drain sense input should be set to trip based on the expected characteristics of the load after start-up. With this circuit, it is possible to power a large capacitive load and still react quickly (10s) to break the circuit if a short-circuit condition is encountered. The ramp rate at the output of the switch as it lifts off ground is approximately: TRIP DELAY TIME (1 = RC) 10 1 0.1 dV/dt = (VGATE - VTH)/(R1 x C1) And therefore the current flowing into the capacitor during start-up is approximately: ISTART-UP = CLOAD x dV/dt 0.01 1 10 100 BREAKER CURRENT (1 = SET CURRENT) LTC1153 * F05 Figure 5. Trip Delay Time vs Breaker Current 9 LTC1153 W U U UO APPLICATI S I FOR ATIO The Y axis of the graph is normalized to one RC time constant. The X axis is normalized to the set current. (The set current is defined as the current required to develop 100mV across the drain sense resistor). Note that the trip delay time is shorter for increasing levels of MOSFET current. This ensures that the total energy dissipated by the MOSFET is always within the bounds established by the manufacturer for safe operation. (See MOSFET data sheet for further S.O.A. information). 12V 5V + 120k 10k 10F IN VS 0.05 CT 0.47F 5V P OR CONTROL LOGIC CT DS LTC1153 10k STATUS MTP12N06 G 15V GND SD 10k LOAD 300 Using a Speed-Up Diode LTC1153 * F07 Another way to reduce the trip delay time is to "bypass" the delay resistor with a small signal diode as shown in Figure 6. The diode will engage when the drop across the drain sense resistor exceeds about 0.7V, providing a direct path to the sense pin and dramatically reducing the trip delay time. The drain sense resistor value is selected to limit the maximum DC breaker current to 4A. 12V + 100F IN VS 0.01F CT 0.22F CT 1N4148 0.036 1OOk DS LTC1153 STATUS IRF530 G 15V GND SD LOAD LTC1153 * F06 Figure 7. Reverse Battery Protection Current Limited Power Supplies The LTC1153 requires at least 3.5V at the supply pin to ensure proper operation. It is therefore necessary that the supply to the LTC1153 be held higher than 3.5V at all times, even when the output of the switch is short circuited to ground. The output voltage of a current limited regulator may drop very quickly during short-circuit and pull the supply pin of the LTC1153 below 3.5V before the shutdown circuitry has had time to respond and remove drive from the gate of the power MOSFET. A supply filter should be added as shown in Figure 8 which holds the supply pin of the LTC1153 high long enough for the over-current shutdown circuitry to respond and fully discharge the gate, i.e., break the circuit. >7V 5V/2A REGULATOR + + *20 100F Figure 6. Using a Speed-Up Diode + Reverse Battery Protection IN *47F VS 0.1F The LTC1153 can be protected against reverse battery conditions by connecting a resistor in series with the ground lead as shown in Figure 7. The resistor limits the supply current to less than 50mA with -12V applied. Since the LTC1153 draws very little current while in normal operation, the drop across the ground resistor is minimal. the 5V P (or control logic) is protected by the 10k resistors in series with the input and status pins. 10 CT 0.1 10F 1N4148 100k DS LTC1153 1F STATUS GND IRLR024 G SHORT CIRCUIT SD *SUPPLY FILTER COMPONENTS LTC1153 * F08 Figure 8. Supply Filter for Current Limited Supplies LTC1153 W U U UO APPLICATI S I FOR ATIO Five volt linear regulators with small output capacitors are the most difficult to protect as they can "switch" from a voltage mode to a current limited mode very quickly. The large output capacitors on many switching regulators, on the other hand, may be able to hold the supply pin of the LTC1153 above 3.5V sufficiently long that this extra filtering is not required. Because the LTC1153 is micropower in both the standby and ON state, the voltage drop across the supply filter is less than 2mV, and does not significantly alter the accuracy of the 100mV drain sense threshold voltage. U TYPICAL APPLICATIO S Over-Voltage Circuit Breaker Over-Temperature Circuit Breaker 12V 4.75V TO 5.25V + + 10F 100F 5V 51k IN VS CT DS 0.47F STATUS VS CT DS 5V 100 51k 0.22F 5V LTC1153 IN MTD3055E G LTC1153 STATUS 5.6V IRLD024 G 30k GND GND SD *PTC THERMISTOR (100C) *RL3006-50-100-25-PT0 KEYSTONE 5V LOAD SWITCH IS SHUTDOWN WHEN VS > 5.7V LTC1153 * TA03 24V TO 28V + 100F IN 5V 51k VS CT 0.47F 100F + IN 10F DS CT 51k 0.47F MTP12N06 G VS 5V LTC1153 STATUS + 3k 18V SD *KEYSTONE RL2006-100-100-30-PT. MOUNT ON MOSFET OR LOAD HEAT SINK. + 18V 10F DS STATUS 6.2k 1N4148 G MTP15N06E 30k GND 5V *PTC THERMISTOR (100C) 100k LTC1153 30k GND LTC1153 * TA05 24V to 28V Over-Temperature Circuit Breaker with Bootstrapped Supply 24V to 28V Over-Temperature Circuit Breaker 24V TO 28V SD 12V LOAD 24V TO 28V LOAD LTC1153 * TA04 SD 5V *PTC THERMISTOR (100C) * KEYSTONE RL2006-100-100-30-PT. MOUNT ON MOSFET OR LOAD HEAT SINK. ** BOOTSTRAPPING REDUCES IQ(OFF) TO 60A, IQ(ON) = 1mA. 24V TO 28V LOAD LTC1153 * TA06 11 LTC1153 UO TYPICAL APPLICATI S 12V Lamp Driver/Circuit Breaker with Auto-Reset 12V Relay Driver with Over-Current Protection and Status Feedback 12V + + 100F 470F IN 10k VS 2 0.02 100k IN 5V CT DS 0.33F STATUS G 0.01F CT 1F 0.1F STATUS SD 1N4148 DS MTD3055E LTC1153 1M GND 10k VS 5V VN2222LL LTC1153 G IRFZ34 15V GND 12V SD COIL CURRENT LIMITED TO 350mA CONTACT CURRENT LIMITED TO 5A LTC1153 * TA07 LTC1153 * TA08 SCSI Termination Power 1A Circuit Breaker with Auto-Reset and Ramped Turn-On 0.1 MTD3055EL 1N5817 + 4.25V/1A + 100F 10F 20 10k 1N4148 + ON/OFF IN VS 47F 0.1F 51k CT 0.47F Z5U STATUS 1N4148 DS LTC1153 100k STATUS 100k G 0.22F GND SD LTC1153 * TA09 Logic Controlled Battery Switch with Reverse Battery Protection, Ramped Turn-On and 10A Standby Current Si9956DY 0.05 + + 4 TO 6 CELLS SWITCHED BATTERY 47F/16V ON/OFF IN VS CT DS 51k 0.47F STATUS LTC1153 STATUS 1N4148 100k 100k G 0.22F GND SD LTC1153 * TA10 300 12 TO 12V LOAD 1N4001 12V/2A BULB 5V 0.02 LTC1153 UO TYPICAL APPLICATI S "4 Cell-to-5V" Regulator with 2A Current Limit, Auto-Reset, Ramped Turn-On and 10A Standby Current + + 4-CELL BATTERY PACK 100F ON/OFF IN VS CT DS 51k 0.47F STATUS IRLR024 1N4148 200pF LTC1153 STATUS 0.05 100k 100k 10k 8 G 0.22F GND 1 3 LT1431 7 SD 6 5V/1A 4 + 470F ESR < 0.5 5 LTC1153 * TA11 12V Step-Up Regulator with Soft Start, Auto-Reset Circuit Breaker (Pre-Regulator), Status Feedback and 10A Standby Current 0.02 5V 1N5820 50H IRLZ24 + + 470F 20 100k 1N4148 + + ON/OFF IN VS CT DS 5 150F VSW 4 LT1070 2 FB VC GND 0.22F 51k 0.47F Z5U 1N4148 3 LTC1153 STATUS STATUS GND 100k 330F 10.72k 1% VIN 47F 1 1.24k 1% 100k G 12V/1A 1k 0.22F SD 1F LTC1153 * TA12 12V Step-Up Regulator with 1A Circuit Breaker (Post Regulator), Breaker Status Feedback and Ramped Output 50H 5V 1N5820 (12V) + + 5 150F 330F VIN VSW 4 LT1070 2 FB VC GND 3 1 1k 10.72k 1% ON/OFF IN VS CT 0.47F Z5U STATUS 10k 0.1F 51k 1.24k 1% 0.1 1N4148 DS LTC1153 STATUS 1N4148 100k 100k G IRF530 12V 1F GND SD + 0.22F 12V/1A 47F 16V LTC1153 * TA13 13 LTC1153 UO TYPICAL APPLICATI S Auto-Reset Circuit Breaker with Programmable (1-6) Number of Retries Using Binary Counter 5V TO 18 V + 100F ON/OFF 0.1 IN VS 5V 11 4 LOAD CT 16 VCC UP 74C193 CARRY QD ABCDGND 15 1 10 9 5 12 LTC1153 STATUS 100k 1N4148 DS 0.47F Z5U 100k 100k G IRF530 12V 7 GND SD + 0.22F 47F 8 14 FAULT INPUTS* LTC1153 * TA14 *SET WITH 3-BIT BINARY WORD = 7 - N DC Motor Driver with Stall-Current Circuit Breaking (Auto-Reset), Thermal Overload Shutdown and 10A Standby Current 12V + 470F ON/OFF 5V IN VS CT DS 0.1F 51k 10k 2N2907 100k G IRFZ34 120k MOTOR FAULT LED 0.02 LTC1153 0.33F STATUS 240 GND 12V SD *PTC THERMISTOR (100C) M 1N5400 *RL3006-50-100-25-PTO KEYSTONE MOUNT ON MOTOR CHASIS OR MOSFET HEAT SINK LTC1153 * TA15 14 OUTPUT LTC1153 U PACKAGE DESCRIPTIO N8 Package 8-Lead Plastic Lead 0.300 - 0.320 (7.620 - 8.128) 0.045 - 0.065 (1.143 - 1.651) 0.130 0.005 (3.302 0.127) 8 7 6 5 0.065 (1.651) TYP 0.009 - 0.015 (0.229 - 0.381) ( 0.400 (10.160) MAX +0.025 0.325 -0.015 +0.635 8.255 -0.381 0.250 0.010 (6.350 0.254) 0.045 0.015 (1.143 0.381) ) 0.100 0.010 (2.540 0.254) 0.125 (3.175) MIN 0.020 (0.508) MIN 1 2 3 4 0.018 0.003 (0.457 0.076) N8 0392 S8 Package 8-Lead Plastic SOIC 0.189 - 0.197 (4.801 - 5.004) 0.010 - 0.020 x 45 (0.254 - 0.508) 0- 8 TYP 7 6 5 0.004 - 0.010 (0.101 - 0.254) 0.008 - 0.010 (0.203 - 0.254) 0.016 - 0.050 0.406 - 1.270 8 0.053 - 0.069 (1.346 - 1.752) 0.014 - 0.019 (0.355 - 0.483) 0.050 (1.270) BSC 0.228 - 0.244 (5.791 - 6.197) 0.150 - 0.157 (3.810 - 3.988) 1 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of circuits as described herein will not infringe on existing patent rights. 2 3 4 SO8 0392 15 LTC1153 U.S. Area Sales Offices NORTHEAST REGION Linear Technology Corporation One Oxford Valley 2300 E. Lincoln Hwy.,Suite 306 Langhorne, PA 19047 Phone: (215) 757-8578 FAX: (215) 757-5631 CENTRAL REGION Linear Technology Corporation Chesapeake Square 229 Mitchell Court, Suite A-25 Addison, IL 60101 Phone: (708) 620-6910 FAX: (708) 620-6977 SOUTHEAST REGION Linear Technology Corporation 17060 Dallas Parkway Suite 208 Dallas, TX 75248 Phone: (214) 733-3071 FAX: (214) 380-5138 SOUTHWEST REGION Linear Technology Corporation 22141 Ventura Blvd. Suite 206 Woodland Hills, CA 91364 Phone: (818) 703-0835 FAX: (818) 703-0517 NORTHWEST REGION Linear Technology Corporation 782 Sycamore Dr. Milpitas, CA 95035 Phone: (408) 428-2050 FAX: (408) 432-6331 International Sales Offices FRANCE Linear Technology S.A.R.L. Immeuble "Le Quartz" 58 Chemin de la Justice 92290 Chatenay Mallabry France Phone: 33-1-46316161 FAX: 33-1-46314613 KOREA Linear Technology Korea Branch Namsong Building, #505 Itaewon-Dong 260-199 Yongsan-Ku, Seoul Korea Phone: 82-2-792-1617 FAX: 82-2-792-1619 TAIWAN Linear Technology Corporation Rm. 801, No. 46, Sec. 2 Chung Shan N. Rd. Taipei, Taiwan, R.O.C. Phone: 886-2-521-7575 FAX: 886-2-562-2285 GERMANY Linear Techonolgy GMBH Untere Hauptstr. 9 D-8057 Eching Germany Phone: 49-89-319741-0 FAX: 49-89-3194821 SINGAPORE Linear Technology Pte. Ltd. 101 Boon Keng Road #02-15 Kallang Ind. Estates Singapore 1233 Phone: 65-293-5322 FAX: 65-292-0398 UNITED KINGDOM Linear Technology (UK) Ltd. The Coliseum, Riverside Way Camberley, Surrey GU15 3YL United Kingdom Phone: 44-276-677676 FAX: 44-276-64851 JAPAN Linear Technology KK 5F YZ Building 4-4-12 Iidabashi Chiyoda-Ku Tokyo, 102 Japan Phone: 81-3-3237-7891 FAX: 81-3-3237-8010 World Headquarters Linear Technology Corporation 1630 McCarthy Blvd. Milpitas, CA 95035-7487 Phone: (408) 432-1900 FAX: (408) 434-0507 10/92 16 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 FAX: (408) 434-0507 TELEX: 499-3977 LT/GP 1092 10K REV 0 LINEAR TECHNOLOGY CORPORATION 1992