3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series * Military (with 3M's 3518 and N3518 polarizing key) and centerbump polarization * Optional ejector latches * Optional polarizing posts * Mounting holes for securing header to board * Dependable eye-of-the needle pin design * Optional high-temperature insulator * See the Regulatory Information Appendix (RIA) in the "RoHS compliance" section of www.3Mconnectors.com for compliance information Date Modified: May 22, 2012 TS-0478-C Sheet 1 of 4 Physical Insulation: Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT) Flammability: UL 94V-0 Color: Gray (PBT), Black (PCT) Contact: Material: Copper Alloy Plating: Underplating: 100 " [ 2.54 m ] Nickel Wiping Area: 30 " [ 0.76 m ] Gold Solder Tails: 100 " [ 2.54 m ] Tin Lead or 300u" [7.62 um] Matte Tin (See Ordering Information) Marking: 3M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: 1 A Insulation Resistance: >1 x 109 at 500 VDC Withstanding Voltage: 1,000 VRMS at Sea Level Environmental Temperature Rating: -55C to +105C UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series -620T02 Header with Short Ejector/Latch for 3M Sockets without Strain Relief -600T02 Header with No Ejector/Latch .08 [2.0] -630T02 Header with Long Ejector/Latch for 3M sockets with Strain Relief .08 [2.0] .573 .010 [14.55] .424 .010 [10.77] 1.07 Ref [27.2] .68 [17.3] .97 Ref [24.6] A .37 Ref [9.4] .46 Ref [11.7] D .100 2.54 .020 0.51 .28 7.1 REF. .185 4.70 .25 6.4 .34 8.6 .13 3.2 .100 2.54 2X O .100 [2.54] SEE NOTE #2 REF. POSITION #1 B A Notch B (See Table) .025 .002 Sq Typ [0.64] Position 1 Orientation Triangle Notch C (See Table & Note 1) Notch A (See Table & Note 1) A .24 [6.1] .68 [17.3] .30 [7.6] .35 [8.9] .175 .010 [4.44] Section A-A .19 [4.8] .020 [0.51] A .21 [5.3] .16 [4.1] Inch (mm) C Tolerance Unless Noted Notes: 1. Notches A & C will accomodate 3M Polarizing Keys 3518 or N3518. 2. Accepts Rear and Front entry mounting hardware: Rear Entry: #4-24 thread cutting screw 3M Part # 3341-5 (.116 [2.95] dia. mounting hole). Front Entry (Prior to installation of latch): #2-56 Bolt and Nut 3M Part # 3341-6 (.106 [2.69] dia. mounting hole). See illustrations on page 4 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com .0 Inch .1 .00 .000 .01 .005 [ ] Dimensions for Reference only C TS-0478-B Sheet 2 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin Pin Qty 3000 Series Dimensions 3M Part Number A B C D Polarizing Notches Provided Insertion platen 3442-00XX 10 3793 1.26 (32.1) 1.105 (28.07) 0.865 (21.97) 0.71 (18.0) BC 3442-0048 14 3314 1.46 (37.2) 1.305 (33.15) 1.065 (27.05) 0.91 (23.1) BC 3442-0049 16 3408 1.56 (39.7) 1.405 (35.69) 1.165 (29.59) 1.01 (25.6) ABC 3442-0050 20 3428 1.76 (44.8) 1.605 (40.77) 1.365 (34.67) 1.21 (30.7) ABC 3442-0051 24 3627 1.96 (49.9) 1.805 (45.85) 1.565 (39.75) 1.41 (35.8) ABC 3442-0052 26 3429 2.06 (52.4) 1.905 (48.39) 1.665 (42.29) 1.51 (38.3) ABC 3442-0053 30 3440 2.26 (57.5) 2.105 (53.47) 1.865 (47.37) 1.71 (43.4) ABC 3442-0054 34 3431 2.46 (62.6) 2.305 (58.55) 2.065 (52.45) 1.91 (48.5) ABC 3442-0055 40 3432 2.76 (70.2) 2.605 (66.17) 2.365 (60.07) 2.21 (56.1) ABC 3442-0056 50 3433 3.26 (82.9) 3.105 (78.87) 2.865 (72.77) 2.71 (68.8) ABC 3442-0057 60 3372 3.76 (95.6) 3.605 (91.57) 3.365 (85.47) 3.21 (81.5) ABC 3442-0058 64 3764 3.96 (100.7) 3.805 (96.65) 3.565 (90.55) 3.41 (86.6) ABC 3442-0059 .300 Min [7.62] Side to Side Stackability .106 [2.69] or (See Note 2) .116 [2.95] See Note 3 .060 [1.52] Position 1 .100 .003 [2.54] R S T R S T Tail Section .100 .003 [2.54] Compliant Section 4X R .009 Max [0.23] 4X .002 .001 [0.05] Break Edges .352 [8.94] B Mating Area Section R-R R .020 Sym [0.51] Section T-T Recommended Mounting Hole Pattern Section S-S Note: 3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M's compliant pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal force is not less than 10 pounds per pin. 4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX) styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally equivalent to -2 & -3 roll pin latches) Pin Cross Sections Hole Size for: Preferred Drilled - o.0453 .0005 Acceptable Drilled - o.0453 +.0005 -.0010 After Etchback - o.0460 Max After Plating - .o040 .003 Board thickness - .093 to .150 Plating: .001 Minimum Copper plating thickness .0003 Min Tin plating If ordering Snap-In style latches separately, please use the chart below Short Latch Long Latch Color High Temp (PPA) 3505-30 3505-31 Gray High Temp (PPA) N3505-30B N3505-31B Black Ordering Information X XXXX - 6X0T02XX Prefix: Blank = Std.Temp Gray (PBT): (TC Plating Req'd) N = High Temp Black (PCT) (RB Plating Req'd) Plating suffix: TC = 30 " Gold w/Tin-Lead Tails (App. E2 & C2 Apply) RB = 30 " Gold w/Matte Tin Tails (App. E1 & C1 Apply) 3M Part Number Assembly Equipment: Use 3442-00XX platen (see chart above) and appropriate commercial arbor press to press header into pc board. 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com Latch/Ejector System: 0 = No latch/ejectors 2 = Short latch/ejectors 3 = Long latch/ejectors 5 = Short, Snap-In Latch/Ejectors 6 = Long, Snap-In Latch/Ejectors TS-0478-B Sheet 3 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 TM TM Four-Wall Header 3M 3M Three-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series 3000 Series .100" x .100" Latch/Ejector, Straight and Right Angle Polarizing Post .321 [8.15] 3 2 0 1 -3 3 2 0 1 -4 PBT LCP G ra y B la c k .100 Dia [2.54] Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude .115" [2.92] Polarizing Keys Dim A N3518 LCP Blac k .02 3518 PBT Gray .02 Breakaway Tab .09 [2.3] .34 Ref [8.6] A .15 [3.8] Note: #2216 B/A Scotchweld can be used to adhere keys. Mounting Hardware 3341-5 (Installed from bottom of board) 3341-6 (Must be inserted prior to latch on vertical headers) .50 [12.7] .31 [7.9] Panhead Thread Cutting Screw: #4-24 X 5/16" Type: USA Std BT, Federal BG Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2" 3341-5 & 6 Material - Stainless Steel Not for use with Condo headers. TS-0478-B TS-0771-E Sheet 4 of 4 Sheet 5 of 5 3 3 Electronic Solutions Division Electronic Solutions Division Interconnect Solutions Interconnect Solutions http://www.3Mconnectors.com http://www.3Mconnector.com 3M is a trademark of 3M Company. 3Msales is a trademark 3M Company. For technical, or orderingofinformation call For technical, sales or ordering information call 800-225-5373 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnectors.com Please recycle. Printed in USA. (c) 3M 2012. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company.