‧2/3/8 stage charging (Note 4)
‧Universal AC input / Full range
‧Built-in active PFC function PF>0.95
‧Protection: Reverse polarity / Short circuit / Over voltage / Over temperature
‧Charger for lead-acid batteries
‧3 color LED loading indicator
‧Built-in remote ON-OFF control
‧Built-in temperature compensation function
‧(depends on charging current)Built-in fan speed control
‧3 years warranty
■ Features :
SPECIFICATION
PB-600-12 PB-600-24 PB-600-48
MODEL
BOOST CHARGE VOLTAGE
FLOAT CHARGE VOLTAGE
OUTPUT CURRENT
BATTERY TYPE
RECOMMENDED BATTERY
CAPACITY(AMP HOURS)
(Note 3)
OUTPUT
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
ENVIRONMENT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
SAFETY &
EMC
(Note 2)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
OVER VOLTAGE
PROTECTION
AC CURRENT (Typ.)
14.4V 28.8V 57.6V
13.8V
40A
Open & Sealed Lead Acid
135 ~ 400AH
27.6V 55.2V
21A 10.5A
70 ~ 210AH 35 ~ 105AH
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
86% 87% 89%
6.8A/115VAC 3.4A/230VAC
25A/115VAC 50A/230VAC
<3.5mA / 240VAC
16 ~ 18V 32 ~ 35V 64.5 ~ 69.5V
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL1012, TUV EN60335-1, EN60335-2-29 (except for 48V), EN60950-1(48V only) approved
Compliance to EN55022 class B (CISPR22), EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024; light industry level, criteria A
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
-20 ~ +60 (Refer to "Derating Curve")℃
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH ℃
± ℃ ℃0.05%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
MTBF 135.6K hrs min. MIL-HDBK-217F (25 )℃
230*158*67mm(L*W*H)
DIMENSIONOTHERS
NOTE
PACKING 2.2Kg; 6pcs/14.2Kg/1.76CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
3. This is Mean Well's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.
4. Please choose the "3 stage" selection when the charger is used to charge the batteries and power the loads in the same time.
PB-600 series
600W Single Output Battery Charger
FUNCTION
REMOTE CONTROL
LEAKAGE CURRENT FROM BATTERY (Typ.)
FAST CHARGE
OUTPUT OK
CHARGER OK
TEMPERATURE SENSE
Open: Normal work Short: Stop Charging
1mA
2 / 3 / 8 stage selectable
Relay contact (RY13)
Relay contact (RY15)
By NTC
File Name:PB-600-SPEC 2014-09-15
POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load
EMC IMMUNITY
EMC EMISSION
Mechanical Specification Case No.805C Unit:mm
Charging Curve
Charge Current Charge Current
Constant Current Constant Current
stage 1 stage 1stage 2 stage 2 stage 3
Constant Voltage Constant Voltage Float
Start Start
2 Stage 3 Stage
Charge Voltage Charge Voltage
100% 100%
10% 10%
boost boost
float
V V
V
Orange OrangeGreen Green
Color of LED Color of LED
PB-600 series
600W Single Output Battery Charger
File Name:PB-600-SPEC 2014-09-15
Pin No. Pin No.
5,6
7
9
10
3,4
RY13 : Battery bank OK NTC / GND : Temperature sense
RY15 : Charger OK RC+ / RC-: Remote ON/OFF
1,2 8
Assignment Assignment
RY15
GND
NC
RY13
Mating Housing Terminal
or equivalent or equivalent
Control Pin No. Assignment(CN100) : HRS DF11-10DP-2DS or equivalent
HRS DF11-10DS
HRS DF11-**SC
RC-
RC+
NTC(5K )Ω
Air flow
direction
INLET
SWITCH
ON/OFF
42.5145
7
230
48
67
24.1
Derating Curve Static Characteristics
INPUT VOLTAGE (VAC) 60Hz
90 95 100 115 264
90
100
80
70
60
50
40
AMBIENT TEMPERATURE ( )℃
20
40
60
80
100
-20 0 10 20 30 40 50 60 70 (HORIZONTAL)
PB-600 series
600W Single Output Battery Charger
File Name:PB-600-SPEC 2014-09-15
Block Diagram
CONTROL
CONTROL
DETECTION
DETECTION
SWITCHING
POWER
ACTIVE
INRUSH
CURRENT
LIMITING
RECTIFIER
&
PFC
PFC
CONTROL
AUX
POWER
MCU
FAN
OTP
PWM
REMOTE
Bank OK
Charger OK
REVERSE
CURRENT
FILTER
&
RECTIFIER
+V
2/8
STAGE
SELECT
RC
RY13
RY15
I/P FILTER
EMI
PFC : 95KHz
PWM fosc : 60KHz
Charge Current
stage 1 stage 2 stage 3 stage 4 stage 5 stage 6 stage 7 stage 8
Charge Voltage
8 Stage
Pulse Soft Start Constant Current Constant Voltage Analysis Recond Float Maintain
Orange Green
Color of LED
Between RC+(pin10) and RC-(pin9)
SW Open
SW Short
Charging
ON
OFF
The charger can be turned ON/OFF by using the
"Remote Control" function.
SW
PB-600 series
600W Single Output Battery Charger
File Name:PB-600-SPEC 2014-09-15
Power
Power
Power
Stage 8/3/2
Stage 8/3/2
Stage 8/3/2
10
10
10
910
CN100
RY13
NC
RY15
GND
RC-
RY13
NC
RY15
RTH
RC+
12
Status
Color
Red
Orange
Green
Steady
Fail
Full Charging
Charging
Flashing
Function Manual
1.Remote Control
+
+
+
Battery
Battery
Battery
-
-
-
Switch
Right
Middle
Left
Charging mode
2 stage charging
3 stage charging
8 stage charging
(1)The charger features user selectable 2,3, or 8 stage charging.
(2)Please choose the "3 stage" selection when the charger
The charging profile is selected by moving the slide switch
is used to charge the batteries and power the loads in the
same time.
on the back panel.
2. 2,3, or 8 stage charging select
Charger
Work normally
Between pin5 and pin6(RY15)
ON (Short)
OFF (Open)
3.Charger OK Relay(RY15)
9
9
10
10
CN100
CN100
RY13
RY13
NC
NC
RY15
RY15
GND
GND
RC-
RC-
RY13
RY13
NC
NC
RY15
RY15
RY15
RTH
RTH
RC+
RC+
1
1
2
2
Failure or protection function
activated
Function Description of CN100 The Function of LEDs
Pin No. Function Description
1,2
5,6
7,8
9,10
RY13 Relay contact rating(max.) : 30V/1A resistive. ; "Short" when the battery is full,
Relay contact rating(max.) : 30V/1A resistive. ; "Short" when the unit is working normally;
Temperature sensor comes along with the charger can be connected to the unit to allow
Turn the output on and off by electrical or dry contact between pin 10 (RC+) and pin 9(RC-)
"Open" when the battery is still charging
"Open" when the unit is in a faulty condition
temperature compensation of the charging voltage
Open : Normal work , Short : Stop charging
RY15
GND / RTH
RC- / RC+
Bank
1.Bank OK (RY13)
Between pin1 and pin2(RY13) Color of LED
ON (Short) Green
OFF (Open) Orange
4.Output OK (RY13)
910
CN100
RY13
NC
RY15
GND
RC-
RY13
NC
RY13
RY15
RTH
RC+
12
PB-600 series
600W Single Output Battery Charger
File Name:PB-600-SPEC 2014-09-15
Power
10
Power
10
+
Battery
-
+
Battery
-
Temperature sensor comes along with the charger can
5.Temperature compensation
be connected to the unit to allow temperature compensation
of the charging voltage.
If the sensor is not used, the charger still works normally.
CN100
NTC
RY13
NC
RY15
GND
RC-
RY13
NC
RY15
RTH
RC+
12
910
Battery Full
Charging
The temperature sensor can either be attached to
the battery or placed in its surrounding environment.
Stage 8/3/2
Stage 8/3/2
