8 | 7 6 5 4 | 3 2 { - THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION -,- : Loc DIST REVISIONS COPYRIGHT BY TYCO ELECTRONICS CORPORATION. ALL RIGHTS RESERVED. CM OO P LTR DESCRIPTION DATE DWN APVD AF | REVISED PER ECO08-017241 15JULO8 |IHMR| DB AF 1| REVISED PER ECO09-023313 130cTo9 | KK |AEG 91.52+9-29 oe 3.96 0.00 / POST TO WITHSTAND 13 NEWTONS (3 LBS) MINIMUM AXIAL FORCE EDGE OF BOARD [.156] | 2.060% 858 | IN BOTH DIRECTIONS SHOWN WITHOUT DISLODGING. NP $160.25 [.010]W / TOLERANCES APPLY TO SOLDER SIDE OF BOARD. TYP | /d MEASURED AT SURFACE |A J PLASTIC FLASH PERMITTED IN THIS AREA. D Ay D /\ PARTS COMPLY WITH AMP SOLDERABILITY SPEC. NO. 109-112. | A aN aN aN a aN Ld ONE HOLE MAY BE UNDERSIZED 1.65/1.52 [.065/.060] DIA. FOR ASSEMBLY RETENTION DURING WAVE SOLDERING. _- an a YF REF JX MATERIAL: HEADERTHERMOPLASTIC POLYESTER GLASSFILLED 94V0 (NATURAL) POSTCOPPER ALLOY (SEE NOTES 13 & 14 FOR PLATING) ( 6 RECOMMENDED MOUNTING HOLE PATTERN /X COORDINATE DIMENSION APPLIES FROM CENTER OF ACTUAL FEATURE. | FOR 1.60 [.063] THICK P.C. BOARD - | >{_4 /d PLASTIC BURRS CAUSED BY CUTOFF TOOLING ARE PERMITTED WITHIN THE MAXIMUM TOLERANCE ENVELOPE. 1 VAN POST TO BE MEASURED WHEN STRIP IS HELD FLAT. . (L) _ AX POST MUST WITHSTAND TWO 90 BENDS AGAINST EXTRUSION WITHOUT BREAKING. 7.62+0.38 [.300+.015] _ Dd DIMENSION SHOULD BE 4.45 [.175] MIN WHEN MATING WITH A MTA156 0.5575. 40 010/100) CONNECTOR ASSEMBLY OR A SL156 CONNECTOR ASSEMBLY. AX PLATING: GOLD PLATE AREA, 0.00038 [.000015] MINIMUM, ALL SIDES, OVER NICKEL UNDERPLATE, 0.00127 [.000050] MINIMUM, ALL SIDES AND ENTIRE LENGTH OF POST. AN PLATING: BRIGHT TIN/LEAD (93/7) PLATE AREA, 0.003810.00889 [.000150.000350] THICK, ALL 0.25 [.010] FOUR SIDES 3.18 [.125] MINIMUM FOR 2 THRU 24. 1. 1440.03 [_J0..38 [.015]JA MATTE TIN PLATE AREA 0.003810.00889 [.000150.000350] _ [.045+.001]~ "| [7 ej} ALL POSTS THICK ALL FOUR SIDES, 3.18 [.125] FOR 32 THRU 54. pe /\Ad, [6160.20 1.008]@ Ad, OBSOLETE PARTS: OBSOLETE CIS STREAMLINING PER D.RENAUD/D.SINIS| | [0.38 [.015]}A 1.85+0.25 / 7 | (~ [.073+.010] POST NO. 1 ' 95.10 [3.744] 24 5641120-4 95.10 [3.744] 24 26444204+ AB \ \ \ \ \ \ iN i\ LA [IN : 91.14 [3.588] 25 5-6411203 91.14 [3.588] 23 P64442563- Ao 559 i 87.17 [3.432] 22 56411202 87.17 [3.432] 22. | 26444202 fs (10.16) F365] 576 83.21 [3.276] 21 56411201 83.21 [3.276] 21. |2-644420-4+ fh C400] MIN TYP F030] 79.25 [3.120] 20 56411200 79.25 [3.120] 20 |2-644420-0 Pf) 16.51+0.38 fo \ | MAX 75.29 [2.964] 19 4641120-9 75.29 [2.964] 19 }-64H4203- 8 B [.650+.015] | : 4 71.32 [2.808] 18 4641120-8 71.32 [2.808] 18 |1-641120-8 B A | LS 67.36 [2.652] | 7 4641120/7 67.36 [2.652] 17 +64+44204 Aa ' \ ! 63.40 [2.496] 16 4641120-6 a 63.40 [2.496] 16 +6441420-6- Aa | [ 4 59.44 [2.340] 15 4641120-5 <U 59.44 [2.340] 15 1- 6444265 A { J ~ 55.47 [2.184] 14 4641120-4 LL 55.47 [2.184] 14 164-11204 Aa i 3.1840.25 | LL 51.51 [2.028] 13 4641120S3 51.51 [2.028] 13 1 64 17203 A /\ [.1254.010] a 47.55 [1.872] 12 4641120-2 2 47.55 [1.872] 12 1-641120-2 ]0.25/25.40[.010/1.000] 10.8040.25 | <t 43.59 [1.716] 11 4641120-1 = 43.59 [1.716] 11 +644+4+264 Aa . [-4254.010] a 39.62 [1.560] 10 46411200 39.62 [1.560] 10 |16411200 _ = 5.1820.38 35.66 [1.404] 9 36411209 S 35.66 [1.404] 9 6411209 - [.156] = _ 784.012] TYP 31.70 [1.248] 8 3641120-8 0) 31.70 [1.248] 8 641120-8 TYP Vp 27.74 [1.092] 7 3641120-7 27.74 [1.092] 7 6411207 23.77 |.936| 6 5641120-6 23.77 |[.936| 6 641120-6 19.81 [.780] 5 5641120-5 19.81 [.780] 5 6411205 15.85 [.624] 4 5641120-4 15.85 [.624] 4 641120-4 11.89 [.468] 5 56411203 11.89 [.468] 5 6411203 7.92 [.312] 2 3641120-2 7.92 [.312] 2 6411202 NO.OF NO.OF A DIM (L) [NOOF ASSEMBLY DIM (L) | NOS) ASSEMBLY | THIS DRAWING IS A CONTROLLED DOCUMENT. |S Logyer O7NOVO2 Zz, Tyco Electronics Corporation DIMENSIONS: TOLERANCES UNLESS 0. BOSS! a Electronics van eaees mm [INCHES] ee "0. BOSS! ee MTA.156 HEADER ASSEMBLY, FRICTION r 1 ( orc f- Propect Sees LOCK, STRAIGHT, .045 ROUND POST, ME RI Of PLC O19 L008] APPLICATION SPEC 000015 GOLD MATERIAL VS FINISH IN - WEIGHT _ A1 00779 C=641 120 _ CUSTOMER DRAWING SA 517 Tg ary AMP 4805 REV 31MAR2000