Miniature Single-Sided Thick Film Chip Resistors The ims IMS series of miniature single-sided thick film chip resistors is ideally suited for hybrid and printed circuit applications. Many combinations of termination materials are available to meet the requirements of all common attachment methods. Sizes from .025" X .030" to 0.150" X 0.050" are offered. A wide range of values and tolerances is available. Terminations Single side termination -1 -3 -C Au PtAg PtAg with 62/36/2 solder coating Note: Not all termination materials available in all styles. Resistance Ranges Thick film technology Single-Sided Terminations for Wirebonding, Soldering, and Epoxy Attachment Gold, Platinum Silver, and Platinum Silver with Solder Coating Terminations Resistance values from to 1000 G 0.1 Tolerances to 1 % Low TCRs 50 Schoolhouse Lane Portsmouth, RI 02871 Tel (401) 683-9700 Fax (401) 683-5571 e-mail: ims@ims-resistors.com http://www.ims-resistors.com 017 014 010 H09 009 008 005 004 003 002 001 0001 Features The table below illustrates the resistance values and the tolerances available for all of IMS' single side devices. Resistance values can be as low as and as high as 1000 G (device dependent). For resistances higher 0.1 than 1000 G, consult the factory. 0.1 - 0.99 5% 10% 20% 1.0 - 9.9 2% 5% 10% 20% 10 - 25M 1% 2% 5% 10% 20% 26M - 1G 5% 10% 20% 30% 40% 50% 1.1G - 9.9G 20% 30% 40% 50% 10G - 99G 30% 40% 50% 100G - 1T 40% 50% Jumpers are available in all sizes. 1 Larger bond pads available for auto wirebonding. Dimensions Part Number IMS000 IMS001 IMS002 IMS003 IMS004 IMS005 IMS008 IMS009 IMSH09 IMS010 IMS014 IMS017 Length 0.045 .005 0.050 .005 0.075 .005 0.100 .005 0.150 .005 0.100 .005 0.100 .005 0.080 .005 0.080 .005 0.125 .005 0.035 .005 0.025 .005 Width Height 0.030 .005 0.050 .005 0.050 .005 0.050 .005 0.050 .005 0.100 .005 0.025 .005 0.050 .005 0.050 .005 0.050 .005 0.035 .005 0.030 .005 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. 0.016 max. WVDC Tolerances (%) 60 60 100 160 350 160 175 150 150 230 50 40 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 10, 20, 30 1, 2, 5, 10 1, 2, 5, 10 1, 2, 5, 10 W W H H LL T Specifications Part number IMS000 IMS001 IMS002 IMS003 IMS004 IMS005 IMS008 IMS009 IMSH09 IMS010 IMS014 IMS017 Rated power (70oC)* 125 mW 125 mW 175 mW 250 mW 350 mW 500 mW 100 mW 175 mW 175 mW 250 mW 125 mW 30 mW * Increased power handling can be achieved by using proper circuit design and power management techniques . Ordering Information Samples Available From Stock Example: 0.045" X 0.030," gold terminations, 100 , 5% tolerance IMS000 - 1 - 1000 J 0001 003 008 010 1 2 001 004 H09 0142 002 005 009 0172 Available in -0, -1, -2 only Available in -1 only Termination -0 -2 -1 -3 -C Tolerance F - 1% G - 2% J - 5% K - 10% L - 15% M - 20% N - 30% Resistance value Pd/Ag (IMS000 only) Pd/Ag w/ 62/36/2 solder (IMS000 only) The first three digits are significant values. The fourth is the number of Au zeroes following. The R indicates a Pt/Ag Pt/Ag w/ 62/36/2 solder decimal point when resistance value is Add "B" after the dash number to indicated a backplane of the same Metalization (-1,-3 only). less than 100. Bulk packaging is standard. Tape and reel and waffle packs are available for some sizes. Please consult the factory. IMS ver.6 03/04 Specifications subject to change without notice. 50 Schoolhouse Lane Portsmouth, RI 02871 Tel (401) 683-9700 Fax (401) 683-5571 e-mail: ims@ims-resistors.com http://www.ims-resistors.com