R71VN4220AA3J - KEMET Electronics Corporation

09/2008 74

Loose Taped

Fig.1 Fig.2

Ø d ±0.05 p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5

0.6 or 0.8* 0.8 1

*See size table.

All dimensions are in mm.

MKP Series

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm.

Plates: metal layer deposited by evaporation under

vacuum.

Winding: non-inductive type.

Leads: tinned wire.

Protection: plastic case, thermosetting resin lled.

Box material is solvent resistant and ame

retardant according to UL94 V0.

Marking: Manufacturer’s logo, series, capacitance,

tolerance, D.C. rated voltage.

Operating temperature range: -40 to +110°C

For temperatures between +105°C and 110°C a

decreasing factor of 4% per degree C on the rated

voltage VR has to be applied.

ELECTRICAL CHARACTERISTICS

Capacitance range: 0.01µF to 22µF

Capacitance tolerances (measured at 1 kHz):

±5% (J) ±10% (K); ±20% (M);

Tolerance available upon requests

Total self-inductance (L): (lead length ~2mm)

Pitch (mm) 10 15 22.5 27.5 37.5

L(nH) ≈9 10 18 18 20

Dissipation factor (DF):

tgδx10-4 at +25°C ±5°C: ≤10 (6)* at 1kHz *

Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C

Voltage charge time: 1 min

Voltage charge: 100 Vdc

Performance

≥1 x 105 MΩ for C ≤0.33µF (5 x 105 MΩ)*

≥30000 s for C >0.33µF (150000 s)*

*Typical value

Test voltage between terminations:

1.6xVR applied for 2 s at +25°C±5°C

R71

MKP Series

METALLIZED POLYPROPYLENE FILM

CAPACITOR

Typical applications: P.F.C. (Power Factor Correction)

PRODUCT CODE: R71

Pitch Box thickness (B) Maximum dimensions (mm)

(mm) (mm) B max H max L max

10.0 All B +0.2 H +0.1 L +0.2

15.0 <7.5 B +0.2 H +0.1 L +0.3

15.0 ≥7.5 B +0.2 H +0.1 L +0.5

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C±2°C

Relative humidity (RH): 93% ±2%

Test duration: 56 days

Test conditions 2nd

Temperature: +60°C±2°C

Relative humidity (RH): 95% ±2%

Test duration: 500 hours

Performance

Capacitance change |∆C/C|: ≤5%

Insulation resistance: ≥50% of initial limit.

Endurance:

Test conditions

Temperature: +105°C±2°C

Test duration: 2000 h

Voltage applied: 1.25xVR

Performance

Capacitance change |∆C/C|: ≤5%

Insulation resistance: ≥50% of initial limit.

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C±5°C

Dipping time (with heat screen): 10 s±1 s

Performance

Capacitance change |∆C/C|: ≤2%

Winding scheme

09/2008

Rated

Cap.

420Vdc/220Vac

Std dimensions

Ø d

(mm)

Max

dv/dt

(V/µs)

Max K0

(V2/µs) Part Number

B H L p

0.010 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2100--0--

0.015 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2150--0--

0.022 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2220--0--

0.033 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2330--0--

0.047 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2470--0--

0.068 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 2680--3--

0.10 µF 4.0 9.0 13.0 10.0 0.6 250 210 E3 R71MF 3100--3--

0.15 µF 5.0 11.0 13.0 10.0 0.6 250 210 E3 R71MF 3150--3--

0.22 µF 6.0 12.0 13.0 10.0 0.6 250 210 E3 R71MF 3220--3--

0.10 µF 5.0 11.0 18.0 15.0 0.6 160 134 E3 R71MI 3100--0--

0.15 µF 5.0 11.0 18.0 15.0 0.6 160 134 E3 R71MI 3150--0--

0.22 µF 5.0 11.0 18.0 15.0 0.6 160 134 E3 R71MI 3220--0--

0.33 µF 6.0 12.0 18.0 15.0 0.6 160 134 E3 R71MI 3330--0--

0.47 µF 7.5 13.5 18.0 15.0 0.6 160 134 E3 R71MI 3470--0--

0.47 µF 6.0 17.5 18.0 15.0 0.6 160 134 E3 R71MI 3470--1--

0.47 µF 9.0 12.5 18.0 15.0 0.6 160 134 E3 R71MI 3470--2--

0.68 µF 6.0 17.5 18.0 15.0 0.6 160 134 E3 R71MI 3680--4--

0.68 µF 8.5 14.5 18.0 15.0 0.6 160 134 E3 R71MI 3680--3--

0.68 µF 13.0 12.0 18.0 15.0 0.8 160 134 E3 R71MI 3680--2--

1.0 µF 7.5 18.5 18.0 15.0 0.8 160 134 E3 R71MI 4100--4-M

1.0 µF 10.0 16.0 18.0 15.0 0.8 160 134 E3 R71MI 4100--3--

1.5 µF 11.0 19.0 18.0 15.0 0.8 160 134 E3 R71MI 4150--3-

0.22 µF 6.0 15.0 26.5 22.5 0.8 100 84 E3 R71MN 3220--0--

0.33 µF 6.0 15.0 26.5 22.5 0.8 100 84 E3 R71MN 3330--0--

0.47 µF 6.0 15.0 26.5 22.5 0.8 100 84 E3 R71MN 3470--0--

0.68 µF 6.0 15.0 26.5 22.5 0.8 100 84 E3 R71MN 3680--0--

1.0 µF 7.0 16.0 26.5 22.5 0.8 100 84 E3 R71MN 4100--3--

1.5 µF 8.5. 17.0 26.5 22.5 0.8 100 84 E3 R71MN 4150--3-M

1.5 µF 10.0 18.5 26.5 22.5 0.8 100 84 E3 R71MN 4150--0--

2.2 µF 10.0 18.5 26.5 22.5 0.8 100 84 E3 R71MN 4220--4-M

2.2 µF 11.0 20.0 26.5 22.5 0.8 100 84 E3 R71MN 4220--3--

3.3 µF 13.0 22.0 26.5 22.5 0.8 100 84 E3 R71MN 4330--3--

0.68 µF 9.0 17.0 32.0 27.5 0.8 80 67 E3 R71MR 3680--0--

1.0 µF 9.0 17.0 32.0 27.5 0.8 80 67 E3 R71MR 4100--0--

1.5 µF 11.0 20.0 32.0 27.5 0.8 80 67 E3 R71MR 4150--0--

2.2 µF 13.0 22.0 32.0 27.5 0.8 80 67 E3 R71MR 4220--0--

3.3 µF 14.0 28.0 32.0 27.5 0.8 80 67 E3 R71MR 4330--3--

4.7 µF 18.0 33.0 32.0 27.5 0.8 80 67 E3 R71MR 4470--0--

6.8 µF 22.0 37.0 32.0 27.5 0.8 80 67 E3 R71MR 4680--0--

3.3 µF 11.0 22.0 41.5 37.5 1.0 60 50 E3 R71MW 4330--0--

4.7 µF 16.0 28.5 41.5 37.5 1.0 60 50 E3 R71MW 4470--0--

6.8 µF 19.0 32.0 41.5 37.5 1.0 60 50 E3 R71MW 4680--0--

10.0 µF 20.0 40.0 41.5 37.5 1.0 60 50 E3 R71MW 5100--0--

15.0 µF 24.0 44.0 41.5 37.5 1.0 60 50 E3 R71MW 5150--0--

22.0 µF 30.0 45.0 41.5 37.5 1.0 60 50 E3 R71MW 5220--0--

R71

MKP Series

METALLIZED POLYPROPYLENE FILM

CAPACITOR

PRODUCT CODE: R71

Rated

Cap.

520Vdc/250Vac*

Std dimensions

Ø d

(mm)

Max

dv/dt

(V/µs)

Max K0

(V2/µs) Part Number

B H L p

0.010 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2100--0--

0.015 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2150--0--

0.022 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2220--0--

0.033 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2330--0--

0.047 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2470--3--

0.068 µF 4.0 9.0 13.0 10.0 0.6 300 312 E3 R71VF 2680--3--

0.10 µF 5.0 11.0 13.0 10.0 0.6 300 312 E3 R71VF 3100--3--

0.15 µF 6.0 12.0 13.0 10.0 0.6 300 312 E3 R71VF 3150--3--

0.10 µF 5.0 11.0 18.0 15.0 0.6 200 208 E3 R71VI 3100--0--

0.15 µF 5.0 11.0 18.0 15.0 0.6 200 208 E3 R71VI 3150--3--

0.22 µF 6.0 12.0 18.0 15.0 0.6 200 208 E3 R71VI 3220--3--

0.22 µF 6.0 17.5 18.0 15.0 0.6 200 208 E3 R71VI 3220--1--

0.33 µF 6.0 17.5 18.0 15.0 0.6 200 208 E3 R71VI 3330--4--

0.33 µF 7.5 13.5 18.0 15.0 0.6 200 208 E3 R71VI 3330--3--

0.33 µF 9.0 12.5 18.0 15.0 0.6 200 208 E3 R71VI 3330--2--

0.47 µF 8.5 14.5 18.0 15.0 0.6 200 208 E3 R71VI 3470--3--

0.47 µF 7.5 18.5 18.0 15.0 0.8 200 208 E3 R71VI 3470--1--

0.47 µF 13.0 12.0 18.0 15.0 0.8 200 208 E3 R71VI 3470--2--

0.68 µF 10.0 16.0 18.0 15.0 0.8 200 208 E3 R71VI 3680--3--

1.0 µF 11.0 19.0 18.0 15.0 0.8 200 208 E3 R71VI 4100--3-M

0.22 µF 6.0 15.0 26.5 22.5 0.8 120 125 E3 R71VN 3220--0--

0.33 µF 6.0 15.0 26.5 22.5 0.8 120 125 E3 R71VN 3330--0--

0.47 µF 6.0 15.0 26.5 22.5 0.8 120 125 E3 R71VN 3470--3--

0.68 µF 7.0 16.0 26.5 22.5 0.8 120 125 E3 R71VN 3680--3--

1.0 µF 10.0 18.5 26.5 22.5 0.8 120 125 E3 R71VN 4100--3--

1.5 µF 11.0 20.0 26.5 22.5 0.8 120 125 E3 R71VN 4150--3--

2.2 µF 13.0 22.0 26.5 22.5 0.8 120 125 E3 R71VN 4220--3--

0.68 µF 9.0 17.0 32.0 27.5 0.8 100 104 E3 R71VR 3680--0--

1.0 µF 9.0 17.0 32.0 27.5 0.8 100 104 E3 R71VR 4100--3--

1.0 µF 11.0 20.0 32.0 27.5 0.8 100 104 E3 R71VR 4100--0--

1.5 µF 11.0 20.0 32.0 27.5 0.8 100 104 E3 R71VR 4150--0--

2.2 µF 13.0 25.0 32.0 27.5 0.8 100 104 E3 R71VR 4220--3--

2.2 µF 14.0 28.0 32.0 27.5 0.8 100 104 E3 R71VR 4220--0--

3.3 µF 14.0 28.0 32.0 27.5 0.8 100 104 E3 R71VR 4330--3--

3.3 µF 18.0 33.0 32.0 27.5 0.8 100 104 E3 R71VR 4330--0--

4.7 µF 18.0 33.0 32.0 27.5 0.8 100 104 E3 R71VR 4470--3--

4.7 µF 22.0 37.0 32.0 27.5 0.8 100 104 E3 R71VR 4470--0--

6.8 µF 22.0 37.0 32.0 27.5 0.8 100 104 E3 R71VR 4680--3--

2.2 µF 11.0 22.0 41.5 37.5 1.0 70 73 E3 R71VW 4220--0--

3.3 µF 13.0 24.0 41.5 37.5 1.0 70 73 E3 R71VW 4330--3--

3.3 µF 16.0 28.5 41.5 37.5 1.0 70 73 E3 R71VW 4330--0--

4.7 µF 16.0 28.5 41.5 37.5 1.0 70 73 E3 R71VW 4470--0--

6.8 µF 19.0 32.0 41.5 37.5 1.0 70 73 E3 R71VW 4680--3--

6.8 µF 20.0 40.0 41.5 37.5 1.0 70 73 E3 R71VW 4680--0--

10.0 µF 20.0 40.0 41.5 37.5 1.0 70 73 E3 R71VW 5100--3--

10.0 µF 24.0 44.0 41.5 37.5 1.0 70 73 E3 R71VW 5100--0--

15.0 µF 24.0 44.0 41.5 37.5 1.0 70 73 E3 R71VW 5150--3--

15.0 µF 30.0 45.0 41.5 37.5 1.0 70 73 E3 R71VW 5150--0--

22.0 µF 30.0 45.0 41.5 37.5 1.0 70 73 E3 R71VW 5220--0--

All dimensions are in mm.

Note: If the working voltage (V) is lower than the rated voltage

(VR), the capacitors may work at higher dv/dt. In this case

the maximum value allowed is obtained multiplyng the above

value (see table dv/dt) with the ratio VR/V.

The pulse characteristics K0 depends on the voltage wave-

form and in any case it cannot overcome the value given in

the above table.

* Not suitable for across-the-line applications. Please refer to

Interference Suppression Capacitors at page 145.

Table 1

Standard

packaging style

Lead

length

(mm)

Taping style Ordering

code

(Digit 10 to

11)

(mm)

Fig.

(No.)

Pitch

(mm)

AMMO-PACK

12.70

19.05

10.0/15.0

22.5

REEL Ø 355mm 12.70 2 10.0/15.0 GY

REEL Ø 500mm

12.70

19.05

10.0/15.0

22.5/27.5

Loose, short leads 04+2 AA

Loose, long leads

(p≥15mm)

30+5

25+2/-1

Note: Ammo-pack is the preferred packaging for taped

version

Mechanical version and packaging

Internal use

Tolerance: K (±10%); M (±20%)

Mechanical version and packaging

Internal use

Tolerance: K (±10%); M (±20%)

09/2008 76

R71

MKP Series

METALLIZED POLYPROPYLENE FILM

CAPACITOR

PRODUCT CODE: R71

Rated

Cap.

630Vdc/275Vac*

Std dimensions

Ø d Max

dv/dt

Max K0

Part Number

B H L p (mm) (V/µs) (V2/µs)

0.010 µF 4.0 9.0 13.0 10.0 0.6 400 504 E3 R71PF 2100--3--

0.015 µF 4.0 9.0 13.0 10.0 0.6 400 504 E3 R71PF 2150--3--

0.022 µF 4.0 9.0 13.0 10.0 0.6 400 504 E3 R71PF 2220--3--

0.033 µF 5.0 11.0 13.0 10.0 0.6 400 504 E3 R71PF 2330--0--

0.047 µF 5.0 11.0 13.0 10.0 0.6 400 504 E3 R71PF 2470--3--

0.068 µF 6.0 12.0 13.0 10.0 0.6 400 504 E3 R71PF 2680--3--

0.1 µF 6.0 12.0 13.0 10.0 0.6 400 504 E3 R71PF 3100--3-M

0.010 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2100--0--

0.015 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2150--0--

0.022 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2220--0--

0.033 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2330--0--

0.047 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2470--0--

0.068 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 2680--0--

0.10 µF 5.0 11.0 18.0 15.0 0.6 250 315 E3 R71PI 3100--3--

0.15 µF 6.0 12.0 18.0 15.0 0.6 250 315 E3 R71PI 3150--3--

0.15 µF 6.0 17.5 18.0 15.0 0.6 250 315 E3 R71PI 3150--4--

0.22 µF 7.5 13.5 18.0 15.0 0.6 250 315 E3 R71PI 3220--3--

0.22 µF 6.0 17.5 18.0 15.0 0.6 250 315 E3 R71PI 3220--1--

0.22 µF 9.0 12.5 18.0 15.0 0.6 250 315 E3 R71PI 3220--2--

0.33 µF 8.5 14.5 18.0 15.0 0.6 250 315 E3 R71PI 3330--3--

0.33 µF 7.5 18.5 18.0 15.0 0.8 250 315 E3 R71PI 3330--1--

0.33 µF 9.0 12.5 18.0 15.0 0.6 250 315 E3 R71PI 3330--4-M

0.33 µF 13.0 12.0 18.0 15.0 0.8 250 315 E3 R71PI 3330--2--

0.47 µF 7.5 18.5 18.0 15.0 0.8 250 315 E3 R71PI 3470--4-M

0.47 µF 10.0 16.0 18.0 15.0 0.8 250 315 E3 R71PI 3470--3-M

0.68 µF 11.0 19.0 18.0 15.0 0.8 250 315 E3 R71PI 3680--3-M

0.15 µF 6.0 15.0 26.5 22.5 0.8 160 202 E3 R71PN 3150--0--

0.22 µF 6.0 15.0 26.5 22.5 0.8 160 202 E3 R71PN 3220--0--

0.33 µF 6.0 15.0 26.5 22.5 0.8 160 202 E3 R71PN 3330--3--

0.47 µF 7.0 16.0 26.5 22.5 0.8 160 202 E3 R71PN 3470--3--

0.68 µF 10.0 18.5 26.5 22.5 0.8 160 202 E3 R71PN 3680--3--

1.0 µF 10.0 18.5 26.5 22.5 0.8 160 202 E3 R71PN 4100--4-M

1.0 µF 11.0 20.0 26.5 22.5 0.8 160 202 E3 R71PN 4100--3--

0.68 µF 9.0 17.0 32.0 27.5 0.8 115 145 E3 R71PR 3680--0--

1.0 µF 11.0 20.0 32.0 27.5 0.8 115 145 E3 R71PR 4100--0--

1.5 µF 13.0 22.0 32.0 27.5 0.8 115 145 E3 R71PR 4150--0--

2.2 µF 14.0 28.0 32.0 27.5 0.8 115 145 E3 R71PR 4220--0--

3.3 µF 18.0 33.0 32.0 27.5 0.8 115 145 E3 R71PR 4330--0--

4.7 µF 22.0 37.0 32.0 27.5 0.8 115 145 E3 R71PR 4470--0--

1.5 µF 11.0 22.0 41.5 37.5 1.0 80 100 E3 R71PW 4150--0--

2.2 µF 13.0 24.0 41.5 37.5 1.0 80 100 E3 R71PW 4220--0--

3.3 µF 16.0 28.5 41.5 37.5 1.0 80 100 E3 R71PW 4330--0--

4.7 µF 19.0 32.0 41.5 37.5 1.0 80 100 E3 R71PW 4470--0--

6.8 µF 20.0 40.0 41.5 37.5 1.0 80 100 E3 R71PW 4680--0--

10.0 µF 24.0 44.0 41.5 37.5 1.0 80 100 E3 R71PW 5100--0--

15.0 µF 30.0 45.0 41.5 37.5 1.0 80 100 E3 R71PW 5150--0--

Mechanical version and packaging (table 1)

Internal use

Tolerance: K (±10%); M (±20%)

All dimensions are in mm.

Note: If the working voltage (V) is lower than the rated voltage

(VR), the capacitors may work at higher dv/dt. In this case

the maximum value allowed is obtained multiplyng the

above value (see table dv/dt) with the ratio VR/V.

The pulse characteristics K0 depends on the voltage wave-

form and in any case it cannot overcome the value given

in the above table.

* Not suitable for across-the-line applications. Please refer

to Interference Suppression Capacitors at page 145.

Rated

Cap.

1000Vdc/275Vac*

Std dimensions

Ø d Max

dv/dt

Max K0

Part Number

B H L p (mm) (V/µs) (V2/µs)

0.22 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3220--0--

0.27 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3270--0--

0.33 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3330--1--

0.33 µF 11.0 20.0 32.0 27.5 0.8 180 360 E3 R71QR3330--0--

0.39 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3390--1--

0.39 µF 11.0 20.0 32.0 27.5 0.8 180 360 E3 R71QR3390--0--

0.47 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3470--1--

0.47 µF 13.0 22.0 32.0 27.5 0.8 180 360 E3 R71QR3470--0--

0.56 µF 9.0 17.0 32.0 27.5 0.8 180 360 E3 R71QR3560--1--

0.56 µF 13.0 22.0 32.0 27.5 0.8 180 360 E3 R71QR3560--0--

0.68 µF 11.0 20.0 32.0 27.5 0.8 180 360 E3 R71QR3680--1--

0.68 µF 14.0 28.0 32.0 27.5 0.8 180 360 E3 R71QR3680--0--

0.82 µF 11.0 20.0 32.0 27.5 0.8 180 360 E3 R71QR3820--1--

0.82 µF 14.0 28.0 32.0 27.5 0.8 180 360 E3 R71QR3820--0--

1.0 µF 13.0 22.0 32.0 27.5 0.8 180 360 E3 R71QR4100--1--

1.0 µF 18.0 33.0 32.0 27.5 0.8 180 360 E3 R71QR4100--0--

1.2 µF 13.0 25.0 32.0 27.5 0.8 180 360 E3 R71QR4120--1--

1.2 µF 18.0 33.0 32.0 27.5 0.8 180 360 E3 R71QR4120--0--

1.5 µF 14.0 28.0 32.0 27.5 0.8 180 360 E3 R71QR4150--1--

1.5 µF 18.0 33.0 32.0 27.5 0.8 180 360 E3 R71QR4150--0--

1.8 µF 14.0 28.0 32.0 27.5 0.8 180 360 E3 R71QR4180--1--

1.8 µF 22.0 37.0 32.0 27.5 0.8 180 360 E3 R71QR4180--0--

2.2 µF 18.0 33.0 32.0 27.5 0.8 180 360 E3 R71QR4220--1--

2.2 µF 22.0 37.0 32.0 27.5 0.8 180 360 E3 R71QR4220--0--

2.7 µF 18.0 33.0 32.0 27.5 0.8 180 360 E3 R71QR4270--1--

3.3 µF 22.0 37.0 32.0 27.5 0.8 180 360 E3 R71QR4330--1--

3.9 µF 22.0 37.0 32.0 27.5 0.8 180 360 E3 R71QR4390--1--

0.68 µF 11.0 22.0 41.5 37.5 1.0 150 300 E3 R71QW3680--0--

0.82 µF 13.0 24.0 41.5 37.5 1.0 150 300 E3 R71QW3820--0--

1.0 µF 11.0 22.0 41.5 37.5 1.0 150 300 E3 R71QW4100--1--

1.0 µF 13.0 24.0 41.5 37.5 1.0 150 300 E3 R71QW4100--0--

1.2 µF 11.0 22.0 41.5 37.5 1.0 150 300 E3 R71QW4120--1--

1.2 µF 16.0 28.5 41.5 37.5 1.0 150 300 E3 R71QW4120--0--

1.5 µF 11.0 22.0 41.5 37.5 1.0 150 300 E3 R71QW4150--1--

1.5 µF 16.0 28.5 41.5 37.5 1.0 150 300 E3 R71QW4150--0--

1.8 µF 13.0 24.0 41.5 37.5 1.0 150 300 E3 R71QW4180--1--

1.8 µF 19.0 32.0 41.5 37.5 1.0 150 300 E3 R71QW4180--0--

2.2 µF 16.0 28.5 41.5 37.5 1.0 120 240 E3 R71QW4220--1--

2.2 µF 19.0 32.0 41.5 37.5 1.0 120 240 E3 R71QW4220--0--

2.7 µF 16.0 28.5 41.5 37.5 1.0 120 240 E3 R71QW4270--1--

2.7 µF 20.0 40.0 41.5 37.5 1.0 120 240 E3 R71QW4270--0--

3.3 µF 19.0 32.0 41.5 37.5 1.0 120 240 E3 R71QW4330--1--

3.3 µF 24.0 44.0 41.5 37.5 1.0 120 240 E3 R71QW4330--0--

3.9 µF 19.0 32.0 41.5 37.5 1.0 120 240 E3 R71QW4390--1--

3.9 µF 24.0 44.0 41.5 37.5 1.0 120 240 E3 R71QW4390--0--

4.7 µF 20.0 40.0 41.5 37.5 1.0 80 160 E3 R71QW4470--1--

4.7 µF 24.0 44.0 41.5 37.5 1.0 80 160 E3 R71QW4470--0--

5.6 µF 20.0 40.0 41.5 37.5 1.0 80 160 E3 R71QW4560--1--

5.6 µF 30.0 45.0 41.5 37.5 1.0 80 160 E3 R71QW4560--0--

6.8 µF 24.0 44.0 41.5 37.5 1.0 80 160 E3 R71QW4680--1--

8.2 µF 24.0 44.0 41.5 37.5 1.0 80 160 E3 R71QW4820--1--

10.0 µF 30.0 45.0 41.5 37.5 1.0 80 160 E3 R71QW5100--1--

Mechanical version and packaging (Table1)

Internal use

Tolerance: J (±5%); K (±10%); M (±20%)

09/2008

R71

MKP Series

METALLIZED POLYPROPYLENE FILM

CAPACITOR

MAX. VOLTAGE (Vr.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th ≤ 40°C)

Note: p (pitch) in mm.

09/2008 78

MAX. CURRENT (Ir.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th ≤ 40°C)

Note: p (pitch) in mm.

R71

MKP Series

METALLIZED POLYPROPYLENE FILM

CAPACITOR