LMC6442AIMNOPB - NATIONAL SEMICONDUCTOR

LMC6082

LMC6082 Precision CMOS Dual Operational Amplifier

Literature Number: SNOS630C

LMC6082

Precision CMOS Dual Operational Amplifier

General Description

The LMC6082 is a precision dual low offset voltage opera-

tional amplifier, capable of single supply operation. Perfor-

mance characteristics include ultra low input bias current,

high voltage gain, rail-to-rail output swing, and an input

common mode voltage range that includes ground. These

features, plus its low offset voltage, make the LMC6082

ideally suited for precision circuit applications.

Other applications using the LMC6082 include precision full-

wave rectifiers, integrators, references, and sample-and-

hold circuits.

This device is built with National’s advanced Double-Poly

Silicon-Gate CMOS process.

For designs with more critical power demands, see the

LMC6062 precision dual micropower operational amplifier.

PATENT PENDING

Features

(Typical unless otherwise stated)

nLow offset voltage: 150 µV

nOperates from 4.5V to 15V single supply

nUltra low input bias current: 10 fA

nOutput swing to within 20 mV of supply rail, 100k load

nInput common-mode range includes V

−

nHigh voltage gain: 130 dB

nImproved latchup immunity

Applications

nInstrumentation amplifier

nPhotodiode and infrared detector preamplifier

nTransducer amplifiers

nMedical instrumentation

nD/A converter

nCharge amplifier for piezoelectric transducers

Connection Diagram

8-Pin DIP/SO

01129701

Top View

Input Bias Current

vs Temperature

01129718

August 2000

LMC6082 Precision CMOS Dual Operational Amplifier

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Differential Input Voltage ±Supply Voltage

Voltage at Input/Output Pin (V

) +0.3V,

−

) −0.3V

Supply Voltage (V

−V

−

) 16V

Output Short Circuit to V

(Note 11)

Output Short Circuit to V

−

(Note 2)

Lead Temperature

(Soldering, 10 Sec.) 260˚C

Storage Temp. Range −65˚C to +150˚C

Junction Temperature 150˚C

ESD Tolerance (Note 4) 2 kV

Current at Input Pin ±10 mA

Current at Output Pin ±30 mA

Current at Power Supply Pin 40 mA

Power Dissipation (Note 3)

Operating Ratings (Note 1)

Temperature Range

LMC6082AM −55˚C ≤T

≤

+125˚C

LMC6082AI, LMC6082I −40˚C ≤T

≤+85˚C

Supply Voltage 4.5V ≤V

≤15.5V

Thermal Resistance (θ

) (Note

12)

8-Pin Molded DIP 115˚C/W

8-Pin SO 193˚C/W

Power Dissipation (Note 10)

DC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for T

= 25˚C. Boldface limits apply at the temperature extremes. V

= 5V, V

−

= 0V, V

= 1.5V, V

= 2.5V and R

>1M unless otherwise specified.

Typ LMC6082AM LMC6082AI LMC6082I

Symbol Parameter Conditions (Note 5) Limit Limit Limit Units

(Note 6) (Note 6) (Note 6)

Input Offset Voltage 150 350 350 800 µV

1000 800 1300 Max

TCV

Input Offset Voltage 1.0 µV/˚C

Average Drift

Input Bias Current 0.010 pA

100 4 4 Max

Input Offset Current 0.005 pA

100 2 2 Max

Input Resistance >10 Tera Ω

CMRR Common Mode 0V ≤V

≤12.0V 85 75 75 66 dB

Rejection Ratio V

= 15V 72 72 63 Min

+PSRR Positive Power Supply 5V ≤V

≤15V 85 75 75 66 dB

Rejection Ratio V

= 2.5V 72 72 63 Min

−PSRR Negative Power Supply 0V ≤V

−

≤−10V 94 84 84 74 dB

Rejection Ratio 81 81 71 Min

Input Common-Mode V

= 5V and 15V −0.4 −0.1 −0.1 −0.1 V

Voltage Range for CMRR ≥60 dB 000Max

− 1.9 V

− 2.3 V

− 2.6 V

− 2.5 V

− 2.5 Min

Large Signal R

=2kΩSourcing 1400 400 400 300 V/mV

Voltage Gain (Note 7) 300 300 200 Min

Sinking 350 180 180 90 V/mV

70 100 60 Min

= 600ΩSourcing 1200 400 400 200 V/mV

(Note 7) 150 150 80 Min

Sinking 150 100 100 70 V/mV

35 50 35 Min

LMC6082

www.national.com 2

DC Electrical Characteristics (Continued)

Unless otherwise specified, all limits guaranteed for T

= 25˚C. Boldface limits apply at the temperature extremes. V

= 5V, V

−

= 0V, V

= 1.5V, V

= 2.5V and R

>1M unless otherwise specified.

Typ LMC6082AM LMC6082AI LMC6082I

Symbol Parameter Conditions (Note 5) Limit Limit Limit Units

(Note 6) (Note 6) (Note 6)

Output Swing V

= 5V 4.87 4.80 4.80 4.75 V

=2kΩto 2.5V 4.70 4.73 4.67 Min

0.10 0.13 0.13 0.20 V

0.19 0.17 0.24 Max

= 5V 4.61 4.50 4.50 4.40 V

= 600Ωto 2.5V 4.24 4.31 4.21 Min

0.30 0.40 0.40 0.50 V

0.63 0.50 0.63 Max

= 15V 14.63 14.50 14.50 14.37 V

=2kΩto 7.5V 14.30 14.34 14.25 Min

0.26 0.35 0.35 0.44 V

0.48 0.45 0.56 Max

= 15V 13.90 13.35 13.35 12.92 V

= 600Ωto 7.5V 12.80 12.86 12.44 Min

0.79 1.16 1.16 1.33 V

1.42 1.32 1.58 Max

Output Current Sourcing, V

=0V 22 16 16 13 mA

=5V 8108Min

Sinking, V

=5V 21 16 16 13 mA

11 13 10 Min

Output Current Sourcing, V

=0V 30 28 28 23 mA

= 15V 18 22 18 Min

Sinking, V

= 13V 34 28 28 23 mA

(Note 11) 19 22 18 Min

Supply Current Both Amplifiers 0.9 1.5 1.5 1.5 mA

= +5V, V

= 1.5V 1.8 1.8 1.8 Max

Both Amplifiers 1.1 1.7 1.7 1.7 mA

= +15V, V

= 7.5V 222Max

LMC6082

www.national.com3

AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for T

= 25˚C, Boldface limits apply at the temperature extremes. V

= 5V, V

−

= 0V, V

= 1.5V, V

= 2.5V and R

>1M unless otherwise specified.

Typ LMC6082AM LMC6082AI LMC6082I

Symbol Parameter Conditions (Note 5) Limit Limit Limit Units

(Note 6) (Note 6) (Note 6)

SR Slew Rate (Note 8) 1.5 0.8 0.8 0.8 V/µs

0.5 0.6 0.6 Min

GBW Gain-Bandwidth Product 1.3 MHz

Phase Margin 50 Deg

Amp-to-Amp Isolation (Note 9) 140 dB

Input-Referred

Voltage Noise

F = 1 kHz 22

Input-Referred

Current Noise

F = 1 kHz 0.0002

T.H.D. Total Harmonic

Distortion

F = 10 kHz, A

= −10

=2kΩ,V

=8V

0.01 %

±5V Supply

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The

guaranteed specifications apply only for the test conditions listed.

Note 2: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the

maximum allowed junction temperature of 150˚C. Output currents in excess of ±30 mA over long term may adversely affect reliability.

Note 3: The maximum power dissipation is a function of TJ(Max),θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD=(T

J(Max)

−T

A)/θJA.

Note 4: Human body model, 1.5 kΩin series with 100 pF.

Note 5: Typical values represent the most likely parametric norm.

Note 6: All limits are guaranteed by testing or statistical analysis.

Note 7: V+= 15V, VCM = 7.5V and RLconnected to 7.5V. For Sourcing tests, 7.5V ≤VO≤11.5V. For Sinking tests, 2.5V ≤VO≤7.5V.

Note 8: V+= 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates.

Note 9: Input referred V+= 15V and RL= 100 kΩconnected to 7.5V. Each amp excited in turm with 1 kHz to produce VO=12V

PP.

Note 10: For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD=(T

J−T

A)/θJA. All numbers apply for

packages soldered directly into a PC board.

Note 11: Do not connect output to V+, when V+is greater than 13V or reliability will be adversely affected.

Note 12: All numbers apply for packages soldered directly into a PC board.

LMC6082

www.national.com 4

Typical Performance Characteristics

=±7.5V, T

= 25˚C, Unless otherwise specified

Distribution of LMC6082

Input Offset Voltage

= +25˚C)

Distribution of LMC6082

Input Offset Voltage

= −55˚C)

01129715 01129716

Distribution of LMC6082

Input Offset Voltage

= +125˚C)

Input Bias Current

vs Temperature

01129717

01129718

Supply Current

vs Supply Voltage

Input Voltage

vs Output Voltage

01129719 01129720

LMC6082

www.national.com5

Typical Performance Characteristics V

=±7.5V, T

= 25˚C, Unless otherwise

specified (Continued)

Common Mode

Rejection Ratio

vs Frequency

Power Supply Rejection

Ratio vs Frequency

01129721 01129722

Input Voltage Noise

vs Frequency

Output Characteristics

Sourcing Current

01129723 01129724

Output Characteristics

Sinking Current

Gain and Phase Response

vs Temperature

(−55˚C to +125˚C)

01129725

01129726

LMC6082

www.national.com 6

Typical Performance Characteristics V

=±7.5V, T

= 25˚C, Unless otherwise

specified (Continued)

Gain and Phase

Response vs Capacitive Load

with R

= 600Ω

Gain and Phase

Response vs Capacitive Load

with R

= 500 kΩ

01129727 01129728

Open Loop

Frequency Response

Inverting Small Signal

Pulse Response

01129729 01129730

Inverting Large Signal

Pulse Response

Non-Inverting Small

Signal Pulse Response

01129731 01129732

LMC6082

www.national.com7

Typical Performance Characteristics V

=±7.5V, T

= 25˚C, Unless otherwise

specified (Continued)

Non-Inverting Large

Signal Pulse Response

Crosstalk Rejection

vs Frequency

01129733 01129734

Stability vs Capacitive

Load, R

= 600Ω

Stability vs Capacitive

Load R

=1MΩ

01129735 01129736

Applications Hints

AMPLIFIER TOPOLOGY

The LMC6082 incorporates a novel op-amp design topology

that enables it to maintain rail to rail output swing even when

driving a large load. Instead of relying on a push-pull unity

gain output buffer stage, the output stage is taken directly

from the internal integrator, which provides both low output

impedance and large gain. Special feed-forward compensa-

tion design techniques are incorporated to maintain stability

over a wider range of operating conditions than traditional

micropower op-amps. These features make the LMC6082

both easier to design with, and provide higher speed than

products typically found in this ultra-low power class.

COMPENSATING FOR INPUT CAPACITANCE

It is quite common to use large values of feedback resis-

tance for amplifiers with ultra-low input current, like the

LMC6082.

Although the LMC6082 is highly stable over a wide range of

operating conditions, certain precautions must be met to

achieve the desired pulse response when a large feedback

resistor is used. Large feedback resistors and even small

values of input capacitance, due to transducers, photo-

diodes, and circuit board parasitics, reduce phase margins.

When high input impedances are demanded, guarding of the

LMC6082 is suggested. Guarding input lines will not only

reduce leakage, but lowers stray input capacitance as well.

(See Printed-Circuit-Board Layout for High Impedance

Work).

The effect of input capacitance can be compensated for by

adding a capacitor, C

, around the feedback resistors (as in

Figure 1 ) such that:

≤R

Since it is often difficult to know the exact value of C

can

be experimentally adjusted so that the desired pulse re-

sponse is achieved. Refer to the LMC660 and LMC662 for a

more detailed discussion on compensating for input capaci-

tance.

LMC6082

www.national.com 8

Applications Hints (Continued)

CAPACITIVE LOAD TOLERANCE

All rail-to-rail output swing operational amplifiers have volt-

age gain in the output stage. A compensation capacitor is

normally included in this integrator stage. The frequency

location of the dominant pole is affected by the resistive load

on the amplifier. Capacitive load driving capability can be

optimized by using an appropriate resistive load in parallel

with the capacitive load (see typical curves).

Direct capacitive loading will reduce the phase margin of

many op-amps. A pole in the feedback loop is created by the

combination of the op-amp’s output impedance and the ca-

pacitive load. This pole induces phase lag at the unity-gain

crossover frequency of the amplifier resulting in either an

oscillatory or underdamped pulse response. With a few ex-

ternal components, op amps can easily indirectly drive ca-

pacitive loads, as shown in Figure 2.

In the circuit of Figure 2, R1 and C1 serve to counteract the

loss of phase margin by feeding the high frequency compo-

nent of the output signal back to the amplifier’s inverting

input, thereby preserving phase margin in the overall feed-

back loop.

Capacitive load driving capability is enhanced by using a

pull up resistor to V

Figure 3. Typically a pull up resistor

conducting 500 µA or more will significantly improve capaci-

tive load responses. The value of the pull up resistor must be

determined based on the current sinking capability of the

amplifier with respect to the desired output swing. Open loop

gain of the amplifier can also be affected by the pull up

resistor (see Electrical Characteristics).

PRINTED-CIRCUIT-BOARD LAYOUT

FOR HIGH-IMPEDANCE WORK

It is generally recognized that any circuit which must operate

with less than 1000 pA of leakage current requires special

layout of the PC board. When one wishes to take advantage

of the ultra-low bias current of the LMC6082, typically less

than 10 fA, it is essential to have an excellent layout. Fortu-

nately, the techniques of obtaining low leakages are quite

simple. First, the user must not ignore the surface leakage of

the PC board, even though it may sometimes appear accept-

ably low, because under conditions of high humidity or dust

or contamination, the surface leakage will be appreciable.

To minimize the effect of any surface leakage, lay out a ring

of foil completely surrounding the LMC6082’s inputs and the

terminals of capacitors, diodes, conductors, resistors, relay

terminals, etc. connected to the op-amp’s inputs, as in Fig-

ure 4. To have a significant effect, guard rings should be

placed on both the top and bottom of the PC board. This PC

foil must then be connected to a voltage which is at the same

voltage as the amplifier inputs, since no leakage current can

flow between two points at the same potential. For example,

a PC board trace-to-pad resistance of 10

Ω, which is nor-

mally considered a very large resistance, could leak 5 pA if

the trace were a 5V bus adjacent to the pad of the input. This

would cause a 100 times degradation from the LMC6082’s

actual performance. However, if a guard ring is held within

5 mV of the inputs, then even a resistance of 10

Ωwould

cause only 0.05 pA of leakage current. See Figure 5 for

typical connections of guard rings for standard op-amp con-

figurations.

01129704

FIGURE 1. Cancelling the Effect of Input Capacitance

01129705

FIGURE 2. LMC6082 Noninverting Gain of 10 Amplifier,

Compensated to Handle Capacitive Loads

01129714

FIGURE 3. Compensating for Large Capacitive Loads

with a Pull Up Resistor

LMC6082

www.national.com9

Applications Hints (Continued)

The designer should be aware that when it is inappropriate

to lay out a PC board for the sake of just a few circuits, there

is another technique which is even better than a guard ring

on a PC board: Don’t insert the amplifier’s input pin into the

board at all, but bend it up in the air and use only air as an

insulator. Air is an excellent insulator. In this case you may

have to forego some of the advantages of PC board con-

struction, but the advantages are sometimes well worth the

effort of using point-to-point up-in-the-air

wiring. See Figure 6.

Latchup

CMOS devices tend to be susceptible to latchup due to their

internal parasitic SCR effects. The (I/O) input and output pins

look similar to the gate of the SCR. There is a minimum

current required to trigger the SCR gate lead. The LMC6062

and LMC6082 are designed to withstand 100 mA surge

current on the I/O pins. Some resistive method should be

used to isolate any capacitance from supplying excess cur-

rent to the I/O pins. In addition, like an SCR, there is a

minimum holding current for any latchup mode. Limiting

current to the supply pins will also inhibit latchup suscepti-

bility.

Typical Single-Supply Applications

= 5.0 V

)

The extremely high input impedance, and low power con-

sumption, of the LMC6082 make it ideal for applications that

require battery-powered instrumentation amplifiers. Ex-

amples of these types of applications are hand-held pH

probes, analytic medical instruments, magnetic field detec-

tors, gas detectors, and silicon based pressure transducers.

Figure 7 shows an instrumentation amplifier that features

high differential and common mode input resistance

(>10

Ω), 0.01% gain accuracy at A

= 1000, excellent

CMRR with 1 kΩimbalance in bridge source resistance.

Input current is less than 100 fA and offset drift is less than

2.5 µV/˚C. R

provides a simple means of adjusting gain

over a wide range without degrading CMRR. R

is an initial

trim used to maximize CMRR without using super precision

matched resistors. For good CMRR over temperature, low

drift resistors should be used.

01129706

FIGURE 4. Example of Guard Ring in P.C. Board

Layout

01129707

Inverting Amplifier

01129708

Non-Inverting Amplifier

01129709

Follower

FIGURE 5. Typical Connections of Guard Rings

01129710

(Input pins are lifted out of PC board and soldered directly to components.

All other pins connected to PC board).

FIGURE 6. Air Wiring

LMC6082

www.national.com 10

Typical Single-Supply Applications (Continued)

Typical Single-Supply Applications

= 5.0 V

)

01129711

If R1=R

5,R

3=R

6, and R4=R

7; then

∴AV≈100 for circuit shown (R2= 9.822k).

FIGURE 7. Instrumentation Amplifier

01129712

FIGURE 8. Low-Leakage Sample and Hold

LMC6082

www.national.com11

Typical Single-Supply Applications (V

= 5.0 V

) (Continued)

Ordering Information

Package Temperature Range NSC

Drawing

Transport

Media

Military Industrial

−55˚C to +125˚C −40˚C to +85˚C

8-Pin LMC6082AIN N08E Rail

Molded DIP LMC6082IN

8-Pin LMC6082AIM,

LMC6082AIMX, M08A Rail

Small Outline LMC6082IM,

LMC6082IMX

Tape and Reel

For MIL-STD-883C qualified products, please contact your local National

Semiconductor Sales Office or Distributor for availability and specification

information.

01129713

FIGURE 9. 1 Hz Square Wave Oscillator

LMC6082

www.national.com 12

Physical Dimensions inches (millimeters) unless otherwise noted

8-Pin Small Outline Package

Order Number LMC6082AIM, LMC6082AIMX, LMC6082IM or LMC6082IMX

NS Package Number M08A

8-Pin Molded Dual-In-Line Package

Order Number LMC6082AIN or LMC6082IN

NS Package Number N08E

LMC6082

www.national.com13

Notes

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves

the right at any time without notice to change said circuitry and specifications.

For the most current product information visit us at www.national.com.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS

WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR

CORPORATION. As used herein:

1. Life support devices or systems are devices or systems

which, (a) are intended for surgical implant into the body, or

(b) support or sustain life, and whose failure to perform when

properly used in accordance with instructions for use

provided in the labeling, can be reasonably expected to result

in a significant injury to the user.

2. A critical component is any component of a life support

device or system whose failure to perform can be reasonably

expected to cause the failure of the life support device or

system, or to affect its safety or effectiveness.

BANNED SUBSTANCE COMPLIANCE

National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship

Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned

Substances’’ as defined in CSP-9-111S2.

National Semiconductor

Americas Customer

Support Center

Email: new.feedback@nsc.com

Tel: 1-800-272-9959

National Semiconductor

Europe Customer Support Center

Fax: +49 (0) 180-530 85 86

Email: europe.support@nsc.com

Deutsch Tel: +49 (0) 69 9508 6208

English Tel: +44 (0) 870 24 0 2171

Français Tel: +33 (0) 1 41 91 8790

National Semiconductor

Asia Pacific Customer

Support Center

Email: ap.support@nsc.com

National Semiconductor

Japan Customer Support Center

Fax: 81-3-5639-7507

Email: jpn.feedback@nsc.com

Tel: 81-3-5639-7560

www.national.com

LMC6082 Precision CMOS Dual Operational Amplifier

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265