To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. User's Manual 16 R8C/26 Group, R8C/27 Group Hardware Manual RENESAS 16-BIT SINGLE-CHIP MCU R8C FAMILY / R8C/2x SERIES All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp. through various means, including the Renesas Electronics Corp. website (http://www.renesas.com). Rev.2.10 2008.09 Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. General Precautions in the Handling of MPU/MCU Products The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes on the products covered by this manual, refer to the relevant sections of the manual. If the descriptions under General Precautions in the Handling of MPU/MCU Products and in the body of the manual differ from each other, the description in the body of the manual takes precedence. 1. Handling of Unused Pins Handle unused pins in accord with the directions given under Handling of Unused Pins in the manual. The input pins of CMOS products are generally in the high-impedance state. In operation with an unused pin in the open-circuit state, extra electromagnetic noise is induced in the vicinity of LSI, an associated shoot-through current flows internally, and malfunctions occur due to the false recognition of the pin state as an input signal become possible. Unused pins should be handled as described under Handling of Unused Pins in the manual. 2. Processing at Power-on The state of the product is undefined at the moment when power is supplied. The states of internal circuits in the LSI are indeterminate and the states of register settings and pins are undefined at the moment when power is supplied. In a finished product where the reset signal is applied to the external reset pin, the states of pins are not guaranteed from the moment when power is supplied until the reset process is completed. In a similar way, the states of pins in a product that is reset by an on-chip power-on reset function are not guaranteed from the moment when power is supplied until the power reaches the level at which resetting has been specified. 3. Prohibition of Access to Reserved Addresses Access to reserved addresses is prohibited. The reserved addresses are provided for the possible future expansion of functions. Do not access these addresses; the correct operation of LSI is not guaranteed if they are accessed. 4. Clock Signals After applying a reset, only release the reset line after the operating clock signal has become stable. When switching the clock signal during program execution, wait until the target clock signal has stabilized. When the clock signal is generated with an external resonator (or from an external oscillator) during a reset, ensure that the reset line is only released after full stabilization of the clock signal. Moreover, when switching to a clock signal produced with an external resonator (or by an external oscillator) while program execution is in progress, wait until the target clock signal is stable. 5. Differences between Products Before changing from one product to another, i.e. to one with a different part number, confirm that the change will not lead to problems. The characteristics of MPU/MCU in the same group but having different part numbers may differ because of the differences in internal memory capacity and layout pattern. When changing to products of different part numbers, implement a system-evaluation test for each of the products. How to Use This Manual 1. Purpose and Target Readers This manual is designed to provide the user with an understanding of the hardware functions and electrical characteristics of the MCU. It is intended for users designing application systems incorporating the MCU. A basic knowledge of electric circuits, logical circuits, and MCUs is necessary in order to use this manual. The manual comprises an overview of the product; descriptions of the CPU, system control functions, peripheral functions, and electrical characteristics; and usage notes. Particular attention should be paid to the precautionary notes when using the manual. These notes occur within the body of the text, at the end of each section, and in the Usage Notes section. The revision history summarizes the locations of revisions and additions. It does not list all revisions. Refer to the text of the manual for details. The following documents apply to the R8C/26 Group, R8C/27 Group. Make sure to refer to the latest versions of these documents. The newest versions of the documents listed may be obtained from the Renesas Technology Web site. Document Type Datasheet Description Document Title Document No. Hardware overview and electrical characteristics R8C/26, R8C/27 REJ03B0168 Group Datasheet This hardware R8C/26 Group, Hardware manual Hardware specifications (pin assignments, manual R8C/27 Group memory maps, peripheral function Hardware Manual specifications, electrical characteristics, timing charts) and operation description Note: Refer to the application notes for details on using peripheral functions. Software manual Description of CPU instruction set R8C/Tiny Series REJ09B0001 Software Manual Available from Renesas Application note Information on using peripheral functions and Technology Web site. application examples Sample programs Information on writing programs in assembly language and C Renesas Product specifications, updates on documents, technical update etc. 2. Notation of Numbers and Symbols The notation conventions for register names, bit names, numbers, and symbols used in this manual are described below. (1) Register Names, Bit Names, and Pin Names Registers, bits, and pins are referred to in the text by symbols. The symbol is accompanied by the word "register," "bit," or "pin" to distinguish the three categories. Examples the PM03 bit in the PM0 register P3_5 pin, VCC pin (2) Notation of Numbers The indication "b" is appended to numeric values given in binary format. However, nothing is appended to the values of single bits. The indication "h" is appended to numeric values given in hexadecimal format. Nothing is appended to numeric values given in decimal format. Examples Binary: 11b Hexadecimal: EFA0h Decimal: 1234 3. Register Notation The symbols and terms used in register diagrams are described below. XXX Register b7 b6 b5 b4 b3 *1 b2 b1 b0 Symbol XXX 0 Bit Symbol XXX0 Address XXX Bit Name XXX bits XXX1 After Reset 00h Function RW 1 0: XXX 0 1: XXX 1 0: Do not set. 1 1: XXX RW RW (b2) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. (b3) Reserved bits Set to 0. RW XXX bits Function varies according to the operating mode. RW XXX4 *3 XXX5 WO XXX6 RW XXX7 XXX bit *2 b1 b0 0: XXX 1: XXX *4 RO *1 Blank: Set to 0 or 1 according to the application. 0: Set to 0. 1: Set to 1. X: Nothing is assigned. *2 RW: Read and write. RO: Read only. WO: Write only. -: Nothing is assigned. *3 * Reserved bit Reserved bit. Set to specified value. *4 * Nothing is assigned Nothing is assigned to the bit. As the bit may be used for future functions, if necessary, set to 0. * Do not set to a value Operation is not guaranteed when a value is set. * Function varies according to the operating mode. The function of the bit varies with the peripheral function mode. Refer to the register diagram for information on the individual modes. 4. List of Abbreviations and Acronyms Abbreviation ACIA bps CRC DMA DMAC GSM Hi-Z IEBus I/O IrDA LSB MSB NC PLL PWM SIM UART VCO Full Form Asynchronous Communication Interface Adapter bits per second Cyclic Redundancy Check Direct Memory Access Direct Memory Access Controller Global System for Mobile Communications High Impedance Inter Equipment Bus Input / Output Infrared Data Association Least Significant Bit Most Significant Bit Non-Connect Phase Locked Loop Pulse Width Modulation Subscriber Identity Module Universal Asynchronous Receiver / Transmitter Voltage Controlled Oscillator All trademarks and registered trademarks are the property of their respective owners. Table of Contents SFR Page Reference ........................................................................................................................... B - 1 1. Overview ......................................................................................................................................... 1 1.1 1.2 1.3 1.4 1.5 1.6 2. Applications ............................................................................................................................................... 1 Performance Overview .............................................................................................................................. 2 Block Diagram .......................................................................................................................................... 4 Product Information .................................................................................................................................. 5 Pin Assignments ........................................................................................................................................ 9 Pin Functions ........................................................................................................................................... 10 Central Processing Unit (CPU) ..................................................................................................... 12 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.8.1 2.8.2 2.8.3 2.8.4 2.8.5 2.8.6 2.8.7 2.8.8 2.8.9 2.8.10 3. Data Registers (R0, R1, R2, and R3) ...................................................................................................... Address Registers (A0 and A1) ............................................................................................................... Frame Base Register (FB) ....................................................................................................................... Interrupt Table Register (INTB) .............................................................................................................. Program Counter (PC) ............................................................................................................................. User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) .................................................................. Static Base Register (SB) ........................................................................................................................ Flag Register (FLG) ................................................................................................................................ Carry Flag (C) ..................................................................................................................................... Debug Flag (D) ................................................................................................................................... Zero Flag (Z) ....................................................................................................................................... Sign Flag (S) ....................................................................................................................................... Register Bank Select Flag (B) ............................................................................................................ Overflow Flag (O) .............................................................................................................................. Interrupt Enable Flag (I) ..................................................................................................................... Stack Pointer Select Flag (U) .............................................................................................................. Processor Interrupt Priority Level (IPL) ............................................................................................. Reserved Bit ........................................................................................................................................ 13 13 13 13 13 13 13 13 13 13 13 13 13 13 14 14 14 14 Memory ......................................................................................................................................... 15 3.1 3.2 R8C/26 Group ......................................................................................................................................... 15 R8C/27 Group ......................................................................................................................................... 16 4. Special Function Registers (SFRs) ............................................................................................... 17 5. Resets ........................................................................................................................................... 24 5.1 5.1.1 5.1.2 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Hardware Reset ....................................................................................................................................... When Power Supply is Stable ............................................................................................................. Power On ............................................................................................................................................ Power-On Reset Function ....................................................................................................................... Voltage Monitor 0 Reset (N, D Version) ................................................................................................ Voltage Monitor 1 Reset (N, D Version) ................................................................................................ Voltage Monitor 1 Reset (J, K Version) .................................................................................................. Voltage Monitor 2 Reset ......................................................................................................................... Watchdog Timer Reset ............................................................................................................................ Software Reset ......................................................................................................................................... A-1 28 28 28 30 32 32 32 33 33 33 6. Voltage Detection Circuit .............................................................................................................. 34 6.1 6.1.1 6.1.2 6.1.3 6.2 6.3 6.4 6.5 7. VCC Input Voltage .................................................................................................................................. Monitoring Vdet0 ............................................................................................................................... Monitoring Vdet1 ............................................................................................................................... Monitoring Vdet2 ............................................................................................................................... Voltage Monitor 0 Reset (For N, D Version Only) ................................................................................. Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset (N, D Version) ............................................ Voltage Monitor 1 Reset (J, K Version) .................................................................................................. Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset ..................................................................... 45 45 45 45 46 47 49 50 Programmable I/O Ports ............................................................................................................... 52 7.1 7.2 7.3 7.4 7.5 8. Functions of Programmable I/O Ports ..................................................................................................... Effect on Peripheral Functions ................................................................................................................ Pins Other than Programmable I/O Ports ................................................................................................ Port Setting .............................................................................................................................................. Unassigned Pin Handling ........................................................................................................................ 52 53 53 65 76 Processor Mode ............................................................................................................................ 77 8.1 Processor Modes ...................................................................................................................................... 77 9. Bus ................................................................................................................................................ 78 10. Clock Generation Circuit ............................................................................................................... 79 10.1 10.2 10.2.1 10.2.2 10.3 10.4 10.4.1 10.4.2 10.4.3 10.4.4 10.4.5 10.4.6 10.4.7 10.4.8 10.4.9 10.5 10.5.1 10.5.2 10.5.3 10.6 10.6.1 10.7 10.7.1 10.7.2 10.7.3 10.7.4 XIN Clock ............................................................................................................................................... 89 On-Chip Oscillator Clocks ...................................................................................................................... 90 Low-Speed On-Chip Oscillator Clock ................................................................................................ 90 High-Speed On-Chip Oscillator Clock ............................................................................................... 90 XCIN Clock (For N, D Version Only) .................................................................................................... 91 CPU Clock and Peripheral Function Clock ............................................................................................. 92 System Clock ...................................................................................................................................... 92 CPU Clock .......................................................................................................................................... 92 Peripheral Function Clock (f1, f2, f4, f8, and f32) ............................................................................. 92 fOCO ................................................................................................................................................... 92 fOCO40M ........................................................................................................................................... 92 fOCO-F ............................................................................................................................................... 92 fOCO-S ............................................................................................................................................... 92 fC4 and fC32 ....................................................................................................................................... 93 fOCO128 ............................................................................................................................................. 93 Power Control .......................................................................................................................................... 94 Standard Operating Mode ................................................................................................................... 94 Wait Mode .......................................................................................................................................... 96 Stop Mode ......................................................................................................................................... 100 Oscillation Stop Detection Function ..................................................................................................... 104 How to Use Oscillation Stop Detection Function ............................................................................. 104 Notes on Clock Generation Circuit ....................................................................................................... 108 Stop Mode ......................................................................................................................................... 108 Wait Mode ........................................................................................................................................ 108 Oscillation Stop Detection Function ................................................................................................. 108 Oscillation Circuit Constants ............................................................................................................ 108 A-2 11. Protection .................................................................................................................................... 109 12. Interrupts ...................................................................................................................................... 110 12.1 12.1.1 12.1.2 12.1.3 12.1.4 12.1.5 12.1.6 12.2 12.2.1 12.2.2 12.3 12.4 12.5 12.6 12.6.1 12.6.2 12.6.3 12.6.4 12.6.5 13. 13.1 13.2 14. Interrupt Overview ................................................................................................................................ 110 Types of Interrupts ............................................................................................................................ 110 Software Interrupts ........................................................................................................................... 111 Special Interrupts .............................................................................................................................. 112 Peripheral Function Interrupt ............................................................................................................ 112 Interrupts and Interrupt Vectors ........................................................................................................ 113 Interrupt Control ............................................................................................................................... 115 INT Interrupt ......................................................................................................................................... 124 INTi Interrupt (i = 0, 1, 3) ................................................................................................................. 124 INTi Input Filter (i = 0, 1, 3) ............................................................................................................. 126 Key Input Interrupt ................................................................................................................................ 127 Address Match Interrupt ........................................................................................................................ 129 Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupts, and I2C bus Interface Interrupt (Interrupts with Multiple Interrupt Request Sources) ............................................................ 131 Notes on Interrupts ................................................................................................................................ 133 Reading Address 00000h .................................................................................................................. 133 SP Setting .......................................................................................................................................... 133 External Interrupt and Key Input Interrupt ....................................................................................... 133 Changing Interrupt Sources .............................................................................................................. 134 Changing Interrupt Control Register Contents ................................................................................. 135 Watchdog Timer .......................................................................................................................... 136 Count Source Protection Mode Disabled .............................................................................................. 139 Count Source Protection Mode Enabled ............................................................................................... 140 Timers ......................................................................................................................................... 141 14.1 Timer RA ............................................................................................................................................... 14.1.1 Timer Mode ...................................................................................................................................... 14.1.2 Pulse Output Mode ........................................................................................................................... 14.1.3 Event Counter Mode ......................................................................................................................... 14.1.4 Pulse Width Measurement Mode ...................................................................................................... 14.1.5 Pulse Period Measurement Mode ..................................................................................................... 14.1.6 Notes on Timer RA ........................................................................................................................... 14.2 Timer RB ............................................................................................................................................... 14.2.1 Timer Mode ...................................................................................................................................... 14.2.2 Programmable Waveform Generation Mode .................................................................................... 14.2.3 Programmable One-shot Generation Mode ...................................................................................... 14.2.4 Programmable Wait One-Shot Generation Mode ............................................................................. 14.2.5 Notes on Timer RB ........................................................................................................................... 14.3 Timer RC ............................................................................................................................................... 14.3.1 Overview ........................................................................................................................................... 14.3.2 Registers Associated with Timer RC ................................................................................................ 14.3.3 Common Items for Multiple Modes ................................................................................................. 14.3.4 Timer Mode (Input Capture Function) ............................................................................................. 14.3.5 Timer Mode (Output Compare Function) ......................................................................................... 14.3.6 PWM Mode ....................................................................................................................................... A-3 143 146 148 150 152 155 158 159 163 166 169 173 177 181 181 183 193 199 204 210 14.3.7 PWM2 Mode ..................................................................................................................................... 14.3.8 Timer RC Interrupt ........................................................................................................................... 14.3.9 Notes on Timer RC ........................................................................................................................... 14.4 Timer RE ............................................................................................................................................... 14.4.1 Real-Time Clock Mode (For N, D Version Only) ............................................................................ 14.4.2 Output Compare Mode ..................................................................................................................... 14.4.3 Notes on Timer RE ........................................................................................................................... 15. Serial Interface ............................................................................................................................ 241 15.1 Clock Synchronous Serial I/O Mode ..................................................................................................... 15.1.1 Polarity Select Function .................................................................................................................... 15.1.2 LSB First/MSB First Select Function ............................................................................................... 15.1.3 Continuous Receive Mode ................................................................................................................ 15.2 Clock Asynchronous Serial I/O (UART) Mode .................................................................................... 15.2.1 Bit Rate ............................................................................................................................................. 15.3 Notes on Serial Interface ....................................................................................................................... 16. 248 251 251 252 253 257 258 Clock Synchronous Serial Interface ............................................................................................ 259 16.1 Mode Selection ...................................................................................................................................... 16.2 Clock Synchronous Serial I/O with Chip Select (SSU) ........................................................................ 16.2.1 Transfer Clock .................................................................................................................................. 16.2.2 SS Shift Register (SSTRSR) ............................................................................................................. 16.2.3 Interrupt Requests ............................................................................................................................. 16.2.4 Communication Modes and Pin Functions ....................................................................................... 16.2.5 Clock Synchronous Communication Mode ...................................................................................... 16.2.6 Operation in 4-Wire Bus Communication Mode .............................................................................. 16.2.7 SCS Pin Control and Arbitration ...................................................................................................... 16.2.8 Notes on Clock Synchronous Serial I/O with Chip Select ............................................................... 16.3 I2C bus Interface .................................................................................................................................... 16.3.1 Transfer Clock .................................................................................................................................. 16.3.2 Interrupt Requests ............................................................................................................................. 16.3.3 I2C bus Interface Mode ..................................................................................................................... 16.3.4 Clock Synchronous Serial Mode ...................................................................................................... 16.3.5 Noise Canceller ................................................................................................................................. 16.3.6 Bit Synchronization Circuit .............................................................................................................. 16.3.7 Examples of Register Setting ............................................................................................................ 16.3.8 Notes on I2C bus Interface ................................................................................................................ 17. 215 221 222 223 224 232 238 259 260 270 272 273 274 275 282 288 289 290 300 301 302 313 316 317 318 322 Hardware LIN .............................................................................................................................. 323 17.1 17.2 17.3 17.4 17.4.1 17.4.2 17.4.3 17.4.4 17.5 17.6 Features ................................................................................................................................................. Input/Output Pins .................................................................................................................................. Register Configuration .......................................................................................................................... Functional Description .......................................................................................................................... Master Mode ..................................................................................................................................... Slave Mode ....................................................................................................................................... Bus Collision Detection Function ..................................................................................................... Hardware LIN End Processing ......................................................................................................... Interrupt Requests .................................................................................................................................. Notes on Hardware LIN ........................................................................................................................ A-4 323 324 325 327 327 330 334 335 336 337 18. A/D Converter ............................................................................................................................. 338 18.1 18.2 18.3 18.4 18.5 18.6 18.7 19. One-Shot Mode ..................................................................................................................................... Repeat Mode .......................................................................................................................................... Sample and Hold ................................................................................................................................... A/D Conversion Cycles ......................................................................................................................... Internal Equivalent Circuit of Analog Input .......................................................................................... Output Impedance of Sensor under A/D Conversion ............................................................................ Notes on A/D Converter ........................................................................................................................ Flash Memory ............................................................................................................................. 352 19.1 19.2 19.3 19.3.1 19.3.2 19.4 19.4.1 19.4.2 19.4.3 19.4.4 19.4.5 19.5 19.5.1 19.6 19.6.1 19.7 19.7.1 20. 20.1 20.2 21. 342 345 348 348 349 350 351 Overview ............................................................................................................................................... Memory Map ......................................................................................................................................... Functions to Prevent Rewriting of Flash Memory ................................................................................ ID Code Check Function .................................................................................................................. ROM Code Protect Function ............................................................................................................ CPU Rewrite Mode ............................................................................................................................... EW0 Mode ........................................................................................................................................ EW1 Mode ........................................................................................................................................ Software Commands ......................................................................................................................... Status Registers ................................................................................................................................. Full Status Check .............................................................................................................................. Standard Serial I/O Mode ...................................................................................................................... ID Code Check Function .................................................................................................................. Parallel I/O Mode .................................................................................................................................. ROM Code Protect Function ............................................................................................................ Notes on Flash Memory ........................................................................................................................ CPU Rewrite Mode ........................................................................................................................... 352 353 355 355 356 357 358 358 367 372 373 375 375 378 378 379 379 Electrical Characteristics ............................................................................................................ 382 N, D Version .......................................................................................................................................... 382 J, K Version ........................................................................................................................................... 407 Usage Notes ............................................................................................................................... 427 21.1 Notes on Clock Generation Circuit ....................................................................................................... 427 21.1.1 Stop Mode ......................................................................................................................................... 427 21.1.2 Wait Mode ........................................................................................................................................ 427 21.1.3 Oscillation Stop Detection Function ................................................................................................. 427 21.1.4 Oscillation Circuit Constants ............................................................................................................ 427 21.2 Notes on Interrupts ................................................................................................................................ 428 21.2.1 Reading Address 00000h .................................................................................................................. 428 21.2.2 SP Setting .......................................................................................................................................... 428 21.2.3 External Interrupt and Key Input Interrupt ....................................................................................... 428 21.2.4 Changing Interrupt Sources .............................................................................................................. 429 21.2.5 Changing Interrupt Control Register Contents ................................................................................. 430 21.3 Notes on Timers .................................................................................................................................... 431 21.3.1 Notes on Timer RA ........................................................................................................................... 431 21.3.2 Notes on Timer RB ........................................................................................................................... 432 21.3.3 Notes on Timer RC ........................................................................................................................... 436 21.3.4 Notes on Timer RE ........................................................................................................................... 437 A-5 21.4 21.5 21.5.1 21.5.2 21.6 21.7 21.8 21.8.1 21.9 21.9.1 Notes on Serial Interface ....................................................................................................................... 440 Notes on Clock Synchronous Serial Interface ....................................................................................... 441 Notes on Clock Synchronous Serial I/O with Chip Select ............................................................... 441 Notes on I2C bus Interface ................................................................................................................ 441 Notes on Hardware LIN ........................................................................................................................ 442 Notes on A/D Converter ........................................................................................................................ 443 Notes on Flash Memory ........................................................................................................................ 444 CPU Rewrite Mode ........................................................................................................................... 444 Notes on Noise ...................................................................................................................................... 447 Inserting a Bypass Capacitor between VCC and VSS Pins as a Countermeasure against Noise and Latch-up ............................................................................................................................................ 447 21.9.2 Countermeasures against Noise Error of Port Control Registers ..................................................... 447 22. Notes for On-Chip Debugger ...................................................................................................... 448 Appendix 1. Package Dimensions ........................................................................................................ 449 Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator ............ 450 Appendix 3. Example of Oscillation Evaluation Circuit ......................................................................... 451 Index ..................................................................................................................................................... 452 A-6 SFR Page Reference Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh 002Ch 0030h 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah Register Symbol Page Processor Mode Register 0 Processor Mode Register 1 System Clock Control Register 0 System Clock Control Register 1 PM0 PM1 CM0 CM1 77 77 81 82 Protect Register PRCR 109 Oscillation Stop Detection Register Watchdog Timer Reset Register Watchdog Timer Start Register Watchdog Timer Control Register Address Match Interrupt Register 0 OCD WDTR WDTS WDC RMAD0 83 138 138 137 130 Address Match Interrupt Enable Register Address Match Interrupt Register 1 Count Source Protection Mode Register AIER RMAD1 CSPR 130 130 138 High-Speed On-Chip Oscillator Control Register 0 High-Speed On-Chip Oscillator Control Register 1 High-Speed On-Chip Oscillator Control Register 2 FRA0 84 FRA1 84 FRA2 85 Clock Prescaler Reset Flag High-Speed On-Chip Oscillator Control Register 4 CPSRF FRA4 86 85 High-Speed On-Chip Oscillator Control Register 6 High-Speed On-Chip Oscillator Control Register 7 FRA6 85 FRA7 85 Voltage Detection Register 1 Voltage Detection Register 2 VCA1 VCA2 39 39, 40, 86, 87 Voltage Monitor 1 Circuit Control Register Voltage Monitor 2 Circuit Control Register Voltage Monitor 0 Circuit Control Register VW1C VW2C VW0C 42, 43 44 41 003Bh 003Ch 003Dh 003Eh 003Fh Address 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh 005Fh 0060h 0061h 0062h 0063h 0064h 0065h 0066h 0067h 0068h 0069h 006Ah 006Bh 006Ch 006Dh 006Eh 006Fh 0070h 0071h 0072h 0073h 0074h 0075h 0076h 0077h 0078h 0079h 007Ah 007Bh 007Ch 007Dh 007Eh 007Fh NOTE: 1. The blank regions are reserved. Do not access locations in these regions. B-1 Register Symbol Page Timer RC Interrupt Control Register TRCIC 116 Timer RE Interrupt Control Register TREIC 115 Key Input Interrupt Control Register A/D Conversion Interrupt Control Register SSU/IIC bus Interrupt Control Register KUPIC ADIC SSUIC/IICIC 115 115 116 UART0 Transmit Interrupt Control Register UART0 Receive Interrupt Control Register UART1 Transmit Interrupt Control Register UART1 Receive Interrupt Control Register S0TIC S0RIC S1TIC S1RIC 115 115 115 115 Timer RA Interrupt Control Register TRAIC 115 Timer RB Interrupt Control Register INT1 Interrupt Control Register INT3 Interrupt Control Register TRBIC INT1IC INT3IC 115 117 117 INT0 Interrupt Control Register INT0IC 117 Address 0080h 0081h 0082h 0083h 0084h 0085h 0086h 0087h 0088h 0089h 008Ah 008Bh 008Ch 008Dh 008Eh 008Fh 0090h 0091h 0092h 0093h 0094h 0095h 0096h 0097h 0098h 0099h 009Ah 009Bh 009Ch 009Dh 009Eh 009Fh 00A0h 00A1h 00A2h 00A3h 00A4h 00A5h 00A6h 00A7h 00A8h 00A9h 00AAh 00ABh 00ACh 00ADh 00AEh 00AFh 00B0h 00B1h 00B2h 00B3h 00B4h 00B5h 00B6h 00B7h 00B8h 00B9h 00BAh 00BBh 00BCh 00BDh 00BEh 00BFh Register Symbol Page UART0 Transmit/Receive Mode Register UART0 Bit Rate Register UART0 Transmit Buffer Register U0MR U0BRG U0TB 244 244 243 UART0 Transmit/Receive Control Register 0 UART0 Transmit/Receive Control Register 1 UART0 Receive Buffer Register U0C0 U0C1 U0RB 245 246 243 UART1 Transmit/Receive Mode Register UART1 Bit Rate Register UART1 Transmit Buffer Register U1MR U1BRG U1TB 244 244 243 UART1 Transmit/Receive Control Register 0 UART1 Transmit/Receive Control Register 1 UART1 Receive Buffer Register U1C0 U1C1 U1RB 245 246 243 SS Control Register H / IIC bus Control Register 1 SS Control Register L / IIC bus Control Register 2 SS Mode Register / IIC bus Mode Register SS Enable Register / IIC bus Interrupt Enable Register SS Status Register / IIC bus Status Register SS Mode Register 2 / Slave Address Register SS Transmit Data Register / IIC bus Transmit Data Register SS Receive Data Register / IIC bus Receive Data Register SSCRH / ICCR1 SSCRL / ICCR2 SSMR / ICMR SSER / ICIER 262, 293 263, 294 264, 295 265, 296 SSSR / ICSR SSMR2 / SAR SSTDR / ICDRT 266, 297 267, 298 268, 298 Address 00C0h 00C1h 00C2h 00C3h 00C4h 00C5h 00C6h 00C7h 00C8h 00C9h 00CAh 00CBh 00CCh 00CDh 00CEh 00CFh 00D0h 00D1h 00D2h 00D3h 00D4h 00D5h 00D6h 00D7h 00D8h 00D9h 00DAh 00DBh 00DCh 00DDh 00DEh 00DFh 00E0h 00E1h 00E2h 00E3h 00E4h 00E5h 00E6h 00E7h 00E8h 00E9h 00EAh 00EBh 00ECh 00EDh 00EEh 00EFh 00F0h 00F1h 00F2h 00F3h 00F4h 00F5h 00F6h 00F7h 00F8h 00F9h 00FAh 00FBh 00FCh 00FDh 00FEh 00FFh SSRDR / ICDRR 268, 298 NOTE: 1. The blank regions are reserved. Do not access locations in these regions. B-2 A/D Register Register Symbol AD Page 341 A/D Control Register 2 ADCON2 341 A/D Control Register 0 A/D Control Register 1 ADCON0 ADCON1 340 341 Port P0 Register Port P1 Register Port P0 Direction Register Port P1 Direction Register P0 P1 PD0 PD1 61 61 60 60 Port P3 Register P3 61 Port P3 Direction Register Port P4 Register Port P5 Register Port P4 Direction Register Port P5 Direction Register PD3 P4 P5 PD4 PD5 60 61 61 60 60 Pin Select Register 1 Pin Select Register 2 Pin Select Register 3 Port Mode Register PINSR1 PINSR2 PINSR3 PMR External Input Enable Register INT Input Filter Select Register Key Input Enable Register Pull-Up Control Register 0 Pull-Up Control Register 1 Port P1 Drive Capacity Control Register INTEN INTF KIEN PUR0 PUR1 P1DRR 62, 247 62 62 63, 247, 269, 299 124 125 128 64 64 64 Address Register 0100h Timer RA Control Register 0101h Timer RA I/O Control Register 0102h 0103h 0104h 0105h 0106h 0107h 0108h 0109h 010Ah Symbol TRACR TRAIOC Page 144 144, 146, 149, 151, 153, 156 145 145 145 Timer RA Mode Register Timer RA Prescaler Register Timer RA Register TRAMR TRAPRE TRA LIN Control Register LIN Status Register Timer RB Control Register Timer RB One-Shot Control Register Timer RB I/O Control Register LINCR LINST TRBCR TRBOCR TRBIOC 010Bh 010Ch 010Dh 010Eh 010Fh 0110h 0111h 0112h 0113h 0114h 0115h 0116h 0117h Timer RB Mode Register Timer RB Prescaler Register Timer RB Secondary Register Timer RB Primary Register TRBMR TRBPRE TRBSC TRBPR 325 326 160 160 161, 163, 167, 170, 175 161 162 162 162 0118h Timer RE Second Data Register / Counter Data Register Timer RE Minute Data Register / Compare Data Register Timer RE Hour Data Register Timer RE Day of Week Data Register Timer RE Control Register 1 Timer RE Control Register 2 Timer RE Count Source Select Register TRESEC 226, 234 TREMIN 226, 234 TREHR TREWK TRECR1 TRECR2 TRECSR 227 227 228, 235 229, 235 230, 236 Timer RC Mode Register Timer RC Control Register 1 TRCMR TRCCR1 Timer RC Interrupt Enable Register Timer RC Status Register Timer RC I/O Control Register 0 Timer RC I/O Control Register 1 Timer RC Counter TRCIER TRCSR TRCIOR0 TRCIOR1 TRC 184 185, 208, 212, 217 186 187 192, 201, 206 192, 202, 207 188 Timer RC General Register A TRCGRA 188 Timer RC General Register B TRCGRB 188 Timer RC General Register C TRCGRC 188 Timer RC General Register D TRCGRD 188 0119h 011Ah 011Bh 011Ch 011Dh 011Eh 011Fh 0120h 0121h 0122h 0123h 0124h 0125h 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh Address Register 0130h Timer RC Control Register 2 0131h Timer RC Digital Filter Function Select Register 0132h Timer RC Output Master Enable Register 0133h 0134h 0135h 0136h 0137h 0138h 0139h 013Ah 013Bh 013Ch 013Dh 013Eh 013Fh 0140h 0141h 0142h 0143h 0144h 0145h 0146h 0147h 0148h 0149h 014Ah 014Bh 014Ch 014Dh 014Eh 014Fh 0150h 0151h 0152h 0153h 0154h 0155h 0156h 0157h 0158h 0159h 015Ah 015Bh 015Ch 015Dh 015Eh 015Fh 0160h 0161h 0162h 0163h 0164h 0165h 0166h 0167h 0168h 0169h 016Ah 016Bh 016Ch 016Dh 016Eh 016Fh NOTE: 1. The blank regions are reserved. Do not access locations in these regions. B-3 Symbol TRCCR2 TRCDF TRCOER Page 189 190 191 Address 0170h 0171h 0172h 0173h 0174h 0175h 0176h 0177h 0178h 0179h 017Ah 017Bh 017Ch 017Dh 017Eh 017Fh 0180h 0181h 0182h 0183h 0184h 0185h 0186h 0187h 0188h 0189h 018Ah 018Bh 018Ch 018Dh 018Eh 018Fh 0190h 0191h 0192h 0193h 0194h 0195h 0196h 0197h 0198h 0199h 019Ah 019Bh 019Ch 019Dh 019Eh 019Fh 01A0h 01A1h 01A2h 01A3h 01A4h 01A5h 01A6h 01A7h 01A8h 01A9h 01AAh 01ABh 01ACh 01ADh 01AEh 01AFh Register Symbol Page Address Register 01B0h 01B1h 01B2h 01B3h Flash Memory Control Register 4 01B4h 01B5h Flash Memory Control Register 1 01B6h 01B7h Flash Memory Control Register 0 01B8h 01B9h 01BAh 01BBh 01BCh 01BDh 01BEh FFFFh NOTE: 1. The blank regions are reserved. Do not access locations in these regions. B-4 Option Function Select Register Symbol Page FMR4 363 FMR1 362 FMR0 361 OFS 27, 137, 356 R8C/26 Group, R8C/27 Group SINGLE-CHIP 16-BIT CMOS MCU 1. REJ09B0278-0210 Rev.2.10 Sep 26, 2008 Overview These MCUs are fabricated using a high-performance silicon gate CMOS process, embedding the R8C CPU core, and are packaged in a 32-pin molded-plastic LQFP. It implements sophisticated instructions for a high level of instruction efficiency. With 1 Mbyte of address space, they are capable of executing instructions at high speed. Furthermore, the R8C/27 Group has on-chip data flash (1 KB x 2 blocks). The difference between the R8C/26 Group and R8C/27 Group is only the presence or absence of data flash. Their peripheral functions are the same. 1.1 Applications Electronic household appliances, office equipment, audio equipment, consumer products, automotive, etc. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 1 of 453 R8C/26 Group, R8C/27 Group 1.2 1. Overview Performance Overview Table 1.1 outlines the Functions and Specifications for R8C/26 Group and Table 1.2 outlines the Functions and Specifications for R8C/27 Group. Table 1.1 CPU Peripheral Functions Functions and Specifications for R8C/26 Group Item Number of fundamental instructions Minimum instruction execution time Operating mode Address space Memory capacity Ports LED drive ports Timers Serial interfaces Clock synchronous serial interface LIN module A/D converter Watchdog timer Interrupts Clock generation circuits Electrical Characteristics Oscillation-stopped detector Voltage detection circuit Power-on reset circuit Supply voltage Current consumption (N, D version) Flash Memory Programming and erasure voltage Programming and erasure endurance Operating Ambient Temperature Package Specification 89 instructions 50 ns (f(XIN) = 20 MHz, VCC = 3.0 to 5.5 V) (other than K version) 62.5 ns (f(XIN) = 16 MHz, VCC = 3.0 to 5.5 V) (K version) 100 ns (f(XIN) = 10 MHz, VCC = 2.7 to 5.5 V) 200 ns (f(XIN) = 5 MHz, VCC = 2.2 to 5.5 V) (N, D version) Single-chip 1 Mbyte Refer to Table 1.3 Product Information for R8C/26 Group I/O ports: 25 pins, Input port: 3 pins I/O ports: 8 pins (N, D version) Timer RA: 8 bits x 1 channel Timer RB: 8 bits x 1 channel (Each timer equipped with 8-bit prescaler) Timer RC: 16 bits x 1 channel (Input capture and output compare circuits) Timer RE: With real-time clock and compare match function (For J, K version, compare match function only.) 2 channels (UART0, UART1) Clock synchronous serial I/O, UART 1 channel I2C bus Interface(1) Clock synchronous serial I/O with chip select Hardware LIN: 1 channel (timer RA, UART0) 10-bit A/D converter: 1 circuit, 12 channels 15 bits x 1 channel (with prescaler) Start-on-reset selectable Internal: 15 sources, External: 4 sources, Software: 4 sources, Priority levels: 7 levels 3 circuits * XIN clock generation circuit (with on-chip feedback resistor) * On-chip oscillator (high speed, low speed) High-speed on-chip oscillator has a frequency adjustment function * XCIN clock generation circuit (32 kHz) (N, D version) * Real-time clock (timer RE) (N, D version) XIN clock oscillation stop detection function On-chip On-chip VCC = 3.0 to 5.5 V (f(XIN) = 20 MHz) (other than K version) VCC = 3.0 to 5.5 V (f(XIN) = 16 MHz) (K version) VCC = 2.7 to 5.5 V (f(XIN) = 10 MHz) VCC = 2.2 to 5.5 V (f(XIN) = 5 MHz) (N, D version) Typ. 10 mA (VCC = 5.0 V, f(XIN) = 20 MHz) Typ. 6 mA (VCC = 3.0 V, f(XIN) = 10 MHz) Typ. 2.0 A (VCC = 3.0 V, wait mode (f(XCIN) = 32 kHz) Typ. 0.7 A (VCC = 3.0 V, stop mode) VCC = 2.7 to 5.5 V 100 times -20 to 85C (N version) -40 to 85C (D, J version)(2), -40 to 125C (K version)(2) 32-pin molded-plastic LQFP NOTES: 1. I2C bus is a trademark of Koninklijke Philips Electronics N. V. 2. Specify the D, K version if D, K version functions are to be used. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 2 of 453 R8C/26 Group, R8C/27 Group Table 1.2 1. Overview Functions and Specifications for R8C/27 Group Item Specification Number of fundamental 89 instructions instructions Minimum instruction 50 ns (f(XIN) = 20 MHz, VCC = 3.0 to 5.5 V) (other than K version) execution time 62.5 ns (f(XIN) = 16 MHz, VCC = 3.0 to 5.5 V) (K version) 100 ns (f(XIN) = 10 MHz, VCC = 2.7 to 5.5 V) 200 ns (f(XIN) = 5 MHz, VCC = 2.2 to 5.5 V) (N, D version) Operating mode Single-chip Address space 1 Mbyte Memory capacity Refer to Table 1.4 Product Information of R8C/27 Group Peripheral Ports I/O ports: 25 pins, Input port: 3 pins Functions LED drive ports I/O ports: 8 pins (N, D version) Timers Timer RA: 8 bits x 1 channel Timer RB: 8 bits x 1 channel (Each timer equipped with 8-bit prescaler) Timer RC: 16 bits x 1 channel (Input capture and output compare circuits) Timer RE: With real-time clock and compare match function (For J, K version, compare match function only.) Serial interfaces 2 channels (UART0, UART1) Clock synchronous serial I/O, UART Clock synchronous 1 channel serial interface I2C bus Interface(1) Clock synchronous serial I/O with chip select LIN module Hardware LIN: 1 channel (timer RA, UART0) A/D converter 10-bit A/D converter: 1 circuit, 12 channels Watchdog timer 15 bits x 1 channel (with prescaler) Start-on-reset selectable Interrupts Internal: 15 sources, External: 4 sources, Software: 4 sources, Priority levels: 7 levels Clock generation 3 circuits circuits * XIN clock generation circuit (with on-chip feedback resistor) * On-chip oscillator (high speed, low speed) High-speed on-chip oscillator has a frequency adjustment function * XCIN clock generation circuit (32 kHz) (N, D version) * Real-time clock (timer RE) (N, D version) Oscillation-stopped XIN clock oscillation stop detection function detector Voltage detection circuit On-chip Power-on reset circuit On-chip Electrical Supply voltage VCC = 3.0 to 5.5 V (f(XIN) = 20 MHz) (other than K version) Characteristics VCC = 3.0 to 5.5 V (f(XIN) = 16 MHz) (K version) VCC = 2.7 to 5.5 V (f(XIN) = 10 MHz) VCC = 2.2 to 5.5 V (f(XIN) = 5 MHz) (N, D version) Current consumption Typ. 10 mA (VCC = 5.0 V, f(XIN) = 20 MHz) (N, D version) Typ. 6 mA (VCC = 3.0 V, f(XIN) = 10 MHz) Typ. 2.0 A (VCC = 3.0 V, wait mode (f(XCIN) = 32 kHz) Typ. 0.7 A (VCC = 3.0 V, stop mode) Flash Memory Programming and VCC = 2.7 to 5.5 V erasure voltage Programming and 10,000 times (data flash) erasure endurance 1,000 times (program ROM) Operating Ambient Temperature -20 to 85C (N version) -40 to 85C (D, J version)(2), -40 to 125C (K version)(2) Package 32-pin molded-plastic LQFP CPU NOTES: 1. I2C bus is a trademark of Koninklijke Philips Electronics N. V. 2. Specify the D, K version if D, K version functions are to be used. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 3 of 453 R8C/26 Group, R8C/27 Group 1.3 1. Overview Block Diagram Figure 1.1 shows a Block Diagram. I/O ports 8 8 6 Port P0 Port P1 Port P3 1 3 2 Port P4 Port P5 Peripheral functions System clock generation circuit A/D converter (10 bits x 12 channels) Timers Timer RA (8 bits) Timer RB (8 bits) Timer RC (16 bits x 1 channel) Timer RE (8 bits) XIN-XOUT High-speed on-chip oscillator Low-Speed on-chip oscillator XCIN-XCOUT(3) UART or clock synchronous serial I/O (8 bits x 2 channels) I2C bus interface or clock synchronous serial I/O with chip select (8 bits x 1 channel) LIN module (1 channel) Watchdog timer (15 bits) Memory R8C CPU core R0H R1H R0L R1L R2 R3 SB USP ISP INTB A0 A1 FB ROM(1) RAM(2) PC FLG Multiplier NOTES: 1. ROM size varies with MCU type. 2. RAM size varies with MCU type. 3. XCIN, XCOUT can be used only for N or D version. Figure 1.1 Block Diagram Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 4 of 453 R8C/26 Group, R8C/27 Group 1.4 1. Overview Product Information Table 1.3 lists the Product Information for R8C/26 Group and Table 1.4 lists the Product Information for R8C/27 Group. Table 1.3 Product Information for R8C/26 Group Part No. R5F21262SNFP R5F21264SNFP R5F21265SNFP R5F21266SNFP R5F21262SDFP R5F21264SDFP R5F21265SDFP R5F21266SDFP R5F21264JFP R5F21266JFP R5F21264KFP R5F21266KFP R5F21262SNXXXFP R5F21264SNXXXFP R5F21265SNXXXFP R5F21266SNXXXFP R5F21262SDXXXFP R5F21264SDXXXFP R5F21265SDXXXFP R5F21266SDXXXFP R5F21264JXXXFP R5F21266JXXXFP R5F21264KXXXFP R5F21266KXXXFP ROM Capacity 8 Kbytes 16 Kbytes 24 Kbytes 32 Kbytes 8 Kbytes 16 Kbytes 24 Kbytes 32 Kbytes 16 Kbytes 32 Kbytes 16 Kbytes 32 Kbytes 8 Kbytes 16 Kbytes 24 Kbytes 32 Kbytes 8 Kbytes 16 Kbytes 24 Kbytes 32 Kbytes 16 Kbytes 32 Kbytes 16 Kbytes 32 Kbytes RAM Capacity 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes NOTE: 1. The user ROM is programmed before shipment. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 5 of 453 Current of Sep. 2008 Package Type PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A Remarks N version D version J version K version N version D version J version K version Factory programming product(1) R8C/26 Group, R8C/27 Group Part No. 1. Overview R 5 F 21 26 6 S N XXX FP Package type: FP: PLQP0032GB-A ROM number Classification N: Operating ambient temperature -20 to 85C (N version) D: Operating ambient temperature -40 to 85C (D version) J: Operating ambient temperature -40 to 85C (J version) K: Operating ambient temperature -40 to 125C (K version) S: Low-voltage version (other no symbols) ROM capacity 2: 8 KB 4: 16 KB 5: 24 KB 6: 32 KB R8C/26 Group R8C/2x Series Memory type F: Flash memory Renesas MCU Renesas semiconductor Figure 1.2 Part Number, Memory Size, and Package of R8C/26 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 6 of 453 R8C/26 Group, R8C/27 Group Table 1.4 1. Overview Product Information for R8C/27 Group Part No. R5F21272SNFP R5F21274SNFP R5F21275SNFP R5F21276SNFP R5F21272SDFP R5F21274SDFP R5F21275SDFP R5F21276SDFP R5F21274JFP R5F21276JFP R5F21274KFP R5F21276KFP R5F21272SNXXXFP R5F21274SNXXXFP R5F21275SNXXXFP R5F21276SNXXXFP R5F21272SDXXXFP R5F21274SDXXXFP R5F21275SDXXXFP R5F21276SDXXXFP R5F21274JXXXFP R5F21276JXXXFP R5F21274KXXXFP R5F21276KXXXFP ROM Capacity Program Data flash ROM 8 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 24 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 8 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 24 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 8 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 24 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 8 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 24 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 16 Kbytes 1 Kbyte x 2 32 Kbytes 1 Kbyte x 2 NOTE: 1. The user ROM is programmed before shipment. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 7 of 453 Current of Sep. 2008 RAM Capacity Package Type 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 512 bytes 1 Kbyte 1.5 Kbytes 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A Remarks N version D version J version K version N version Factory programming product(1) D version J version K version R8C/26 Group, R8C/27 Group 1. Overview Part No. R 5 F 21 27 6 S N XXX FP Package type: FP: PLQP0032GB-A ROM number Classification N: Operating ambient temperature -20 to 85C (N version) D: Operating ambient temperature -40 to 85C (D version) J: Operating ambient temperature -40 to 85C (J version) K: Operating ambient temperature -40 to 125C (K version) S: Low-voltage version (other no symbols) ROM capacity 2: 8 KB 4: 16 KB 5: 24 KB 6: 32 KB R8C/27 Group R8C/2x Series Memory type F: Flash memory Renesas MCU Renesas semiconductor Figure 1.3 Part Number, Memory Size, and Package of R8C/27 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 8 of 453 R8C/26 Group, R8C/27 Group 1.5 1. Overview Pin Assignments P1_4/TXD0 P1_3/KI3/AN11/(TRBO) P1_1/KI1/AN9/TRCIOA/TRCTRG VREF/P4_2 P1_2/KI2/AN10/TRCIOB P1_0/KI0/AN8 P3_4/SDA/SCS/(TRCIOC)(2) P3_3/INT3/SSI/TRCCLK Figure 1.4 shows Pin Assignments (Top View). 24 23 22 21 20 19 18 17 16 26 15 27 14 R8C/26 Group R8C/27 Group 28 29 30 13 12 11 PLQP0032GB-A (32P6U-A) (top view) 2 P3_5/SCL/SSCK/(TRCIOD)(2) P3_7/TRAO/SSO/RXD1/(TXD1)(2) 1 3 4 5 6 10 9 7 8 MODE 32 VCC/AVCC 31 VSS/AVSS XIN/XCIN/P4_6 (3) P0_6/AN1 P0_5/AN2/CLK1 P0_4/AN3/TREO P0_3/AN4 P0_2/AN5 P0_1/AN6 P0_0/AN7/(TXD1)(2) 25 RESET XOUT/XCOUT/P4_7 (1, 3) P0_7/AN0 P1_5/RXD0/(TRAIO)/(INT1)(2) P1_6/CLK0/(SSI)(2) P5_3/TRCIOC P5_4/TRCIOD P3_1/TRBO P3_6/(TXD1)/(RXD1)/(INT1)(2) P1_7/TRAIO/INT1 P4_5/INT0/(RXD1)(2) NOTES: 1. P4_7 is an input-only port. 2. Can be assigned to the pin in parentheses by a program. 3. XCIN, XCOUT can be used only for N or D version. 4. Confirm the pin 1 position on the package by referring to the package dimensions. Figure 1.4 Pin Assignments (Top View) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 9 of 453 R8C/26 Group, R8C/27 Group 1.6 1. Overview Pin Functions Table 1.5 lists Pin Functions. Table 1.5 Pin Functions Type Symbol I/O Type Description Power supply input VCC, VSS I Apply 2.2 to 5.5 V (J, K version are 2.7 to 5.5 V) to the VCC pin. Apply 0 V to the VSS pin. Analog power supply input AVCC, AVSS I Power supply for the A/D converter. Connect a capacitor between AVCC and AVSS. Reset input RESET I Input "L" on this pin resets the MCU. MODE MODE I Connect this pin to VCC via a resistor. XIN clock input XIN I XIN clock output XOUT O These pins are provided for XIN clock generation circuit I/O. Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins. To use an external clock, input it to the XIN pin and leave the XOUT pin open. XCIN clock input (N, D version) XCIN I XCIN clock output (N, D version) XCOUT O INT interrupt input INT0, INT1, INT3 I INT interrupt input pins Key input interrupt KI0 to KI3 I Key input interrupt input pins Timer RA These pins are provided for XCIN clock generation circuit I/O. Connect a crystal oscillator between the XCIN and XCOUT pins. To use an external clock, input it to the XCIN pin and leave the XCOUT pin open. TRAO O Timer RA output pin TRAIO I/O Timer RA I/O pin Timer RB TRBO O Timer RB output pin Timer RC TRCCLK I External clock input pin TRCTRG Timer RE Serial interface I2C bus interface I External trigger input pin TRCIOA, TRCIOB, TRCIOC, TRCIOD I/O Sharing output-compare output / input-capture input / PWM / PWM2 output pins TREO O Timer RE output pin CLK0, CLK1 I/O RXD0, RXD1 I Receive data input pin TXD0, TXD1 O Transmit data output pin SCL I/O Clock I/O pin SDA I/O Data I/O pin Clock synchronous SSI serial I/O with chip SCS select SSCK Clock I/O pin I/O Data I/O pin I/O Chip-select signal I/O pin I/O Clock I/O pin SSO I/O Data I/O pin Reference voltage input VREF I Reference voltage input pin to A/D converter A/D converter AN0 to AN11 I Analog input pins to A/D converter I/O port P0_0 to P0_7, P1_0 to P1_7, P3_1, P3_3 to P3_7, P4_5, P5_3, P5_4 I/O Input port P4_2, P4_6, P4_7 I: Input O: Output Rev.2.10 Sep 26, 2008 REJ09B0278-0210 I I/O: Input and output Page 10 of 453 CMOS I/O ports. Each port has an I/O select direction register, allowing each pin in the port to be directed for input or output individually. Any port set to input can be set to use a pull-up resistor or not by a program. P1_0 to P1_7 also function as LED drive ports (N, D version). Input-only ports R8C/26 Group, R8C/27 Group Table 1.6 Pin Number 1. Overview Pin Name Information by Pin Number Control Pin Port 1 P3_5 2 P3_7 3 RESET 4 XOUT/XCOUT(2) VSS/AVSS P4_7 XIN/XCIN(2) VCC/AVCC MODE P4_6 5 6 7 8 9 10 11 P4_5 INT0 P1_7 INT1 P3_6 (INT1)(1) 12 13 14 15 P1_6 16 P1_5 17 18 P3_1 P5_4 P5_3 (RXD1)(1, 3) TRAIO (TXD1)/ (RXD1)(1, 3) TRBO TRCIOD TRCIOC CLK0 VRFF 22 (SSI)(1) (INT1)(1) (TRAIO)(1) P1_3 KI3 (TRBO) AN11 RXD0 P1_4 19 20 21 Interrupt I/O Pin Functions for of Peripheral Modules Clock A/D Serial Synchronous I2C bus Timer Interface Serial I/O with Interface Converter Chip Select (1) SSCK SCL (TRCIOD) RXD1/ TRAO SSO (TXD1)(1, 3) TXD0 P1_2 KI2 TRCIOB AN10 P4_2 P1_1 KI1 TRCIOA/ TRCTRG AN9 P1_0 KI0 23 P3_3 INT3 24 P3_4 25 26 27 28 29 30 31 32 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 AN8 TRCCLK SSI (TRCIOC)(1) SCS CLK1 TREO (TXD1)(1, 3) SDA AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 NOTES: 1. This can be assigned to the pin in parentheses by a program. 2. XCIN, XCOUT can be used only for N or D version. 3. For the combination of using pins TXD1 and RXD1, refer to Figure 15.7 Registers PINSR1 and PMR. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 11 of 453 R8C/26 Group, R8C/27 Group 2. 2. Central Processing Unit (CPU) Central Processing Unit (CPU) Figure 2.1 shows the CPU Registers. The CPU contains 13 registers. R0, R1, R2, R3, A0, A1, and FB configure a register bank. There are two sets of register bank. b31 b15 R2 R3 b8b7 b0 R0H (high-order of R0) R0L (low-order of R0) R1H (high-order of R1) R1L (low-order of R1) Data registers(1) R2 R3 A0 A1 FB b19 b15 Address registers(1) Frame base register(1) b0 Interrupt table register INTBL INTBH The 4 high order bits of INTB are INTBH and the 16 low order bits of INTB are INTBL. b19 b0 Program counter PC b15 b0 USP User stack pointer ISP Interrupt stack pointer SB Static base register b15 b0 FLG b15 b8 IPL b7 Flag register b0 U I O B S Z D C Carry flag Debug flag Zero flag Sign flag Register bank select flag Overflow flag Interrupt enable flag Stack pointer select flag Reserved bit Processor interrupt priority level Reserved bit NOTE: 1. These registers comprise a register bank. There are two register banks. Figure 2.1 CPU Registers Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 12 of 453 R8C/26 Group, R8C/27 Group 2.1 2. Central Processing Unit (CPU) Data Registers (R0, R1, R2, and R3) R0 is a 16-bit register for transfer, arithmetic, and logic operations. The same applies to R1 to R3. R0 can be split into high-order bits (R0H) and low-order bits (R0L) to be used separately as 8-bit data registers. R1H and R1L are analogous to R0H and R0L. R2 can be combined with R0 and used as a 32-bit data register (R2R0). R3R1 is analogous to R2R0. 2.2 Address Registers (A0 and A1) A0 is a 16-bit register for address register indirect addressing and address register relative addressing. It is also used for transfer, arithmetic, and logic operations. A1 is analogous to A0. A1 can be combined with A0 to be used as a 32-bit address register (A1A0). 2.3 Frame Base Register (FB) FB is a 16-bit register for FB relative addressing. 2.4 Interrupt Table Register (INTB) INTB is a 20-bit register that indicates the start address of an interrupt vector table. 2.5 Program Counter (PC) PC is 20 bits wide and indicates the address of the next instruction to be executed. 2.6 User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) The stack pointers (SP), USP, and ISP, are each 16 bits wide. The U flag of FLG is used to switch between USP and ISP. 2.7 Static Base Register (SB) SB is a 16-bit register for SB relative addressing. 2.8 Flag Register (FLG) FLG is an 11-bit register indicating the CPU state. 2.8.1 Carry Flag (C) The C flag retains carry, borrow, or shift-out bits that have been generated by the arithmetic and logic unit. 2.8.2 Debug Flag (D) The D flag is for debugging only. Set it to 0. 2.8.3 Zero Flag (Z) The Z flag is set to 1 when an arithmetic operation results in 0; otherwise to 0. 2.8.4 Sign Flag (S) The S flag is set to 1 when an arithmetic operation results in a negative value; otherwise to 0. 2.8.5 Register Bank Select Flag (B) Register bank 0 is selected when the B flag is 0. Register bank 1 is selected when this flag is set to 1. 2.8.6 Overflow Flag (O) The O flag is set to 1 when an operation results in an overflow; otherwise to 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 13 of 453 R8C/26 Group, R8C/27 Group 2.8.7 2. Central Processing Unit (CPU) Interrupt Enable Flag (I) The I flag enables maskable interrupts. Interrupt are disabled when the I flag is set to 0, and are enabled when the I flag is set to 1. The I flag is set to 0 when an interrupt request is acknowledged. 2.8.8 Stack Pointer Select Flag (U) ISP is selected when the U flag is set to 0; USP is selected when the U flag is set to 1. The U flag is set to 0 when a hardware interrupt request is acknowledged or the INT instruction of software interrupt numbers 0 to 31 is executed. 2.8.9 Processor Interrupt Priority Level (IPL) IPL is 3 bits wide and assigns processor interrupt priority levels from level 0 to level 7. If a requested interrupt has higher priority than IPL, the interrupt is enabled. 2.8.10 Reserved Bit If necessary, set to 0. When read, the content is undefined. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 14 of 453 R8C/26 Group, R8C/27 Group 3. 3. Memory Memory 3.1 R8C/26 Group Figure 3.1 is a Memory Map of R8C/26 Group. The R8C/26 group has 1 Mbyte of address space from addresses 00000h to FFFFFh. The internal ROM is allocated lower addresses, beginning with address 0FFFFh. For example, a 16-Kbyte internal ROM area is allocated addresses 0C000h to 0FFFFh. The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. They store the starting address of each interrupt routine. The internal RAM is allocated higher addresses beginning with address 00400h. For example, a 1-Kbyte internal RAM area is allocated addresses 00400h to 007FFh. The internal RAM is used not only for storing data but also for calling subroutines and as stacks when interrupt requests are acknowledged. Special function registers (SFRs) are allocated addresses 00000h to 002FFh. The peripheral function control registers are allocated here. All addresses within the SFR, which have nothing allocated are reserved for future use and cannot be accessed by users. 00000h 002FFh SFR (Refer to 4. Special Function Registers (SFRs)) 00400h Internal RAM 0XXXh 0FFDCh Undefined instruction Overflow BRK instruction Address match Single step Watchdog timer/oscillation stop detection/voltage monitor 0YYYYh (Reserved) (Reserved) Reset Internal ROM (program ROM) 0FFFFh 0FFFFh FFFFFh NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Internal ROM Part Number R5F21262SNFP, R5F21262SDFP, R5F21262SNXXXFP, R5F21262SDXXXFP Internal RAM Size Address 0YYYYh Size Address 0XXXXh 8 Kbytes 0E000h 512 bytes 005FFh 16 Kbytes 0C000h 1 Kbyte 007FFh 24 Kbytes 0A000h 1.5 Kbytes 009FFh 32 Kbytes 08000h 1.5 Kbytes 009FFh R5F21264SNFP, R5F21264SDFP, R5F21264JFP, R5F21264KFP, R5F21264SNXXXFP, R5F21264SDXXXFP, R5F21264JXXXFP, R5F21264KXXXFP R5F21265SNFP, R5F21265SDFP R5F21265SNXXXFP, R5F21265SDXXXFP R5F21266SNFP, R5F21266SDFP, R5F21266JFP, R5F21266KFP, R5F21266SNXXXFP, R5F21266SDXXXFP, R5F21266JXXXFP, R5F21266KXXXFP Figure 3.1 Memory Map of R8C/26 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 15 of 453 R8C/26 Group, R8C/27 Group 3.2 3. Memory R8C/27 Group Figure 3.2 is a Memory Map of R8C/27 Group. The R8C/27 group has 1 Mbyte of address space from addresses 00000h to FFFFFh. The internal ROM (program ROM) is allocated lower addresses, beginning with address 0FFFFh. For example, a 16-Kbyte internal ROM area is allocated addresses 0C000h to 0FFFFh. The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. They store the starting address of each interrupt routine. The internal ROM (data flash) is allocated addresses 02400h to 02BFFh. The internal RAM area is allocated higher addresses, beginning with address 00400h. For example, a 1-Kbyte internal RAM is allocated addresses 00400h to 007FFh. The internal RAM is used not only for storing data but also for calling subroutines and as stacks when interrupt requests are acknowledged. Special function registers (SFRs) are allocated addresses 00000h to 002FFh. The peripheral function control registers are allocated here. All addresses within the SFR, which have nothing allocated are reserved for future use and cannot be accessed by users. 00000h 002FFh SFR (Refer to 4. Special Function Registers (SFRs)) 00400h Internal RAM 0XXXXh 02400h 0FFDCh Internal ROM (data flash)(1) 02BFFh Undefined instruction Overflow BRK instruction Address match Single step 0YYYYh Watchdog timer/oscillation stop detection/voltage monitor (Reserved) (Reserved) Reset Internal ROM (program ROM) 0FFFFh 0FFFFh FFFFFh NOTES: 1. Data flash block A (1 Kbyte) and B (1 Kbyte) are shown. 2. The blank regions are reserved. Do not access locations in these regions. Internal ROM Part Number R5F21272SNFP, R5F21272SDFP, R5F21272SNXXXFP, R5F21272SDXXXFP R5F21274SNFP, R5F21274SDFP, R5F21274JFP, R5F21274KFP, R5F21274SNXXXFP, R5F21274SDXXXFP, Internal RAM Size Address 0YYYYh Size Address 0XXXXh 8 Kbytes 0E000h 512 bytes 005FFh 16 Kbytes 0C000h 1 Kbyte 007FFh 24 Kbytes 0A000h 1.5 Kbytes 009FFh 32 Kbytes 08000h 1.5 Kbytes 009FFh R5F21274JXXXFP, R5F21274KXXXFP R5F21275SNFP, R5F21275SDFP, R5F21275SNXXXFP, R5F21275SDXXXFP R5F21276SNFP, R5F21276SDFP, R5F21276JFP, R5F21276KFP, R5F21276SNXXXFP, R5F21276SDXXXFP, R5F21276JXXXFP, R5F21276KXXXFP Figure 3.2 Memory Map of R8C/27 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 16 of 453 R8C/26 Group, R8C/27 Group 4. 4. Special Function Registers (SFRs) Special Function Registers (SFRs) An SFR (special function register) is a control register for a peripheral function. Tables 4.1 to 4.7 list the special function registers. Table 4.1 Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh 002Ch 002Dh 002Eh 002Fh SFR Information (1)(1) Register Symbol After reset Processor Mode Register 0 Processor Mode Register 1 System Clock Control Register 0 System Clock Control Register 1 PM0 PM1 CM0 CM1 00h 00h 01101000b 00100000b Protect Register PRCR 00h Oscillation Stop Detection Register Watchdog Timer Reset Register Watchdog Timer Start Register Watchdog Timer Control Register Address Match Interrupt Register 0 OCD WDTR WDTS WDC RMAD0 Address Match Interrupt Enable Register Address Match Interrupt Register 1 AIER RMAD1 00000100b XXh XXh 00X11111b 00h 00h 00h 00h 00h 00h 00h Count Source Protection Mode Register CSPR 00h 10000000b(2) High-Speed On-Chip Oscillator Control Register 0 High-Speed On-Chip Oscillator Control Register 1 High-Speed On-Chip Oscillator Control Register 2 FRA0 FRA1 FRA2 00h When shipping 00h Clock Prescaler Reset Flag High-Speed On-Chip Oscillator Control Register 4(3) CPSRF FRA4 00h When shipping High-Speed On-Chip Oscillator Control Register 6(3) High-Speed On-Chip Oscillator Control Register 7(3) FRA6 FRA7 When shipping When shipping X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. The CSPROINI bit in the OFS register is set to 0. 3. In J, K version these regions are reserved. Do not access locations in these regions. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 17 of 453 R8C/26 Group, R8C/27 Group Table 4.2 Address 0030h 0031h 0032h 4. Special Function Registers (SFRs) SFR Information (2)(1) Register Symbol After reset Voltage Detection Register 1 (2) Voltage Detection Register 2 (2) VCA1 VCA2 00001000b 0033h 0034h 0035h 0036h Voltage Monitor 1 Circuit Control Register (5) VW1C 0037h 0038h Voltage Monitor 2 Circuit Control Register (5) Voltage Monitor 0 Circuit Control Register (6) VW2C VW0C Timer RC Interrupt Control Register TRCIC XXXXX000b Timer RE Interrupt Control Register TREIC XXXXX000b Key Input Interrupt Control Register A/D Conversion Interrupt Control Register SSU/IIC bus Interrupt Control Register(9) KUPIC ADIC SSUIC/IICIC XXXXX000b XXXXX000b XXXXX000b UART0 Transmit Interrupt Control Register UART0 Receive Interrupt Control Register UART1 Transmit Interrupt Control Register UART1 Receive Interrupt Control Register S0TIC S0RIC S1TIC S1RIC XXXXX000b XXXXX000b XXXXX000b XXXXX000b Timer RA Interrupt Control Register TRAIC XXXXX000b Timer RB Interrupt Control Register INT1 Interrupt Control Register INT3 Interrupt Control Register TRBIC INT1IC INT3IC XXXXX000b XX00X000b XX00X000b INT0 Interrupt Control Register INT0IC XX00X000b * N, D version 00h(3) 00100000b(4) * J, K version 00h(7) 01000000b(8) * N, D version 00001000b * J, K version 0000X000b(7) 0100X001b(8) 00h 0000X000b(3) 0100X001b(4) 0039h 003Fh 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh 005Fh 0060h 006Fh 0070h 007Fh X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. (N, D version) Software reset, watchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset do not affect this register. (J, K version) Software reset, watchdog timer reset, or voltage monitor 2 reset do not affect this register. 3. The LVD0ON bit in the OFS register is set to 1 and hardware reset. 4. Power-on reset, voltage monitor 0 reset or the LVD0ON bit in the OFS register is set to 0, and hardware reset. 5. (N, D version) Software reset, watchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset do not affect b2 and b3. (J, K version) Software reset, watchdog timer reset, or voltage monitor 2 reset do not affect b2 and b3. 6. (N, D version) Software reset, watchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset do not affect this register. (J, K version) These regions are reserved. Do not access locations in these regions. 7. The LVD1ON bit in the OFS register is set to 1 and hardware reset. 8. Power-on reset, voltage monitor 1 reset, or the LVD1ON bit in the OFS register is set to 0 and hardware reset. 9. Selected by the IICSEL bit in the PMR register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 18 of 453 R8C/26 Group, R8C/27 Group Table 4.3 Address 0080h 0081h 0082h 0083h 0084h 0085h 0086h 0087h 0088h 0089h 008Ah 008Bh 008Ch 008Dh 008Eh 008Fh 0090h 0091h 0092h 0093h 0094h 0095h 0096h 0097h 0098h 0099h 009Ah 009Bh 009Ch 009Dh 009Eh 009Fh 00A0h 00A1h 00A2h 00A3h 00A4h 00A5h 00A6h 00A7h 00A8h 00A9h 00AAh 00ABh 00ACh 00ADh 00AEh 00AFh 00B0h 00B1h 00B2h 00B3h 00B4h 00B5h 00B6h 00B7h 00B8h 00B9h 00BAh 00BBh 00BCh 00BDh 00BEh 00BFh 4. Special Function Registers (SFRs) SFR Information (3)(1) Register Symbol UART0 Transmit/Receive Mode Register UART0 Bit Rate Register UART0 Transmit Buffer Register U0MR U0BRG U0TB UART0 Transmit/Receive Control Register 0 UART0 Transmit/Receive Control Register 1 UART0 Receive Buffer Register U0C0 U0C1 U0RB UART1 Transmit/Receive Mode Register UART1 Bit Rate Register UART1 Transmit Buffer Register U1MR U1BRG U1TB UART1 Transmit/Receive Control Register 0 UART1 Transmit/Receive Control Register 1 UART1 Receive Buffer Register U1C0 U1C1 U1RB SS Control Register H / IIC bus Control Register 1(2) SS Control Register L / IIC bus Control Register 2(2) SS Mode Register / IIC bus Mode Register(2) SS Enable Register / IIC bus Interrupt Enable Register(2) SS Status Register / IIC bus Status Register(2) SS Mode Register 2 / Slave Address Register(2) SS Transmit Data Register / IIC bus Transmit Data Register(2) SS Receive Data Register / IIC bus Receive Data Register(2) SSCRH / ICCR1 SSCRL / ICCR2 SSMR / ICMR SSER / ICIER SSSR / ICSR SSMR2 / SAR SSTDR / ICDRT SSRDR / ICDRR X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. Selected by the IICSEL bit in the PMR register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 19 of 453 After reset 00h XXh XXh XXh 00001000b 00000010b XXh XXh 00h XXh XXh XXh 00001000b 00000010b XXh XXh 00h 01111101b 00011000b 00h 00h / 0000X000b 00h FFh FFh R8C/26 Group, R8C/27 Group Table 4.4 Address 00C0h 00C1h 00C2h 00C3h 00C4h 00C5h 00C6h 00C7h 00C8h 00C9h 00CAh 00CBh 00CCh 00CDh 00CEh 00CFh 00D0h 00D1h 00D2h 00D3h 00D4h 00D5h 00D6h 00D7h 00D8h 00D9h 00DAh 00DBh 00DCh 00DDh 00DEh 00DFh 00E0h 00E1h 00E2h 00E3h 00E4h 00E5h 00E6h 00E7h 00E8h 00E9h 00EAh 00EBh 00ECh 00EDh 00EEh 00EFh 00F0h 00F1h 00F2h 00F3h 00F4h 00F5h 00F6h 00F7h 00F8h 00F9h 00FAh 00FBh 00FCh 00FDh 00FEh 00FFh 4. Special Function Registers (SFRs) SFR Information (4)(1) Register Symbol After reset A/D Register AD XXh XXh A/D Control Register 2 ADCON2 00h A/D Control Register 0 A/D Control Register 1 ADCON0 ADCON1 00h 00h Port P0 Register Port P1 Register Port P0 Direction Register Port P1 Direction Register P0 P1 PD0 PD1 00h 00h 00h 00h Port P3 Register P3 00h Port P3 Direction Register Port P4 Register Port P5 Register Port P4 Direction Register Port P5 Direction Register PD3 P4 P5 PD4 PD5 00h 00h 00h 00h 00h Pin Select Register 1 Pin Select Register 2 Pin Select Register 3 Port Mode Register External Input Enable Register INT Input Filter Select Register Key Input Enable Register Pull-Up Control Register 0 Pull-Up Control Register 1 Port P1 Drive Capacity Control Register(2) PINSR1 PINSR2 PINSR3 PMR INTEN INTF KIEN PUR0 PUR1 P1DRR 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. In J, K version these regions are reserved. Do not access locations in these regions. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 20 of 453 R8C/26 Group, R8C/27 Group Table 4.5 Address 0100h 0101h 0102h 0103h 0104h 0105h 0106h 0107h 0108h 0109h 010Ah 010Bh 010Ch 010Dh 010Eh 010Fh 0110h 0111h 0112h 0113h 0114h 0115h 0116h 0117h 0118h 0119h 011Ah 011Bh 011Ch 011Dh 011Eh 011Fh 0120h 0121h 0122h 0123h 0124h 0125h 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh 0130h 0131h 0132h 0133h 0134h 0135h 0136h 0137h 0138h 0139h 013Ah 013Bh 013Ch 013Dh 013Eh 013Fh 4. Special Function Registers (SFRs) SFR Information (5)(1) Timer RA Control Register Timer RA I/O Control Register Timer RA Mode Register Timer RA Prescaler Register Timer RA Register Register Symbol TRACR TRAIOC TRAMR TRAPRE TRA 00h 00h 00h FFh FFh LIN Control Register LIN Status Register Timer RB Control Register Timer RB One-Shot Control Register Timer RB I/O Control Register Timer RB Mode Register Timer RB Prescaler Register Timer RB Secondary Register Timer RB Primary Register LINCR LINST TRBCR TRBOCR TRBIOC TRBMR TRBPRE TRBSC TRBPR 00h 00h 00h 00h 00h 00h FFh FFh FFh Timer RE Second Data Register / Counter Data Register Timer RE Minute Data Register / Compare Data Register Timer RE Hour Data Register(2) Timer RE Day of Week Data Register(2) Timer RE Control Register 1 Timer RE Control Register 2 Timer RE Count Source Select Register TRESEC TREMIN TREHR TREWK TRECR1 TRECR2 TRECSR 00h 00h 00h 00h 00h 00h 00001000b Timer RC Mode Register Timer RC Control Register 1 Timer RC Interrupt Enable Register Timer RC Status Register Timer RC I/O Control Register 0 Timer RC I/O Control Register 1 Timer RC Counter TRCMR TRCCR1 TRCIER TRCSR TRCIOR0 TRCIOR1 TRC Timer RC General Register A TRCGRA Timer RC General Register B TRCGRB Timer RC General Register C TRCGRC Timer RC General Register D TRCGRD Timer RC Control Register 2 Timer RC Digital Filter Function Select Register Timer RC Output Master Enable Register TRCCR2 TRCDF TRCOER 01001000b 00h 01110000b 01110000b 10001000b 10001000b 00h 00h FFh FFh FFh FFh FFh FFh FFh FFh 00011111b 00h 01111111b NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. In J, K version these regions are reserved. Do not access locations in these regions. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 21 of 453 After reset R8C/26 Group, R8C/27 Group Table 4.6 4. Special Function Registers (SFRs) SFR Information (6)(1) Address 0140h 0141h 0142h 0143h 0144h 0145h 0146h 0147h 0148h 0149h 014Ah 014Bh 014Ch 014Dh 014Eh 014Fh 0150h 0151h 0152h 0153h 0154h 0155h 0156h 0157h 0158h 0159h 015Ah 015Bh 015Ch 015Dh 015Eh 015Fh 0160h 0161h 0162h 0163h 0164h 0165h 0166h 0167h 0168h 0169h 016Ah 016Bh 016Ch 016Dh 016Eh 016Fh 0170h 0171h 0172h 0173h 0174h 0175h 0176h 0177h 0178h 0179h 017Ah 017Bh 017Ch 017Dh 017Eh 017Fh Register NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 22 of 453 Symbol After reset R8C/26 Group, R8C/27 Group Table 4.7 Address 0180h 0181h 0182h 0183h 0184h 0185h 0186h 0187h 0188h 0189h 018Ah 018Bh 018Ch 018Dh 018Eh 018Fh 0190h 0191h 0192h 0193h 0194h 0195h 0196h 0197h 0198h 0199h 019Ah 019Bh 019Ch 019Dh 019Eh 019Fh 01A0h 01A1h 01A2h 01A3h 01A4h 01A5h 01A6h 01A7h 01A8h 01A9h 01AAh 01ABh 01ACh 01ADh 01AEh 01AFh 01B0h 01B1h 01B2h 01B3h 01B4h 01B5h 01B6h 01B7h 01B8h 01B9h 01BAh 01BBh 01BCh 01BDh 01BEh 01BFh FFFFh 4. Special Function Registers (SFRs) SFR Information (7)(1) Register Symbol After reset Flash Memory Control Register 4 FMR4 01000000b Flash Memory Control Register 1 FMR1 1000000Xb Flash Memory Control Register 0 FMR0 00000001b Option Function Select Register OFS (Note 2) X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. The OFS register cannot be changed by a program. Use a flash programmer to write to it. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 23 of 453 R8C/26 Group, R8C/27 Group 5. 5. Resets Resets The following resets are implemented: hardware reset, power-on reset, voltage monitor 0 reset (for N, D version only), voltage monitor 1 reset, voltage monitor 2 reset, watchdog timer reset, and software reset. Table 5.1 lists the Reset Names and Sources. Figure 5.1 shows the Block Diagram of Reset Circuit (N, D Version), and Figure 5.2 shows the Block Diagram of Reset Circuit (J, K Version). Table 5.1 Reset Names and Sources Reset Name Source Hardware reset Power-on reset Input voltage of RESET pin is held "L" VCC rises VCC falls (monitor voltage: Vdet0) Voltage monitor 0 reset(1) Voltage monitor 1 reset Voltage monitor 2 reset Watchdog timer reset Software reset VCC falls (monitor voltage: Vdet1) VCC falls (monitor voltage: Vdet2) Underflow of watchdog timer Write 1 to PM03 bit in PM0 register NOTE: 1. For N, D version only. Hardware reset RESET SFRs Bits VCA25, VW0C0, and VW0C6 Power-on reset circuit VCC Power-on reset Voltage monitor 0 reset Voltage detection circuit Voltage monitor 1 reset Voltage monitor 2 reset Watchdog timer CPU SFRs Bits VCA13, VCA26, VCA27, VW1C2, VW1C3, VW2C2, VW2C3, VW0C1, VW0F0, VW0F1, and VW0C7 Watchdog timer reset Pin, CPU, and SFR bits other than those listed above Software reset VCA13: Bit in VCA1 register VCA25, VCA26, VCA27: Bits in VCA2 register VW0C0, VW0C1, VW0C6, VW0F0, VW0F1, VW0C7: Bits in VW0C register VW1C2, VW1C3: Bits in VW1C register VW2C2, VW2C3: Bits in VW2C register Figure 5.1 Block Diagram of Reset Circuit (N, D Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 24 of 453 R8C/26 Group, R8C/27 Group 5. Resets Hardware reset RESET SFRs Bits VCA26, VW1C0, and VW1C6 Power-on reset circuit VCC Power-on reset Voltage monitor 1 reset Voltage detection circuit Watchdog timer CPU Voltage monitor 2 reset SFR Bits VCA13, VCA27, VW2C2, VW2C3, VW1C1, VW1F0, VW1F1, and VW1C7 Watchdog timer reset Pin, CPU, and SFR bits other than those listed above Software reset VCA13: Bit in VCA1 register VCA26, VCA27: Bits in VCA2 register VW1C0, VW1C1, VW1F0, VW1F1, VW1C6, VW1C7: Bits in VW1C register VW2C2, VW2C3: Bits in VW2C register Figure 5.2 Block Diagram of Reset Circuit (J, K Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 25 of 453 R8C/26 Group, R8C/27 Group 5. Resets Table 5.2 shows the Pin Functions while RESET Pin Level is "L", Figure 5.3 shows the CPU Register Status after Reset, Figure 5.4 shows the Reset Sequence, and Figure 5.5 shows the OFS Register. Table 5.2 Pin Functions while RESET Pin Level is "L" Pin Name P0, P1 P3_1, P3_3 to P3_7 P4_2, P4_5 to P4_7 P5_3, P5_4 Pin Functions Input port Input port Input port Input port b15 b0 0000h Data register(R0) 0000h Data register(R1) 0000h Data register(R2) 0000h 0000h 0000h 0000h Data register(R3) b19 Address register(A0) Address register(A1) Frame base register(FB) b0 00000h Content of addresses 0FFFEh to 0FFFCh b15 Interrupt table register(INTB) Program counter(PC) b0 0000h User stack pointer(USP) 0000h Interrupt stack pointer(ISP) 0000h Static base register(SB) b15 b0 Flag register(FLG) 0000h b15 b8 IPL Figure 5.3 b0 b7 U I O B S Z D C CPU Register Status after Reset fOCO-S RESET pin 10 cycles or more are needed(1) fOCO-S clock x 32 cycles(2) Internal reset signal Start time of flash memory (CPU clock x 14 cycles) CPU clock x 28 cycles CPU clock 0FFFCh 0FFFEh Address (internal address signal) 0FFFDh Content of reset vector NOTES: 1. Hardware reset. 2. When the "L" input width to the RESET pin is set to fOCO-S clock x 32 cycles or more, setting the RESET pin to "H" also sets the internal reset signal to "H" at the same. Figure 5.4 Reset Sequence Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 26 of 453 R8C/26 Group, R8C/27 Group 5. Resets Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON LVD1ON Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2, 4) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset RW Voltage detection 1 circuit start bit(5, 6) 0 : Voltage monitor 1 reset enabled after hardw are reset 1 : Voltage monitor 1 reset disabled after hardw are reset RW Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. The LVD0ON bit setting is valid only by a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. 4. For N, D version only. For J, K version, set the LVD0ON bit to 1 (voltage monitor 0 reset disabled after hardw are reset). 5. The LVD1ON bit setting is valid only by a hardw are reset. When the pow er-on reset function is used, set the LVD1ON bit to 0 (voltage monitor 1 reset enabled after hardw are reset). 6. For J, K version only. For N, D version, set the LVD1ON bit to 1 (voltage monitor 1 reset disabled after hardw are reset). Figure 5.5 OFS Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 27 of 453 R8C/26 Group, R8C/27 Group 5.1 5. Resets Hardware Reset A reset is applied using the RESET pin. When an "L" signal is applied to the RESET pin while the supply voltage meets the recommended operating conditions, pins, CPU, and SFRs are all reset (refer to Table 5.2 Pin Functions while RESET Pin Level is "L"). When the input level applied to the RESET pin changes from "L" to "H", a program is executed beginning with the address indicated by the reset vector. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. Refer to 4. Special Function Registers (SFRs) for the state of the SFRs after reset. The internal RAM is not reset. If the RESET pin is pulled "L" while writing to the internal RAM is in progress, the contents of internal RAM will be undefined. Figure 5.6 shows an Example of Hardware Reset Circuit and Operation and Figure 5.7 shows an Example of Hardware Reset Circuit (Usage Example of External Supply Voltage Detection Circuit) and Operation. 5.1.1 When Power Supply is Stable (1) Apply "L" to the RESET pin. (2) Wait for 10 s or more. (3) Apply "H" to the RESET pin. 5.1.2 Power On (1) Apply "L" to the RESET pin. (2) Let the supply voltage increase until it meets the recommended operating conditions. (3) Wait for td(P-R) or more to allow the internal power supply to stabilize (refer to 20. Electrical Characteristics). (4) Wait for 10 s or more. (5) Apply "H" to the RESET pin. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 28 of 453 R8C/26 Group, R8C/27 Group 5. Resets VCC VCC 2.2 V (2.7 V for J, K version) 0V RESET RESET 0.2 VCC or below 0V td(P-R) + 10 s or more NOTE: 1. Refer to 20. Electrical Characteristics. Figure 5.6 Example of Hardware Reset Circuit and Operation Supply voltage detection circuit RESET 5V VCC VCC 2.2 V (2.7 V for J, K version) 0V 5V RESET 0V td(P-R) + 10 s or more Example when VCC = 5 V NOTE: 1. Refer to 20. Electrical Characteristics. Figure 5.7 Example of Hardware Reset Circuit (Usage Example of External Supply Voltage Detection Circuit) and Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 29 of 453 R8C/26 Group, R8C/27 Group 5.2 5. Resets Power-On Reset Function When the RESET pin is connected to the VCC pin via a pull-up resistor, and the VCC pin voltage level rises while the rise gradient is trth or more, the power-on reset function is enabled and the MCU resets its pins, CPU, and SFR. When a capacitor is connected to the RESET pin, too, always keep the voltage to the RESET pin 0.8VCC or more. When the input voltage to the VCC pin reaches theVdet0 (Vdet1 for J, K version) level or above, the low-speed onchip oscillator clock starts counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held "H" and the MCU enters the reset sequence (refer to Figure 5.4). The low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock after reset. Refer to 4. Special Function Registers (SFRs) for the states of the SFR after power-on reset. The voltage monitor 0 reset is enabled after power-on reset. Figure 5.8 and Figure 5.9 shows the Example of Power-On Reset Circuit and Operation. VCC 4.7 k (reference) RESET Vdet0(3) Vdet0(3) 2.2 V trth trth External Power VCC Vpor2 Vpor1 Sampling time(1, 2) tw(por1) Internal reset signal ("L" valid) 1 x 32 fOCO-S 1 x 32 fOCO-S NOTES: 1. When using the voltage monitor 0 digital filter, ensure that the voltage is within the MCU operation voltage range (2.2 V or above) during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection Circuit for details. 4. Refer to 20. Electrical Characteristics. 5. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. Figure 5.8 Example of Power-On Reset Circuit and Operation (N, D version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 30 of 453 R8C/26 Group, R8C/27 Group 5. Resets VCC 4.7 k (reference) RESET Vdet1(3) External power VCC Vdet1(3) trth trth 2.0 V td(Vdet1-A) Vpor2 Vpor1 tw(por1) Sampling time(1, 2) Internal reset signal ("L" valid) 1 x 32 fOCO-S 1 x 32 fOCO-S NOTES: 1. When using the voltage monitor 1 digital filter, ensure VCC is 2.0 V or higher during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. Vdet1 indicates the voltage detection level of the voltage detection 1 circuit. Refer to 6. Voltage Detection Circuit for details. 4. Refer to 20. Electrical Characteristics. 5. To use the power-on reset function, enable voltage monitor 1 reset by setting the LVD1ON bit in the OFS register to 0, the VW1C0 and VW1C6 bits in the VW1C register to 1 respectively, and the VCA26 bit in the VCA2 register to 1. Figure 5.9 Example of Power-On Reset Circuit and Operation (J, K version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 31 of 453 R8C/26 Group, R8C/27 Group 5.3 5. Resets Voltage Monitor 0 Reset (N, D Version) A reset is applied using the on-chip voltage detection 0 circuit. The voltage detection 0 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet0. When the input voltage to the VCC pin reaches the Vdet0 level or below, the pins, CPU, and SFR are reset. When the input voltage to the VCC pin reaches the Vdet0 level or above, the low-speed on-chip oscillator clock start counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held "H" and the MCU enters the reset sequence (refer to Figure 5.4). The low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock after reset. The LVD0ON bit in the OFS register can be used to enable or disable voltage monitor 0 reset after a hardware reset. Setting the LVD0ON bit is only valid after a hardware reset. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. The LVD0ON bit cannot be changed by a program. To set the LVD0ON bit, write 0 (voltage monitor 0 reset enabled after hardware reset) or 1 (voltage monitor 0 reset disabled after hardware reset) to bit 5 of address 0FFFFh using a flash programmer. Refer to Figure 5.5 OFS Register for details of the OFS register. Refer to 4. Special Function Registers (SFRs) for the status of the SFR after voltage monitor 0 reset. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet0 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 0 reset. 5.4 Voltage Monitor 1 Reset (N, D Version) A reset is applied using the on-chip voltage detection 1 circuit. The voltage detection 1 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet1. When the input voltage to the VCC pin drops the Vdet1 level or below, the pins, CPU, and SFR are reset and a program is executed beginning with the address indicated by the reset vector. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The voltage monitor 1 does not reset some portions of the SFR. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet1 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 1 reset. 5.5 Voltage Monitor 1 Reset (J, K Version) A reset is applied using the on-chip voltage detection 1 circuit. The voltage detection 1 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet1. When the input voltage to the VCC pin reaches the Vdet1 level or below, the pins, CPU, and SFR are reset. When the input voltage to the VCC pin reaches the Vdet1 level or above, the low-speed on-chip oscillator clock start counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held "H" and the MCU enters the reset sequence (refer to Figure 5.4). The low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock after reset. The LVD1ON bit in the OFS register can be used to enable or disable voltage monitor 1 reset. Setting the LVD1ON bit is only valid after a hardware reset. To use the power-on reset function, enable voltage monitor 1 reset by setting the LVD1ON bit in the OFS register to 0, the VW1C0 and VW1C6 bits in the VW1C register to 1 respectively, and the VCA26 bit in the VCA2 register to 1. The LVD1ON bit cannot be changed by a program. To set the LVD1ON bit, write 0 (voltage monitor 1 reset enabled after hardware reset) or 1 (voltage monitor 1 reset disabled after hardware reset) to bit 6 of address 0FFFFh using a flash programmer. Refer to Figure 5.5 OFS Register for details of the OFS register. Refer to 4. Special Function Registers (SFRs) for the status of the SFR after voltage monitor 1 reset. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet1 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 1 reset. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 32 of 453 R8C/26 Group, R8C/27 Group 5.6 5. Resets Voltage Monitor 2 Reset A reset is applied using the on-chip voltage detection 2 circuit. The voltage detection 2 circuit monitors the input voltage to the VCC pin. The voltage monitored is Vdet2. When the input voltage to the VCC pin drops the Vdet2 level or below, the pins, CPU, and SFR are reset and the program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The voltage monitor 2 does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet2 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 2 reset. 5.7 Watchdog Timer Reset When the PM12 bit in the PM1 register is set to 1 (reset when watchdog timer underflows), the MCU resets its pins, CPU, and SFR if the watchdog timer underflows. Then the program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The watchdog timer reset does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the watchdog timer underflows, the contents of internal RAM are undefined. Refer to 13. Watchdog Timer for details of the watchdog timer. 5.8 Software Reset When the PM03 bit in the PM0 register is set to 1 (MCU reset), the MCU resets its pins, CPU, and SFR. The program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected for the CPU clock. The software reset does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 33 of 453 R8C/26 Group, R8C/27 Group 6. 6. Voltage Detection Circuit Voltage Detection Circuit The voltage detection circuit monitors the input voltage to the VCC pin. This circuit can be used to monitor the VCC input voltage by a program. Alternately, voltage monitor 0 reset (for N, D version only), voltage monitor 1 interrupt (for N, D version only), voltage monitor 1 reset, voltage monitor 2 interrupt, and voltage monitor 2 reset can also be used. Table 6.1 lists the Specifications of Voltage Detection Circuit (N, D version) and Table 6.2 lists the Specifications of Voltage Detection Circuit (J, K Version). Figures 6.1 to 6.6 show the Block Diagrams. Figures 6.7 to 6.12 show the associated registers. Table 6.1 VCC Monitor Specifications of Voltage Detection Circuit (N, D version) Item Voltage to monitor Detection target Monitor Process Reset When Voltage is Detected Interrupt Digital Filter Switch enabled/disabled Sampling time Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Voltage Detection 0 Vdet0 Whether passing through Vdet0 by rising or falling None Voltage Detection 1 Voltage Detection 2 Vdet1 Vdet2 Passing through Vdet1 by Passing through Vdet2 by rising or falling rising or falling VW1C3 bit in VW1C register Whether VCC is higher or lower than Vdet1 Voltage monitor 0 reset Voltage monitor 1 reset Reset at Vdet0 > VCC; Reset at Vdet1 > VCC; restart CPU operation at restart CPU operation VCC > Vdet0 after a specified time None Voltage monitor 1 interrupt Interrupt request at Vdet1 > VCC and VCC > Vdet1 when digital filter is enabled; interrupt request at Vdet1 > VCC or VCC > Vdet1 when digital filter is disabled Available Available VCA13 bit in VCA1 register Whether VCC is higher or lower than Vdet2 Voltage monitor 2 reset Reset at Vdet2 > VCC; restart CPU operation after a specified time Voltage monitor 2 interrupt Interrupt request at Vdet2 > VCC and VCC > Vdet2 when digital filter is enabled; interrupt request at Vdet2 > VCC or VCC > Vdet2 when digital filter is disabled Available (Divide-by-n of fOCO-S) (Divide-by-n of fOCO-S) x4 x4 n: 1, 2, 4, and 8 n: 1, 2, 4, and 8 (Divide-by-n of fOCO-S) x4 n: 1, 2, 4, and 8 Page 34 of 453 R8C/26 Group, R8C/27 Group Table 6.2 VCC Monitor Specifications of Voltage Detection Circuit (J, K Version) Item Voltage to monitor Detection target Monitor Process Reset When Voltage is Detected Voltage Detection 1 Vdet1 Whether passing through Vdet1 by rising or falling None Voltage monitor 1 reset Reset at Vdet1 > VCC; restart CPU operation at VCC > Vdet1 None Interrupt Digital Filter 6. Voltage Detection Circuit Switch enabled/disabled Sampling time Voltage Detection 2 Vdet2 Passing through Vdet2 by rising or falling VCA13 bit in VCA1 register Whether VCC is higher or lower than Vdet2 Voltage monitor 2 reset Reset at Vdet2 > VCC; restart CPU operation after a specified time Available Voltage monitor 2 interrupt Interrupt request at Vdet2 > VCC and VCC > Vdet2 when digital filter is enabled; interrupt request at Vdet2 > VCC or VCC > Vdet2 when digital filter is disabled Available (Divide-by-n of fOCO-S) x 4 n: 1, 2, 4, and 8 (Divide-by-n of fOCO-S) x 4 n: 1, 2, 4, and 8 VCA27 VCC Noise filter + Internal reference voltage - Voltage detection 2 signal Vdet2 VCA1 register b3 VCA13 bit VCA26 Noise filter + - Vdet1 Voltage detection 1 signal VW1C register b3 VCA25 Voltage detection 0 signal + - Figure 6.1 Vdet0 Block Diagram of Voltage Detection Circuit (N, D version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 VW1C3 bit Page 35 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit VCA27 VCC - Voltage detection 2 signal Noise filter + Internal reference voltage Vdet2 VCA1 register b3 VCA26 VCA13 bit - Figure 6.2 Voltage detection 1 signal Noise filter + Vdet1 Block Diagram of Voltage Detection Circuit (J, K version) Voltage monitor 0 reset generation circuit VW0F1 to VW0F0 = 00b = 01b Voltage detection 0 circuit = 10b fOCO-S 1/2 1/2 1/2 = 11b VCA25 VW0C1 VCC Internal reference voltage + Digital filter Voltage detection 0 signal - Voltage detection 0 signal is held "H" when VCA25 bit is set to 0 (disabled) Voltage monitor 0 reset signal VW0C1 VW0C0 VW0C7 VW0C6 VW0C0 to VW0C1, VW0F0 to VW0F1, VW0C6, VW0C7: Bits in VW0C register VCA25: Bit in VCA2 register Figure 6.3 Block Diagram of Voltage Monitor 0 Reset Generation Circuit (For N, D Version Only) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 36 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage monitor 1 interrupt/reset generation circuit VW1F1 to VW1F0 = 00b = 01b Voltage detection 1 circuit VW1C2 bit is set to 0 (not detected) by writing 0 by a program. When VCA26 bit is set to 0 (voltage detection 1 circuit disabled), VW1C2 bit is set to 0 = 10b fOCO-S 1/2 1/2 1/2 = 11b VCA26 VW1C1 VW1C3 VCC + Noise filter Internal reference voltage (Filter width: 200 ns) Digital filter Voltage detection 1 signal Watchdog timer interrupt signal VW1C2 Voltage detection 1 signal is held "H" when VCA26 bit is set to 0 (disabled) Voltage monitor 1 interrupt signal Non-maskable interrupt signal VW1C1 Oscillation stop detection interrupt signal VW1C7 VW1C0 VW1C6 Voltage monitor 1 reset signal VW1C0 to VW1C3, VW1F0, VW1F1, VW1C6, VW1C7: Bits in VW1C register VCA26: Bit in VCA2 register Figure 6.4 Block Diagram of Voltage Monitor 1 Interrupt/Reset Generation Circuit (N, D version) Voltage monitor 1 interrupt/reset generation circuit VW1F1 to VW1F0 = 00b = 01b Voltage detection 1 circuit VW1C2 bit is set to 0 (not detected) by writing 0 by a program. When VCA26 bit is set to 0 (voltage detection 1 circuit disabled), VW1C2 bit is set to 0 = 10b fOCO-S 1/2 1/2 1/2 = 11b VCA26 VW1C1 VW1C3 VCC + Noise filter Internal reference voltage (Filter width: 200 ns) Digital filter Voltage detection 1 signal VW1C2 Voltage detection 1 signal is held "H" when VCA26 bit is set to 0 (disabled) VW1C1 VW1C7 VW1C0 VW1C6 Voltage monitor 1 reset signal VW1C0 to VW1C3, VW1F0, VW1F1, VW1C6, VW1C7: Bits in VW1C register VCA26: Bit in VCA2 register Figure 6.5 Block Diagram of Voltage Monitor 1 Reset Generation Circuit (J, K version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 37 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage monitor 2 interrupt/reset generation circuit VW2F1 to VW2F0 = 00b = 01b Voltage detection 2 circuit = 10b fOCO-S 1/2 1/2 1/2 VW2C2 bit is set to 0 (not detected) by writing 0 by a program. When VCA27 bit is set to 0 (voltage detection 2 circuit disabled), VW2C2 bit is set to 0 = 11b VCA27 VW2C1 VCA13 VCC + Noise filter Internal reference voltage (Filter width: 200 ns) Digital filter Voltage detection 2 signal Watchdog timer interrupt signal VW2C2 Voltage detection 2 signal is held "H" when VCA27 bit is set to 0 (disabled) Voltage monitor 2 interrupt signal Non-maskable interrupt signal VW2C1 Oscillation stop detection interrupt signal Watchdog timer block VW2C3 VW2C7 Watchdog timer underflow signal This bit is set to 0 (not detected) by writing 0 by a program. VW2C0 VW2C6 VW2C0 to VW2C3, VW2F0, VW2F1, VW2C6, VW2C7: Bits in VW2C register VCA13: Bit in VCA1 register VCA27: Bit in VCA2 register Figure 6.6 Block Diagram of Voltage Monitor 2 Interrupt/Reset Generation Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 38 of 453 Voltage monitor 2 reset signal R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Detection Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 After Reset(2) 00001000b Function Symbol Address 0031h VCA1 Bit Symbol Bit Name Reserved bits -- (b2-b0) VCA13 -- (b7-b4) Set to 0. Voltage detection 2 signal monitor flag(1) 0 : VCC < Vdet2 1 : VCC Vdet2 or voltage detection 2 circuit disabled Reserved bits Set to 0. RW RW RO RW NOTES: 1. The VCA13 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). The VCA13 bit is set to 1 (VCC Vdet 2) w hen the VCA27 bit in the VCA2 register is set to 0 (voltage detection 2 circuit disabled). 2. The softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. Voltage Detection Register 2(1) (N, D Version) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol VCA2 Bit Symbol VCA20 -- (b4-b1) Address 0032h Bit Name Internal pow er low consumption enable bit(6) After Reset(5) The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 00100000b Function 0 : Disables low consumption 1 : Enables low consumption RW RW Reserved bits Set to 0. VCA25 Voltage detection 0 enable bit(2) 0 : Voltage detection 0 circuit disabled 1 : Voltage detection 0 circuit enabled RW VCA26 Voltage detection 1 enable bit(3) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(4) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 0 reset, set the VCA25 bit to 1. After the VCA25 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 1 interrupt/reset or the VW1C3 bit in the VW1C register, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 5. Softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. 6. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.10 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 6.7 Registers VCA1 and VCA2 (N, D version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 39 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Detection Register 2(1) (J, K Version) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol VCA2 Bit Symbol VCA20 -- (b5-b1) Address 0032h Bit Name Internal pow er low consumption enable bit(5) After Reset(4) The LVD1ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 1 reset or LVD1ON bit in the OFS register is set to 0, and hardw are reset : 0100000b Function 0 : Disables low consumption 1 : Enables low consumption RW RW Reserved bits Set to 0. VCA26 Voltage detection 1 enable bit(2) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(3) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 1 reset, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. Softw are reset, w atchdog timer reset, or voltage monitor 2 reset do not affect this register. 5. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.10 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 6.8 VCA2 Register (J, K Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 40 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Monitor 0 Circuit Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol VW0C Bit Symbol VW0C0 VW0C1 VW0C2 -- (b3) 0038h Bit Name Voltage monitor 0 reset enable bit(3) Function 0 : Disable 1 : Enable Set to 0. Reserved bit When read, the content is undefined. Sampling clock select bits b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by RW RW Reserved bit VW0F1 VW0C7 The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 0000X000b Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 0100X001b Voltage monitor 0 digital filter 0 : Digital filter enabled mode disable mode select bit (digital filter circuit enabled) 1 : Digital filter disabled mode (digital filter circuit disabled) VW0F0 VW0C6 After Reset(2) Address RW RW 1 2 4 8 RO RW RW Voltage monitor 0 circuit mode select bit When the VW0C0 bit is set to 1 (voltage monitor 0 reset enabled), set to 1. RW Voltage monitor 0 reset generation condition select bit(4) When the VW0C1 bit is set to 1 (digital filter disabled mode), set to 1. RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VW0C register. 2. The value remains unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset. 3. The VW0C0 bit is enabled w hen the VCA25 bit in the VCA2 register is set to 1 (voltage detection 0 circuit enabled). Set the VW0C0 bit to 0 (disable), w hen the VCA25 bit is set to 0 (voltage detection 0 circuit disabled). 4. The VW0C7 bit is enabled w hen the VW0C1 bit set to 1 (digital filter disabled mode). Figure 6.9 VW0C Register (For N, D Version Only) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 41 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Monitor 1 Circuit Control Register(1) (N, D Version) b7 b6 b5 b4 b3 b2 b1 b0 Symbol VW1C Bit Symbol VW1C0 VW1C1 VW1C2 VW1C3 Address 0036h Bit Name Voltage monitor 1 interrupt/reset 0 : Disable enable bit(6) 1 : Enable RW 0 : Digital filter enabled mode (digital filter circuit enabled) 1 : Digital filter disabled mode (digital filter circuit disabled) RW Voltage change detection flag(3, 4, 8) 0 : Not detected 1 : Vdet1 pass detected RW Voltage detection 1 signal monitor flag(3, 8) 0 : VCC < Vdet1 1 : VCC Vdet1 or voltage detection 1 circuit disabled RO Sampling clock select bits b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by VW1F1 VW1C7 RW Voltage monitor 1 digital filter disable mode select bit(2) VW1F0 VW1C6 After Reset(8) 00001000b Function Voltage monitor 1 circuit mode select bit(5) 1 2 4 8 0 : Voltage monitor 1 interrupt mode 1 : Voltage monitor 1 reset mode Voltage monitor 1 interrupt/reset 0 : When VCC reaches Vdet1 or above generation condition select 1 : When VCC reaches Vdet1 or below bit(7,9) RW RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (rew rite enable) before w riting to the VW1C register. 2. To use the voltage monitor 1 interrupt to exit stop mode and to return again, w rite 0 to the VW1C1 bit before w riting 1. 3. Bits VW1C2 and VW1C3 are enabled w hen the VCA26 bit in the VCA2 register is set to 1 (voltage detection 1 circuit enabled). 4. Set this bit to 0 by a program. When 0 is w ritten by a program, it is set to 0 (and remains unchanged even if 1 is w ritten to it). 5. The VW1C6 bit is enabled w hen the VW1C0 bit is set to 1 (voltage monitor 1 interrupt/enabled reset). 6. The VW1C0 bit is enabled w hen the VCA26 bit in the VCA2 register is set to 1 (voltage detection 1 circuit enabled). Set the VW1C0 bit to 0 (disable) w hen the VCA26 bit is set to 0 (voltage detection 1 circuit disabled). 7. The VW1C7 bit is enabled w hen the VW1C1 bit is set to 1 (digital filter disabled mode). 8. Bits VW1C2 and VW1C3 remain unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset. 9. When the VW1C6 bit is set to 1 (voltage monitor 1 reset mode), set the VW1C7 bit to 1 (w hen VCC reaches Vdet1 or below ). (Do not set to 0.) Figure 6.10 VW1C Register (N, D Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 42 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Monitor 1 Circuit Control Register(1) (J, K Version) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol VW1C Bit Symbol VW1C0 VW1C1 Address 0036h Bit Name Voltage monitor 1 reset enable bit(4) After Reset(6) The LVD1ON bit in the OFS register is set to 1 and hardw are reset : 0000X000b Pow er-on reset, voltage monitor 1 reset or LVD1ON bit in the OFS register is set to 0, and hardw are reset : 0100X001b Function 0 : Disable 1 : Enable RW Voltage monitor 1 digital filter 0 : Digital filter enabled mode (digital filter circuit enabled) disable mode select bit(2) 1 : Digital filter disabled mode (digital filter circuit disabled) -- (b2) Reserved bit Set to 0. -- (b3) Reserved bit When read, the content is undefined. Sampling clock select bits b5 b4 VW1F0 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by VW1F1 VW1C6 VW1C7 RW RW RW 1 2 4 8 Voltage monitor 1 circuit mode select bit(3) When the VW1C0 bit is 1(voltage monitor 1 reset enabled), set to 1. Voltage monitor 1 reset generation condition select bit(5, 7) When the VW1C1 bit is 1(digital filter disabled mode), set to 1. RO RW RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (rew rite enable) before w riting to the VW1C register. 2. To use the voltage monitor 1 interrupt to exit stop mode and to return again, w rite 0 to the VW1C1 bit before w riting 1. 3. The VW1C6 bit is enabled w hen the VW1C0 bit is set to 1 (voltage monitor 1 reset enabled). 4. The VW1C0 bit is enabled w hen the VCA26 bit in the VCA2 register is set to 1 (voltage detection 1 circuit enabled). Set the VW1C0 bit to 0 (disable) w hen the VCA26 bit is set to 0 (voltage detection 1 circuit disabled). 5. The VW1C7 bit is enabled w hen the VW1C1 bit is set to 1 (digital filter disabled mode). 6. Softw are reset, w atchdog timer reset, or voltage monitor 2 reset do not affect this register. 7. When the VW1C6 bit is set to 1 (voltage monitor 1 reset mode), set the VW1C7 bit to 1 (w hen VCC reaches Vdet1 or below ). (Do not set to 0.) Figure 6.11 VW1C Register (J, K version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 43 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit Voltage Monitor 2 Circuit Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol VW2C Bit Symbol VW2C0 VW2C1 VW2C2 VW2C3 Address 0037h Bit Name Voltage monitor 2 interrupt/reset 0 : Disable 1 : Enable enable bit(6) RW 0 : Digital filter enabled mode (digital filter circuit enabled) 1 : Digital filter disabled mode (digital filter circuit disabled) RW Voltage change detection flag(3,4,8) 0 : Not detected 1 : VCC has crossed Vdet2 RW WDT detection flag(4,8) 0 : Not detected 1 : Detected RW Sampling clock select bits b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by VW2F1 VW2C7 RW Voltage monitor 2 digital filter disable mode select bit(2) VW2F0 VW2C6 After Reset(8) 00h Function Voltage monitor 2 circuit mode select bit(5) 1 2 4 8 0 : Voltage monitor 2 interrupt mode 1 : Voltage monitor 2 reset mode Voltage monitor 2 interrupt/reset 0 : When VCC reaches Vdet2 or above 1 : When VCC reaches Vdet2 or below generation condition select bit(7,9) RW RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VW2C register. 2. To use the voltage monitor 2 interrupt to exit stop mode and to return again, w rite 0 to the VW2C1 bit before w riting 1. 3. The VW2C2 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). 4. Set this bit to 0 by a program. When 0 is w ritten by a program, it is set to 0 (and remains unchanged even if 1 is w ritten to it). 5. The VW2C6 bit is enabled w hen the VW2C0 bit is set to 1 (voltage monitor 2 interrupt/enables reset). 6. The VW2C0 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). Set the VW2C0 bit to 0 (disable) w hen the VCA27 bit is set to 0 (voltage detection 2 circuit disabled). 7. The VW2C7 bit is enabled w hen the VW2C1 bit is set to 1 (digital filter disabled mode). 8. Bits VW2C2 and VW2C3 remain unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset (for N, D version only), or voltage monitor 2 reset. 9. When the VW2C6 bit is set to 1 (voltage monitor 2 reset mode), set the VW2C7 bit to 1 (w hen VCC reaches Vdet2 or below ). (Do not set to 0.) Figure 6.12 VW2C Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 44 of 453 R8C/26 Group, R8C/27 Group 6.1 6. Voltage Detection Circuit VCC Input Voltage 6.1.1 Monitoring Vdet0 Vdet0 cannot be monitored. 6.1.2 Monitoring Vdet1 Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled). After td(E-A) has elapsed (refer to 20. Electrical Characteristics), Vdet1 can be monitored by the VW1C3 bit in the VW1C register. 6.1.3 Monitoring Vdet2 Set the VCA27 bit in the VCA2 register to 1 (voltage detection 2 circuit enabled). After td(E-A) has elapsed (refer to 20. Electrical Characteristics), Vdet2 can be monitored by the VCA13 bit in the VCA1 register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 45 of 453 R8C/26 Group, R8C/27 Group 6.2 6. Voltage Detection Circuit Voltage Monitor 0 Reset (For N, D Version Only) Table 6.3 lists the Procedure for Setting Bits Associated with Voltage Monitor Reset and Figure 6.13 shows an Example of Voltage Monitor 0 Reset Operation. To use the voltage monitor 0 reset to exit stop mode, set the VW0C1 bit in the VW0C register to 1 (digital filter disabled). Table 6.3 Step 1 2 3 4(1) 5(1) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor Reset When Using Digital Filter When Not Using Digital Filter Set the VCA25 bit in the VCA2 register to 1 (voltage detection 0 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Set the VW0C7 bit in the VW0C register to by the VW0F0 to VW0F1 bits in the VW0C 1 register Set the VW0C1 bit in the VW0C register to Set the VW0C1 bit in the VW0C register to 0 (digital filter enabled) 1 (digital filter disabled) Set the VW0C6 bit in the VW0C register to 1 (voltage monitor 0 reset mode) Set the VW0C2 bit in the VW0C register to 0 Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of - (No wait time required) the digital filter Set the VW0C0 bit in the VW0C register to 1 (voltage monitor 0 reset enabled) NOTE: 1. When the VW0C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). VCC Vdet0 Sampling clock of digital filter x 4 cycles When the VW0C1 bit is set to 0 (digital filter enabled) 1 x 32 fOCO-S Internal reset signal 1 x 32 fOCO-S When the VW0C1 bit is set to 1 (digital filter disabled) and the VW0C7 bit is set to 1 Internal reset signal VW0C1 and VW0C7: Bits in VW0C register The above applies under the following conditions. * VCA25 bit in VCA2 register = 1 (voltage detection 0 circuit enabled) * VW0C0 bit in VW0C register = 1 (voltage monitor 0 reset enabled) * VW0C6 bit in VW0C register = 1 (voltage monitor 0 reset mode) When the internal reset signal is held "L", the pins, CPU and SFR are reset. The internal reset signal level changes from "L" to "H", and a program is executed beginning with the address indicated by the reset vector. Refer to 4. Special Function Registers (SFRs) for the SFR status after reset. Figure 6.13 Example of Voltage Monitor 0 Reset Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 46 of 453 R8C/26 Group, R8C/27 Group 6.3 6. Voltage Detection Circuit Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset (N, D Version) Table 6.4 lists the Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset. Figure 6.14 shows an Example of Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Operation (N, D Version). To use the voltage monitor 1 interrupt or voltage monitor 1 reset to exit stop mode, set the VW1C1 bit in the VW1C register to 1 (digital filter disabled). Table 6.4 Step 1 2 3 4(2) 5(2) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset When Using Digital Filter When Not Using Digital Filter Voltage Monitor 1 Voltage Monitor 1 Voltage Monitor 1 Voltage Monitor 1 Interrupt Reset Interrupt Reset Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Select the timing of the interrupt and reset request by the VW1C7 bit in the VW1C by the VW1F0 to VW1F1 bits in the VW1C register register(1) Set the VW1C1 bit in the VW1C register to 0 Set the VW1C1 bit in the VW1C register to 1 (digital filter enabled) (digital filter disabled) Set the VW1C6 bit in Set the VW1C6 bit in Set the VW1C6 bit in Set the VW1C6 bit in the VW1C register to the VW1C register to the VW1C register to the VW1C register to 0 (voltage monitor 1 1 (voltage monitor 1 0 (voltage monitor 1 1 (voltage monitor 1 reset mode) interrupt mode) reset mode) interrupt mode) Set the VW1C2 bit in the VW1C register to 0 (passing of Vdet1 is not detected) Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of the - (No wait time required) digital filter Set the VW1C0 bit in the VW1C register to 1 (voltage monitor 1 interrupt/reset enabled) NOTES: 1. Set the VW1C7 bit to 1 (when VCC reaches Vdet1 or below) for the voltage monitor 1 reset. 2. When the VW1C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 47 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit VCC Vdet1 2.2 V(1) 1 VW1C3 bit 0 4 cycles of sampling clock of digital filter 4 cycles of sampling clock of digital filter 1 VW1C2 bit 0 Set to 0 by a program When the VW1C1 bit is set to 0 (digital filter enabled) Set to 0 by interrupt request acknowledgement Voltage monitor 1 interrupt request (VW1C6 = 0) Internal reset signal (VW1C6 = 1) Set to 0 by a program 1 When the VW1C1 bit is set to 1 (digital filter disabled) and the VW1C7 bit is set to 0 (Vdet1 or above) VW1C2 bit 0 Set to 0 by interrupt request acknowledgement Voltage monitor 1 interrupt request (VW1C6 = 0) Set to 0 by a program 1 VW1C2 bit 0 When the VW1C1 bit is set to 1 (digital filter disabled) and the VW1C7 bit is set to 1 (Vdet1 or below) Voltage monitor 1 interrupt request (VW1C6 = 0) Set to 0 by interrupt request acknowledgement Internal reset signal (VW1C6 = 1) VW1C1, VW1C2, VW1C3, VW1C6, VW1C7: Bit in VW1C Register The above applies under the following conditions. * VCA26 bit in VCA2 register = 1 (voltage detection 1 circuit enabled) * VW1C0 bit in VW1C register = 1 (voltage monitor 1 interrupt and voltage monitor 1 reset enabled) NOTE: 1. If voltage monitor 0 reset is not used, set the power supply to VCC 2.2. Figure 6.14 Example of Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Operation (N, D Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 48 of 453 R8C/26 Group, R8C/27 Group 6.4 6. Voltage Detection Circuit Voltage Monitor 1 Reset (J, K Version) Table 6.5 lists the Procedure for Setting Bits Associated with Voltage Monitor 1 Reset. Figure 6.15 shows an Example of Voltage Monitor 1 Reset Operation (J, K Version). To use the voltage monitor 1 reset to exit stop mode, set the VW1C1 bit in the VW1C register to 1 (digital filter disabled). Table 6.5 Step 1 2 3 4(1) 5(1) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor 1 Reset When Using Digital Filter When Not Using Digital Filter Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Set the VW1C7 bit in the VW1C register to 1 by the VW1F0 to VW1F1 bits in the VW1C register Set the VW1C1 bit in the VW1C register to 0 Set the VW1C1 bit in the VW1C register to 1 (digital filter enabled) (digital filter disabled) Set the VW1C6 bit in the VW1C register to 1 (voltage monitor 1 reset mode) Set the VW1C2 bit in the VW1C register to 0 Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of the - (No wait time required) digital filter Set the VW1C0 bit in the VW1C register to 1 (voltage monitor 1 reset enabled) NOTE: 1. When the VW1C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). VCC Vdet1 Sampling clock of digital filter x 4 cycles When the VW1C1 bit is set to 0 (digital filter enabled) 1 x 32 fOCO-S Internal reset signal 1 x 32 fOCO-S When the VW1C1 bit is set to 1 (digital filter disabled) and the VW1C7 bit is set to 1 Internal reset signal VW1C1 and VW1C7: Bits in VW1C register The above applies under the following conditions. * VCA26 bit in VCA2 register = 1 (voltage detection 1 circuit enabled) * VW1C0 bit in VW1C register = 1 (voltage monitor 1 reset enabled) * VW1C6 bit in VW1C register = 1 (voltage monitor 1 reset mode) When the internal reset signal is held "L", the pins, CPU and SFR are reset. The internal reset signal level changes from "L" to "H", and a program is executed beginning with the address indicated by the reset vector. Refer to 4. Special Function Registers (SFRs) for the SFR status after reset. Figure 6.15 Example of Voltage Monitor 1 Reset Operation (J, K Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 49 of 453 R8C/26 Group, R8C/27 Group 6.5 6. Voltage Detection Circuit Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Table 6.6 lists the Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset. Figure 6.16 shows an Example of Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Operation. To use the voltage monitor 2 interrupt or voltage monitor 2 reset to exit stop mode, set the VW2C1 bit in the VW2C register to 1 (digital filter disabled). Table 6.6 Step 1 2 3 4 5(2) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset When Using Digital Filter When Not Using Digital Filter Voltage Monitor 2 Voltage Monitor 2 Voltage Monitor 2 Voltage Monitor 2 Interrupt Reset Interrupt Reset Set the VCA27 bit in the VCA2 register to 1 (voltage detection 2 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Select the timing of the interrupt and reset request by the VW2C7 bit in the VW2C by the VW2F0 to VW2F1 bits in the VW2C register register(1) Set the VW2C1 bit in the VW2C register to 0 Set the VW2C1 bit in the VW2C register to 1 (digital filter enabled) (digital filter disabled) Set the VW2C6 bit in Set the VW2C6 bit in Set the VW2C6 bit in Set the VW2C6 bit in the VW2C register to the VW2C register to the VW2C register to the VW2C register to 0 (voltage monitor 2 1 (voltage monitor 2 0 (voltage monitor 2 1 (voltage monitor 2 reset mode) interrupt mode) reset mode) interrupt mode) Set the VW2C2 bit in the VW2C register to 0 (passing of Vdet2 is not detected) Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of the - (No wait time required) digital filter Set the VW2C0 bit in the VW2C register to 1 (voltage monitor 2 interrupt/reset enabled) NOTES: 1. Set the VW2C7 bit to 1 (when VCC reaches Vdet2 or below) for the voltage monitor 2 reset. 2. When the VW2C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 50 of 453 R8C/26 Group, R8C/27 Group 6. Voltage Detection Circuit VCC Vdet2 2.2 V(1) 1 VCA13 bit 0 4 cycles of sampling clock of digital filter 4 cycles of sampling clock of digital filter 1 VW2C2 bit 0 Set to 0 by a program When the VW2C1 bit is set to 0 (digital filter enabled) Set to 0 by interrupt request acknowledgement Voltage monitor 2 interrupt request (VW2C6 = 0) Internal reset signal (VW2C6 = 1) Set to 0 by a program 1 When the VW2C1 bit is set to 1 (digital filter disabled) and the VW2C7 bit is set to 0 (Vdet2 or above) VW2C2 bit 0 Set to 0 by interrupt request acknowledgement Voltage monitor 2 interrupt request (VW2C6 = 0) Set to 0 by a program 1 VW2C2 bit 0 When the VW2C1 bit is set to 1 (digital filter disabled) and the VW2C7 bit is set to 1 (Vdet2 or below) Voltage monitor 2 interrupt request (VW2C6 = 0) Set to 0 by interrupt request acknowledgement Internal reset signal (VW2C6 = 1) VCA13: Bit in VCA1 register VW2C1, VW2C2, VW2C6, VW2C7: Bits in VW2C register The above applies under the following conditions. * VCA27 bit in VCA2 register = 1 (voltage detection 2 circuit enabled) * VW2C0 bit in VW2C register = 1 (voltage monitor 2 interrupt and voltage monitor 2 reset enabled) NOTE: 1. When voltage monitor 0 reset is not used, set the power supply to VCC 2.2. Figure 6.16 Example of Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 51 of 453 R8C/26 Group, R8C/27 Group 7. 7. Programmable I/O Ports Programmable I/O Ports There are 25 programmable Input/Output ports (I/O ports) P0, P1, P3_1, P3_3 to P3_7, P4_5, P5_3, and P5_4. Also, P4_6 and P4_7 can be used as input-only ports if the XIN clock oscillation circuit and XCIN clock oscillation circuit(1) is not used, and the P4_2 can be used as an input-only port if the A/D converter is not used. Table 7.1 lists an Overview of Programmable I/O Ports. NOTE: 1. The XCIN clock oscillation circuit cannot be used for J, K version. Table 7.1 Overview of Programmable I/O Ports Ports P0, P1 I/O I/O Type of Output CMOS3 State I/O Setting Set per bit Set every 4 bits(1) P3_1, P3_3 to P3_7 I/O CMOS3 State Set per bit Set every 2 bits, 4 bits(1) P4_5 I/O CMOS3 State Set per bit Set every bit(1) P5_3, P5_4 I/O CMOS3 State Set per bit Set every bit(1) (No output function) None None P4_2(2) P4_6, P4_7(3) I Internal Pull-Up Resister NOTES: 1. In input mode, whether an internal pull-up resistor is connected or not can be selected by registers PUR0 and PUR1. 2. When the A/D converter is not used, this port can be used as the input-only port. 3. When the XIN clock oscillation circuit and XCIN clock oscillation circuit (for N, D version only) is not used, these ports can be used as the input-only ports. 7.1 Functions of Programmable I/O Ports The PDi_j (j = 0 to 7) bit in the PDi (i = 0, 1, 3 to 5) register controls I/O of the ports P0, P1, P3_1, P3_3 to P3_7, P4_5, P5_3, and P5_4. The Pi register consists of a port latch to hold output data and a circuit to read pin states. Figures 7.1 to 7.6 show the Configurations of Programmable I/O Ports. Table 7.2 lists the Functions of Programmable I/O Ports. Also, Figure 7.8 shows the PDi (i = 0, 1, and 3 to 5) Register. Figure 7.9 shows the Pi (i = 0, 1, and 3 to 5) Register, Figure 7.10 shows Registers PINSR1, PINSR2, and PINSR3, Figure 7.11 shows the PMR Register, Figure 7.12 shows Registers PUR0 and PUR1, and Figure 7.13 shows the P1DRR Register. Table 7.2 Functions of Programmable I/O Ports Operation When Value of PDi_j Bit in PDi Register(1) Accessing When PDi_j Bit is Set to 0 (Input Mode) When PDi_j Bit is Set to 1 (Output Mode) Pi Register Reading Read pin input level Read the port latch Write to the port latch. The value written to Writing Write to the port latch the port latch is output from the pin. i = 0, 1, 3 to 5, j = 0 to 7 NOTE: 1. Nothing is assigned to bits PD3_0, PD3_2, PD4_0 to PD4_4, PD4_6, and PD4_7. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 52 of 453 R8C/26 Group, R8C/27 Group 7.2 7. Programmable I/O Ports Effect on Peripheral Functions Programmable I/O ports function as I/O ports for peripheral functions (refer to Table 1.6 Pin Name Information by Pin Number). Table 7.3 lists the Setting of PDi_j Bit when Functioning as I/O Ports for Peripheral Functions (i = 0, 1, 3 to 5, j = 0 to 7). Refer to the description of each function for information on how to set peripheral functions. Table 7.3 Setting of PDi_j Bit when Functioning as I/O Ports for Peripheral Functions (i = 0, 1, 3 to 5, j = 0 to 7) I/O of Peripheral Functions PDi_j Bit Settings for Shared Pin Functions Input Set this bit to 0 (input mode). Output This bit can be set to either 0 or 1 (output regardless of the port setting) 7.3 Pins Other than Programmable I/O Ports Figure 7.7 shows the Configuration of I/O Pins. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 53 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Pull-up selection P0 Direction register (Note 1) Data bus Port latch (Note 1) Analog input Drive capacity select (For N, D version only) P1_0 to P1_3 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Analog input Drive capacity select (For N, D version only) Drive capacity select (For N, D version only) P1_4 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Drive capacity select (For N, D version only) NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.1 Configuration of Programmable I/O Ports (1) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 54 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Drive capacity select (For N, D version only) P1_5 and P1_7 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Port latch Data bus (Note 1) Digital filter Input to external interrupt Input to individual peripheral function Drive capacity select (For N, D version only) Drive capacity select (For N, D version only) P1_6 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Port latch Data bus (Note 1) Input to individual peripheral function Drive capacity select (For N, D version only) NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.2 Configuration of Programmable I/O Ports (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 55 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports P3_1 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) P3_3 and P3_6 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Input to external interrupt P3_4, P3_5, and P3_7 Digital filter Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.3 Configuration of Programmable I/O Ports (3) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 56 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports (Note 1) P4_2/VREF Data bus (Note 1) P4_5 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Input to external interrupt Digital filter NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.4 Configuration of Programmable I/O Ports (4) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 57 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports (N, D Version) P4_6/XIN (Note 1) Data bus CM01 CM13 XIN oscillation circuit 0 1 (Note 1) XCIN oscillation circuit CM04 CM05 CM11 CM12 RfXIN RfXCIN P4_7/XOUT 0 1 (Note 2) (Note 1) CM01 Data bus (Note 1) (J, K Version) P4_6/XIN (Note 1) Data bus CM13 (Note 1) XIN oscillation circuit CM05 CM11 RfXIN P4_7/XOUT (Note 2) (Note 1) Data bus (Note 1) NOTES: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. 2. This pin is pulled up in one of the following conditions: * CM01 = CM05 = CM13 = 1 * CM01 = CM04 = 1 * CM01 = CM10 = CM13 = 1 * CM01 = CM10 = CM04 = 1 CM01, CM04, CM05: Bits in CM0 register CM10, CM13: Bits in CM1 register Figure 7.5 Configuration of Programmable I/O Ports (5) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 58 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports P5_3 and P5_4 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Port latch Data bus (Note 1) Input to individual peripheral function NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.6 Configuration of Programmable I/O Ports (5) MODE MODE signal input (Note 1) RESET RESET signal input (Note 1) NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.7 Configuration of I/O Pins Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 59 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Port Pi Direction Register (i = 0, 1, 3 to 5)(1, 2, 3, 4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PD0 PD1 PD3 PD4 PD5 Bit Symbol PDi_0 PDi_1 PDi_2 PDi_3 PDi_4 PDi_5 PDi_6 PDi_7 Address 00E2h 00E3h 00E7h 00EAh 00EBh Bit Name Port Pi_0 direction bit Port Pi_1 direction bit Port Pi_2 direction bit Port Pi_3 direction bit Port Pi_4 direction bit Port Pi_5 direction bit Port Pi_6 direction bit Port Pi_7 direction bit After Reset 00h 00h 00h 00h 00h Function 0 : Input mode (functions as an input port) 1 : Output mode (functions as an output port) RW RW RW RW RW RW RW RW RW NOTES: 1. Set the PD0 register by using the next instruction after setting the PRC2 bit in the PRCR register to 1 (w rite enable). 2. Bits PD3_0 and PD3_2 in the PD3 register are unavailable on this MCU. If it is necessary to set bits PD3_0 and PD3_2, set to 0 (input mode). When read, the content is 0. 3. Bits PD4_0 to PD4_4, PD4_6, and PD4_7 in the PD4 register are unavailable on this MCU. If it is necessary to set bits PD4_0 to PD4_4, PD4_6, and PD4_7, set to 0 (input mode). When read, the content is 0. 4. Bits PD5_0 to PD5_2 and PD5_5 to PD5_7 in the PD5 register are unavailable on this MCU. If it is necessary to set bits PD5_0 to PD5_2 and PD5_5 to PD5_7, set to 0 (input mode). When read, the content is 0. Figure 7.8 PDi (i = 0, 1, and 3 to 5) Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 60 of 453 R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Port Pi Register (i = 0, 1, 3 to 5)(1, 2, 3) b7 b6 b5 b4 b3 b2 b1 b0 Symbol P0 P1 P3 P4 P5 Bit Symbol Pi_0 Pi_1 Pi_2 Pi_3 Pi_4 Pi_5 Pi_6 Pi_7 Address 00E0h 00E1h 00E5h 00E8h 00E9h Bit Name Port Pi_0 bit Port Pi_1 bit Port Pi_2 bit Port Pi_3 bit Port Pi_4 bit Port Pi_5 bit Port Pi_6 bit Port Pi_7 bit After Reset 00h 00h 00h 00h 00h Function The pin level of any I/O port w hich is set to input mode can be read by reading the corresponding bit in this register. The pin level of any I/O port w hich is set to output mode can be controlled by w riting to the corresponding bit in this register. 0 : "L" level 1 : "H" level NOTES: 1. Bits P3_0 and P3_2 in the P3 register are unavailable on this MCU. If it is necessary to set bits P3_0 and P3_2, set to 0 ("L" level). When read, the content is 0. 2. Bits P4_0, P4_1, P4_3, and P4_4, in the P4 register are unavailable on this MCU. If it is necessary to set bits P4_0, P4_1, P4_3, and P4_4, set to 0 ("L" level). When read, the content is 0. 3. Bits P5_0 to P5_2, P5_5 to P5_7 in the P5 register are unavailable on this MCU. If it is necessary to set bits P5_0 to P5_2, P5_5 to P5_7, set to 0 ("L" level). When read, the content is 0. Figure 7.9 Pi (i = 0, 1, and 3 to 5) Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 61 of 453 RW RW RW RW RW RW RW RW RW R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Pin Select Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 1 Symbol PINSR1 Bit Symbol Address 00F5h Bit Name TXD1/RXD1 pin select bit(1) After Reset 00h Function RW b1 b0 0 0 : P3_7(TXD1/RXD1) 0 1 : P3_7(TXD1), P4_5(RXD1) 1 0 : P3_6(TXD1/RXD1) 1 1 : Do not set. UART1SEL0 UART1SEL1 -- (b2) Reserved bit Set to 1. When read, the content is 0. -- (b7-b3) Reserved bits Set to 0. When read, the content is 0. RW RW RW RW NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN in the PMR register. Refer to Figure 7.11 PMR Register. Pin Select Register 2 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 Symbol PINSR2 Bit Symbol -- (b5-b0) TRBOSEL -- (b7) Address 00F6h Bit Name Reserved bits After Reset 00h Function Set to 0. When read, the content is 0. TRBO pin select bit 0 : P3_1 1 : P1_3 Reserved bit Set to 0. When read, the content is 0. RW RW RW RW Pin Select Register 3 b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 1 Symbol PINSR3 Bit Symbol -- (b2-b0) TRCIOCSEL TRCIODSEL -- (b5) -- (b7-b6) Figure 7.10 Address 00F7h Bit Name Reserved bits After Reset 00h Function Set to 1. When read, the content is 0. TRCIOC pin select bit 0 : P5_3 1 : P3_4 RW TRCIOD pin select bit 0 : P5_4 1 : P3_5 RW Reserved bit Set to 1. When read, the content is 0. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Registers PINSR1, PINSR2, and PINSR3 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 62 of 453 RW RW RW -- R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Port Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol PMR Bit Symbol INT1SEL -- (b2-b1) SSISEL U1PINSEL TXD1SEL TXD1EN IICSEL Address 00F8h Bit Name _____ INT1 pin select bit After Reset 00h Function 0 : P1_5, P1_7 1 : P3_6 Nothing is assigned. If necessary, set to 0. When read, the content is 0. SSI pin select bit 0 : P3_3 1 : P1_6 RW TXD1 pin sw itch bit(1) 0 : P0_0 1 : P3_6, P3_7 RW Port/TXD1 pin sw itch bit(1) 0 : Programmable I/O port 1 : TXD1 RW TXD1/RXD1 select bit(1) 0 : RXD1 1 : TXD1 RW SSU / I2C bus pin sw itch bit 0 : Selects SSU function 1 : Selects I2C bus function RW Pin Function U1PINSEL bit PMR Register TXD1SEL bit x x 0 1 P3_7(TXD1) 00b P3_7(RXD1) P0_0(TXD1) 01b P3_7(TXD1) P4_5(RXD1) P3_6(TXD1) 10b P3_6(RXD1) P0_0(TXD1) x: 0 or 1 Figure 7.11 PMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW -- NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN, and bits UART1SEL1 and UART1SEL0 in the PINSR1 register. PINSR1 Register UART1SEL1, UART1SEL0 bit RW Page 63 of 453 1 1 x x x 0 1 TXD1EN bit 1 0 x x 1 0 x R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports Pull-Up Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol PUR0 Bit Symbol PU00 PU01 PU02 PU03 -- (b5-b4) Address 00FCh Bit Name P0_0 to P0_3 pull-up(1) P0_4 to P0_7 pull-up(1) P1_0 to P1_3 pull-up(1) P1_4 to P1_7 pull-up(1) Reserved bits After Reset 00h Function 0 : Not pulled up 1 : Pulled up PU06 PU07 P3_1 and P3_3 pull-up(1) P3_4 to P3_7 pull-up(1) 0 : Not pulled up 1 : Pulled up Set to 0. When read, the content is 0. RW RW RW RW RW RW RW RW NOTE: 1. When this bit is set to 1 (pulled up), the pin w hose direction bit is set to 0 (input mode) is pulled up. Pull-Up Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address 00FDh PUR1 Bit Symbol Bit Name -- Reserved bit (b0) After Reset 00h Function Set to 0. When read, the content is 0. PU11 PU12 PU13 -- (b5-b4) P4_5 pull-up(1) P5_3 pull-up(1) P5_4 pull-up(1) Reserved bits -- (b7-b6) Nothing is assigned. If necessary, set to 0. When read, the content is 0. 0 : Not pulled up 1 : Pulled up Set to 0. When read, the content is 0. RW RW RW RW RW RW -- NOTE: 1. When this bit is set to 1 (pulled up), the pin w hose direction bit is set to 0 (input mode) is pulled up. Figure 7.12 Registers PUR0 and PUR1 Port P1 Drive Capacity Control Register (For N, D Version Only) b7 b6 b5 b4 b3 b2 b1 b0 Symbol P1DRR Bit Symbol P1DRR0 P1DRR1 P1DRR2 P1DRR3 P1DRR4 P1DRR5 P1DRR6 P1DRR7 Address 00FEh Bit Name P1_0 drive capacity P1_1 drive capacity P1_2 drive capacity P1_3 drive capacity P1_4 drive capacity P1_5 drive capacity P1_6 drive capacity P1_7 drive capacity NOTE: 1. Both "H" and "L" output are set to high drive capacity. Figure 7.13 P1DRR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 64 of 453 After Reset 00h Function Set P1 output transistor drive capacity 0 : Low 1 : High(1) RW RW RW RW RW RW RW RW RW R8C/26 Group, R8C/27 Group 7.4 7. Programmable I/O Ports Port Setting Table 7.4 to Table 7.40 list the port setting. Table 7.4 Port P0_0/AN7/(TXD1) Register PD0 Bit PD0_0 Setting value U1MR SMD2 ADCON0 SMD1 SMD0 CH2 CH1 CH0 Function ADGSEL0 0 X X X X X X X Input port(1, 2) 1 X X X X X X X Output port(1) 0 X X X 1 1 1 0 A/D converter input (AN7)(1) 0 0 X X X X TXD1 output(3, 4) 0 X 1 1 1 1 0 X: 0 or 1 NOTES: 1. When the U1PINSEL bit is set to 0 (P0_0) and TXD1SEL bit is set to 1 (TXD1) in the PMR register, set bits SMD2 to SMD0 in the U1MR register to 000b (serial interface disabled). 2. Pulled up by setting the PU00 bit in the PUR0 register to 1. 3. This is enabled when bits UART1SEL1 and UART1SEL0 in the PINSR1 register are set to 00b or 10b, and the U1PINSEL bit is set to 0 (P0_0) and TXD1SEL bit is set to 1 (TXD1) in the PMR register. 4. N-channel open drain output by setting the NCH bit in the U1C0 register to 1. Table 7.5 Port P0_1/AN6 Register PD0 Bit PD0_1 ADCON0 Setting value 0 X X X X Input port(1) 1 X X X X Output port 0 1 1 0 0 A/D converter input (AN6) CH2 CH1 CH0 Function ADGSEL0 X: 0 or 1 NOTE: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. Table 7.6 Port P0_2/AN5 Register PD0 Bit PD0_2 CH2 CH1 CH0 ADGSEL0 0 X X X X 1 X X X X Output port 0 1 0 1 0 A/D converter input (AN5) Setting value ADCON0 Function Input port(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. Table 7.7 Port P0_3/AN4 Register PD0 Bit PD0_3 CH2 CH1 CH0 ADGSEL0 0 X X X X 1 X X X X Output port 0 1 0 0 0 A/D converter input (AN4) Setting value ADCON0 X: 0 or 1 NOTE: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 65 of 453 Function Input port(1) R8C/26 Group, R8C/27 Group Table 7.8 7. Programmable I/O Ports Port P0_4/AN3/TREO Register PD0 TRECR1 Bit PD0_4 TOENA CH2 CH1 CH0 ADGSEL0 0 0 X X X X 1 0 X X X X Output port 0 0 0 1 1 0 A/D converter input (AN3) X 1 X X X X TREO output Setting value ADCON0 Function Input port(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU01 bit in the PUR0 register to 1. Table 7.9 Port P0_5/AN2/CLK1 Register PD0 Bit PD0_5 U1MR SMD2 ADCON0 SMD0 CKDIR Other than 001b 0 Setting value SMD1 X X X CH2 CH1 CH0 Function ADGSEL0 X X X X X 1 X X X X Input port(1) 1 Other than 001b X X X X X Output port 0 Other than 001b X 0 1 0 0 A/D converter input (AN2) X 0 0 1 0 X X X X CLK1 output 0 X X X 1 X X X X CLK1 input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU01 bit in the PUR0 register to 1. Table 7.10 Port P0_6/AN1 Register PD0 Bit PD0_6 ADCON0 Setting value 0 X X X X Input port(1) 1 X X X X Output port 0 0 0 1 0 A/D converter input (AN1) CH2 CH1 CH0 Function ADGSEL0 X: 0 or 1 NOTE: 1. Pulled up by setting the PU01 bit in the PUR0 register to 1. Table 7.11 Port P0_7/AN0 Register PD0 Bit PD0_7 CH2 CH1 CH0 ADGSEL0 0 X X X X 1 X X X X Output port 0 0 0 0 0 A/D converter input (AN0) Setting value ADCON0 Function Input port(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU01 bit in the PUR0 register to 1. Table 7.12 Port P1_0/KI0/AN8 Register PD1 KIEN Bit PD1_0 KI0EN CH2 CH1 CH0 ADGSEL0 0 0 X X X X Input port(1) Setting value ADCON0 Function 1 0 X X X X Output port 0 1 X X X X KI0 input(1) 0 0 1 0 0 1 A/D converter input (AN8) X: 0 or 1 NOTE: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 66 of 453 R8C/26 Group, R8C/27 Group Table 7.13 Register Bit Setting value 7. Programmable I/O Ports Port P1_1/KI1/AN9/TRCIOA/TRCTRG PD1 KIEN Timer RC Setting PD1_1 KI1EN ADCON0 - CH2 CH1 CH0 ADGSEL0 Function 0 0 Other than TRCIOA usage conditions X X X X Input port(1) 1 0 Other than TRCIOA usage conditions X X X X Output port 0 0 Other than TRCIOA usage conditions 1 0 1 1 A/D converter input (AN9) 0 1 Other than TRCIOA usage conditions X X X X KI1 input(1) X 0 Refer to Table 7.14 TRCIOA Pin Setting X X X X TRCIOA output 0 0 Refer to Table 7.14 TRCIOA Pin Setting X X X X TRCIOA input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. Table 7.14 TRCIOA Pin Setting Register TRCOER TRCMR Bit EA PWM2 0 1 0 Setting value 1 1 TRCIOR0 IOA2 IOA1 0 0 1 0 TRCCR2 IOA0 TCEG1 TCEG0 0 1 X X 1 X X X 1 X X X X X X X X X 0 1 1 X Function Timer waveform output (output compare function) Timer mode (input capture function) PWM2 mode TRCTRG input Other than above Other than TRCIOA usage conditions X: 0 or 1 Table 7.15 Register Bit Setting value Port P1_2/KI2/AN10/TRCIOB PD1 KIEN Timer RC Setting PD1_2 KI2EN ADCON0 - CH2 CH1 CH0 ADGSEL0 Function 0 0 Other than TRCIOB usage conditions X X X X Input port(1) 1 0 Other than TRCIOB usage conditions X X X X Output port 0 0 Other than TRCIOB usage conditions 1 1 0 1 A/D converter input (AN10) 0 1 Other than TRCIOB usage conditions X X X X KI2 input(1) X 0 Refer to Table 7.16 TRCIOB Pin Setting X X X X TRCIOB output 0 0 Refer to Table 7.16 TRCIOB Pin Setting X X X X TRCIOB input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. Table 7.16 TRCIOB Pin Setting Register TRCOER Bit EB Setting value TRCMR TRCIOR0 PWMB 0 0 X X X X PWM2 mode waveform output 0 1 1 X X X PWM mode waveform output 0 1 0 0 0 1 0 1 X Timer waveform output (output compare function) 1 0 1 X X Timer mode (input capture function) 0 1 IOB2 Other than above X: 0 or 1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 67 of 453 IOB1 IOB0 Function PWM2 Other than TRCIOB usage conditions R8C/26 Group, R8C/27 Group Table 7.17 7. Programmable I/O Ports Port P1_3/KI3/AN11/(TRBO) Register PD1 KIEN Timer RB Setting Bit PD1_3 KI3EN - CH2 CH1 CH0 ADGSEL0 0 0 Other than TRBO usage conditions X X X X Input port(1) Setting value ADCON0 Function 1 0 Other than TRBO usage conditions X X X X Output port 0 0 Other than TRBO usage conditions 1 1 1 1 A/D converter input (AN11) 0 1 Other than TRBO usage conditions X X X X KI3 input 0 Refer to Table 7.18 TRBO Pin Setting X X X X TRBO output X X: 0 or 1 NOTE: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. Table 7.18 TRBO Pin Setting Register PINSR2 TRBIOC Bit TRBOSEL TOCNT(1) Setting value TRBMR TMOD1 Function TMOD0 1 0 0 1 Programmable waveform generation mode 1 0 1 0 Programmable one-shot generation mode 1 0 1 1 Programmable wait one-shot generation mode 1 1 0 1 P1_3 output port Other than above Other than TRBO usage conditions NOTE: 1. Set the TOCNT bit in the TRBIOC register to 0 in modes except for programmable waveform generation mode. Table 7.19 Port P1_4/TXD0 Register PD1 Bit PD1_4 SMD2 SMD1 SMD0 0 0 0 0 Input port(1) 1 0 0 0 Output port 0 0 1 1 0 0 1 0 1 1 1 0 Setting value X U0MR X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. N-channel open drain output by setting the NCH bit in the U0C0 register to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 68 of 453 Function TXD0 output(2) R8C/26 Group, R8C/27 Group Table 7.20 Register Bit 7. Programmable I/O Ports Port P1_5/RXD0/(TRAIO)/(INT1) PD1 TRAIOC PD1_5 TIOSEL 0 0 1 1 Setting value 0 X TRAMR TOPCR(3 INTEN TMOD2 TMOD1 TMOD0 INT1EN X X X X X 1 0 0 1 0 ) 1 0 0 0 0 0 0 X X X X X 1 0 0 0 0 X 0 X X X X X 1 0 Other than 001b 0 1 0 Other than 000b, 001b 0 1 0 0 0 0 1 1 1 0 0 1 1 1 0 1 0 Other than 000b, 001b 0 0 1 Function Input port(1) Output port RXD0 input(1) TRAIO input(1) INT1(2) 1 TRAIO input/INT1(1, 2) X TRAIO pulse output X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. Set the INT1SEL bit in the PMR register to 0 (P1_5, P1_7). 3. Set the TOPCR bit in the TRAIOC register to 0 in modes except for pulse output mode. Table 7.21 Register Bit Setting value Port P1_6/CLK0/(SSI) PD1 U0MR PD1_6 CKDIR 0 X 1 X Clock Synchronous Serial I/O with Chip Select (Refer to Table 16.4 Association between Communication Modes and I/O Pins.) PMR Function(3) SMD2 SMD1 SMD0 IICSEL SSI output control X X X X 0 0 Input port(1) X 0 0 Output port Other than 001b SSI input control X 0 0 0 1 X 0 0 CLK0 output 0 1 X X X X 0 0 CLK0 input(1) X X X X X 0 1 0 SSI output(2) X X X X X 0 0 1 SSI input(1, 2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. Set the SSISEL bit in the PMR register to 1 (P1_6). 3. When the SOOS bit is set to 1 (N-channel open drain output) and BIDE bit is set to 0 (standard mode) in the SSMR2 register, this pin is set to N-channel open drain output. Table 7.22 Port P1_7/TRAIO/INT1 Register PD1 Bit PD1_7 TRAIOC TRAMR INTEN TIOSEL TOPCR(3) TMOD2 TMOD1 TMOD0 INT1EN 1 X X X X X 0 1 0 0 1 0 0 0 0 0 0 0 1 X X X X X 0 0 0 0 0 X 0 0 0 0 0 0 0 1 0 1 0 0 1 1 0 0 0 0 0 1 Setting value 0 X Other than 000b, 001b Other than 000b, 001b 0 X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. Set the INT1SEL bit in the PMR register to 0 (P1_5, P1_7). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 69 of 453 0 1 0 Function Input port(1) Output port TRAIO input(1) INT1(2) 1 TRAIO input/INT1(1, 2) X TRAIO pulse output R8C/26 Group, R8C/27 Group 7. Programmable I/O Ports 3. Set the TOPCR bit in the TRAIOC register to 0 in modes except for pulse output mode. Table 7.23 Port P3_1/TRBO Register PD3 Timer RB Setting Bit PD3_1 - 0 Other than TRBO usage conditions Input port(1) 1 Other than TRBO usage conditions Output port X Refer to Table 7.24 TRBO Pin Setting Setting value Function TRBO output X: 0 or 1 NOTE: 1. Pulled up by setting the PU06 bit in the PUR0 register to 1. Table 7.24 TRBO Pin Setting Register PINSR2 TRBIOC Bit TRBOSEL TOCNT(1) TMOD1 TMOD0 0 0 0 1 Programmable waveform generation mode 0 0 1 0 Programmable one-shot generation mode 0 0 1 1 Programmable wait one-shot generation mode 1 0 1 Setting value 0 TRBMR Function P3_1 output port Other than above Other than TRBO usage conditions NOTE: 1. Set the TOCNT bit in the TRBIOC register to 0 in modes except for programmable waveform generation mode. Table 7.25 Port P3_3/INT3/SSI/TRCCLK Clock Synchronous Serial I/O with Chip Select (Refer to Table 16.4 Association between Communication Modes and I/O Pins.) TRCCR1 INTEN Register PD3 PMR Bit PD3_3 IICSEL SSI output control SSI input control 0 X 0 0 Other than 101b 0 Input port(1) 1 X 0 0 Other than 101b 0 Output port 0 X 0 0 Other than 101b 1 INT3 input(1) Setting value TCK2 TCK1 TCK0 Function(3) INT3EN 0 X 0 0 0 TRCCLK input(1) X 0 1 0 Other than 101b 0 SSI output(2) X 0 0 1 Other than 101b 0 SSI input(2) 1 0 1 X: 0 or 1 NOTES: 1. Pulled up by setting the PU06 bit in the PUR0 register to 1. 2. Set the SSISEL bit in the PMR register to 0 (P3_3). 3. When the SOOS bit is set to 1 (N-channel open drain output) and BIDE bit is set to 0 (standard mode) in the SSMR2 register, this pin is set to N-channel open drain output. Table 7.26 Port P3_4/SDA/SCS/(TRCIOC) Register PD3 PMR ICCR1 Bit PD3_4 IICSEL ICE 0 X 0 0 Other than TRCIOC usage conditions 1 0 0 0 Other than TRCIOC usage conditions 0 X 0 0 Other than TRCIOC usage conditions 1 0 0 0 Other than TRCIOC usage conditions 0 1 Setting value SSMR2 CSS1 Timer RC setting CSS0 - Function(2) Input port(1) Output port X X 0 0 0 Refer to Table 7.27 TRCIOC Pin Setting TRCIOC output 0 X 0 0 0 Refer to Table 7.27 TRCIOC Pin Setting TRCIOC input(1) X 0 X 1 0 Other than TRCIOC usage conditions SCS output X 0 X 1 1 Other than TRCIOC usage conditions SCS input(1) X 1 1 X X Other than TRCIOC usage conditions SDA input/output X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. N-channel open drain output by setting the CSOS bit in the SSMR2 register to 1 (N-channel open drain output). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 70 of 453 R8C/26 Group, R8C/27 Group Table 7.27 7. Programmable I/O Ports TRCIOC Pin Setting Register PINSR3 TRCOER Bit TRCIOCSEL EC PWM2 PWMC IOC2 IOC1 IOC0 1 0 1 1 X X X PWM mode waveform output 0 0 1 0 1 X Timer waveform output (output compare function) 1 X X Timer mode (input capture function) 1 0 1 Setting value 1 0 1 1 TRCMR TRCIOR1 1 0 1 0 Other than above Function Other than TRCIOC usage conditions X: 0 or 1 Table 7.28 Register Port P3_5/SCL/SSCK/(TRCIOD) PD3 Bit PMR ICCR1 Clock Synchronous Serial I/O with Chip Select (Refer to Table 16.4 Association between Communication Modes and I/O Pins.) Function(2) ICE SSCK output control SSCK input control - 0 X 0 0 Other than TRCIOD usage conditions 1 0 0 0 Other than TRCIOD usage conditions 0 X 0 0 Other than TRCIOD usage conditions 1 0 0 0 Other than TRCIOD usage conditions X X 0 0 0 Refer to Table 7.29 TRCIOD Pin Setting TRCIOD output 0 X 0 0 0 Refer to Table 7.29 TRCIOD Pin Setting TRCIOD input(1) X 0 X 1 0 Other than TRCIOD usage conditions SSCK output(2) X 0 X 0 1 Other than TRCIOD usage conditions SSCK input(1) X 1 1 X X Other than TRCIOD usage conditions SCL input/output PD3_5 IICSEL 0 1 Setting value Timer RC setting Input port(1) Output port X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. N-channel open drain output by setting the SCKOS bit in the SSMR2 register to 1 (N-channel open drain output). Table 7.29 TRCIOD Pin Setting Register PINSR3 TRCOER Bit TRCIODSEL EC PWM2 PWMD IOD2 IOD1 IOD0 1 0 1 1 X X X PWM mode waveform output 0 0 1 0 1 X Timer waveform output (output compare function) 1 X X Timer mode (input capture function) 1 Setting value 1 0 1 0 1 1 TRCMR TRCIOR1 1 0 1 0 Other than above X: 0 or 1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 71 of 453 Function Other than TRCIOD usage conditions R8C/26 Group, R8C/27 Group Table 7.30 7. Programmable I/O Ports Port P3_6/(TXD1)/(RXD1)/(INT1) Register PD3 PMR Bit PD3_6 TXD1EN SMD2 SMD1 SMD0 0 1 0 Setting value U1MR INTEN 0 X X X 0 X 0 0 0 0 0 X X X 0 X 0 0 0 0 0 X X X 1 X 0 0 0 1 0 0 1 0 1 0 0 0 1 0 1 0 X 1 0 0 Function INT1EN 1 1 0 0 X X X 0 Input port(1) Output port INT1 input(1, 2) TXD1 output(3, 4) RXD1 input(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. Set the INT1SEL bit in the PMR register to 1 (P3_6). 3. Set bits UART1SEL1 and UART1SEL0 in the PINSR1 register to 10b. 4. N-channel open drain output by setting the NCH bit in the U1C0 register to 1. Table 7.31 Port P3_7/TRAO/SSO/RXD1/(TXD1) Register PD3 PMR Bit PD3_7 IICSEL Setting value Clock Synchronous Serial I/O with Chip Select (Refer to Table 16.4 TRAMR Association between Communication Modes and I/O Pins.) SSO output control SSO input control TOENA UART1 setting Function(3) - 0 X 0 0 0 Other than TXD1, RXD1 Input port(1) usage conditions 1 X 0 0 0 Other than TXD1, RXD1 Output port usage conditions X X 0 0 X Refer to Table 7.32 Port P3_7 UART1 Setting Condition TXD1 output(4) 0 X 0 0 0 Refer to Table 7.32 Port P3_7 UART1 Setting Condition RXD1 input(1) X X 0 0 1 Other than TXD1, RXD1 TRAO output usage conditions X 0 1 0 X Other than TXD1, RXD1 SSO output(2) usage conditions X 0 0 1 X Other than TXD1, RXD1 SSO input(2) usage conditions X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. Set the SSISEL bit in the PMR register to 0 (P3_3). 3. N-channel open drain output by setting the SOOS bit in the SSMR2 register to 1 (N-channel open drain output). 4. N-channel open drain output by setting the NCH bit in the U1C0 register to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 72 of 453 R8C/26 Group, R8C/27 Group Table 7.32 Port P3_7 UART1 Setting Condition Register Bit 7. Programmable I/O Ports PINSR1 PMR 0 Setting value U1MR UART1SEL1 UART1SEL0 U1PINSEL TXD1SEL TXD1EN X X 1 0 1 1 0 1 X X X 0 SMD2 SMD1 SMD0 0 0 1 1 0 0 1 0 1 1 1 0 0 0 1 1 0 0 1 0 1 1 1 0 X X X Function TXD1 output RXD1 input Other than TXD1, RXD1 usage conditions Other than above X: 0 or 1 Table 7.33 Port P4_2/VREF Register ADCON1 Bit VCUT Setting value 0 Input port 1 Input port/VREF input Table 7.34 Function Port P4_5/INT0/(RXD1) Register PD4 INTEN Bit PD4_5 INT0EN 0 0 Other than 011b Input port(1) 1 0 Other than 011b Output port 0 1 Other than 011b INT0 input(1) 0 0 Setting value PINSR1 UART1SEL1 0 NOTE: 1. Pulled up by setting the PU11 bit in the PUR1 register to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 73 of 453 PMR UART1SEL0 1 Function U1PINSEL 1 RXD1(1) R8C/26 Group, R8C/27 Group Table 7.35 Port P4_6/XIN/XCIN Register Bit 7. Programmable I/O Ports CM0 CM1 CM01 CM04 CM05 CM13 CM12 CM11 X 0 1 0 X X 0 0 1 0 0 X 1 X 0 1 1 1 Setting value 0 1 1 0 1 X X 0 Circuit specifications Function Oscillation Feedback CM10 buffer resistor 0 OFF - Input port XIN clock oscillation (on-chip ON ON feedback resistor enabled) XIN clock oscillation (on-chip ON OFF feedback resistor disabled) OFF ON External clock input 0 XIN clock oscillation stop (on-chip OFF ON feedback resistor enabled) XIN clock oscillation stop (on-chip OFF OFF feedback resistor disabled) XIN clock oscillation stop (stop 1 OFF OFF mode) XCIN clock oscillation (on-chip ON ON feedback resistor enabled)(1) XCIN clock oscillation (on-chip ON OFF feedback resistor disabled)(1) 0 OFF ON External XCIN clock input(1) X 0 1 1 1 OFF ON OFF OFF OFF OFF XCIN clock oscillation stop (onchip feedback resistor enabled)(1) XCIN clock oscillation stop (onchip feedback resistor disabled)(1) XCIN clock oscillation stop (stop mode)(1) X: 0 or 1 NOTE: 1. For N, D version only. Table 7.36 Port P4_7/XOUT/XCOUT Register Bit CM0 CM1 CM01 CM04 CM05 CM13 CM12 CM11 X 0 1 0 X X 0 0 1 0 X 1 X 0 0 1 1 Setting value 1 Circuit specifications Function Oscillation Feedback CM10 buffer resistor 0 OFF - Input port XIN clock oscillation (on-chip ON ON feedback resistor enabled) XIN clock oscillation (on-chip ON OFF feedback resistor disabled) OFF ON External clock input 0 XIN clock oscillation stop (on-chip OFF ON feedback resistor enabled) XIN clock oscillation stop (on-chip OFF OFF feedback resistor disabled) 1 OFF OFF 0 ON ON 1 ON OFF OFF ON 0 OFF ON 1 OFF OFF OFF OFF 1 1 X X 0 X 0 0 1 1 XOUT pulled up(2) XCIN clock oscillation (on-chip feedback resistor enabled)(1, 2) XCIN clock oscillation (on-chip feedback resistor disabled)(1, 2) External XCIN clock input(2) XCIN clock oscillation stop (onchip feedback resistor enabled)(2) XCIN clock oscillation stop (onchip feedback resistor disabled)(2) XCOUT pulled up(2) X: 0 or 1 NOTES: 1. Since the XCIN-XCOUT oscillation buffer operates with internal step-down power, the XCOUT output level cannot be used as the CMOS level signal directly. 2. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 74 of 453 R8C/26 Group, R8C/27 Group Table 7.37 7. Programmable I/O Ports Port P5_3/TRCIOC Register PD5 Timer RC setting Bit PD5_3 - 0 Other than TRCIOC usage conditions Input port(1) Output port Setting value Function 1 Other than TRCIOC usage conditions X Refer to Table 7.38 TRCIOC Pin Setting TRCIOC output 0 Refer to Table 7.38 TRCIOC Pin Setting TRCIOC input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU12 bit in the PUR1 register to 1. Table 7.38 TRCIOC Pin Setting Register PINSR3 TRCOER Bit TRCIOCSEL EC PWM2 PWMC IOC2 IOC1 IOC0 0 0 1 1 X X X PWM mode waveform output 0 0 1 0 1 X Timer waveform output (output compare function) 1 X X Timer mode (input capture function) 0 0 Setting value TRCMR 0 0 0 0 1 TRCIOR1 1 0 1 0 Other than above Function Other than TRCIOC usage conditions X: 0 or 1 Table 7.39 Port P5_4/TRCIOD Register PD5 Timer RC setting Bit PD5_4 - 0 Other than TRCIOD usage conditions Input port(1) 1 Other than TRCIOD usage conditions Output port Setting value Function X Refer to Table 7.40 TRCIOD Pin Setting TRCIOD output 0 Refer to Table 7.40 TRCIOD Pin Setting TRCIOD input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU13 bit in the PUR1 register to 1. Table 7.40 TRCIOD Pin Setting Register PINSR3 TRCOER Bit TRCIODSEL ED PWM2 PWMD IOD2 IOD1 IOD0 0 0 1 1 X X X PWM mode waveform output 0 0 1 0 1 X Timer waveform output (output compare function) 1 X X Timer mode (input capture function) 0 Setting value 0 0 0 0 0 1 TRCMR TRCIOR1 1 0 1 0 Other than above X: 0 or 1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 75 of 453 Function Other than TRCIOD usage conditions R8C/26 Group, R8C/27 Group 7.5 7. Programmable I/O Ports Unassigned Pin Handling Table 7.41 lists the Unassigned Pin Handling. Table 7.41 Unassigned Pin Handling Pin Name Connection Ports P0, P1, P3_1, P3_3 to P3_7, * After setting to input mode, connect each pin to VSS via a resistor P4_3 to P4_5, P5_3, P5_4 (pull-down) or connect each pin to VCC via a resistor (pull-up).(2) * After setting to output mode, leave these pins open.(1, 2) Ports P4_6, P4_7 Connect to VCC via a pull-up resistor(2) Port P4_2, VREF Connect to VCC Connect to VCC via a pull-up resistor(2) RESET (3) NOTES: 1. If these ports are set to output mode and left open, they remain in input mode until they are switched to output mode by a program. The voltage level of these pins may be undefined and the power current may increase while the ports remain in input mode. The content of the direction registers may change due to noise or program runaway caused by noise. In order to enhance program reliability, the program should periodically repeat the setting of the direction registers. 2. Connect these unassigned pins to the MCU using the shortest wire length (2 cm or less) possible. 3. When the power-on reset function is in use. MCU Port P0, P1, (Input mode ) : P3_1, P3_3 to P3_7, : P4_3 to P4_5, P5_3, P5_4 (Input mode) (Output mode) Port P4_6, P4_7 RESET(1) Port P4_2/VREF NOTE: 1. When the power-on reset function is in use. Figure 7.14 Unassigned Pin Handling Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 76 of 453 : : Open R8C/26 Group, R8C/27 Group 8. 8. Processor Mode Processor Mode 8.1 Processor Modes Single-chip mode can be selected as the processor mode. Table 8.1 lists Features of Processor Mode. Figure 8.1 shows the PM0 Register and Figure 8.2 shows the PM1 Register. Table 8.1 Features of Processor Mode Processor Mode Single-chip mode Accessible Areas Pins Assignable as I/O Port Pins SFR, internal RAM, internal ROM All pins are I/O ports or peripheral function I/O pins Processor Mode Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address PM0 0004h Bit Symbol Bit Name -- Reserved bits (b2-b0) PM03 -- (b7-b4) Softw are reset bit After Reset 00h Function Set to 0. RW RW The MCU is reset w hen this bit is set to 1. When read, the content is 0. Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW -- NOTE: 1. Set the PRC1 bit in the PRCR register to 1 (w rite enable) before rew riting the PM0 register. Figure 8.1 PM0 Register Processor Mode Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address PM1 0005h Bit Symbol Bit Name -- Reserved bits (b1-b0) PM12 -- (b6-b3) -- (b7) WDT interrupt/reset sw itch bit After Reset 00h Function Set to 0. 0 : Watchdog timer interrupt 1 : Watchdog timer reset(2) Nothing is assigned. If necessary, set to 0. When read, the content is 0. Reserved bit Set to 0. NOTES: 1. Set the PRC1 bit in the PRCR register to 1 (w rite enable) before rew riting the PM1 register. 2. The PM12 bit is set to 1 by a program (It remains unchanged even if 0 is w ritten to it). When the CSPRO bit in the CSPR register is set to 1 (count source protect mode enabled), the PM12 bit is automatically set to 1. Figure 8.2 PM1 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 77 of 453 RW RW RW -- RW R8C/26 Group, R8C/27 Group 9. 9. Bus Bus The bus cycles differ when accessing ROM/RAM, and when accessing SFR. Table 9.1 lists Bus Cycles by Access Space of the R8C/26 Group and Table 9.2 lists Bus Cycles by Access Space of the R8C/27 Group. ROM/RAM and SFR are connected to the CPU by an 8-bit bus. When accessing in word (16-bit) units, these areas are accessed twice in 8-bit units. Table 9.3 lists Access Units and Bus Operations. Table 9.1 Bus Cycles by Access Space of the R8C/26 Group Access Area SFR ROM/RAM Table 9.2 Bus Cycle 2 cycles of CPU clock 1 cycle of CPU clock Bus Cycles by Access Space of the R8C/27 Group Access Area SFR/Data flash Program ROM/RAM Table 9.3 Bus Cycle 2 cycles of CPU clock 1 cycle of CPU clock Access Units and Bus Operations SFR, data flash Area Even address Byte access CPU clock CPU clock Even Address Data Odd address Byte access CPU clock Odd Data Even Data Even+1 Data CPU clock Data Data Odd Data Data CPU clock Data Address Data Address CPU clock Address Even CPU clock Data Odd address Word access Address Data Address Even address Word access ROM (program ROM), RAM Address Data Even Data Even+1 Data CPU clock Odd Odd+1 Data Data Address Data Odd+1 Odd Data Data However, only following SFRs are connected with the 16-bit bus: Timer RC: registers TRC, TRCGRA, TRCGRB, TRCGRC, and TRCGRD Therefore, when accessing in word (16-bit) unit, 16-bit data is accessed at a time. The bus operation is the same as "Area: SFR, data flash, even address byte access" in Table 9.3 Access Units and Bus Operations, and 16-bit data is accessed at a time. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 78 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit 10. Clock Generation Circuit The clock generation circuit has: * XIN clock oscillation circuit * XCIN clock oscillation circuit (For N, D version only) * Low-speed on-chip oscillator * High-speed on-chip oscillator However, use one of the XIN clock oscillation circuit or the XCIN clock oscillation circuit because they share the XIN/XCIN pin and the XOUT/XCOUT pin. (For J, K version, the XCIN clock oscillation circuit cannot be used.) Table 10.1 lists the Specifications of Clock Generation Circuit. Figure 10.1 shows a Clock Generation Circuit. Figures 10.2 to 10.9 show clock associated registers. Figure 10.10 shows a Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit. Table 10.1 Specifications of Clock Generation Circuit Clock frequency 0 to 20 MHz 32.768 kHz On-Chip Oscillator High-Speed On-Chip Low-Speed On-Chip Oscillator Oscillator * CPU clock source * CPU clock source * Peripheral function * Peripheral function clock source clock source * CPU and peripheral * CPU and peripheral function clock function clock sources when XIN sources when XIN clock stops oscillating clock stops oscillating Approx. 125 kHz Approx. 40 MHz(5) Connectable oscillator Oscillator connect pins Oscillation stop, restart function Oscillator status after reset Others * Ceramic resonator * Crystal oscillator * Crystal oscillator - - XIN, XOUT(1) XCIN, XCOUT(1) -(1) -(1) Usable Usable Usable Usable Stop Stop Stop Oscillate Item Applications XIN Clock Oscillation Circuit XCIN Clock Oscillation Circuit (For N, D Version Only) * CPU clock source * Peripheral function clock source * CPU clock source * Peripheral function clock source - * Externally generated * Externally generated clock can clock can be input(4) * On-chip feedback be input(2, 3) * On-chip feedback resistor RfXCIN resistor RfXIN (connected/ not (connected/ not connected, selectable) connected, selectable) - NOTES: 1. These pins can be used as P4_6 or P4_7 when using the on-chip oscillator clock as the CPU clock while the XIN clock oscillation circuit and XCIN clock oscillation circuit is not used. 2. Set the CM01 bit in the CM0 register to 0 (XIN clock), the CM05 bit in the CM0 register to 1 (XIN clock stopped), and the CM13 bit in the CM1 register to 1 (XIN-XOUT pin) when an external clock is input. 3. When 32.768 kHz is used as an external clock, set the CM01 bit in the CM0 register to 1 (XCIN clock). In other cases, set the CM01 bit in the CM0 register to 0 (XIN clock). 4. Set the CM01 bit in the CM0 register to 1 (XCIN clock) and the CM04 bit in the CM0 register to 1 (XCIN clock oscillator) when an external clock is input. 5. The clock frequency is automatically set to up to 20 MHz by a divider when using the high-speed on-chip oscillator as the CPU clock source. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 79 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Clock prescaler fC4 fC 1/4 fC32 1/8 FRA1 register Frequency adjustable High-speed on-chip oscillator FRA00 fOCO40M FRA2 register Divider fOCO-F On-chip oscillator clock FRA01 = 1 FRA01 = 0 Stop signal Low-speed on-chip oscillator CM14 SSU / I2C bus INT0 Timer RA A/D Timer RB Timer RC Timer RE converter UART0 fOCO Power-on reset circuit fOCO-S Voltage detection circuit XOUT/XCOUT(1) XIN/XCIN(1) fOCO128 Watchdog timer Divider CM01 = 0 f1 b CM13 f2 c CM05 Oscillation stop detection f4 d f8 e g OCD2 = 1 f32 CM01 = 0 a CM04 CM01 XIN clock CPU clock Divider OCD2 = 0 CM01 = 1 XCIN clock System clock CM02 CM10 = 1 (stop mode) S Q R RESET Power-on reset Software reset Interrupt request WAIT instruction 1/2 a g e d c b S Q 1/2 1/2 1/2 1/2 R CM06 = 0 CM17 to CM16 = 11b CM06 = 1 CM06 = 0 CM17 to CM16 = 10b CM01, CM02, CM04, CM05, CM06: Bits in CM0 register CM10, CM13, CM14, CM16, CM17: Bits in CM1 register OCD0, OCD1, OCD2: Bits in OCD register FRA00, FRA01: Bits in FRA0 register h CM06 = 0 CM17 to CM16 = 01b CM06 = 0 CM17 to CM16 = 00b Detail of divider Oscillation Stop Detection Circuit Forcible discharge when OCD0 = 0 XIN clock Pulse generation circuit for clock edge detection and charge, discharge control circuit Charge, discharge circuit Oscillation stop detection interrupt generation circuit detection OCD1 Watchdog timer interrupt Voltage monitor 1 interrupt Voltage monitor 2 interrupt OCD2 bit switch signal CM14 bit switch signal NOTE: 1. For J, K version, the XCIN clock oscillation circuit cannot be used. Figure 10.1 Clock Generation Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 80 of 453 Oscillation stop detection, Watchdog timer, Voltage monitor 1 interrupt, Voltage monitor 2 interrupt UART1 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit System Clock Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol Address 0006h CM0 Bit Symbol Bit Name -- Reserved bit (b0) (12) After Reset 01101000b Function Set to 0. RW RW XIN-XCIN sw itch bit 0 : XIN clock 1 : XCIN clock RW WAIT peripheral function clock stop bit 0 : Peripheral function clock does not stop in w ait mode 1 : Peripheral function clock stops in w ait mode RW CM03 XCIN-XCOUT drive capacity select bit(2) 0 : Low 1 : High RW CM04 XCIN clock (XCIN-XCOUT) oscillate bit(3, 4, 5, 12) 0 : XCIN clock stops 1 : XCIN clock oscillates (6, 7) CM01 CM02 CM05 XIN clock (XIN-XOUT) stop bit(3, 8) 0 : XIN clock oscillates 1 : XIN clock stops (10) CM06 System clock division select bit 0(11) 0 : CM16, CM17 enabled 1 : Divide-by-8 mode Reserved bit Set to 0. -- (b7) RW (9) RW RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the CM0 register. 2. The MCU enters stop mode, the CM03 bit is set to 1 (high). Rew rite the CM03 bit w hile the XCIN clock oscillation stabilizes. 3. P4_6 and P4_7 can be used as input ports w hen the CM04 bit is set to 0 (XCIN clock stops), the CM05 bit is set to 1 (XIN clock stops) and the CM13 bit in the CM1 register is set to 0 (P4_6, P4_7). 4. The CM04 bit can be set to 1 by a program but cannot be set to 0. 5. When the CM10 bit is set to 1 (stop mode) and the CM04 bit is set to 1 (XCIN clock oscillates), the XCOUT (P4_7) pin goes "H". When the CM04 bit is set to 0 (XCIN clock stops), P4_7 (XCOUT) enters input mode. 6. To use the XCIN clock, set the CM04 bit to 1. Also, set ports P4_6 and P4_7 as input ports w ithout pull-up. 7. Set the CM01 bit to 1 (XCIN clock). 8. The CM05 bit stops the XIN clock w hen the high-speed on-chip oscillator mode, low -speed on-chip oscillator mode is selected. Do not use this bit to detect w hether the XIN clock is stopped. To stop the XIN clock, set the bits in the follow ing order: (a) Set bits OCD1 to OCD0 in the OCD register to 00b. (b) Set the OCD2 bit to 1 (selects on-chip oscillator clock). 9. Set the CM01 bit to 0 (XIN clock). 10. During external clock input, only the clock oscillation buffer is turned off and clock input is acknow ledged. 11. When entering stop mode, the CM06 bit is set to 1 (divide-by-8 mode). 12. For J, K version, the XCIN clock oscillation circuit cannot be used. Do not set to 1. Figure 10.2 CM0 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 81 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit System Clock Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol CM1 Bit Symbol CM10 Address 0007h Bit Name All clock stop control bit(4, 7, 8) After Reset 00100000b Function 0 : Clock operates 1 : Stops all clocks (stop mode) RW RW CM11 XIN-XOUT on-chip feedback resistor 0 : On-chip feedback resistor enabled select bit 1 : On-chip feedback resistor disabled RW CM12 XCIN-XCOUT on-chip feedback resistor select bit(10) 0 : On-chip feedback resistor enabled 1 : On-chip feedback resistor disabled RW Port XIN-XOUT sw itch bit 0 : Input ports P4_6, P4_7 1 : XIN-XOUT pin RW Low -speed on-chip oscillation stop bit(5, 6, 8) 0 : Low -speed on-chip oscillator on 1 : Low -speed on-chip oscillator off RW 0 : Low 1 : High RW (7, 9) CM13 CM14 (2) CM15 XIN-XOUT drive capacity select bit (3) System clock division select bits 1 CM16 CM17 b7 b6 0 0 : No division mode 0 1 : Divide-by-2 mode 1 0 : Divide-by-4 mode 1 1 : Divide-by-16 mode RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the CM1 register. 2. When entering stop mode, the CM15 bit is set to 1 (drive capacity high). 3. When the CM06 bit is set to 0 (bits CM16, CM17 enabled), bits CM16 to CM17 are enabled. 4. If the CM10 bit is set to 1 (stop mode), the on-chip feedback resistor is disabled. 5. When the OCD2 bit is set to 0 (XIN clock selected), the CM14 bit is set to 1 (low -speed on-chip oscillator stopped). When the OCD2 bit is set to 1 (on-chip oscillator clock selected), the CM14 bit is set to 0 (low -speed on-chip oscillator on). It remains unchanged even if 1 is w ritten to it. 6. When using the voltage monitor 1 interrupt or voltage monitor 2 interrupt (w hen using the digital filter), set the CM14 bit to 0 (low -speed on-chip oscillator on). 7. When the CM10 bit is set to 1 (stop mode) and the CM13 bit is set to 1 (XIN-XOUT pin), the XOUT (P4_7) pin goes "H". When the CM13 bit is set to 0 (input ports, P4_6, P4_7), P4_7 (XOUT) enters input mode. 8. In count source protect mode (refer to 13.2 Count Source Protection Mode Enabled), the value remains unchanged even if bits CM10 and CM14 are set. 9. Once the CM13 bit is set to 1 by a program, it cannot be set to 0. 10. For J, K version, the XCIN clock oscillation circuit cannot be used. Set to 0. Figure 10.3 CM1 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 82 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Oscillation Stop Detection Register(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol OCD Bit Symbol OCD0 OCD1 Address After Reset 000Ch 00000100b Bit Name Function Oscillation stop detection enable 0 : Oscillation stop detection function disabled(2) bit(7) 1 : Oscillation stop detection function enabled Oscillation stop detection interrupt enable bit (4) OCD2 OCD3 -- (b7-b4) 0 : Disabled(2) 1 : Enabled RW RW RW (7) System clock select bit 0 : Selects XIN clock 1 : Selects on-chip oscillator clock(3) RW Clock monitor bit(5, 6) 0 : XIN clock oscillates 1 : XIN clock stops RO Reserved bits Set to 0. RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting to the OCD register. 2. Set bits OCD1 to OCD0 to 00b before entering stop mode, high-speed on-chip oscillator mode, or low -speed on-chip oscillator mode (XIN clock stops). 3. The CM14 bit is set to 0 (low -speed on-chip oscillator on) if the OCD2 bit is set to 1 (on-chip oscillator clock selected). 4. The OCD2 bit is automatically set to 1 (on-chip oscillator clock selected) if a XIN clock oscillation stop is detected w hile bits OCD1 to OCD0 are set to 11b. If the OCD3 bit is set to 1 (XIN clock stopped), the OCD2 bit remains unchanged even w hen set to 0 (XIN clock selected). 5. The OCD3 bit is enabled w hen the OCD0 bit is set to 1 (oscillation stop detection function enabled). 6. The OCD3 bit remains 0 (XIN clock oscillates) if bits OCD1 to OCD0 are set to 00b. 7. Refer to Figure 10.18 Procedure for Sw itching Clock Source from Low -Speed On-Chip Oscillator to XIN Clock for the sw itching procedure w hen the XIN clock re-oscillates after detecting an oscillation stop. Figure 10.4 OCD Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 83 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit High-Speed On-Chip Oscillator Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 Symbol FRA0 Bit Symbol FRA00 FRA01 -- (b7-b2) Address 0023h Bit Name High-speed on-chip oscillator enable bit After Reset 00h Function 0 : High-speed on-chip oscillator off 1 : High-speed on-chip oscillator on RW RW (3) High-speed on-chip oscillator select bit(2) 0 : Selects low -speed on-chip oscillator 1 : Selects high-speed on-chip oscillator Reserved bits Set to 0. RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA0 register. 2. Change the FRA01 bit under the follow ing conditions. * FRA00 = 1 (high-speed on-chip oscillation) * The CM14 bit in the CM1 register = 0 (low -speed on-chip oscillator on) * Bits FRA22 to FRA20 in the FRA2 register: All divide ratio mode settings are supported w hen VCC = 3.0 to 5.5 V 000b to 111b (other than K version) Divide ratio of 4 or more w hen VCC = 2.7 to 5.5 V or K version 010b to 111b Divide ratio of 8 or more w hen VCC = 2.2 to 5.5 V (for N, D version only) 110b to 111b 3. When setting the FRA01 bit to 0 (low -speed on-chip oscillator selected), do not set the FRA00 bit to 0 (high-speed on-chip oscillator off) at the same time. Set the FRA00 bit to 0 after setting the FRA01 bit to 0. High-Speed On-Chip Oscillator Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA1 Address 0024h After Reset When Shipping Function The frequency of the high-speed on-chip oscillator is adjusted w ith bits 0 to 7. High-speed on-chip oscillator frequency = 40 MHz (FRA1 register = value w hen shipping) Setting the FRA1 register to a low er value results in a higher frequency. Setting the FRA1 register to a higher value results in a low er frequency.(2) RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA1 register. 2. When changing the values of the FRA1 register, adjust the FRA1 register so that the frequency of the high-speed on-chip oscillator clock w ill be 40 MHz or less. Figure 10.5 Registers FRA0 and FRA1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 84 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit High-Speed On-Chip Oscillator Control Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol FRA2 Bit Symbol FRA20 Address 0025h Bit Name High-speed on-chip oscillator frequency sw itching bits After Reset 00h Function Selects the dividing ratio for the highspeed on-chip oscillator clock. b2 b1 b0 RW RW (2) 0 0 0: Divide-by-2 mode 0 0 1: Divide-by-3 mode(2) 0 1 0: Divide-by-4 mode 0 1 1: Divide-by-5 mode 1 0 0: Divide-by-6 mode 1 0 1: Divide-by-7 mode 1 1 0: Divide-by-8 mode 1 1 1: Divide-by-9 mode FRA21 FRA22 -- (b7-b3) Reserved bits Set to 0. RW RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA2 register. 2. Do not set in K version. High-Speed On-Chip Oscillator Control Register 4 (For N, D Version Only) b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA4 Address 0029h After Reset When Shipping Function Stores data for frequency correction w hen VCC = 2.7 to 5.5 V. (The value is the same as that of the FRA1 register after a reset.) Optimal frequency correction to match the voltage conditions can be achieved by transferring this value to the FRA1 register. RW RO High-Speed On-Chip Oscillator Control Register 6 (For N, D Version Only) b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA6 Address 002Bh After Reset When Shipping Function Stores data for frequency correction w hen VCC = 2.2 to 5.5 V. Optimal frequency correction to match the voltage conditions can be achieved by transferring this value to the FRA1 register. RW RO High-Speed On-Chip Oscillator Control Register 7 (For N, D Version Only) b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA7 Address 002Ch After Reset When Shipping Function 36.864 MHz frequency correction data is stored. The oscillation frequency of the high-speed on-chip oscillator can be adjusted to 36.864 MHz by transferring this value to the FRA1 register. Figure 10.6 Registers FRA2, FRA4, FRA6, and FRA7 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 85 of 453 RW RO R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Clock Prescaler Reset Flag (For N, D Version Only) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 Symbol Address 0028h CPSRF Bit Symbol Bit Name -- Reserved bits (b6-b0) After Reset 00h Function Set to 0. (1) CPSR Clock prescaler reset flag Setting this bit to 1 initializes the clock prescaler. (When read, the content is 0) RW RW RW NOTE: 1. Only w rite 1 to this bit w hen selecting the XCIN clock as the CPU clock, . Figure 10.7 CPSRF Register Voltage Detection Register 2(1) (N, D Version) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol VCA2 Bit Symbol VCA20 -- (b4-b1) Address 0032h Bit Name Internal pow er low consumption enable bit(6) After Reset(5) The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 00100000b Function 0 : Disables low consumption 1 : Enables low consumption RW RW Reserved bits Set to 0. VCA25 Voltage detection 0 enable bit(2) 0 : Voltage detection 0 circuit disabled 1 : Voltage detection 0 circuit enabled RW VCA26 Voltage detection 1 enable bit(3) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(4) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 0 reset, set the VCA25 bit to 1. After the VCA25 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 1 interrupt/reset or the VW1C3 bit in the VW1C register, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 5. Softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. 6. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.10 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 10.8 VCA2 Register (N, D Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 86 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Voltage Detection Register 2(1) (J, K Version) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol VCA2 Bit Symbol Address After Reset(4) The LVD1ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 1 reset or LVD1ON bit in the OFS register is set to 0, and hardw are reset : 0100000b 0032h Bit Name Internal pow er low consumption enable bit(5) Function 0 : Disables low consumption 1 : Enables low consumption Reserved bits Set to 0. VCA26 Voltage detection 1 enable bit(2) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(3) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW VCA20 -- (b5-b1) RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 1 reset, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. Softw are reset, w atchdog timer reset, or voltage monitor 2 reset do not affect this register. 5. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.10 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 10.9 VCA2 Register (J, K Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 87 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Exit wait mode by interrupt Handling procedure of internal power low consumption enabled by VCA20 bit (Note 1) In interrupt routine Step (1) Enter low-speed clock mode or low-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) Step (7) (Wait until XIN clock oscillation stabilizes) Step (4) Enter wait mode(4) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (7) (Wait until XIN clock oscillation stabilizes) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode If it is necessary to start the high-speed clock or the high-speed on-chip oscillator in the interrupt routine, execute steps (5) to (7) in the interrupt routine. Interrupt handling Step (1) Enter low-speed clock mode or low-speed on-chip oscillator mode Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) If the high-speed clock or high-speed on-chip oscillator is started in the interrupt routine, execute steps (1) to (3) at the last of the interrupt routine. Interrupt handling completed NOTES: 1. Execute this routine to handle all interrupts generated in wait mode. However, this does not apply if it is not necessary to start the high-speed clock or high-speed on-chip oscillator during the interrupt routine. 2. Do not set the VCA20 bit to 0 with the instruction immediately after setting the VCA20 bit to 1. Also, do not do the opposite. 3. When the VCA20 bit is set to 1, do not set the CM10 bit to 1 (stop mode). 4. When entering wait mode, follow 10.7.2 Wait Mode. VCA20: Bit in VCA2 register Figure 10.10 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 88 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit The clocks generated by the clock generation circuits are described below. 10.1 XIN Clock This clock is supplied by the XIN clock oscillation circuit. This clock is used as the clock source for the CPU and peripheral function clocks. The XIN clock oscillation circuit is configured by connecting a resonator between the XIN and XOUT pins. The XIN clock oscillation circuit includes an on-chip feedback resistor, which is disconnected from the oscillation circuit in stop mode in order to reduce the amount of power consumed by the chip. The XIN clock oscillation circuit may also be configured by feeding an externally generated clock to the XIN pin. Figure 10.11 shows Examples of XIN Clock Connection Circuit. In reset and after reset, the XIN clock stops. The XIN clock starts oscillating when the CM05 bit in the CM0 register is set to 0 (XIN clock oscillates) after setting the CM01 bit in the CM0 register to 1 (XIN clock) and the CM13 bit in the CM1 register to 1 (XIN- XOUT pin). To use the XIN clock for the CPU clock source, set the OCD2 bit in the OCD register to 0 (select XIN clock) after the XIN clock is oscillating stably. The power consumption can be reduced by setting the CM05 bit in the CM0 register to 1 (XIN clock stops) if the OCD2 bit is set to 1 (select on-chip oscillator clock). When an external clock is input to the XIN pin are input, the XIN clock does not stop if the CM05 bit is set to 1. If necessary, use an external circuit to stop the clock. This MCU has an on-chip feedback resistor and on-chip resistor disable/enable switching is possible by the CM11 bit in the CM1 register. In stop mode, all clocks including the XIN clock stop. Refer to 10.5 Power Control for details. MCU (on-chip feedback resistor) MCU (on-chip feedback resistor) XIN XIN XOUT XOUT Open Rf(1) Rd(1) Externally derived clock CIN COUT VCC VSS Ceramic resonator external circuit External clock input circuit NOTE: 1. Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the manufacturer of the oscillator. Use high drive when oscillation starts and, if it is necessary to switch the oscillation drive capacity, do so after oscillation stabilizes. When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added to the chip externally, insert a feedback resistor between XIN and XOUT following the instructions. To use this MCU of N, D version with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Figure 10.11 Examples of XIN Clock Connection Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 89 of 453 R8C/26 Group, R8C/27 Group 10.2 10. Clock Generation Circuit On-Chip Oscillator Clocks These clocks are supplied by the on-chip oscillators (high-speed on-chip oscillator and a low-speed on-chip oscillator). The on-chip oscillator clock is selected by the FRA01 bit in the FRA0 register. 10.2.1 Low-Speed On-Chip Oscillator Clock The clock generated by the low-speed on-chip oscillator is used as the clock source for the CPU clock, peripheral function clock, fOCO, and fOCO-S. After reset, the on-chip oscillator clock generated by the low-speed on-chip oscillator divided by 8 is selected as the CPU clock. If the XIN clock stops oscillating when bits OCD1 to OCD0 in the OCD register are set to 11b, the low-speed on-chip oscillator automatically starts operating, supplying the necessary clock for the MCU. The frequency of the low-speed on-chip oscillator varies depending on the supply voltage and the operating ambient temperature. Application products must be designed with sufficient margin to allow for frequency changes. 10.2.2 High-Speed On-Chip Oscillator Clock The clock generated by the high-speed on-chip oscillator is used as the clock source for the CPU clock, peripheral function clock, fOCO, fOCO-F, and fOCO40M. To use the high-speed on-chip oscillator clock as the clock source for the CPU clock, peripheral clock, fOCO, and fOCO-F, set bits FRA20 to FRA22 in the FRA2 register as follows: * All divide ratio mode settings are supported when VCC = 3.0 to 5.5 V 000b to 111b (other than K version) * Divide ratio of 4 or more when VCC = 2.7 to 5.5 V or K version 010b to 111b * Divide ratio of 8 or more when VCC = 2.2 to 5.5 V (for N, D version only) 110b to 111b After reset, the on-chip oscillator clock generated by the high-speed on-chip oscillator stops. Oscillation is started by setting the FRA00 bit in the FRA0 register to 1 (high-speed on-chip oscillator on). The frequency can be adjusted by registers FRA1 and FRA2. The frequency correction data (the value is the same as that of the FRA1 register after a reset) corresponding to the supply voltage ranges VCC = 2.7 to 5.5 V is stored in FRA4 register. Furthermore, the frequency correction data corresponding to the supply voltage ranges VCC = 2.2 to 5.5 V is stored in FRA6 register (for N, D version only). To use separate correction values to match these voltage ranges, transfer them from FRA4 or FRA6 register to the FRA1 register. The frequency correction data of 36.864 MHz is stored in the FRA7 register (for N, D version only). To set the frequency of the high-speed on-chip oscillator to 36.864 MHz, transfer the correction value in the FRA7 register to the FRA1 register before use. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in UART mode (refer to Table 15.7 Bit Rate Setting Example in UART Mode (Internal Clock Selected)). Since there are differences in the amount of frequency adjustment among the bits in the FRA1 register, make adjustments by changing the settings of individual bits. Adjust the FRA1 register so that the frequency of the high-speed on-chip oscillator clock will be 40 MHz or less. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 90 of 453 R8C/26 Group, R8C/27 Group 10.3 10. Clock Generation Circuit XCIN Clock (For N, D Version Only) This clock is supplied by the XCIN clock oscillation circuit. This clock is used as the clock source for the CPU clock, peripheral function clock. The XCIN clock oscillation circuit is configured by connecting a resonator between the XCIN and XCOUT pins. The XCIN clock oscillation circuit includes an on-chip a feedback resistor, which is disconnected from the oscillation circuit in stop mode in order to reduce the amount of power consumed in the chip. The XCIN clock oscillation circuit may also be configured by feeding an externally generated clock to the XCIN pin. Figure 10.12 shows Examples of XCIN Clock Connection Circuits. During and after reset, the XCIN clock stops. The XCIN clock starts oscillating when the CM01 bit in the CM0 register is set to 1 (XCIN clock) and the CM04 bit in the CM0 register is set to 1 (XCIN-XCOUT pin). To use the XCIN clock for the CPU clock source, set the OCD2 bit in the OCD register to 0 (selects XIN clock) after the XCIN clock is oscillating stably. This MCU has an on-chip feedback resistor and on-chip resistor disable/enable switching is possible by the CM12 bit in the CM1 register. In stop mode, all clocks including the XCIN clock stop. Refer to 10.5 Power Control for details. MCU (on-chip feedback resistor) MCU (on-chip feedback resistor) XCIN XCIN XCOUT XCOUT Open Rf(1) Rd(1) CIN COUT Externally derived clock VCC VSS External crystal oscillator circuit External clock input circuit NOTE: 1. Insert a damping resistor and feedback resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the manufacturer of the oscillator. When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added to the chip externally, insert a feedback resistor between XCIN and XCOUT following the instructions. Figure 10.12 Examples of XCIN Clock Connection Circuits Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 91 of 453 R8C/26 Group, R8C/27 Group 10.4 10. Clock Generation Circuit CPU Clock and Peripheral Function Clock There are a CPU clock to operate the CPU and a peripheral function clock to operate the peripheral functions. Refer to Figure 10.1 Clock Generation Circuit. 10.4.1 System Clock The system clock is the clock source for the CPU and peripheral function clocks. Either the XIN clock and XCIN clock or the on-chip oscillator clock can be selected. (For J, K version, the XCIN clock cannot be selected.) 10.4.2 CPU Clock The CPU clock is an operating clock for the CPU and watchdog timer. The system clock can be divided by 1 (no division), 2, 4, 8, or 16 to produce the CPU clock. Use the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register to select the value of the division. Use the XCIN clock while the XCIN clock oscillation stabilizes. After reset, the low-speed on-chip oscillator clock divided by 8 provides the CPU clock. When entering stop mode from high-speed clock mode, the CM06 bit is set to 1 (divide-by-8 mode). (For J, K version, the XCIN clock cannot be selected.) 10.4.3 Peripheral Function Clock (f1, f2, f4, f8, and f32) The peripheral function clock is the operating clock for the peripheral functions. The clock fi (i = 1, 2, 4, 8, and 32) is generated by the system clock divided by i. The clock fi is used for timers RA, RB, RC, and RE, the serial interface and the A/D converter. When the WAIT instruction is executed after setting the CM02 bit in the CM0 register to 1 (peripheral function clock stops in wait mode), the clock fi stop. 10.4.4 fOCO fOCO is an operating clock for the peripheral functions. fOCO runs at the same frequency as the on-chip oscillator clock and can be used as the source for timer RA. When the WAIT instruction is executed, the clocks fOCO does not stop. 10.4.5 fOCO40M fOCO40M is used as the count source for timer RC. fOCO40M is generated by the high-speed on-chip oscillator and supplied by setting the FRA00 bit to 1. When the WAIT instruction is executed, the clock fOCO40M does not stop. fOCO40M can be used with supply voltage VCC = 3.0 to 5.5 V. 10.4.6 fOCO-F fOCO-F is used as the count source for the A/D converter. fOCO-F is generated by the high-speed on-chip oscillator and supplied by setting the FRA00 bit to 1. When the WAIT instruction is executed, the clock fOCO-F does not stop. 10.4.7 fOCO-S fOCO-S is an operating clock for the watchdog timer and voltage detection circuit. fOCO-S is supplied by setting the CM14 bit to 0 (low-speed on-chip oscillator on) and uses the clock generated by the low-speed onchip oscillator. When the WAIT instruction is executed or in count source protect mode of the watchdog timer, fOCO-S does not stop. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 92 of 453 R8C/26 Group, R8C/27 Group 10.4.8 fC4 and fC32 The clock fC4 is used for timer RE and the clock fC32 is used for timer RA. Use fC4 and fC32 while the XCIN clock oscillation stabilizes. (For J, K version, fC4 and fC32 cannot be used.) 10.4.9 fOCO128 fOCO128 is generated by fOCO divided by 128. The clock fOCO128 is used for capture signal of timer RC's TRCGRA register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 93 of 453 10. Clock Generation Circuit R8C/26 Group, R8C/27 Group 10.5 10. Clock Generation Circuit Power Control There are three power control modes. All modes other than wait mode and stop mode are referred to as standard operating mode. 10.5.1 Standard Operating Mode Standard operating mode is further separated into four modes. In standard operating mode, the CPU clock and the peripheral function clock are supplied to operate the CPU and the peripheral function clocks. Power consumption control is enabled by controlling the CPU clock frequency. The higher the CPU clock frequency, the more processing power increases. The lower the CPU clock frequency, the more power consumption decreases. When unnecessary oscillator circuits stop, power consumption is further reduced. Before the clock sources for the CPU clock can be switched over, the new clock source needs to be oscillating and stable. If the new clock source is the XIN clock or XCIN clock, allow sufficient wait time in a program until oscillation is stabilized before exiting. Table 10.2 Settings and Modes of Clock Associated Bits OCD Register Modes OCD2 High-speed clock mode Low-speed clock mode(1) High-speed on-chip oscillator mode Low-speed on-chip oscillator mode No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 CM1 Register CM17, CM16 00b 01b 10b - 11b 00b 01b 10b - 11b 00b 01b 10b - 11b 00b 01b 10b - 11b -: Can be 0 or 1, no change in outcome NOTE: 1. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 94 of 453 CM0 Register CM14 CM13 CM06 CM05 CM04 - - - - - - - - - - - - - - - 0 0 0 0 0 1 1 1 1 1 - - - - - - - - - - - - - - - 0 0 0 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 - - - - - - - - - - - - - - - - - - - - 1 1 1 1 1 - - - - - - - - - - FRA0 Register CM01 FRA01 FRA00 0 0 0 0 0 1 1 1 1 1 - - - - - - - - - - - - - - - - - - - - 1 1 1 1 1 0 0 0 0 0 - - - - - - - - - - 1 1 1 1 1 - - - - - R8C/26 Group, R8C/27 Group 10.5.1.1 10. Clock Generation Circuit High-Speed Clock Mode The XIN clock divided by 1 (no division), 2, 4, 8, or 16 provides the CPU clock. Set the CM06 bit to 1 (divideby-8 mode) when transiting to high-speed on-chip oscillator mode, low-speed on-chip oscillator mode. If the CM14 bit is set to 0 (low-speed on-chip oscillator on) or the FRA00 bit in the FRA0 register is set to 1 (highspeed on-chip oscillator on), fOCO can be used as timer RA. When the FRA00 bit is set to 1, fOCO40M can be used as timer RC. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. 10.5.1.2 Low-Speed Clock Mode (For N, D Version Only) The XCIN clock divided by 1 (no division), 2, 4, 8, or 16 provides the CPU clock. Set the CM06 bit to 1 (divide by-8 mode) when transiting to high-speed on-chip oscillator mode, low-speed on-chip oscillator mode. If the CM14 bit is set to 0 (low-speed on-chip oscillator on) or the FRA00 bit in the FRA0 register is set to 1 (high speed on-chip oscillator on), fOCO can be used as timer RA. When the FRA00 bit is set to 1, fOCO40M can be used as timer RC. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. In this mode, stopping the XIN clock and high-speed on-chip oscillator, and setting the FMR47 bit in the FMR4 register to 1 (flash memory low consumption current read mode enabled) enables low consumption operation. To enter wait mode from low-speed clock mode, setting the VCA20 bit in the VCA2 register to 1 (internal power low consumption enabled) enables lower consumption current in wait mode. When enabling reduced internal power consumption using the VCA20 bit, follow Figure 10.14 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit. 10.5.1.3 High-Speed On-Chip Oscillator Mode The high-speed on-chip oscillator is used as the on-chip oscillator clock when the FRA00 bit in the FRA0 register is set to 1 (high-speed on-chip oscillator on) and the FRA01 bit in the FRA0 register is set to 1. The onchip oscillator divided by 1 (no division), 2, 4, 8, or 16 provides the CPU clock. Set the CM06 bit to 1 (divideby-8 mode) when transiting to high-speed clock mode. If the FRA00 bit is set to 1, fOCO40M can be used as timer RC. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. 10.5.1.4 Low-Speed On-Chip Oscillator Mode If the CM14 bit in the CM1 register is set to 0 (low-speed on-chip oscillator on) or the FRA01bit in the FRA0 register is set to 0, the low-speed on-chip oscillator provides the on-chip oscillator clock. The on-chip oscillator clock divided by 1 (no division), 2, 4, 8 or 16 provides the CPU clock. The on-chip oscillator clock is also the clock source for the peripheral function clocks. Set the CM06 bit to 1 (divide-by-8 mode) when transiting to high-speed clock mode. When the FRA00 bit is set to 1, fOCO40M can be used as timer RC. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. In this mode, stopping the XIN clock and high-speed on-chip oscillator, and setting the FMR47 bit in the FMR4 register to 1 (flash memory low consumption current read mode enabled) enables low consumption operation. To enter wait mode from low-speed on-chip oscillator mode, setting the VCA20 bit in the VCA2 register to 1 (internal power low consumption enabled) enables lower consumption current in wait mode. When enabling reduced internal power consumption using the VCA20 bit, follow Figure 10.14 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 95 of 453 R8C/26 Group, R8C/27 Group 10.5.2 10. Clock Generation Circuit Wait Mode Since the CPU clock stops in wait mode, the CPU, which operates using the CPU clock, and the watchdog timer, when count source protection mode is disabled, stop. The XIN clock, XCIN clock, and on-chip oscillator clock do not stop and the peripheral functions using these clocks continue operating. 10.5.2.1 Peripheral Function Clock Stop Function If the CM02 bit is set to 1 (peripheral function clock stops in wait mode), the f1, f2, f4, f8, and f32 clocks stop in wait mode. This reduces power consumption. 10.5.2.2 Entering Wait Mode The MCU enters wait mode when the WAIT instruction is executed. When the OCD2 bit in the OCD register is set to 1 (on-chip oscillator selected as system clock), set the OCD1 bit in the OCD register to 0 (oscillation stop detection interrupt disabled) before executing the WAIT instruction. If the MCU enters wait mode while the OCD1 bit is set to 1 (oscillation stop detection interrupt enabled), current consumption is not reduced because the CPU clock does not stop. 10.5.2.3 Pin Status in Wait Mode The I/O port is the status before wait mode was entered is maintained. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 96 of 453 R8C/26 Group, R8C/27 Group 10.5.2.4 10. Clock Generation Circuit Exiting Wait Mode The MCU exits wait mode by a reset or a peripheral function interrupt. The peripheral function interrupts are affected by the CM02 bit. When the CM02 bit is set to 0 (peripheral function clock does not stop in wait mode), all peripheral function interrupts can be used to exit wait mode. When the CM02 bit is set to 1 (peripheral function clock stops in wait mode), the peripheral functions using the peripheral function clock stop operating and the peripheral functions operated by external signals or on-chip oscillator clock can be used to exit wait mode. Table 10.3 lists Interrupts to Exit Wait Mode and Usage Conditions. Table 10.3 Interrupts to Exit Wait Mode and Usage Conditions Interrupt Serial interface interrupt CM02 = 0 Usable when operating with internal or external clock Clock synchronous serial I/O Usable in all modes with chip select interrupt / I2C bus interface interrupt Key input interrupt Usable A/D conversion interrupt Usable in one-shot mode Timer RA interrupt Usable in all modes Timer RB interrupt Timer RC interrupt Timer RE interrupt Usable in all modes Usable in all modes Usable in all modes INT interrupt Usable Voltage monitor 1 interrupt Voltage monitor 2 interrupt Oscillation stop detection interrupt Usable Usable Usable NOTE: 1. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 97 of 453 CM02 = 1 Usable when operating with external clock (Do not use) Usable (Do not use) Can be used if there is no filter in event counter mode. Usable by selecting fOCO or fC32(1) as count source. (Do not use) (Do not use) Usable when operating in real time clock mode(1) Usable (INT0, INT1, INT3 can be used if there is no filter.) Usable Usable (Do not use) R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Figure 10.13 shows the Time from Wait Mode to Interrupt Routine Execution. When using a peripheral function interrupt to exit wait mode, set up the following before executing the WAIT instruction. (1) Set the interrupt priority level in bits ILVL2 to ILVL0 in the interrupt control registers of the peripheral function interrupts to be used for exiting wait mode. Set bits ILVL2 to ILVL0 of the peripheral function interrupts that are not to be used for exiting wait mode to 000b (interrupt disabled). (2) Set the I flag to 1. (3) Operate the peripheral function to be used for exiting wait mode. When exiting by a peripheral function interrupt, the time (number of cycles) between interrupt request generation and interrupt routine execution is determined by the settings of the FMSTP bit in the FMR0 register, as described in Figure 10.13. The CPU clock, when exiting wait mode by a peripheral function interrupt, is the same clock as the CPU clock when the WAIT instruction is executed. FMR0 Register FMSTP Bit Time until Flash Memory is Activated (T1) Time until CPU Clock is Supplied (T2) 0 (flash memory operates) Period of system clock x 12 cycles + 30 s (max.) Period of CPU clock x 6 cycles 1 (flash memory stops) Period of system clock x 12 cycles Same as above Wait mode Time for Interrupt Sequence (T3) Period of CPU clock Following total time is the time x 20 cycles from wait mode until an interrupt routine is Same as above executed. T1 T2 T3 Flash memory activation sequence CPU clock restart sequence Interrupt sequence Interrupt request generated Figure 10.13 Time from Wait Mode to Interrupt Routine Execution Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Remarks Page 98 of 453 R8C/26 Group, R8C/27 Group 10.5.2.5 10. Clock Generation Circuit Reducing Internal Power Consumption Internal power consumption can be reduced by using low-speed clock mode (for N, D version only) or lowspeed on-chip oscillator mode. Figure 10.14 shows the Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit. When enabling reduced internal power consumption using the VCA20 bit, follow Figure 10.14 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit. Exit wait mode by interrupt Handling procedure of internal power low consumption enabled by VCA20 bit (Note 1) In interrupt routine Step (1) Enter low-speed clock mode or low-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) Step (7) (Wait until XIN clock oscillation stabilizes) Step (4) Enter wait mode(4) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (7) (Wait until XIN clock oscillation stabilizes) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode If it is necessary to start the high-speed clock or the high-speed on-chip oscillator in the interrupt routine, execute steps (5) to (7) in the interrupt routine. Interrupt handling Step (1) Enter low-speed clock mode or low-speed on-chip oscillator mode Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) If the high-speed clock or high-speed on-chip oscillator is started in the interrupt routine, execute steps (1) to (3) at the last of the interrupt routine. Interrupt handling completed NOTES: 1. Execute this routine to handle all interrupts generated in wait mode. However, this does not apply if it is not necessary to start the high-speed clock or high-speed on-chip oscillator during the interrupt routine. 2. Do not set the VCA20 bit to 0 with the instruction immediately after setting the VCA20 bit to 1. Also, do not do the opposite. 3. When the VCA20 bit is set to 1, do not set the CM10 bit to 1 (stop mode). 4. When entering wait mode, follow 10.7.2 Wait Mode. VCA20: Bit in VCA2 register Figure 10.14 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 99 of 453 R8C/26 Group, R8C/27 Group 10.5.3 10. Clock Generation Circuit Stop Mode Since the oscillator circuits stop in stop mode, the CPU clock and peripheral function clock stop and the CPU and peripheral functions that use these clocks stop operating. The least power required to operate the MCU is in stop mode. If the voltage applied to the VCC pin is VRAM or more, the contents of internal RAM is maintained. The peripheral functions clocked by external signals continue operating. Table 10.4 lists Interrupts to Exit Stop Mode and Usage Conditions. Table 10.4 Interrupts to Exit Stop Mode and Usage Conditions Interrupt Key input interrupt Usage Conditions - INT0, INT1, INT3 interrupt Timer RA interrupt Serial interface interrupt Voltage monitor 1 interrupt(1) Voltage monitor 2 interrupt Can be used if there is no filter When there is no filter and external pulse is counted in event counter mode When external clock is selected Usable in digital filter disabled mode (VW1C1 bit in VW1C register is set to 1) Usable in digital filter disabled mode (VW2C1 bit in VW2C register is set to 1) NOTE: 1. For N, D version only. 10.5.3.1 Entering Stop Mode The MCU enters stop mode when the CM10 bit in the CM1 register is set to 1 (all clocks stop). At the same time, the CM06 bit in the CM0 register is set to 1 (divide-by-8 mode), the CM03 bit in the CM0 register is set to 1 (XCIN clock oscillator circuit drive capacity high), and the CM15 bit in the CM1 register is set to 1 (XIN clock oscillator circuit drive capacity high). When using stop mode, set bits OCD1 to OCD0 to 00b before entering stop mode. 10.5.3.2 Pin Status in Stop Mode The status before wait mode was entered is maintained. However, when the CM01 bit in the CM0 register is set to 0 (XIN clock) and the CM13 bit in the CM1 register is set to 1 (XIN-XOUT pins), the XOUT(P4_7) pin is held "H". When the CM13 bit is set to 0 (input ports P4_6 and P4_7), the P4_7(XOUT pin) is held in input status. When the CM01 bit in the CM0 register is set to 1 (XCIN clock) and the CM04 bit in the CM0 register is set to 1 (XCIN clock oscillates), the XCOUT(P4_7) pin is held "H". When the CM04 bit is set to 0 (XIN clock stops), the P4_7(XOUT pin) is held in input status. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 100 of 453 R8C/26 Group, R8C/27 Group 10.5.3.3 10. Clock Generation Circuit Exiting Stop Mode The MCU exits stop mode by a reset or peripheral function interrupt. Figure 10.15 shows the Time from Stop Mode to Interrupt Routine Execution. When using a peripheral function interrupt to exit stop mode, set up the following before setting the CM10 bit to 1. (1) Set the interrupt priority level in bits ILVL2 to ILVL0 of the peripheral function interrupts to be used for exiting stop mode. Set bits ILVL2 to ILVL0 of the peripheral function interrupts that are not to be used for exiting stop mode to 000b (interrupt disabled). (2) Set the I flag to 1. (3) Operates the peripheral function to be used for exiting stop mode. When exiting by a peripheral function interrupt, the interrupt sequence is executed when an interrupt request is generated and the CPU clock supply is started. If the clock used immediately before stop mode is a system clock and stop mode is exited by a peripheral function interrupt, the CPU clock becomes the previous system clock divided by 8. FMR0 Register Stop mode FMSTP Bit Time until Flash Memory is Activated (T2) Time until CPU Clock is Supplied (T3) 0 (flash memory operates) Period of system clock x 12 cycles + 30 s (max.) Period of CPU clock x 6 cycles 1 (flash memory stops) Period of system clock x 12 cycles Same as above Time for Interrupt Sequence (T4) Period of CPU clock Following total time of T0 to T4 is x 20 cycles the time from stop mode until an interrupt handling Same as above is executed. T0 T1 T2 T3 T4 Internal power stability time Oscillation time of CPU clock source used immediately before stop mode Flash memory activation sequence CPU clock restart sequence Interrupt sequence 150 s Interrupt (max.) request generated Figure 10.15 Time from Stop Mode to Interrupt Routine Execution Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 101 of 453 Remarks R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Figure 10.16 shows the State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 0 (XIN clock)). Figure 10.17 shows the State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 1 (XCIN clock)). State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 0 (XIN clock)) Reset Standard operating mode Low-speed on-chip oscillator mode CM14 = 0 OCD2 = 1 FRA01 = 0 CM14 = 0 OCD2 = 1 FRA01 = 0 CM05 = 0 CM13 = 1 OCD2 = 0 High-speed clock mode CM14 = 0 FRA01 = 0 CM05 = 0 CM13 = 1 OCD2 = 0 FRA00 = 1 FRA01 = 1 OCD2 = 1 FRA00 = 1 FRA01 = 1 CM05 = 0 CM13 = 1 OCD2 = 0 High-speed on-chip oscillator mode OCD2 = 1 FRA00 = 1 FRA01 = 1 Interrupt WAIT instruction CM10 = 1 Interrupt Wait mode Stop mode CPU operation stops All oscillators stop CM05: Bit in CM0 register CM13, CM14: Bits in CM1 register OCD2: Bit in OCD register FRA00, FRA01: Bits in FRA0 register Figure 10.16 State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 0 (XIN clock)) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 102 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 1 (XCIN clock)) (For N, D version only) Reset Standard operating mode Low-speed on-chip oscillator mode CM14 = 0 OCD2 = 1 FRA01 = 0 CM04 = 1 OCD2 = 0 CM14 = 0 OCD2 = 1 FRA01 = 0 CM14 = 0 FRA01 = 0 Low-speed clock mode FRA00 = 1 FRA01 = 1 CM04 = 1 OCD2 = 0 CM04 = 1 OCD2 = 0 High-speed on-chip oscillator mode OCD2 = 1 FRA00 = 1 FRA01 = 1 OCD2 = 1 FRA00 = 1 FRA01 = 1 Interrupt WAIT instruction CM10 = 1 Interrupt Wait mode Stop mode CPU operation stops All oscillators stop CM04: Bit in CM0 register CM14: Bit in CM1 register OCD2: Bit in OCD register FRA00, FRA01: Bits in FRA0 register Figure 10.17 State Transitions in Power Control Mode (When the CM01 bit in the CM0 register is set to 1 (XCIN clock)) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 103 of 453 R8C/26 Group, R8C/27 Group 10.6 10. Clock Generation Circuit Oscillation Stop Detection Function The oscillation stop detection function detects the stop of the XIN clock oscillating circuit. The oscillation stop detection function can be enabled and disabled by the OCD0 bit in the OCD register. Table 10.5 lists the Specifications of Oscillation Stop Detection Function. When the XIN clock is the CPU clock source and bits OCD1 to OCD0 are set to 11b, the system is placed in the following state if the XIN clock stops. * OCD2 bit in OCD register = 1 (on-chip oscillator clock selected) * OCD3 bit in OCD register = 1 (XIN clock stops) * CM14 bit in CM1 register = 0 (low-speed on-chip oscillator oscillates) * Oscillation stop detection interrupt request is generated. Table 10.5 Specifications of Oscillation Stop Detection Function Item Oscillation stop detection clock and frequency bandwidth Enabled condition for oscillation stop detection function Operation at oscillation stop detection 10.6.1 Specification f(XIN) 2 MHz Set bits OCD1 to OCD0 to 11b Oscillation stop detection interrupt is generated How to Use Oscillation Stop Detection Function * The oscillation stop detection interrupt shares a vector with the voltage monitor 1 interrupt, the voltage monitor 2 interrupt, and the watchdog timer interrupt. When using the oscillation stop detection interrupt and watchdog timer interrupt, the interrupt source needs to be determined. Table 10.6 lists the Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, and Voltage Monitor 2 Interrupts. Figure 10.19 shows the Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt (N, D Version). Figure 10.20 shows the Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt (J, K Version). * When the XIN clock restarts after oscillation stop, switch the XIN clock to the clock source of the CPU clock and peripheral functions by a program. Figure 10.18 shows the Procedure for Switching Clock Source from Low-Speed On-Chip Oscillator to XIN Clock. * To enter wait mode while using the oscillation stop detection function, set the CM02 bit to 0 (peripheral function clock does not stop in wait mode). * Since the oscillation stop detection function is a function for cases where the XIN clock is stopped by an external cause, set bits OCD1 to OCD0 to 00b when the XIN clock stops or is started by a program, (stop mode is selected or the CM05 bit is changed). * This function cannot be used when the XIN clock frequency is 2 MHz or below. In this case, set bits OCD1 to OCD0 to 00b. * To use the low-speed on-chip oscillator clock for the CPU clock and clock sources of peripheral functions after detecting the oscillation stop, set the FRA01 bit in the FRA0 register to 0 (low-speed on-chip oscillator selected) and bits OCD1 to OCD0 to 11b. To use the high-speed on-chip oscillator clock for the CPU clock and clock sources of peripheral functions after detecting the oscillation stop, set the FRA00 bit to 1 (high-speed on-chip oscillator on) and the FRA01 bit to 1 (high-speed on-chip oscillator selected) and then set bits OCD1 to OCD0 to 11b. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 104 of 453 R8C/26 Group, R8C/27 Group Table 10.6 10. Clock Generation Circuit Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, and Voltage Monitor 2 Interrupts Generated Interrupt Source Bit Showing Interrupt Cause Oscillation stop detection (a) OCD3 bit in OCD register = 1 ((a) or (b)) (b) OCD1 to OCD0 bits in OCD register = 11b and OCD2 bit = 1 Watchdog timer VW2C3 bit in VW2C register = 1 VW1C2 bit in VW1C register = 1 Voltage monitor 1(1) Voltage monitor 2 VW2C2 bit in VW2C register = 1 NOTE: 1. For N, D version only. Switch to XIN clock NO Multiple confirmations that OCD3 bit is set to 0 (XIN clock oscillates) ? YES Set OCD1 to OCD0 bits to 00b Set OCD2 bit to 0 (select XIN clock) End OCD3 to OCD0: Bits in OCD register Figure 10.18 Procedure for Switching Clock Source from Low-Speed On-Chip Oscillator to XIN Clock Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 105 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Interrupt sources judgement OCD3 = 1 ? (XIN clock stopped) NO YES OCD1 = 1 (oscillation stop detection interrupt enabled) and OCD2 = 1 (on-chip oscillator clock selected as system clock) ? NO YES VW2C3 = 1 ? (Watchdog timer underflow) NO YES VW2C2 = 1 ? (passing Vdet2) NO YES Set OCD1 bit to 0 (oscillation stop detection interrupt disabled). (1) To oscillation stop detection interrupt routine To watchdog timer interrupt routine To voltage monitor 2 interrupt routine To voltage monitor 1 interrupt routine NOTE: 1. This disables multiple oscillation stop detection interrupts. OCD1 to OCD3: Bits in OCD register VW2C2, VW2C3: Bits in VW2C register Figure 10.19 Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt (N, D Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 106 of 453 R8C/26 Group, R8C/27 Group 10. Clock Generation Circuit Interrupt sources judgement NO OCD3 = 1 ? (XIN clock stopped) YES OCD1 = 1 (oscillation stop detection interrupt enabled) and OCD2 = 1 (on-chip oscillator clock selected as system clock) ? NO YES VW2C3 = 1 ? (Watchdog timer underflow) NO YES Set OCD1 bit to 0 (oscillation stop detection interrupt disabled).(1) To oscillation stop detection interrupt routine To watchdog timer interrupt routine To voltage monitor 2 interrupt routine NOTE: 1. This disables multiple oscillation stop detection interrupts. OCD1 to OCD3: Bits in OCD register VW2C3: Bit in VW2C register Figure 10.20 Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt (J, K Version) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 107 of 453 R8C/26 Group, R8C/27 Group 10.7 10. Clock Generation Circuit Notes on Clock Generation Circuit 10.7.1 Stop Mode When entering stop mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and the CM10 bit in the CM1 register to 1 (stop mode). An instruction queue pre-reads 4 bytes from the instruction which sets the CM10 bit to 1 (stop mode) and the program stops. Insert at least 4 NOP instructions following the JMP.B instruction after the instruction which sets the CM10 bit to 1. * Program example to enter stop mode BCLR BSET FSET BSET JMP.B LABEL_001 : NOP NOP NOP NOP 10.7.2 1,FMR0 0,PRCR I 0,CM1 LABEL_001 ; CPU rewrite mode disabled ; Protect disabled ; Enable interrupt ; Stop mode Wait Mode When entering wait mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and execute the WAIT instruction. An instruction queue pre-reads 4 bytes from the WAIT instruction and the program stops. Insert at least 4 NOP instructions after the WAIT instruction. * Program example to execute the WAIT instruction BCLR 1,FMR0 FSET I WAIT NOP NOP NOP NOP 10.7.3 ; CPU rewrite mode disabled ; Enable interrupt ; Wait mode Oscillation Stop Detection Function Since the oscillation stop detection function cannot be used if the XIN clock frequency is 2 MHz or below, set bits OCD1 to OCD0 to 00b. 10.7.4 Oscillation Circuit Constants Ask the manufacturer of the oscillator to specify the best oscillation circuit constants for your system. To use this MCU with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 108 of 453 R8C/26 Group, R8C/27 Group 11. Protection 11. Protection The protection function protects important registers from being easily overwritten when a program runs out of control. Figure 11.1 shows the PRCR Register. The registers protected by the PRCR register are listed below. * Registers protected by PRC0 bit: Registers CM0, CM1, OCD, FRA0, FRA1, and FRA2 * Registers protected by PRC1 bit: Registers PM0 and PM1 * Registers protected by PRC2 bit: PD0 register * Registers protected by PRC3 bit: Registers VCA2, VW0C, VW1C, and VW2C Protect Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol PRCR Bit Symbol Address 000Ah Bit Name Protect bit 0 PRC0 Protect bit 1 PRC1 Protect bit 2 PRC2 Protect bit 3 PRC3 After Reset 00h Function Writing to registers CM0, CM1, OCD, FRA0, FRA1, and FRA2 is enabled. 0 : Disables w riting 1 : Enables w riting RW RW Writing to registers PM0 and PM1 is enabled. 0 : Disables w riting 1 : Enables w riting RW Writing to the PD0 register is enabled. 0 : Disables w riting 1 : Enables w riting(1) RW Writing to registers VCA2, VW0C, VW1C, and VW2C is enabled. 0 : Disables w riting 1 : Enables w riting RW -- (b5-b4) Reserved bits Set to 0. -- (b7-b6) Reserved bits When read, the content is 0. RW RO NOTE: 1. This bit is set to 0 after w riting 1 to the PRC2 bit and executing a w rite to any address. Since the other bits are not set to 0, set them to 0 by a program. Figure 11.1 PRCR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 109 of 453 R8C/26 Group, R8C/27 Group 12. Interrupts 12. Interrupts 12.1 Interrupt Overview 12.1.1 Types of Interrupts Figure 12.1 shows the Types of Interrupts. Software (non-maskable interrupts) Interrupts Special (non-maskable interrupts) Hardware Undefined instruction (UND instruction) Overflow (INTO instruction) BRK instruction INT instruction Watchdog timer Oscillation stop detection Voltage monitor 1 Voltage monitor 2 Single step(2) Address break(2) Address match Peripheral functions(1) (maskable interrupts) NOTES: 1. Peripheral function interrupts in the MCU are used to generate peripheral interrupts. 2. Do not use this interrupt. This is for use with development tools only. Figure 12.1 Types of Interrupts * Maskable Interrupts: * Non-Maskable Interrupts: Rev.2.10 Sep 26, 2008 REJ09B0278-0210 The interrupt enable flag (I flag) enables or disables these interrupts. The interrupt priority order can be changed based on the interrupt priority level. The interrupt enable flag (I flag) does not enable or disable these interrupts. The interrupt priority order cannot be changed based on interrupt priority level. Page 110 of 453 R8C/26 Group, R8C/27 Group 12.1.2 12. Interrupts Software Interrupts A software interrupt is generated when an instruction is executed. Software interrupts are non-maskable. 12.1.2.1 Undefined Instruction Interrupt The undefined instruction interrupt is generated when the UND instruction is executed. 12.1.2.2 Overflow Interrupt The overflow interrupt is generated when the O flag is set to 1 (arithmetic operation overflow) and the INTO instruction is executed. Instructions that set the O flag are: ABS, ADC, ADCF, ADD, CMP, DIV, DIVU, DIVX, NEG, RMPA, SBB, SHA, and SUB. 12.1.2.3 BRK Interrupt A BRK interrupt is generated when the BRK instruction is executed. 12.1.2.4 INT Instruction Interrupt An INT instruction interrupt is generated when the INT instruction is executed. The INT instruction can select software interrupt numbers 0 to 63. Software interrupt numbers 3 to 31 are assigned to the peripheral function interrupt. Therefore, the MCU executes the same interrupt routine when the INT instruction is executed as when a peripheral function interrupt is generated. For software interrupt numbers 0 to 31, the U flag is saved to the stack during instruction execution and the U flag is set to 0 (ISP selected) before the interrupt sequence is executed. The U flag is restored from the stack when returning from the interrupt routine. For software interrupt numbers 32 to 63, the U flag does not change state during instruction execution, and the selected SP is used. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 111 of 453 R8C/26 Group, R8C/27 Group 12.1.3 12. Interrupts Special Interrupts Special interrupts are non-maskable. 12.1.3.1 Watchdog Timer Interrupt The watchdog timer interrupt is generated by the watchdog timer. For details of the watchdog timer, refer to 13. Watchdog Timer. 12.1.3.2 Oscillation Stop Detection Interrupt The oscillation stop detection interrupt is generated by the oscillation stop detection function. For details of the oscillation stop detection function, refer to 10. Clock Generation Circuit. 12.1.3.3 Voltage Monitor 1 Interrupt (For N, D Version Only) The voltage monitor 1 interrupt is generated by the voltage detection circuit. For details of the voltage detection circuit, refer to 6. Voltage Detection Circuit. 12.1.3.4 Voltage Monitor 2 Interrupt The voltage monitor 2 interrupt is generated by the voltage detection circuit. For details of the voltage detection circuit, refer to 6. Voltage Detection Circuit. 12.1.3.5 Single-Step Interrupt, and Address Break Interrupt Do not use these interrupts. They are for use by development tools only. 12.1.3.6 Address Match Interrupt The address match interrupt is generated immediately before executing an instruction that is stored at an address indicated by registers RMAD0 to RMAD1 when the AIER0 or AIER1 bit in the AIER register is set to 1 (address match interrupt enable). For details of the address match interrupt, refer to 12.4 Address Match Interrupt. 12.1.4 Peripheral Function Interrupt The peripheral function interrupt is generated by the internal peripheral function of the MCU and is a maskable interrupt. Refer to Table 12.2 Relocatable Vector Tables for sources of the peripheral function interrupt. For details of peripheral functions, refer to the descriptions of individual peripheral functions. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 112 of 453 R8C/26 Group, R8C/27 Group 12.1.5 12. Interrupts Interrupts and Interrupt Vectors There are 4 bytes in each vector. Set the starting address of an interrupt routine in each interrupt vector. When an interrupt request is acknowledged, the CPU branches to the address set in the corresponding interrupt vector. Figure 12.2 shows an Interrupt Vector. MSB LSB Vector address (L) Low address Mid address Vector address (H) Figure 12.2 12.1.5.1 0000 High address 0000 0000 Interrupt Vector Fixed Vector Tables The fixed vector tables are allocated addresses 0FFDCh to 0FFFFh. Table 12.1 lists the Fixed Vector Tables. The vector addresses (H) of fixed vectors are used by the ID code check function. For details, refer to 19.3 Functions to Prevent Rewriting of Flash Memory. Table 12.1 Fixed Vector Tables Interrupt Source Undefined instruction Overflow BRK instruction Address match Single step(1) Watchdog timer, Oscillation stop detection, Voltage monitor 1(2), Voltage monitor 2 Address break(1) (Reserved) Reset Vector Addresses Remarks Reference Address (L) to (H) 0FFDCh to 0FFDFh Interrupt on UND R8C/Tiny Series Software instruction Manual 0FFE0h to 0FFE3h Interrupt on INTO instruction 0FFE4h to 0FFE7h If the content of address 0FFE7h is FFh, program execution starts from the address shown by the vector in the relocatable vector table. 0FFE8h to 0FFEBh 12.4 Address Match Interrupt 0FFECh to 0FFEFh 0FFF0h to 0FFF3h 13. Watchdog Timer 10. Clock Generation Circuit 6. Voltage Detection Circuit 0FFF4h to 0FFF7h 0FFF8h to 0FFFBh 0FFFCh to 0FFFFh 5. Resets NOTES: 1. Do not use these interrupts. They are for use by development tools only. 2. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 113 of 453 R8C/26 Group, R8C/27 Group 12.1.5.2 12. Interrupts Relocatable Vector Tables The relocatable vector tables occupy 256 bytes beginning from the starting address set in the INTB register. Table 12.2 lists the Relocatable Vector Tables. Table 12.2 Relocatable Vector Tables Vector Addresses(1) Address (L) to Address (H) Interrupt Source BRK instruction(3) (Reserved) (Reserved) Timer RC (Reserved) Timer RE (Reserved) Key input A/D Clock synchronous serial I/O with chip select / I2C bus interface(2) (Reserved) UART0 transmit UART0 receive UART1 transmit UART1 receive (Reserved) Timer RA (Reserved) Timer RB +0 to +3 (0000h to 0003h) +28 to +31 (001Ch to 001Fh) +40 to +43 (0028h to 002Bh) +52 to +55 (0034h to 0037h) +56 to +59 (0038h to 003Bh) +60 to +63 (003Ch to 003Fh) Software Interrupt Control Interrupt Reference Register Number 0 - R8C/Tiny Series Software Manual 1 to 2 - - 3 to 6 - - 7 TRCIC 14.3 Timer RC 8 to 9 - - 10 TREIC 14.4 Timer RE 11 to 12 - - 13 KUPIC 12.3 Key Input Interrupt 14 ADIC 18. A/D Converter 15 SSUIC/IICIC 16.2 Clock Synchronous Serial I/O with Chip Select (SSU), 16.3 I2C bus Interface +96 to +99 (0060h to 0063h) +100 to +103 (0064h to 0067h) 16 17 18 19 20 21 22 23 24 25 - S0TIC S0RIC S1TIC S1RIC - TRAIC - TRBIC INT1IC INT3 (Reserved) (Reserved) +104 to +107 (0068h to 006Bh) 26 INT3IC INT0 (Reserved) (Reserved) +116 to +119 (0074h to 0077h) 27 28 29 - - INT0IC INT1 Software interrupt(3) +68 to +71 (0044h to 0047h) +72 to +75 (0048h to 004Bh) +76 to +79 (004Ch to 004Fh) +80 to +83 (0050h to 0053h) +88 to +91 (0058h to 005Bh) 30 31 +128 to +131 (0080h to 0083h) to 32 to 63 +252 to +255 (00FCh to 00FFh) NOTES: 1. These addresses are relative to those in the INTB register. 2. The IICSEL bit in the PMR register switches functions. 3. The I flag does not disable these interrupts. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 114 of 453 - - - - 15. Serial Interface - 14.1 Timer RA - 14.2 Timer RB 12.2 INT Interrupt - - 12.2 INT Interrupt - - R8C/Tiny Series Software Manual R8C/26 Group, R8C/27 Group 12.1.6 12. Interrupts Interrupt Control The following describes enabling and disabling the maskable interrupts and setting the priority for acknowledgement. The explanation does not apply to nonmaskable interrupts. Use the I flag in the FLG register, IPL, and bits ILVL2 to ILVL0 in each interrupt control register to enable or disable maskable interrupts. Whether an interrupt is requested is indicated by the IR bit in each interrupt control register. Figure 12.3 shows the Interrupt Control Register, Figure 12.4 shows Registers TRCIC and SSUIC/IICIC and Figure 12.5 shows the INTiIC Register (i=0, 1, 3). Interrupt Control Register(2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TREIC KUPIC ADIC S0TIC S0RIC S1TIC S1RIC TRAIC TRBIC Bit Symbol Address 004Ah 004Dh 004Eh 0051h 0052h 0053h 0054h 0056h After Reset XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b 0058h XXXXX000b Bit Name Interrupt priority level select bits 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 ILVL0 ILVL1 ILVL2 IR -- (b7-b4) Function Interrupt request bit RW b2 b1 b0 0 : Requests no interrupt 1 : Requests interrupt Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW RW RW RW(1) -- NOTES: 1. Only 0 can be w ritten to the IR bit. Do not w rite 1. 2. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for its register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents. Figure 12.3 Interrupt Control Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 115 of 453 R8C/26 Group, R8C/27 Group 12. Interrupts Interrupt Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCIC SSUIC/IICIC(2) Bit Symbol Address 0047h After Reset XXXXX000b 004Fh XXXXX000b Bit Name Interrupt priority level select bits ILVL0 ILVL1 ILVL2 IR -- (b7-b4) Interrupt request bit Function RW b2 b1 b0 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 RW 0 : Requests no interrupt 1 : Requests interrupt RO Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW RW -- NOTES: 1. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for the register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents. 2. The IICSEL bit in the PMR register sw itches functions. Figure 12.4 Registers TRCIC and SSUIC/IICIC Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 116 of 453 R8C/26 Group, R8C/27 Group 12. Interrupts INTi Interrupt Control Register (i=0, 1, 3)(2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol INT1IC INT3IC Address 0059h 005Ah After Reset XX00X000b XX00X000b INT0IC 005Dh XX00X000b Bit Symbol Bit Name Interrupt priority level select bits 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 ILVL0 ILVL1 ILVL2 IR POL -- (b5) -- (b7-b6) Function RW b2 b1 b0 RW RW RW Interrupt request bit 0 : Requests no interrupt 1 : Requests interrupt RW(1) Polarity sw itch bit(4) 0 : Selects falling edge 1 : Selects rising edge(3) RW Reserved bit Set to 0. Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW -- NOTES: 1. Only 0 can be w ritten to the IR bit. (Do not w rite 1.) 2. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for the register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents. 3. If the INTiPL bit in the INTEN register is set to 1 (both edges), set the POL bit to 0 (selects falling edge). 4. The IR bit may be set to 1 (requests interrupt) w hen the POL bit is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.5 INTiIC Register (i=0, 1, 3) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 117 of 453 R8C/26 Group, R8C/27 Group 12.1.6.1 12. Interrupts I Flag The I flag enables or disables maskable interrupts. Setting the I flag to 1 (enabled) enables maskable interrupts. Setting the I flag to 0 (disabled) disables all maskable interrupts. 12.1.6.2 IR Bit The IR bit is set to 1 (interrupt requested) when an interrupt request is generated. Then, when the interrupt request is acknowledged and the CPU branches to the corresponding interrupt vector, the IR bit is set to 0 (= interrupt not requested). The IR bit can be set to 0 by a program. Do not write 1 to this bit. However, the IR bit operations of the timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt and the I 2 C bus Interface Interrupt are different. Refer to 12.5 Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupts, and I2C bus Interface Interrupt (Interrupts with Multiple Interrupt Request Sources). 12.1.6.3 ILVL2 to ILVL0 Bits and IPL Interrupt priority levels can be set using bits ILVL2 to ILVL0. Table 12.3 lists the Settings of Interrupt Priority Levels and Table 12.4 lists the Interrupt Priority Levels Enabled by IPL. The following are conditions under which an interrupt is acknowledged: * I flag = 1 * IR bit = 1 * Interrupt priority level > IPL The I flag, IR bit, bits ILVL2 to ILVL0, and IPL are independent of each other. They do not affect one another. Table 12.3 Settings of Interrupt Priority Levels ILVL2 to ILVL0 Bits 000b 001b 010b 011b 100b 101b 110b 111b Interrupt Priority Level Priority Order - Level 0 (interrupt disabled) Level 1 Low Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 High Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 118 of 453 Table 12.4 IPL 000b 001b 010b 011b 100b 101b 110b 111b Interrupt Priority Levels Enabled by IPL Enabled Interrupt Priority Levels Interrupt level 1 and above Interrupt level 2 and above Interrupt level 3 and above Interrupt level 4 and above Interrupt level 5 and above Interrupt level 6 and above Interrupt level 7 and above All maskable interrupts are disabled R8C/26 Group, R8C/27 Group 12.1.6.4 12. Interrupts Interrupt Sequence An interrupt sequence is performed between an interrupt request acknowledgement and interrupt routine execution. When an interrupt request is generated while an instruction is being executed, the CPU determines its interrupt priority level after the instruction is completed. The CPU starts the interrupt sequence from the following cycle. However, for the SMOVB, SMOVF, SSTR, or RMPA instructions, if an interrupt request is generated while the instruction is being executed, the MCU suspends the instruction to start the interrupt sequence. The interrupt sequence is performed as indicated below. Figure 12.6 shows the Time Required for Executing Interrupt Sequence. (1) The CPU gets interrupt information (interrupt number and interrupt request level) by reading address 00000h. The IR bit for the corresponding interrupt is set to 0 (interrupt not requested).(2) (2) The FLG register is saved to a temporary register(1) in the CPU immediately before entering the interrupt sequence. (3) The I, D and U flags in the FLG register are set as follows: The I flag is set to 0 (interrupts disabled). The D flag is set to 0 (single-step interrupt disabled). The U flag is set to 0 (ISP selected). However, the U flag does not change state if an INT instruction for software interrupt number 32 to 63 is executed. (4) The CPU's internal temporary register(1) is saved to the stack. (5) The PC is saved to the stack. (6) The interrupt priority level of the acknowledged interrupt is set in the IPL. (7) The starting address of the interrupt routine set in the interrupt vector is stored in the PC. After the interrupt sequence is completed, instructions are executed from the starting address of the interrupt routine. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CPU Clock Address Bus Data Bus Address 0000h Undefined Interrupt information RD Undefined SP-2 SP-1 SP-4 SP-2 SP-1 SP-4 contents contents contents SP-3 SP-3 contents VEC VEC contents VEC+1 VEC+1 contents VEC+2 PC VEC+2 contents Undefined WR The indeterminate state depends on the instruction queue buffer. A read cycle occurs when the instruction queue buffer is ready to acknowledge instructions. Figure 12.6 Time Required for Executing Interrupt Sequence NOTES: 1. This register cannot be used by user. 2. Refer to 12.5 Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupts, and I2C bus Interface Interrupt (Interrupts with Multiple Interrupt Request Sources) for the IR bit operations of the timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt, and the I2C bus Interface Interrupt. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 119 of 453 R8C/26 Group, R8C/27 Group 12.1.6.5 12. Interrupts Interrupt Response Time Figure 12.7 shows the Interrupt Response Time. The interrupt response time is the period between an interrupt request generation and the execution of the first instruction in the interrupt routine. The interrupt response time includes the period between interrupt request generation and the completion of execution of the instruction (refer to (a) in Figure 12.7) and the period required to perform the interrupt sequence (20 cycles, refer to (b) in Figure 12.7). Interrupt request is generated. Interrupt request is acknowledged. Time Instruction (a) Instruction in interrupt routine Interrupt sequence 20 cycles (b) Interrupt response time (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (no wait and when the register is set as the divisor) (b) 21 cycles for address match and single-step interrupts. Figure 12.7 12.1.6.6 Interrupt Response Time IPL Change when Interrupt Request is Acknowledged When an interrupt request of a maskable interrupt is acknowledged, the interrupt priority level of the acknowledged interrupt is set in the IPL. When a software interrupt or special interrupt request is acknowledged, the level listed in Table 12.5 is set in the IPL. Table 12.5 lists the IPL Value When Software or Special Interrupt Is Acknowledged. Table 12.5 IPL Value When Software or Special Interrupt Is Acknowledged Interrupt Source Watchdog timer, oscillation stop detection, voltage monitor voltage monitor 2, address break Software, address match, single-step NOTE: 1. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 120 of 453 1(1), Value Set in IPL 7 Not changed R8C/26 Group, R8C/27 Group 12.1.6.7 12. Interrupts Saving a Register In the interrupt sequence, the FLG register and PC are saved to the stack. After an extended 16 bits, 4 high-order bits in the PC and 4 high-order (IPL) and 8 low-order bits in the FLG register, are saved to the stack, the 16 low-order bits in the PC are saved. Figure 12.8 shows the Stack State Before and After Acknowledgement of Interrupt Request. The other necessary registers are saved by a program at the beginning of the interrupt routine. The PUSHM instruction can save several registers in the register bank being currently used(1) with a single instruction. NOTE: 1. Selectable from registers R0, R1, R2, R3, A0, A1, SB, and FB. Stack Address Stack Address MSB LSB MSB LSB m-4 m-4 PCL m-3 m-3 PCM m-2 m-2 FLGL m-1 m-1 m Previous stack contents m+1 Previous stack contents [SP] SP value before interrupt is generated m m+1 Stack state before interrupt request is acknowledged FLGH [SP] New SP value PCH Previous stack contents Previous stack contents PCH PCM PCL FLGH FLGL : 4 High-order bits of PC : 8 Middle-order bits of PC : 8 Low-order bits of PC : 4 High-order bits of FLG : 8 Low-order bits of FLG Stack state after interrupt request is acknowledged NOTE: 1. When executing software number 32 to 63 INT instructions, this SP is specified by the U flag. Otherwise it is ISP. Figure 12.8 Stack State Before and After Acknowledgement of Interrupt Request The register saving operation, which is performed as part of the interrupt sequence, saved in 8 bits at a time in four steps. Figure 12.9 shows the Register Saving Operation. Stack Address Sequence in which order registers are saved [SP]-5 [SP]-4 PCL (3) [SP]-3 PCM (4) [SP]-2 FLGL (1) Saved, 8 bits at a time [SP]-1 FLGH PCH (2) [SP] Completed saving registers in four operations. PCH PCM PCL FLGH FLGL NOTE: 1. [SP] indicates the initial value of the SP when an interrupt request is acknowledged. After registers are saved, the SP content is [SP] minus 4. When executing software number 32 to 63 INT instructions, this SP is specified by the U flag. Otherwise it is ISP. Figure 12.9 Register Saving Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 121 of 453 : 4 High-order bits of PC : 8 Middle-order bits of PC : 8 Low-order bits of PC : 4 High-order bits of FLG : 8 Low-order bits of FLG R8C/26 Group, R8C/27 Group 12.1.6.8 12. Interrupts Returning from an Interrupt Routine When the REIT instruction is executed at the end of an interrupt routine, the FLG register and PC, which have been saved to the stack, are automatically restored. The program, that was running before the interrupt request was acknowledged, starts running again. Restore registers saved by a program in an interrupt routine using the POPM instruction or others before executing the REIT instruction. 12.1.6.9 Interrupt Priority If two or more interrupt requests are generated while a single instruction is being executed, the interrupt with the higher priority is acknowledged. Set bits ILVL2 to ILVL0 to select the desired priority level for maskable interrupts (peripheral functions). However, if two or more maskable interrupts have the same priority level, their interrupt priority is resolved by hardware, and the higher priority interrupts acknowledged. The priority levels of special interrupts, such as reset (reset has the highest priority) and watchdog timer, are set by hardware. Figure 12.10 shows the Priority Levels of Hardware Interrupts. The interrupt priority does not affect software interrupts. The MCU jumps to the interrupt routine when the instruction is executed. Reset High Address break Watchdog timer Oscillation stop detection Voltage monitor 1 (1) Voltage monitor 2 Peripheral function Single step Address match NOTE: 1. For N, D version only. Figure 12.10 Priority Levels of Hardware Interrupts Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 122 of 453 Low R8C/26 Group, R8C/27 Group 12. Interrupts 12.1.6.10 Interrupt Priority Judgement Circuit The interrupt priority judgement circuit selects the highest priority interrupt, as shown in Figure 12.11. Priority level of interrupt Level 0 (default value) Highest INT3 Timer RB Timer RA INT0 INT1 Timer RC Priority of peripheral function interrupts (if priority levels are same) UART1 receive UART0 receive A/D conversion Timer RE UART1 transmit UART0 transmit SSU / I2C bus(1) Key input IPL Lowest Interrupt request level judgment output signal I flag Address match Watchdog timer Oscillation stop detection Voltage monitor 1(2) Voltage monitor 2 NOTES: 1. The IICSEL bit in the PMR register switches functions. 2. For N, D version only. Figure 12.11 Interrupt Priority Level Judgement Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 123 of 453 Interrupt request acknowledged R8C/26 Group, R8C/27 Group 12.2 12. Interrupts INT Interrupt 12.2.1 INTi Interrupt (i = 0, 1, 3) The INTi interrupt is generated by an INTi input. When using the INTi interrupt, the INTiEN bit in the INTEN register is set to 1 (enable). The edge polarity is selected using the INTiPL bit in the INTEN register and the POL bit in the INTiIC register. Inputs can be passed through a digital filter with three different sampling clocks. Table 12.6 lists the Pin Configuration of INT Interrupt. Figure 12.12 shows the INTEN Register. Figure 12.13 shows the INTF Register. Pin Configuration of INT Interrupt Table 12.6 Pin name Input/Output Function INT0 (P4_5) Input INT0 interrupt input, Timer RB external trigger input, Timer RC pulse output forced cutoff input INT1 (P1_5, P1_7, or P3_6)(1) Input INT1 interrupt input INT3 (P3_3) Input INT3 interrupt input NOTE: 1. The INT1 pin is selected by the INT1SEL bit in the PMR register and the TIOSEL bit in the TRAIOC register. Refer to 7. Programmable I/O Ports for details. External Input Enable Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol INTEN Bit Symbol INT0EN Address 00F9h Bit Name _____ INT0 input enable bit RW 0 : One edge 1 : Both edges RW 0 : Disable 1 : Enable RW INT1 input polarity select bit(1,2) 0 : One edge 1 : Both edges RW Reserved bits Set to 0. INT0 input polarity select bit(1,2) _____ INT1EN INT1 input enable bit _____ INT1PL -- (b5-b4) _____ INT3EN INT3 input enable bit _____ INT3PL RW 0 : Disable 1 : Enable _____ INT0PL After Reset 00h Function INT3 input polarity select bit(1,2) RW 0 : Disable 1 : Enable RW 0 : One edge 1 : Both edges RW NOTES: 1. When setting the INTiPL bit (i = 0 to 3) to 1 (both edges), set the POL bit in the INTiIC register to 0 (selects falling edge). 2. The IR bit in the INTiIC register may be set to 1 (requests interrupt) w hen the INTiPL bit is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.12 INTEN Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 124 of 453 R8C/26 Group, R8C/27 Group 12. Interrupts ______ INT0 Input Filter Select Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol INTF Bit Symbol Address 00FAh Bit Name _____ INT0F0 INT0 input filter select bits INT0F1 _____ INT1F0 INT1 input filter select bits INT1F1 -- (b5-b4) INT3F0 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling b7 b6 Page 125 of 453 RW RW b3 b2 _____ INTF Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Set to 0. INT3 input filter select bits RW b1 b0 Reserved bits INT3F1 Figure 12.13 After Reset 00h Function 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling RW RW RW RW RW R8C/26 Group, R8C/27 Group 12.2.2 12. Interrupts INTi Input Filter (i = 0, 1, 3) The INTi input contains a digital filter. The sampling clock is selected by bits INTiF1 to INTiF0 in the INTF register. The IR bit in the INTiIC register is set to 1 (interrupt requested) when the INTi level is sampled for every sampling clock and the sampled input level matches three times. Figure 12.14 shows the Configuration of INTi Input Filter. Figure 12.15 shows an Operating Example of INTi Input Filter. INTiF1 to INTiF0 f1 f8 f32 INTi Port direction register(1) = 01b = 10b Sampling clock = 11b INTiEN Digital filter (input level matches 3x) Other than INTiF1 to INTiF0 = 00b = 00b INTiF0, INTiF1: Bits in INTF register INTiEN, INTiPL: Bits in INTEN register i = 0, 1, 3 INTi interrupt INTiPL = 0 Both edges detection INTiPL = 1 circuit NOTE: 1. INT0: Port P4_5 direction register INT1: Port P1_5 direction register when using the P1_5 pin Port P1_7 direction register when using the P1_7 pin INT3: Port P3_3 direction register Figure 12.14 Configuration of INTi Input Filter INTi input Sampling timing IR bit in INTiIC register Set to 0 in program This is an operation example when bits INTiF1 to INTiF0 in the INTiF register are set to 01b, 10b, or 11b (passing digital filter). i = 0, 1, 3 Figure 12.15 Operating Example of INTi Input Filter Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 126 of 453 R8C/26 Group, R8C/27 Group 12.3 12. Interrupts Key Input Interrupt A key input interrupt request is generated by one of the input edges of the K10 to K13 pins. The key input interrupt can be used as a key-on wake-up function to exit wait or stop mode. The KIiEN (i = 0 to 3) bit in the KIEN register can select whether the pins are used as KIi input. The KIiPL bit in the KIEN register can select the input polarity. When inputting "L" to the KIi pin which sets the KIiPL bit to 0 (falling edge), the input of the other pins K10 to K13 is not detected as interrupts. Also, when inputting "H" to the KIi pin, which sets the KIiPL bit to 1 (rising edge), the input of the other pins K10 to K13 is not detected as interrupts. Figure 12.16 shows a Block Diagram of Key Input Interrupt. PU02 bit in PUR0 register KUPIC register Pull-up transistor PD1_3 bit in PD1 register KI3EN bit PD1_3 bit KI3PL = 0 KI3 KI3PL = 1 Pull-up transistor KI2EN bit PD1_2 bit KI2PL = 0 Interrupt control circuit KI2 KI2PL = 1 Pull-up transistor Key input interrupt request KI1EN bit PD1_1 bit KI1PL = 0 KI1 KI1PL = 1 Pull-up transistor KI0EN bit PD1_0 bit KI0PL = 0 KI0 KI0PL = 1 Figure 12.16 Block Diagram of Key Input Interrupt Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 127 of 453 KI0EN, KI1EN, KI2EN, KI3EN, KI0PL, KI1PL, KI2PL, KI3PL: Bits in KIEN register PD1_0, PD1_1, PD1_2, PD1_3: Bits in PD1 register R8C/26 Group, R8C/27 Group 12. Interrupts Key Input Enable Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol KIEN Bit Symbol KI0EN KI0PL KI1EN KI1PL KI2EN KI2PL KI3EN KI3PL Address 00FBh Bit Name KI0 input enable bit After Reset 00h Function RW KI0 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI1 input enable bit 0 : Disable 1 : Enable RW KI1 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI2 input enable bit 0 : Disable 1 : Enable RW KI2 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI3 input enable bit 0 : Disable 1 : Enable RW KI3 input polarity select bit 0 : Falling edge 1 : Rising edge RW NOTE: 1. The IR bit in the KUPIC register may be set to 1 (requests interrupt) w hen the KIEN register is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.17 KIEN Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : Disable 1 : Enable Page 128 of 453 R8C/26 Group, R8C/27 Group 12.4 12. Interrupts Address Match Interrupt An address match interrupt request is generated immediately before execution of the instruction at the address indicated by the RMADi register (i = 0 or 1). This interrupt is used as a break function by the debugger. When using the on-chip debugger, do not set an address match interrupt (registers of AIER, RMAD0, and RMAD1 and fixed vector tables) in a user system. Set the starting address of any instruction in the RMADi register. Bits AIER0 and AIER1 in the AIER0 register can be used to select enable or disable of the interrupt. The I flag and IPL do not affect the address match interrupt. The value of the PC (refer to 12.1.6.7 Saving a Register for the value of the PC) which is saved to the stack when an address match interrupt is acknowledged varies depending on the instruction at the address indicated by the RMADi register. (The appropriate return address is not saved on the stack.) When returning from the address match interrupt, return by one of the following means: * Change the content of the stack and use the REIT instruction. * Use an instruction such as POP to restore the stack as it was before the interrupt request was acknowledged. Then use a jump instruction. Table 12.7 lists the Values of PC Saved to Stack when Address Match Interrupt is Acknowledged. Figure 12.18 shows Registers AIER and RMAD0 to RMAD1. Table 12.7 Values of PC Saved to Stack when Address Match Interrupt is Acknowledged Address Indicated by RMADi Register (i = 0 or 1) * Instruction with 2-byte operation code(2) * Instruction with 1-byte operation code(2) ADD.B:S #IMM8,dest SUB.B:S #IMM8,dest AND.B:S #IMM8,dest OR.B:S #IMM8,dest MOV.B:S #IMM8,dest STZ #IMM8,dest STNZ #IMM8,dest STZX #IMM81,#IMM82,dest CMP.B:S #IMM8,dest PUSHM src POPM dest JMPS #IMM8 JSRS #IMM8 MOV.B:S #IMM,dest (however, dest = A0 or A1) Instructions other than the above PC Value Saved(1) Address indicated by RMADi register + 2 Address indicated by RMADi register + 1 NOTES: 1. Refer to the 12.1.6.7 Saving a Register for the PC value saved. 2. Operation code: Refer to the R8C/Tiny Series Software Manual (REJ09B0001). Chapter 4. Instruction Code/Number of Cycles contains diagrams showing operation code below each syntax. Operation code is shown in the bold frame in the diagrams. Table 12.8 Correspondence Between Address Match Interrupt Sources and Associated Registers Address Match Interrupt Source Address Match Interrupt Enable Bit Address Match Interrupt Register Address match interrupt 0 AIER0 RMAD0 Address match interrupt 1 AIER1 RMAD1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 129 of 453 R8C/26 Group, R8C/27 Group 12. Interrupts Address Match Interrupt Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER Bit Symbol AIER0 AIER1 -- (b7-b2) Address 0013h Bit Name Address match interrupt 0 enable bit 0 : Disable 1 : Enable After Reset 00h Function RW RW Address match interrupt 1 enable bit 0 : Disable 1 : Enable RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Address Match Interrupt Register i (i = 0 or 1) (b23) b7 (b19) b3 (b16) (b15) b0 b7 (b8) b0 b7 b0 Symbol RMAD0 RMAD1 Address 0012h-0010h 0016h-0014h Function Address setting register for address match interrupt -- Nothing is assigned. If necessary, set to 0. (b7-b4) When read, the content is 0. Figure 12.18 Registers AIER and RMAD0 to RMAD1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 130 of 453 After Reset 000000h 000000h Setting Range RW 00000h to FFFFFh RW -- R8C/26 Group, R8C/27 Group 12.5 12. Interrupts Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupts, and I2C bus Interface Interrupt (Interrupts with Multiple Interrupt Request Sources) The timer RC interrupt, clock synchronous serial I/O with chip select interrupt, and I2C bus interface interrupt each have multiple interrupt request sources. An interrupt request is generated by the logical OR of several interrupt request factors and is reflected in the IR bit in the corresponding interrupt control register. Therefore, each of these peripheral functions has its own interrupt request source status register (status register) and interrupt request source enable register (enable register) to control the generation of interrupt requests (change the IR bit in the interrupt control register). Table 12.9 lists the Registers Associated with Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt, and I2C bus Interface Interrupt and Figure 12.19 shows a Block Diagram of Timer RC Interrupt. Table 12.9 Registers Associated with Timer RC Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt, and I2C bus Interface Interrupt Status Register of Enable Register of Interrupt Control Interrupt Request Source Interrupt Request Source Register Timer RC TRCSR TRCIER TRCIC Clock synchronous serial SSSR SSER SSUIC I/O with chip select ICSR ICIER IICIC I2C bus interface IMFA bit IMIEA bit IMFB bit IMIEB bit IMFC bit IMIEC bit IMFD bit IMIED bit OVF bit OVIE bit IMFA, IMFB, IMFC, IMFD, OVF: Bits in TRCSR register IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRCIER register Figure 12.19 Block Diagram of Timer RC Interrupt Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 131 of 453 Timer RC interrupt request (IR bit in TRCIC register) R8C/26 Group, R8C/27 Group 12. Interrupts As with other maskable interrupts, the timer RC interrupt, clock synchronous serial I/O with chip select interrupt, and I2C bus interface interrupt are controlled by the combination of the I flag, IR bit, bits ILVL0 to ILVL2, and IPL. However, since each interrupt source is generated by a combination of multiple interrupt request sources, the following differences from other maskable interrupts apply: * When bits in the enable register corresponding to bits set to 1 in the status register are set to 1 (enable interrupt), the IR bit in the interrupt control register is set to 1 (interrupt requested). * When either bits in the status register or bits in the enable register corresponding to bits in the status register, or both, are set to 0, the IR bit is set to 0 (interrupt not requested). Basically, even though the interrupt is not acknowledged after the IR bit is set to 1, the interrupt request will not be maintained. Also, the IR bit is not set to 0 even if 0 is written to the IR bit. * Individual bits in the status register are not automatically set to 0 even if the interrupt is acknowledged. Therefore, the IR bit is also not automatically set to 0 when the interrupt is acknowledged. Set each bit in the status register to 0 in the interrupt routine. Refer to the status register figure for how to set individual bits in the status register to 0. * When multiple bits in the enable register are set to 1 and other request sources are generated after the IR bit is set to 1, the IR bit remains 1. * When multiple bits in the enable register are set to 1, determine by the status register which request source causes an interrupt. Refer to chapters of the individual peripheral functions (14.3 Timer RC, 16.2 Clock Synchronous Serial I/O with Chip Select (SSU) and 16.3 I2C bus Interface) for the status register and enable register. Refer to 12.1.6 Interrupt Control for the interrupt control register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 132 of 453 R8C/26 Group, R8C/27 Group 12.6 12. Interrupts Notes on Interrupts 12.6.1 Reading Address 00000h Do not read address 00000h by a program. When a maskable interrupt request is acknowledged, the CPU reads interrupt information (interrupt number and interrupt request level) from 00000h in the interrupt sequence. At this time, the acknowledged interrupt IR bit is set to 0. If address 00000h is read by a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is set to 0. This may cause the interrupt to be canceled, or an unexpected interrupt to be generated. 12.6.2 SP Setting Set any value in the SP before an interrupt is acknowledged. The SP is set to 0000h after reset. Therefore, if an interrupt is acknowledged before setting a value in the SP, the program may run out of control. 12.6.3 External Interrupt and Key Input Interrupt Either "L" level or an "H" level of width shown in the Electrical Characteristics is necessary for the signal input to pins INT0, INT1, INT3 and pins KI0 to KI3, regardless of the CPU clock. For details, refer to Table 20.21 (VCC = 5V), Table 20.27 (VCC = 3V), Table 20.33 (VCC = 2.2V), Table 20.52 (VCC = 5V), Table 20.58 (VCC = 3V) External Interrupt INTi (i = 0, 1, 3) Input. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 133 of 453 R8C/26 Group, R8C/27 Group 12.6.4 12. Interrupts Changing Interrupt Sources The IR bit in the interrupt control register may be set to 1 (interrupt requested) when the interrupt source changes. When using an interrupt, set the IR bit to 0 (no interrupt requested) after changing the interrupt source. In addition, changes of interrupt sources include all factors that change the interrupt sources assigned to individual software interrupt numbers, polarities, and timing. Therefore, if a mode change of a peripheral function involves interrupt sources, edge polarities, and timing, set the IR bit to 0 (no interrupt requested) after the change. Refer to the individual peripheral function for its related interrupts. Figure 12.20 shows an Example of Procedure for Changing Interrupt Sources. Interrupt source change Disable interrupts(2, 3) Change interrupt source (including mode of peripheral function) Set the IR bit to 0 (interrupt not requested) using the MOV instruction(3) Enable interrupts (2, 3) Change completed IR bit: The interrupt control register bit of an interrupt whose source is changed. NOTES: 1. Execute the above settings individually. Do not execute two or more settings at once (by one instruction). 2. To prevent interrupt requests from being generated, disable the peripheral function before changing the interrupt source. In this case, use the I flag if all maskable interrupts can be disabled. If all maskable interrupts cannot be disabled, use bits ILVL0 to ILVL2 of the interrupt whose source is changed. 3. Refer to 12.6.5 Changing Interrupt Control Register Contents for the instructions to be used and usage notes. Figure 12.20 Example of Procedure for Changing Interrupt Sources Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 134 of 453 R8C/26 Group, R8C/27 Group 12.6.5 12. Interrupts Changing Interrupt Control Register Contents (a) The contents of an interrupt control register can only be changed while no interrupt requests corresponding to that register are generated. If interrupt requests may be generated, disable interrupts before changing the interrupt control register contents. (b) When changing the contents of an interrupt control register after disabling interrupts, be careful to choose appropriate instructions. Changing any bit other than IR bit If an interrupt request corresponding to a register is generated while executing the instruction, the IR bit may not be set to 1 (interrupt requested), and the interrupt request may be ignored. If this causes a problem, use the following instructions to change the register: AND, OR, BCLR, BSET Changing IR bit If the IR bit is set to 0 (interrupt not requested), it may not be set to 0 depending on the instruction used. Therefore, use the MOV instruction to set the IR bit to 0. (c) When disabling interrupts using the I flag, set the I flag as shown in the sample programs below. Refer to (b) regarding changing the contents of interrupt control registers by the sample programs. Sample programs 1 to 3 are for preventing the I flag from being set to 1 (interrupts enabled) before the interrupt control register is changed for reasons of the internal bus or the instruction queue buffer. Example 1: Use NOP instructions to prevent I flag from being set to 1 before interrupt control register is changed INT_SWITCH1: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h NOP ; NOP FSET I ; Enable interrupts Example 2: Use dummy read to delay FSET instruction INT_SWITCH2: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h MOV.W MEM,R0 ; Dummy read FSET I ; Enable interrupts Example 3: Use POPC instruction to change I flag INT_SWITCH3: PUSHC FLG FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h POPC FLG ; Enable interrupts Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 135 of 453 R8C/26 Group, R8C/27 Group 13. Watchdog Timer 13. Watchdog Timer The watchdog timer is a function that detects when a program is out of control. Use of the watchdog timer is recommended to improve the reliability of the system. The watchdog timer contains a 15-bit counter and allows selection of count source protection mode enable or disable. Table 13.1 lists information on the Count Source Protection Mode. Refer to 5.7 Watchdog Timer Reset for details on the watchdog timer. Figure 13.1 shows the Block Diagram of Watchdog Timer. Figure 13.2 shows Registers OFS and WDC. Figure 13.3 shows Registers WDTR, WDTS, and CSPR. Table 13.1 Count Source Protection Mode Count Source Protection Mode Disabled CPU clock Item Count source Count Source Protection Mode Enabled Low-speed on-chip oscillator clock Count operation Count start condition Decrement Either of the following can be selected * After reset, count starts automatically * Count starts by writing to WDTS register Count stop condition Stop mode, wait mode None Reset condition of watchdog * Reset timer * Write 00h to the WDTR register before writing FFh * Underflow Operation at the time of underflow Watchdog timer interrupt or Watchdog timer reset watchdog timer reset Prescaler 1/16 WDC7 = 0 CSPRO = 0 1/128 CPU clock PM12 = 0 Watchdog timer interrupt request Watchdog timer WDC7 = 1 fOCO-S CSPRO = 1 Write to WDTR register Set to 7FFFh(1) PM12 = 1 Watchdog timer reset Internal reset signal CSPRO: Bit in CSPR register WDC7: Bit in WDC register PM12: Bit in PM1 register NOTE: 1. When the CSPRO bit is set to 1 (count source protection mode enabled), 0FFFh is set. Figure 13.1 Block Diagram of Watchdog Timer Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 136 of 453 R8C/26 Group, R8C/27 Group 13. Watchdog Timer Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON LVD1ON Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2, 4) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset RW Voltage detection 1 circuit start bit(5, 6) 0 : Voltage monitor 1 reset enabled after hardw are reset 1 : Voltage monitor 1 reset disabled after hardw are reset RW Count source protect CSPROINI mode after reset select bit RW RW RW RW 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. The LVD0ON bit setting is valid only by a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. 4. For N, D version only. For J, K version, set the LVD0ON bit to 1 (voltage monitor 0 reset disabled after hardw are reset). 5. The LVD1ON bit setting is valid only by a hardw are reset. When the pow er-on reset function is used, set the LVD1ON bit to 0 (voltage monitor 1 reset enabled after hardw are reset). 6. For J, K version only. For N, D version, set the LVD1ON bit to 1 (voltage monitor 1 reset disabled after hardw are reset). Watchdog Timer Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol Address 000Fh WDC Bit Symbol Bit Name -- High-order bits of w atchdog timer (b4-b0) -- (b5) Reserved bit Set to 0. When read, the content is undefined. -- (b6) Reserved bit Set to 0. Prescaler select bit 0 : Divide-by-16 1 : Divide-by-128 WDC7 Figure 13.2 Registers OFS and WDC Rev.2.10 Sep 26, 2008 REJ09B0278-0210 After Reset 00X11111b Function Page 137 of 453 RW RO RW RW RW R8C/26 Group, R8C/27 Group 13. Watchdog Timer Watchdog Timer Reset Register b7 b0 Symbol WDTR Address 000Dh After Reset Undefined Function When 00h is w ritten before w riting FFh, the w atchdog timer is reset.(1) The default value of the w atchdog timer is 7FFFh w hen count source protection mode is disabled and 0FFFh w hen count source protection mode is enabled.(2) RW WO NOTES: 1. Do not generate an interrupt betw een w hen 00h and FFh are w ritten. 2. When the CSPRO bit in the CSPR register is set to 1 (count source protection mode enabled), 0FFFh is set in the w atchdog timer. Watchdog Timer Start Register b7 b0 Symbol WDTS Address 000Eh After Reset Undefined Function The w atchdog timer starts counting after a w rite instruction to this register. RW WO Count Source Protection Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 Symbol Address 001Ch CSPR Bit Symbol Bit Name Reserved Bits -- (b6-b0) CSPRO After Reset(1) 00h Function Set to 0. Count Source Protection Mode 0 : Count source protection mode disabled Select Bit(2) 1 : Count source protection mode enabled NOTES: 1. When 0 is w ritten to the CSPROINI bit in the OFS register, the value after reset is 10000000b. 2. Write 0 before w riting 1 to set the CSPRO bit to 1. 0 cannot be set by a program. Figure 13.3 Registers WDTR, WDTS, and CSPR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 138 of 453 RW RW RW R8C/26 Group, R8C/27 Group 13.1 13. Watchdog Timer Count Source Protection Mode Disabled The count source of the watchdog timer is the CPU clock when count source protection mode is disabled. Table 13.2 lists the Specifications of Watchdog Timer (with Count Source Protection Mode Disabled). Table 13.2 Specifications of Watchdog Timer (with Count Source Protection Mode Disabled) Item Specification Count source Count operation Period CPU clock Decrement Count start condition The WDTON bit(2) in the OFS register (0FFFFh) selects the operation of the watchdog timer after a reset * When the WDTON bit is set to 1 (watchdog timer is in stop state after reset) The watchdog timer and prescaler stop after a reset and the count starts when the WDTS register is written to * When the WDTON bit is set to 0 (watchdog timer starts automatically after exiting) The watchdog timer and prescaler start counting automatically after a reset * Reset * Write 00h to the WDTR register before writing FFh * Underflow Stop and wait modes (inherit the count from the held value after exiting modes) * When the PM12 bit in the PM1 register is set to 0 Watchdog timer interrupt * When the PM12 bit in the PM1 register is set to 1 Watchdog timer reset (Refer to 5.7 Watchdog Timer Reset) Division ratio of prescaler (n) x count value of watchdog timer (32768)(1) CPU clock n: 16 or 128 (selected by WDC7 bit in WDC register) Example: When the CPU clock frequency is 16 MHz and prescaler divides by 16, the period is approximately 32.8 ms Reset condition of watchdog timer Count stop condition Operation at time of underflow NOTES: 1. The watchdog timer is reset when 00h is written to the WDTR register before FFh. The prescaler is reset after the MCU is reset. Some errors in the period of the watchdog timer may be caused by the prescaler. 2. The WDTON bit cannot be changed by a program. To set the WDTON bit, write 0 to bit 0 of address 0FFFFh with a flash programmer. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 139 of 453 R8C/26 Group, R8C/27 Group 13.2 13. Watchdog Timer Count Source Protection Mode Enabled The count source of the watchdog timer is the low-speed on-chip oscillator clock when count source protection mode is enabled. If the CPU clock stops when a program is out of control, the clock can still be supplied to the watchdog timer. Table 13.3 lists the Specifications of Watchdog Timer (with Count Source Protection Mode Enabled). Table 13.3 Specifications of Watchdog Timer (with Count Source Protection Mode Enabled) Item Specification Low-speed on-chip oscillator clock Decrement Count value of watchdog timer (4096) Low-speed on-chip oscillator clock Example: Period is approximately 32.8 ms when the low-speed on-chip oscillator clock frequency is 125 kHz Count source Count operation Period Count start condition Reset condition of watchdog timer Count stop condition Operation at time of underflow Registers, bits The WDTON bit(1) in the OFS register (0FFFFh) selects the operation of the watchdog timer after a reset. * When the WDTON bit is set to 1 (watchdog timer is in stop state after reset) The watchdog timer and prescaler stop after a reset and the count starts when the WDTS register is written to * When the WDTON bit is set to 0 (watchdog timer starts automatically after reset) The watchdog timer and prescaler start counting automatically after a reset * Reset * Write 00h to the WDTR register before writing FFh * Underflow None (The count does not stop in wait mode after the count starts. The MCU does not enter stop mode.) Watchdog timer reset (Refer to 5.7 Watchdog Timer Reset) * When setting the CSPPRO bit in the CSPR register to 1 (count source protection mode is enabled)(2), the following are set automatically - Set 0FFFh to the watchdog timer - Set the CM14 bit in the CM1 register to 0 (low-speed on-chip oscillator on) - Set the PM12 bit in the PM1 register to 1 (The watchdog timer is reset when watchdog timer underflows) * The following conditions apply in count source protection mode - Writing to the CM10 bit in the CM1 register is disabled (It remains unchanged even if it is set to 1. The MCU does not enter stop mode.) - Writing to the CM14 bit in the CM1 register is disabled (It remains unchanged even if it is set to 1. The low-speed on-chip oscillator does not stop.) NOTES: 1. The WDTON bit cannot be changed by a program. To set the WDTON bit, write 0 to bit 0 of address 0FFFFh with a flash programmer. 2. Even if 0 is written to the CSPROINI bit in the OFS register, the CSPRO bit is set to 1. The CSPROINI bit cannot be changed by a program. To set the CSPROINI bit, write 0 to bit 7 of address 0FFFFh with a flash programmer. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 140 of 453 R8C/26 Group, R8C/27 Group 14. Timers 14. Timers The microcomputer contains two 8-bit timers with 8-bit prescaler, a 16-bit timer, and a timer with a 4-bit counter, and an 8-bit counter. The two 8-bit timers with the 8-bit prescaler contain Timer RA and Timer RB. These timers contain a reload register to memorize the default value of the counter. The 16-bit timer is Timer RC which contains the input capture and output compare. The 4 and 8-bit counters are Timer RE which contains the output compare. All these timers operate independently. Table 14.1 lists Functional Comparison of Timers. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 141 of 453 R8C/26 Group, R8C/27 Group Table 14.1 14. Timers Functional Comparison of Timers Item Configuration Count Count source(1) Timer RA 8-bit timer with 8bit prescaler (with reload register) Decrement * f1 * f2 * f8 * fOCO * fC32 Timer RB 8-bit timer with 8bit prescaler (with reload register) Decrement * f1 * f2 * f8 * Timer RA underflow Function Timer Mode provided provided provided provided Pulse Output Mode Event Counter Mode Pulse Width Measurement Mode Pulse Period Measurement Mode Programmable Waveform Generation Mode Programmable One-Shot generation Mode Programmable Wait One-Shot Generation Mode Input Capture Mode Output Compare Mode PWM Mode PWM2 Mode Real-Time Clock Mode Input Pin Output Pin Related Interrupt Timer Stop not provided not provided Timer RC 16-bit free-run timer (with input capture and output compare) Increment * f1 * f2 * f4 * f8 * f32 * fOCO40M * TRCCLK provided (input capture function, output compare function) not provided not provided not provided not provided provided not provided not provided not provided provided not provided not provided not provided not provided provided not provided not provided not provided provided not provided not provided not provided provided not provided not provided not provided not provided not provided not provided provided provided not provided provided not provided not provided not provided not provided not provided not provided provided provided not provided not provided not provided provided(2) TRAIO INT0 INT0, TRCCLK, TRCTRG TRCIOA, TRCIOB, TRCIOC, TRCIOD TRAO TRBO TRCIOA, TRCIOB, TRAIO TRCIOC, TRCIOD Timer RA interrupt Timer RB interrupt Compare Match / Input INT1 interrupt INT0 interrupt Capture A to D interrupt Overflow interrupt INT0 interrupt provided provided provided NOTES: 1. For J, K version, fC4 and fC32 cannot be selected. 2. For N, D version only. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 142 of 453 Timer RE 4-bit counter 8-bit counter Increment * f4 * f8 * f32 * fC4 not provided - TREO Timer RE interrupt provided R8C/26 Group, R8C/27 Group 14.1 14. Timers Timer RA Timer RA is an 8-bit timer with an 8-bit prescaler. The prescaler and timer each consist of a reload register and counter. The reload register and counter are allocated at the same address, and can be accessed when accessing registers TRAPRE and TRA (refer to Tables 14.2 to 14.6 the Specifications of Each Mode). The count source for timer RA is the operating clock that regulates the timing of timer operations such as counting and reloading. Figure 14.1 shows a Block Diagram of Timer RA. Figures 14.2 and 14.3 show the registers associated with timer RA. Timer RA contains the following five operating modes: * Timer mode: The timer counts the internal count source. * Pulse output mode: The timer counts the internal count source and outputs pulses which invert the polarity by underflow of the timer. * Event counter mode: The timer counts external pulses. * Pulse width measurement mode: The timer measures the pulse width of an external pulse. * Pulse period measurement mode: The timer measures the pulse period of an external pulse. Data bus TCK2 to TCK0 bit f1 f8 fOCO f2 fC32(1) = 000b = 001b = 010b = 011b = 100b TMOD2 to TMOD0 = other than 010b TIPF1 to TIPF0 bits TMOD2 to TMOD0 = 010b Reload register TCKCUT TCSTF bit bit Reload register Counter TRAPRE register (prescaler) Counter TRA register (timer) Underflow signal Timer RA interrupt = 01b f1 = 10b f8 = 11b f32 TIPF1 to TIPF0 bits TIOSEL = 0 = other than Digital 000b INT1/TRAIO (P1_7) pin filter INT1/TRAIO (P1_5) pin TIOSEL = 1 TMOD2 to TMOD0 = 011b or 100b Polarity switching Count control circle = 00b TMOD2 to TMOD0 = 001b TEDGSEL = 1 TOPCR bit Q TOENA bit Q TEDGSEL = 0 Measurement completion signal Toggle flip-flop CK CLR Write to TRAMR register Write 1 to TSTOP bit TRAO pin TCSTF, TSTOP: TRACR register TEDGSEL, TOPCR, TOENA, TIOSEL, TIPF1, TIPF0: TRAIOC register TMOD2 to TMOD0, TCK2 to TCK0, TCKCUT: TRAMR register NOTE: 1. For J, K version, fC32 cannot be selected. Figure 14.1 Block Diagram of Timer RA Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 143 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RA Control Register(4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRACR Bit Symbol Address 0100h Bit Name Timer RA count start bit(1) After Reset 00h Function RW 0 : Count stops 1 : Count starts RW TCSTF Timer RA count status flag(1) 0 : Count stops 1 : During count RO TSTOP Timer RA count forcible stop When this bit is set to 1, the count is forcibly bit(2) stopped. When read, its content is 0. RW TSTART -- (b3) TEDGF Nothing is assigned. If necessary, set to 0. When read, the content is 0. Active edge judgment flag(3, 5) 0 : Active edge not received 1 : Active edge received (end of measurement period) -- RW TUNDF Timer RA underflow flag(3, 5) 0 : No underflow 1 : Underflow RW -- (b7-b6) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. Refer to 14.1.6 Notes on Tim er RA for precautions regarding bits TSTART and TCSTF. 2. When the TSTOP bit is set to 1, bits TSTART and TCSTF and registers TRAPRE and TRA are set to the values after a reset. 3. Bits TEDGF and TUNDF can be set to 0 by w riting 0 to these bits by a program. How ever, their value remains unchanged w hen 1 is w ritten. 4. In pulse w idth measurement mode and pulse period measurement mode, use the MOV instruction to set the TRACR register. If it is necessary to avoid changing the values of bits TEDGF and TUNDF, w rite 1 to them. 5. Set to 0 in timer mode, pulse output mode, and event counter mode. Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR TOENA Address 0101h Bit Name TRAIO polarity sw itch bit After Reset 00h Function Function varies depending on operating mode. TRAIO output control bit TRAO output enable bit RW RW RW RW _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 14.2 INT1/TRAIO select bit TRAIO input filter select bits Nothing is assigned. If necessary, set to 0. When read, the content is 0. Registers TRACR and TRAIOC Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 144 of 453 RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Timer RA Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRAMR Bit Symbol TMOD0 Address 0102h Bit Name Timer RA operating mode select bits (1) TMOD1 TMOD2 After Reset 00h Function 0 0 0 : Timer mode 0 0 1 : Pulse output mode 0 1 0 : Event counter mode 0 1 1 : Pulse w idth measurement mode 1 0 0 : Pulse period measurement mode 101: 1 1 0 : Do not set. 111: -- (b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. TCK0 Timer RA count source select bits TCK1 TCK2 TCKCUT Timer RA count source cutoff bit RW b2 b1 b0 RW RW RW -- b6 b5 b4 0 0 0 : f1 0 0 1 : f8 0 1 0 : fOCO 0 1 1 : f2 1 0 0 : fC32(2) 101: 1 1 0 : Do not set. 111: RW RW RW 0 : Provides count source 1 : Cuts off count source RW NOTES: 1. When both the TSTART and TCSTF bits in the TRACR register are set to 0 (count stops), rew rite this register. 2. For J, K version, fC32 cannot be selected. Timer RA Prescaler Register b7 b0 Symbol TRAPRE Mode Timer mode Pulse output mode Event counter mode Pulse w idth measurement mode Address 0103h Function Counts an internal count source Counts an external count source Measure pulse w idth of input pulses from external (counts internal count source) Pulse period measurement mode Measure pulse period of input pulses from external (counts internal count source) After Reset FFh(1) Setting Range 00h to FFh 00h to FFh 00h to FFh RW RW RW RW 00h to FFh RW 00h to FFh RW After Reset FFh(1) Setting Range RW 00h to FFh RW NOTE: 1. When the TSTOP bit in the TRACR register is set to 1, the TRAPRE register is set to FFh. Timer RA Register b7 b0 Symbol TRA Mode All modes Address 0104h Function Counts on underflow of timer RA prescaler register NOTE: 1. When the TSTOP bit in the TRACR register is set to 1, the TRA register is set to FFh. Figure 14.3 Registers TRAMR, TRAPRE, and TRA Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 145 of 453 R8C/26 Group, R8C/27 Group 14.1.1 14. Timers Timer Mode In this mode, the timer counts an internally generated count source (refer to Table 14.2 Specifications of Timer Mode). Figure 14.4 shows the TRAIOC Register in Timer Mode. Table 14.2 Specifications of Timer Mode Item Count sources Specification fC32(1) Count operations Divide ratio Count start condition Count stop conditions Interrupt request generation timing f1, f2, f8, fOCO, * Decrement * When the timer underflows, the contents of the reload register are reloaded and the count is continued. 1/(n+1)(m+1) n: Value set in TRAPRE register, m: Value set in TRA register 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. When timer RA underflows [timer RA interrupt]. INT1/TRAIO pin function Programmable I/O port, or INT1 interrupt input Programmable I/O port TRAO pin function Read from timer Write to timer The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter (refer to 14.1.1.1 Timer Write Control during Count Operation). NOTE: 1. For J, K version, fC32 cannot be selected. Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR TOENA Address 0101h Bit Name TRAIO polarity sw itch bit TRAIO output control bit TIPF0 TIPF1 -- (b7-b6) Figure 14.4 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits Set to 0 in timer mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Page 146 of 453 RW _____ INT1/TRAIO select bit TRAIOC Register in Timer Mode RW RW TRAO output enable bit _____ TIOSEL After Reset 00h Function Set to 0 in timer mode. RW RW -- R8C/26 Group, R8C/27 Group 14.1.1.1 14. Timers Timer Write Control during Count Operation Timer RA has a prescaler and a timer (which counts the prescaler underflows). The prescaler and timer each consist of a reload register and a counter. When writing to the prescaler or timer, values are written to both the reload register and counter. However, values are transferred from the reload register to the counter of the prescaler in synchronization with the count source. In addition, values are transferred from the reload register to the counter of the timer in synchronization with prescaler underflows. Therefore, if the prescaler or timer is written to when count operation is in progress, the counter value is not updated immediately after the WRITE instruction is executed. Figure 14.5 shows an Operating Example of Timer RA when Counter Value is Rewritten during Count Operation. Set 01h to the TRAPRE register and 25h to the TRA register by a program. Count source After writing, the reload register is written to at the first count source. Reloads register of timer RA prescaler Previous value New value (01h) Reload at second count source Counter of timer RA prescaler 06h 05h 04h 01h 00h Reload at underflow 01h 00h 01h 00h 01h 00h After writing, the reload register is written to at the first underflow. Reloads register of timer RA Previous value New value (25h) Reload at the second underflow Counter of timer RA IR bit in TRAIC register 03h 02h 25h 24h 0 The IR bit remains unchanged until underflow is generated by a new value. The above applies under the following conditions. Both bits TSTART and TCSTF in the TRACR register are set to 1 (During count). Figure 14.5 Operating Example of Timer RA when Counter Value is Rewritten during Count Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 147 of 453 R8C/26 Group, R8C/27 Group 14.1.2 14. Timers Pulse Output Mode In pulse output mode, the internally generated count source is counted, and a pulse with inverted polarity is output from the TRAIO pin each time the timer underflows (refer to Table 14.3 Specifications of Pulse Output Mode). Figure 14.6 shows the TRAIOC Register in Pulse Output Mode. Table 14.3 Specifications of Pulse Output Mode Item Count sources Count operations Divide ratio Count start condition Count stop conditions Interrupt request generation timing Specification fC32(2) f1, f2, f8, fOCO, * Decrement * When the timer underflows, the contents in the reload register is reloaded and the count is continued. 1/(n+1)(m+1) n: Value set in TRAPRE register, m: Value set in TRA register 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. When timer RA underflows [timer RA interrupt]. INT1/TRAIO pin function Pulse output, programmable output port, or INT1 interrupt(1) TRAO pin function Read from timer Write to timer Select functions Programmable I/O port or inverted output of TRAIO(1) The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter (refer to 14.1.1.1 Timer Write Control during Count Operation). * TRAIO signal polarity switch function The TEDGSEL bit in the TRAIOC register selects the level at the start of pulse output.(1) * TRAO output function Pulses inverted from the TRAIO output polarity can be output from the TRAO pin (selectable by the TOENA bit in the TRAIOC register). * Pulse output stop function Output from the TRAIO pin is stopped by the TOPCR bit in the TRAIOC register. * INT1/TRAIO pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. NOTES: 1. The level of the output pulse becomes the level when the pulse output starts when the TRAMR register is written to. 2. For J, K version, fC32 cannot be selected. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 148 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR TOENA Address 0101h Bit Name TRAIO polarity sw itch bit After Reset 00h Function 0 : TRAIO output starts at "H" 1 : TRAIO output starts at "L" RW TRAIO output control bit 0 : TRAIO output 1 : Port P1_7 or P1_5 RW TRAO output enable bit 0 : Port P3_7 1 : TRAO output (inverted TRAIO output from P3_7) RW _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 14.6 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 _____ INT1/TRAIO select bit 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits Set to 0 in pulse output mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. TRAIOC Register in Pulse Output Mode Page 149 of 453 RW RW RW RW -- R8C/26 Group, R8C/27 Group 14.1.3 14. Timers Event Counter Mode In event counter mode, external signal inputs to the INT1/TRAIO pin are counted (refer to Table 14.4 Specifications of Event Counter Mode). Figure 14.7 shows the TRAIOC Register in Event Counter Mode. Table 14.4 Specifications of Event Counter Mode Item Count source Count operations Divide ratio Count start condition Count stop conditions Interrupt request generation timing Specification External signal which is input to TRAIO pin (active edge selectable by a program) * Decrement * When the timer underflows, the contents of the reload register are reloaded and the count is continued. 1/(n+1)(m+1) n: setting value of TRAPRE register, m: setting value of TRA register 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. * When timer RA underflows [timer RA interrupt]. INT1/TRAIO pin function Count source input (INT1 interrupt input) TRAO pin function Read from timer Write to timer Programmable I/O port or pulse output(1) The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter (refer to 14.1.1.1 Timer Write Control during Count Operation). Select functions * INT1 input polarity switch function The TEDGSEL bit in the TRAIOC register selects the active edge of the count source. * Count source input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Pulse output function Pulses of inverted polarity can be output from the TRAO pin each time the timer underflows (selectable by the TOENA bit in the TRAIOC register).(1) * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. NOTE: 1. The level of the output pulse becomes the level when the pulse output starts when the TRAMR register is written to. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 150 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRAIOC Bit Symbol Address 0101h Bit Name TRAIO polarity sw itch bit TEDGSEL TOPCR TOENA TRAIO output control bit Set to 0 in event counter mode. TRAO output enable bit 0 : Port P3_7 1 : TRAO output _____ TIOSEL TIPF0 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 14.7 TRAIOC Register in Event Counter Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 151 of 453 RW RW RW RW _____ INT1/TRAIO select bit TIPF1 -- (b7-b6) After Reset 00h Function 0 : Starts counting at rising edge of the TRAIO input or TRAIO starts output at "L" 1 : Starts counting at falling edge of the TRAIO input or TRAIO starts output at "H" RW RW -- R8C/26 Group, R8C/27 Group 14.1.4 14. Timers Pulse Width Measurement Mode In pulse width measurement mode, the pulse width of an external signal input to the INT1/TRAIO pin is measured (refer to Table 14.5 Specifications of Pulse Width Measurement Mode). Figure 14.8 shows the TRAIOC Register in Pulse Width Measurement Mode and Figure 14.9 shows an Operating Example of Pulse Width Measurement Mode. Table 14.5 Specifications of Pulse Width Measurement Mode Item Count sources Count operations Count start condition Count stop conditions Interrupt request generation timing Specification fC32(1) f1, f2, f8, fOCO, * Decrement * Continuously counts the selected signal only when measurement pulse is "H" level, or conversely only "L" level. * When the timer underflows, the contents of the reload register are reloaded and the count is continued. 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. * When timer RA underflows [timer RA interrupt]. * Rising or falling of the TRAIO input (end of measurement period) [timer RA interrupt] INT1/TRAIO pin function Measured pulse input (INT1 interrupt input) Programmable I/O port TRAO pin function Read from timer Write to timer Select functions The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter (refer to 14.1.1.1 Timer Write Control during Count Operation). * Measurement level select The TEDGSEL bit in the TRAIOC register selects the "H" or "L" level period. * Measured pulse input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. NOTE: 1. For J, K version, fC32 cannot be selected. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 152 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR TOENA Address 0101h Bit Name TRAIO polarity sw itch bit After Reset 00h Function 0 : TRAIO input starts at "L" 1 : TRAIO input starts at "H" TRAIO output control bit Set to 0 in pulse w idth measurement mode. TRAO output enable bit _____ TIOSEL TIPF0 -- (b7-b6) 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. TRAIOC Register in Pulse Width Measurement Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 153 of 453 RW RW NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 14.8 RW _____ INT1/TRAIO select bit TIPF1 RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers n = high level: the contents of TRA register, low level: the contents of TRAPRE register FFFFh Count start Underflow Content of counter (hex) n Count stop Count stop Count start Count start 0000h Period Set to 1 by program TSTART bit in TRACR register 1 Measured pulse (TRAIO pin input) 1 0 0 Set to 0 when interrupt request is acknowledged, or set by program IR bit in TRAIC register 1 0 Set to 0 by program TEDGF bit in TRACR register 1 0 Set to 0 by program TUNDF bit in TRACR register 1 0 The above applies under the following conditions. * "H" level width of measured pulse is measured. (TEDGSEL = 1) * TRAPRE = FFh Figure 14.9 Operating Example of Pulse Width Measurement Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 154 of 453 R8C/26 Group, R8C/27 Group 14.1.5 14. Timers Pulse Period Measurement Mode In pulse period measurement mode, the pulse period of an external signal input to the INT1/TRAIO pin is measured (refer to Table 14.6 Specifications of Pulse Period Measurement Mode). Figure 14.10 shows the TRAIOC Register in Pulse Period Measurement Mode and Figure 14.11 shows an Operating Example of Pulse Period Measurement Mode. Table 14.6 Specifications of Pulse Period Measurement Mode Item Count sources Count operations Count start condition Count stop conditions Interrupt request generation timing Specification fC32(2) f1, f2, f8, fOCO, * Decrement * After the active edge of the measured pulse is input, the contents of the readout buffer are retained at the first underflow of timer RA prescaler. Then timer RA reloads the contents in the reload register at the second underflow of timer RA prescaler and continues counting. 1 (count start) is written to the TSTART bit in the TRACR register. * 0 (count stop) is written to TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. * When timer RA underflows or reloads [timer RA interrupt]. * Rising or falling of the TRAIO input (end of measurement period) [timer RA interrupt] INT1/TRAIO pin function Measured pulse input(1) (INT1 interrupt input) Programmable I/O port TRAO pin function Read from timer Write to timer Select functions The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter (refer to 14.1.1.1 Timer Write Control during Count Operation). * Measurement period select The TEDGSEL bit in the TRAIOC register selects the measurement period of the input pulse. * Measured pulse input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. NOTES: 1. Input a pulse with a period longer than twice the timer RA prescaler period. Input a pulse with a longer "H" and "L" width than the timer RA prescaler period. If a pulse with a shorter period is input to the TRAIO pin, the input may be ignored. 2. For J, K version, fC32 cannot be selected. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 155 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol Address 0101h Bit Name TRAIO polarity sw itch bit TEDGSEL TOPCR TOENA TRAIO output control bit TIPF0 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. TRAIOC Register in Pulse Period Measurement Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 156 of 453 RW RW RW NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 14.10 RW _____ INT1/TRAIO select bit TIPF1 -- (b7-b6) Set to 0 in pulse period measurement mode. TRAO output enable bit _____ TIOSEL After Reset 00h Function 0 : Measures measurement pulse from one rising edge to next rising edge 1 : Measures measurement pulse from one falling edge to next falling edge RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Underflow signal of timer RA prescaler Set to 1 by program TSTART bit in TRACR register 1 0 Starts counting Measurement pulse (TRAIO pin input) 1 0 TRA reloads TRA reloads 0Fh 0Eh 0Dh 0Fh 0Eh 0Dh 0Ch 0Bh 0Ah 09h 0Fh 0Eh 0Dh Contents of TRA 01h 00h 0Fh 0Eh Underflow Retained Contents of read-out buffer(1) 0Fh Retained 0Dh 0Eh 0Bh 0Ah 09h 0Dh 01h 00h 0Fh 0Eh TRA read(3) (Note 2) TEDGF bit in TRACR register (Note 2) 1 0 Set to 0 by program (Note 4) (Note 6) TUNDF bit in TRACR register 1 0 Set to 0 by program IR bit in TRAIC register (Note 5) 1 0 Set to 0 when interrupt request is acknowledged, or set by program Conditions: The period from one rising edge to the next rising edge of the measured pulse is measured (TEDGSEL = 0) with the default value of the TRA register as 0Fh. NOTES: 1. The contents of the read-out buffer can be read by reading the TRA register in pulse period measurement mode. 2. After an active edge of the measured pulse is input, the TEDGF bit in the TRACR register is set to 1 (active edge found) when the timer RA prescaler underflows for the second time. 3. The TRA register should be read before the next active edge is input after the TEDGF bit is set to 1 (active edge found). The contents in the read-out buffer are retained until the TRA register is read. If the TRA register is not read before the next active edge is input, the measured result of the previous period is retained. 4. To set to 0 by a program, use a MOV instruction to write 0 to the TEDGF bit in the TRACR register. At the same time, write 1 to the TUNDF bit in the TRACR register. 5. To set to 0 by a program, use a MOV instruction to write 0 to the TUNDF bit. At the same time, write 1 to the TEDGF bit. 6. Bits TUNDF and TEDGF are both set to 1 if timer RA underflows and reloads on an active edge simultaneously. Figure 14.11 Operating Example of Pulse Period Measurement Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 157 of 453 R8C/26 Group, R8C/27 Group 14.1.6 14. Timers Notes on Timer RA * Timer RA stops counting after a reset. Set the values in the timer RA and timer RA prescalers before the count starts. * Even if the prescaler and timer RA are read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In pulse period measurement mode, bits TEDGF and TUNDF in the TRACR register can be set to 0 by writing 0 to these bits by a program. However, these bits remain unchanged if 1 is written. When using the READ-MODIFY-WRITE instruction for the TRACR register, the TEDGF or TUNDF bit may be set to 0 although these bits are set to 1 while the instruction is being executed. In this case, write 1 to the TEDGF or TUNDF bit which is not supposed to be set to 0 with the MOV instruction. * When changing to pulse period measurement mode from another mode, the contents of bits TEDGF and TUNDF are undefined. Write 0 to bits TEDGF and TUNDF before the count starts. * The TEDGF bit may be set to 1 by the first timer RA prescaler underflow generated after the count starts. * When using the pulse period measurement mode, leave two or more periods of the timer RA prescaler immediately after the count starts, then set the TEDGF bit to 0. * The TCSTF bit retains 0 (count stops) for 0 to 1 cycle of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. Timer RA starts counting at the first valid edge of the count source after The TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 0 to 1 cycle of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RA counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RA: TRACR, TRAIOC, TRAMR, TRAPRE, and TRA. * When the TRAPRE register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source clock for each write interval. * When the TRA register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 158 of 453 R8C/26 Group, R8C/27 Group 14.2 14. Timers Timer RB Timer RB is an 8-bit timer with an 8-bit prescaler. The prescaler and timer each consist of a reload register and counter (refer to Tables 14.7 to 14.10 the Specifications of Each Mode). Timer RB has timer RB primary and timer RB secondary as reload registers. The count source for timer RB is the operating clock that regulates the timing of timer operations such as counting and reloading. Figure 14.12 shows a Block Diagram of Timer RB. Figures 14.13 to 14.15 show the registers associated with timer RB. Timer RB has four operation modes listed as follows: * Timer mode: * Programmable waveform generation mode: * Programmable one-shot generation mode: * Programmable wait one-shot generation mode: Reload register TCK1 to TCK0 bits f1 f8 = 00b Timer RA underflow = 10b = 11b f2 The timer counts an internal count source (peripheral function clock or timer RA underflows). The timer outputs pulses of a given width successively. The timer outputs a one-shot pulse. The timer outputs a delayed one-shot pulse. Data bus TRBSC register Reload register TRBPR register Reload register TCKCUT bit = 01b Counter TRBPRE register (prescaler) Timer RB interrupt Counter (timer RB) (Timer) TMOD1 to TMOD0 bits = 10b or 11b TSTART bit TOSSTF bit INT0 interrupt Input polarity selected to be one edge or both edges Digital filter INT0 pin INT0PL bit TMOD1 to TMOD0 bits = 01b, 10b, 11b TRBO (P3_1) pin TRBOSEL = 0 P3_1 bit in P3 register TOCNT = 1 TSTART, TCSTF: Bits in TRBCR register TOSSTF: Bit in TRBOCR register TOPL, TOCNT, INOSTG, INOSEG: Bits in TRBIOC register TMOD1 to TMOD0, TCK1 to TCK0, TCKCUT: Bits in TRBMR register TRBOSEL: Bit in PINSR2 register Figure 14.12 Block Diagram of Timer RB Rev.2.10 Sep 26, 2008 REJ09B0278-0210 INOSEG bit Page 159 of 453 INOSTG bit TOPL = 1 TOCNT = 0 TRBO (P1_3) pin TRBOSEL = 1 INT0EN bit Polarity select TOPL = 0 Q Toggle flip-flop Q CLR CK TCSTF bit TMOD1 to TMOD0 bits = 01b, 10b, 11b R8C/26 Group, R8C/27 Group 14. Timers Timer RB Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBCR Bit Symbol TSTART Address 0108h Bit Name Timer RB count start bit(1) After Reset 00h Function 0 : Count stops 1 : Count starts RW RW TCSTF Timer RB count status flag(1) 0 : Count stops 1 : During count(3) RO TSTOP Timer RB count forcible stop When this bit is set to 1, the count is forcibly bit(1, 2) stopped. When read, its content is 0. RW -- (b7-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. Refer to 14.2.5 Notes on Tim er RB for precautions regarding bits TSTART, TCSTF and TSTOP. 2. When the TSTOP bit is set to 1, registers TRBPRE, TRBSC, TRBPR, and bits TSTART and TCSTF, and the TOSSTF bit in the TRBOCR register are set to values after a reset. 3. Indicates that count operation is in progress in timer mode or programmable w aveform mode. In programmable oneshot generation mode or programmable w ait one-shot generation mode, indicates that a one-shot pulse trigger has been acknow ledged. Timer RB One-Shot Control Register(2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBOCR Bit Symbol TOSST Address 0109h Bit Name Timer RB one-shot start bit After Reset 00h Function When this bit is set to 1, one-shot trigger generated. When read, its content is 0. Timer RB one-shot stop bit When this bit is set to 1, counting of one-shot pulses (including programmable w ait one-shot pulses) stops. When read, its content is 0. RW 0 : One-shot stopped 1 : One-shot operating (Including w ait period) RO TOSSP TOSSTF Timer RB one-shot status flag(1) -- (b7-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW RW NOTES: 1. When 1 is set to the TSTOP bit in the TRBCR register, the TOSSTF bit is set to 0. 2. This register is enabled w hen bits TMOD1 to TMOD0 in the TRBMR register is set to 10b (programmable one-shot generation mode) or 11b (programmable w ait one-shot generation mode). Figure 14.13 Registers TRBCR and TRBOCR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 160 of 453 -- R8C/26 Group, R8C/27 Group 14. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Address After Reset 010Ah 00h Bit Name Function Timer RB output level select Function varies depending on operating mode. bit Timer RB output sw itch bit RW RW RW One-shot trigger control bit RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Timer RB Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBMR Bit Symbol TMOD0 Address 010Bh Bit Name Timer RB operating mode select bits (1) TMOD1 -- (b2) TWRC TCK0 TCKCUT RW b1 b0 0 0 : Timer mode 0 1 : Programmable w aveform generation mode 1 0 : Programmable one-shot generation mode 1 1 : Programmable w ait one-shot generation mode Nothing is assigned. If necessary, set to 0. When read, the content is 0. Timer RB w rite control bit(2) 0 : Write to reload register and counter 1 : Write to reload register only Timer RB count source select bits (1) b5 b4 TCK1 -- (b6) After Reset 00h Function 0 0 : f1 0 1 : f8 1 0 : Timer RA underflow 1 1 : f2 RW RW -- RW RW RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Timer RB count source cutoff bit(1) RW 0 : Provides count source 1 : Cuts off count source NOTES: 1. Change bits TMOD1 and TMOD0; TCK1 and TCK0; and TCKCUT w hen both the TSTART and TCSTF bits in the TRBCR register set to 0 (count stops). 2. The TWRC bit can be set to either 0 or 1 in timer mode. In programmable w aveform generation mode, programmable one-shot generation mode, or programmable w ait one-shot generation mode, the TWRC bit must be set to 1 (w rite to reload register only). Figure 14.14 Registers TRBIOC and TRBMR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 161 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RB Prescaler Register(1) b7 b0 Symbol TRBPRE Mode Timer mode Address 010Ch Function Counts an internal count source or timer RA underflow s After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode 00h to FFh Programmable one-shot generation mode 00h to FFh Programmable w ait one-shot generation mode 00h to FFh RW RW RW RW RW NOTE: 1. When the TSTOP bit in the TRBCR register is set to 1, the TRBPRE register is set to FFh. Timer RB Secondary Register(3, 4) b7 b0 Symbol TRBSC Mode Timer mode Address 010Dh Function Disabled After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode Counts timer RB prescaler underflow s (1) 00h to FFh Programmable one-shot generation mode Disabled 00h to FFh Programmable w ait one-shot Counts timer RB prescaler underflow s generation mode (one-shot w idth is counted) 00h to FFh RW -- WO(2) -- WO(2) NOTES: 1. The values of registers TRBPR and TRBSC are reloaded to the counter alternately and counted. 2. The count value can be read out by reading the TRBPR register even w hen the secondary period is being counted. 3. When the TSTOP bit in the TRBCR register is set to 1, the TRBSC register is set to FFh. 4. To w rite to the TRBSC register, perform the follow ing steps. (1) Write the value to the TRBSC register. (2) Write the value to the TRBPR register. (If the value does not change, w rite the same value second time.) Timer RB Primary Register(2) b7 b0 Symbol TRBPR Mode Timer mode Address 010Eh Function Counts timer RB prescaler underflow s After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode Counts timer RB prescaler underflow s (1) 00h to FFh Programmable one-shot generation mode Counts timer RB prescaler underflow s (one-shot w idth is counted) 00h to FFh Programmable w ait one-shot Counts timer RB prescaler underflow s generation mode (w ait period w idth is counted) 00h to FFh NOTES: 1. The values of registers TRBPR and TRBSC are reloaded to the counter alternately and counted. 2. When the TSTOP bit in the TRBCR register is set to 1, the TRBPR register is set to FFh. Figure 14.15 Registers TRBPRE, TRBSC, and TRBPR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 162 of 453 RW RW RW RW RW R8C/26 Group, R8C/27 Group 14.2.1 14. Timers Timer Mode In timer mode, a count source which is internally generated or timer RA underflows are counted (refer to Table 14.7 Specifications of Timer Mode). Registers TRBOCR and TRBSC are not used in timer mode. Figure 14.16 shows the TRBIOC Register in Timer Mode. Table 14.7 Specifications of Timer Mode Item Count sources Count operations Specification Divide ratio Count start condition Count stop conditions Interrupt request generation timing TRBO pin function f1, f2, f8, timer RA underflow * Decrement * When the timer underflows, it reloads the reload register contents before the count continues (when timer RB underflows, the contents of timer RB primary reload register is reloaded). 1/(n+1)(m+1) n: setting value in TRBPRE register, m: setting value in TRBPR register 1 (count starts) is written to the TSTART bit in the TRBCR register. * 0 (count stops) is written to the TSTART bit in the TRBCR register. * 1 (count forcibly stop) is written to the TSTOP bit in the TRBCR register. When timer RB underflows [timer RB interrupt] Programmable I/O port INT0 pin function Read from timer Write to timer Programmable I/O port or INT0 interrupt input The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE and TRBPR are written to while count operation is in progress: If the TWRC bit in the TRBMR register is set to 0, the value is written to both the reload register and the counter. If the TWRC bit is set to 1, the value is written to the reload register only. (Refer to 14.2.1.1 Timer Write Control during Count Operation.) Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Figure 14.16 Address After Reset 010Ah 00h Bit Name Function Timer RB output level select Set to 0 in timer mode. bit Timer RB output sw itch bit One-shot trigger control bit RW RW RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- TRBIOC Register in Timer Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Page 163 of 453 R8C/26 Group, R8C/27 Group 14.2.1.1 14. Timers Timer Write Control during Count Operation Timer RB has a prescaler and a timer (which counts the prescaler underflows). The prescaler and timer each consist of a reload register and a counter. In timer mode, the TWRC bit in the TRBMR register can be used to select whether writing to the prescaler or timer during count operation is performed to both the reload register and counter or only to the reload register. However, values are transferred from the reload register to the counter of the prescaler in synchronization with the count source. In addition, values are transferred from the reload register to the counter of the timer in synchronization with prescaler underflows. Therefore, even if the TWRC bit is set for writing to both the reload register and counter, the counter value is not updated immediately after the WRITE instruction is executed. In addition, if the TWRC bit is set for writing to the reload register only, the synchronization of the writing will be shifted if the prescaler value changes. Figure 14.17 shows an Operating Example of Timer RB when Counter Value is Rewritten during Count Operation. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 164 of 453 R8C/26 Group, R8C/27 Group 14. Timers When the TWRC bit is set to 0 (write to reload register and counter) Set 01h to the TRBPRE register and 25h to the TRBPR register by a program. Count source After writing, the reload register is written with the first count source. Reloads register of timer RB prescaler Previous value Counter of timer RB prescaler 06h 05h New value (01h) 04h Reload with the second count source Reload on underflow 01h 01h 00h 00h 01h 00h 01h 00h After writing, the reload register is written on the first underflow. Reloads register of timer RB Previous value New value (25h) Reload on the second underflow Counter of timer RB IR bit in TRBIC register 03h 02h 25h 24h 0 The IR bit remains unchanged until underflow is generated by a new value. When the TWRC bit is set to 1 (write to reload register only) Set 01h to the TRBPRE register and 25h to the TRBPR register by a program. Count source After writing, the reload register is written with the first count source. Reloads register of timer RB prescaler Previous value New value (01h) Reload on underflow Counter of timer RB prescaler 06h 05h 04h 03h 02h 01h 00h 01h 00h 01h 00h 01h 00h 01h After writing, the reload register is written on the first underflow. Reloads register of timer RB Previous value New value (25h) Reload on underflow Counter of timer RB IR bit in TRBIC register 03h 02h 01h 00h 25h 0 Only the prescaler values are updated, extending the duration until timer RB underflow. The above applies under the following conditions. Both bits TSTART and TCSTF in the TRBCR register are set to 1 (During count). Figure 14.17 Operating Example of Timer RB when Counter Value is Rewritten during Count Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 165 of 453 R8C/26 Group, R8C/27 Group 14.2.2 14. Timers Programmable Waveform Generation Mode In programmable waveform generation mode, the signal output from the TRBO pin is inverted each time the counter underflows, while the values in registers TRBPR and TRBSC are counted alternately (refer to Table 14.8 Specifications of Programmable Waveform Generation Mode). Counting starts by counting the setting value in the TRBPR register. The TRBOCR register is unused in this mode. Figure 14.18 shows the TRBIOC Register in Programmable Waveform Generation Mode. Figure 14.19 shows an Operating Example of Timer RB in Programmable Waveform Generation Mode. Table 14.8 Specifications of Programmable Waveform Generation Mode Item Count sources Count operations Width and period of output waveform Count start condition Count stop conditions Interrupt request generation timing TRBO pin function INT0 pin function Read from timer Write to timer Select functions Specification f1, f2, f8, timer RA underflow * Decrement * When the timer underflows, it reloads the contents of the primary reload and secondary reload registers alternately before the count continues. Primary period: (n+1)(m+1)/fi Secondary period: (n+1)(p+1)/fi Period: (n+1){(m+1)+(p+1)}/fi fi: Count source frequency n: Value set in TRBPRE register, m: Value set in TRBPR register p: Value set in TRBSC register 1 (count start) is written to the TSTART bit in the TRBCR register. * 0 (count stop) is written to the TSTART bit in the TRBCR register. * 1 (count forcibly stop) is written to the TSTOP bit in the TRBCR register. In half a cycle of the count source, after timer RB underflows during the secondary period (at the same time as the TRBO output change) [timer RB interrupt] Programmable output port or pulse output Programmable I/O port or INT0 interrupt input The count value can be read out by reading registers TRBPR and TRBPRE.(1) * When registers TRBPRE, TRBSC, and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE, TRBSC, and TRBPR are written to during count operation, values are written to the reload registers only.(2) * Output level select function The TOPL bit in the TRBIOC register selects the output level during primary and secondary periods. * TRBO pin output switch function Timer RB pulse output or P3_1 (P1_3) latch output is selected by the TOCNT bit in the TRBIOC register.(3) * TRBO pin select function P3_1 or P1_3 is selected by the TRBOSEL bit in the PINSR2 register. NOTES: 1. Even when counting the secondary period, the TRBPR register may be read. 2. The set values are reflected in the waveform output beginning with the following primary period after writing to the TRBPR register. 3. The value written to the TOCNT bit is enabled by the following. * When counting starts. * When a timer RB interrupt request is generated. The contents after the TOCNT bit is changed are reflected from the output of the following primary period. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 166 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Figure 14.18 Address 010Ah Bit Name Timer RB output level select 0 : Outputs bit Outputs Outputs 1 : Outputs Outputs Outputs After Reset 00h Function "H" for primary period "L" for secondary period "L" w hen the timer is stopped "L" for primary period "H" for secondary period "H" w hen the timer is stopped RW Timer RB output sw itch bit 0 : Outputs timer RB w aveform 1 : Outputs value in P3_1 (P1_3) port register RW One-shot trigger control bit Set to 0 in programmable w aveform generation mode. RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- TRBIOC Register in Programmable Waveform Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Page 167 of 453 R8C/26 Group, R8C/27 Group 14. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Count source Timer RB prescaler underflow signal Timer RB secondary reloads 01h Counter of timer RB 00h 02h 01h Timer RB primary reloads 00h 01h 00h 02h Set to 0 when interrupt request is acknowledged, or set by program. IR bit in TRBIC register 1 0 Set to 0 by program TOPL bit in TRBIO register 1 0 Waveform output starts Waveform output inverted Waveform output starts 1 TRBO pin output 0 Initial output is the same level as during secondary period. Primary period Secondary period Primary period The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h, TRBSC = 02h TRBIOC register TOCNT = 0 (timer RB waveform is output from the TRBO pin) Figure 14.19 Operating Example of Timer RB in Programmable Waveform Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 168 of 453 R8C/26 Group, R8C/27 Group 14.2.3 14. Timers Programmable One-shot Generation Mode In programmable one-shot generation mode, a one-shot pulse is output from the TRBO pin by a program or an external trigger input (input to the INT0 pin) (refer to Table 14.9 Specifications of Programmable One-Shot Generation Mode). When a trigger is generated, the timer starts operating from the point only once for a given period equal to the set value in the TRBPR register. The TRBSC register is not used in this mode. Figure 14.20 shows the TRBIOC Register in Programmable One-Shot Generation Mode. Figure 14.21 shows an Operating Example of Programmable One-Shot Generation Mode. Table 14.9 Specifications of Programmable One-Shot Generation Mode Item Count sources Count operations One-shot pulse output time Count start conditions Count stop conditions Interrupt request generation timing TRBO pin function INT0 pin functions Read from timer Write to timer Select functions Specification f1, f2, f8, timer RA underflow * Decrement the setting value in the TRBPR register * When the timer underflows, it reloads the contents of the reload register before the count completes and the TOSSTF bit is set to 0 (one-shot stops). * When the count stops, the timer reloads the contents of the reload register before it stops. (n+1)(m+1)/fi fi: Count source frequency, n: Setting value in TRBPRE register, m: Setting value in TRBPR register(2) * The TSTART bit in the TRBCR register is set to 1 (count starts) and the next trigger is generated * Set the TOSST bit in the TRBOCR register to 1 (one-shot starts) * Input trigger to the INT0 pin * When reloading completes after timer RB underflows during primary period * When the TOSSP bit in the TRBOCR register is set to 1 (one-shot stops) * When the TSTART bit in the TRBCR register is set to 0 (stops counting) * When the TSTOP bit in the TRBCR register is set to 1 (forcibly stops counting) In half a cycle of the count source, after the timer underflows (at the same time as the TRBO output ends) [timer RB interrupt] Pulse output * When the INOSTG bit in the TRBIOC register is set to 0 (INT0 one-shot trigger disabled): programmable I/O port or INT0 interrupt input * When the INOSTG bit in the TRBIOC register is set to 1 (INT0 one-shot trigger enabled): external trigger (INT0 interrupt input) The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE and TRBPR are written during the count, values are written to the reload register only (the data is transferred to the counter at the following reload).(1) * Output level select function The TOPL bit in the TRBIOC register selects the output level of the one-shot pulse waveform. * One-shot trigger select function Refer to 14.2.3.1 One-Shot Trigger Selection. * TRBO pin select function P3_1 or P1_3 is selected by the TRBOSEL bit in the PINSR2 register. NOTES: 1. The set value is reflected at the following one-shot pulse after writing to the TRBPR register. 2. Do not set both the TRBPRE and TRBPR registers to 00h. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 169 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT Address 010Ah Bit Name Timer RB Output Level Select Bit Timer RB Output Sw itch Bit 0 : Outputs Outputs 1 : Outputs Outputs After Reset 00h Function one-shot pulse "H" "L" w hen the timer is stopped one-shot pulse "L" "H" w hen the timer is stopped Set to 0 in programmable one-shot generation mode. INOSTG One-Shot Trigger Control Bit(1) INOSEG One-Shot Trigger Polarity Select Bit(1) -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, its content is 0. 0 : INT0 pin one-shot trigger disabled _____ 1 : INT0 pin one-shot trigger enabled 0 : Falling edge trigger 1 : Rising edge trigger TRBIOC Register in Programmable One-Shot Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 170 of 453 RW RW _____ NOTE: 1. Refer to 14.2.3.1 One-Shot Trigger Selection. Figure 14.20 RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Set to 0 when counting ends Set to 1 by program TOSSTF bit in TRBOCR register Set to 1 by INT0 pin input trigger 1 0 INT0 pin input Count source Timer RB prescaler underflow signal Count starts 01h Counter of timer RB Timer RB primary reloads 00h Count starts 01h Timer RB primary reloads 00h 01h Set to 0 when interrupt request is acknowledged, or set by program IR bit in TRBIC register 1 0 Set to 0 by program TOPL bit in TRBIOC register 1 0 Waveform output starts Waveform output ends Waveform output starts 1 TRBIO pin output 0 The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h TRBIOC register TOPL = 0, TOCNT = 0 INOSTG = 1 (INT0 one-shot trigger enabled) INOSEG = 1 (edge trigger at rising edge) Figure 14.21 Operating Example of Programmable One-Shot Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 171 of 453 Waveform output ends R8C/26 Group, R8C/27 Group 14.2.3.1 14. Timers One-Shot Trigger Selection In programmable one-shot generation mode and programmable wait one-shot generation mode, operation starts when a one-shot trigger is generated while the TCSTF bit in the TRBCR register is set to 1 (count starts). A one-shot trigger can be generated by either of the following causes: * 1 is written to the TOSST bit in the TRBOCR register by a program. * Trigger input from the INT0 pin. When a one-shot trigger occurs, the TOSSTF bit in the TRBOCR register is set to 1 (one-shot operation in progress) after one or two cycles of the count source have elapsed. Then, in programmable one-shot generation mode, count operation begins and one-shot waveform output starts. (In programmable wait one-shot generation mode, count operation starts for the wait period.) If a one-shot trigger occurs while the TOSSTF bit is set to 1, no retriggering occurs. To use trigger input from the INT0 pin, input the trigger after making the following settings: * Set the PD4_5 bit in the PD4 register to 0 (input port). * Select the INT0 digital filter with bits INT0F1 and INT0F0 in the INTF register. * Select both edges or one edge with the INT0PL bit in INTEN register. If one edge is selected, further select falling or rising edge with the INOSEG bit in TRBIOC register. * Set the INT0EN bit in the INTEN register to 0 (enabled). * After completing the above, set the INOSTG bit in the TRBIOC register to 1 (INT pin one-shot trigger enabled). Note the following points with regard to generating interrupt requests by trigger input from the INT0 pin. * Processing to handle the interrupts is required. Refer to 12. Interrupts, for details. * If one edge is selected, use the POL bit in the INT0IC register to select falling or rising edge. (The INOSEG bit in the TRBIOC register does not affect INT0 interrupts). * If a one-shot trigger occurs while the TOSSTF bit is set to 1, timer RB operation is not affected, but the value of the IR bit in the INT0IC register changes. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 172 of 453 R8C/26 Group, R8C/27 Group 14.2.4 14. Timers Programmable Wait One-Shot Generation Mode In programmable wait one-shot generation mode, a one-shot pulse is output from the TRBO pin by a program or an external trigger input (input to the INT0 pin) (refer to Table 14.10 Specifications of Programmable Wait One-Shot Generation Mode). When a trigger is generated from that point, the timer outputs a pulse only once for a given length of time equal to the setting value in the TRBSC register after waiting for a given length of time equal to the setting value in the TRBPR register. Figure 14.22 shows the TRBIOC Register in Programmable Wait One-Shot Generation Mode. Figure 14.23 shows an Operating Example of Programmable Wait One-Shot Generation Mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 173 of 453 R8C/26 Group, R8C/27 Group Table 14.10 14. Timers Specifications of Programmable Wait One-Shot Generation Mode Item Count sources Count operations Specification f1, f2, f8, timer RA underflow * Decrement the timer RB primary setting value. * When a count of the timer RB primary underflows, the timer reloads the contents of timer RB secondary before the count continues. * When a count of the timer RB secondary underflows, the timer reloads the contents of timer RB primary before the count completes and the TOSSTF bit is set to 0 (one-shot stops). * When the count stops, the timer reloads the contents of the reload register before it stops. Wait time (n+1)(m+1)/fi fi: Count source frequency n: Value set in the TRBPRE register, m Value set in the TRBPR register(2) One-shot pulse output time (n+1)(p+1)/fi fi: Count source frequency n: Value set in the TRBPRE register, p: Value set in the TRBSC register Count start conditions * The TSTART bit in the TRBCR register is set to 1 (count starts) and the next trigger is generated. * Set the TOSST bit in the TRBOCR register to 1 (one-shot starts). * Input trigger to the INT0 pin Count stop conditions * When reloading completes after timer RB underflows during secondary period. * When the TOSSP bit in the TRBOCR register is set to 1 (one-shot stops). * When the TSTART bit in the TRBCR register is set to 0 (starts counting). * When the TSTOP bit in the TRBCR register is set to 1 (forcibly stops counting). Interrupt request In half a cycle of the count source after timer RB underflows during generation timing secondary period (complete at the same time as waveform output from the TRBO pin) [timer RB interrupt] TRBO pin function Pulse output INT0 pin functions Read from timer Write to timer Select functions * When the INOSTG bit in the TRBIOC register is set to 0 (INT0 one-shot trigger disabled): programmable I/O port or INT0 interrupt input * When the INOSTG bit in the TRBIOC register is set to 1 (INT0 one-shot trigger enabled): external trigger (INT0 interrupt input) The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE, TRBSC, and TRBPR are written while the count stops, values are written to both the reload register and counter. * When registers TRBPRE, TRBSC, and TRBPR are written to during count operation, values are written to the reload registers only.(1) * Output level select function The TOPL bit in the TRBIOC register selects the output level of the oneshot pulse waveform. * One-shot trigger select function Refer to 14.2.3.1 One-Shot Trigger Selection. * TRBO pin select function P3_1 or P1_3 is selected by the TRBOSEL bit in the PINSR2 register. NOTES: 1. The set value is reflected at the following one-shot pulse after writing to registers TRBSC and TRBPR. 2. Do not set both the TRBPRE and TRBPR registers to 00h. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 174 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT Address 010Ah Bit Name Timer RB output level select 0 : Outputs bit Outputs w ait. 1 : Outputs Outputs w ait. Timer RB output sw itch bit After Reset 00h Function one-shot pulse "H". "L" w hen the timer stops or during one-shot pulse "L". "H" w hen the timer stops or during Set to 0 in programmable w ait one-shot generation mode. RW RW RW _____ INOSTG INOSEG -- (b7-b4) One-shot trigger control bit(1) 0 : INT0 pin one-shot trigger disabled _____ 1 : INT0 pin one-shot trigger enabled 0 : Falling edge trigger One-shot trigger polarity 1 : Rising edge trigger select bit(1) Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. Refer to 14.2.3.1 One-Shot Trigger Selection. Figure 14.22 TRBIOC Register in Programmable Wait One-Shot Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 175 of 453 RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Set to 1 by setting 1 to TOSST bit in TRBOCR register, or INT0 pin input trigger. TOSSTF bit in TRBOCR register Set to 0 when counting ends 1 0 INT0 pin input Count source Timer RB prescaler underflow signal Count starts Counter of timer RB 01h Timer RB secondary reloads 00h 04h Timer RB primary reloads 03h 02h 01h 00h 01h Set to 0 when interrupt request is acknowledged, or set by program. IR bit in TRBIC register 1 TOPL bit in TRBIOC register 1 0 Set to 0 by program 0 Wait starts Waveform output starts Waveform output ends 1 TRBIO pin output 0 Wait (primary period) One-shot pulse (secondary period) The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h, TRBSC = 04h INOSTG = 1 (INT0 one-shot trigger enabled) INOSEG = 1 (edge trigger at rising edge) Figure 14.23 Operating Example of Programmable Wait One-Shot Generation Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 176 of 453 R8C/26 Group, R8C/27 Group 14.2.5 14. Timers Notes on Timer RB * Timer RB stops counting after a reset. Set the values in the timer RB and timer RB prescalers before the count starts. * Even if the prescaler and timer RB is read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In programmable one-shot generation mode and programmable wait one-shot generation mode, when setting the TSTART bit in the TRBCR register to 0, 0 (stops counting) or setting the TOSSP bit in the TRBOCR register to 1 (stops one-shot), the timer reloads the value of reload register and stops. Therefore, in programmable one-shot generation mode and programmable wait one-shot generation mode, read the timer count value before the timer stops. * The TCSTF bit remains 0 (count stops) for 1 to 2 cycles of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RB(1)other than the TCSTF bit. Timer RB starts counting at the first valid edge of the count source after the TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 1 to 2 cycles of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RB counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RB: TRBCR, TRBOCR, TRBIOC, TRBMR, TRBPRE, TRBSC, and TRBPR. * If the TSTOP bit in the TRBCR register is set to 1 during timer operation, timer RB stops immediately. * If 1 is written to the TOSST or TOSSP bit in the TRBOCR register, the value of the TOSSTF bit changes after one or two cycles of the count source have elapsed. If the TOSSP bit is written to 1 during the period between when the TOSST bit is written to 1 and when the TOSSTF bit is set to 1, the TOSSTF bit may be set to either 0 or 1 depending on the content state. Likewise, if the TOSST bit is written to 1 during the period between when the TOSSP bit is written to 1 and when the TOSSTF bit is set to 0, the TOSSTF bit may be set to either 0 or 1. 14.2.5.1 Timer mode The following workaround should be performed in timer mode. To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 177 of 453 R8C/26 Group, R8C/27 Group 14.2.5.2 14. Timers Programmable waveform generation mode The following three workarounds should be performed in programmable waveform generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) To change registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), synchronize the TRBO output cycle using a timer RB interrupt, etc. This operation should be preformed only once in the same output cycle. Also, make sure that writing to the TRBPR register does not occur during period A shown in Figures 14.24 and 14.25. The following shows the detailed workaround examples. * Workaround example (a): As shown in Figure 14.24, write to registers TRBSC and TRBPR in the timer RB interrupt routine. These write operations must be completed by the beginning of period A. Period A Count source/ prescaler underflow signal TRBO pin output IR bit in TRBIC register Primary period (a) Interrupt request is acknowledged Secondary period Ensure sufficient time (b) Interrupt request is generated Instruction in Interrupt sequence interrupt routine Set the secondary and then the primary register immediately (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (assuming no wait states and that a register is set as the divisor). (b) 20 cycles. 21 cycles for address match and single-step interrupts. Figure 14.24 Workaround Example (a) When Timer RB interrupt is Used Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 178 of 453 R8C/26 Group, R8C/27 Group 14. Timers * Workaround example (b): As shown in Figure 14.25 detect the start of the primary period by the TRBO pin output level and write to registers TRBSC and TRBPR. These write operations must be completed by the beginning of period A. If the port register's bit value is read after the port direction register's bit corresponding to the TRBO pin is set to 0 (input mode), the read value indicates the TRBO pin output value. Period A Count source/ prescaler underflow signal TRBO pin output Read value of the port register's bit corresponding to the TRBO pin (when the bit in the port direction register is set to 0) Secondary period Primary period (i) (ii) (iii) Ensure sufficient time The TRBO output inversion is detected at the end of the secondary period. Figure 14.25 Upon detecting (i), set the secondary and then the primary register immediately. Workaround Example (b) When TRBO Pin Output Value is Read (3) To stop the timer counting in the primary period, use the TSTOP bit in the TRBCR register. In this case, registers TRBPRE and TRBPR are initialized and their values are set to the values after reset. 14.2.5.3 Programmable one-shot generation mode The following two workarounds should be performed in programmable one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 179 of 453 R8C/26 Group, R8C/27 Group 14.2.5.4 14. Timers Programmable wait one-shot generation mode The following three workarounds should be performed in programmable wait one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. (3) Set registers TRBSC and TRBPR using the following procedure. (a) To use "INT0 pin one-shot trigger enabled" as the count start condition Set the TRBSC register and then the TRBPR register. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before trigger input from the INT0 pin. (b) To use "writing 1 to TOSST bit" as the start condition Set the TRBSC register, the TRBPR register, and then TOSST bit. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before writing to the TOSST bit. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 180 of 453 R8C/26 Group, R8C/27 Group 14.3 14. Timers Timer RC 14.3.1 Overview Timer RC is a 16-bit timer with four I/O pins. Timer RC uses either f1 or fOCO40M as its operation clock. Table 14.11 lists the Timer RC Operation Clock. Table 14.11 Timer RC Operation Clock Condition Timer RC Operation Clock Count source is f1, f2, f4, f8, f32, or TRCCLK input (bits TCK2 to TCK0 in f1 TRCCR1 register are set to a value from 000b to 101b) Count source is fOCO40M (bits TCK2 to TCK0 in TRCCR1 register are set fOCO40M to 110b) Table 14.12 lists the Timer RC I/O Pins, and Figure 14.26 shows a Timer RC Block Diagram. Timer RC has three modes. * Timer mode - Input capture function The counter value is captured to a register, using an external signal as the trigger. - Output compare function Matches between the counter and register values are detected. (Pin output state changes when a match is detected.) The following two modes use the output compare function. * PWM mode Pulses of a given width are output continuously. * PWM2 mode A one-shot waveform or PWM waveform is output following the trigger after the wait time has elapsed. Input capture function, output compare function, and PWM mode settings may be specified independently for each pin. In PWM2 mode waveforms are output based on a combination of the counter or the register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 181 of 453 R8C/26 Group, R8C/27 Group 14. Timers f1, f2, f4, f8, f32, fOCO40M TRCMR register TRCCR1 register TRCIER register INT0 Count source select circuit TRCSR register TRCIOR0 register TRCIOA/TRCTRG TRCIOR1 register Data bus TRCCLK TRCIOB Timer RC control circuit TRC register TRCGRA register TRCIOC TRCIOD TRCGRB register TRCGRC register TRCGRD register TRCCR2 register TRCDF register Timer RC interrupt request TRCOER register Figure 14.26 Table 14.12 Timer RC Block Diagram Timer RC I/O Pins Pin Name TRCIOA(P1_1) TRCIOB(P1_2) TRCIOC(P5_3 or P3_4)(1) TRCIOD(P5_4 or P3_5)(1) TRCCLK(P3_3) TRCTRG(P1_1) I/O I/O Function Function differs according to the mode. Refer to descriptions of individual modes for details Input Input External clock input PWM2 mode external trigger input NOTE: 1. The pins used for TRCIOC and TRCIOD are selectable. Refer to the description of the bits TRCIOCSEL and TRCIODSEL in the PINSR3 register in Figure 7.10 Registers PINSR1, PINSR2, and PINSR3 for details. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 182 of 453 R8C/26 Group, R8C/27 Group 14.3.2 14. Timers Registers Associated with Timer RC Table 14.13 lists the Registers Associated with Timer RC. Figures 14.27 to 14.36 show details of the registers associated with timer RC. Table 14.13 Registers Associated with Timer RC 0120h TRCMR Mode Timer Output Input PWM Capture Compare Function Function Valid Valid Valid 0121h TRCCR1 Valid Valid Valid Valid 0122h TRCIER Valid Valid Valid Valid 0123h TRCSR Valid Valid Valid Valid 0124h TRCIOR0 Valid Valid - - 0125h TRCIOR1 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh 0130h TRC Valid Valid Valid Valid TRCGRA Valid Valid Valid Valid TRCCR2 - - - Valid 0131h TRCDF Valid - - Valid 0132h TRCOER - Valid Valid Valid Address Symbol PWM2 Valid TRCGRB Related Information Timer RC mode register Figure 14.27 TRCMR Register Timer RC control register 1 Figure 14.28 TRCCR1 Register Figure 14.49 TRCCR1 Register for Output Compare Function Figure 14.52 TRCCR1 Register in PWM Mode Figure 14.56 TRCCR1 Register in PWM2 Mode Timer RC interrupt enable register Figure 14.29 TRCIER Register Timer RC status register Figure 14.30 TRCSR Register Timer RC I/O control register 0, timer RC I/O control register 1 Figure 14.36 Registers TRCIOR0 and TRCIOR1 Figure 14.43 TRCIOR0 Register for Input Capture Function Figure 14.44 TRCIOR1 Register for Input Capture Function Figure 14.47 TRCIOR0 Register for Output Compare Function Figure 14.48 TRCIOR1 Register for Output Compare Function Timer RC counter Figure 14.31 TRC Register Timer RC general registers A, B, C, and D Figure 14.32 Registers TRCGRA, TRCGRB, TRCGRC, and TRCGRD TRCGRC TRCGRD - : Invalid Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 183 of 453 Timer RC control register 2 Figure 14.33 TRCCR2 Register Timer RC digital filter function select register Figure 14.34 TRCDF Register Timer RC output mask enable register Figure 14.35 TRCOER Register R8C/26 Group, R8C/27 Group 14. Timers Timer RC Mode Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCMR Bit Symbol Address 0120h Bit Name PWM mode of TRCIOB select bit(2) After Reset 01001000b Function RW 0 : Timer mode 1 : PWM mode RW PWM mode of TRCIOD select bit 0 : Timer mode 1 : PWM mode RW PWM2 mode select bit 0 : PWM 2 mode 1 : Timer mode or PWM mode RW BFC TRCGRC register function select bit(3) 0 : General register 1 : Buffer register of TRCGRA register RW BFD TRCGRD register function select bit 0 : General register 1 : Buffer register of TRCGRB register RW -- (b6) Nothing is assigned. If necessary, set to 0. When read, the content is 1. PWMB (2) PWMC PWM mode of TRCIOC select bit (2) PWMD PWM2 TSTART TRC count start bit 0 : Count stops 1 : Count starts NOTES: 1. For notes on PWM2 mode, refer to 14.3.9.5 TRCMR Register in PWM2 Mode . 2. These bits are enabled w hen the PWM2 bit is set to 1 (timer mode or PWM mode). 3. Set the BFC bit to 0 (general register) in PWM2 mode. Figure 14.27 TRCMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : Timer mode 1 : PWM mode Page 184 of 453 -- RW R8C/26 Group, R8C/27 Group 14. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) After Reset 00h Function Function varies according to the operating mode (function).(2) RW RW (1) TOB TRCIOB output level select bit RW (1) TOC TRCIOC output level select bit RW (1) TOD TRCIOD output level select bit Count source select bits (1) RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 TCK1 TCK2 TRC counter clear select bit(2, 3) CCLR 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. RW 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. Bits CCLR, TOA, TOB, TOC and TOD are disabled for the input capture function of the timer mode. 3. The TRC counter performs free-running operation for the input capture function of the timer mode independent of the CCLR bit setting. Figure 14.28 TRCCR1 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 185 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC Interrupt Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCIER Address 0122h After Reset 01110000b Bit Symbol Bit Name Function IMIEA IMIEB IMIEC IMIED -- (b6-b4) Input capture / compare match interrupt enable bit A 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit RW Input capture / compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture / compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture / compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. Overflow interrupt enable bit OVIE Figure 14.29 TRCIER Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Page 186 of 453 0 : Disable interrupt (OVI) by the OVF bit 1 : Enable interrupt (OVI) by the OVF bit -- RW R8C/26 Group, R8C/27 Group 14. Timers Timer RC Status Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCSR Bit Symbol IMFA Address 0123h Bit Name Input capture / compare match flag A After Reset 01110000b Function [Source for setting this bit to 0] Write 0 after read.(1) [Source for setting this bit to 1] Refer to the table below . Input capture / compare match flag B IMFC Input capture / compare match flag C RW IMFD Input capture / compare match flag D RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- Overflow flag OVF [Source for setting this bit to 0] Write 0 after read.(1) [Source for setting this bit to 1] Refer to the table below . NOTE: 1. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit. (This bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0.) * This bit remains unchanged if 1 is w ritten to it. IMFA IMFB IMFC IMFD OVF Timer Mode PWM Mode PWM2 Mode Input capture Function Output Compare Function TRCIOA pin input edge(1) When the values of the registers TRC and TRCGRA match. TRCIOB pin input edge(1) When the values of the registers TRC and TRCGRB match. TRCIOC pin input edge(1) When the values of the registers TRC and TRCGRC match.(2) TRCIOD pin input edge(1) When the values of the registers TRC and TRCGRD match.(2) When the TRC register overflow s. NOTES: 1. Edge selected by bits IOj1 to IOj0 (j = A, B, C, or D). 2. Includes the condition that bits BFC and BFD are set to 1 (buffer registers of registers TRCGRA and TRCGRB). Figure 14.30 TRCSR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW IMFB -- (b6-b4) Bit Symbol RW Page 187 of 453 RW RW R8C/26 Group, R8C/27 Group 14. Timers Timer RC Counter(1) (b15) b7 (b8) b0 b7 b0 Symbol TRC Address 0127h-0126h After Reset 0000h Setting Range Function Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRCSR register is set to 1. RW 0000h to FFFFh RW NOTE: 1. Access the TRC register in 16-bit units. Do not access it in 8-bit units. Figure 14.31 TRC Register Timer RC General Register A, B, C and D(1) (b15) b7 (b8) b0 b7 b0 Symbol TRCGRA TRCGRB TRCGRC TRCGRD Address 0129h-0128h 012Bh-012Ah 012Dh-012Ch 012Fh-012Eh Function Function varies according to the operating mode. NOTE: 1. Access registers TRCGRA to TRCGRD in 16-bit units. Do not access them in 8-bit units. Figure 14.32 Registers TRCGRA, TRCGRB, TRCGRC, and TRCGRD Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 188 of 453 After Reset FFFFh FFFFh FFFFh FFFFh RW RW R8C/26 Group, R8C/27 Group 14. Timers Timer RC Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR2 Address 0130h After Reset 00011111b Bit Symbol Bit Name Function -- (b4-b0) CSEL Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRC count operation select bit(1, 2) 0 : Count continues at compare match w ith the TRCGRA register 1 : Count stops at compare match w ith the TRCGRA register TRCTRG input edge select bits (3) b7 b6 TCEG0 TCEG1 0 0 : Disable the trigger input from the TRCTRG pin 0 1 : Rising edge selected 1 0 : Falling edge selected 1 1 : Both edges selected RW -- RW RW RW NOTES: 1. For notes on PWM2 mode, refer to 14.3.9.5 TRCMR Register in PWM2 Mode. 2. In timer mode and PWM mode this bit is disabled (the count operation continues independent of the CSEL bit setting). 3. In timer mode and PWM mode these bits are disabled. Figure 14.33 TRCCR2 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 189 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC Digital Filter Function Select Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCDF Bit Symbol DFA Address 0131h Bit Name TRCIOA pin digital filter function select bit(1) After Reset 00h Function 0 : Function is not used 1 : Function is used RW RW DFB TRCIOB pin digital filter function select bit(1) RW DFC TRCIOC pin digital filter function select bit(1) RW DFD TRCIOD pin digital filter function select bit(1) RW DFTRG TRCTRG pin digital filter function select bit(2) RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- -- (b5) DFCK0 Clock select bits for digital filter function(1, 2) DFCK1 b7 b6 0 0 1 1 0 : f32 1 : f8 0 : f1 1 : Count source (clock selected by bits TCK2 to TCK0 in the TRCCR1 register) RW RW NOTES: 1. These bits are enabled for the input capture function. 2. These bits are enabled w hen in PWM2 mode and bits TCEG1 to TCEG0 in the TRCCR2 register are set to 01b, 10b, or 11b (TRCTRG trigger input enabled). Figure 14.34 TRCDF Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 190 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC Output Master Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCOER Bit Symbol Address 0132h Bit Name TRCIOA output disable bit(1) EA TRCIOB output disable bit(1) EB TRCIOC output disable bit(1) EC TRCIOD output disable bit(1) ED -- (b6-b4) After Reset 01111111b Function RW 0 : Enable output 1 : Disable output (The TRCIOA pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOB pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOC pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOD pin is used as a programmable I/O port.) RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- _____ PTO INT0 of pulse output forced cutoff signal input enabled bit 0 : Pulse output forced cutoff input disabled 1 : Pulse output forced cutoff input enabled (Bits EA, EB, EC, and ED are set to 1 (disable output) w hen "L" is applied to the _____ INT0 pin) NOTE: 1. These bits are disabled for input pins set to the input capture function. Figure 14.35 TRCOER Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 191 of 453 RW R8C/26 Group, R8C/27 Group 14. Timers Timer RC I/O Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address TRCIOR0 0124h Bit Symbol Bit Name IOA0 TRCGRA control bits IOA1 TRCGRA mode select bit(2) IOA2 IOA3 IOB0 IOB1 IOB2 -- (b7) After Reset 10001000b Function Function varies according to the operating mode (function). RW RW RW 0 : Output compare function 1 : Input capture function RW TRCGRA input capture input sw itch bit(4) 0 : fOCO128 signal 1 : TRCIOA pin input RW TRCGRB control bits Function varies according to the operating mode (function). RW RW TRCGRB mode select bit(3) 0 : Output compare function 1 : Input capture function RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. The TRCIOR0 register is enabled in timer mode. It is disabled in modes PWM and PWM2. 2. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 3. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. 4. The IOA3 bit is enabled w hen the IOA2 bit is set to 1 (input capture function). Timer RC I/O Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address TRCIOR1 0125h Bit Symbol Bit Name IOC0 TRCGRC control bits IOC1 TRCGRC mode select bit(2) IOC2 After Reset 10001000b Function Function varies according to the operating mode (function). 0 : Output compare function 1 : Input capture function Nothing is assigned. If necessary, set to 0. When read, the content is 1. IOD0 IOD1 TRCGRD control bits Function varies according to the operating mode (function). RW RW TRCGRD mode select bit(3) 0 : Output compare function 1 : Input capture function RW -- (b7) Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. The TRCIOR1 register is enabled in timer mode. It is disabled in modes PWM and PWM2. 2. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 3. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Registers TRCIOR0 and TRCIOR1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW -- (b3) IOD2 Figure 14.36 RW RW RW Page 192 of 453 -- -- R8C/26 Group, R8C/27 Group 14.3.3 14. Timers Common Items for Multiple Modes 14.3.3.1 Count Source The method of selecting the count source is common to all modes. Table 14.14 lists the Count Source Selection, and Figure 14.37 shows a Count Source Block Diagram. Table 14.14 Count Source Selection Count Source f1, f2, f4, f8, f32 fOCO40M Selection Method Count source selected using bits TCK2 to TCK0 in TRCCR1 register FRA00 bit in FRA0 register set to 1 (high-speed on-chip oscillator on) and bits TCK2 to TCK0 in TRCCR1 register are set to 110b (fOCO40M) External signal input Bits TCK2 to TCK0 in TRCCR1 register are set to 101b (count source is rising edge to TRCCLK pin of external clock) and PD3_3 bit in PD3 register is set to 0 (input mode) TCK2 to TCK0 f1 = 000b = 001b f2 = 010b f4 Count source = 011b f8 TRC register = 100b f32 = 101b TRCCLK = 110b fOCO40M TCK2 to TCK0: Bits in TRCCR1 register Figure 14.37 Count Source Block Diagram The pulse width of the external clock input to the TRCCLK pin should be three cycles or more of the timer RC operation clock (refer to Table 14.11 Timer RC Operation Clock). To select fOCO40M as the count source, set the FRA00 bit in the FRA0 register set to 1 (high-speed on-chip oscillator on), and then set bits TCK2 to TCK0 in the TRCCR1 register to 110b (fOCO40M). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 193 of 453 R8C/26 Group, R8C/27 Group 14.3.3.2 14. Timers Buffer Operation Bits BFC and BFD in the TRCMR register are used to select the TRCGRC or TRCGRD register as the buffer register for the TRCGRA or TRCGRB register. * Buffer register for TRCGRA register: TRCGRC register * Buffer register for TRCGRB register: TRCGRD register Buffer operation differs depending on the mode. Table 14.15 lists the Buffer Operation in Each Mode, Figure 14.38 shows the Buffer Operation for Input Capture Function, and Figure 14.39 shows the Buffer Operation for Output Compare Function. Table 14.15 Buffer Operation in Each Mode Function, Mode Input capture function Transfer Timing Input capture signal input Transfer Destination Register Contents of TRCGRA (TRCGRB) register are transferred to buffer register Contents of buffer register are transferred to TRCGRA (TRCGRB) register Contents of buffer register (TRCGRD) are transferred to TRCGRB register Output compare function Compare match between TRC register and TRCGRA (TRCGRB) PWM mode register PWM2 mode * Compare match between TRC register and TRCGRA register * TRCTRG pin trigger input TRCIOA input (input capture signal) TRCGRC register TRCGRA register TRC TRCIOA input TRC register n n-1 n+1 Transfer TRCGRA register m n Transfer TRCGRC register (buffer) m The above applies under the following conditions: * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 100b (input capture at the rising edge). Figure 14.38 Buffer Operation for Input Capture Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 194 of 453 R8C/26 Group, R8C/27 Group 14. Timers Compare match signal TRCGRC register TRC register TRCGRA register TRCGRA register Comparator m m-1 TRC m+1 m n Transfer TRCGRC register (buffer) n TRCIOA output The above applies under the following conditions: * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 001b ("L" output at compare match). Figure 14.39 Buffer Operation for Output Compare Function Make the following settings in timer mode. * To use the TRCGRC register as the buffer register for the TRCGRA register: Set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. * To use the TRCGRD register as the buffer register for the TRCGRB register: Set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. The output compare function, PWM mode, or PWM2 mode, and the TRCGRC or TRCGRD register is functioning as a buffer register, the IMFC bit or IMFD bit in the TRCSR register is set to 1 when a compare match with the TRC register occurs. The input capture function and the TRCGRC register or TRCGRD register is functioning as a buffer register, the IMFC bit or IMFD bit in the TRCSR register is set to 1 at the input edge of a signal input to the TRCIOC pin or TRCIOD pin. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 195 of 453 R8C/26 Group, R8C/27 Group 14.3.3.3 14. Timers Digital Filter The input to TRCTRG or TRCIOj (j = A, B, C, or D) is sampled, and the level is considered to be determined when three matches occur. The digital filter function and sampling clock are selected using the TRCDF register. Figure 14.40 shows a Block Diagram of Digital Filter. TCK2 to TCK0 f1 f2 f4 f8 f32 TRCCLK DFCK1 to DFCK0 = 000b = 00b f32 = 001b = 01b f8 = 010b = 10b f1 = 011b = 11b Count source = 100b IOA2 to IOA0 IOB2 to IOB0 IOC2 to IOC0 IOD2 to IOD0 (or TCEG1 to TCEG0) = 101b = 110b fOCO40M Sampling clock DFj (or DFTRG) C TRCIOj input signal (or TRCTRG input signal) D C Q Latch C D Q Latch D 1 C Q Latch D Q Match detect circuit Edge detect circuit Latch 0 Timer RC operation clock f1 or fOCO40M C D Q Latch Clock cycle selected by TCK2 to TCK0 (or DFCK1 to DFCK0) Sampling clock TRCIOj input signal (or TRCTRG input signal) Three matches occur and a signal change is confirmed. Input signal after passing through digital filter Maximum signal transmission delay is five sampling clock pulses. If fewer than three matches occur, the matches are treated as noise and no transmission is performed. j = A, B, C, or D TCK0 to TCK2: Bits in TRCCR1 register DFTRG, DFCK0 to DFCK1, DFj: Bits in TRCDF register IOA0 to IOA2, IOB0 to IOB2: Bits in TRCIOR0 register IOC0 to IOC2, IOD0 to IOD2: Bits in TRCIOR1 register TCEG1 to TCEG0: Bits in TRCCR2 register Figure 14.40 Block Diagram of Digital Filter Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 196 of 453 R8C/26 Group, R8C/27 Group 14.3.3.4 14. Timers Forced Cutoff of Pulse Output When using the timer mode's output compare function, the PWM mode, or the PWM2 mode, pulse output from the TRCIOj (j = A, B, C, or D) output pin can be forcibly cut off and the TRCIOj pin set to function as a programmable I/O port by means of input to the INT0 pin. A pin used for output by the timer mode's output compare function, the PWM mode, or the PWM2 mode can be set to function as the timer RC output pin by setting the Ej bit in the TRCOER register to 0 (timer RC output enabled). If "L" is input to the INT0 pin while the PTO bit in the TRCOER register is set to 1 (pulse output forced cutoff signal input INT0 enabled), bits EA, EB, EC, and ED in the TRCOER register are all set to 1 (timer RC output disabled, TRCIOj output pin functions as the programmable I/O port). When one or two cycles of the timer RC operation clock after "L" input to the INT0 pin (refer to Table 14.11 Timer RC Operation Clock) has elapsed, the TRCIOj output pin becomes a programmable I/O port. Make the following settings to use this function. * Set the pin state following forced cutoff of pulse output (high impedance (input), "L" output, or "H" output) (refer to 7. Programmable I/O Ports). * Set the INT0EN bit to 1 (INT0 input enabled) and the INT0PL bit to 0 (one edge) in the INTEN register. * Set the PD4_5 bit in the PD4 register to 0 (input mode). * Select the INT0 digital filter by means of bits INT0F1 to INT0F0 in the INTF register. * Set the PTO bit in the TRCOER register to 1 (pulse output forced cutoff signal input INT0 enabled). The IR bit in the INT0IC register is set to 1 (interrupt request) in accordance with the setting of the POL bit and a change in the INT0 pin input (refer to 12.6 Notes on Interrupts). For details on interrupts, refer to 12. Interrupts. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 197 of 453 R8C/26 Group, R8C/27 Group 14. Timers EA bit write value INT0 input EA bit D Q S Timer RC output data TRCIOA Port P1_1 output data PTO bit Port P1_1 input data EB bit write value EB bit D Q S Timer RC output data TRCIOB Port P1_2 output data Port P1_2 input data EC bit write value EC bit D Q S Timer RC output data TRCIOC Port P5_3 (P3_4)(1) output data ED bit write value Port P5_3 (P3_4)(1) input data ED bit D Q S Timer RC output data Port P5_4 (P3_5)(1) output data Port P5_4 (P3_5)(1) input data EA, EB, EC, ED, PTO: Bits in TRCOER register NOTE: 1. The pin in parentheses ( ) can be assigned by a program. Figure 14.41 Forced Cutoff of Pulse Output Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 198 of 453 TRCIOD R8C/26 Group, R8C/27 Group 14.3.4 14. Timers Timer Mode (Input Capture Function) This function measures the width or period of an external signal. An external signal input to the TRCIOj (j = A, B, C, or D) pin acts as a trigger for transferring the contents of the TRC register (counter) to the TRCGRj register (input capture). The input capture function, or any other mode or function, can be selected for each individual pin. The TRCGRA register can also select fOCO128 signal as input-capture trigger input. Table 14.16 lists the Specifications of Input Capture Function, Figure 14.42 shows a Block Diagram of Input Capture Function, Figures 14.43 and 14.44 show the registers associated with the input capture function, Table 14.17 lists the Functions of TRCGRj Register when Using Input Capture Function, and Figure 14.45 shows an Operating Example of Input Capture Function. Table 14.16 Specifications of Input Capture Function Item Count source Count operation Count period Count start condition Count stop condition Interrupt request generation timing TRCIOA, TRCIOB, TRCIOC, and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment 1/fk x 65,536 fk: Count source frequency 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. The TRC register retains a value before count stops. * Input capture (valid edge of TRCIOj input or fOCO128 signal edge) * The TRC register overflows. Programmable I/O port or input capture input (selectable individually by pin) Programmable I/O port or INT0 interrupt input The count value can be read by reading TRC register. The TRC register can be written to. * Input capture input pin select One or more of pins TRCIOA, TRCIOB, TRCIOC, and TRCIOD * Input capture input valid edge selected Rising edge, falling edge, or both rising and falling edges * Buffer operation (Refer to 14.3.3.2 Buffer Operation.) * Digital filter (Refer to 14.3.3.3 Digital Filter.) * Input-capture trigger selected fOCO128 can be selected for input-capture trigger input of the TRCGRA register. j = A, B, C, or D Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 199 of 453 R8C/26 Group, R8C/27 Group fOCO Divided by 128 14. Timers fOCO128 IOA3 = 0 Input capture signal(3) TRCIOA IOA3 = 1 (Note 1) TRCGRA register TRC register TRCGRC register TRCIOC Input capture signal Input capture signal TRCIOB (Note 2) TRCGRB register TRCGRD register TRCIOD Input capture signal IOA3: Bit in TRCIOR0 register NOTES: 1. The BFC bit in the TRCMR register is set to 1 (TRCGRC register functions as the buffer register for the TRCGRA register) 2. The BFD bit in the TRCMR register is set to 1 (TRCGRD register functions as the buffer register for the TRCGRB register) 3. The trigger input of the TRCGRA register can select the TRCIOA pin input or fOCO128 signal. Figure 14.42 Block Diagram of Input Capture Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 200 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC I/O Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRCIOR0 Bit Symbol Address 0124h Bit Name TRCGRA control bits IOA1 IOA3 RW TRCGRA input capture input sw itch bit(3) 0 : fOCO128 signal 1 : TRCIOA pin input RW TRCGRB control bits b5 b4 0 0 : Input capture to the TRCGRB register at the rising edge 0 1 : Input capture to the TRCGRB register at the falling edge 1 0 : Input capture to the TRCGRB register at both edges 1 1 : Do not set. TRCGRB mode select bit(2) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. 3. The IOA3 bit is enabled w hen the IOA2 bit is set to 1 (input capture function). Figure 14.43 TRCIOR0 Register for Input Capture Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Set to 1 (input capture) in the input capture function. IOB1 -- (b7) RW TRCGRA mode select bit(1) IOB0 IOB2 RW b1 b0 0 0 : Input capture to the TRCGRA register at the rising edge 0 1 : Input capture to the TRCGRA register at the falling edge 1 0 : Input capture to the TRCGRA register at both edges 1 1 : Do not set. IOA0 IOA2 After Reset 10001000b Function Page 201 of 453 RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Timer RC I/O Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRCIOR1 Bit Symbol Address 0125h Bit Name TRCGRC control bits After Reset 10001000b Function 0 0 : Input capture to the TRCGRC register at the rising edge 0 1 : Input capture to the TRCGRC register at the falling edge 1 0 : Input capture to the TRCGRC register at both edges 1 1 : Do not set. IOC0 IOC1 IOC2 -- (b3) TRCGRC mode select bit(1) RW RW RW -- b5 b4 0 0 : Input capture to the TRCGRD register at the rising edge 0 1 : Input capture to the TRCGRD register at the falling edge 1 0 : Input capture to the TRCGRD register at both edges 1 1 : Do not set. IOD0 IOD1 -- (b7) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRCGRD control bits IOD2 RW b1 b0 TRCGRD mode select bit(2) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW RW -- NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 14.44 Table 14.17 TRCIOR1 Register for Input Capture Function Functions of TRCGRj Register when Using Input Capture Function Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC TRCGRD Setting - BFC = 0 BFD = 0 BFC = 1 BFD = 1 Input Capture Input Pin General register. Can be used to read the TRC register value TRCIOA at input capture. TRCIOB General register. Can be used to read the TRC register value TRCIOC at input capture. TRCIOD Buffer registers. Can be used to hold transferred value from TRCIOA the general register. (Refer to 14.3.3.2 Buffer Operation.) TRCIOB Register Function j = A, B, C, or D BFC, BFD: Bits in TRCMR register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 202 of 453 R8C/26 Group, R8C/27 Group 14. Timers TRCCLK input count source TRC register count value FFFFh 0006h 0003h 0000h TSTART bit in TRCMR register 1 0 65536 TRCIOA input TRCGRA register 0006h Transfer TRCGRC register 0003h Transfer 0006h IMFA bit in TRCSR register 1 OVF bit in TRCSR register 1 0 Set to 0 by a program 0 The above applies under the following conditions: * Bits TCK2 to TCK0 in the TRCCR1 register are set to 101b (the count source is TRCCLK input). * Bits IOA2 to IOA0 in the TRCIORA register are set to 101b (input capture at the falling edge of the TRCIOA input). * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). Figure 14.45 Operating Example of Input Capture Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 203 of 453 R8C/26 Group, R8C/27 Group 14.3.5 14. Timers Timer Mode (Output Compare Function) This function detects when the contents of the TRC register (counter) and the TRCGRj register (j = A, B, C, or D) match (compare match). When a match occurs a signal is output from the TRCIOj pin at a given level. The output compare function, or other mode or function, can be selected for each individual pin. Table 14.18 lists the Specifications of Output Compare Function, Figure 14.46 shows a Block Diagram of Output Compare Function, Figures 14.47 to 14.49 show the registers associated with the output compare function, Table 14.19 lists the Functions of TRCGRj Register when Using Output Compare Function, and Figure 14.50 shows an Operating Example of Output Compare Function. Table 14.18 Specifications of Output Compare Function Item Count source Count operation Count period Waveform output timing Count start condition Count stop condition Interrupt request generation timing TRCIOA, TRCIOB, TRCIOC, and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment * The CCLR bit in the TRCCR1 register is set to 0 (free running operation): 1/fk x 65,536 fk: Count source frequency * The CCLR bit in the TRCCR1 register is set to 1 (TRC register set to 0000h at TRCGRA compare match): 1/fk x (n + 1) n: TRCGRA register setting value Compare match 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. The output compare output pin retains output level before count stops, the TRC register retains a value before count stops. * Compare match (contents of registers TRC and TRCGRj match) * The TRC register overflows. Programmable I/O port or output compare output (selectable individually by pin) Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRC register. The TRC register can be written to. * Output compare output pin selected One or more of pins TRCIOA, TRCIOB, TRCIOC, and TRCIOD * Compare match output level select "L" output, "H" output, or toggle output * Initial output level select Sets output level for period from count start to compare match * Timing for clearing the TRC register to 0000h Overflow or compare match with the TRCGRA register * Buffer operation (Refer to 14.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 14.3.3.4 Forced Cutoff of Pulse Output.) * Can be used as an internal timer by disabling timer RC output j = A, B, C, or D Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 204 of 453 R8C/26 Group, R8C/27 Group 14. Timers TRC TRCIOA TRCIOC TRCIOB TRCIOD Figure 14.46 Output control Output control Output control Output control Compare match signal TRCGRA Comparator TRCGRC Comparator TRCGRB Comparator TRCGRD Compare match signal Compare match signal Compare match signal Block Diagram of Output Compare Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Comparator Page 205 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC I/O Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 Symbol TRCIOR0 Bit Symbol Address 0124h Bit Name TRCGRA control bits IOA1 IOA3 TRCGRA mode select bit(1) Set to 0 (output compare) in the output compare function. TRCGRA input capture input sw itch bit Set to 1. TRCGRB control bits b5 b4 0 0 : Disable pin output by compare match (TRCIOB pin functions as the programmable I/O port) 0 1 : "L" output by compare match in the TRCGRB register 1 0 : "H" output by compare match in the TRCGRB register 1 1 : Toggle output by compare match in the TRCGRB register IOB0 IOB1 IOB2 -- (b7) TRCGRB mode select bit(2) Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 14.47 TRCIOR0 Register for Output Compare Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 206 of 453 RW b1 b0 0 0 : Disable pin output by compare match (TRCIOA pin functions as the programmable I/O port) 0 1 : "L" output by compare match in the TRCGRA register 1 0 : "H" output by compare match in the TRCGRA register 1 1 : Toggle output by compare match in the TRCGRA register IOA0 IOA2 After Reset 10001000b Function RW RW RW RW RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Timer RC I/O Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRCIOR1 Bit Symbol Address 0125h Bit Name TRCGRC control bits IOC1 -- (b3) TRCGRC mode select bit(1) IOD1 -- (b7) TRCGRD mode select bit(2) Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 14.48 TRCIOR1 Register for Output Compare Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 207 of 453 RW RW RW -- b5 b4 0 0 : Disable pin output by compare match 0 1 : "L" output by compare match in the TRCGRD register 1 0 : "H" output by compare match in the TRCGRD register 1 1 : Toggle output by compare match in the TRCGRD register IOD0 IOD2 Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRCGRD control bits RW b1 b0 0 0 : Disable pin output by compare match 0 1 : "L" output by compare match in the TRCGRC register 1 0 : "H" output by compare match in the TRCGRC register 1 1 : Toggle output by compare match in the TRCGRC register IOC0 IOC2 After Reset 10001000b Function RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1, 2) After Reset 00h Function 0 : Initial output "L" 1 : Initial output "H" RW RW (1, 2) TOB TRCIOB output level select bit RW (1, 2) TOC TRCIOC output level select bit RW (1, 2) TOD TRCIOD output level select bit Count source select bits (1) RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 TCK1 TCK2 TRC counter clear select bit CCLR 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. RW 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 7.13 to 7.16, Tables 7.26 to 7.29, and Tables 7.37 to 7.40), the initial output level is output w hen the TRCCR1 register is set. Figure 14.49 Table 14.19 TRCCR1 Register for Output Compare Function Functions of TRCGRj Register when Using Output Compare Function Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC TRCGRD Setting Register Function - General register. Write a compare value to one of these registers. BFC = 0 BFD = 0 BFC = 1 BFD = 1 General register. Write a compare value to one of these registers. Buffer register. Write the next compare value to one of these registers. (Refer to 14.3.3.2 Buffer Operation.) j = A, B, C, or D BFC, BFD: Bits in TRCMR register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 208 of 453 Output Compare Output Pin TRCIOA TRCIOB TRCIOC TRCIOD TRCIOA TRCIOB R8C/26 Group, R8C/27 Group 14. Timers Count source TRC register value m n p Count restarts Count stops TSTART bit in TRCMR register 1 0 m+1 m+1 Output level held TRCIOA output Output inverted at compare match Initial output "L" IMFA bit in TRCSR register 1 0 Set to 0 by a program Output level held n+1 TRCIOB output "H" output at compare match Initial output "L" IMFB bit in TRCSR register 1 0 Set to 0 by a program P+1 Output level held "L" output at compare match TRCIOC output Initial output "H" IMFC bit in TRCSR register 1 0 Set to 0 by a program m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * Bits BFC and BFD in the TRCMR register are set to 0 (TRCGRC and TRCGRD do not operate as buffers). * Bits EA, EB, and EC in the TRCOER register are set to 0 (output from TRCIOA, TRCIOB, and TRCIOC enabled). * The CCLR bit in the TRCCR1 register is set to 1 (set the TRC register to 0000h by TRCGRA compare match). * In the TRCCR1 register, bits TOA and TOB are set to 0 ("L" initial output until compare match) and the TOC bit is set to 1 ("H" initial output until compare match). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 011b (TRCIOA output inverted at TRCGRA compare match). * Bits IOB2 to IOB0 in the TRCIOR0 register are set to 010b ("H" TRCIOB output at TRCGRB compare match). * Bits IOC2 to IOC2 in the TRCIOR1 register are set to 001b ("L" TRCIOC output at TRCGRC compare match). Figure 14.50 Operating Example of Output Compare Function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 209 of 453 R8C/26 Group, R8C/27 Group 14.3.6 14. Timers PWM Mode This mode outputs PWM waveforms. A maximum of three PWM waveforms with the same period are output. The PWM mode, or the timer mode, can be selected for each individual pin. (However, since the TRCGRA register is used when using any pin for the PWM mode, the TRCGRA register cannot be used for the timer mode.) Table 14.20 lists the Specifications of PWM Mode, Figure 14.51 shows a Block Diagram of PWM Mode, Figure 14.52 shows the register associated with the PWM mode, Table 14.21 lists the Functions of TRCGRj Register in PWM Mode, and Figures 14.53 and 14.54 show Operating Examples of PWM Mode. Table 14.20 Specifications of PWM Mode Item Count source Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment PWM period: 1/fk x (m + 1) Active level width: 1/fk x (m - n) Inactive width: 1/fk x (n + 1) fk: Count source frequency m: TRCGRA register setting value n: TRCGRj register setting value Count operation PWM waveform m+1 n+1 Count start condition Count stop condition Interrupt request generation timing TRCIOA pin function TRCIOB, TRCIOC, and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions ("L" is active level) 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. PWM output pin retains output level before count stops, TRC register retains value before count stops. * Compare match (contents of registers TRC and TRCGRh match) * The TRC register overflows. Programmable I/O port Programmable I/O port or PWM output (selectable individually by pin) Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRC register. The TRC register can be written to. * One to three pins selectable as PWM output pins per channel One or more of pins TRCIOB, TRCIOC, and TRCIOD * Active level selectable by individual pin * Buffer operation (Refer to 14.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 14.3.3.4 Forced Cutoff of Pulse Output.) j = B, C, or D h = A, B, C, or D Rev.2.10 Sep 26, 2008 REJ09B0278-0210 m-n Page 210 of 453 R8C/26 Group, R8C/27 Group 14. Timers TRC Compare match signal Comparator TRCIOB TRCGRA Compare match signal (Note 1) Output control TRCIOC Comparator TRCGRB Comparator TRCGRC Compare match signal TRCIOD (Note 2) Compare match signal Comparator TRCGRD NOTES: 1. The BFC bit in the TRCMR register is set to 1 (TRCGRC register functions as the buffer register for the TRCGRA register) 2. The BFD bit in the TRCMR register is set to 1 (TRCGRD register functions as the buffer register for the TRCGRB register) Figure 14.51 Block Diagram of PWM Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 211 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) (1, 2) TRCIOB output level select bit TOB TRCIOC output level select bit(1, 2) TOC TRCIOD output level select bit(1, 2) TOD Count source select bits (1) After Reset 00h Function Disabled in PWM mode TCK1 TCK2 TRC counter clear select bit CCLR RW 0 : Active level "H" (Initial output "L" "H" output by compare match in the TRCGRj register "L" output by compare match in the TRCGRA register 1 : Active level "L" (Initial output "H" "L" output by compare match in the TRCGRj register "H" output by compare match in the TRCGRA register RW RW RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 RW 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW RW j = B, C or D NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Table 7.15, Table 7.16, Tables 7.26 to 7.29, and Tables 7.37 to 7.40), the initial output level is output w hen the TRCCR1 register is set. Figure 14.52 Table 14.21 TRCCR1 Register in PWM Mode Functions of TRCGRj Register in PWM Mode Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC Setting - - BFC = 0 BFD = 0 BFC = 1 TRCGRD BFD = 1 Register Function General register. Set the PWM period. General register. Set the PWM output change point. General register. Set the PWM output change point. Buffer register. Set the next PWM period. (Refer to 14.3.3.2 Buffer Operation.) Buffer register. Set the next PWM output change point. (Refer to 14.3.3.2 Buffer Operation.) PWM Output Pin - TRCIOB TRCIOC TRCIOD - TRCIOB j = A, B, C, or D BFC, BFD: Bits in TRCMR register NOTE: 1. The output level does not change even when a compare match occurs if the TRCGRA register value (PWM period) is the same as the TRCGRB, TRCGRC, or TRCGRD register value. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 212 of 453 R8C/26 Group, R8C/27 Group 14. Timers Count source TRC register value m n p q m+1 n+1 Active level is "H" TRCIOB output m-n Inactive level is "L" p+1 m-p "L" initial output until compare match TRCIOC output q+1 m-q Active level is "L" TRCIOD output "H" initial output until compare match IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 IMFD bit in TRCSR register 1 0 Set to 0 by a program Set to 0 by a program 0 0 Set to 0 by a program Set to 0 by a program 0 m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value q: TRCGRD register setting value The above applies under the following conditions: * Bits BFC and BFD in the TRCMR register are set to 0 (registers TRCGRC and TRCGRD do not operate as buffers). * Bits EB, EC, and ED in the TRCOER register are set to 0 (output from TRCIOB, TRCIOC, and TRCIOD enabled). * In the TRCCR1 register, bits TOB and TOC are set to 0 (active level is "H") and the TOD bit is set to 1 (active level is "L"). Figure 14.53 Operating Example of PWM Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 213 of 453 R8C/26 Group, R8C/27 Group 14. Timers TRC register value p m q n 0000h TSTART bit in TRCMR register 1 TRCIOB output does not switch to "L" because no compare match with the TRCGRB register has occurred 0 Duty 0% TRCIOB output n TRCGRB register q p (p>m) Rewritten by a program IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 0 Set to 0 by a program Set to 0 by a program 0 TRC register value m p n 0000h TSTART bit in TRCMR register 1 If compare matches occur simultaneously with registers TRCGRA and TRCGRB, the compare match with the TRCGRB register has priority. TRCIOB output switches to "L". (In other words, no change). 0 Duty 100% TRCIOB output TRCIOB output switches to "L" at compare match with the TRCGRB register. (In other words, no change). TRCGRB register m n IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 p Rewritten by a program 0 Set to 0 by a program Set to 0 by a program 0 m: TRCGRA register setting value The above applies under the following conditions: * The EB bit in the TRCOER register is set to 0 (output from TRCIOB enabled). * The TOB bit in the TRCCR1 register is set to 1 (active level is "L"). Figure 14.54 Operating Example of PWM Mode (Duty 0% and Duty 100%) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 214 of 453 R8C/26 Group, R8C/27 Group 14.3.7 14. Timers PWM2 Mode This mode outputs a single PWM waveform. After a given wait duration has elapsed following the trigger, the pin output switches to active level. Then, after a given duration, the output switches back to inactive level. Furthermore, the counter stops at the same time the output returns to inactive level, making it possible to use PWM2 mode to output a programmable wait one-shot waveform. Since timer RC uses multiple general registers in PWM2 mode, other modes cannot be used in conjunction with it. Figure 14.55 shows a Block Diagram of PWM2 Mode, Table 14.22 lists the Specifications of PWM2 Mode, Figure 14.56 shows the register associated with PWM2 mode, Table 14.23 lists the Functions of TRCGRj Register in PWM2 Mode, and Figures 14.57 to 14.59 show Operating Examples of PWM2 Mode. Trigger signal Compare match signal TRCTRG TRCIOB Input control Count clear signal TRC (Note 1) Comparator TRCGRA Comparator TRCGRB Comparator TRCGRC TRCGRD register Output control NOTE: 1. The BFD bit in the TRCMR register is set to 1 (the TRCGRD register functions as the buffer register for the TRCGRB register). Figure 14.55 Block Diagram of PWM2 Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 215 of 453 R8C/26 Group, R8C/27 Group Table 14.22 14. Timers Specifications of PWM2 Mode Item Count source Count operation PWM waveform Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment TRC register PWM period: 1/fk x (m + 1) (no TRCTRG input) Active level width: 1/fk x (n - p) Wait time from count start or trigger: 1/fk x (p + 1) fk: Count source frequency m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value TRCTRG input m+1 n+1 n+1 p+1 p+1 TRCIOB output n-p n-p (TRCTRG: Rising edge, active level is "H") Count start conditions Count stop conditions Interrupt request generation timing TRCIOA/TRCTRG pin function TRCIOB pin function TRCIOC and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions * Bits TCEG1 to TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger disabled) or the CSEL bit in the TRCCR2 register is set to 0 (count continues). 1 (count starts) is written to the TSTART bit in the TRCMR register. * Bits TCEG1 to TCEG0 in the TRCCR2 register are set to 01b, 10b, or 11b (TRCTRG trigger enabled) and the TSTART bit in the TRCMR register is set to 1 (count starts). A trigger is input to the TRCTRG pin * 0 (count stops) is written to the TSTART bit in the TRCMR register while the CSEL bit in the TRCCR2 register is set to 0 or 1. The TRCIOB pin outputs the initial level in accordance with the value of the TOB bit in the TRCCR1 register. The TRC register retains the value before count stops. * The count stops due to a compare match with TRCGRA while the CSEL bit in the TRCCR2 register is set to 1 The TRCIOB pin outputs the initial level. The TRC register retains the value before count stops if the CCLR bit in the TRCCR1 register is set to 0. The TRC register is set to 0000h if the CCLR bit in the TRCCR1 register is set to 1. * Compare match (contents of TRC and TRCGRj registers match) * The TRC register overflows Programmable I/O port or TRCTRG input PWM output Programmable I/O port Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRC register. The TRC register can be written to. * External trigger and valid edge selected The edge or edges of the signal input to the TRCTRG pin can be used as the PWM output trigger: rising edge, falling edge, or both rising and falling edges * Buffer operation (Refer to 14.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 14.3.3.4 Forced Cutoff of Pulse Output.) * Digital filter (Refer to 14.3.3.3 Digital Filter.) j = A, B, or C Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 216 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) (1, 2) TRCIOB output level select bit TOB TOC TOD TRCIOC output level select bit(1) After Reset 00h Function Disabled in the PWM2 mode 0 : Active level "H" (Initial output "L" "H" output by compare match in the TRCGRC register "L" output by compare match in the TRCGRB register 1 : Active level "L" (Initial output "H" "L" output by compare match in the TRCGRC register "H" output by compare match in the TRCGRB register Disabled in the PWM2 mode TRCIOD output level select bit(1) Count source select bits (1) TCK1 TCK2 TRC counter clear select bit CCLR RW RW RW RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 RW 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Table 7.15 and Table 7.16), the initial output level is output w hen the TRCCR1 register is set. Figure 14.56 Table 14.23 TRCCR1 Register in PWM2 Mode Functions of TRCGRj Register in PWM2 Mode Register TRCGRA TRCGRB TRCGRC Setting - - BFC = 0 TRCGRD TRCGRD BFD = 0 BFD = 1 Register Function PWM2 Output Pin General register. Set the PWM period. TRCIOB pin General register. Set the PWM output change point. General register. Set the PWM output change point (wait time after trigger). (Not used in PWM2 mode) - Buffer register. Set the next PWM output change point. (Refer to TRCIOB pin 14.3.3.2 Buffer Operation.) j = A, B, C, or D BFC, BFD: Bits in TRCMR register NOTE: 1. Do not set the TRCGRB and TRCGRC registers to the same value. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 217 of 453 R8C/26 Group, R8C/27 Group 14. Timers Count source TRC register value FFFFh TRC register cleared at TRCGRA register compare match m n Previous value held if the TSTRAT bit is set to 0 Set to 0000h by a program p 0000h TSTART bit in TRCMR register Count stops because the CSEL bit is set to 1 1 0 Set to 1 by a program CSEL bit in TRCCR2 register TSTART bit is set to 0 1 0 m+1 n+1 p+1 "H" output at TRCGRC register compare match p+1 Return to initial output if the TSTART bit is set to 0 "L" initial output TRCIOB output "L" output at TRCGRB register compare match No change No change "H" output at TRCGRC register compare match IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 0 Set to 0 by a program 0 Set to 0 by a program Set to 0 by a program 0 TRCGRB register n Transfer TRCGRD register n Transfer Next data Transfer from buffer register to general register m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger input disabled). Figure 14.57 Operating Example of PWM2 Mode (TRCTRG Trigger Input Disabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 218 of 453 R8C/26 Group, R8C/27 Group 14. Timers Count source TRC register value TRC register cleared at TRCGRA register compare match FFFFh m TRC register (counter) cleared at TRCTRG pin trigger input Previous value held if the TSTART bit is set to 0 n Set to 0000h by a program p 0000h TRCTRG input Count starts at TRCTRG pin trigger input Count starts when TSTART bit is set to 1 TSTART bit in TRCMR register 1 CSEL bit in TRCCR2 register 1 Count stops because the CSEL bit is set to 1 Changed by a program The TSTART bit is set to 0 0 Set to 1 by a program 0 m+1 n+1 n+1 p+1 p+1 "H" output at TRCGRC register compare match "L" output at TRCGRB register compare match "L" initial output TRCIOB output IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 TRCGRB register p+1 Inactive level so TRCTRG input is enabled Return to initial value if the TSTART bit is set to 0 Active level so TRCTRG input is disabled 0 Set to 0 by a program 0 Set to 0 by a program Set to 0 by a program Set to 0 by a program 0 n n n Transfer TRCGRD register Transfer n Transfer from buffer register to general register n Transfer Transfer Next data Transfer from buffer register to general register m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 11b (trigger at both rising and falling edges of TRCTRG input). Figure 14.58 Operating Example of PWM2 Mode (TRCTRG Trigger Input Enabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 219 of 453 R8C/26 Group, R8C/27 Group 14. Timers * TRCGRB register setting value greater than TRCGRA register setting value TRC register value * TRCGRC register setting value greater than TRCGRA register setting value TRC register value n p m m n p 0000h 0000h TSTART bit in TRCMR register 1 TSTART bit in TRCMR register 0 n+1 m+1 m+1 TRCIOB output "H" output at TRCGRC register compare match 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register "L" initial output 0 0 1 0 p+1 No compare match with TRCGRB register, so "H" output continues IMFA bit in TRCSR register 1 No compare match with TRCGRC register, so "L" output continues TRCIOB output IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 Set to 0 by a program 0 "L" output at TRCGRB register compare match with no change "L" initial output 0 0 0 m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger input disabled). Figure 14.59 Operating Example of PWM2 Mode (Duty 0% and Duty 100%) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 220 of 453 R8C/26 Group, R8C/27 Group 14.3.8 14. Timers Timer RC Interrupt Timer RC generates a timer RC interrupt request from five sources. The timer RC interrupt uses the single TRCIC register (bits IR and ILVL0 to ILVL2) and a single vector. Table 14.24 lists the Registers Associated with Timer RC Interrupt, and Figure 14.60 shows a Block Diagram of Timer RC Interrupt. Table 14.24 Registers Associated with Timer RC Interrupt Timer RC Status Register TRCSR Timer RC Interrupt Enable Register TRCIER Timer RC Interrupt Control Register TRCIC IMFA bit IMIEA bit Timer RC interrupt request (IR bit in TRCIC register) IMFB bit IMIEB bit IMFC bit IMIEC bit IMFD bit IMIED bit OVF bit OVIE bit IMFA, IMFB, IMFC, IMFD, OVF: Bits in TRCSR register IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRCIER register Figure 14.60 Block Diagram of Timer RC Interrupt Like other maskable interrupts, the timer RC interrupt is controlled by the combination of the I flag, IR bit, bits ILVL0 to ILVL2, and IPL. However, it differs from other maskable interrupts in the following respects because a single interrupt source (timer RC interrupt) is generated from multiple interrupt request sources. * The IR bit in the TRCIC register is set to 1 (interrupt requested) when a bit in the TRCSR register is set to 1 and the corresponding bit in the TRCIER register is also set to 1 (interrupt enabled). * The IR bit is set to 0 (no interrupt request) when the bit in the TRCSR register or the corresponding bit in the TRCIER register is set to 0, or both are set to 0. In other words, the interrupt request is not maintained if the IR bit is once set to 1 but the interrupt is not acknowledged. * If after the IR bit is set to 1 another interrupt source is triggered, the IR bit remains set to 1 and does not change. * If multiple bits in the TRCIER register are set to 1, use the TRCSR register to determine the source of the interrupt request. * The bits in the TRCSR register are not automatically set to 0 when an interrupt is acknowledged. Set them to 0 within the interrupt routine. Refer to Figure 14.30 TRCSR Register, for the procedure for setting these bits to 0. Refer to Figure 14.29 TRCIER Register, for details of the TRCIER register. Refer to 12.1.6 Interrupt Control, for details of the TRCIC register and 12.1.5.2 Relocatable Vector Tables, for information on interrupt vectors. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 221 of 453 R8C/26 Group, R8C/27 Group 14.3.9 14. Timers Notes on Timer RC 14.3.9.1 TRC Register * The following note applies when the CCLR bit in the TRCCR1 register is set to 1 (clear TRC register at compare match with TRCGRA register). When using a program to write a value to the TRC register while the TSTART bit in the TRCMR register is set to 1 (count starts), ensure that the write does not overlap with the timing with which the TRC register is set to 0000h. If the timing of the write to the TRC register and the setting of the TRC register to 0000h coincide, the write value will not be written to the TRC register and the TRC register will be set to 0000h. * Reading from the TRC register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.W #XXXXh, TRC ;Write JMP.B L1 ;JMP.B instruction L1: MOV.W TRC,DATA ;Read 14.3.9.2 TRCSR Register Reading from the TRCSR register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.B #XXh, TRCSR ;Write JMP.B L1 ;JMP.B instruction L1: MOV.B TRCSR,DATA ;Read 14.3.9.3 Count Source Switching * Stop the count before switching the count source. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. * After switching the count source from fOCO40M to another clock, allow a minimum of two cycles of f1 to elapse after changing the clock setting before stopping fOCO40M. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. (3) Wait for a minimum of two cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator off). 14.3.9.4 Input Capture Function * The pulse width of the input capture signal should be three cycles or more of the timer RC operation clock (refer to Table 14.11 Timer RC Operation Clock). * The value of the TRC register is transferred to the TRCGRj register one or two cycles of the timer RC operation clock after the input capture signal is input to the TRCIOj (j = A, B, C, or D) pin (when the digital filter function is not used). 14.3.9.5 TRCMR Register in PWM2 Mode When the CSEL bit in the TRCCR2 register is set to 1 (count stops at compare match with the TRCGRA register), do not set the TRCMR register at compare match timing of registers TRC and TRCGRA. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 222 of 453 R8C/26 Group, R8C/27 Group 14.4 14. Timers Timer RE Timer RE has the 4-bit counter and 8-bit counter. Timer RE has the following 2 modes: * Real-time clock mode Generate 1-second signal from fC4 and count seconds, minutes, hours, and days of the week. * Output compare mode Count a count source and detect compare matches. (For J, K version, timer RE can be used only in output compare mode.) The count source for timer RE is the operating clock that regulates the timing of timer operations. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 223 of 453 R8C/26 Group, R8C/27 Group 14.4.1 14. Timers Real-Time Clock Mode (For N, D Version Only) In real-time clock mode, a 1-second signal is generated from fC4 using a divide-by-2 frequency divider, 4-bit counter, and 8-bit counter and used to count seconds, minutes, hours, and days of the week. Figure 14.61 shows a Block Diagram of Real-Time Clock Mode and Table 14.25 lists the Specifications of Real-Time Clock Mode. Figures 14.62 to 14.66 and 14.68 and 14.69 show the registers associated with real-time clock mode. Table 14.26 lists the Interrupt Sources, Figure 14.67 shows the Definition of Time Representation, and Figure 14.70 shows the Operating Example in Real-Time Clock Mode. 1/2 fC4 (1/16) (1/256) 4-bit counter 8-bit counter (1s) Overflow Data bus Overflow TRESEC register Overflow TREMIN register Overflow TREHR register H12_H24 bit TREWK register 000 PM bit WKIE DYIE Timing control HRIE INT bit MNIE SEIE BSY bit H12_H24, PM, INT: Bits in TRECR1 register BSY: Bit in registers TRESEC, TREMIN, TREHR, and TREWK Figure 14.61 Block Diagram of Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 224 of 453 Timer RE interrupt R8C/26 Group, R8C/27 Group Table 14.25 14. Timers Specifications of Real-Time Clock Mode Item Count source Count operation Count start condition Count stop condition Interrupt request generation timing TREO pin function Read from timer Write to timer Select function Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Specification fC4 Increment 1 (count starts) is written to TSTART bit in TRECR1 register 0 (count stops) is written to TSTART bit in TRECR1 register Select any one of the following: * Update second data * Update minute data * Update hour data * Update day of week data * When day of week data is set to 000b (Sunday) Programmable I/O ports or output of f2, f4, or f8 When reading TRESEC, TREMIN, TREHR, or TREWK register, the count value can be read. The values read from registers TRESEC, TREMIN, and TREHR are represented by the BCD code. When bits TSTART and TCSTF in the TRECR1 register are set to 0 (timer stops), the value can be written to registers TRESEC, TREMIN, TREHR, and TREWK. The values written to registers TRESEC, TREMIN, and TREHR are represented by the BCD codes. * 12-hour mode/24-hour mode switch function Page 225 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RE Second Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRESEC Address 0118h After Reset 00h Bit Symbol Bit Name Function SC00 SC01 SC02 SC03 SC10 SC11 SC12 1st digit of second count bits Count 0 to 9 every second. When the 0 to 9 digit moves up, 1 is added to the 2nd (BCD digit of second. code) 2nd digit of second count bits When counting 0 to 5, 60 seconds are counted. Timer RE busy flag This bit is set to 1 w hile registers TRESEC, TREMIN, TREHR, and TREWK are updated. BSY Figure 14.62 Setting Range 0 to 5 (BCD code) RW RW RW RW RW RW RW RW RO TRESEC Register in Real-Time Clock Mode Timer RE Minute Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TREMIN Address 0119h After Reset 00h Bit Symbol Bit Name Function MN00 MN01 MN02 MN03 MN10 MN11 MN12 1st digit of minute count bits Count 0 to 9 every minute. When the 0 to 9 digit moves up, 1 is added to the 2nd (BCD digit of minute. code) 2nd digit of minute count bits When counting 0 to 5, 60 minutes are 0 to 5 counted. (BCD code) Timer RE busy flag This bit is set to 1 w hile registers TRESEC, TREMIN, TREHR, and TREWK are updated. BSY Figure 14.63 TREMIN Register in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Setting Range Page 226 of 453 RW RW RW RW RW RW RW RW RO R8C/26 Group, R8C/27 Group 14. Timers Timer RE Hour Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TREHR Address 011Ah After Reset 00h Bit Symbol Bit Name Function HR00 HR01 HR02 HR03 HR10 1st digit of hour count bits Count 0 to 9 every hour. When the 0 to 9 digit moves up, 1 is added to the 2nd (BCD digit of hour. code) 2nd digit of hour count bits Count 0 to 1 w hen the H12_H24 bit is 0 to 2 set to 0 (12-hour mode). (BCD Count 0 to 2 w hen the H12_H24 bit is code) set to 1 (24-hour mode). HR11 -- (b6) Nothing is assigned. If necessary, set to 0. When read, the content is 0. Timer RE busy flag BSY Figure 14.64 Setting Range RW RW RW RW RW RW RW -- This bit is set to 1 w hile registers TRESEC, TREMIN, TREHR, and TREWK are updated. RO TREHR Register in Real-Time Clock Mode Timer RE Day of Week Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TREWK Address 011Bh After Reset 00h Bit Symbol Bit Name Function Day of w eek count bits WK1 WK2 -- (b6-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. Timer RE busy flag BSY Figure 14.65 TREWK Register in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 b2 b1 b0 0 0 0 : Sunday 0 0 1 : Monday 0 1 0 : Tuesday 0 1 1 : Wednesday 1 0 0 : Thursday 1 0 1 : Friday 1 1 0 : Saturday 1 1 1 : Do not set WK0 Page 227 of 453 RW This bit is set to 1 w hile registers TRESEC, TREMIN, TREHR, and TREWK are updated. RW RW RW -- RO R8C/26 Group, R8C/27 Group 14. Timers Timer RE Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRECR1 Address 011Ch After Reset 00h Bit Symbol Bit Name Function -- (b0) RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. TCSTF TOENA INT Timer RE count status flag 0 : Count stopped 1 : Counting RO TREO pin output enable bit 0 : Disable clock output 1 : Enable clock output RW Interrupt request timing bit Set to 1 in real-time clock mode. Timer RE reset bit When setting this bit to 0, after setting it to 1, the follow ings w ill occur. * Registers TRESEC, TREMIN, TREHR, TREWK, and TRECR2 are set to 00h. * Bits TCSTF, INT, PM, H12_H24, and TSTART in the TRECR1 register are set to 0. * The 8-bit counter is set to 00h and the 4-bit counter is set to 0h. RW When the H12_H24 bit is set to 0 (12-hour mode) (1) 0 : a.m. 1 : p.m. When the H12_H24 bit is set to 1 (24-hour mode), its value is undefined. RW Operating mode select bit 0 : 12-hour mode 1 : 24-hour mode RW Timer RE count start bit 0 : Count stops 1 : Count starts RW TRERST A.m./p.m. bit PM H12_H24 TSTART -- RW NOTE: 1. This bit is automatically modified w hile timer RE counts. Figure 14.66 TRECR1 Register in Real-Time Clock Mode Noon Contents of TREHR Register H12_H24 bit = 1 (24-hour mode) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 H12_H24 bit = 0 (12-hour mode) 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 0 (a.m.) Contents of PM bit 1 (p.m.) 000 (Sunday) Contents in TREWK register Date changes Contents of TREHR Register H12_H24 bit = 1 (24-hour mode) 18 19 20 21 22 23 0 1 2 3 H12_H24 bit = 0 (12-hour mode) 6 7 8 9 10 11 0 1 2 3 Contents of PM bit Contents in TREWK register 1 (p.m.) 0 (a.m.) 000 (Sunday) 001 (Monday) PM bit and H12_H24 bits: Bits in TRECR1 register The above applies to the case when count starts from a.m. 0 on Sunday. Figure 14.67 Definition of Time Representation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 228 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RE Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRECR2 Address 011Dh After Reset 00h Bit Symbol Bit Name Function SEIE MNIE HRIE DYIE WKIE COMIE -- (b7-b6) RW Periodic interrupt triggered every second enable bit(1) 0 : Disable periodic interrupt triggered every second 1 : Enable periodic interrupt triggered every second RW Periodic interrupt triggered every minute enable bit(1) 0 : Disable periodic interrupt triggered every minute 1 : Enable periodic interrupt triggered every minute RW Periodic interrupt triggered every hour enable bit(1) 0 : Disable periodic interrupt triggered every hour 1 : Enable periodic interrupt triggered every hour RW Periodic interrupt triggered every day 0 : Disable periodic interrupt triggered enable bit(1) every day 1 : Enable periodic interrupt triggered every day RW Periodic interrupt triggered every w eek enable bit(1) 0 : Disable periodic interrupt triggered every w eek 1 : Enable periodic interrupt triggered every w eek Compare match interrupt enable bit Set to 0 in real-time clock mode. RW RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTE: 1. Do not set multiple enable bits to 1 (enable interrupt). Figure 14.68 Table 14.26 TRECR2 Register in Real-Time Clock Mode Interrupt Sources Factor Periodic interrupt triggered every week Periodic interrupt triggered every day Periodic interrupt triggered every hour Periodic interrupt triggered every minute Periodic interrupt triggered every second Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Interrupt Source Value in TREWK register is set to 000b (Sunday) (1-week period) TREWK register is updated (1-day period) Interrupt Enable Bit WKIE DYIE TREHR register is updated (1-hour period) HRIE TREMIN register is updated (1-minute period) MNIE TRESEC register is updated (1-second period) SEIE Page 229 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RE Count Source Select Register b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 0 Symbol TRECSR Address 011Eh After Reset 00001000b Bit Symbol Bit Name Function RCS0 Count source select bits Set to 00b in real-time clock mode. RCS1 RCS2 RCS3 -- (b4) 4-bit counter select bit Set to 0 in real-time clock mode. Real-time clock mode select bit Set to 1 in real-time clock mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Clock output select bits (1) Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. Write to bits RCS5 to RCS6 w hen the TOENA bit in the TRECR1 register is set to 0 (disable clock output). TRECSR Register in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 230 of 453 RW RW -- b6 b5 0 0 : f2 0 1 : f4 1 0 : f8 1 1 : Do not set. RCS6 Figure 14.69 RW RW RCS5 -- (b7) RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers 1s Approx. 62.5 ms Approx. 62.5 ms BSY bit Bits SC12 to SC00 in TRESEC register 58 59 Bits MN12 to MN00 in TREMIN register 03 Bits HR11 to HR00 in TREHR register (Not changed) PM bit in TRECR1 register IR bit in TREIC register (when SEIE bit in TRECR2 register is set to 1 (enable periodic interrupt triggered every second)) IR bit in TREIC register (when MNIE bit in TRECR2 register is set to 1 (enable periodic interrupt triggered every minute)) (Not changed) 0 (Not changed) 1 0 1 0 BSY: Bit in registers TRESEC, TREMIN, TREHR, and TREWK Figure 14.70 Operating Example in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 04 1 Bits WK2 to WK0 in TREWK register Page 231 of 453 00 Set to 0 by acknowledgement of interrupt request or a program R8C/26 Group, R8C/27 Group 14.4.2 14. Timers Output Compare Mode In output compare mode, the internal count source divided by 2 is counted using the 4-bit or 8-bit counter and compare value match is detected with the 8-bit counter. Figure 14.71 shows a Block Diagram of Output Compare Mode and Table 14.27 lists the Specifications of Output Compare Mode. Figures 14.72 to 14.76 show the registers associated with output compare mode, and Figure 14.77 shows the Operating Example in Output Compare Mode. f4 f8 RCS6 to RCS5 = 00b f2 = 01b RCS1 to RCS0 = 00b = 10b = 01b f32 fC4 (1) 1/2 = 10b 4-bit counter TOENA TREO pin RCS2 = 1 8-bit counter = 11b T Q = 11b R Reset RCS2 = 0 TRERST bit Comparison circuit Match signal COMIE TRERST, TOENA: Bits in TRECR1 register COMIE: Bit in TRECR2 register RCS0 to RCS2, RCS5 to RCS6: Bits in TRECSR register TRESEC TREMIN Data bus NOTE: 1. For J, K version, fC4 cannot be selected. Figure 14.71 Block Diagram of Output Compare Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 232 of 453 Timer RE interrupt R8C/26 Group, R8C/27 Group Table 14.27 14. Timers Specifications of Output Compare Mode Item Count sources Count operations Count period Count start condition Count stop condition Interrupt request generation timing TREO pin function Read from timer Write to timer Select functions Specification fC4(1) f4, f8, f32, * Increment * When the 8-bit counter content matches with the TREMIN register content, the value returns to 00h and count continues. The count value is held while count stops. * When RCS2 = 0 (4-bit counter is not used) 1/fi x 2 x (n+1) * When RCS2 = 1 (4-bit counter is used) 1/fi x 32 x (n+1) fi: Frequency of count source n: Setting value of TREMIN register 1 (count starts) is written to the TSTART bit in the TRECR1 register 0 (count stops) is written to the TSTART bit in the TRECR1 register When the 8-bit counter content matches with the TREMIN register content Select any one of the following: * Programmable I/O ports * Output f2, f4, or f8 * Compare output When reading the TRESEC register, the 8-bit counter value can be read. When reading the TREMIN register, the compare value can be read. Writing to the TRESEC register is disabled. When bits TSTART and TCSTF in the TRECR1 register are set to 0 (timer stops), writing to the TREMIN register is enabled. * Select use of 4-bit counter * Compare output function Every time the 8-bit counter value matches the TREMIN register value, TREO output polarity is reversed. The TREO pin outputs "L" after reset is deasserted and the timer RE is reset by the TRERST bit in the TRECR1 register. Output level is held by setting the TSTART bit to 0 (count stops). NOTE: 1. For J, K version, fC4 cannot be selected. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 233 of 453 R8C/26 Group, R8C/27 Group 14. Timers Timer RE Counter Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRESEC Address 0118h Function After Reset 00h RW 8-bit counter data can be read. Although Timer RE stops counting, the count value is held. The TRESEC register is set to 00h at the compare match. Figure 14.72 RO TRESEC Register in Output Compare Mode Timer RE Compare Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TREMIN Address 0119h Function 8-bit compare data is stored. Figure 14.73 TREMIN Register in Output Compare Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 234 of 453 After Reset 00h RW RW R8C/26 Group, R8C/27 Group 14. Timers Timer RE Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol TRECR1 Address 011Ch After Reset 00h Bit Symbol Bit Name Function -- (b0) TCSTF TOENA INT Nothing is assigned. If necessary, set to 0. When read, the content is 0. TSTART Figure 14.74 -- Timer RE count status flag 0 : Count stopped 1 : Counting RO TREO pin output enable bit 0 : Disable clock output 1 : Enable clock output RW Interrupt request timing bit Set to 0 in output compare mode. Timer RE reset bit When setting this bit to 0, after setting it to 1, the follow ing w ill occur. * Registers TRESEC, TREMIN, TREHR, TREWK, and TRECR2 are set to 00h. * Bits TCSTF, INT, PM, H12_H24, and TSTART in the TRECR1 register are set to 0. * The 8-bit counter is set to 00h and the 4-bit counter is set to 0h. TRERST PM H12_H24 RW A.m./p.m. bit Operating mode select bit Timer RE count start bit Set to 0 in output compare mode. 0 : Count stops 1 : Count starts RW RW RW RW RW TRECR1 Register in Output Compare Mode Timer RE Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol TRECR2 Address 011Dh After Reset 00h Bit Symbol Bit Name Function SEIE Periodic interrupt triggered every second enable bit MNIE Periodic interrupt triggered every minute enable bit RW HRIE Periodic interrupt triggered every hour enable bit RW DYIE Periodic interrupt triggered every day enable bit RW WKIE Periodic interrupt triggered every w eek enable bit RW COMIE -- (b7-b6) Figure 14.75 Compare match interrupt enable bit Set to 0 in output compare mode. 0 : Disable compare match interrupt 1 : Enable compare match interrupt Nothing is assigned. If necessary, set to 0. When read, the content is 0. TRECR2 Register in Output Compare Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Page 235 of 453 RW RW -- R8C/26 Group, R8C/27 Group 14. Timers Timer RE Count Source Select Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRECSR Address 011Eh After Reset 00001000b Bit Symbol Bit Name Function Count source select bits RCS1 RCS2 RCS3 -- (b4) 4-bit counter select bit 0 : Not used 1 : Used Real-time clock mode select bit Set to 0 in output compare mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Clock output select bits (1) RCS6 Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTES: 1. Write to bits RCS5 to RCS6 w hen the TOENA bit in the TRECR1 register is set to 0 (disable clock output). 2. For J, K version, fC4 cannot be selected. Figure 14.76 TRECSR Register in Output Compare Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 236 of 453 RW RW RW RW -- b6 b5 0 0 : f2 0 1 : f4 1 0 : f8 1 1 : Compare output RCS5 -- (b7) b1 b0 0 0 : f4 0 1 : f8 1 0 : f32 1 1 : fC4(2) RCS0 RW RW RW -- R8C/26 Group, R8C/27 Group 14. Timers 8-bit counter content (hexadecimal number) Count starts Matched TREMIN register setting value Matched Matched 00h Time Set to 1 by a program TSTART bit in TRECR1 register 1 0 2 cycles of maximum count source TCSTF bit in TRECR1 register IR bit in TREIC register TREO output 1 0 Set to 0 by acknowledgement of interrupt request or a program 1 0 1 0 Output polarity is inverted when the compare matches The above applies under the following conditions. TOENA bit in TRECR1 register = 1 (enable clock output) COMIE bit in TRECR2 register = 1 (enable compare match interrupt) RCS6 to RCS5 bits in TRECSR register = 11b (compare output) Figure 14.77 Operating Example in Output Compare Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 237 of 453 R8C/26 Group, R8C/27 Group 14.4.3 14. Timers Notes on Timer RE 14.4.3.1 Starting and Stopping Count Timer RE has the TSTART bit for instructing the count to start or stop, and the TCSTF bit, which indicates count start or stop. Bits TSTART and TCSTF are in the TRECR1 register. Timer RE starts counting and the TCSTF bit is set to 1 (count starts) when the TSTART bit is set to 1 (count starts). It takes up to 2 cycles of the count source until the TCSTF bit is set to 1 after setting the TSTART bit to 1. During this time, do not access registers associated with timer RE(1) other than the TCSTF bit. Also, timer RE stops counting when setting the TSTART bit to 0 (count stops) and the TCSTF bit is set to 0 (count stops). It takes the time for up to 2 cycles of the count source until the TCSTF bit is set to 0 after setting the TSTART bit to 0. During this time, do not access registers associated with timer RE other than the TCSTF bit. NOTE: 1. Registers associated with timer RE: TRESEC, TREMIN, TREHR, TREWK, TRECR1, TRECR2, and TRECSR. 14.4.3.2 Register Setting Write to the following registers or bits when timer RE is stopped. * Registers TRESEC, TREMIN, TREHR, TREWK, and TRECR2 * Bits H12_H24, PM, and INT in TRECR1 register * Bits RCS0 to RCS3 in TRECSR register Timer RE is stopped when bits TSTART and TCSTF in the TRECR1 register are set to 0 (timer RE stopped). Also, set all above-mentioned registers and bits (immediately before timer RE count starts) before setting the TRECR2 register. Figure 14.78 shows a Setting Example in Real-Time Clock Mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 238 of 453 R8C/26 Group, R8C/27 Group 14. Timers TSTART in TRECR1 = 0 Stop timer RE operation TCSTF in TRECR1 = 0? TREIC 00h (disable timer RE interrupt) TRERST in TRECR1 = 1 Timer RE register and control circuit reset TRERST in TRECR1 = 0 Setting of registers TRECSR, TRESEC, TREMIN, TREHR, TREWK, and bits H12_H24, PM, and INT in TRECR1 register Setting of TRECR2 Select clock output Select clock source Seconds, minutes, hours, days of week, operating mode Set a.m./p.m., interrupt timing Select interrupt source Setting of TREIC (IR bit 0, select interrupt priority level) TSTART in TRECR1 = 1 Start timer RE operation TCSTF in TRECR1 = 1? Figure 14.78 Setting Example in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 239 of 453 R8C/26 Group, R8C/27 Group 14.4.3.3 14. Timers Time Reading Procedure of Real-Time Clock Mode In real-time clock mode, read registers TRESEC, TREMIN, TREHR, and TREWK when time data is updated and read the PM bit in the TRECR1 register when the BSY bit is set to 0 (not while data is updated). Also, when reading several registers, an incorrect time will be read if data is updated before another register is read after reading any register. In order to prevent this, use the reading procedure shown below. * Using an interrupt Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register in the timer RE interrupt routine. * Monitoring with a program 1 Monitor the IR bit in the TREIC register with a program and read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register after the IR bit in the TREIC register is set to 1 (timer RE interrupt request generated). * Monitoring with a program 2 (1) Monitor the BSY bit. (2) Monitor until the BSY bit is set to 0 after the BSY bit is set to 1 (approximately 62.5 ms while the BSY bit is set to 1). (3) Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register after the BSY bit is set to 0. * Using read results if they are the same value twice (1) Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register. (2) Read the same register as (1) and compare the contents. (3) Recognize as the correct value if the contents match. If the contents do not match, repeat until the read contents match with the previous contents. Also, when reading several registers, read them as continuously as possible. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 240 of 453 R8C/26 Group, R8C/27 Group 15. Serial Interface 15. Serial Interface The serial interface consists of two channels (UART0 and UART1). Each UARTi (i = 0 or 1) has an exclusive timer to generate the transfer clock and operates independently. Figure 15.1 shows a UARTi (i = 0 or 1) Block Diagram. Figure 15.2 shows a UARTi Transmit/Receive Unit. UARTi has two modes: clock synchronous serial I/O mode and clock asynchronous serial I/O mode (UART mode). Figures 15.3 to 15.7 show the registers associated with UARTi. (UART0) TXD0 RXD0 CLK1 to CLK0 = 00b f1 f8 f32 CKDIR = 0 Internal = 01b UART reception 1/16 Clock synchronous type U0BRG register = 10b 1/(n0+1) Reception control circuit UART transmission 1/16 Transmission control circuit Clock synchronous type External CKDIR = 1 1/2 Clock synchronous type (when internal clock is selected) Clock synchronous type (when external clock is selected) Clock synchronous type (when internal clock is selected) Receive clock Transmit clock Transmit/ receive unit CKDIR = 0 CKDIR = 1 CLK polarity switch circuit CLK0 TXD1EN (UART1) RXD1 TXD1 CLK1 to CLK0 = 00b f1 f8 f32 = 01b CKDIR = 0 Internal UART reception 1/16 Clock synchronous type U1BRG register = 10b 1/(n0+1) UART transmission 1/16 Clock synchronous type External CKDIR = 1 1/2 U1PINSEL CLK1 Figure 15.1 CLK polarity switch circuit Clock synchronous type (when internal clock is selected) Clock synchronous type (when external clock is selected) Clock synchronous type (when internal clock is selected) U1PINSEL UARTi (i = 0 or 1) Block Diagram Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Reception control circuit Page 241 of 453 Transmission control circuit CKDIR=0 CKDIR=1 Receive clock Transmit clock Transmit/ receive unit R8C/26 Group, R8C/27 Group 15. Serial Interface PRYE = 0 Clock PAR disabled synchronous type 1SP RXDi SP SP Clock synchronous type UART (7 bits) UART (8 bits) UART (7 bits) UARTi receive register PAR PAR UART enabled PRYE = 1 2SP UART (9 bits) Clock synchronous type UART (8 bits) UART (9 bits) 0 0 0 0 0 0 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 UiRB register MSB/LSB conversion circuit Data bus high-order bits Data bus low-order bits MSB/LSB conversion circuit D8 PRYE = 1 PAR enabled 2SP SP SP UART (9 bits) UART D6 D5 D4 D3 D2 D1 TXDi Clock PAR disabled synchronous PRYE = 0 type 0 UARTi Transmit/Receive Unit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 D0 UiTB register UART (8 bits) UART (9 bits) Clock synchronous type PAR 1SP Figure 15.2 D7 Page 242 of 453 UART (7 bits) UART (8 bits) Clock synchronous type UART (7 bits) UARTi transmit register i = 0 or 1 SP: Stop bit PAR: Parity bit R8C/26 Group, R8C/27 Group 15. Serial Interface UARTi Transmit Buffer Register (i = 0 or 1)(1, 2) (b15) b7 (b8) b0 b7 b0 Symbol U0TB U1TB Address 00A3h-00A2h 00ABh-00AAh Function After Reset Undefined Undefined RW -- (b8-b0) Transmit data -- (b15-b9) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. WO -- NOTES: 1. When the transfer data length is 9 bits, w rite data to high byte first, then low byte. 2. Use the MOV instruction to w rite to this register. UARTi Receive Buffer Register (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol U0RB U1RB Bit Symbol -- (b7-b0) Address 00A7h-00A6h 00AFh-00AEh Bit Name -- -- (b8) -- (b11-b9) -- Overrun error flag (2) FER Framing error flag (2) PER Parity error flag (2) SUM Receive data (D8) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. (2) OER After Reset Undefined Undefined Function Receive data (D7 to D0) Error sum flag RW RO RO -- 0 : No overrun error 1 : Overrun error RO 0 : No framing error 1 : Framing error RO 0 : No parity error 1 : Parity error RO 0 : No error 1 : Error RO NOTES: 1. Read out the UiRB register in 16-bit units. 2. Bits SUM, PER, FER, and OER are set to 0 (no error) w hen bits SMD2 to SMD0 in the UiMR register are set to 000b (serial interface disabled) or the RE bit in the UiC1 register is set to 0 (receive disabled). The SUM bit is set to 0 (no error) w hen bits PER, FER, and OER are set to 0 (no error). Bits PER and FER are set to 0 even w hen the higher byte of the UiRB register is read out. Also, bits PER and FER are set to 0 w hen reading the high-order byte of the UiRB register. Figure 15.3 Registers U0TB to U1TB and U0RB to U1RB Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 243 of 453 R8C/26 Group, R8C/27 Group 15. Serial Interface UARTi Bit Rate Register (i = 0 or 1)(1, 2, 3) b7 b0 Symbol U0BRG U1BRG Address 00A1h 00A9h After Reset Undefined Undefined Function Setting Range Assuming the set value is n, UiBRG divides the count source by n+1 00h to FFh RW WO NOTES: 1. Write to this register w hile the serial I/O is neither transmitting nor receiving. 2. Use the MOV instruction to w rite to this register. 3. After setting the CLK0 to CLK1 bits of the UiC0 register, w rite to the UiBRG register. UARTi Transmit/Receive Mode Register (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol U0MR U1MR Bit Symbol Address 00A0h 00A8h Bit Name Serial I/O mode select bits SMD0 SMD2 STPS Internal/external clock select bit 0 : Internal clock 1 : External clock(1) -- (b7) RW RW RW Odd/even parity select bit Enable w hen PRYE = 1 0 : Odd parity 1 : Even parity RW Parity enable bit 0 : Parity disabled 1 : Parity enabled RW Reserved bit Set to 0. Registers U0BRG to U1BRG and U0MR to U1MR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : 1 stop bit 1 : 2 stop bits NOTE: 1. When the CLK0 pin is used, set the PD1_6 bit in the PD1 register to 0 (input). When the CLK1 pin is used, set the PD0_5 bit in the PD0 register to 0 (input). Figure 15.4 RW Stop bit length select bit PRY PRYE RW b2 b1 b0 0 0 0 : Serial interface disabled 0 0 1 : Clock synchronous serial I/O mode 1 0 0 : UART mode transfer data 7 bits long 1 0 1 : UART mode transfer data 8 bits long 1 1 0 : UART mode transfer data 9 bits long Other than above : Do not set SMD1 CKDIR After Reset 00h 00h Function Page 244 of 453 RW R8C/26 Group, R8C/27 Group 15. Serial Interface UARTi Transmit/Receive Control Register 0 (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol U0C0 U1C0 Bit Symbol CLK0 CLK1 -- (b2) TXEPT -- (b4) NCH Address 00A4h 00ACh Bit Name BRG count source select b1 b0 bits (1) 0 0 : Selects f1 0 1 : Selects f8 1 0 : Selects f32 1 1 : Do not set. Reserved bit Set to 0. Transmit register empty flag 0 : Data in transmit register (during transmit) 1 : No data in transmit register (transmit completed) Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW RW RO -- RW CLK polarity select bit 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RW Transfer format select bit 0 : LSB first 1 : MSB first Registers U0C0 to U1C0 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : TXDi pin is for CMOS output 1 : TXDi pin is for N-channel open drain output NOTE: 1. If the BRG count source is sw itched, set the UiBRG register again. Figure 15.5 RW Data output select bit CKPOL UFORM After Reset 00001000b 00001000b Function Page 245 of 453 RW R8C/26 Group, R8C/27 Group 15. Serial Interface UARTi Transmit/Receive Control Register 1 (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0C1 U1C1 Bit Symbol Address 00A5h 00ADh Bit Name Transmit enable bit(1) After Reset 00000010b 00000010b Function 0 : Disables transmission 1 : Enables transmission Transmit buffer empty flag 0 : Data in UiTB register 1 : No data in UiTB register RO Receive enable bit 0 : Disables reception 1 : Enables reception RW Receive complete flag(1) 0 : No data in UiRB register 1 : Data in UiRB register RO UiIRS UARTi transmit interrupt cause select bit 0 : Transmission buffer empty (TI=1) 1 : Transmission completed (TXEPT=1) RW UiRRM UARTi continuous receive mode enable bit(2) 0 : Disables continuous receive mode 1 : Enables continuous receive mode RW -- (b7-b6) Nothing is assigned. If necessary, set to 0. When read, the content is 0. TE TI RE RI NOTES: 1. The RI bit is set to 0 w hen the higher byte of the UiRB register is read out. 2. Set the UiRRM bit to 0 (disables continuous receive mode) in UART mode. Figure 15.6 Registers U0C1 to U1C1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 246 of 453 RW RW -- R8C/26 Group, R8C/27 Group 15. Serial Interface Pin Select Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 1 Symbol PINSR1 Bit Symbol Address 00F5h Bit Name TXD1/RXD1 pin select bit(1) After Reset 00h Function RW b1 b0 0 0 : P3_7(TXD1/RXD1) 0 1 : P3_7(TXD1), P4_5(RXD1) 1 0 : P3_6(TXD1/RXD1) 1 1 : Do not set. UART1SEL0 UART1SEL1 -- (b2) Reserved bit Set to 1. When read, the content is 0. -- (b7-b3) Reserved bits Set to 0. When read, the content is 0. RW RW RW RW NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN in the PMR register. Port Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol PMR Bit Symbol INT1SEL -- (b2-b1) SSISEL Address 00F8h Bit Name _____ INT1 pin select bit After Reset 00h Function 0 : P1_5, P1_7 1 : P3_6 Nothing is assigned. If necessary, set to 0. When read, the content is 0. SSI pin select bit (1) U1PINSEL TXD1SEL TXD1EN TXD1 pin sw itch bit Port/TXD1 pin sw itch bit TXD1/RXD1 select bit (1) (1) 2 IICSEL SSU / I C bus pin sw itch bit Pin Function 0 : P3_3 1 : P1_6 RW 0 : P0_0 1 : P3_6, P3_7 RW 0 : Programmable I/O port 1 : TXD1 RW 0 : RXD1 1 : TXD1 RW 0 : Selects SSU function 1 : Selects I2C bus function RW U1PINSEL bit PMR Register TXD1SEL bit x x 0 1 P3_7(TXD1) 00b P3_7(RXD1) P0_0(TXD1) 01b P3_7(TXD1) P4_5(RXD1) P3_6(TXD1) 10b P3_6(RXD1) P0_0(TXD1) 1 x 0 1 Registers PINSR1 and PMR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 247 of 453 x x x: 0 or 1 Figure 15.7 1 RW -- NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN, and bits UART1SEL1 and UART1SEL0 in the PINSR1 register. PINSR1 Register UART1SEL1, UART1SEL0 bit RW TXD1EN bit 1 0 x x 1 0 x R8C/26 Group, R8C/27 Group 15.1 15. Serial Interface Clock Synchronous Serial I/O Mode In the clock synchronous serial I/O mode, data is transmitted and received using a transfer clock. Table 15.1 lists the Specifications of Clock Synchronous Serial I/O Mode. Table 15.2 lists the Registers Used and Settings in Clock Synchronous Serial I/O Mode. Table 15.1 Specifications of Clock Synchronous Serial I/O Mode Item Transfer data format Transfer clocks Specification * Transfer data length: 8 bits * CKDIR bit in UiMR register is set to 0 (internal clock): fi/(2(n+1)) fi = f1, f8, f32 n = value set in U0BRG register: 00h to FFh * The CKDIR bit is set to 1 (external clock): input from CLKi pin Transmit start conditions * Before transmit starts, the following requirements must be met(1) - The TE bit in the UiC1 register is set to 1 (transmission enabled) - The TI bit in the UiC1 register is set to 0 (data in the UiTB register) Receive start conditions * Before receive starts, the following requirements must be met(1) - The RE bit in the UiC1 register is set to 1 (reception enabled) - The TE bit in the UiC1 register is set to 1 (transmission enabled) - The TI bit in the UiC1 register is set to 0 (data in the UiTB register) * When transmitting, one of the following conditions can be selected - The UiIRS bit is set to 0 (transmit buffer empty): When transferring data from the UiTB register to UARTi transmit register (when transmission starts). - The UiIRS bit is set to 1 (transmission completes): When completing data transmission from UARTi transmit register. * When receiving When data transfer from the UARTi receive register to the UiRB register (when reception completes). Interrupt request generation timing Error detection Select functions * Overrun error(2) This error occurs if the serial interface starts receiving the next data item before reading the UiRB register and receives the 7th bit of the next data. * CLK polarity selection Transfer data input/output can be selected to occur synchronously with the rising or the falling edge of the transfer clock. * LSB first, MSB first selection Whether transmitting or receiving data begins with bit 0 or begins with bit 7 can be selected. * Continuous receive mode selection Receive is enabled immediately by reading the UiRB register. i = 0 or 1 NOTES: 1. If an external clock is selected, ensure that the external clock is "H" when the CKPOL bit in the U0C0 register is set to 0 (transmit data output at falling edge and receive data input at rising edge of transfer clock), and that the external clock is "L" when the CKPOL bit is set to 1 (transmit data output at rising edge and receive data input at falling edge of transfer clock). 2. If an overrun error occurs, the receive data (b0 to b8) of the UiRB register will be undefined. The IR bit in the SiRIC register remains unchanged. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 248 of 453 R8C/26 Group, R8C/27 Group Table 15.2 Register UiTB UiRB UiBRG UiMR UiC0 UiC1 15. Serial Interface Registers Used and Settings in Clock Synchronous Serial I/O Mode(1) Bit 0 to 7 0 to 7 OER 0 to 7 SMD2 to SMD0 CKDIR CLK1 to CLK0 TXEPT NCH CKPOL UFORM TE TI RE RI UiIRS UiRRM Function Set data transmission Data reception can be read Overrun error flag Set bit rate Set to 001b Select the internal clock or external clock Select the count source in the UiBRG register Transmit register empty flag Select TXDi pin output mode Select the transfer clock polarity Select the LSB first or MSB first Set this bit to 1 to enable transmission/reception Transmit buffer empty flag Set this bit to 1 to enable reception Reception complete flag Select the UARTi transmit interrupt source Set this bit to 1 to use continuous receive mode i = 0 or 1 NOTE: 1. Set bits which are not in this table to 0 when writing to the above registers in clock synchronous serial I/O mode. Table 15.3 lists the I/O Pin Functions in Clock Synchronous Serial I/O Mode. The TXDi (i = 0 or 1) pin outputs "H" level between the operating mode selection of UARTi and transfer start. (If the NCH bit is set to 1 (N-channel open-drain output), this pin is in a high-impedance state.) Table 15.3 I/O Pin Functions in Clock Synchronous Serial I/O Mode Pin Name TXD0 (P1_4) RXD0 (P1_5) CLK0 (P1_6) TXD1 (either P0_0, P3_6, or P3_7) RXD1 (either P3_6, P3_7, or P4_5) CLK1 (P0_5) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Function Output serial data Input serial data Selection Method (Outputs dummy data when performing reception only) PD1_5 bit in PD1 register = 0 (P1_5 can be used as an input port when performing transmission only) Output transfer clock CKDIR bit in U0MR register = 0 Input transfer clock CKDIR bit in U0MR register = 1 PD1_6 bit in PD1 register = 0 Output serial data Set registers PINSR1 and PMR (refer to Figure 15.7 Registers PINSR1 and PMR) (Outputs dummy data when performing reception only) Input serial data Set registers PINSR1 and PMR (refer to Figure 15.7 Registers PINSR1 and PMR) Corresponding bit in each port direction register = 0 (Can be used as an input port when performing transmission only) Output transfer clock CKDIR bit in U1MR register = 0 Input transfer clock PD0_5 bit in PD0 register = 0 CKDIR bit in U1MR register = 1 Page 249 of 453 R8C/26 Group, R8C/27 Group 15. Serial Interface * Example of transmit timing (when internal clock is selected) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Set data in UiTB register Transfer from UiTB register to UARTi transmit register TCLK Stop pulsing because the TE bit is set to 0 CLKi D0 TXDi TXEPT bit in UiC0 register 1 0 IR bit in SiTIC register 1 0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Set to 0 when interrupt request is acknowledged, or set by a program TC = TCLK = 2(n+1)/fi fi: Frequency of UiBRG count source (f1, f8, f32) The above applies under the following settings: n: Setting value to UiBRG register * CKDIR bit in UiMR register = 0 (internal clock) * CKPOL bit in UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) * UiIRS bit in UiC1 register = 0 (an interrupt request is generated when the transmit buffer is empty) * Example of receive timing (when external clock is selected) RE bit in UiC1 register 1 0 TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write dummy data to UiTB register Transfer from UiTB register to UARTi transmit register 1/fEXT CLKi Receive data is taken in D0 RXDi D1 D2 D3 D4 D5 D6 D7 D0 D1 Transfer from UARTi receive register to UiRB register RI bit in UiC1 register 1 0 IR bit in SiRIC register 1 0 D2 D3 D4 D5 Read out from UiRB register Set to 0 when interrupt request is acknowledged, or set by a program The above applies under the following settings: * CKDIR bit in UiMR register = 1 (external clock) * CKPOL bit in UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) The following conditions are met when "H" is applied to the CLKi pin before receiving data: * TE bit in UiC1 register = 1 (enables transmit) * RE bit in UiC1 register = 1 (enables receive) * Write dummy data to the UiTB register fEXT: Frequency of external clock i = 0 or 1 Figure 15.8 Transmit and Receive Timing Example in Clock Synchronous Serial I/O Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 250 of 453 R8C/26 Group, R8C/27 Group 15.1.1 15. Serial Interface Polarity Select Function Figure 15.9 shows the Transfer Clock Polarity. Use the CKPOL bit in the UiC0 (i = 0 or 1) register to select the transfer clock polarity. * When the CKPOL bit in the UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) CLKi(1) TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 * When the CKPOL bit in the UiC0 register = 1 (output transmit data at the rising edge and input receive data at the falling edge of the transfer clock) CLKi(2) TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 NOTES: 1. When not transferring, the CLKi pin level is "H". 2. When not transferring, the CLKi pin level is "L". i = 0 or 1 Figure 15.9 15.1.2 Transfer Clock Polarity LSB First/MSB First Select Function Figure 15.10 shows the Transfer Format. Use the UFORM bit in the UiC0 (i = 0 or 1) register to select the transfer format. * When UFORM bit in UiC0 register = 0 (LSB first)(1) CLKi TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 * When UFORM bit in UiC0 register = 1 (MSB first)(1) CLKi TXDi D7 D6 D5 D4 D3 D2 D1 D0 RXDi D7 D6 D5 D4 D3 D2 D1 D0 NOTE: 1. The above applies when the CKPOL bit in the UiC0 register is set to 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock). i = 0 or 1 Figure 15.10 Transfer Format Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 251 of 453 R8C/26 Group, R8C/27 Group 15.1.3 15. Serial Interface Continuous Receive Mode Continuous receive mode is selected by setting the UiRRM (i = 0 or 1) bit in the UiC1 register to 1 (enables continuous receive mode). In this mode, reading the UiRB register sets the TI bit in the UiC1 register to 0 (data in the UiTB register). When the UiRRM bit is set to 1, do not write dummy data to the UiTB register by a program. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 252 of 453 R8C/26 Group, R8C/27 Group 15.2 15. Serial Interface Clock Asynchronous Serial I/O (UART) Mode The UART mode allows data transmission and reception after setting the desired bit rate and transfer data format. Table 15.4 lists the Specifications of UART Mode. Table 15.5 lists the Registers Used and Settings for UART Mode. Table 15.4 Specifications of UART Mode Item Transfer data formats Transfer clocks Transmit start conditions Receive start conditions Interrupt request generation timing Error detection Specification * Character bit (transfer data): Selectable among 7, 8 or 9 bits * Start bit: 1 bit * Parity bit: Selectable among odd, even, or none * Stop bit: Selectable among 1 or 2 bits * CKDIR bit in UiMR register is set to 0 (internal clock): fj/(16(n+1)) fj = f1, f8, f32 n = value set in UiBRG register: 00h to FFh * CKDIR bit is set to 1 (external clock): fEXT/(16(n+1)) fEXT: Input from CLKi pin, n = value set in UiBRG register: 00h to FFh * Before transmission starts, the following are required - TE bit in UiC1 register is set to 1 (transmission enabled) - TI bit in UiC1 register is set to 0 (data in UiTB register) * Before reception starts, the following are required - RE bit in UiC1 register is set to 1 (reception enabled) - Start bit detected * When transmitting, one of the following conditions can be selected - UiIRS bit is set to 0 (transmit buffer empty): When transferring data from the UiTB register to UARTi transmit register (when transmit starts). - UiIRS bit is set to 1 (transfer ends): When serial interfac.e completes transmitting data from the UARTi transmit register * When receiving When transferring data from the UARTi receive register to UiRB register (when receive ends). * Overrun error(1) This error occurs if the serial interface starts receiving the next data item before reading the UiRB register and receive the bit preceding the final stop bit of the next data item. * Framing error This error occurs when the set number of stop bits is not detected. * Parity error This error occurs when parity is enabled, and the number of 1's in parity and character bits do not match the number of 1's set. * Error sum flag This flag is set is set to 1 when an overrun, framing, or parity error is generated. i = 0 or 1 NOTE: 1. If an overrun error occurs, the receive data (b0 to b8) of the UiRB register will be undefined. The IR bit in the SiRIC register remains unchanged. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 253 of 453 R8C/26 Group, R8C/27 Group Table 15.5 15. Serial Interface Registers Used and Settings for UART Mode Register UiTB 0 to 8 Set transmit data(1) UiRB 0 to 8 UiBRG UiMR OER, FER, PER, SUM 0 to 7 SMD2 to SMD0 Receive data can be read(1, 2) Error flag Set a bit rate Set to 100b when transfer data is 7 bits long. Set to 101b when transfer data is 8 bits long. Set to 110b when transfer data is 9 bits long. Select the internal clock or external clock Select the stop bit Select whether parity is included and whether odd or even Select the count source for the UiBRG register Transmit register empty flag Select TXDi pin output mode Set to 0 LSB first or MSB first can be selected when transfer data is 8 bits long. Set to 0 when transfer data is 7 or 9 bits long. Set to 1 to enable transmit Transmit buffer empty flag Set to 1 to enable receive Receive complete flag Select the factor of UARTi transmit interrupt Set to 0 UiC0 UiC1 Bit CKDIR STPS PRY, PRYE CLK0, CLK1 TXEPT NCH CKPOL UFORM TE TI RE RI UiIRS UiRRM Function i = 0 or 1 NOTES: 1. The bits used for transmit/receive data are as follows: Bits 0 to 6 when transfer data is 7 bits long; bits 0 to 7 when transfer data is 8 bits long; bits 0 to 8 when transfer data is 9 bits long. 2. The following bits are undefined: Bits 7 and 8 when transfer data is 7 bits long; bit 8 when transfer data is 8 bits long. Table 15.6 lists the I/O Pin Functions in UART Mode. After the UARTi (i = 0 or 1) operating mode is selected, the TXDi pin outputs "H" level (If the NCH bit is set to 1 (N-channel open-drain output), this pin is in a highimpedance state) until transfer starts. Table 15.6 I/O Pin Functions in UART Mode Pin name Function TXD0 (P1_4) Output serial data RXD0 (P1_5) Input serial data CLK0 (P1_6) Programmable I/O Port Input transfer clock TXD1 (either P0_0, P3_6, or P3_7) RXD1 (either P3_6, P3_7, or P4_5) Output serial data CLK1 (P0_5) Input serial data Programmable I/O Port Input transfer clock Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Selection Method (Cannot be used as a port when performing reception only) PD1_5 bit in PD1 register = 0 (P1_5 can be used as an input port when performing transmission only) CKDIR bit in U0MR register = 0 CKDIR bit in U0MR register = 1 PD1_6 bit in PD1 register = 0 Set registers PINSR1 and PMR (refer to Figure 15.7 Registers PINSR1 and PMR) (Cannot be used as a port when performing reception only) Set registers PINSR1 and PMR (refer to Figure 15.7 Registers PINSR1 and PMR) Corresponding bit in each port direction register = 0 (Can be used as an input port when performing transmission only) CKDIR bit in U1MR register = 0 PD0_5 bit in PD0 register = 0 CKDIR bit in U1MR register = 1 Page 254 of 453 R8C/26 Group, R8C/27 Group 15. Serial Interface * Transmit timing when transfer data is 8 bits long (parity enabled, 1 stop bit) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write data to UiTB register Transfer from UiTB register to UARTi transmit register Start bit TXDi ST TXEPT bit in UiC0 register 1 0 IR bit SiTIC register 1 0 Stop pulsing because the TE bit is set to 0 Parity Stop bit bit D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 Set to 0 when interrupt request is acknowledged, or set by a program TC=16 (n + 1) / fj or 16 (n + 1) / fEXT The above timing diagram applies under the following conditions: * PRYE bit in UiMR register = 1 (parity enabled) fj: Frequency of UiBRG count source (f1, f8, f32) * STPS bit in UiMR register = 0 (1 stop bit) fEXT: Frequency of UiBRG count source (external clock) * UiIRS bit in UiC1 register = 1 (an interrupt request is generated when transmit completes) n: Setting value to UiBRG register i = 0 or 1 * Transmit timing when transfer data is 9 bits long (parity disabled, 2 stop bits) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write data to UiTB register Transfer from UiTB register to UARTi transmit register Stop Stop bit bit Start bit TXDi ST TXEPT bit in UiC0 register 1 0 IR bit in SiTIC register 1 0 D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP ST D0 Set to 0 when interrupt request is acknowledged, or set by a program The above timing diagram applies under the following conditions: * PRYE bit in UiMR register = 0 (parity disabled) * STPS bit in UiMR register = 1 (2 stop bits) * UiIRS bit in UiC1 register = 0 (an interrupt request is generated when transmit buffer is empty) Figure 15.11 Transmit Timing in UART Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 255 of 453 TC=16 (n + 1) / fj or 16 (n + 1) / fEXT fj: Frequency of UiBRG count source (f1, f8, f32) fEXT: Frequency of UiBRG count source (external clock) n: Setting value to UiBRG register i = 0 or 1 D1 R8C/26 Group, R8C/27 Group 15. Serial Interface * Example of receive timing when transfer data is 8 bits long (parity disabled, one stop bit) UiBRG output UiC1 register RE bit 1 0 Stop bit Start bit RXDi D0 D1 D7 Determined to be "L" Receive data taken in Transfer clock Reception triggered when transfer clock is generated by falling edge of start bit UiC1 register RI bit 1 0 SiRIC register IR bit 1 0 Transferred from UARTi receive register to UiRB register Set to 0 when interrupt request is accepted, or set by a program The above timing diagram applies when the register bits are set as follows: * PRYE bit in UiMR register = 0 (parity disabled) * STPS bit in UiMR register = 0 (1 stop bit) i = 0 or 1 Figure 15.12 Receive Timing Example in UART Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 256 of 453 R8C/26 Group, R8C/27 Group 15.2.1 15. Serial Interface Bit Rate In UART mode, the bit rate is the frequency divided by the UiBRG (i = 0 or 1) register. UART mode * Internal clock selected UiBRG register setting value = fj Bit Rate x 16 -1 Fj: Count source frequency of the UiBRG register (f1, f8, or f32) * External clock selected UiBRG register setting value = fEXT Bit Rate x 16 -1 fEXT: Count source frequency of the UiBRG register (external clock) i = 0 or 1 Figure 15.13 Calculation Formula of UiBRG (i = 0 or 1) Register Setting Value Table 15.7 Bit Rate Setting Example in UART Mode (Internal Clock Selected) Bit Rate (bps) UiBRG Count Source 1200 2400 4800 9600 14400 19200 28800 38400 57600 115200 f8 f8 f8 f1 f1 f1 f1 f1 f1 f1 System Clock = 20 MHz System Clock = 18.432 MHz(1) Setting Setting UiBRG UiBRG Actual Time Actual Time Error Error Setting Setting (bps) (bps) (%) (%) Value Value 129 (81h) 1201.92 0.16 119 (77h) 1200.00 0.00 64 (40h) 2403.85 0.16 59 (3Bh) 2400.00 0.00 32 (20h) 4734.85 -1.36 29 (1Dh) 4800.00 0.00 129 (81h) 9615.38 0.16 119 (77h) 9600.00 0.00 86 (56h) 14367.82 -0.22 79 (4Fh) 14400.00 0.00 64 (40h) 19230.77 0.16 59 (3Bh) 19200.00 0.00 42 (2Ah) 29069.77 0.94 39 (27h) 28800.00 0.00 32 (20h) 37878.79 -1.36 29 (1Dh) 38400.00 0.00 21 (15h) 56818.18 -1.36 19 (13h) 57600.00 0.00 10 (0Ah) 113636.36 -1.36 9 (09h) 115200.00 0.00 System Clock = 8 MHz UiBRG Actual Setting Setting Time Error Value (bps) (%) 51 (33h) 1201.92 0.16 25 (19h) 2403.85 0.16 12 (0Ch) 4807.69 0.16 51 (33h) 9615.38 0.16 34 (22h) 14285.71 -0.79 25 (19h) 19230.77 0.16 16 (10h) 29411.76 2.12 12 (0Ch) 38461.54 0.16 8 (08h) 55555.56 -3.55 - - - i = 0 or 1 NOTE: 1. For the high-speed on-chip oscillator, the correction value in the FRA7 register should be written into the FRA1 register (for N, D version only). This applies when the high-speed on-chip oscillator is selected as the system clock and bits FRA22 to FRA20 in the FRA2 register are set to 000b (divide-by-2 mode). For the precision of the high-speed on-chip oscillator, refer to 20. Electrical Characteristics. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 257 of 453 R8C/26 Group, R8C/27 Group 15.3 15. Serial Interface Notes on Serial Interface * When reading data from the UiRB (i = 0 or 1) register either in the clock synchronous serial I/O mode or in the clock asynchronous serial I/O mode. Ensure the data is read in 16-bit units. When the high-order byte of the UiRB register is read, bits PER and FER in the UiRB register and the RI bit in the UiC1 register are set to 0. To check receive errors, read the UiRB register and then use the read data. Example (when reading receive buffer register): MOV.W 00A6H,R0 ; Read the U0RB register * When writing data to the UiTB register in the clock asynchronous serial I/O mode with 9-bit transfer data length, write data to the high-order byte first then the low-order byte, in 8-bit units. Example (when reading transmit buffer register): MOV.B #XXH,00A3H ; Write the high-order byte of U0TB register MOV.B #XXH,00A2H ; Write the low-order byte of U0TB register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 258 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface 16. Clock Synchronous Serial Interface The clock synchronous serial interface is configured as follows. Clock synchronous serial interface Clock synchronous serial I/O with chip select (SSU) Clock synchronous communication mode 4-wire bus communication mode I2C bus Interface I2C bus interface mode Clock synchronous serial mode The clock synchronous serial interface uses the registers at addresses 00B8h to 00BFh. Registers, bits, symbols, and functions vary even for the same addresses depending on the mode. Refer to the register diagrams of each function for details. Also, the differences between clock synchronous communication mode and clock synchronous serial mode are the options of the transfer clock, clock output format, and data output format. 16.1 Mode Selection The clock synchronous serial interface has four modes. Table 16.1lists the Mode Selections. Refer to 16.2 Clock Synchronous Serial I/O with Chip Select (SSU) and the sections that follow for details of each mode. Table 16.1 IICSEL Bit in PMR Register Mode Selections Bit 7 in 00B8h (ICE Bit in ICCR1 Register) Bit 0 in 00BDh (SSUMS Bit in Function SSMR2 Register, FS Bit in SAR Register) 0 Clock synchronous serial I/O with chip select 1 0 0 0 1 0 1 0 1 1 1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 259 of 453 I2C bus interface Mode Clock synchronous communication mode 4-wire bus communication mode I2C bus interface mode Clock synchronous serial mode R8C/26 Group, R8C/27 Group 16.2 16. Clock Synchronous Serial Interface Clock Synchronous Serial I/O with Chip Select (SSU) Clock synchronous serial I/O with chip select supports clock synchronous serial data communication. Table 16.2 lists the Specifications of Clock Synchronous Serial I/O with Chip Select and Figure 16.1 shows a Block Diagram of Clock Synchronous Serial I/O with Chip Select. Figures 16.2 to 16.9 show the registers associated with clock synchronous serial I/O with chip select. Table 16.2 Specifications of Clock Synchronous Serial I/O with Chip Select Item Transfer data format Operating modes Master/slave device I/O pins Transfer clocks Receive error detection Multimaster error detection Interrupt requests Select functions Specification * Transfer data length: 8 bits Continuous transmission and reception of serial data are supported since both transmitter and receiver have buffer structures. * Clock synchronous communication mode * 4-wire bus communication mode (including bidirectional communication) Selectable SSCK (I/O): Clock I/O pin SSI (I/O): Data I/O pin SSO (I/O): Data I/O pin SCS (I/O): Chip-select I/O pin * When the MSS bit in the SSCRH register is set to 0 (operates as slave device), external clock is selected (input from SSCK pin). * When the MSS bit in the SSCRH register is set to 1 (operates as master device), internal clock (selectable among f1/256, f1/128, f1/64, f1/32, f1/16, f1/8 and f1/4, output from SSCK pin) is selected. * Clock polarity and phase of SSCK can be selected. * Overrun error Overrun error occurs during reception and completes in error. While the RDRF bit in the SSSR register is set to 1 (data in the SSRDR register) and when next serial data receive is completed, the ORER bit is set to 1. * Conflict error When the SSUMS bit in the SSMR2 register is set to 1 (4-wire bus communication mode) and the MSS bit in the SSCRH register is set to 1 (operates as master device) and when starting a serial communication, the CE bit in the SSSR register is set to 1 if "L" applies to the SCS pin input. When the SSUMS bit in the SSMR2 register is set to 1 (4-wire bus communication mode), the MSS bit in the SSCRH register is set to 0 (operates as slave device) and the SCS pin input changes state from "L" to "H", the CE bit in the SSSR register is set to 1. 5 interrupt requests (transmit-end, transmit-data-empty, receive-data-full, overrun error, and conflict error).(1) * Data transfer direction Selects MSB-first or LSB-first * SSCK clock polarity Selects "L" or "H" level when clock stops * SSCK clock phase Selects edge of data change and data download * SSI pin select function The SSISEL bit in the PMR register can select P3_3 or P1_6 as SSI pin. NOTE: 1. Clock synchronous serial I/O with chip select has only one interrupt vector table. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 260 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface f1 Internal clock (f1/i) Internal clock generation circuit Multiplexer SSCK SSMR register SSCRL register SSCRH register Transmit/receive control circuit SCS SSER register SSMR2 register SSTDR register SSO Selector SSTRSR register SSI SSRDR register Interrupt requests (TXI, TEI, RXI, OEI, and CEI) i = 4, 8, 16, 32, 64, 128, or 256 Figure 16.1 Block Diagram of Clock Synchronous Serial I/O with Chip Select Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 261 of 453 Data bus SSSR register R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Control Register H b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSCRH Bit Symbol Address 00B8h Bit Name Transfer clock rate select bits (1) CKS1 CKS2 Nothing is assigned. If necessary, set to 0. When read, the content is 0. (2) MSS Master/slave device select bit (3) Receive single stop bit RSSTP -- (b7) RW b2 b1 b0 0 0 0 : f1/256 0 0 1 : f1/128 0 1 0 : f1/64 0 1 1 : f1/32 1 0 0 : f1/16 1 0 1 : f1/8 1 1 0 : f1/4 1 1 1 : Do not set. CKS0 -- (b4-b3) After Reset 00h Function RW RW RW -- 0 : Operates as slave device 1 : Operates as master device RW 0 : Maintains receive operation after receiving 1 byte of data 1 : Completes receive operation after receiving 1 byte of data RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. The set clock is used w hen the internal clock is selected. 2. The SSCK pin functions as the transfer clock output pin w hen the MSS bit is set to 1 (operates as master device). The MSS bit is set to 0 (operates as slave device) w hen the CE bit in the SSSR register is set to 1 (conflict error occurs). 3. The RSSTP bit is disabled w hen the MSS bit is set to 0 (operates as slave device). Figure 16.2 SSCRH Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 262 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Control Register L b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 00B9h SSCRL Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b0) When read, the content is 1. SRES -- (b3-b2) SOLP SOL Clock synchronous serial I/O w ith chip select control part reset bit After Reset 01111101b Function When this bit is set to 1, the clock synchronous serial I/O w ith chip select control block and SSTRSR register are reset. The values of the registers (1) in the clock synchronous serial I/O w ith chip select register are maintained. RW -- RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- SOL w rite protect bit(2) The output level can be changed by the SOL bit w hen this bit is set to 0. The SOLP bit remains unchanged even if 1 is w ritten to it. When read, the content is 1. RW Serial data output value When read setting bit 0 : The serial data output is set to "L" 1 : The serial data output is set to "H" When w ritten(2, 3) 0 : The data output is "L" after the serial data output 1 : The data output is "H" after the serial data output RW -- (b6) Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- -- (b7) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. Registers SSCRH, SSCRL, SSMR, SSER, SSSR, SSMR2, SSTDR, and SSRDR. 2. The data output after serial data is output can be changed by w riting to the SOL bit before or after transfer. When w riting to the SOL bit, set the SOLP bit to 0 and the SOL bit to 0 or 1 simultaneously by the MOV instruction. 3. Do not w rite to the SOL bit during data transfer. Figure 16.3 SSCRL Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 263 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Mode Register b7 b6 b5 b4 b3 b2 b1 b0 1 Symbol SSMR Bit Symbol Address 00BAh Bit Name Bits counter 2 to 0 After Reset 00011000b Function 0 0 0 : 8 bits left 0 0 1 : 1 bit left 0 1 0 : 2 bits left 0 1 1 : 3 bits left 1 0 0 : 4 bits left 1 0 1 : 5 bits left 1 1 0 : 6 bits left 1 1 1 : 7 bits left BC0 BC1 BC2 Set to 1. When read, the content is 1. -- (b3) Reserved bit -- (b4) Nothing is assigned. If necessary, set to 0. When read, the content is 1. (1) RO RO RW -- RW SSCK clock polarity select bit(1) 0 : "H" w hen clock stops 1 : "L" w hen clock stops RW MSB first/LSB first select bit 0 : Transfers data MSB first 1 : Transfers data LSB first RW CPHS MLS RO 0 : Change data at odd edge (Dow nload data at even edge) 1 : Change data at even edge (Dow nload data at odd edge) SSCK clock phase select bit CPOS RW b2 b1 b0 NOTE: 1. Refer to 16.2.1.1 Association betw een Transfer Clock Polarity, Phase, and Data for the settings of the CPHS and CPOS bits. Figure 16.4 SSMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 264 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSER Bit Symbol CEIE -- (b2-b1) RE TE Address After Reset 00BBh 00h Bit Name Function Conflict error interrupt enable bit 0 : Disables conflict error interrupt request 1 : Enables conflict error interrupt request RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Receive enable bit 0 : Disables receive 1 : Enables receive RW Transmit enable bit 0 : Disables transmit 1 : Enables transmit RW Receive interrupt enable bit 0 : Disables receive data full and overrun error interrupt request 1 : Enables receive data full and overrun error interrupt request RW RIE TEIE Transmit end interrupt enable bit 0 : Disables transmit end interrupt request 1 : Enables transmit end interrupt request Transmit interrupt enable bit TIE Figure 16.5 SSER Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW Page 265 of 453 0 : Disables transmit data empty interrupt request 1 : Enables transmit data empty interrupt request RW RW R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Status Register(7) b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSSR Bit Symbol CE -- (b1) Address 00BCh Bit Name Conflict error flag(1) Nothing is assigned. If necessary, set to 0. When read, the content is 0. (1) ORER -- (b4-b3) RDRF After Reset 00h Function 0 : No conflict errors generated 1 : Conflict errors generated(2) Overrun error flag 0 : No overrun errors generated 1 : Overrun errors generated(3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. Receive data register full (1,4) (1, 5) Transmit end TEND Transmit data empty (1, 5, 6) TDRE RW RW -- RW -- 0 : No data in SSRDR register 1 : Data in SSRDR register RW 0 : The TDRE bit is set to 0 w hen transmitting the last bit of transmit data 1 : The TDRE bit is set to 1 w hen transmitting the last bit of transmit data RW 0 : Data is not transferred from registers SSTDR to SSTRSR 1 : Data is transferred from registers SSTDR to SSTRSR RW NOTES: 1. Writing 1 to CE, ORER, RDRF, TEND, or TDRE bits invalid. To set any of these bits to 0, first read 1 then w rite 0. 2. When the serial communication is started w hile the SSUMS bit in the SSMR2 register is set to 1 (four-w ire bus communication mode) and_____ the MSS bit in the SSCRH register is set to 1 (operates as master device), the CE bit is set _____ to 1 if "L" is applied to the SCS pin input. Refer to 16.2.7 SCS Pin Control and Arbitration for m ore inform ation. When the SSUMS bit in the SSMR2 register is set to 1 (four-w ire bus communication mode), the MSS bit in the _____ SSCRH register is set to 0 (operates as slave device) and the SCS pin input changes the level from "L" to "H" during transfer, the CE bit is set to 1. 3. Indicates w hen overrun errors occur and receive completes by error reception. If the next serial data receive operation is completed w hile the RDRF bit is set to 1 (data in the SSRDR register), the ORER bit is set to 1. After the ORER bit is set to 1 (overrun error), transmit and receive operations are disabled w hile the bit remains 1. 4. 5. 6. 7. The RDRF bit is set to 0 w hen reading out the data from the SSRDR register. Bits TEND and TDRE are set to 0 w hen w riting data to the SSTDR register. The TDRE bit is set to 1 w hen the TE bit in the SSER register is set to 1 (transmit enabled). When accessing the SSSR register continuously, insert one or more NOP instructions betw een the instructions to access it. Figure 16.6 SSSR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 266 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Mode Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSMR2 Bit Symbol SSUMS Address After Reset 00BDh 00h Bit Name Function Clock synchronous serial I/O w ith 0 : Clock synchronous communication mode 1 : Four-w ire bus communication mode chip select mode select bit(1) _____ CSOS SOOS SCKOS SCS pin open drain output select bit Serial data pin open output drain select bit(1) 0 : CMOS output 1 : N-channel open drain output 0 : CMOS output(5) 1 : N-channel open drain output SSCK pin open drain output select bit 0 : CMOS output 1 : N-channel open drain output RW RW RW RW RW _____ SCS pin select bits (2) b5 b4 0 0 : Functions 0 1 : Functions 1 0 : Functions 1 1 : Functions CSS0 CSS1 SCKS SSCK pin select bit (1, 4) Bidirectional mode enable bit BIDE as as as as port SCS input pin _____ SCS output pin(3) _____ SCS output pin(3) _____ RW RW 0 : Functions as port 1 : Functions as serial clock pin RW 0 : Standard mode (communication using 2 pins of data input and data output) 1 : Bidirectional mode (communication using 1 pin of data input and data output) RW NOTES: 1. Refer to 16.2.2.1 Association betw een Data I/O Pins and SS Shift Register for information on combinations of data I/O pins. _____ 2. The SCS pin functions as a port, regardless of the values of bits CSS0 and CSS1 w hen the SSUMS bit is set to 0 (clock synchronous communication mode). _____ 3. This bit functions as the SCS input pin before starting transfer. 4. The BIDE bit is disabled w hen the SSUMS bit is set to 0 (clock synchronous communication mode). 5. The SSI pin and SSO pin corresponding port direction bits are set to 0 (input mode) w hen the SOOS bit is set to 0 (CMOS output). Figure 16.7 SSMR2 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 267 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SS Transmit Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSTDR Address 00BEh After Reset FFh Function RW Store the transmit data. The stored transmit data is transferred to the SSTRSR register and transmission is started w hen it is detected that the SSTRSR register is empty. When the next transmit data is w ritten to the SSTDR register during the data transmission from RW the SSTRSR register, the data can be transmitted continuously. When the MLS bit in the SSMR register is set to 1 (transfer data w ith LSB-first), the data in w hich MSB and LSB are reversed is read, after w riting to the SSTDR register. SS Receive Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol SSRDR Address 00BFh After Reset FFh Function Store the receive data.(1) The receive data is transferred to the SSRDR register and the receive operation is completed w hen 1 byte of data has been received by the SSTRSR register. At this time, the next receive operation is possible. Continuous reception is possible using registers SSTRSR and SSRDR. RW RO NOTE: 1. The SSRDR register retains the data reception before an overrun error occurs (ORER bit in the SSSR register set to 1 (overrun error)). When an overrun error occurs, the receive data may contain errors and therefore should be discarded. Figure 16.8 Registers SSTDR and SSRDR Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 268 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Port Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol PMR Bit Symbol INT1SEL -- (b2-b1) SSISEL U1PINSEL TXD1SEL TXD1EN IICSEL Address 00F8h Bit Name _____ INT1 pin select bit After Reset 00h Function 0 : P1_5, P1_7 1 : P3_6 Nothing is assigned. If necessary, set to 0. When read, the content is 0. SSI pin select bit 0 : P3_3 1 : P1_6 RW TXD1 pin sw itch bit(1) 0 : P0_0 1 : P3_6, P3_7 RW Port/TXD1 pin sw itch bit(1) 0 : Programmable I/O port 1 : TXD1 RW TXD1/RXD1 select bit(1) 0 : RXD1 1 : TXD1 RW SSU / I2C bus pin sw itch bit 0 : Selects SSU function 1 : Selects I2C bus function RW Pin Function U1PINSEL bit PMR Register TXD1SEL bit x x 0 1 P3_7(TXD1) 00b P3_7(RXD1) P0_0(TXD1) 01b P3_7(TXD1) P4_5(RXD1) P3_6(TXD1) 10b P3_6(RXD1) P0_0(TXD1) x: 0 or 1 Figure 16.9 PMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW -- NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN, and bits UART1SEL1 and UART1SEL0 in the PINSR1 register. PINSR1 Register UART1SEL1, UART1SEL0 bit RW Page 269 of 453 1 1 x x x 0 1 TXD1EN bit 1 0 x x 1 0 x R8C/26 Group, R8C/27 Group 16.2.1 16. Clock Synchronous Serial Interface Transfer Clock The transfer clock can be selected from among seven internal clocks (f1/256, f1/128, f1/64, f1/32, f1/16, f1/8, and f1/4) and an external clock. When using clock synchronous serial I/O with chip select, set the SCKS bit in the SSMR2 register to 1 and select the SSCK pin as the serial clock pin. When the MSS bit in the SSCRH register is set to 1 (operates as master device), an internal clock can be selected and the SSCK pin functions as output. When transfer is started, the SSCK pin outputs clocks of the transfer rate selected by bits CKS0 to CKS2 in the SSCRH register. When the MSS bit in the SSCRH register is set to 0 (operates as slave device), an external clock can be selected and the SSCK pin functions as input. 16.2.1.1 Association between Transfer Clock Polarity, Phase, and Data The association between the transfer clock polarity, phase and data changes according to the combination of the SSUMS bit in the SSMR2 register and bits CPHS and CPOS in the SSMR register. Figure 16.10 shows the Association between Transfer Clock Polarity, Phase, and Transfer Data. Also, the MSB-first transfer or LSB-first transfer can be selected by setting the MLS bit in the SSMR register. When the MLS bit is set to 1, transfer is started from the LSB and proceeds to the MSB. When the MLS bit is set to 0, transfer is started from the MSB and proceeds to the LSB. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 270 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface * SSUMS = 0 (clock synchronous communication mode), CPHS bit = 0 (data change at odd edge), and CPOS bit = 0 ("H" when clock stops) SSCK b0 SSO, SSI b1 b2 b3 b4 b5 b6 b7 * SSUMS = 1 (4-wire bus communication mode) and CPHS = 0 (data change at odd edge) SSCK CPOS = 0 ("H" when clock stops) SSCK CPOS = 1 ("L" when clock stops) SSO, SSI b0 b1 b2 b3 b4 b5 b6 b7 SCS * SSUMS = 1 (4-wire bus communication mode) and CPHS = 1 (data download at odd edge) SSCK CPOS = 0 ("H" when clock stops) SSCK CPOS = 1 ("L" when clock stops) SSO, SSI b0 b1 b2 b3 b4 b5 b6 b7 SCS CPHS and CPOS: Bits in SSMR register, SSUMS: Bits in SSMR2 register Figure 16.10 Association between Transfer Clock Polarity, Phase, and Transfer Data Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 271 of 453 R8C/26 Group, R8C/27 Group 16.2.2 16. Clock Synchronous Serial Interface SS Shift Register (SSTRSR) The SSTRSR register is a shift register for transmitting and receiving serial data. When transmit data is transferred from the SSTDR register to the SSTRSR register and the MLS bit in the SSMR register is set to 0 (MSB-first), the bit 0 in the SSTDR register is transferred to bit 0 in the SSTRSR register. When the MLS bit is set to 1 (LSB-first), bit 7 in the SSTDR register is transferred to bit 0 in the SSTRSR register. 16.2.2.1 Association between Data I/O Pins and SS Shift Register The connection between the data I/O pins and SSTRSR register (SS shift register) changes according to a combination of the MSS bit in the SSCRH register and the SSUMS bit in the SSMR2 register. The connection also changes according to the BIDE bit in the SSMR2 register. Figure 16.11 shows the Association between Data I/O Pins and SSTRSR Register. * SSUMS = 1 (4-wire bus communication mode), BIDE = 0 (standard mode), and MSS = 1 (operates as master device) * SSUMS = 0 (clock synchronous communication mode) SSTRSR register SSO SSTRSR register SSI * SSUMS = 1 (4-wire bus communication mode), BIDE = 0 (standard mode), and MSS = 0 (operates as slave device) SSTRSR register SSO SSI * SSUMS = 1 (4-wire bus communication mode) and BIDE = 1 (bidirectional mode) SSTRSR register SSI Figure 16.11 Association between Data I/O Pins and SSTRSR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 272 of 453 SSO SSO SSI R8C/26 Group, R8C/27 Group 16.2.3 16. Clock Synchronous Serial Interface Interrupt Requests Clock synchronous serial I/O with chip select has five interrupt requests: transmit data empty, transmit end, receive data full, overrun error, and conflict error. Since these interrupt requests are assigned to the clock synchronous serial I/O with chip select interrupt vector table, determining interrupt sources by flags is required. Table 16.3 shows the Clock Synchronous Serial I/O with Chip Select Interrupt Requests. Table 16.3 Clock Synchronous Serial I/O with Chip Select Interrupt Requests Interrupt Request Transmit data empty Transmit end Receive data full Overrun error Conflict error Abbreviation TXI TEI RXI OEI CEI Generation Condition TIE = 1, TDRE = 1 TEIE = 1, TEND = 1 RIE = 1, RDRF = 1 RIE = 1, ORER = 1 CEIE = 1, CE = 1 CEIE, RIE, TEIE and TIE: Bits in SSER register ORER, RDRF, TEND and TDRE: Bits in SSSR register If the generation conditions in Table 16.3 are met, a clock synchronous serial I/O with chip select interrupt request is generated. Set each interrupt source to 0 by a clock synchronous serial I/O with chip select interrupt routine. However, the TDRE and TEND bits are automatically set to 0 by writing transmit data to the SSTDR register and the RDRF bit is automatically set to 0 by reading the SSRDR register. In particular, the TDRE bit is set to 1 (data transmitted from registers SSTDR to SSTRSR) at the same time transmit data is written to the SSTDR register. Setting the TDRE bit to 0 (data not transmitted from registers SSTDR to SSTRSR) can cause an additional byte of data to be transmitted. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 273 of 453 R8C/26 Group, R8C/27 Group 16.2.4 16. Clock Synchronous Serial Interface Communication Modes and Pin Functions Clock synchronous serial I/O with chip select switches the functions of the I/O pins in each communication mode according to the setting of the MSS bit in the SSCRH register and bits RE and TE in the SSER register. Table 16.4 shows the Association between Communication Modes and I/O Pins. Table 16.4 Association between Communication Modes and I/O Pins Communication Mode Clock synchronous communication mode Bit Setting SSUMS BIDE MSS TE 0 Disabled 0 0 1 4-wire bus communication mode 1 0 0 1 4-wire bus 1 (bidirectional) communication mode(2) 1 0 1 RE 1 SSI Input -(1) Input Input 1 0 0 1 1 1 0 0 1 1 1 0 Output 0 1 1 Output Input 1 0 0 1 1 -(1) Input 1 -(1) Input -(1) Pin State SSO -(1) Output Output Page 274 of 453 Input -(1) Input Output Output Output Output Input Output Input -(1) Input Input -(1) Input Output Output Output -(1) Output Input Output Input 0 -(1) Output Input 0 1 -(1) Input Output 1 0 -(1) Output Output NOTES: 1. This pin can be used as a programmable I/O port. 2. Do not set both bits TE and RE to 1 in 4-wire bus (bidirectional) communication mode. SSUMS and BIDE: Bits in SSMR2 register MSS: Bit in SSCRH register TE and RE: Bits in SSER register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 SSCK Input R8C/26 Group, R8C/27 Group 16.2.5 16. Clock Synchronous Serial Interface Clock Synchronous Communication Mode 16.2.5.1 Initialization in Clock Synchronous Communication Mode Figure 16.12 shows the Initialization in Clock Synchronous Communication Mode. To initialize, set the TE bit in the SSER register to 0 (transmit disabled) and the RE bit to 0 (receive disabled) before data transmission or reception. Set the TE bit to 0 and the RE bit to 0 before changing the communication mode or format. Setting the RE bit to 0 does not change the contents of flags RDRF and ORER or the contents of the SSRDR register. Start RE bit 0 TE bit 0 SSER register SSUMS bit 0 SSMR2 register SSMR register CPHS bit 0 CPOS bit 0 Set MLS bit SSCRH register SCKS bit 1 Set SOOS bit SSMR2 register SSCRH register Set bits CKS0 to CKS2 Set RSSTP bit SSSR register SSER register Set MSS bit ORER bit 0(1) RE bit 1 (receive) TE bit 1 (transmit) Set bits RIE, TEIE, and TIE End NOTE: 1. Write 0 after reading 1 to set the ORER bit to 0. Figure 16.12 Initialization in Clock Synchronous Communication Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 275 of 453 R8C/26 Group, R8C/27 Group 16.2.5.2 16. Clock Synchronous Serial Interface Data Transmission Figure 16.13 shows an Example of Clock Synchronous Serial I/O with Chip Select Operation for Data Transmission (Clock Synchronous Communication Mode). During data transmission, the clock synchronous serial I/O with chip select operates as described below. When clock synchronous serial I/O with chip select is set as a master device, it outputs a synchronous clock and data. When clock synchronous serial I/O with chip select is set as a slave device, it outputs data synchronized with the input clock. When the TE bit is set to 1 (transmit enabled) before writing the transmit data to the SSTDR register, the TDRE bit is automatically set to 0 (data not transferred from registers SSTDR to SSTRSR) and the data is transferred from registers SSTDR to SSTRSR. After the TDRE bit is set to 1 (data transferred from registers SSTDR to SSTRSR), transmission starts. When the TIE bit in the SSER register is set to 1, the TXI interrupt request is generated. When one frame of data is transferred while the TDRE bit is set to 0, data is transferred from registers SSTDR to SSTRSR and transmission of the next frame is started. If the 8th bit is transmitted while the TDRE bit is set to 1, the TEND bit in the SSSR register is set to 1 (the TDRE bit is set to 1 when the last bit of the transmit data is transmitted) and the state is retained. The TEI interrupt request is generated when the TEIE bit in the SSER register is set to 1 (transmit-end interrupt request enabled). The SSCK pin is fixed "H" after transmit-end. Transmit cannot be performed while the ORER bit in the SSSR register is set to 1 (overrun error). Confirm that the ORER bit is set to 0 before transmission. Figure 16.14 shows a Sample Flowchart of Data Transmission (Clock Synchronous Communication Mode). * SSUMS = 0 (clock synchronous communication mode), CPHS = 0 (data change at odd numbers), and CPOS = 0 ("H" when clock stops) SSCK SSO b0 b1 b7 1 frame TDRE bit in SSSR register 1 TEND bit in SSSR register 1 b1 b7 1 frame TEI interrupt request generation 0 TXI interrupt request generation 0 Processing by program Figure 16.13 b0 Write data to SSTDR register Example of Clock Synchronous Serial I/O with Chip Select Operation for Data Transmission (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 276 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Start Initialization (1) Read TDRE bit in SSSR register TDRE = 1 ? No (1) After reading the SSSR register and confirming that the TDRE bit is set to 1, write the transmit data to the SSTDR register. When the transmit data is written to the SSTDR register, the TDRE bit is automatically set to 0. Yes Write transmit data to SSTDR register Data transmission continues? (2) Yes (2) Determine whether data transmission continues. No (3) Read TEND bit in SSSR register TEND = 1 ? (3) When data transmission is completed, the TEND bit is set to 1. Set the TEND bit to 0 and the TE bit to 0 and complete transmit mode. No Yes SSSR register TEND bit 0(1) SSER register TE bit 0 End NOTE: 1. Write 0 after reading 1 to set the TEND bit to 0. Figure 16.14 Sample Flowchart of Data Transmission (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 277 of 453 R8C/26 Group, R8C/27 Group 16.2.5.3 16. Clock Synchronous Serial Interface Data Reception Figure 16.15 shows an Example of Clock Synchronous Serial I/O with Chip Select Operation for Data Reception (Clock Synchronous Communication Mode). During data reception, clock synchronous serial I/O with chip select operates as described below. When the clock synchronous serial I/O with chip select is set as the master device, it outputs a synchronous clock and inputs data. When the clock synchronous serial I/O with chip select is set as a slave device, it inputs data synchronized with the input clock. When clock synchronous serial I/O with chip select is set as a master device, it outputs a receive clock and starts receiving by performing dummy read of the SSRDR register. After 8 bits of data are received, the RDRF bit in the SSSR register is set to 1 (data in the SSRDR register) and receive data is stored in the SSRDR register. When the RIE bit in the SSER register is set to 1 (RXI and OEI interrupt requests enabled), the RXI interrupt request is generated. If the SSDR register is read, the RDRF bit is automatically set to 0 (no data in the SSRDR register). Read the receive data after setting the RSSTP bit in the SSCRH register to 1 (after receiving 1 byte of data, the receive operation is completed). Clock synchronous serial I/O with chip select outputs a clock for receiving 8 bits of data and stops. After that, set the RE bit in the SSER register to 0 (receive disabled) and the RSSTP bit to 0 (receive operation is continued after receiving the 1 byte of data) and read the receive data. If the SSRDR register is read while the RE bit is set to 1 (receive enabled), a receive clock is output again. When the 8th clock rises while the RDRF bit is set to 1, the ORER bit in the SSSR register is set to 1 (overrun error: OEI) and the operation is stopped. When the ORER bit is set to 1, receive cannot be performed. Confirm that the ORER bit is set to 0 before restarting receive. Figure 16.16 shows a Sample Flowchart for Data Reception (MSS = 1) (Clock Synchronous Communication Mode). * SSUMS = 0 (clock synchronous communication mode), CPHS = 0 (data download at even edges), and CPOS bit = 0 ("H" when clock stops) SSCK b7 b0 SSI b0 b7 1 RSSTP bit in SSCRH register 1 Processing by program Figure 16.15 b7 1 frame 1 frame RDRF bit in SSSR register b0 0 RXI interrupt request generation RXI interrupt request generation RXI interrupt request generation 0 Dummy read in SSRDR register Read data in SSRDR register Set RSSTP bit to 1 Read data in SSRDR register Example of Clock Synchronous Serial I/O with Chip Select Operation for Data Reception (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 278 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Start Initialization (1) Dummy read of SSRDR register (2) Last data received? Yes (1) After setting each register in the clock synchronous serial I/O with chip select register, a dummy read of the SSRDR register is performed and the receive operation is started. (2) Determine whether it is the last 1 byte of data to be received. If so, set to stop after the data is received. No Read ORER bit in SSSR register Yes (3) If a receive error occurs, perform error (6) Processing after reading the ORER bit. Then set the ORER bit to 0. Transmission/reception cannot be restarted while the ORER bit is set to 1. ORER = 1 ? (3) No Read RDRF bit in SSSR register (4) No (4) Confirm that the RDRF bit is set to 1. If the RDRF bit is set to 1, read the receive data in the SSRDR register. When the SSRDR register is read, the RDRF bit is automatically set to 0. RDRF = 1 ? Yes Read receive data in SSRDR register (5) SSCRH register RSSTP bit 1 (5) Before the last 1 byte of data is received, set the RSSTP bit to 1 and stop after the data is received. Read ORER bit in SSSR register ORER = 1 ? (6) Yes No Read RDRF in SSSR register No RDRF = 1 ? (7) Yes SSCRH register RSSTP bit 0 SSER register RE bit 0 (7) Confirm that the RDRF bit is set to 1. When the receive operation is completed, set the RSSTP bit to 0 and the RE bit to 0 before reading the last 1 byte of data. If the SSRDR register is read before setting the RE bit to 0, the receive operation is restarted again. Overrun error processing Read receive data in SSRDR register End Figure 16.16 Sample Flowchart for Data Reception (MSS = 1) (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 279 of 453 R8C/26 Group, R8C/27 Group 16.2.5.4 16. Clock Synchronous Serial Interface Data Transmission/Reception Data transmission/reception is an operation combining data transmission and reception which were described earlier. Transmission/reception is started by writing data to the SSTDR register. When the 8th clock rises or the ORER bit is set to 1 (overrun error) while the TDRE bit is set to 1 (data is transferred from registers SSTDR to SSTRSR), the transmit/receive operation is stopped. When switching from transmit mode (TE = 1) or receive mode (RE = 1) to transmit/receive mode (Te = RE = 1), set the TE bit to 0 and RE bit to 0 before switching. After confirming that the TEND bit is set to 0 (the TDRE bit is set to 0 when the last bit of the transmit data is transmitted), the RDRF bit is set to 0 (no data in the SSRDR register), and the ORER bit is set to 0 (no overrun error), set bits TE and RE to 1. Figure 16.17 shows a Sample Flowchart for Data Transmission/Reception (Clock Synchronous Communication Mode). When exiting transmit/receive mode after this mode is used (TE = RE = 1), a clock may be output if transmit/receive mode is exited after reading the SSRDR register. To avoid any clock outputs, perform either of the following: - First set the RE bit to 0, and then set the TE bit to 0. - Set bits TE and RE at the same time. When subsequently switching to receive mode (TE = 0 and RE = 1), first set the SRES bit to 1, and set this bit to 0 to reset the clock synchronous serial interface control unit and the SSTRSR register. Then, set the RE bit to 1. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 280 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Start Initialization (1) Read TDRE bit in SSSR register TDRE = 1 ? No (1) After reading the SSSR register and confirming that the TDRE bit is set to 1, write the transmit data to the SSTDR register. When the transmit data is written to the SSTDR register, the TDRE bit is automatically set to 0. Yes Write transmit data to SSTDR register (2) Read RDRF bit in SSSR register No RDRF = 1 ? (2) Confirm that the RDRF bit is set to 1. If the RDRF bit is set to 1, read the receive data in the SSRDR register. When reading the SSRDR register is read, the RDRF bit is automatically set to 0. Yes Read receive data in SSRDR register Data transmission continues? (3) Yes (3) Determine whether the data transmission continues No (4) Read TEND bit in SSSR register TEND = 1 ? (4) When the data transmission is completed, the TEND bit in the SSSR register is set to 1. No Yes (5) (6) SSSR register TEND bit 0(1) SSER register RE bit 0 TE bit 0 (5) Set the TEND bit to 0 and bits RE and TE in (6) the SSER register to 0 before ending transmit/ receive mode. End NOTE: 1. Write 0 after reading 1 to set the TEND bit to 0. Figure 16.17 Sample Flowchart for Data Transmission/Reception (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 281 of 453 R8C/26 Group, R8C/27 Group 16.2.6 16. Clock Synchronous Serial Interface Operation in 4-Wire Bus Communication Mode In 4-wire bus communication mode, a 4-wire bus consisting of a clock line, a data input line, a data output line, and a chip select line is used for communication. This mode includes bidirectional mode in which the data input line and data output line function as a single pin. The data input line and output line change according to the settings of the MSS bit in the SSCRH register and the BIDE bit in the SSMR2 register. For details, refer to 16.2.2.1 Association between Data I/O Pins and SS Shift Register. In this mode, clock polarity, phase, and data settings are performed by the CPOS and CPHS bits in the SSMR register. For details, refer to 16.2.1.1 Association between Transfer Clock Polarity, Phase, and Data. When this MCU is set as the master device, the chip select line controls output. When the clock synchronous serial I/O with chip select is set as a slave device, the chip select line controls input. When it is set as master device, the chip select line controls output of the SCS pin or controls output of a general port according to the setting of the CSS1 bit in the SSMR2 register. When the MCU is set as a slave device, the chip select line sets the SCS pin as an input pin by setting bits CSS1 and CSS0 in the SSMR2 register to 01b. In 4-wire bus communication mode, the MLS bit in the SSMR register is set to 0 and communication is performed MSB-first. 16.2.6.1 Initialization in 4-Wire Bus Communication Mode Figure 16.18 shows the Initialization in 4-Wire Bus Communication Mode. Before the data transit/receive operation, set the TE bit in the SSER register to 0 (transmit disabled), the RE bit in the SSER register to 0 (receive disabled), and initialize the clock synchronous serial I/O with chip select. To change the communication mode or format, set the TE bit to 0 and the RE bit to 0 before making the change. Setting the RE bit to 0 does not change the settings of flags RDRF and ORER or the contents of the SSRDR register. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 282 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Start RE bit 0 TE bit 0 SSER register SSUMS bit 1 SSMR2 register (1) SSMR register Set bits CPHS and CPOS MLS bits 0 SSCRH register SSMR2 register (2) SSCRH register Set MSS bit SCKS bit 1 Set bits SOOS, CSS0 to CSS1, and BIDE (2) Set the BIDE bit to 1 in bidirectional mode and set the I/O of the SCS pin by bits CSS0 and CSS1. Set bits CKS0 to CKS2 Set RSSTP bit ORER bit 0(1) SSSR register SSER register (1) The MLS bit is set to 0 for MSB-first transfer. The clock polarity and phase are set by bits CPHS and CPOS. RE bit 1 (receive) TE bit 1 (transmit) Set bits RIE, TEIE, and TIE End NOTE: 1. Write 0 after reading 1 to set the ORER bit to 0. Figure 16.18 Initialization in 4-Wire Bus Communication Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 283 of 453 R8C/26 Group, R8C/27 Group 16.2.6.2 16. Clock Synchronous Serial Interface Data Transmission Figure 16.19 shows an Example of Clock Synchronous Serial I/O with Chip Select Operation during Data Transmission (4-Wire Bus Communication Mode). During the data transmit operation, the clock synchronous serial I/O with chip select operates as described below. When the MCU is set as the master device, it outputs a synchronous clock and data. When the MCU is set as a slave device, it outputs data in synchronization with the input clock while the SCS pin is "L". When the transmit data is written to the SSTDR register after setting the TE bit to 1 (transmit enabled), the TDRE bit is automatically set to 0 (data has not been transferred from the SSTDR to the SSTRSR register) and the data is transferred from registers SSTDR to SSTRSR. After the TDRE bit is set to 1 (data is transferred from registers SSTDR to SSTRSR), transmission starts. When the TIE bit in the SSER register is set to 1, a TXI interrupt request is generated. After 1 frame of data is transferred while the TDRE bit is set to 0, the data is transferred from registers SSTDR to SSTRSR and transmission of the next frame is started. If the 8th bit is transmitted while TDRE is set to 1, TEND in the SSSR register is set to 1 (when the last bit of the transmit data is transmitted, the TDRE bit is set to 1) and the state is retained. If the TEIE bit in the SSER register is set to 1 (transmit-end interrupt requests enabled), a TEI interrupt request is generated. The SSCK pin remains "H" after transmit-end and the SCS pin is held "H". When transmitting continuously while the SCS pin is held "L", write the next transmit data to the SSTDR register before transmitting the 8th bit. Transmission cannot be performed while the ORER bit in the SSSR register is set to 1 (overrun error). Confirm that the ORER bit is set to 0 before transmission. In contrast to the clock synchronous communication mode, the SSO pin is placed in high-impedance state while the SCS pin is placed in high-impedance state when operating as a master device and the SSI pin is placed in high-impedance state while the SCS pin is placed in "H" input state when operating as a slave device. The sample flowchart is the same as that for the clock synchronous communication mode (refer to Figure 16.14 Sample Flowchart of Data Transmission (Clock Synchronous Communication Mode)). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 284 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface * CPHS bit = 0 (data change at odd edges) and CPOS bit = 0 ("H" when clock stops) High-impedance SCS (output) SSCK SSO b6 b7 b7 b0 b6 1 frame TDRE bit in SSSR register 1 TEND bit in SSSR register 1 b0 1 frame TEI interrupt request is generated 0 TXI interrupt request is generated TXI interrupt request is generated 0 Data write to SSTDR register Processing by program * CPHS bit = 1 (data change at even edges) and CPOS bit = 0 ("H" when clock stops) High-impedance SCS (output) SSCK b7 SSO b6 1 frame TDRE bit in SSSR register 1 TEND bit in SSSR register 1 b0 b7 b6 b0 1 frame TEI interrupt request is generated 0 TXI interrupt request is generated TXI interrupt request is generated 0 Processing by program Data write to SSTDR register CPHS, CPOS: Bits in SSMR register Figure 16.19 Example of Clock Synchronous Serial I/O with Chip Select Operation during Data Transmission (4-Wire Bus Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 285 of 453 R8C/26 Group, R8C/27 Group 16.2.6.3 16. Clock Synchronous Serial Interface Data Reception Figure 16.20 shows an Example of Clock Synchronous Serial I/O with Chip Select Operation during Data Reception (4-Wire Bus Communication Mode). During data reception, clock synchronous serial I/O with chip select operates as described below. When the MCU is set as the master device, it outputs a synchronous clock and inputs data. When the MCU is set as a slave device, it outputs data synchronized with the input clock while the SCS pin receives "L" input. When the MCU is set as the master device, it outputs a receive clock and starts receiving by performing a dummy read of the SSRDR register. After the 8 bits of data are received, the RDRF bit in the SSSR register is set to 1 (data in the SSRDR register) and receive data is stored in the SSRDR register. When the RIE bit in the SSER register is set to 1 (RXI and OEI interrupt requests enabled), an RXI interrupt request is generated. When the SSRDR register is read, the RDRF bit is automatically set to 0 (no data in the SSRDR register). Read the receive data after setting the RSSTP bit in the SSCRH register to 1 (after receiving 1-byte data, the receive operation is completed). Clock synchronous serial I/O with chip select outputs a clock for receiving 8 bits of data and stops. After that, set the RE bit in the SSER register to 0 (receive disabled) and the RSSTP bit to 0 (receive operation is continued after receiving 1-byte data) and read the receive data. When the SSRDR register is read while the RE bit is set to 1 (receive enabled), a receive clock is output again. When the 8th clock rises while the RDRF bit is set to 1, the ORER bit in the SSSR register is set to 1 (overrun error: OEI) and the operation is stopped. When the ORER bit is set to 1, reception cannot be performed. Confirm that the ORER bit is set to 0 before restarting reception. The timing with which bits RDRF and ORER are set to 1 varies depending on the setting of the CPHS bit in the SSMR register. Figure 16.20 shows when bits RDRF and ORER are set to 1. When the CPHS bit is set to 1 (data download at the odd edges), bits RDRF and ORER are set to 1 at some point during the frame. The sample flowchart is the same as that for the clock synchronous communication mode (refer to Figure 16.16 Sample Flowchart for Data Reception (MSS = 1) (Clock Synchronous Communication Mode)). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 286 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface * CPHS bit = 0 (data download at even edges) and CPOS bit = 0 ("H" when clock stops) High-impedance SCS (output) SSCK SSI b0 b7 b7 1 frame RDRF bit in SSSR register 1 RSSTP bit in SSCRH register 1 b7 b0 b0 1 frame 0 RXI interrupt request is generated RXI interrupt request is generated 0 Data read in SSRDR register Dummy read in SSRDR register Processing by program Set RSSTP bit to 1 RXI interrupt request is generated Data read in SSRDR register * CPHS bit = 1 (data download at odd edges) and CPOS bit = 0 ("H" when clock stops) High-impedance SCS (output) SSCK b7 SSI b0 b7 1 frame RDRF bit in SSSR register 1 RSSTP bit in SSCRH register 1 Processing by program b0 b7 b0 1 frame 0 RXI interrupt request is generated RXI interrupt request is generated 0 Dummy read in SSRDR register Data read in SSRDR register Set RSSTP bit to 1 RXI interrupt request is generated Data read in SSRDR register CPHS and CPOS: Bit in SSMR register Figure 16.20 Example of Clock Synchronous Serial I/O with Chip Select Operation during Data Reception (4-Wire Bus Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 287 of 453 R8C/26 Group, R8C/27 Group 16.2.7 16. Clock Synchronous Serial Interface SCS Pin Control and Arbitration When setting the SSUMS bit in the SSMR2 register to 1 (4-wire bus communication mode) and the CSS1 bit in the SSMR2 register to 1 (functions as SCS output pin), set the MSS bit in the SSCRH register to 1 (operates as the master device) and check the arbitration of the SCS pin before starting serial transfer. If clock synchronous serial I/O with chip select detects that the synchronized internal SCS signal is held "L" in this period, the CE bit in the SSSR register is set to 1 (conflict error) and the MSS bit is automatically set to 0 (operates as a slave device). Figure 16.21 shows the Arbitration Check Timing. Future transmit operations are not performed while the CE bit is set to 1. Set the CE bit to 0 (no conflict error) before starting transmission. SCS input Internal SCS (synchronization) MSS bit in SSCRH register 1 0 Transfer start Data write to SSTDR register CE High-impedance SCS output Maximum time of SCS internal synchronization During arbitration detection Figure 16.21 Arbitration Check Timing Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 288 of 453 R8C/26 Group, R8C/27 Group 16.2.8 16. Clock Synchronous Serial Interface Notes on Clock Synchronous Serial I/O with Chip Select Set the IICSEL bit in the PMR register to 0 (select clock synchronous serial I/O with chip select function) to use the clock synchronous serial I/O with chip select function. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 289 of 453 R8C/26 Group, R8C/27 Group 16.3 16. Clock Synchronous Serial Interface I2C bus Interface The I2C bus interface is the circuit that performs serial communication based on the data transfer format of the Philips I2C bus. Table 16.5 lists the Specifications of I2C bus Interface, Figure 16.22 shows a Block Diagram of I2C bus Interface, and Figure 16.23 shows the External Circuit Connection Example of Pins SCL and SDA. Figures 16.24 to 16.30 show the registers associated with the I2C bus interface. * I2C bus is a trademark of Koninklijke Philips Electronics N. V. Table 16.5 Specifications of I2C bus Interface Item Specification 2 Communication formats * I C bus format - Selectable as master/slave device - Continuous transmit/receive operation (because the shift register, transmit data register, and receive data register are independent) - Start/stop conditions are automatically generated in master mode - Automatic loading of acknowledge bit during transmission - Bit synchronization/wait function (In master mode, the state of the SCL signal is monitored per bit and the timing is synchronized automatically. If the transfer is not possible yet, the SCL signal goes "L" and the interface stands by.) - Support for direct drive of pins SCL and SDA (N-channel open drain output) * Clock synchronous serial format - Continuous transmit/receive operation (because the shift register, transmit data register, and receive data register are independent) I/O pins SCL (I/O): Serial clock I/O pin SDA (I/O): Serial data I/O pin Transfer clocks * When the MST bit in the ICCR1 register is set to 0 The external clock (input from the SCL pin) * When the MST bit in the ICCR1 register is set to 1 The internal clock selected by bits CKS0 to CKS3 in the ICCR1 register (output from the SCL pin) Receive error detection * Overrun error detection (clock synchronous serial format) Indicates an overrun error during reception. When the last bit of the next data item is received while the RDRF bit in the ICSR register is set to 1 (data in the ICDRR register), the AL bit is set to 1. 2 Interrupt sources * I C bus format ................................ 6 sources(1) Transmit data empty (including when slave address matches), transmit ends, receive data full (including when slave address matches), arbitration lost, NACK detection, and stop condition detection. * Clock synchronous serial format .... 4 sources(1) Transmit data empty, transmit ends, receive data full and overrun error 2 Select functions * I C bus format - Selectable output level for acknowledge signal during reception * Clock synchronous serial format - MSB-first or LSB-first selectable as data transfer direction NOTE: 1. All sources use one interrupt vector for I2C bus interface. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 290 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface f1 Transfer clock generation circuit SCL Output control ICCR1 register Transmit/receive control circuit Noise canceller ICCR2 register ICMR register ICDRT register SAR register Output control ICDRS register Noise canceller Address comparison circuit Data bus SDA ICDRR register Bus state judgment circuit Arbitration judgment circuit ICSR register ICIER register Interrupt generation circuit Interrupt request (TXI, TEI, RXI, STPI, NAKI) Figure 16.22 Block Diagram of I2C bus Interface Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 291 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface VCC VCC SCL SCL SDA SDA SCL input SCL output SDA input SDA output SCL (Master) SCL SCL input SCL input SCL output SCL output SDA SDA input SDA output SDA output (Slave 1) Figure 16.23 SDA SDA input (Slave 2) External Circuit Connection Example of Pins SCL and SDA Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 292 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface IIC bus Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICCR1 Bit Symbol CKS0 CKS1 CKS2 CKS3 TRS Address 00B8h Bit Name Transmit clock select bits 3 to b3 b2 b1 b0 0 0 0 0 : f1/28 0(1) 0 0 0 1 : f1/40 0 0 1 0 : f1/48 0 0 1 1 : f1/64 0 1 0 0 : f1/80 0 1 0 1 : f1/100 0 1 1 0 : f1/112 0 1 1 1 : f1/128 1 0 0 0 : f1/56 1 0 0 1 : f1/80 1 0 1 0 : f1/96 1 0 1 1 : f1/128 1 1 0 0 : f1/160 1 1 0 1 : f1/200 1 1 1 0 : f1/224 1 1 1 1 : f1/256 Transfer/receive select bit(2, 3, 6) Master/slave select bit(5, 6) MST Receive disable bit RCVD IIC bus interface enable bit ICE After Reset 00h Function RW RW RW RW RW b5 b4 0 0 : Slave Receive Mode(4) 0 1 : Slave Transmit Mode 1 0 : Master Receive Mode 1 1 : Master Transmit Mode RW RW After reading the ICDRR register w hile the TRS bit is set to 0 0 : Maintains the next receive operation 1 : Disables the next receive operation RW 0 : This module is halted (Pins SCL and SDA are set to port function) 1 : This module is enabled for transfer operations (Pins SCL and SDA are bus drive state) RW NOTES: 1. Set according to the necessary transfer rate in master mode. Refer to Table 16.6 Transfer Rate Exam ples for the transfer rate. This bit is used for maintaining of the setup time in transmit mode of slave mode. The time is 10Tcyc w hen the CKS3 bit is set to 0 and 20Tcyc w hen the CKS3 bit is set to 1. (1Tcyc = 1/f1(s)) 2. Rew rite the TRS bit betw een transfer frames. 3. When the first 7 bit after the start condition in slave receive mode match w ith the slave address set in the SAR register and the 8th bit is set to 1, the TRS bit is set to 1. 4. In master mode w ith the I2C bus format, w hen arbitration is lost, bits MST and TRS are set to 0 and the IIC enters slave receive mode. 5. When an overrun error occurs in master receive mode of the clock synchronous serial format, the MST bit is set to 0 and the IIC enters slave receive mode. 6. In multimaster operation use the MOV instruction to set bits TRS and MST. Figure 16.24 ICCR1 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 293 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface IIC bus Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 00B9h ICCR2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b0) When read, the content is 1. IIC control part reset bit IICRST -- (b2) SCLO SDAOP SDAO SCP After Reset 01111101b Function When hang-up occurs due to communication failure during I2C bus interface operation, w rite 1, to reset the control block of the I2C bus interface w ithout setting ports or initializing registers. SCL monitor flag SDAO w rite protect bit RW -- 0 : SCL pin is set to "L" 1 : SCL pin is set to "H" RO (1) When rew rite to SDAO bit, w rite 0 simultaneously. When read, the content is 1. SDA output value control When read bit 0 : SDA pin output is held "L" 1 : SDA pin output is held "H" When w ritten(1,2) 0 : SDA pin output is changed to "L" 1 : SDA pin output is changed to high-impedance ("H" output via external pull-up resistor) RW RW Start/stop condition generation disable bit When w riting to the to BBSY bit, w rite 0 simultaneously.(3) When read, the content is 1. Writing 1 is invalid. RW Bus busy bit(4) When read 0 : Bus is in released state (SDA signal changes from "L" to "H" w hile SCL signal is in "H" state) 1 : Bus is in occupied state (SDA signal changes from "H" to "L" w hile SCL signal is in "H" state) When w ritten(3) 0 : Generates stop condition 1 : Generates start condition RW NOTES: 1. When w riting to the SDAO bit, w rite 0 to the SDAOP bit using the MOV instruction simultaneously. 2. Do not w rite during a transfer operation. 3. This bit is enabled in master mode. When w riting to the BBSY bit, w rite 0 to the SCP bit using the MOV instruction simultaneously. Execute the same w ay w hen the start condition is regenerating. 4. This bit is disabled w hen the clock synchronous serial format is used. ICCR2 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 -- Nothing is assigned. If necessary, set to 0. When read, the content is 1. BBSY Figure 16.25 RW Page 294 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface IIC bus Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol ICMR Bit Symbol Address 00BAh Bit Name Bits counter 2 to 0 After Reset 00011000b Function I2C bus format (remaining transfer bit count w hen read out and data bit count of next transfer w hen w ritten).(1,2) RW b2 b1 b0 0 0 0 : 9 bits (3) 0 0 1 : 2 bits 0 1 0 : 3 bits 0 1 1 : 4 bits 1 0 0 : 5 bits 1 0 1 : 6 bits 1 1 0 : 7 bits 1 1 1 : 8 bits Clock synchronous serial format (w hen read, the remaining transfer bit count and w hen w ritten 000b). BC0 BC1 RW RW b2 b1 b0 0 0 0 : 8 bits 0 0 1 : 1 bit 0 1 0 : 2 bits 0 1 1 : 3 bits 1 0 0 : 4 bits 1 0 1 : 5 bits 1 1 0 : 6 bits 1 1 1 : 7 bits BC2 BC w rite protect bit BCWP When rew riting bits BC0 to BC2, w rite 0 simultaneously.(2,4) When read, the content is 1. Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- (b5) Reserved bit Set to 0. Wait insertion bit(5) 0 : No w ait (Transfer data and acknow ledge bit consecutively) 1 : Wait (After the clock falls for the final data bit, "L" period is extended for tw o transfer clocks cycles) RW 0 : Data transfer w ith MSB-first(6) 1 : Data transfer w ith LSB-first RW MLS MSB-first/LSB-first select bit NOTES: 1. Rew rite betw een transfer frames. When w riting values other than 000b, w rite w hen the SCL signal is "L". 2. When w riting to bits BC0 to BC2, w rite 0 to the BCWP bit using the MOV instruction. 3. After data including the acknow ledge bit is transferred, these bits are automatically set to 000b. When the start condition is detected, these bits are automatically set to 000b. 4. Do not rew rite w hen the clock synchronous serial format is used. 5. The setting value is enabled in master mode of the I2C bus format. It is disabled in slave mode of the I2C bus format or w hen the clock synchronous serial format is used. 6. Set to 0 w hen the I2C bus format is used. ICMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW -- (b4) WAIT Figure 16.26 RW Page 295 of 453 -- RW R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface IIC bus Interrupt Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICIER Bit Symbol ACKBT Address 00BBh Bit Name Transmit acknow ledge select bit After Reset 00h Function 0 : 0 is transmitted as acknow ledge bit in receive mode. 1 : 1 is transmitted as acknow ledge bit in receive mode. Receive acknow ledge bit 0 : Acknow ledge bit received from receive device in transmit mode is set to 0. 1 : Acknow ledge bit received from receive device in transmit mode is set to 1. ACKBR ACKE Acknow ledge bit judgment 0 : Value of receive acknow ledge bit is ignored select bit and continuous transfer is performed. 1 : When receive acknow ledge bit is set to 1, continuous transfer is halted. RW RW RO RW Stop condition detection interrupt enable bit 0 : Disables stop condition detection interrupt request 1 : Enables stop condition detection interrupt request(2) RW NACK receive interrupt enable bit 0 : Disables NACK receive interrupt request and arbitration lost/overrun error interrupt request 1 : Enables NACK receive interrupt request and arbitration lost/overrun error interrupt request(1) RW Receive interrupt enable bit 0 : Disables receive data full and overrun error interrupt request 1 : Enables receive data full and overrun error interrupt request(1) RW TEIE Transmit end interrupt enable bit 0 : Disables transmit end interrupt request 1 : Enables transmit end interrupt request RW TIE Transmit interrupt enable bit 0 : Disables transmit data empty interrupt request 1 : Enables transmit data empty interrupt request RW STIE NAKIE RIE NOTES: 1. An overrun error interrupt request is generated w hen the clock synchronous format is used. 2. Set the STIE bit to 1 (enable stop condition detection interrupt request) w hen the STOP bit in the ICSR register is set to 0. Figure 16.27 ICIER Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 296 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface IIC bus Status Register(7) b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICSR Bit Symbol ADZ AAS Address 00BCh Bit Name General call address recognition flag(1,2) Slave address recognition This flag is set to 1 w hen the first frame follow ing flag(1) start condition matches bits SVA0 to SVA6 in the SAR register in slave receive mode. (Detect the slave address and generate call address) RDRF RW RW RW When the stop condition is detected after the frame is transferred, this flag is set to 1 RW No acknow ledge detection When no acknow ledge is detected from the receive flag(1,4) device after transmission, this flag is set to 1 RW AL NACKF RW When the I2C bus format is used, this flag indicates that arbitration has been lost in master mode. In the follow ing cases, this flag is set to 1.(3) * When the internal SDA signal and SDA pin level do not match at the rise of the SCL signal in master transmit mode * When the start condition is detected and the SDA pin is held "H" in master transmit/receive mode This flag indicates an overrun error w hen the clock synchronous format is used. In the follow ing case, this flag is set to 1. * When the last bit of the next data item is received w hile the RDRF bit is set to 1 Arbitration lost flag/overrun error flag(1) STOP After Reset 0000X000b Function When the general call address is detected, this flag is set to 1. Stop condition detection flag(1) Receive data register full(1,5) When receive data is transferred from in registers ICDRS to ICDRR , this flag is set to 1 RW Transmit end(1,6) When the 9th clock cycle of the SCL signal in the I2C bus format occurs w hile the TDRE bit is set to 1, this flag is set to 1. This flag is set to 1 w hen the final bit of the transmit frame is transmitted in the clock synchronous format. RW In the follow ing cases, this flag is set to 1. * Data is transferred from registers ICDRT to ICDRS and the ICDRT register is empty * When setting the TRS bit in the ICCR1 register to 1 (transmit mode) * When generating the start condition (including retransmit) * When changing from slave receive mode to slave transmit mode RW TEND Transmit data empty (1,6) TDRE NOTES: 1. Each bit is set to 0 by reading 1 before w riting 0. 2. This flag is enabled in slave receive mode of the I2C bus format. 3. When tw o or more master devices attempt to occupy the bus at nearly the same time, if the I2C bus Interface monitors the SDA pin and the data w hich the I2C bus Interface transmits is different, the AL flag is set to 1 and the bus is occupied by the another master. 4. The NACKF bit is enabled w hen the ACKE bit in the ICIER register is set to 1 (w hen the receive acknow ledge bit is set to 1, transfer is halted). 5. The RDRF bit is set to 0 w hen reading data from the ICDRR register. 6. Bits TEND and TDRE are set to 0 w hen w riting data to the ICDRT register. 7. When accessing the ICSR register continuously, insert one or more NOP instructions betw een the instructions to access it. Figure 16.28 ICSR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 297 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Slave Address Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol SAR Bit Symbol FS SVA0 SVA1 SVA2 SVA3 SVA4 SVA5 SVA6 Address 00BDh Bit Name Format select bit Slave address 6 to 0 After Reset 00h Function RW 0 : I2C bus format 1 : Clock synchronous serial format RW Set an address different from that of the other slave devices w hich are connected to the I2C bus. When the 7 high-order bits of the first frame transmitted after the starting condition match bits SVA0 to SVA6 in slave mode of the I2C bus format, the MCU operates as a slave device. RW RW RW RW RW RW RW IIC bus Transmit Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICDRT Address 00BEh After Reset FFh Function Store transmit data When it is detected that the ICDRS register is empty, the stored transmit data item is transferred to the ICDRS register and data transmission starts. When the next transmit data item is w ritten to the ICDRT register during transmission of the data in the ICDRS register, continuous transmit is enabled. When the MLS bit in the ICMR register is set to 1 (data transferred LSB-first) and after the data is w ritten to the ICDRT register, the MSB-LSB inverted data is read. RW RW IIC bus Receive Data Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICDRR Address 00BFh After Reset FFh Function Store receive data When the ICDRS register receives 1 byte of data, the receive data is transferred to the ICDRR register and the next receive operation is enabled. RW RO IIC bus Shift Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol ICDRS Function This register is used to transmit and receive data. The transmit data is transferred from registers ICRDT to the ICDRS and data is transmitted from the SDA pin w hen transmitting. After 1 byte of data is received, data is transferred from registers ICDRS to ICDRR w hile receiving. Figure 16.29 Registers SAR, ICDRT, ICDRR, and ICDRS Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 298 of 453 RW -- R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Port Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol PMR Bit Symbol INT1SEL -- (b2-b1) SSISEL U1PINSEL TXD1SEL TXD1EN IICSEL Address 00F8h Bit Name _____ INT1 pin select bit After Reset 00h Function 0 : P1_5, P1_7 1 : P3_6 Nothing is assigned. If necessary, set to 0. When read, the content is 0. SSI pin select bit 0 : P3_3 1 : P1_6 RW TXD1 pin sw itch bit(1) 0 : P0_0 1 : P3_6, P3_7 RW Port/TXD1 pin sw itch bit(1) 0 : Programmable I/O port 1 : TXD1 RW TXD1/RXD1 select bit(1) 0 : RXD1 1 : TXD1 RW SSU / I2C bus pin sw itch bit 0 : Selects SSU function 1 : Selects I2C bus function RW Pin Function U1PINSEL bit PMR Register TXD1SEL bit x x 0 1 P3_7(TXD1) 00b P3_7(RXD1) P0_0(TXD1) 01b P3_7(TXD1) P4_5(RXD1) P3_6(TXD1) 10b P3_6(RXD1) P0_0(TXD1) x: 0 or 1 Figure 16.30 PMR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW -- NOTE: 1. The UART1 pins can be selected by using bits U1PINSEL, TXD1SEL and TXD1EN, and bits UART1SEL1 and UART1SEL0 in the PINSR1 register. PINSR1 Register UART1SEL1, UART1SEL0 bit RW Page 299 of 453 1 1 x x x 0 1 TXD1EN bit 1 0 x x 1 0 x R8C/26 Group, R8C/27 Group 16.3.1 16. Clock Synchronous Serial Interface Transfer Clock When the MST bit in the ICCR1 register is set to 0, the transfer clock is the external clock input from the SCL pin. When the MST bit in the ICCR1 register is set to 1, the transfer clock is the internal clock selected by bits CKS0 to CKS3 in the ICCR1 register and the transfer clock is output from the SCL pin. Table 16.6 lists the Transfer Rate Examples. Table 16.6 Transfer Rate Examples ICCR1 Register Transfer CKS3 CKS2 CKS1 CKS0 Clock f1 = 5 MHz 0 0 0 0 f1/28 179 kHz 1 f1/40 125 kHz 1 0 f1/48 104 kHz 1 f1/64 78.1 kHz 1 0 0 f1/80 62.5 kHz 1 f1/100 50.0 kHz 1 0 f1/112 44.6 kHz 1 f1/128 39.1 kHz 1 0 0 0 f1/56 89.3 kHz 1 f1/80 62.5 kHz 1 0 f1/96 52.1 kHz 1 f1/128 39.1 kHz 1 0 0 f1/160 31.3 kHz 1 f1/200 25.0 kHz 1 0 f1/224 22.3 kHz 1 f1/256 19.5 kHz Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 300 of 453 f1 = 8 MHz 286 kHz 200 kHz 167 kHz 125 kHz 100 kHz 80.0 kHz 71.4 kHz 62.5 kHz 143 kHz 100 kHz 83.3 kHz 62.5 kHz 50.0 kHz 40.0 kHz 35.7 kHz 31.3 kHz Transfer Rate f1 = 10 MHz f1 = 16 MHz f1 = 20 MHz 357 kHz 571 kHz 714 kHz 250 kHz 400 kHz 500 kHz 208 kHz 333 kHz 417 kHz 156 kHz 250 kHz 313 kHz 125 kHz 200 kHz 250 kHz 100 kHz 160 kHz 200 kHz 89.3 kHz 143 kHz 179 kHz 78.1 kHz 125 kHz 156 kHz 179 kHz 286 kHz 357 kHz 125 kHz 200 kHz 250 kHz 104 kHz 167 kHz 208 kHz 78.1 kHz 125 kHz 156 kHz 62.5 kHz 100 kHz 125 kHz 50.0 kHz 80.0 kHz 100 kHz 44.6 kHz 71.4 kHz 89.3 kHz 39.1 kHz 62.5 kHz 78.1 kHz R8C/26 Group, R8C/27 Group 16.3.2 16. Clock Synchronous Serial Interface Interrupt Requests I2 C The bus interface has six interrupt requests when the I2C bus format is used and four interrupt requests when the clock synchronous serial format is used. Table 16.7 lists the Interrupt Requests of I2C bus Interface. Since these interrupt requests are allocated at the I2C bus interface interrupt vector table, determining the source bit by bit is necessary. Table 16.7 Interrupt Requests of I2C bus Interface Interrupt Request Generation Condition Format I2C bus Transmit data empty Transmit ends Receive data full Stop condition detection NACK detection Arbitration lost/overrun error TXI TEI RXI STPI NAKI TIE = 1 and TDRE = 1 TEIE = 1 and TEND = 1 RIE = 1 and RDRF = 1 STIE = 1 and STOP = 1 NAKIE = 1 and AL = 1 (or NAKIE = 1 and NACKF = 1) Enabled Enabled Enabled Enabled Enabled Enabled Clock Synchronous Serial Enabled Enabled Enabled Disabled Disabled Enabled STIE, NAKIE, RIE, TEIE, TIE: Bits in ICIER register AL, STOP, NACKF, RDRF, TEND, TDRE: Bits in ICSR register When the generation conditions listed in Table 16.7 are met, an I2C bus interface interrupt request is generated. Set the interrupt generation conditions to 0 by the I2C bus interface interrupt routine. However, bits TDRE and TEND are automatically set to 0 by writing transmit data to the ICDRT register and the RDRF bit is automatically set to 0 by reading the ICDRR register. When writing transmit data to the ICDRT register, the TDRE bit is set to 0. When data is transferred from registers ICDRT to ICDRS, the TDRE bit is set to 1 and by further setting the TDRE bit to 0, 1 additional byte may be transmitted. Set the STIE bit to 1 (enable stop condition detection interrupt request) when the STOP bit is set to 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 301 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface I2C bus Interface Mode 16.3.3 I2C bus Format 16.3.3.1 Setting the FS bit in the SAR register to 0 enable communication in I2C bus format. Figure 16.31 shows the I2C bus Format and Bus Timing. The 1st frame following the start condition consists of 8 bits. (1) I2C bus format (a) I2C bus format (FS = 0) S SLA R/W A DATA A A/A P 1 7 1 1 n 1 1 1 Transfer bit count (n = 1 to 8) 1 m Transfer frame count (m = from 1) (b) I2C bus format (when start condition is retransmitted, FS = 0) S SLA R/W A DATA A/A S SLA R/W A DATA A/A P 1 7 1 1 n1 1 1 7 1 1 n2 1 1 1 1 m1 m2 Upper: Transfer bit count (n1, n2 = 1 to 8) Lower: Transfer frame count (m1, m2 = 1 or more) (2) I2C bus timing SDA SCL 1 to 7 S SLA 8 R/W 9 1 to 7 A 8 DATA 9 1 to 7 A 8 DATA 9 A Explanation of symbols S : Start condition The master device changes the SDA signal from "H" to "L" while the SCL signal is held "H". SLA : Slave address R/W : Indicates the direction of data transmit/receive Data is transmitted from the slave device to the master device when R/W value is 1 and from the master device to the slave device when R/W value is 0. A : Acknowledge The receive device sets the SDA signal to "L". DATA : Transmit / receive data P : Stop condition The master device changes the SDA signal from "L" to "H" while the SCL signal is held "H". Figure 16.31 I2C bus Format and Bus Timing Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 302 of 453 P R8C/26 Group, R8C/27 Group 16.3.3.2 16. Clock Synchronous Serial Interface Master Transmit Operation In master transmit mode, the master device outputs the transmit clock and data, and the slave device returns an acknowledge signal. Figures 16.32 and 16.33 show the Operating Timing in Master Transmit Mode (I2C bus Interface Mode). The transmit procedure and operation in master transmit mode are as follows. (1) Set the STOP bit in the ICSR register to 0 to reset it. Then set the ICE bit in the ICCR1 register to 1 (transfer operation enabled). Then set bits WAIT and MLS in the ICMR register and set bits CKS0 to CKS3 in the ICCR1 register (initial setting). (2) Read the BBSY bit in the ICCR2 register to confirm that the bus is free. Set bits TRS and MST in the ICCR1 register to master transmit mode. The start condition is generated by writing 1 to the BBSY bit and 0 to the SCP bit by the MOV instruction. (3) After confirming that the TDRE bit in the ICSR register is set to 1 (data is transferred from registers ICDRT to ICDRS), write transmit data to the ICDRT register (data in which a slave address and R/W are indicated in the 1st byte). At this time, the TDRE bit is automatically set to 0, data is transferred from registers ICDRT to ICDRS, and the TDRE bit is set to 1 again. (4) When transmission of 1 byte of data is completed while the TDRE bit is set to 1, the TEND bit in the ICSR register is set to 1 at the rise of the 9th transmit clock pulse. Read the ACKBR bit in the ICIER register, and confirm that the slave is selected. Write the 2nd byte of data to the ICDRT register. Since the slave device is not acknowledged when the ACKBR bit is set to 1, generate the stop condition. The stop condition is generated by the writing 0 to the BBSY bit and 0 to the SCP bit by the MOV instruction. The SCL signal is held "L" until data is available and the stop condition is generated. (5) Write the transmit data after the 2nd byte to the ICDRT register every time the TDRE bit is set to 1. (6) When writing the number of bytes to be transmitted to the ICDRT register, wait until the TEND bit is set to 1 while the TDRE bit is set to 1. Or wait for NACK (the NACKF bit in the ICSR register is set to 1) from the receive device while the ACKE bit in the ICIER register is set to 1 (when the receive acknowledge bit is set to 1, transfer is halted). Then generate the stop condition before setting bits TEND and NACKF to 0. (7) When the STOP bit in the ICSR register is set to 1, return to slave receive mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 303 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface SCL (master output) 1 2 3 4 5 6 7 8 SDA (master output) b7 b6 b5 b4 b3 b2 b1 b0 Slave address 9 2 b7 b6 R/W SDA (slave output) TDRE bit in ICSR register 1 A 1 0 TEND bit in ICSR register 1 0 ICDRT register Address + R/W ICDRS register (2) Instruction of start condition generation Processing by program Figure 16.32 Data 1 Address + R/W (3) Data write to ICDRT register (1st byte) Data 2 Data 1 (5) Data write to ICDRT register (3rd byte) (4) Data write to ICDRT register (2nd byte) Operating Timing in Master Transmit Mode (I2C bus Interface Mode) (1) SCL (master output) 9 SDA (master output) SDA (slave output) TDRE bit in ICSR register 1 2 3 4 5 6 7 8 b7 b6 b5 b4 b3 b2 b1 b0 A 9 A/A 1 0 TEND bit in ICSR register 1 0 ICDRT register Data n ICDRS register Processing by program Figure 16.33 Data n (3) Data write to ICDRT register (6) Generate stop condition and set TEND bit to 0 (7) Set to slave receive mode Operating Timing in Master Transmit Mode (I2C bus Interface Mode) (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 304 of 453 R8C/26 Group, R8C/27 Group 16.3.3.3 16. Clock Synchronous Serial Interface Master Receive Operation In master receive mode, the master device outputs the receive clock, receives data from the slave device, and returns an acknowledge signal. Figures 16.34 and 16.35 show the Operating Timing in Master Receive Mode (I2C bus Interface Mode). The receive procedure and operation in master receive mode are shown below. (1) After setting the TEND bit in the ICSR register to 0, switch from master transmit mode to master receive mode by setting the TRS bit in the ICCR1 register to 0. Also, set the TDRE bit in the ICSR register to 0. (2) When performing the dummy read of the ICDRR register and starting the receive operation, the receive clock is output in synchronization with the internal clock and data is received. The master device outputs the level set by the ACKBT bit in the ICIER register to the SDA pin at the rising edge of the 9th clock cycle of the receive clock. (3) The 1-frame data receive is completed and the RDRF bit in the ICSR register is set to 1 at the rise of the 9th clock cycle. At this time, when reading the ICDRR register, the received data can be read and the RDRF bit is set to 0 simultaneously. (4) Continuous receive operation is enabled by reading the ICDRR register every time the RDRF bit is set to 1. If the 8th clock cycle falls after the ICDRR register is read by another process while the RDRF bit is set to 1, the SCL signal is fixed "L" until the ICDRR register is read. (5) If the next frame is the last receive frame and the RCVD bit in the ICCR1 register is set to 1 (disables the next receive operation) before reading the ICDRR register, stop condition generation is enabled after the next receive operation. (6) When the RDRF bit is set to 1 at the rise of the 9th clock cycle of the receive clock, generate the stop condition. (7) When the STOP bit in the ICSR register is set to 1, read the ICDRR register and set the RCVD bit to 0 (maintain the following receive operation). (8) Return to slave receive mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 305 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Master transmit mode SCL (master output) Master receive mode 9 1 2 3 4 5 6 7 8 SDA (master output) 1 A SDA (slave output) TDRE bit in ICSR register 9 A b7 b6 b5 b4 b3 b2 b1 b7 b0 1 0 TEND bit in ICSR register 1 0 TRS bit in ICCR1 register RDRF bit in ICSR register 1 0 1 0 ICDRS register Data 1 ICDRR register Processing by program Figure 16.34 Data 1 (1) Set TEND and TRS bits to 0 before setting TDRE bits to 0 (2) Read ICDRR register (3) Read ICDRR register Operating Timing in Master Receive Mode (I2C bus Interface Mode) (1) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 306 of 453 R8C/26 Group, R8C/27 Group SCL (master output) 9 SDA (master output) A 1 RCVD bit in ICCR1 register 2 3 4 5 6 7 8 9 A/A SDA (slave output) RDRF bit in ICSR register 16. Clock Synchronous Serial Interface b7 b6 b5 b4 b3 b2 b1 b0 1 0 1 0 ICDRS register Data n-1 Data n Data n-1 ICDRR register Processing by program (5) Set RCVD bit to 1 before reading ICDRR register Data n (6) Stop condition generation (7) Read ICDRR register before setting RCVD bit to 0 (8) Set to slave receive mode Figure 16.35 Operating Timing in Master Receive Mode (I2C bus Interface Mode) (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 307 of 453 R8C/26 Group, R8C/27 Group 16.3.3.4 16. Clock Synchronous Serial Interface Slave Transmit Operation In slave transmit mode, the slave device outputs the transmit data while the master device outputs the receive clock and returns an acknowledge signal. Figures 16.36 and 16.37 show the Operating Timing in Slave Transmit Mode (I2C bus Interface Mode). The transmit procedure and operation in slave transmit mode are as follows. (1) Set the ICE bit in the ICCR1 register to 1 (transfer operation enabled). Set bits WAIT and MLS in the ICMR register and bits CKS0 to CKS3 in the ICCR1 register (initial setting). Set bits TRS and MST in the ICCR1 register to 0 and wait until the slave address matches in slave receive mode. (2) When the slave address matches at the 1st frame after detecting the start condition, the slave device outputs the level set by the ACKBT bit in the ICIER register to the SDA pin at the rise of the 9th clock cycle. At this time, if the 8th bit of data (R/W) is 1, bits TRS and TDRE in the ICSR register are set to 1, and the mode is switched to slave transmit mode automatically. Continuous transmission is enabled by writing transmit data to the ICDRT register every time the TDRE bit is set to 1. (3) When the TDRE bit in the ICDRT register is set to 1 after writing the last transmit data to the ICDRT register, wait until the TEND bit in the ICSR register is set to 1 while the TDRE bit is set to 1. When the TEND bit is set to 1, set the TEND bit to 0. (4) The SCL signal is released by setting the TRS bit to 0 and performing a dummy read of the ICDRR register to end the process. (5) Set the TDRE bit to 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 308 of 453 R8C/26 Group, R8C/27 Group Slave receive mode SCL (master output) 16. Clock Synchronous Serial Interface Slave transmit mode 9 1 2 3 4 5 6 7 8 1 9 SDA (master output) A SCL (slave output) SDA (slave output) TDRE bit in ICSR register A b6 b7 b5 b4 b3 b2 b1 b7 b0 1 0 TEND bit in ICSR register 1 0 TRS bit in ICCR1 register 1 0 ICDRT register Data 1 ICDRS register Data 3 Data 2 Data 1 Data 2 ICDRR register (1) Data write to ICDRT register (data 1) Processing by program Figure 16.36 (2) Data write to ICDRT register (data 2) (2) Data write to ICDRT register (data 3) Operating Timing in Slave Transmit Mode (I2C bus Interface Mode) (1) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 309 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Slave receive mode Slave transmit mode SCL (master output) 9 SDA (master output) A 1 2 3 4 5 6 7 8 9 A SCL (slave output) SDA (slave output) TDRE bit in ICSR register b7 b6 b5 b4 b3 b2 b1 b0 1 0 TEND bit in ICSR register 1 0 TRS bit in ICCR1 register 1 0 ICDRT register Data n Data n ICDRS register ICDRR register Processing by program Figure 16.37 (3) Set the TEND bit to 0 (4) Dummy read of ICDRR register after setting TRS bit to 0 (5) Set TDRE bit to 0 Operating Timing in Slave Transmit Mode (I2C bus Interface Mode) (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 310 of 453 R8C/26 Group, R8C/27 Group 16.3.3.5 16. Clock Synchronous Serial Interface Slave Receive Operation In slave receive mode, the master device outputs the transmit clock and data, and the slave device returns an acknowledge signal. Figures 16.38 and 16.39 show the Operating Timing in Slave Receive Mode (I2C bus Interface Mode). The receive procedure and operation in slave receive mode are as follows. (1) Set the ICE bit in the ICCR1 register to 1 (transfer operation enabled). Set bits WAIT and MLS in the ICMR register and bits CKS0 to CKS3 in the ICCR1 register (initial setting). Set bits TRS and MST in the ICCR1 register to 0 and wait until the slave address matches in slave receive mode. (2) When the slave address matches at the 1st frame after detecting the start condition, the slave device outputs the level set in the ACKBT bit in the ICIER register to the SDA pin at the rise of the 9th clock cycle. Since the RDRF bit in the ICSR register is set to 1 simultaneously, perform the dummy-read (the read data is unnecessary because it indicates the slave address and R/W). (3) Read the ICDRR register every time the RDRF bit is set to 1. If the 8th clock cycle falls while the RDRF bit is set to 1, the SCL signal is fixed "L" until the ICDRR register is read. The setting change of the acknowledge signal returned to the master device before reading the ICDRR register takes affect from the following transfer frame. (4) Reading the last byte is performed by reading the ICDRR register in like manner. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 311 of 453 R8C/26 Group, R8C/27 Group SCL (master output) 16. Clock Synchronous Serial Interface 9 1 SDA (master output) 2 3 b6 b7 4 5 b4 b5 6 7 b2 b3 8 b7 b0 b1 1 9 SCL (slave output) SDA (slave output) RDRF bit in ICSR register A A 1 0 ICDRS register Data 2 Data 1 ICDRR register Processing by program Figure 16.38 Data 1 (2) Read ICDRR register (2) Dummy read of ICDRR register Operating Timing in Slave Receive Mode (I2C bus Interface Mode) (1) SCL (master output) 9 SDA (master output) 1 b7 3 2 b6 b5 4 5 b4 b3 6 b2 7 b1 8 9 b0 SCL (slave output) SDA (slave output) RDRF bit in ICSR register A A 1 0 ICDRS register Data 2 Data 1 ICDRR register Processing by program Figure 16.39 Data 1 (3) Set ACKBT bit to 1 (3) Read ICDRR register (4) Read ICDRR register Operating Timing in Slave Receive Mode (I2C bus Interface Mode) (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 312 of 453 R8C/26 Group, R8C/27 Group 16.3.4 16. Clock Synchronous Serial Interface Clock Synchronous Serial Mode 16.3.4.1 Clock Synchronous Serial Format Set the FS bit in the SAR register to 1 to use the clock synchronous serial format for communication. Figure 16.40 shows the Transfer Format of Clock Synchronous Serial Format. When the MST bit in the ICCR1 register is set to 1, the transfer clock is output from the SCL pin, and when the MST bit is set to 0, the external clock is input. The transfer data is output between successive falling edges of the SCL clock, and data is determined at the rising edge of the SCL clock. MSB-first or LSB-first can be selected as the order of the data transfer by setting the MLS bit in the ICMR register. The SDA output level can be changed by the SDAO bit in the ICCR2 register during transfer standby. SCL SDA Figure 16.40 b0 b1 b2 b3 b4 b5 Transfer Format of Clock Synchronous Serial Format Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 313 of 453 b6 b7 R8C/26 Group, R8C/27 Group 16.3.4.2 16. Clock Synchronous Serial Interface Transmit Operation In transmit mode, transmit data is output from the SDA pin in synchronization with the falling edge of the transfer clock. The transfer clock is output when the MST bit in the ICCR1 register is set to 1 and input when the MST bit is set to 0. Figure 16.41 shows the Operating Timing in Transmit Mode (Clock Synchronous Serial Mode). The transmit procedure and operation in transmit mode are as follows. (1) Set the ICE bit in the ICCR1 register to 1 (transfer operation enabled). Set bits CKS0 to CKS3 in the ICCR1 register and set the MST bit (initial setting). (2) The TDRE bit in the ICSR register is set to 1 by selecting transmit mode after setting the TRS bit in the ICCR1 register to 1. (3) Data is transferred from registers ICDRT to ICDRS and the TDRE bit is automatically set to 1 by writing transmit data to the ICDRT register after confirming that the TDRE bit is set to 1. Continuous transmission is enabled by writing data to the ICDRT register every time the TDRE bit is set to 1. When switching from transmit to receive mode, set the TRS bit to 0 while the TDRE bit is set to 1. SCL 1 SDA (output) TRS bit in ICCR1 register TDRE bit in ICSR register b0 7 2 b1 b6 8 b7 1 b0 7 b6 8 1 b7 b0 1 0 1 0 ICDRT register ICDRS register Processing by program Data 2 Data 1 Data 1 (3) Data write to ICDRT register Data 3 Data 3 Data 2 (3) Data write to ICDRT register (3) Data write to ICDRT register (3) Data write to ICDRT register (2) Set TRS bit to 1 Figure 16.41 Operating Timing in Transmit Mode (Clock Synchronous Serial Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 314 of 453 R8C/26 Group, R8C/27 Group 16.3.4.3 16. Clock Synchronous Serial Interface Receive Operation In receive mode, data is latched at the rising edge of the transfer clock. The transfer clock is output when the MST bit in the ICCR1 register is set to 1 and input when the MST bit is set to 0. Figure 16.42 shows the Operating Timing in Receive Mode (Clock Synchronous Serial Mode). The receive procedure and operation in receive mode are as follows. (1) Set the ICE bit in the ICCR1 register to 1 (transfer operation enabled). Set bits CKS0 to CKS3 in the ICCR1 register and set the MST bit (initial setting). (2) The output of the receive clock starts when the MST bit is set to 1 while the transfer clock is being output. (3) Data is transferred from registers ICDRS to ICDRR and the RDRF bit in the ICSR register is set to 1, when the receive operation is completed. Since the next byte of data is enabled when the MST bit is set to 1, the clock is output continuously. Continuous receive is enabled by reading the ICDRR register every time the RDRF bit is set to 1. An overrun is detected at the rise of the 8th clock cycle while the RDRF bit is set to 1, and the AL bit in the ICSR register is set to 1. At this time, the last receive data is retained in the ICDRR register. (4) When the MST bit is set to 1, set the RCVD bit in the ICCR1 register to 1 (disables the next receive operation) and read the ICDRR register. The SCL signal is fixed "H" after reception of the following byte of data is completed. SCL 1 SDA (input) MST bit in ICCR1 register TRS bit in ICCR1 register b0 2 b1 7 b6 8 b7 1 b0 7 b6 8 1 b7 2 b0 1 0 1 0 RDRF bit in ICSR register 1 0 Data 1 ICDRS register Data 1 ICDRR register Processing by program Figure 16.42 Data 2 (2) Set MST bit to 1 (when transfer clock is output) (3) Read ICDRR register Data 3 Data 2 (3) Read ICDRR register Operating Timing in Receive Mode (Clock Synchronous Serial Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 315 of 453 R8C/26 Group, R8C/27 Group 16.3.5 16. Clock Synchronous Serial Interface Noise Canceller The states of pins SCL and SDA are routed through the noise canceller before being latched internally. Figure 16.43 shows a Block Diagram of Noise Canceller. The noise canceller consists of two cascaded latch and match detector circuits. When the SCL pin input signal (or SDA pin input signal) is sampled on f1 and two latch outputs match, the level is passed forward to the next circuit. When they do not match, the former value is retained. f1 (sampling clock) C SCL or SDA input signal D C Q D Latch Period of f1 f1 (sampling clock) Figure 16.43 Block Diagram of Noise Canceller Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 316 of 453 Q Latch Match detection circuit Internal SCL or SDA signal R8C/26 Group, R8C/27 Group 16.3.6 16. Clock Synchronous Serial Interface Bit Synchronization Circuit When setting the I2C bus interface to master mode, the high-level period may become shorter in the following two cases: * If the SCL signal is driven L level by a slave device * If the rise speed of the SCL signal is reduced by a load (load capacity or pull-up resistor) on the SCL line. Therefore, the SCL signal is monitored and communication is synchronized bit by bit. Figure 16.44 shows the Timing of Bit Synchronization Circuit and Table 16.8 lists the Time between Changing SCL Signal from "L" Output to High-Impedance and Monitoring of SCL Signal. Reference clock of SCL monitor timing SCL VIH Internal SCL Figure 16.44 Timing of Bit Synchronization Circuit Table 16.8 Time between Changing SCL Signal from "L" Output to High-Impedance and Monitoring of SCL Signal ICCR1 Register CKS3 0 1 Time for Monitoring SCL CKS2 0 1 0 1 1Tcyc = 1/f1(s) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 317 of 453 7.5Tcyc 19.5Tcyc 17.5Tcyc 41.5Tcyc R8C/26 Group, R8C/27 Group 16.3.7 16. Clock Synchronous Serial Interface Examples of Register Setting Figures 16.45 to 16.48 show Examples of Register Setting When Using I2C bus interface. Start * Set the STOP bit in the ICSR register to 0 * Set the IICSEL bit in the PMR register to 1 Initial setting Read BBSY bit in ICCR2 register (1) Judge the state of the SCL and SDA lines No (1) (2) Set to master transmit mode BBSY = 0 ? (3) Generate the start condition Yes ICCR1 register TRS bit 1 MST bit 1 (2) ICCR2 register SCP bit 0 BBSY bit 1 (3) (4) Set the transmit data of the 1st byte (slave address + R/W) (5) Wait for 1 byte to be transmitted Write transmit data to ICDRT register (4) (6) Judge the ACKBR bit from the specified slave device (7) Set the transmit data after 2nd byte (except the last byte) (8) Wait until the ICRDT register is empty Read TEND bit in ICSR register (9) Set the transmit data of the last byte No (5) TEND = 1 ? (10) Wait for end of transmission of the last byte (11) Set the TEND bit to 0 Yes Read ACKBR bit in ICIER register (12) Set the STOP bit to 0 (13) Generate the stop condition ACKBR = 0 ? No (6) (15) Set to slave receive mode Set the TDRE bit to 0 Yes Transmit mode ? (14) Wait until the stop condition is generated No Master receive mode Yes Write transmit data to ICDRT register (7) Read TDRE bit in ICSR register No (8) TDRE = 1 ? Yes No Last byte ? (9) Yes Write transmit data to ICDRT register Read TEND bit in ICSR register No (10) TEND = 1 ? Yes ICSR register TEND bit 0 (11) ICSR register STOP bit 0 (12) ICCR2 register SCP bit 0 BBSY bit 0 (13) Read STOP bit in ICSR register No (14) STOP = 1 ? Yes ICCR1 register TRS bit 0 MST bit 0 (15) ICSR register TDRE bit 0 End Figure 16.45 Example of Register Setting in Master Transmit Mode (I2C bus Interface Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 318 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Master receive mode TEND bit 0 ICSR register TRS bit 0 ICCR1 register ICSR register TDRE bit 0 ICIER register ACKBT bit 0 Dummy read in ICDRR register (1) Set the TEND bit to 0 and set to master receive mode. Set the TDRE bit to 0 (1,2) (1) (2) Set the ACKBT bit to the transmit device (1) (3) Dummy read the ICDRR register(1) (2) (3) (4) Wait for 1 byte to be received (5) Judge (last receive - 1) (6) Read the receive data (7) Set the ACKBT bit of the last byte and set to disable continuous receive operation (RCVD = 1)(2) Read RDRF bit in ICSR register No (4) (8) Read the receive data of (last byte - 1) RDRF = 1 ? (9) Wait until the last byte is received Yes (10) Set the STOP bit to 0 Yes Last receive -1? (5) (12) Wait until the stop condition is generated No Read ICDRR register (11) Generate the stop condition (6) (13) Read the receive data of the last byte (14) Set the RCVD bit to 0 ACKBT bit 1 ICIER register (15) Set to slave receive mode (7) ICCR1 register RCVD bit 1 Read ICDRR register (8) Read RDRF bit in ICSR register No (9) RDRF = 1 ? Yes STOP bit 0 ICSR register SCP bit 0 BBSY bit 0 ICCR2 register (10) (11) Read STOP bit in ICSR register (12) No STOP = 1 ? Yes Read ICDRR register (13) ICCR1 register RCVD bit 0 (14) ICCR1 register MST bit 0 (15) End NOTES: 1. Do not generate the interrupt while processing steps (1) to (3). 2. When receiving 1 byte, skip steps (2) to (6) after (1) and jump to process of step (7). processing of step (8) is dummy read of the ICDRR register. Figure 16.46 Example of Register Setting in Master Receive Mode (I2C bus Interface Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 319 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Slave transmit mode AAS bit 0 ICSR register (1) Set the AAS bit to 0 (1) (2) Set the transmit data (except the last byte) Write transmit data to ICDRT register (2) (3) Wait until the ICRDT register is empty (4) Set the transmit data of the last byte Read TDRE bit in ICSR register (5) Wait until the last byte is transmitted No TDRE = 1 ? (3) (7) Set to slave receive mode Yes No (6) Set the TEND bit to 0 (8) Dummy read the ICDRR register to release the SCL signal Last byte ? (4) Yes (9) Set the TDRE bit to 0 Write transmit data to ICDRT register Read TEND bit in ICSR register No TEND = 1 ? ICSR register ICCR1 register Yes TEND bit 0 (6) TRS bit 0 (7) Dummy read in ICDRR register ICSR register (5) TDRE bit 0 (8) (9) End Figure 16.47 Example of Register Setting in Slave Transmit Mode (I2C bus Interface Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 320 of 453 R8C/26 Group, R8C/27 Group 16. Clock Synchronous Serial Interface Slave receive mode AAS bit 0 (1) ICIER register ACKBT bit 0 (2) ICSR register (1) Set the AAS bit to 0 (1) (2) Set the ACKBT bit to the transmit device (3) Dummy read the ICDRR register Dummy read ICDRR register (3) (4) Wait until 1 byte is received (5) Judge (last receive - 1) Read RDRF bit in ICSR register (6) Read the receive data No (4) (7) Set the ACKBT bit of the last byte(1) RDRF = 1 ? (8) Read the receive data of (last byte - 1) Yes (9) Wait until the last byte is received Last receive -1? Yes (5) (10) Read the receive data of the last byte No Read ICDRR register (6) ACKBT bit 1 (7) Read ICDRR register (8) ICIER register Read RDRF bit in ICSR register No (9) RDRF = 1 ? Yes Read ICDRR register (10) End NOTE: 1. When receiving 1 byte, skip steps (2) to (6) after (1) and jump to processing step (7). Processing step (8) is dummy read of the ICDRR register. Figure 16.48 Example of Register Setting in Slave Receive Mode (I2C bus Interface Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 321 of 453 R8C/26 Group, R8C/27 Group 16.3.8 16. Clock Synchronous Serial Interface Notes on I2C bus Interface Set the IICSEL bit in the PMR register to 1 (select I2C bus interface function) to use the I2C bus interface. 16.3.8.1 Multimaster Operation The following actions must be performed to use the I2C bus interface in multimaster operation. * Transfer rate Set the transfer rate by 1/1.8 or faster than the fastest rate of the other masters. For example, if the fastest transfer rate of the other masters is set to 400 kbps, the I2C-bus transfer rate in this MCU should be set to 223 kbps (= 400/1.18) or more. * Bits MST and TRS in the ICCR1 register setting (a) Use the MOV instruction to set bits MST and TRS. (b) When arbitration is lost, confirm the contents of bits MST and TRS. If the contents are other than the MST bit set to 0 and the TRS bit set to 0 (slave receive mode), set the MST bit to 0 and the TRS bit to 0 again. 16.3.8.2 Master Receive Mode Either of the following actions must be performed to use the I2C bus interface in master receive mode. (a) In master receive mode while the RDRF bit in the ICSR register is set to 1, read the ICDRR register before the rising edge of the 8th clock. (b) In master receive mode, set the RCVD bit in the ICCR1 register to 1 (disables the next receive operation) to perform 1-byte communications. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 322 of 453 R8C/26 Group, R8C/27 Group 17. Hardware LIN 17. Hardware LIN The hardware LIN performs LIN communication in cooperation with timer RA and UART0. 17.1 Features The hardware LIN has the features listed below. Figure 17.1 shows a Block Diagram of Hardware LIN. Master mode * Generates Synch Break * Detects bus collision Slave mode * Detects Synch Break * Measures Synch Field * Controls Synch Break and Synch Field signal inputs to UART0 * Detects bus collision NOTE: 1. The WakeUp function is detected by INT1. Hardware LIN Synch Field control circuit RXD0 pin Timer RA TIOSEL = 0 RXD data LSTART bit SBE bit LINE bit RXD0 input control circuit Timer RA underflow signal TIOSEL = 1 Bus collision detection circuit Timer RA interrupt Interrupt control circuit UART0 BCIE, SBIE, and SFIE bits UART0 transfer clock UART0 TE bit Timer RA output pulse MST bit UART0 TXD data TXD0 pin LINE, MST, SBE, LSTART, BCIE, SBIE, SFIE: Bits in LINCR register TIOSEL: Bit in TRAIOC register TE: Bit in U0C1 register Figure 17.1 Block Diagram of Hardware LIN Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 323 of 453 R8C/26 Group, R8C/27 Group 17.2 17. Hardware LIN Input/Output Pins The pin configuration of the hardware LIN is listed in Table 17.1. Table 17.1 Pin Configuration Name Abbreviation Input/Output Receive data input RXD0 Input Transmit data output TXD0 Output Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 324 of 453 Function Receive data input pin of the hardware LIN Transmit data output pin of the hardware LIN R8C/26 Group, R8C/27 Group 17.3 17. Hardware LIN Register Configuration The hardware LIN contains the registers listed below. These registers are detailed in Figures 17.2 and 17.3. * LIN Control Register (LINCR) * LIN Status Register (LINST) LIN Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol LINCR Bit Symbol SFIE Address 0106h Bit Name Synch Field measurementcompleted interrupt enable bit After Reset 00h Function 0 : Disables Synch Field measurementcompleted interrupt 1 : Enables Synch Field measurementcompleted interrupt RW RW SBIE Synch Break detection interrupt 0 : Disables Synch Break detection interrupt 1 : Enables Synch Break detection interrupt enable bit RW BCIE Bus collision detection interrupt 0 : Disables bus collision detection interrupt 1 : Enables bus collision detection interrupt enable bit RW RXDSF LSTART SBE RXD0 input status flag RO Synch Break detection start bit(1) When this bit is set to 1, timer RA input is enabled and RXD0 input is disabled. When read, the content is 0. RW RXD0 input unmasking timing 0 : Unmasked after Synch Break is detected select bit (effective only in slave 1 : Unmasked after Synch Field measurement mode) is completed RW LIN operation mode setting bit(2) MST LINE 0 : RXD0 input enabled 1 : RXD0 input disabled LIN operation start bit 0 : Slave mode (Synch Break detection circuit actuated) 1 : Master mode (Timer RA output OR'ed w ith TXD0) RW 0 : Causes LIN to stop 1 : Causes LIN to start operating(3) RW NOTES: 1. After setting the LSTART bit, confirm that the RXDSF flag is set to 1 before Synch Break input starts. 2. Before changing LIN operation modes, temporarily stop the LIN operation (LINE bit = 0). 3. Inputs to timer RA and UART0 are prohibited immediately after this bit is set to 1. (Refer to Figure 17.5 Exam ple of Header Field Transm ission Flow chart (1) and Figure 17.9 Exam ple of Header Field Reception Flow chart (2) .) Figure 17.2 LINCR Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 325 of 453 R8C/26 Group, R8C/27 Group 17. Hardware LIN LIN Status Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol LINST Bit Symbol SFDCT SBDCT BCDCT B0CLR B1CLR B2CLR -- (b7-b6) Figure 17.3 Address 0107h Bit Name Synch Field measurementcompleted flag After Reset 00h Function 1 show s Synch Field measurement completed. Synch Break detection flag 1 show s Synch Break detected or Synch Break generation completed. Bus collision detection flag 1 show s Bus collision detected. SFDCT bit clear bit When this bit is set to 1, the SFDCT bit is set to 0. When read, the content is 0. RW SBDCT bit clear bit When this bit is set to 1, the SBDCT bit is set to 0. When read, the content is 0. RW BCDCT bit clear bit When this bit is set to 1, the BCDCT bit is set to 0. When read, the content is 0. RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. LINST Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 326 of 453 RW RO RO RO -- R8C/26 Group, R8C/27 Group 17.4 17. Hardware LIN Functional Description 17.4.1 Master Mode Figure 17.4 shows typical operation of the hardware LIN when transmitting a header field in master mode. Figures 17.5 and 17.6 show an Example of Header Field Transmission Flowchart. When transmitting a header field, the hardware LIN operates as described below. (1) When the TSTART bit in the TRACR register for timer RA is set by writing 1 in software, the hardware LIN outputs "L" level from the TXD0 pin for the period that is set in registers TRAPRE and TRA for timer RA. (2) When timer RA underflows upon reaching the terminal count, the hardware LIN reverses the output of the TXD0 pin and sets the SBDCT flag in the LINST register to 1. Furthermore, if the SBIE bit in the LINCR register is set to 1, it generates a timer RA interrupt. (3) The hardware LIN transmits 55h via UART0. (4) The hardware LIN transmits an ID field via UART0 after it finishes sending 55h. (5) The hardware LIN performs communication for a response field after it finishes sending the ID field. Synch Break TXD0 pin SBDCT flag in the LINST register IR bit in the TRAIC register Synch Field 1 0 Set by writing 1 to the B1CLR bit in the LINST register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program 1 0 (1) (2) (3) Shown above is the case where LINE = 1, MST = 1, SBIE = 1 Figure 17.4 IDENTIFIER Typical Operation when Sending a Header Field Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 327 of 453 (4) (5) R8C/26 Group, R8C/27 Group 17. Hardware LIN Timer RA Set to timer mode Bits TMOD0 to TMOD2 in TRAMR register 000b Timer RA Set the pulse output level from low to start TEDGSEL bit in TRAIOC register 1 Timer RA Set the INT1/TRAIO pin to P1_5 TIOSEL bit in TRAIOC register 1 Timer RA Set the count source (f1, f2, f8, fOCO) Bits TCK0 to TCK2 in TRAMR register Timer RA Set the Synch Break width TRAPRE register TRA register UART0 Set to transmit/receive mode (Transfer data length: 8 bits, Internal clock, 1 stop bit, Parity disabled) U0MR register UART0 Set the BRG count source (f1, f8, f32) Bits CLK0 to CLK2 in U0C0 register UART0 Set the bit rate U0BRG register For the hardware LIN function, set the TIOSEL bit in the TRAIOC register to 1. Set the count source and registers TRA and TRAPRE as suitable for the Synch Break period. Set the BRG count source and U0BRG register as appropriate for the bit rate. Hardware LIN Set the LIN operation to stop LINCR register LINE bit 0 Hardware LIN Set to master mode MST bit in LINCR register 1 Hardware LIN Set the LIN operation to start LINE bit in LINCR register 1 Hardware LIN Set the register to enable interrupts (Bus collision detection, Synch Break detection, Synch Field measurement) Bits BCIE, SBIE, SFIE in LINCR register Hardware LIN Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in LINST register 1 A Figure 17.5 Example of Header Field Transmission Flowchart (1) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 328 of 453 During master mode, the Synch Field measurementcompleted interrupt cannot be used. R8C/26 Group, R8C/27 Group 17. Hardware LIN A Timer RA Set the timer to start counting TSTART bit in TRACR register 1 Timer RA Read the count status flag TCSTF flag in TRACR register TCSTF = 1 ? NO YES Hardware LIN Read the Synch Break detection flag SBDCT flag in LINST register SBDCT = 1 ? NO YES Timer RA Set the timer to stop counting TSTART bit in TRACR register 0 Timer RA Read the count status flag TCSTF flag in TRACR register TCSTF = 0 ? NO YES UART0 Communication via UART0 TE bit in U0C1 register 1 U0TB register 0055h UART0 Communication via UART0 U0TB register ID field Figure 17.6 Timer RA generates Synch Break. If registers TRAPRE and TRA for timer RA do not need to be read or the register settings do not need to be changed after writing 1 to the TSTART bit, the procedure for reading TCSTF flag = 1 can be omitted. Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. The timer RA interrupt may be used to terminate generation of Synch Break. One to two cycles of the CPU clock are required after Synch Break generation completes before the SBDCT flag is set to 1. After timer RA Synch Break is generated, the timer should be made to stop counting. If registers TRAPRE and TRA for timer RA do not need to be read or the register settings do not need to be changed after writing 0 to the TSTART bit, the procedure for reading TCSTF flag = 0 can be omitted. Zero to one cycle of the timer RA count source is required after timer RA stops counting before the TCSTF flag is set to 0. Transmit the Synch Field. Transmit the ID field. Example of Header Field Transmission Flowchart (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 329 of 453 R8C/26 Group, R8C/27 Group 17.4.2 17. Hardware LIN Slave Mode Figure 17.7 shows typical operation of the hardware LIN when receiving a header field in slave mode. Figure 17.8 through Figure 17.10 show an Example of Header Field Transmission Flowchart. When receiving a header field, the hardware LIN operates as described below. (1) Synch Break detection is enabled by writing 1 to the LSTART bit in the LINCR register of the hardware LIN. (2) When "L" level is input for a duration equal to or greater than the period set in timer RA, the hardware LIN detects it as Synch Break. At this time, the SBDCT flag in the LINST register is set to 1. Furthermore, if the SBIE bit in the LINCR register is set to 1, the hardware LIN generates a timer RA interrupt. Then it goes to Synch Field measurement. (3) The hardware LIN receives a Synch Field (55h). At this time, it measures the period of the start bit and bits 0 to 6 by using timer RA. In this case, it is possible to select whether to input the Synch Field signal to RXD0 of UART0 by setting the SBE bit in the LINCR register accordingly. (4) The hardware LIN sets the SFDCT flag in the LINST register to 1 when it finishes measuring the Synch Field. Furthermore, if the SFIE bit in the LINCR register is set to 1, it generates a timer RA interrupt. (5) After it finishes measuring the Synch Field, calculate a transfer rate from the count value of timer RA and set to UART0 and registers TRAPRE and TRA of timer RA again. Then it receives an ID field via UART0. (6) The hardware LIN performs communication for a response field after it finishes receiving the ID field. Synch Break RXD0 pin 1 0 RXD0 input for UART0 1 0 RXDSF flag in the LINCR register SBDCT flag in the LINST register Synch Field IDENTIFIER Set by writing 1 to the LSTART bit in the LINCR register 1 0 Cleared to 0 when Synch Field measurement finishes Set by writing 1 to the B1CLR bit in the LINST register 1 0 Measure this period SFDCT flag in the LINST register 1 0 IR bit in the TRAIC register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program (1) (2) (3) (4) Shown above is the case where LINE = 1, MST = 0, SBE = 1, SBIE = 1, SFIE = 1 Figure 17.7 Typical Operation when Receiving a Header Field Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Set by writing 1 to the B0CLR bit in the LINST register Page 330 of 453 (5) (6) R8C/26 Group, R8C/27 Group 17. Hardware LIN Timer RA Set to pulse width measurement mode Bits TMOD0 to TMOD2 in the TRAMR register 011b Timer RA Set the pulse width measurement level low TEDGSEL bit in the TRAIOC register 0 Timer RA Set the INT1/TRAIO pin to P1_5 TIOSEL bit in the TRAIOC register 1 For the hardware LIN function, set the TIOSEL bit in the TRAIOC register to 1. Timer RA Set the count source (f1, f2, f8, fOCO) Bits TCK0 to TCK2 in the TRAMR register Timer RA Set the Synch Break width TRAPRE register TRA register Set the count source and registers TRA and TRAPRE as appropriate for the Synch Break period. Hardware LIN Set the LIN operation to stop LINE bit in the LINCR register 0 Hardware LIN Set to slave mode MST bit in the LINCR register 0 Hardware LIN Set the LIN operation to start LINE bit in the LINCR register 1 Hardware LIN Set the RXD0 input unmasking timing (After Synch Break detection, or after Synch Field measurement) SBE bit in the LINCR register Hardware LIN Set the register to enable interrupts (Bus collision detection, Synch Break detection, Synch Field measurement) Bits BCIE, SBIE, SFIE in the LINCR register A Figure 17.8 Example of Header Field Reception Flowchart (1) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 331 of 453 Select the timing at which to unmask the RXD0 input for UART0. If the RXD0 input is chosen to be unmasked after detection of Synch Break, the Synch Field signal is also input to UART0. R8C/26 Group, R8C/27 Group 17. Hardware LIN A Hardware LIN Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in the LINST register 1 Timer RA Set to start a pulse width measurement TSTART bit in the TRACR register 1 Timer RA waits until the timer starts counting. Timer RA Read the count status flag TCSTF flag in the TRACR register TCSTF = 1 ? NO YES Hardware LIN Set to start Synch Break detection LSTART bit in the LINCR register 1 Hardware LIN Read the RXD0 input status flag RXDSF flag in the LINCR register RXDSF = 1 ? NO YES Hardware LIN Read the Synch Break detection flag SBDCT flag in the LINST register SBDCT = 1 ? NO YES B Figure 17.9 Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. Hardware LIN waits until the RXD0 input for UART0 is masked. Do not apply "L" level to the RXD pin until the RXDSF flag reads 1 after writing 1 to the LSTART bit. This is because the signal applied during this time is input directly to UART0. One to two cycles of the CPU clock and zero to one cycle of the timer RA count source are required after the LSTART bit is set to 1 before the RXDSF flag is set to 1. After this, input to timer RA and UART0 is enabled. Hardware LIN detects a Synch Break. The interrupt of the timer RA may be used. When Synch Break is detected, timer RA is reloaded with the initially set count value. Even if the duration of the input "L" level is shorter than the set period, timer RA is reloaded with the initially set count value and waits until the next "L" level is input. One to two cycles of the CPU clock are required after Synch Break detection before the SBDCT flag is set to 1. When the SBE bit in the LINCR register is set to 0 (unmasked after Synch Break is detected), timer RA can be used in timer mode after the SBDCT flag in the LINST register is set to 1 and the RXDSF flag is set to 0. Example of Header Field Reception Flowchart (2) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 332 of 453 R8C/26 Group, R8C/27 Group 17. Hardware LIN B YES Hardware LIN Read the Synch Field measurementcompleted flag SFDCT flag in the LINST register SFDCT = 1 ? NO YES UART0 Set the UART0 communication rate U0BRG register Timer RA Set the Synch Break width again TRAPRE register TRA register UART0 Communication via UART0 Clock asynchronous serial interface (UART) mode Transmit ID field Figure 17.10 Example of Header Field Reception Flowchart (3) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 333 of 453 Hardware LIN measures the Synch Field. The interrupt of timer RA may be used (the SBDCT flag is set when the timer RA counter underflows upon reaching the terminal count). When the SBE bit in the LINCR register is set to 1 (unmasked after Synch Field measurement is completed), timer RA may be used in timer mode after the SFDCT bit in the LINST register is set to 1. Set a communication rate based on the Synch Field measurement result. Communication via UART0 (The SBDCT flag is set when the timer RA counter underflows upon reaching the terminal count.) R8C/26 Group, R8C/27 Group 17.4.3 17. Hardware LIN Bus Collision Detection Function The bus collision detection function can be used when UART0 is enabled for transmission (TE bit in the U0C1 register = 1). Figure 17.11 shows the Typical Operation when a Bus Collision is Detected. TXD0 pin 1 0 RXD0 pin 1 0 Transfer clock 1 0 LINE bit in the LINCR register 1 0 TE bit in the U0C1 register 1 0 Set to 1 by a program Set to 1 by a program BCDCT flag in the LINST register IR bit in the TRAIC register Figure 17.11 Set by writing 1 to the B2CLR bit in the LINST register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program 1 0 Typical Operation when a Bus Collision is Detected Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 334 of 453 R8C/26 Group, R8C/27 Group 17.4.4 17. Hardware LIN Hardware LIN End Processing Figure 17.12 shows an Example of Hardware LIN Communication Completion Flowchart. Use the following timing for hardware LIN end processing: * If the hardware bus collision detection function is used Perform hardware LIN end processing after checksum transmission completes. * If the bus collision detection function is not used Perform hardware LIN end processing after header field transmission and reception complete. Timer RA Timer RA Set the timer to stop counting TSTART bit in TRACR register 0 Read the count status flag TCSTF flag in TRACR register TCSTF = 0 ? NO YES UART0 Complete transmission via UART0 Hardware LIN Hardware LIN Figure 17.12 Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in the LINST register 0 Set the timer to stop counting. Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. When the bus collision detection function is not used, end processing for the UART0 transmission is not required. After clearing hardware LIN status flag, stop the hardware LIN operation. Set the LIN operation to stop LINE bit in the LINCR register 0 Example of Hardware LIN Communication Completion Flowchart Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 335 of 453 R8C/26 Group, R8C/27 Group 17.5 17. Hardware LIN Interrupt Requests There are four interrupt requests that are generated by the hardware LIN: Synch Break detection, Synch Break generation completed, Synch Field measurement completed, and bus collision detection. These interrupts are shared with timer RA. Table 17.2 lists the Interrupt Requests of Hardware LIN. Table 17.2 Interrupt Requests of Hardware LIN Interrupt Request Synch Break detection Status Flag Cause of Interrupt SBDCT Generated when timer RA has underflowed after measuring the "L" level duration of RXD0 input, or when a "L" level is input for a duration longer than the Synch Break period during communication. Synch Break generation completed Generated when "L" level output to TXD0 for the duration set by timer RA completes. Synch Field measurement completed SFDCT Generated when measurement for 6 bits of the Synch Field by timer RA is completed. Bus collision detection BCDCT Generated when the RXD0 input and TXD0 output values differed at data latch timing while UART0 is enabled for transmission. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 336 of 453 R8C/26 Group, R8C/27 Group 17.6 17. Hardware LIN Notes on Hardware LIN For the time-out processing of the header and response fields, use another timer to measure the duration of time with a Synch Break detection interrupt as the starting point. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 337 of 453 R8C/26 Group, R8C/27 Group 18. A/D Converter 18. A/D Converter The A/D converter consists of one 10-bit successive approximation A/D converter circuit with a capacitive coupling amplifier. The analog input shares pins P0_0 to P0_7, and P1_0 to P1_3. Therefore, when using these pins, ensure that the corresponding port direction bits are set to 0 (input mode). When not using the A/D converter, set the VCUT bit in the ADCON1 register to 0 (Vref unconnected) so that no current will flow from the VREF pin into the resistor ladder. This helps to reduce the power consumption of the chip. The result of A/D conversion is stored in the AD register. Table 18.1 lists the Performance of A/D converter. Figure 18.1 shows a Block Diagram of A/D Converter. Figures 18.2 and 18.3 show the A/D converter-related registers. Table 18.1 Performance of A/D converter Item A/D conversion method Performance Successive approximation (with capacitive coupling amplifier) 0 V to AVCC Analog input voltage(1) 4.2 V AVCC 5.5 V f1, f2, f4, fOCO-F 2.2 V AVCC < 4.2 V f2, f4, fOCO-F (N, D version) 2.7 V AVCC < 4.2 V f2, f4, fOCO-F (J, K version) 8 bits or 10 bits selectable AVCC = Vref = 5 V, AD = 10 MHz * 8-bit resolution 2 LSB * 10-bit resolution 3 LSB AVCC = Vref = 3.3 V, AD = 10 MHz * 8-bit resolution 2 LSB * 10-bit resolution 5 LSB AVCC = Vref = 2.2 V, AD = 5 MHz * 8-bit resolution 2 LSB * 10-bit resolution 5 LSB Operating clock AD(2) Resolution Absolute accuracy Operating mode Analog input pin A/D conversion start condition Conversion rate per pin One-shot and repeat(3) 12 pins (AN0 to AN11) Software trigger Set the ADST bit in the ADCON0 register to 1 (A/D conversion starts) * Without sample and hold function 8-bit resolution: 49AD cycles, 10-bit resolution: 59AD cycles * With sample and hold function 8-bit resolution: 28AD cycles, 10-bit resolution: 33AD cycles NOTES: 1. The analog input voltage does not depend on use of a sample and hold function. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in 8-bit mode. 2. When 2.7 V AVCC 5.5 V, the frequency of AD must be 10 MHz or below. When 2.2 V AVCC < 2.7 V, the frequency of AD must be 5 MHz or below. Without a sample and hold function, the AD frequency should be 250 kHz or above. With a sample and hold function, the AD frequency should be 1 MHz or above. 3. In repeat mode, only 8-bit mode can be used. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 338 of 453 R8C/26 Group, R8C/27 Group 18. A/D Converter fOCO-F f1 CKS0 = 1 A/D conversion rate selection CKS1 = 1 CKS0 = 0 CKS0 = 1 AD f2 CKS1 = 0 f4 CKS0 = 0 VCUT = 0 AVSS VCUT = 1 VREF Resistor ladder Successive conversion register ADCON0 Vcom AD register Decoder Comparator VIN Data bus P0_7/AN0 P0_6/AN1 P0_5/AN2 P0_4/AN3 P0_3/AN4 P0_2/AN5 P0_1/AN6 P0_0/AN7 P1_0/AN8 P1_1/AN9 P1_2/AN10 P1_3/AN11 CH2 to CH0 = 000b CH2 to CH0 = 001b CH2 to CH0 = 010b CH2 to CH0 = 011b CH2 to CH0 = 100b CH2 to CH0 = 101b CH2 to CH0 = 110b CH2 to CH0 = 111b ADGSEL0 = 0 CH2 to CH0 = 100b CH2 to CH0 = 101b CH2 to CH0 = 110b CH2 to CH0 = 111b CH0 to CH2, ADGSEL0, CKS0: Bits in ADCON0 register CKS1, VCUT: Bits in ADCON1 register Figure 18.1 Block Diagram of A/D Converter Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 339 of 453 ADGSEL0 = 1 R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW A/D operating mode select 0 : One-shot mode bit(2) 1 : Repeat mode (4) ADGSEL0 -- (b5) ADST 0 : Selects port P0 group (AN0 to AN7) 1 : Selects port P1 group (AN8 to AN11) Reserved bit Set to 0. A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Select fOCO-F RW NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. When changing A/D operation mode, set the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. ADGSEL0 = 0 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 ADGSEL0 = 1 Do not set. ADCON0 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW A/D input group select bit CKS0 Figure 18.2 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 340 of 453 AN8 AN9 AN10 AN11 RW RW R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name -- Reserved bits (b2-b0) BITS CKS1 VCUT -- (b6-b7) After Reset 00h Function RW Set to 0. RW 8/10-bit mode select bit(2) 0 : 8-bit mode 1 : 10-bit mode RW Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. RW VREF connect bit(3) 0 : VREF not connected 1 : VREF connected RW Reserved bits Set to 0. RW NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. Set the BITS bit to 0 (8-bit mode) in repeat mode. 3. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. A/D Control Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol ADCON2 Bit Symbol Address 00D4h Bit Name A/D conversion method select bit After Reset 00h Function 0 : Without sample and hold 1 : With sample and hold -- (b3-b1) Reserved bits Set to 0. -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. SMP RW RW RW -- NOTE: 1. If the ADCON2 register is rew ritten during A/D conversion, the conversion result is undefined. A/D Register (b15) b7 (b8) b0 b7 b0 Symbol AD Address 00C1h-00C0h After Reset Undefined Function When BITS bit in ADCON1 register is set to 1 (10-bit mode). 8 low -order bits in A/D conversion result 2 high-order bits in A/D conversion result Nothing is assigned. If necessary, set to 0. When read, the content is 0. Figure 18.3 Registers ADCON1, ADCON2, and AD Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 341 of 453 When BITS bit in ADCON1 register is set to 0 (8-bit mode). A/D conversion result When read, the content is undefined. RW RO RO -- R8C/26 Group, R8C/27 Group 18.1 18. A/D Converter One-Shot Mode In one-shot mode, the input voltage of one selected pin is A/D converted once. Table 18.2 lists the Specifications of One-Shot Mode. Figure 18.4 shows the ADCON0 Register in One-Shot Mode and Figure 18.5 shows the ADCON1 Register in One-Shot Mode. Table 18.2 Specifications of One-Shot Mode Item Function Start condition Stop condition Specification The input voltage of one pin selected by bits CH2 to CH0 and ADGSEL0 is A/D converted once Set the ADST bit to 1 (A/D conversion starts) * A/D conversion completes (ADST bit is set to 0) * Set the ADST bit to 0 A/D conversion completes Interrupt request generation timing Input pin Select one of AN0 to AN11 Reading of A/D conversion Read AD register result Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 342 of 453 R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW A/D operating mode select 0 : One-shot mode bit(2) (4) ADGSEL0 -- (b5) ADST 0 : Selects port P0 group (AN0 to AN7) 1 : Selects port P1 group (AN8 to AN11) Reserved bit Set to 0. A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Select fOCO-F RW NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. After changing the A/D operating mode, select the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. ADGSEL0 = 0 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 ADGSEL0 = 1 Do not set. AN8 AN9 AN10 AN11 ADCON0 Register in One-Shot Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW A/D input group select bit CKS0 Figure 18.4 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 343 of 453 RW RW R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name -- Reserved bits (b2-b0) BITS CKS1 -- (b6-b7) Set to 0. RW Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. RW VREF connect bit 1 : VREF connected Reserved bits Set to 0. ADCON1 Register in One-Shot Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW 0 : 8-bit mode 1 : 10-bit mode NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. Figure 18.5 RW 8/10-bit mode select bit (2) VCUT After Reset 00h Function Page 344 of 453 RW RW R8C/26 Group, R8C/27 Group 18.2 18. A/D Converter Repeat Mode In repeat mode, the input voltage of one selected pin is A/D converted repeatedly. Table 18.3 lists the Specifications of Repeat Mode. Figure 18.6 shows the ADCON0 Register in Repeat Mode and Figure 18.7 shows the ADCON1 Register in Repeat Mode. Table 18.3 Specifications of Repeat Mode Item Function Start conditions Stop condition Interrupt request generation timing Input pin Reading of result of A/D converter Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Specification The Input voltage of one pin selected by bits CH2 to CH0 and ADGSEL0 is A/D converted repeatedly Set the ADST bit to 1 (A/D conversion starts) Set the ADST bit to 0 Not generated Select one of AN0 to AN11 Read AD register Page 345 of 453 R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 1 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW ADGSEL0 -- (b5) ADST A/D operating mode select 1 : Repeat mode bit(2) RW A/D input group select bit(4) 0 : Selects port P0 group (AN0 to AN7) 1 : Selects port P1 group (AN8 to AN11) RW Reserved bit Set to 0. A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Do not set. RW CKS0 NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. After changing A/D operation mode, select the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. Figure 18.6 ADGSEL0 = 0 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 ADGSEL0 = 1 Do not set. AN8 AN9 AN10 AN11 ADCON0 Register in Repeat Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 346 of 453 RW R8C/26 Group, R8C/27 Group 18. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 0 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name Reserved bits -- (b2-b0) BITS CKS1 VCUT -- (b6-b7) After Reset 00h Function Set to 0. 8/10-bit mode select bit(2) 0 : 8-bit mode Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. VREF connect bit(3) 1 : VREF connected Reserved bits Set to 0. NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. Set the BITS bit to 0 (8-bit mode) in repeat mode. 3. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. Figure 18.7 ADCON1 Register in Repeat Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 347 of 453 RW RW RW RW RW RW R8C/26 Group, R8C/27 Group 18.3 18. A/D Converter Sample and Hold When the SMP bit in the ADCON2 register is set to 1 (sample and hold function enabled), the A/D conversion rate per pin increases. The sample and hold function is available in all operating modes. Start A/D conversion after selecting whether the sample and hold circuit is to be used or not. Figure 18.8 shows a Timing Diagram of A/D Conversion. Sample and hold disabled Conversion time of 1st bit Sampling time 4o AD cycles 2nd bit Comparison Sampling time Comparison Sampling time Comparison 2.5o AD cycles 2.5o AD cycles time time time * Repeat until conversion ends Sample and hold enabled 2nd bit Conversion time of 1st bit Sampling time 4o AD cycles Comparison time Comparison Comparison Comparison time time time * Repeat until conversion ends Figure 18.8 18.4 Timing Diagram of A/D Conversion A/D Conversion Cycles Figure 18.9 shows the A/D Conversion Cycles. Conversion time at the 1st bit A/D Conversion Mode Conversion Time Sampling Time Comparison Time Conversion time at the 2nd bit and the follows Sampling Time End process Comparison End process Time Without Sample & Hold 8 bits 49AD 4AD 2.0AD 2.5AD 2.5AD 8.0AD Without Sample & Hold 10 bits 59AD 4AD 2.0AD 2.5AD 2.5AD 8.0AD With Sample & Hold 8 bits 28AD 4AD 2.5AD 0.0AD 2.5AD 4.0AD With Sample & Hold 10 bits 33AD 4AD 2.5AD 0.0AD 2.5AD 4.0AD Figure 18.9 A/D Conversion Cycles Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 348 of 453 R8C/26 Group, R8C/27 Group 18.5 18. A/D Converter Internal Equivalent Circuit of Analog Input Figure 18.10 shows the Internal Equivalent Circuit of Analog Input. VCC VCC VSS AVCC ON Resistor Approx. 2k Wiring Resistor Approx. 0.2k Parasitic Diode AN0 SW1 ON Resistor Approx. 0.6k Analog Input Voltage SW2 Parasitic Diode i Ladder-type Switches i=12 AMP VIN ON Resistor Approx. 5k Sampling Control Signal VSS C = Approx.1.5pF SW3 SW4 i Ladder-type Wiring Resistors AVSS ON Resistor Approx. 2k Wiring Resistor Approx. 0.2k Chopper-type Amplifier AN11 SW1 b4 b2 b1 b0 A/D Control Register 0 Reference Control Signal A/D Successive Conversion Register Vref VREF Resistor ladder SW5 Comparison voltage ON Resistor Approx. 0.6k f A/D Conversion Interrupt Request AVSS Comparison reference voltage (Vref) generator Sampling Comparison SW1 conducts only on the ports selected for analog input. Connect to SW2 and SW3 are open when A/D conversion is not in progress; their status varies as shown by the waveforms in the diagrams on the left. Control signal for SW2 Connect to SW4 conducts only when A/D conversion is not in progress. Connect to Control signal for SW3 Connect to SW5 conducts when compare operation is in progress. NOTE: 1. Use only as a standard for designing this data. Mass production may cause some changes in device characteristics. Figure 18.10 Internal Equivalent Circuit of Analog Input Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 349 of 453 R8C/26 Group, R8C/27 Group 18.6 18. A/D Converter Output Impedance of Sensor under A/D Conversion To carry out A/D conversion properly, charging the internal capacitor C shown in Figure 18.11 has to be completed within a specified period of time. T (sampling time) as the specified time. Let output impedance of sensor equivalent circuit be R0, internal resistance of microcomputer be R, precision (error) of the A/D converter be X, and the resolution of A/D converter be Y (Y is 1024 in the 10-bit mode, and 256 in the 8-bit mode). VC is generally And when t = T, 1 - -------------------------C ( R0 + R ) VC = VIN 1 - e t X X VC = VIN - ---- VIN = VIN 1 - ---- Y Y 1 - --------------------------T C ( R0 + R) = X e ---Y 1 - -------------------------T = ln X ---C ( R0 + R ) Y Hence, T R0 = - ------------------- - R X C * ln ---Y Figure 18.11 shows the Analog Input Pin and External Sensor Equivalent Circuit. When the difference between VIN and VC becomes 0.1LSB, we find impedance R0 when voltage between pins VC changes from 0 to VIN(0.1/1024) VIN in time T. (0.1/1024) means that A/D precision drop due to insufficient capacitor charge is held to 0.1LSB at time of A/D conversion in the 10-bit mode. Actual error however is the value of absolute precision added to 0.1LSB. When f(XIN) = 10 MHz, T = 0.25 s in the A/D conversion mode without sample and hold. Output impedance R0 for sufficiently charging capacitor C within time T is determined as follows. T = 0.25 s, R = 2.8 k, C = 6.0 pF, X = 0.1, and Y = 1024. Hence, 3 3 0.25 x 10 - 6 - - 2.8 x10 1.7 x10 R0 = - -------------------------------------------------0.1 6.0 x 10 - 12 * ln ----------1024 Thus, the allowable output impedance of the sensor equivalent circuit, making the precision (error) 0.1LSB or less, is approximately 1.7 k. maximum. MCU Sensor equivalent circuit R0 R (2.8 k) VIN C (6.0 pF) VC NOTE: 1. The capacity of the terminal is assumed to be 4.5 pF. Figure 18.11 Analog Input Pin and External Sensor Equivalent Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 350 of 453 R8C/26 Group, R8C/27 Group 18.7 18. A/D Converter Notes on A/D Converter * Write to each bit (other than bit 6) in the ADCON0 register, each bit in the ADCON1 register, or the SMP bit in the ADCON2 register when A/D conversion is stopped (before a trigger occurs). When the VCUT bit in the ADCON1 register is changed from 0 (VREF not connected) to 1 (VREF connected), wait for at least 1 s before starting the A/D conversion. * After changing the A/D operating mode, select an analog input pin again. * When using the one-shot mode, ensure that A/D conversion is completed before reading the AD register. The IR bit in the ADIC register or the ADST bit in the ADCON0 register can be used to determine whether A/D conversion is completed. * When using the repeat mode, select the frequency of the A/D converter operating clock AD or more for the CPU clock during A/D conversion. * If the ADST bit in the ADCON0 register is set to 0 (A/D conversion stops) by a program and A/D conversion is forcibly terminated during an A/D conversion operation, the conversion result of the A/D converter will be undefined. If the ADST bit is set to 0 by a program, do not use the value of the AD register. * Connect 0.1 F capacitor between the P4_2/VREF pin and AVSS pin. * Do not enter stop mode during A/D conversion. * Do not enter wait mode when the CM02 bit in the CM0 register is set to 1 (peripheral function clock stops in wait mode) during A/D conversion. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 351 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory 19. Flash Memory 19.1 Overview In the flash memory, rewrite operations to the flash memory can be performed in three modes: CPU rewrite, standard serial I/O, and parallel I/O. Table 19.1 lists the Flash Memory Performance (refer to Tables 1.1 and 1.2 Functions and Specifications for items not listed in Table 19.1). Table 19.1 Flash Memory Performance Item Flash memory operating mode Division of erase block Programming method Erase method Programming and erasure control method(3) Rewrite control method Specification 3 modes (CPU rewrite, standard serial I/O, and parallel I/O) Refer to Figures 19.1 and 19.2 Byte unit Block erase Program and erase control by software command Rewrite control for blocks 0 and 1 by FMR02 bit in FMR0 register Rewrite control for block 0 by FMR15 bit and block 1 by FMR16 bit in FMR1 register Number of commands 5 commands Programming and Blocks 0 and 1 (program R8C/26 Group: 100 times; R8C/27 Group: 1,000 times ROM) erasure endurance(1) Blocks A and B (data 10,000 times flash)(2) ID code check function Standard serial I/O mode supported ROM code protect Parallel I/O mode supported NOTES: 1. Definition of programming and erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 100 or 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to different addresses in block A, a 1-Kbyte block, and then the block is erased, the programming/ erasure endurance still stands at one. When performing 100 or more rewrites, the actual erase count can be reduced by executing programming operations in such a way that all blank areas are used before performing an erase operation. Avoid rewriting only particular blocks and try to average out the programming and erasure endurance of the blocks. It is also advisable to retain data on the erasure endurance of each block and limit the number of erase operations to a certain number. 2. Blocks A and B are implemented only in the R8C/27 group. 3. To perform programming and erasure, use VCC = 2.7 to 5.5 V as the supply voltage. Do not perform programming and erasure at less than 2.7 V. Table 19.2 Flash Memory Rewrite Modes Flash memory Rewrite mode Function Standard Serial I/O Mode User ROM area is rewritten by executing User ROM area is rewritten by a software commands from the CPU. dedicated serial EW0 mode: Rewritable in the RAM EW1 mode: Rewritable in flash memory programmer. User ROM area User ROM area CPU Rewrite Mode Areas which can be rewritten Operating mode Single chip mode ROM Programmer None Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 352 of 453 Boot mode Serial programmer Parallel I/O Mode User ROM area is rewritten by a dedicated parallel programmer. User ROM area Parallel I/O mode Parallel programmer R8C/26 Group, R8C/27 Group 19.2 19. Flash Memory Memory Map The flash memory contains a user ROM area and a boot ROM area (reserved area). Figure 19.1 shows the Flash Memory Block Diagram for R8C/26 Group. Figure 19.2 shows a Flash Memory Block Diagram for R8C/27 Group. The user ROM area of the R8C/27 Group contains an area (program ROM) which stores MCU operating programs and blocks A and B (data flash) each 1 Kbyte in size. The user ROM area is divided into several blocks. The user ROM area can be rewritten in CPU rewrite mode and standard serial I/O and parallel I/O modes. When rewriting blocks 0 and 1 in CPU rewrite mode, set the FMR02 bit in the FMR0 register to 1 (rewrite enabled). When the FMR15 bit in the FMR1 register is set to 0 (rewrite enabled), block 0 is rewritable. When the FMR16 bit is set to 0 (rewrite enabled), block 1 is rewritable. The rewrite control program for standard serial I/O mode is stored in the boot ROM area before shipment. The boot ROM area and the user ROM area share the same address, but have separate memory areas. 16 Kbytes ROM product 0C000h Block 0: 16 Kbytes(1) 0FFFFh 8 Kbytes ROM product 0E000h Program ROM Block 0: 8 Kbytes(1) 0FFFFh User ROM area User ROM area 32 Kbytes ROM product 08000h Block 1: 16 Kbytes(1) 0BFFFh 0C000h 24 Kbytes ROM product 0A000h Program ROM Block 1: 8 Kbytes(1) 0BFFFh 0C000h Block 0: 16 Kbytes(1) Block 0: 16 Kbytes(1) User ROM area 0E000h 8 Kbytes 0FFFFh 0FFFFh 0FFFFh User ROM area Boot ROM area (reserved area)(2) NOTES: 1. When the FMR02 bit in the FMR0 register is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 0 (rewrite enabled), block 0 is rewritable. When the FMR16 bit is set to 0 (rewrite enabled), block 1 is rewritable (only for CPU rewrite mode). 2. This area is for storing the boot program provided by Renesas Technology. Figure 19.1 Flash Memory Block Diagram for R8C/26 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 353 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory 16 Kbytes ROM product 02400h Block A: 1 Kbyte 8 Kbytes ROM product 02400h Block A: 1 Kbyte Data flash Block B: 1 Kbyte 02BFFh 02BFFh Block B: 1 Kbyte 0C000h Block 0: 16 Kbytes(1) 0E000h 0FFFFh Program ROM Block 0: 8 Kbytes(1) 0FFFFh User ROM area User ROM area 24 Kbytes ROM product 32 Kbytes ROM product 02400h Block A: 1 Kbyte 02400h Block A: 1 Kbyte Data flash 02BFFh Block B: 1 Kbyte 02BFFh Block B: 1 Kbyte 08000h Block 1: 16 Kbytes(1) 0BFFFh 0C000h Program ROM 0A000h Block 1: 8 Kbytes(1) 0BFFFh 0C000h Block 0: 16 Kbytes(1) 0FFFFh Block 0: 16 Kbytes(1) 0FFFFh User ROM area 0E000h 8 Kbytes 0FFFFh User ROM area Boot ROM area (reserved area)(2) NOTES: 1. When the FMR02 bit in the FMR0 register is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 0 (rewrite enabled), block 0 is rewritable. When the FMR16 bit is set to 0 (rewrite enabled), block 1 is rewritable (only for CPU rewrite mode). 2. This area is for storing the boot program provided by Renesas Technology. Figure 19.2 Flash Memory Block Diagram for R8C/27 Group Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 354 of 453 R8C/26 Group, R8C/27 Group 19.3 19. Flash Memory Functions to Prevent Rewriting of Flash Memory Standard serial I/O mode has an ID code check function, and parallel I/O mode has a ROM code protect function to prevent the flash memory from being read or rewritten easily. 19.3.1 ID Code Check Function This function is used in standard serial I/O mode. Unless the flash memory is blank, the ID codes sent from the programmer and the ID codes written in the flash memory are checked to see if they match. If the ID codes do not match, the commands sent from the programmer are not acknowledged. The ID codes consist of 8 bits of data each, the areas of which, beginning with the first byte, are 00FFDFh, 00FFE3h, 00FFEBh, 00FFEFh, 00FFF3h, 00FFF7h, and 00FFFBh. Write programs in which the ID codes are set at these addresses and write them to the flash memory. Address 00FFDFh to 00FFDCh ID1 Undefined instruction vector 00FFE3h to 00FFE0h ID2 Overflow vector BRK instruction vector 00FFE7h to 00FFE4h 00FFEBh to 00FFE8h ID3 Address match vector 00FFEFh to 00FFECh ID4 Single step vector 00FFF3h to 00FFF0h ID5 00FFF7h to 00FFF4h ID6 00FFFBh to 00FFF8h ID7 00FFFFh to 00FFFCh (Note 1) Oscillation stop detection/watchdog timer/voltage monitor 1 and voltage monitor 2 vector Address break (Reserved) Reset vector 4 bytes NOTE: 1. The OFS register is assigned to 00FFFFh. Refer to Figure 19.4 OFS Register for OFS register details. Figure 19.3 Address for Stored ID Code Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 355 of 453 R8C/26 Group, R8C/27 Group 19.3.2 19. Flash Memory ROM Code Protect Function The ROM code protect function disables reading or changing the contents of the on-chip flash memory by the OFS register in parallel I/O mode. Figure 19.4 shows the OFS Register. The ROM code protect function is enabled by writing 0 to the ROMCP1 bit and 1 to the ROMCR bit. It disables reading or changing the contents of the on-chip flash memory. Once ROM code protect is enabled, the content in the internal flash memory cannot be rewritten in parallel I/O mode. To disable ROM code protect, erase the block including the OFS register with CPU rewrite mode or standard serial I/O mode. Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON LVD1ON Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2, 4) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset RW Voltage detection 1 circuit start bit(5, 6) 0 : Voltage monitor 1 reset enabled after hardw are reset 1 : Voltage monitor 1 reset disabled after hardw are reset RW Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. The LVD0ON bit setting is valid only by a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. 4. For N, D version only. For J, K version, set the LVD0ON bit to 1 (voltage monitor 0 reset disabled after hardw are reset). 5. The LVD1ON bit setting is valid only by a hardw are reset. When the pow er-on reset function is used, set the LVD1ON bit to 0 (voltage monitor 1 reset enabled after hardw are reset). 6. For J, K version only. For N, D version, set the LVD1ON bit to 1 (voltage monitor 1 reset disabled after hardw are reset). Figure 19.4 OFS Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 356 of 453 R8C/26 Group, R8C/27 Group 19.4 19. Flash Memory CPU Rewrite Mode In CPU rewrite mode, the user ROM area can be rewritten by executing software commands from the CPU. Therefore, the user ROM area can be rewritten directly while the MCU is mounted on a board without using a ROM programmer. Execute the program and block erase commands only to blocks in the user ROM area. The flash module has an erase-suspend function when an interrupt request is generated during an erase operation in CPU rewrite mode. It performs an interrupt process after the erase operation is halted temporarily. During erasesuspend, the user ROM area can be read by a program. In case an interrupt request is generated during an auto-program operation in CPU rewrite mode, the flash module contains a program-suspend function which performs the interrupt process after the auto-program operation is suspended. During program-suspend, the user ROM area can be read by a program. CPU rewrite mode has an erase write 0 mode (EW0 mode) and an erase write 1 mode (EW1 mode). Table 19.3 lists the Differences between EW0 Mode and EW1 Mode. Table 19.3 Differences between EW0 Mode and EW1 Mode Item Operating mode Areas in which a rewrite control program can be located Areas in which a rewrite control program can be executed Areas which can be rewritten EW0 Mode Single-chip mode User ROM area Necessary to transfer to any area other Executing directly in user ROM or RAM than the flash memory (e.g., RAM) before area possible executing User ROM area User ROM area However, blocks which contain a rewrite control program are excluded(1) None * Program and block erase commands Cannot be run on any block which contains a rewrite control program * Read status register command Cannot be executed Read status register mode Read array mode Software command restrictions Modes after program or erase Modes after read status register CPU status during autowrite and auto-erase Flash memory status detection Read status register mode Do not execute this command Operating Conditions for transition to erase-suspend Conditions for transitions to program-suspend CPU clock EW1 Mode Single-chip mode User ROM area Hold state (I/O ports hold state before the command is executed) * Read bits FMR00, FMR06, and FMR07 Read bits FMR00, FMR06, and FMR07 in in the FMR0 register by a program the FMR0 register by a program * Execute the read status register command and read bits SR7, SR5, and SR4 in the status register. Set bits FMR40 and FMR41 in the FMR4 The FMR40 bit in the FMR4 register is set register to 1 by a program. to 1 and the interrupt request of the enabled maskable interrupt is generated Set bits FMR40 and FMR42 in the FMR4 The FMR40 bit in the FMR4 register is set register to 1 by a program. to 1 and the interrupt request of the enabled maskable interrupt is generated 5 MHz or below No restriction (on clock frequency to be used) NOTE: 1. When the FMR02 bit in the FMR0 register is set to 1 (rewrite enabled), rewriting block 0 is enabled by setting the FMR15 bit in the FMR1 register to 0 (rewrite enabled), and rewriting block 1 is enabled by setting the FMR16 bit to 0 (rewrite enabled). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 357 of 453 R8C/26 Group, R8C/27 Group 19.4.1 19. Flash Memory EW0 Mode The MCU enters CPU rewrite mode and software commands can be acknowledged by setting the FMR01 bit in the FMR0 register to 1 (CPU rewrite mode enabled). In this case, since the FMR11 bit in the FMR1 register is set to 0, EW0 mode is selected. Use software commands to control program and erase operations. The FMR0 register or the status register can be used to determine when program and erase operations complete. During auto-erasure, set the FMR40 bit to 1 (erase-suspend enabled) and the FMR41 bit to 1 (request erasesuspend). Wait for td(SR-SUS) and ensure that the FMR46 bit is set to 1 (read enabled) before accessing the user ROM area. The auto-erase operation can be restarted by setting the FMR41 bit to 0 (erase restarts). To enter program-suspend during the auto-program operation, set the FMR40 bit to 1 (suspend enabled) and the FMR42 bit to 1 (request program-suspend). Wait for td(SR-SUS) and ensure that the FMR46 bit is set to 1 (read enabled) before accessing the user ROM area. The auto-program operation can be restarted by setting the FMR42 bit to 0 (program restarts). 19.4.2 EW1 Mode The MCU is switched to EW1 mode by setting the FMR11 bit to 1 (EW1 mode) after setting the FMR01 bit to 1 (CPU rewrite mode enabled). The FMR0 register can be used to determine when program and erase operations complete. Do not execute commands that use the read status register in EW1 mode. To enable the erase-suspend function during auto-erasure, execute the block erase command after setting the FMR40 bit to 1 (erase-suspend enabled). The interrupt to enter erase-suspend should be in interrupt enabled status. After waiting for td(SR-SUS) after the block erase command is executed, the interrupt request is acknowledged. When an interrupt request is generated, the FMR41 bit is automatically set to 1 (requests erase-suspend) and the auto-erase operation suspends. If an auto-erase operation does not complete (FMR00 bit is 0) after an interrupt process completes, the auto-erase operation restarts by setting the FMR41 bit to 0 (erasure restarts) To enable the program-suspend function during auto-programming, execute the program command after setting the FMR40 bit to 1 (suspend enabled). The interrupt to enter program-suspend should be in interrupt enabled status. After waiting for td(SR-SUS) after the program command is executed, an interrupt request is acknowledged. When an interrupt request is generated, the FMR42 bit is automatically set to 1 (request program-suspend) and the auto-program operation suspends. When the auto-program operation does not complete (FMR00 bit is 0) after the interrupt process completes, the auto-program operation can be restarted by setting the FMR42 bit to 0 (programming restarts). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 358 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Figure 19.5 shows the FMR0 Register, Figure 19.6 shows the FMR1 Register and Figure 19.7 shows the FMR4 Register. 19.4.2.1 FMR00 Bit This bit indicates the operating status of the flash memory. The bits value is 0 during programming, erasure (including suspend periods), or erase-suspend mode; otherwise, it is 1. 19.4.2.2 FMR01 Bit The MCU is made ready to accept commands by setting the FMR01 bit to 1 (CPU rewrite mode). 19.4.2.3 FMR02 Bit Rewriting of block 0 and block 1 does not accept program or block erase commands if the FMR02 bit is set to 0 (rewrite disabled). Rewriting of block 0 and block 1 is controlled by bits FMR15 and FMR16 if the FMR02 bit is set to 1 (rewrite enabled). 19.4.2.4 FMSTP Bit This bit is used to initialize the flash memory control circuits, and also to reduce the amount of current consumed by the flash memory. Access to the flash memory is disabled by setting the FMSTP bit to 1. Therefore, the FMSTP bit must be written to by a program transferred to the RAM. In the following cases, set the FMSTP bit to 1: * When flash memory access resulted in an error while erasing or programming in EW0 mode (FMR00 bit not reset to 1 (ready)) * To provide lower consumption in high-speed on-chip oscillator mode, low-speed on-chip oscillator mode (XIN clock stops), and low-speed clock mode (XIN clock stops). Figure 19.11 shows the Process to Reduce Power Consumption in High-Speed On-Chip Oscillator Mode, LowSpeed On-Chip Oscillator Mode (XIN Clock Stops) and Low-Speed Clock Mode (XIN Clock Stops). Handle according to this flowchart. Note that when going to stop or wait mode while the CPU rewrite mode is disabled, the FMR0 register does not need to be set because the power for the flash memory is automatically turned off and is turned back on again after returning from stop or wait mode. 19.4.2.5 FMR06 Bit This is a read-only bit indicating the status of an auto-program operation. The bit is set to 1 when a program error occurs; otherwise, it is cleared to 0. For details, refer to the description in 19.4.5 Full Status Check. 19.4.2.6 FMR07 Bit This is a read-only bit indicating the status of an auto-erase operation. The bit is set to 1 when an erase error occurs; otherwise, it is set to 0. Refer to 19.4.5 Full Status Check for details. 19.4.2.7 FMR11 Bit Setting this bit to 1 (EW1 mode) places the MCU in EW1 mode. 19.4.2.8 FMR15 Bit When the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit is set to 0 (rewrite enabled), block 0 accepts program and block erase commands. 19.4.2.9 FMR16 Bit When the FMR02 bit is set to 1 (rewrite enabled) and the FMR16 bit is set to 0 (rewrite enabled), block 1 accepts program and block erase commands. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 359 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory 19.4.2.10 FMR40 Bit The suspend function is enabled by setting the FMR40 bit to 1 (enable). 19.4.2.11 FMR41 Bit In EW0 mode, the MCU enters erase-suspend mode when the FMR41 bit is set to 1 by a program. The FMR41 bit is automatically set to 1 (request erase-suspend) when an interrupt request of an enabled interrupt is generated in EW1 mode, and then the MCU enters erase-suspend mode. Set the FMR41 bit to 0 (erase restarts) when the auto-erase operation restarts. 19.4.2.12 FMR42 Bit In EW0 mode, the MCU enters program-suspend mode when the FMR42 bit is set to 1 by a program. The FMR42 bit is automatically set to 1 (request program-suspend) when an interrupt request of an enabled interrupt is generated in EW1 mode, and then the MCU enters program-suspend mode. Set the FMR42 bit to 0 (program restart) when the auto-program operation restarts. 19.4.2.13 FMR43 Bit When the auto-erase operation starts, the FMR43 bit is set to 1 (erase execution in progress). The FMR43 bit remains set to 1 (erase execution in progress) during erase-suspend operation. When the auto-erase operation ends, the FMR43 bit is set to 0 (erase not executed). 19.4.2.14 FMR44 Bit When the auto-program operation starts, the FMR44 bit is set to 1 (program execution in progress). The FMR44 bit remains set to 1 (program execution in progress) during program-suspend operation. When the auto-program operation ends, the FMR44 bit is set to 0 (program not executed). 19.4.2.15 FMR46 Bit The FMR46 bit is set to 0 (reading disabled) during auto-program or auto-erase execution and set to 1 (reading enabled) in suspend mode. Do not access the flash memory while this bit is set to 0. 19.4.2.16 FMR47 Bit Power consumption when reading the flash memory can be reduced by setting the FMR47 bit to 1 (enabled) in low-speed clock mode (XIN clock stops) and low-speed on-chip oscillator mode (XIN clock stops). Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 360 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Flash Memory Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol FMR0 Bit Symbol FMR00 FMR01 FMR02 Address 01B7h ___ Bit Name RY/BY status flag FMR06 FMR07 Function 0 : Busy (w riting or erasing in progress) 1 : Ready RW RO CPU rew rite mode select bit(1) 0 : CPU rew rite mode disabled 1 : CPU rew rite mode enabled RW Block 0, 1 rew rite enable bit(2, 6) 0 : Disables rew rite 1 : Enables rew rite RW Flash memory stop bit(3, 5) 0 : Enables flash memory operation 1 : Stops flash memory (enters low -pow er consumption state and flash memory is reset) RW FMSTP -- (b5-b4) After Reset 00000001b Reserved bits Set to 0. Program status flag(4) 0 : Completed successfully 1 : Terminated by error RO Erase status flag(4) 0 : Completed successfully 1 : Terminated by error RO RW NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. Enter read array mode and set this bit to 0. 2. Set this bit to 1 immediately after setting it first to 0 w hile the FMR01 bit is set to 1. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 3. Set this bit by a program transferred to the RAM. 4. This bit is set to 0 by executing the clear status command. 5. This bit is enabled w hen the FMR01 bit is set to 1 (CPU rew rite mode enabled). When the FMR01 bit is set to 0, w riting 1 to the FMSTP bit causes the FMSTP bit to be set to 1. The flash memory does not enter low -pow er consumption state nor is it reset. 6. When setting the FMR01 bit to 0 (CPU rew rite mode disabled), the FMR02 bit is set to 0 (disables rew rite). Figure 19.5 FMR0 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 361 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Flash Memory Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 0 Symbol Address 01B5h FMR1 Bit Symbol Bit Name -- Reserved bit (b0) After Reset 1000000Xb Function When read, the content is undefined. (1, 2) FMR11 -- (b4-b2) FMR15 FMR16 -- (b7) EW1 mode select bit 0 : EW0 mode 1 : EW1 mode Reserved bits Set to 0. Block 0 rew rite disable bit (2,3) Block 1 rew rite disable bit (2,3) Reserved bit RW RO RW RW 0 : Enables rew rite 1 : Disables rew rite RW 0 : Enables rew rite 1 : Disables rew rite RW Set to 1. RW NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0 w hile the FMR01 bit is set to 1 (CPU rew rite mode enable) . Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 2. This bit is set to 0 by setting the FMR01 bit to 0 (CPU rew rite mode disabled). 3. When the FMR01 bit is set to 1 (CPU rew rite mode enabled), bits FMR15 and FMR16 can be w ritten to. To set this bit to 0, set it to 0 immediately after setting it first to 1. To set this bit to 1, set it to 1. Figure 19.6 FMR1 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 362 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Flash Memory Control Register 4 b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol FMR4 Bit Symbol FMR40 Address 01B3h Bit Name Erase-suspend function enable bit(1) After Reset 01000000b Function RW 0 : Erase restart 1 : Erase-suspend request RW 0 : Program restart 1 : Program-suspend request RW Erase command flag 0 : Erase not executed 1 : Erase execution in progress RO Program command flag 0 : Program not executed 1 : Program execution in progress RO Reserved bit Set to 0. Read status flag 0 : Disables reading 1 : Enables reading (2) FMR41 FMR42 FMR43 FMR44 -- (b5) FMR46 FMR47 RW 0 : Disable 1 : Enable Erase-suspend request bit Program-suspend request bit (3) Low -pow er consumption read 0 : Disable 1 : Enable mode enable bit (1, 4, 5) RO RO RW NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 2. This bit is enabled w hen the FMR40 bit is set to 1 (enable) and it can be w ritten to during the period betw een issuing an erase command and completing the erase. (This bit is set to 0 during periods other than the above.) In EW0 mode, it can be set to 0 or 1 by a program. In EW1 mode, it is automatically set to 1 if a maskable interrupt is generated during an erase operation w hile the FMR40 bit is set to 1. Do not set this bit to 1 by a program (0 can be w ritten). 3. The FMR42 bit is enabled only w hen the FMR40 bit is set to 1 (enable) and programming to the FMR42 bit is enabled until auto-programming ends after a program command is generated. (This bit is set to 0 during periods other than the above.) In EW0 mode, 0 or 1 can be programmed to the FMR42 bit by a program. In EW1 mode, the FMR42 bit is automatically set to 1 by generating a maskable interrupt during auto-programming w hen the FMR40 bit is set to 1. 1 cannot be w ritten to the FMR42 bit by a program. 4. In high-speed clock mode and high-speed on-chip oscillator mode, set the FMR47 bit to 0 (disabled). 5. Set the FMR01 bit in the FMR0 register to 0 (CPU rew rite mode disabled) in low -pow er-consumption read mode. Figure 19.7 FMR4 Register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 363 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Figure 19.8 shows the Timing of Suspend Operation. Erasure starts Erasure suspends Programming Programming Programming Programming Erasure starts suspends restarts ends restarts During erasure FMR00 bit in FMR0 register 1 FMR46 bit in FMR4 register 1 FMR44 bit in FMR4 register 1 FMR43 bit in FMR4 register 1 During programming During programming Erasure ends During erasure Remains 0 during suspend 0 0 0 0 Remains 1 during suspend Check that the FMR43 bit is set to 1 (during erase execution), and that the erase-operation has not ended. Check that the FMR44 bit is set to 1 (during program execution), and that the program has not ended. Check the status, and that the programming ends normally. Check the status, and that the erasure ends normally. The above figure shows an example of the use of program-suspend during programming following erase-suspend. NOTE: 1. If program-suspend is entered during erase-suspend, always restart programming. Figure 19.8 Timing of Suspend Operation Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 364 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Figure 19.9 shows the How to Set and Exit EW0 Mode. Figure 19.10 shows the How to Set and Exit EW1 Mode. EW0 Mode Operating Procedure Rewrite control program Write 0 to the FMR01 bit before writing 1 (CPU rewrite mode enabled)(2) Set registers(1) CM0 and CM1 Execute software commands Transfer a rewrite control program which uses CPU rewrite mode to the RAM. Execute the read array command(3) Write 0 to the FMR01 bit (CPU rewrite mode disabled) Jump to the rewrite control program which has been transferred to the RAM. (The subsequent process is executed by the rewrite control program in the RAM.) Jump to a specified address in the flash memory NOTES: 1. Select 5 MHz or below for the CPU clock by the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. 2. To set the FMR01 bit to 1, write 0 to the FMR01 bit before writing 1. Do not generate an interrupt between writing 0 and 1. Write to the FMR01 bit in the RAM. 3. Disable the CPU rewrite mode after executing the read array command. Figure 19.9 How to Set and Exit EW0 Mode EW1 Mode Operating Procedure Program in ROM Write 0 to the FMR01 bit before writing 1 (CPU rewrite mode enabled)(1) Write 0 to the FMR11 bit before writing 1 (EW1 mode) Execute software commands Write 0 to the FMR01 bit (CPU rewrite mode disabled) NOTE: 1. To set the FMR01 bit to 1, write 0 to the FMR01 bit before writing 1. Do not generate an interrupt between writing 0 and 1. Figure 19.10 How to Set and Exit EW1 Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 365 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory High-speed on-chip oscillator mode, low-speed on-chip oscillator mode (XIN clock stops), and low-speed clock mode (XIN clock stops) program Transfer a high-speed on-chip oscillator mode, lowspeed on-chip oscillator mode (XIN clock stops), and low-speed clock mode (XIN clock stops) program to the RAM. Jump to the high-speed on-chip oscillator mode, lowspeed on-chip oscillator mode (XIN clock stops), and low-speed clock mode (XIN clock stops) program which has been transferred to the RAM. (The subsequent processing is executed by the program in the RAM.) Write 0 to the FMR01 bit before writing 1 (CPU rewrite mode enabled) Write 1 to the FMSTP bit (flash memory stops. Low power consumption mode)(1) Switch the clock source for the CPU clock. Turn XIN off Process in high-speed on-chip oscillator mode, low-speed on-chip oscillator mode (XIN clock stops), and low-speed clock mode (XIN clock stops) Turn XIN clock on wait until oscillation stabilizes switch the clock source for CPU clock(2) Write 0 to the FMSTP bit (flash memory operation) NOTES: 1. Set the FMR01 bit to 1 (CPU rewrite mode enabled) before setting the FMSTP bit to 1. 2. Before switching to a different clock source for the CPU, make sure the designated clock is stable. 3. Insert a 30 s wait time in a program. Do not access to the flash memory during this wait time. Write 0 to the FMR01 bit (CPU rewrite mode disabled) Wait until the flash memory circuit stabilizes (30 s)(3) Jump to a specified address in the flash memory Figure 19.11 Process to Reduce Power Consumption in High-Speed On-Chip Oscillator Mode, Low-Speed On-Chip Oscillator Mode (XIN Clock Stops) and Low-Speed Clock Mode (XIN Clock Stops) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 366 of 453 R8C/26 Group, R8C/27 Group 19.4.3 19. Flash Memory Software Commands The software commands are described below. Read or write commands and data in 8-bit units. Table 19.4 Software Commands First Bus Cycle Command Read array Read status register Clear status register Program Block erase Mode Write Write Write Write Write Address x x x WA x Data Mode (D7 to D0) FFh 70h Read 50h 40h Write 20h Write Second Bus Cycle Address Data (D7 to D0) x SRD WA BA WD D0h SRD: Status register data (D7 to D0) WA: Write address (Ensure the address specified in the first bus cycle is the same address as the write address specified in the second bus cycle.) WD: Write data (8 bits) BA: Given block address x: Any specified address in the user ROM area 19.4.3.1 Read Array Command The read array command reads the flash memory. The MCU enters read array mode when FFh is written in the first bus cycle. When the read address is entered in the following bus cycles, the content of the specified address can be read in 8-bit units. Since the MCU remains in read array mode until another command is written, the contents of multiple addresses can be read continuously. In addition, the MCU enters read array mode after a reset. 19.4.3.2 Read Status Register Command The read status register command is used to read the status register. When 70h is written in the first bus cycle, the status register can be read in the second bus cycle (refer to 19.4.4 Status Registers). When reading the status register, specify an address in the user ROM area. Do not execute this command in EW1 mode. The MCU remains in read status register mode until the next read array command is written. 19.4.3.3 Clear Status Register Command The clear status register command sets the status register to 0. When 50h is written in the first bus cycle, bits FMR06 to FMR07 in the FMR0 register and SR4 to SR5 in the status register are set to 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 367 of 453 R8C/26 Group, R8C/27 Group 19.4.3.4 19. Flash Memory Program Command The program command writes data to the flash memory in 1-byte units. By writing 40h in the first bus cycle and data in the second bus cycle to the write address, an auto-program operation (data program and verify) will start. Make sure the address value specified in the first bus cycle is the same address as the write address specified in the second bus cycle. The FMR00 bit in the FMR0 register can be used to determine whether auto-programming has completed. When suspend function disabled, the FMR00 bit is set to 0 during auto-programming and set to 1 when autoprogramming completes. When suspend function enabled, the FMR44 bit is set to 1 during auto-programming and set to 0 when autoprogramming completes. The FMR06 bit in the FMR0 register can be used to determine the result of auto-programming after it has been finished (refer to 19.4.5 Full Status Check). Do not write additions to the already programmed addresses. When the FMR02 bit in the FMR0 register is set to 0 (rewriting disabled) or the FMR02 bit is set to 1 (rewriting enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewriting disabled), program commands targeting block 0 are not acknowledged. When the FMR16 bit is set to 1 (rewriting disabled), program commands targeting block 1 are not acknowledged. Figure 19.12 shows the Program Command (When Suspend Function Disabled). Figure 19.13 shows the Program Command (When Suspend Function Enabled). In EW1 mode, do not execute this command for any address which a rewrite control program is allocated. In EW0 mode, the MCU enters read status register mode at the same time auto-programming starts and the status register can be read. The status register bit 7 (SR7) is set to 0 at the same time auto-programming starts and set back to 1 when auto-programming completes. In this case, the MCU remains in read status register mode until the next read array command is written. The status register can be read to determine the result of auto-programming after auto-programming has completed. Start Write the command code 40h to the write address Write data to the write address FMR00 = 1? No Yes Full status check Program completed Figure 19.12 Program Command (When Suspend Function Disabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 368 of 453 R8C/26 Group, R8C/27 Group EW0 Mode 19. Flash Memory Maskable interrupt(1) Start FMR40 = 1 FMR44 = 1 ? Write the command code 40h to the write address No Yes FMR42 = 1(4) I = 1 (enable interrupt)(3) FMR46 = 1 ? No Access flash memory Write data to the write address Yes Access flash memory FMR44 = 0 ? No FMR42 = 0 Yes Full status check REIT Program completed EW1 Mode Start Maskable interrupt (2) FMR40 = 1 Access flash memory REIT Write the command code 40h I = 1 (enable interrupt) Write data to the write address FMR42 = 0 FMR44 = 0 ? No Yes Full status check Program completed NOTES: 1. In EW0 mode, the interrupt vector table and interrupt routine for interrupts to be used should be allocated to the RAM area. 2. td(SR-SUS) is needed until the interrupt request is acknowledged after it is generated. The interrupt to enter suspend should be in interrupt enabled status. 3. When no interrupt is used, the instruction to enable interrupts is not needed. 4. td(SR-SUS) is needed until program is suspended after the FMR42 bit in the FMR4 register is set to 1. Figure 19.13 Program Command (When Suspend Function Enabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 369 of 453 R8C/26 Group, R8C/27 Group 19.4.3.5 19. Flash Memory Block Erase When 20h is written in the first bus cycle and D0h is written to a given address of a block in the second bus cycle, an auto-erase operation (erase and verify) of the specified block starts. The FMR00 bit in the FMR0 register can determine whether auto-erasure has completed. The FMR00 bit is set to 0 during auto-erasure and set to 1 when auto-erasure completes. The FMR07 bit in the FMR0 register can be used to determine the result of auto-erasure after auto-erasure has completed (refer to 19.4.5 Full Status Check). When the FMR02 bit in the FMR0 register is set to 0 (rewriting disabled) or the FMR02 bit is set to 1 (rewriting enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewriting disabled), the block erase commands targeting block 0 are not acknowledged. When the FMR16 bit is set to 1 (rewriting disabled), the block erase commands targeting block 1 are not acknowledged. Do not use the block erase command during program-suspend. Figure 19.14 shows the Block Erase Command (When Erase-Suspend Function Disabled). Figure 19.15 shows the Block Erase Command (When Erase-Suspend Function Enabled). In EW1 mode, do not execute this command for any address to which a rewrite control program is allocated. In EW0 mode, the MCU enters read status register mode at the same time auto-erasure starts and the status register can be read. The status register bit 7 (SR7) is set to 0 at the same time auto-erasure starts and set back to 1 when auto-erasure completes. In this case, the MCU remains in read status register mode until the next read array command is written. Start Write the command code 20h Write D0h to a given block address FMR00 = 1? No Yes Full status check Block erase completed Figure 19.14 Block Erase Command (When Erase-Suspend Function Disabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 370 of 453 R8C/26 Group, R8C/27 Group EW0 Mode 19. Flash Memory Maskable interrupt(1) Start FMR40 = 1 FMR43 = 1 ? Write the command code 20h No Yes FMR41 = 1(4) I = 1 (enable interrupt)(3) FMR46 = 1 ? Write D0h to any block address No Access flash memory Yes Access flash memory FMR00 = 1 ? No FMR41 = 0 Yes Full status check REIT Block erase completed EW1 Mode Start Maskable interrupt (2) FMR40 = 1 Access flash memory Write the command code 20h REIT I = 1 (enable interrupt) Write D0h to any block address FMR41 = 0 FMR00 = 1 ? No Yes Full status check Block erase completed NOTES: 1. In EW0 mode, the interrupt vector table and interrupt routine for interrupts to be used should be allocated to the RAM area. 2. td(SR-SUS) is needed until the interrupt request is acknowledged after it is generated. The interrupt to enter suspend should be in interrupt enabled status. 3. When no interrupt is used, the instruction to enable interrupts is not needed. 4. td(SR-SUS) is needed until erase is suspended after the FMR41 bit in the FMR4 register is set to 1. Figure 19.15 Block Erase Command (When Erase-Suspend Function Enabled) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 371 of 453 R8C/26 Group, R8C/27 Group 19.4.4 19. Flash Memory Status Registers The status register indicates the operating status of the flash memory and whether an erase or program operation has completed normally or in error. Status of the status register can be read by bits FMR00, FMR06, and FMR07 in the FMR0 register. Table 19.5 lists the Status Register Bits. In EW0 mode, the status register can be read in the following cases: * When a given address in the user ROM area is read after writing the read status register command * When a given address in the user ROM area is read after executing the program or block erase command but before executing the read array command. 19.4.4.1 Sequencer Status (SR7 and FMR00 Bits) The sequencer status bits indicate the operating status of the flash memory. SR7 is set to 0 (busy) during autoprogramming and auto-erasure, and is set to 1 (ready) at the same time the operation completes. 19.4.4.2 Erase Status (SR5 and FMR07 Bits) Refer to 19.4.5 Full Status Check. 19.4.4.3 Program Status (SR4 and FMR06 Bits) Refer to 19.4.5 Full Status Check. Table 19.5 Status Register Bits SR0 (D0) SR1 (D1) SR2 (D2) SR3 (D3) SR4 (D4) FMR0 Register Bit - - - - FMR06 Reserved Reserved Reserved Reserved Program status SR5 (D5) FMR07 Erase status SR6 (D6) SR7 (D7) - FMR00 Reserved Sequencer status Status Register Bit Status Name Description 0 - - - - Completed normally Completed normally - Busy Value after Reset 1 - - - - Error - - - - 0 Error 0 - Ready - 1 D0 to D7: Indicate the data bus which is read when the read status register command is executed. Bits FMR07 (SR5) to FMR06 (SR4) are set to 0 by executing the clear status register command. When the FMR07 bit (SR5) or FMR06 bit (SR4) is set to 1, the program and block erase commands cannot be accepted. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 372 of 453 R8C/26 Group, R8C/27 Group 19.4.5 19. Flash Memory Full Status Check When an error occurs, bits FMR06 to FMR07 in the FMR0 register are set to 1, indicating the occurrence of an error. Therefore, checking these status bits (full status check) can be used to determine the execution result. Table 19.6 lists the Errors and FMR0 Register Status. Figure 19.16 shows the Full Status Check and Handling Procedure for Individual Errors. Table 19.6 Errors and FMR0 Register Status FMR0 Register (Status Register) Status Error FMR07 (SR5) FMR06 (SR4) 1 1 Command sequence error 1 0 Erase error 0 1 Program error Error Occurrence Condition * When a command is not written correctly * When invalid data other than that which can be written in the second bus cycle of the block erase command is written (i.e., other than D0h or FFh)(1) * When the program command or block erase command is executed while rewriting is disabled by the FMR02 bit in the FMR0 register, or the FMR15 or FMR16 bit in the FMR1 register. * When an address not allocated in flash memory is input during erase command input * When attempting to erase the block for which rewriting is disabled during erase command input. * When an address not allocated in flash memory is input during write command input. * When attempting to write to a block for which rewriting is disabled during the write command input. * When the block erase command is executed but autoerasure does not complete correctly * When the program command is executed but not autoprogramming does not complete. NOTE: 1. The MCU enters read array mode when FFh is written in the second bus cycle of these commands. At the same time, the command code written in the first bus cycle is disabled. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 373 of 453 R8C/26 Group, R8C/27 Group 19. Flash Memory Command sequence error Full status check Execute the clear status register command (set these status flags to 0) FMR06 = 1 and FMR07 = 1? Yes Command sequence error Check if command is properly input No Re-execute the command FMR07 = 1? Yes Erase error Erase error No Execute the clear status register command (set these status flags to 0) Erase command re-execution times 3 times? FMR06 = 1? Yes Program error No Yes Re-execute block erase command No Program error Execute the clear status register command (set these status flags to 0) Full status check completed Specify the other address besides the write address where the error occurs for the program address(1) NOTE: 1. To rewrite to the address where the program error occurs, check if the full status check is complete normally and write to the address after the block erase command is executed. Figure 19.16 Re-execute program command Full Status Check and Handling Procedure for Individual Errors Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 374 of 453 Block targeting for erasure cannot be used R8C/26 Group, R8C/27 Group 19.5 19. Flash Memory Standard Serial I/O Mode In standard serial I/O mode, the user ROM area can be rewritten while the MCU is mounted on-board by using a serial programmer which is suitable for the MCU. There are three types of Standard serial I/O modes: * Standard serial I/O mode 1 ............Clock synchronous serial I/O used to connect with a serial programmer * Standard serial I/O mode 2 ............Clock asynchronous serial I/O used to connect with a serial programmer * Standard serial I/O mode 3 ............Special clock asynchronous serial I/O used to connect with a serial programmer This MCU uses Standard serial I/O mode 2 and Standard serial I/O mode 3. Refer to Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator. Contact the manufacturer of your serial programmer for details. Refer to the user's manual of your serial programmer for instructions on how to use it. Table 19.7 lists the Pin Functions (Flash Memory Standard Serial I/O Mode 2), Table 19.8 lists the Pin Functions (Flash Memory Standard Serial I/O Mode 3), and Figure 19.17 shows the Pin Connections for Standard Serial I/O Mode 3. After processing the pins shown in Table 19.8 and rewriting the flash memory using the programmer, apply "H" to the MODE pin and reset the hardware to run a program in the flash memory in single-chip mode. 19.5.1 ID Code Check Function The ID code check function determines whether the ID codes sent from the serial programmer and those written in the flash memory match (refer to 19.3 Functions to Prevent Rewriting of Flash Memory). Table 19.7 Pin Functions (Flash Memory Standard Serial I/O Mode 2) Pin VCC,VSS Name Power input I/O RESET P4_6/XIN/XCIN P4_7/XOUT/XCOUT P0_0 to P0_7 P1_0 to P1_7 P3_0, P3_1, P3_3 to P3_6 P4_2/VREF P5_3, P5_4 MODE P3_7 P4_5 Reset input I P4_6 input/clock input P4_7 input/clock output Input port P0 Input port P1 Input port P3 I Connect a ceramic resonator or crystal oscillator between the XIN/XCIN and XOUT/XCOUT pins. I/O I Input "H" or "L" level signal or leave the pin open. I I Input port P4 Input port P5 MODE TXD output RXD input I I I/O Input "L". O Serial data output pin. I Serial data input pin. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 375 of 453 Description Apply the voltage guaranteed for programming and erasure to the VCC pin and 0 V to the VSS pin. Reset input pin. R8C/26 Group, R8C/27 Group Table 19.8 19. Flash Memory Pin Functions (Flash Memory Standard Serial I/O Mode 3) Pin VCC,VSS Name Power input I/O Description Apply the voltage guaranteed for programming and erasure to the VCC pin and 0 V to the VSS pin. Reset input pin. RESET P4_6/XIN/XCIN Reset input I P4_6 input/clock input I P0_0 to P0_7 P1_0 to P1_7 P3_0, P3_1, P3_3 to P3_7 P4_2/VREF, P4_5 P5_3, P5_4 MODE Input port P0 Input port P1 Input port P3 I I I Input port P4 Input port P5 MODE I I I/O Serial data I/O pin. Connect to the flash programmer. Connect a ceramic resonator or crystal oscillator between the XIN/XCIN and XOUT/XCOUT pins P4_7/XOUT/XCOUT P4_7 input/clock output I/O when connecting external oscillator. Apply "H" and "L" or leave the pin open when using as input port. Input "H" or "L" level signal or leave the pin open. 24 23 22 21 20 19 18 17 25 16 26 15 27 14 28 13 R8C/26 Group R8C/27 Group 29 12 30 11 31 10 32 9 1 2 3 4 5 6 7 8 MODE VSS VCC Connect oscillator circuit(1) Mode setting Signal Value MODE Voltage from programmer RESET VSS VCC Figure 19.17 Package: PLQP0032GB-A NOTE: 1. It is not necessary to connect an oscillating circuit when operating with the on-chip oscillator clock. Pin Connections for Standard Serial I/O Mode 3 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 376 of 453 R8C/26 Group, R8C/27 Group 19.5.1.1 19. Flash Memory Example of Circuit Application in the Standard Serial I/O Mode Figure 19.18 shows an Example of Pin Processing in Standard Serial I/O Mode 2, Figure 19.19 shows an Example of Pin Processing in Standard Serial I/O Mode 3. Since the controlled pins vary depending on the programmer, refer to the manual of your serial programmer for details. MCU Data Output TXD Data Input RXD MODE NOTES: 1. In this example, modes are switched between single-chip mode and standard serial I/O mode by controlling the MODE input with a switch. 2. Connecting the oscillation is necessary. Set the main clock frequency 1 MHz to 20 MHz. Refer to Appendix Figure 2.1 Connection Example with M16C Flash Starter (M3A-0806). Figure 19.18 Example of Pin Processing in Standard Serial I/O Mode 2 MCU MODE I/O MODE Reset input RESET User reset signal NOTES: 1. Controlled pins and external circuits vary depending on the programmer. Refer to the programmer manual for details. 2. In this example, modes are switched between single-chip mode and standard serial I/O mode by connecting a programmer. 3. When operating with the on-chip oscillator clock, it is not necessary to connect an oscillating circuit. Figure 19.19 Example of Pin Processing in Standard Serial I/O Mode 3 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 377 of 453 R8C/26 Group, R8C/27 Group 19.6 19. Flash Memory Parallel I/O Mode Parallel I/O mode is used to input and output software commands, addresses and data necessary to control (read, program, and erase) the on-chip flash memory. Use a parallel programmer which supports this MCU. Contact the manufacturer of the parallel programmer for more information, and refer to the user's manual of the parallel programmer for details on how to use it. ROM areas shown in Figures 19.1 and 19.2 can be rewritten in parallel I/O mode. 19.6.1 ROM Code Protect Function The ROM code protect function disables the reading and rewriting of the flash memory. (Refer to 19.3 Functions to Prevent Rewriting of Flash Memory.) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 378 of 453 R8C/26 Group, R8C/27 Group 19.7 19. Flash Memory Notes on Flash Memory 19.7.1 CPU Rewrite Mode 19.7.1.1 Operating Speed Before entering CPU rewrite mode (EW0 mode), select 5 MHz or below for the CPU clock using the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. This does not apply to EW1 mode. 19.7.1.2 Prohibited Instructions The following instructions cannot be used in EW0 mode because they reference internal data in flash memory: UND, INTO, and BRK. 19.7.1.3 Interrupts Table 19.9 lists the EW0 Mode Interrupts and Table 19.10 lists the EW1 Mode Interrupt. Table 19.9 Mode EW0 Mode Interrupts When Maskable Interrupt Request is Acknowledged Status EW0 During auto-erasure Any interrupt can be used by allocating a vector in RAM Auto-programming When Watchdog Timer, Oscillation Stop Detection, Voltage Monitor 1, or Voltage Monitor 2 Interrupt Request is Acknowledged Once an interrupt request is acknowledged, the auto-programming or auto-erasure is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after the fixed period and the flash memory restarts. Since the block during autoerasure or the address during autoprogramming is forcibly stopped, the normal value may not be read. Execute auto-erasure again and ensure it completes normally. Since the watchdog timer does not stop during the command operation, interrupt requests may be generated. Reset the watchdog timer regularly. NOTES: 1. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. 2. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 379 of 453 R8C/26 Group, R8C/27 Group Table 19.10 Mode 19. Flash Memory EW1 Mode Interrupt When Watchdog Timer, Oscillation Stop Detection, Voltage Monitor 1, or Voltage Monitor 2 Interrupt Request is Acknowledged Auto-erasure is suspended after Once an interrupt request is acknowledged, auto-programming or td(SR-SUS) and interrupt auto-erasure is forcibly stopped handling is executed. Autoimmediately and the flash memory is erasure can be restarted by reset. Interrupt handling starts after the setting the FMR41 bit in the FMR4 register to 0 (erase restart) fixed period and the flash memory restarts. Since the block during autoafter interrupt handling erasure or the address during autocompletes. Auto-erasure has priority and the programming is forcibly stopped, the normal value may not be read. Execute interrupt request auto-erasure again and ensure it acknowledgement is put on completes normally. standby. Interrupt handling is Since the watchdog timer does not stop executed after auto-erasure during the command operation, completes. Auto-programming is suspended interrupt requests may be generated. Reset the watchdog timer regularly after td(SR-SUS) and interrupt using the erase-suspend function. handling is executed. Auto-programming can be restarted by setting the FMR42 bit in the FMR4 register to 0 (program restart) after interrupt handling completes. Auto-programming has priority and the interrupt request acknowledgement is put on standby. Interrupt handling is executed after auto-programming completes. When Maskable Interrupt Request is Acknowledged Status EW1 During auto-erasure (erase-suspend function enabled) During auto-erasure (erase-suspend function disabled) During autoprogramming (program suspend function enabled) During autoprogramming (program suspend function disabled) NOTES: 1. Do not use the address match interrupt while a command is executing because the vector of the address match interrupt is allocated in ROM. 2. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 380 of 453 R8C/26 Group, R8C/27 Group 19.7.1.4 19. Flash Memory How to Access Write 0 before writing 1 when setting the FMR01, FMR02, or FMR11 bit to 1. Do not generate an interrupt between writing 0 and 1. 19.7.1.5 Rewriting User ROM Area In EW0 Mode, if the supply voltage drops while rewriting any block in which a rewrite control program is stored, it may not be possible to rewrite the flash memory because the rewrite control program cannot be rewritten correctly. In this case, use standard serial I/O mode. 19.7.1.6 Program Do not write additions to the already programmed address. 19.7.1.7 Entering Stop Mode or Wait Mode Do not enter stop mode or wait mode during erase-suspend. 19.7.1.8 Program and Erase Voltage for Flash Memory To perform programming and erasure, use VCC = 2.7 to 5.5 V as the supply voltage. Do not perform programming and erasure at less than 2.7 V. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 381 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics 20. Electrical Characteristics 20.1 N, D Version Table 20.1 Absolute Maximum Ratings Symbol VCC/AVCC VI VO Pd Topr Parameter Supply voltage Input voltage Output voltage Power dissipation Operating ambient temperature Tstg Storage temperature Table 20.2 IOH(sum) IOH(peak) IOH(avg) IOL(sum) IOL(sum) IOL(peak) IOL(avg) f(XIN) f(XCIN) - Topr = 25C Rated Value -0.3 to 6.5 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 500 -20 to 85 (N version) / -40 to 85 (D version) -65 to 150 Unit V V V mW C C Recommended Operating Conditions Symbol VCC/AVCC VSS/AVSS VIH VIL IOH(sum) Condition Parameter Supply voltage Supply voltage Input "H" voltage Input "L" voltage Peak sum output Sum of all pins IOH(peak) "H" current Average sum Sum of all pins IOH(avg) output "H" current Peak output "H" Except P1_0 to P1_7 current P1_0 to P1_7 Average output Except P1_0 to P1_7 "H" current P1_0 to P1_7 Peak sum output Sum of all pins IOL(peak) "L" currents Average sum Sum of all pins IOL(avg) output "L" currents Peak output "L" Except P1_0 to P1_7 currents P1_0 to P1_7 Average output Except P1_0 to P1_7 "L" current P1_0 to P1_7 XIN clock input oscillation frequency XCIN clock input oscillation frequency System clock OCD2 = 0 XlN clock selected OCD2 = 1 On-chip oscillator clock selected Conditions 3.0 V VCC 5.5 V 2.7 V VCC < 3.0 V 2.2 V VCC < 2.7 V 2.2 V VCC 5.5 V 3.0 V VCC 5.5 V 2.7 V VCC < 3.0 V 2.2 V VCC < 2.7 V FRA01 = 0 Low-speed on-chip oscillator clock selected FRA01 = 1 High-speed on-chip oscillator clock selected 3.0 V VCC 5.5 V FRA01 = 1 High-speed on-chip oscillator clock selected 2.7 V VCC 5.5 V FRA01 = 1 High-speed on-chip oscillator clock selected 2.2 V VCC 5.5 V Min. 2.2 - 0.8 VCC 0 - Standard Typ. - 0 - - - Max. 5.5 - VCC 0.2 VCC -160 - - -80 mA - - - - - - - - - - -10 -40 -5 -20 160 mA mA mA mA mA - - 80 mA - - - - 0 0 0 0 0 0 0 - - - - - - - - - - - - 125 10 40 5 20 20 10 5 70 20 10 5 - mA mA mA mA MHz MHz MHz kHz MHz MHz MHz kHz - - 20 MHz - - 10 MHz - - 5 MHz NOTES: 1. VCC = 2.2 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. The average output current indicates the average value of current measured during 100 ms. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 382 of 453 Unit V V V V mA R8C/26 Group, R8C/27 Group Table 20.3 A/D Converter Characteristics Symbol - - Rladder tconv Vref VIA - 20. Electrical Characteristics Parameter Resolution Absolute accuracy Conditions Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 3.3 V AD = 10 MHz, Vref = AVCC = 3.3 V AD = 5 MHz, Vref = AVCC = 2.2 V AD = 5 MHz, Vref = AVCC = 2.2 V Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V 10-bit mode 8-bit mode 10-bit mode 8-bit mode 10-bit mode 8-bit mode Resistor ladder Conversion time 10-bit mode 8-bit mode Reference voltage Analog input voltage(2) A/D operating Without sample and hold clock frequency With sample and hold Without sample and hold With sample and hold Vref = AVCC = 2.7 to 5.5 V Vref = AVCC = 2.7 to 5.5 V Vref = AVCC = 2.2 to 5.5 V Vref = AVCC = 2.2 to 5.5 V Min. - - - - - - - 10 3.3 2.8 2.2 0 0.25 1 0.25 1 Standard Typ. Max. - 10 - 3 - 2 - 5 - 2 - 5 - 2 - 40 - - - - - AVCC - AVCC - - - - 10 10 5 5 Unit Bits LSB LSB LSB LSB LSB LSB k s s V V MHz MHz MHz MHz NOTES: 1. AVCC = 2.2 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in 8-bit mode. P0 P1 P3 30pF P4 P5 Figure 20.1 Ports P0, P1, and P3 to P5 Timing Measurement Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 383 of 453 R8C/26 Group, R8C/27 Group Table 20.4 Flash Memory (Program ROM) Electrical Characteristics Symbol - - Parameter Program/erase endurance(2) - Byte program time Block erase time Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature - Data hold time(7) - td(SR-SUS) - - - - - 20. Electrical Characteristics Conditions Min. Standard Typ. - Unit Max. - times R8C/26 Group 100(3) R8C/27 Group 1,000(3) - - - - - times 50 0.4 - s 650 - 400 9 97 + CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.2 0 20 - 3 + CPU clock x 4 cycles 5.5 5.5 60 - Ambient temperature = 55C - - - s s V V C year NOTES: 1. VCC = 2.7 to 5.5 V at Topr = 0 to 60C, unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 100 or 1,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. It is also advisable to retain data on the erasure endurance of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 384 of 453 R8C/26 Group, R8C/27 Group Table 20.5 Flash Memory (Data flash Block A, Block B) Electrical Characteristics(4) Symbol - - - - - td(SR-SUS) - - - - - - - 20. Electrical Characteristics Parameter Conditions Program/erase endurance(2) Byte program time (program/erase endurance 1,000 times) Byte program time (program/erase endurance > 1,000 times) Block erase time (program/erase endurance 1,000 times) Block erase time (program/erase endurance > 1,000 times) Data hold Ambient temperature = 55C Standard Typ. - Unit Max. - times 50 400 s - 65 - s - 0.2 9 s - 0.3 - s - - s 650 - 97 + CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.2 - -20(8) 20 - 3 + CPU clock x 4 cycles 5.5 5.5 85 - - year 10,000(3) - Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature time(9) Min. - V V C NOTES: 1. VCC = 2.7 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. Standard of block A and block B when program and erase endurance exceeds 1,000 times. Byte program time to 1,000 times is the same as that in program ROM. 5. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. In addition, averaging the erasure endurance between blocks A and B can further reduce the actual erasure endurance. It is also advisable to retain data on the erasure endurance of each block and limit the number of erase operations to a certain number. 6. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 7. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 8. -40C for D version. 9. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 385 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Suspend request (maskable interrupt request) FMR46 Clock-dependent time Fixed time Access restart td(SR-SUS) Figure 20.2 Table 20.6 Time delay until Suspend Voltage Detection 0 Circuit Electrical Characteristics Symbol Vdet0 - td(E-A) Vccmin Parameter Condition Voltage detection level Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(2) MCU operating voltage minimum value VCA25 = 1, VCC = 5.0 V Min. 2.2 - - 2.2 Standard Typ. Max. 2.3 2.4 0.9 - - 300 - - Unit V A s V NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA25 bit in the VCA2 register to 0. Table 20.7 Voltage Detection 1 Circuit Electrical Characteristics Symbol Vdet1 - Parameter Condition Voltage detection level(4) time(2) - td(E-A) Voltage monitor 1 interrupt request generation Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(3) VCA26 = 1, VCC = 5.0 V Min. 2.70 Standard Typ. Max. 2.85 3.00 Unit V - 40 - s - 0.6 - - A 100 s - NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Time until the voltage monitor 1 interrupt request is generated after the voltage passes Vdet1. 3. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA26 bit in the VCA2 register to 0. 4. This parameter shows the voltage detection level when the power supply drops. The voltage detection level when the power supply rises is higher than the voltage detection level when the power supply drops by approximately 0.1 V. Table 20.8 Voltage Detection 2 Circuit Electrical Characteristics Symbol Vdet2 - - td(E-A) Parameter Condition Voltage detection level time(2) Voltage monitor 2 interrupt request generation Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(3) VCA27 = 1, VCC = 5.0 V Min. 3.3 Standard Typ. Max. 3.6 3.9 Unit V - 40 - s - 0.6 - - A 100 s - NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Time until the voltage monitor 2 interrupt request is generated after the voltage passes Vdet2. 3. Necessary time until the voltage detection circuit operates after setting to 1 again after setting the VCA27 bit in the VCA2 register to 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 386 of 453 R8C/26 Group, R8C/27 Group Table 20.9 Power-on Reset Circuit, Voltage Monitor 0 Reset Electrical Characteristics(3) Symbol Vpor1 20. Electrical Characteristics Parameter Condition Vpor2 Power-on reset valid voltage(4) Power-on reset or voltage monitor 0 reset valid voltage trth External power VCC rise gradient(2) Min. - Standard Typ. - Max. 0.1 0 - Vdet0 V 20 - - mV/msec Unit V NOTES: 1. The measurement condition is Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. This condition (external power VCC rise gradient) does not apply if VCC 1.0 V. 3. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. 4. tw(por1) indicates the duration the external power VCC must be held below the effective voltage (Vpor1) to enable a power on reset. When turning on the power for the first time, maintain tw(por1) for 30 s or more if -20C Topr 85C, maintain tw(por1) for 3,000 s or more if -40C Topr < -20C. Vdet0(3) Vdet0(3) 2.2 V trth trth External Power VCC Vpor2 Vpor1 Sampling time(1, 2) tw(por1) Internal reset signal ("L" valid) 1 x 32 fOCO-S 1 x 32 fOCO-S NOTES: 1. When using the voltage monitor 0 digital filter, ensure that the voltage is within the MCU operation voltage range (2.2 V or above) during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection Circuit for details. Figure 20.3 Reset Circuit Electrical Characteristics Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 387 of 453 R8C/26 Group, R8C/27 Group Table 20.10 20. Electrical Characteristics High-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter fOCO40M High-speed on-chip oscillator frequency temperature * supply voltage dependence High-speed on-chip oscillator frequency when correction value in FRA7 register is written to FRA1 register(4) - Value in FRA1 register after reset - Oscillation frequency adjustment unit of highspeed on-chip oscillator Oscillation stability time Self power consumption at oscillation - - Condition VCC = 4.75 to 5.25 V 0C Topr 60C(2) VCC = 3.0 to 5.5 V -20C Topr 85C(2) VCC = 3.0 to 5.5 V -40C Topr 85C(2) VCC = 2.7 to 5.5 V -20C Topr 85C(2) VCC = 2.7 to 5.5 V -40C Topr 85C(2) VCC = 2.2 to 5.5 V -20C Topr 85C(3) VCC = 2.2 to 5.5 V -40C Topr 85C(3) VCC = 5.0 V 10% -20C Topr 85C(2) VCC = 5.0 V 10% -40C Topr 85C(2) VCC = 5.0 V, Topr = 25C VCC = 3.0 to 5.5 V -20C Topr 85C Adjust FRA1 register (value after reset) to -1 Min. 39.2 Standard Typ. 40 Max. 40.8 MHz 38.8 40 41.2 MHz 38.4 40 41.6 MHz 38 40 42 MHz 37.6 40 42.4 MHz 35.2 40 44.8 MHz 34 40 46 MHz 38.8 40 40.8 MHz 38.4 40 40.8 MHz - -3% 36.864 - - 3% MHz % 08h(3) - - +0.3 F7h(3) - MHz 10 400 100 - A - VCC = 5.0 V, Topr = 25C - Unit - s NOTES: 1. VCC = 2.2 to 5.5 V, Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. These standard values show when the FRA1 register value after reset is assumed. 3. These standard values show when the corrected value of the FRA6 register is written to the FRA1 register. 4. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in UART mode. Table 20.11 Low-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter fOCO-S - - Low-speed on-chip oscillator frequency Oscillation stability time Self power consumption at oscillation Condition VCC = 5.0 V, Topr = 25C Standard Typ. 125 10 15 Min. 30 - - Max. 250 100 - Unit kHz s A NOTE: 1. VCC = 2.2 to 5.5 V, Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. Table 20.12 Power Supply Circuit Timing Characteristics Symbol Parameter td(P-R) Time for internal power supply stabilization during power-on(2) td(R-S) STOP exit time(3) Condition NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = 25C. 2. Waiting time until the internal power supply generation circuit stabilizes during power-on. 3. Time until system clock supply starts after the interrupt is acknowledged to exit stop mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 388 of 453 Min. 1 - Standard Typ. Max. - 2000 - 150 Unit s s R8C/26 Group, R8C/27 Group Table 20.13 Symbol Timing Requirements of Clock Synchronous Serial I/O with Chip Select(1) Parameter tSUCYC SSCK clock cycle time tHI tLO tRISE SSCK clock "H" width SSCK clock "L" width SSCK clock rising time tFALL 20. Electrical Characteristics SSCK clock falling time Conditions Standard Typ. - - Unit Max. - - - - - - - 100 1 - 1 - - tCYC(2) s ns - - tCYC(2) Slave 1tCYC + 50 - - ns Slave 1tCYC + 50 - - ns - - 1 - - - - - - - - 1.5tCYC + 100 1.5tCYC + 200 1.5tCYC + 100 1.5tCYC + 200 tCYC(2) ns ns ns ns Master Slave Master Slave SSO, SSI data input setup time SSO, SSI data input hold time tLEAD SCS setup time tOD SCS hold time SSO, SSI data output delay time tSA SSI slave access time tOR SSI slave out open time 2.7 V VCC 5.5 V 2.2 V VCC < 2.7 V 2.7 V VCC 5.5 V 2.2 V VCC < 2.7 V - 0.6 0.6 1 1 1 NOTES: 1. VCC = 2.2 to 5.5 V, VSS = 0 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. 1tCYC = 1/f1(s) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 tCYC(2) tSUCYC tSUCYC 0.4 0.4 - tSU tH tLAG Min. 4 Page 389 of 453 tCYC(2) s R8C/26 Group, R8C/27 Group 20. Electrical Characteristics 4-Wire Bus Communication Mode, Master, CPHS = 1 VIH or VOH SCS (output) VIH or VOH tHI tFALL tRISE SSCK (output) (CPOS = 1) tLO tHI SSCK (output) (CPOS = 0) tLO tSUCYC SSO (output) tOD SSI (input) tSU tH 4-Wire Bus Communication Mode, Master, CPHS = 0 VIH or VOH SCS (output) VIH or VOH tHI tFALL tRISE SSCK (output) (CPOS = 1) tLO tHI SSCK (output) (CPOS = 0) tLO tSUCYC SSO (output) tOD SSI (input) tSU tH CPHS, CPOS: Bits in SSMR register Figure 20.4 I/O Timing of Clock Synchronous Serial I/O with Chip Select (Master) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 390 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics 4-Wire Bus Communication Mode, Slave, CPHS = 1 VIH or VOH SCS (input) VIH or VOH tLEAD tHI tFALL tRISE tLAG SSCK (input) (CPOS = 1) tLO tHI SSCK (input) (CPOS = 0) tLO tSUCYC SSO (input) tSU tH SSI (output) tSA tOD tOR 4-Wire Bus Communication Mode, Slave, CPHS = 0 VIH or VOH SCS (input) VIH or VOH tLEAD tHI tFALL tRISE tLAG SSCK (input) (CPOS = 1) tLO tHI SSCK (input) (CPOS = 0) tLO tSUCYC SSO (input) tSU tH SSI (output) tSA tOD tOR CPHS, CPOS: Bits in SSMR register Figure 20.5 I/O Timing of Clock Synchronous Serial I/O with Chip Select (Slave) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 391 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics tHI VIH or VOH SSCK VIH or VOH tLO tSUCYC SSO (output) tOD SSI (input) tSU Figure 20.6 tH I/O Timing of Clock Synchronous Serial I/O with Chip Select (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 392 of 453 R8C/26 Group, R8C/27 Group Table 20.14 20. Electrical Characteristics Timing Requirements of I2C bus Interface(1) tSCL SCL input cycle time tSCLH SCL input "H" width Standard Typ. - 12tCYC + 600(2) - 3tCYC + 300(2) tSCLL SCL input "L" width 500(2) tsf tSP SCL, SDA input fall time SCL, SDA input spike pulse rejection time tBUF SDA input bus-free time 5tCYC(2) - 1tCYC(2) - tSTAH Start condition input hold time 3tCYC(2) - - ns tSTAS Retransmit start condition input setup time 3tCYC(2) - - ns tSTOP Stop condition input setup time 3tCYC(2) - - ns tSDAS Data input setup time - - ns tSDAH Data input hold time 1tCYC + 20(2) 0 - - ns Symbol Parameter Condition Min. 5tCYC + - - Unit Max. - ns - ns - ns - 300 - ns ns - NOTES: 1. VCC = 2.2 to 5.5 V, VSS = 0 V and Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. 1tCYC = 1/f1(s) VIH SDA VIL tBUF tSTAH tSCLH tSTAS tSP tSTOP SCL P(2) S(1) tsf Sr(3) tSCLL tsr tSCL NOTES: 1. Start condition 2. Stop condition 3. Retransmit start condition Figure 20.7 I/O Timing of I2C bus Interface Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 393 of 453 P(2) tSDAS tSDAH ns R8C/26 Group, R8C/27 Group Table 20.15 Electrical Characteristics (1) [VCC = 5 V] Symbol VOH Parameter Output "H" voltage Except P1_0 to P1_7, XOUT P1_0 to P1_7 XOUT VOL Output "L" voltage Except P1_0 to P1_7, XOUT P1_0 to P1_7 XOUT VT+-VT- 20. Electrical Characteristics Hysteresis Condition IOH = -5 mA IOH = -200 A Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 5 mA IOL = 200 A Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD1, CLK0, CLK1, SSI, SCL, SDA, SSO RESET IIH IIL RPULLUP RfXIN RfXCIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback XIN resistance Feedback XCIN resistance RAM hold voltage VI = 5 V, VCC = 5 V VI = 0 V, VCC = 5 V VI = 0 V, VCC = 5 V During stop mode IOH = -20 mA IOH = -5 mA IOH = -1 mA IOH = -500 A IOL = 20 mA IOL = 5 mA IOL = 1 mA IOL = 500 A Min. VCC - 2.0 VCC - 0.5 VCC - 2.0 VCC - 2.0 VCC - 2.0 VCC - 2.0 - - - - - - 0.1 Standard Typ. - - - - - - - - - - - - 0.5 Max. VCC VCC VCC VCC VCC VCC 2.0 0.45 2.0 2.0 2.0 2.0 - Unit V V V V V V V V V V V V V 0.1 1.0 - V - - - 30 - 50 1.0 5.0 -5.0 167 - A - A k M - 18 - M 1.8 - - V NOTE: 1. VCC = 4.2 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 20 MHz, unless otherwise specified. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 394 of 453 R8C/26 Group, R8C/27 Group Table 20.16 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (2) [Vcc = 5 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 3.3 to 5.5 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Low-speed clock mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz Program operation on RAM Flash memory off, FMSTP = 1 Page 395 of 453 Min. - Standard Typ. Max. 10 17 Unit mA - 9 15 mA - 6 - mA - 5 - mA - 4 - mA - 2.5 - mA - 10 15 mA - 4 - mA - 5.5 10 mA - 2.5 - mA - 130 300 A - 130 300 A - 30 - A R8C/26 Group, R8C/27 Group Table 20.17 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (3) [Vcc = 5 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current Wait mode (VCC = 3.3 to 5.5 V) Single-chip mode, output pins are open, other pins are VSS Stop mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (high drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (low drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 396 of 453 Min. - Standard Typ. Max. 25 75 Unit A - 23 60 A - 4.0 - A - 2.2 - A - 0.8 3.0 A - 1.2 - A R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Timing Requirements (Unless Otherwise Specified: VCC = 5 V, VSS = 0 V at Topr = 25C) [VCC = 5 V] Table 20.18 XIN Input, XCIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) tc(XCIN) tWH(XCIN) tWL(XCIN) Standard Min. Max. 50 - 25 - 25 - 14 - 7 - 7 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width XCIN input cycle time XCIN input "H" width XCIN input "L" width tC(XIN) Unit ns ns ns s s s VCC = 5 V tWH(XIN) XIN input tWL(XIN) Figure 20.8 Table 20.19 XIN Input and XCIN Input Timing Diagram when VCC = 5 V TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 100 - 40 - 40 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 20.9 TRAIO Input Timing Diagram when VCC = 5 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 397 of 453 Unit ns ns ns VCC = 5 V R8C/26 Group, R8C/27 Group Table 20.20 20. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 200 - 100 - 100 - - 50 0 - 50 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0 or 1 VCC = 5 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0 or 1 Figure 20.10 Table 20.21 Serial Interface Timing Diagram when VCC = 5 V External Interrupt INTi (i = 0, 1, 3) Input tW(INH) INTi input "H" width Standard Min. Max. (1) - 250 tW(INL) INTi input "L" width 250(2) Symbol Parameter - Unit ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 5 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 20.11 External Interrupt INTi Input Timing Diagram when VCC = 5 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 398 of 453 R8C/26 Group, R8C/27 Group Table 20.22 Electrical Characteristics (3) [VCC = 3 V] Symbol VOH 20. Electrical Characteristics Parameter Output "H" voltage Except P1_0 to P1_7, XOUT P1_0 to P1_7 Output "L" voltage IIH IIL RPULLUP RfXIN RfXCIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback resistance Feedback resistance RAM hold voltage Max. VCC Unit V VCC - 0.5 - VCC V IOH = -1 mA VCC - 0.5 - VCC V IOH = -0.1 mA VCC - 0.5 - VCC V IOH = -50 A VCC - 0.5 - VCC V - - 0.5 V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 5 mA - - 0.5 V IOL = 1 mA - - 0.5 V IOL = 0.1 mA - - 0.5 V IOL = 50 A - - 0.5 V INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD1, CLK0, CLK1, SSI, SCL, SDA, SSO 0.1 0.3 - V RESET 0.1 0.4 - V - - - 66 - - 1.8 160 3.0 18 - 4.0 -4.0 500 - - - A - Except P1_0 to P1_7, XOUT P1_0 to P1_7 Hysteresis Standard Typ. - IOH = -5 mA XOUT VT+-VT- IOH = -1 mA Min. VCC - 0.5 Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 1 mA XOUT VOL Condition VI = 3 V, VCC = 3 V VI = 0 V, VCC = 3 V VI = 0 V, VCC = 3 V XIN XCIN During stop mode A k M M V NOTE: 1. VCC = 2.7 to 3.3 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 10 MHz, unless otherwise specified. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 399 of 453 R8C/26 Group, R8C/27 Group Table 20.23 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (4) [Vcc = 3 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 2.7 to 3.3 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Low-speed clock mode Wait mode Stop mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz Program operation on RAM Flash memory off, FMSTP = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (high drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (low drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 400 of 453 Min. - Standard Typ. Max. 6 - Unit mA - 2 - mA - 5 9 mA - 2 - mA - 130 300 A - 130 300 A - 30 - A - 25 70 A - 23 55 A - 3.8 - A - 2.0 - A - 0.7 3.0 A - 1.1 - A R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Timing requirements (Unless Otherwise Specified: VCC = 3 V, VSS = 0 V at Topr = 25C) [VCC = 3 V] Table 20.24 XIN Input, XCIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) tc(XCIN) tWH(XCIN) tWL(XCIN) Standard Min. Max. 100 - 40 - 40 - 14 - 7 - 7 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width XCIN input cycle time XCIN input "H" width XCIN input "L" width tC(XIN) Unit ns ns ns s s s VCC = 3 V tWH(XIN) XIN input tWL(XIN) XIN Input and XCIN Input Timing Diagram when VCC = 3 V Figure 20.12 Table 20.25 TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 300 - 120 - 120 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 20.13 TRAIO Input Timing Diagram when VCC = 3 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 401 of 453 Unit ns ns ns VCC = 3 V R8C/26 Group, R8C/27 Group Table 20.26 20. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 300 - 150 - 150 - - 80 0 - 70 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi Input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0 or 1 VCC = 3 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0 or 1 Figure 20.14 Table 20.27 Serial Interface Timing Diagram when VCC = 3 V External Interrupt INTi (i = 0, 1, 3) Input INTi input "H" width Standard Min. Max. - 380(1) INTi input "L" width 380(2) Symbol tW(INH) tW(INL) Parameter Unit - ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 3 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 20.15 External Interrupt INTi Input Timing Diagram when VCC = 3 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 402 of 453 R8C/26 Group, R8C/27 Group Table 20.28 Electrical Characteristics (5) [VCC = 2.2 V] Symbol VOH 20. Electrical Characteristics Parameter Output "H" voltage Except P1_0 to P1_7, XOUT P1_0 to P1_7 Output "L" voltage IIH IIL RPULLUP RfXIN RfXCIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback resistance Feedback resistance RAM hold voltage Max. VCC V - VCC V IOH = -1 mA VCC - 0.5 - VCC V IOH = -0.1 mA VCC - 0.5 - VCC V IOH = -50 A VCC - 0.5 - VCC V - - 0.5 V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 2 mA - - 0.5 V IOL = 1 mA - - 0.5 V IOL = 0.1 mA - - 0.5 V IOL = 50 A - - 0.5 V INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD1, CLK0, CLK1, SSI, SCL, SDA, SSO 0.05 0.3 - V RESET 0.05 0.15 - V - - - 100 - - 1.8 200 5 35 - 4.0 -4.0 600 - - - A - VI = 2.2 V VI = 0 V VI = 0 V XIN XCIN During stop mode NOTE: 1. VCC = 2.2 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 5 MHz, unless otherwise specified. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Unit VCC - 0.5 Except P1_0 to P1_7, XOUT P1_0 to P1_7 Hysteresis Standard Typ. - IOH = -2 mA XOUT VT+-VT- IOH = -1 mA Min. VCC - 0.5 Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 1 mA XOUT VOL Condition Page 403 of 453 A k M M V R8C/26 Group, R8C/27 Group Table 20.29 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (6) [Vcc = 2.2 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 2.2 to 2.7 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Low-speed clock mode Wait mode Stop mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN = 5 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 5 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 5 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 5 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz Program operation on RAM Flash memory off, FMSTP = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (high drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator off XCIN clock oscillator on = 32 kHz (low drive) While a WAIT instruction is executed VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 404 of 453 Min. - Standard Typ. Max. 3.5 - Unit mA - 1.5 - mA - 3.5 - mA - 1.5 - mA - 100 230 A - 100 230 A - 25 - A - 22 60 A - 20 55 A - 3.0 - A - 1.8 - A - 0.7 3.0 A - 1.1 - A R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Timing requirements (Unless Otherwise Specified: VCC = 2.2 V, VSS = 0 V at Topr = 25C) [VCC = 2.2 V] Table 20.30 XIN Input, XCIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) tc(XCIN) tWH(XCIN) tWL(XCIN) Standard Min. Max. 200 - 90 - 90 - 14 - 7 - 7 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width XCIN input cycle time XCIN input "H" width XCIN input "L" width tC(XIN) Unit ns ns ns s s s VCC = 2.2 V tWH(XIN) XIN input tWL(XIN) XIN Input and XCIN Input Timing Diagram when VCC = 2.2 V Figure 20.16 Table 20.31 TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 500 - 200 - 200 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 20.17 TRAIO Input Timing Diagram when VCC = 2.2 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 405 of 453 Unit ns ns ns VCC = 2.2 V R8C/26 Group, R8C/27 Group Table 20.32 20. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 800 - 400 - 400 - - 200 0 - 150 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0 or 1 VCC = 2.2 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0 or 1 Figure 20.18 Table 20.33 Serial Interface Timing Diagram when VCC = 2.2 V External Interrupt INTi (i = 0, 1, 3) Input tW(INH) INTi input "H" width Standard Min. Max. (1) - 1000 tW(INL) INTi input "L" width 1000(2) Symbol Parameter - Unit ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 2.2 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 20.19 External Interrupt INTi Input Timing Diagram when VCC = 2.2 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 406 of 453 R8C/26 Group, R8C/27 Group 20.2 20. Electrical Characteristics J, K Version Table 20.34 Absolute Maximum Ratings Symbol VCC/AVCC VI VO Pd Parameter Supply voltage Input voltage Output voltage Power dissipation Topr Operating ambient temperature Tstg Storage temperature Table 20.35 IOH(peak) IOH(avg) IOL(sum) IOL(peak) IOL(avg) f(XIN) - -40 C Topr 85 C 85 C Topr 125 C Rated Value -0.3 to 6.5 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 300 125 -40 to 85 (J version) / -40 to 125 (K version) -65 to 150 Unit V V V mW mW C C Recommended Operating Conditions Symbol VCC/AVCC VSS/AVSS VIH VIL IOH(sum) Condition Parameter Supply voltage Supply voltage Input "H" voltage Input "L" voltage Peak sum output Sum of all pins "H" current IOH(peak) Peak output "H" current Average output "H" current Peak sum output Sum of all pins "L" currents IOL(peak) Peak output "L" currents Average output "L" current XIN clock input oscillation frequency System clock OCD2 = 0 XlN clock selected OCD2 = 1 On-chip oscillator clock selected Conditions 3.0 V VCC 5.5 V (other than K version) 3.0 V VCC 5.5 V (K version) 2.7 V VCC < 3.0 V 3.0 V VCC 5.5 V (other than K version) 3.0 V VCC 5.5 V (K version) 2.7 V VCC < 3.0 V FRA01 = 0 Low-speed on-chip oscillator clock selected FRA01 = 1 High-speed on-chip oscillator clock selected (other than K version) FRA01 = 1 High-speed on-chip oscillator clock selected Min. 2.7 - 0.8 VCC 0 - Standard Typ. - 0 - - - Max. 5.5 - VCC 0.2 VCC -60 - - -10 mA - - -5 mA - - 60 mA - - 10 mA - - 5 mA 0 - 20 MHz 0 0 0 - 16 10 20 MHz MHz MHz 0 0 - - 125 16 10 - MHz MHz kHz - - 20 MHz - - 10 MHz - - - NOTES: 1. VCC = 2.7 to 5.5 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. The average output current indicates the average value of current measured during 100 ms. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 407 of 453 Unit V V V V mA R8C/26 Group, R8C/27 Group Table 20.36 A/D Converter Characteristics Symbol - - Rladder tconv Vref VIA - 20. Electrical Characteristics Parameter Resolution Absolute accuracy Conditions Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 3.3 V AD = 10 MHz, Vref = AVCC = 3.3 V Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V 10-bit mode 8-bit mode 10-bit mode 8-bit mode Resistor ladder Conversion time 10-bit mode 8-bit mode Reference voltage Analog input voltage(2) A/D operating Without sample and hold clock frequency With sample and hold Min. - - - - - 10 3.3 2.8 2.7 0 0.25 1 Standard Typ. Max. - 10 - 3 - 2 - 5 - 2 - 40 - - - - - AVCC - AVCC - - 10 10 Unit Bits LSB LSB LSB LSB k s s V V MHz MHz NOTES: 1. AVCC = 2.7 to 5.5 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in 8-bit mode. P0 P1 P3 30pF P4 P5 Figure 20.20 Ports P0, P1, and P3 to P5 Timing Measurement Circuit Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 408 of 453 R8C/26 Group, R8C/27 Group Table 20.37 Flash Memory (Program ROM) Electrical Characteristics Symbol - - Parameter Program/erase endurance(2) - Byte program time Block erase time Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature - Data hold time(7) - td(SR-SUS) - - - - - 20. Electrical Characteristics Conditions Min. Standard Typ. - Unit Max. - times R8C/26 Group 100(3) R8C/27 Group 1,000(3) - - - - - times 50 0.4 - s 650 - 400 9 97 + CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.7 0 20 - 3 + CPU clock x 4 cycles 5.5 5.5 60 - Ambient temperature = 55C - - - s s V V C year NOTES: 1. VCC = 2.7 to 5.5 V at Topr = 0 to 60C, unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 100 or 1,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. It is also advisable to retain data on the erasure endurance of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 409 of 453 R8C/26 Group, R8C/27 Group Table 20.38 Flash Memory (Data flash Block A, Block B) Electrical Characteristics(4) Symbol - - - - - td(SR-SUS) - - - - - - - 20. Electrical Characteristics Parameter Conditions Program/erase endurance(2) Byte program time (program/erase endurance 1,000 times) Byte program time (program/erase endurance > 1,000 times) Block erase time (program/erase endurance 1,000 times) Block erase time (program/erase endurance > 1,000 times) Data hold Ambient temperature = 55C Standard Typ. - Unit Max. - times 50 400 s - 65 - s - 0.2 9 s - 0.3 - s - - s 650 - 97 + CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.7 -40 - 3 + CPU clock x 4 cycles 5.5 5.5 20 - 10,000(3) - Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature time(9) Min. - - 85(8) - V V C year NOTES: 1. VCC = 2.7 to 5.5 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. Standard of block A and block B when program and erase endurance exceeds 1,000 times. Byte program time to 1,000 times is the same as that in program ROM. 5. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. In addition, averaging the erasure endurance between blocks A and B can further reduce the actual erasure endurance. It is also advisable to retain data on the erasure endurance of each block and limit the number of erase operations to a certain number. 6. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 7. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 8. 125C for K version. 9. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 410 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Suspend request (maskable interrupt request) FMR46 Clock-dependent time Fixed time Access restart td(SR-SUS) Figure 20.21 Table 20.39 Time delay until Suspend Voltage Detection 1 Circuit Electrical Characteristics Symbol Parameter Vdet1 Voltage detection level(2, 4) td(Vdet1-A) Voltage monitor 1 reset generation time(5) Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(3) MCU operating voltage minimum value - td(E-A) Vccmin Condition VCA26 = 1, VCC = 5.0 V Min. 2.70 Standard Typ. Max. 2.85 3.0 Unit V - 40 200 s - 0.6 - - 100 A - 2.70 - - V s NOTES: 1. The measurement condition is VCC = 2.7 to 5.5 V and Topr = -40 to 85C (J version) / -40 to 125C (K version). 2. Hold Vdet2 > Vdet1. 3. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA26 bit in the VCA2 register to 0. 4. This parameter shows the voltage detection level when the power supply drops. The voltage detection level when the power supply rises is higher than the voltage detection level when the power supply drops by approximately 0.1 V. 5. Time until the voltage monitor 1 reset is generated after the voltage passes Vdet1 when VCC falls. When using the digital filter, its sampling time is added to td(Vdet1-A). When using the voltage monitor 1 reset, maintain this time until VCC = 2.0 V after the voltage passes Vdet1 when the power supply falls. Table 20.40 Voltage Detection 2 Circuit Electrical Characteristics Symbol Vdet2 td(Vdet2-A) - td(E-A) Parameter Voltage detection level(2) Voltage monitor 2 reset/interrupt request generation time(3, 5) Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(4) Condition VCA27 = 1, VCC = 5.0 V Min. 3.3 Standard Typ. Max. 3.6 3.9 Unit V - 40 200 s - 0.6 - - 100 A - s NOTES: 1. The measurement condition is VCC = 2.7 to 5.5 V and Topr = -40 to 85C (J version) / -40 to 125C (K version). 2. Hold Vdet2 > Vdet1. 3. Time until the voltage monitor 2 reset/interrupt request is generated after the voltage passes Vdet2. 4. Necessary time until the voltage detection circuit operates after setting to 1 again after setting the VCA27 bit in the VCA2 register to 0. 5. When using the digital filter, its sampling time is added to td(Vdet2-A). When using the voltage monitor 2 reset, maintain this time until VCC = 2.0 V after the voltage passes Vdet2 when the power supply falls. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 411 of 453 R8C/26 Group, R8C/27 Group Power-on Reset Circuit, Voltage Monitor 1 Reset Electrical Characteristics(3) Table 20.41 Symbol Vpor1 20. Electrical Characteristics trth Standard Typ. - Max. 0.1 0 - Vdet1 VCC 3.6 V 20(2) - - mV/msec VCC > 3.6 V 20(2) - 2,000 mV/msec Condition Power-on reset valid voltage(4) Power-on reset or voltage monitor 1 reset valid voltage External power VCC rise gradient Vpor2 Min. - Parameter Unit V V NOTES: 1. The measurement condition is Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. This condition (the minimum value of external power VCC rise gradient) does not apply if Vpor2 1.0 V. 3. To use the power-on reset function, enable voltage monitor 1 reset by setting the LVD1ON bit in the OFS register to 0, the VW1C0 and VW1C6 bits in the VW1C register to 1 respectively, and the VCA26 bit in the VCA2 register to 1. 4. tw(por1) indicates the duration the external power VCC must be held below the effective voltage (Vpor1) to enable a power on reset. When turning on the power for the first time, maintain tw(por1) for 30 s or more if -20C Topr 125C, maintain tw(por1) for 3,000 s or more if -40C Topr < -20C. V det1 (3) V det1 (3) trth trth 2.0 V External power VCC td(Vdet1-A) V por2 V por1 tw(por1) Sampling time(1, 2) Internal reset signal ("L" valid) 1 fOCO-S x 32 1 fOCO-S x 32 NOTES: 1. When using the voltage monitor 1 digital filter, ensure VCC is 2.0 V or higher during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. V det1 indicates the voltage detection level of the voltage detection 1 circuit. Refer to 6. Voltage Detection Circuit for details. Figure 20.22 Reset Circuit Electrical Characteristics Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 412 of 453 R8C/26 Group, R8C/27 Group Table 20.42 20. Electrical Characteristics High-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter fOCO40M High-speed on-chip oscillator frequency temperature * supply voltage dependence - Value in FRA1 register after reset Oscillation frequency adjustment unit of highspeed on-chip oscillator Oscillation stability time Self power consumption at oscillation - - - Condition VCC = 4.75 to 5.25 V 0C Topr 60C(2) VCC = 3.0 to 5.5 V -20C Topr 85C(2) VCC = 3.0 to 5.5 V -40C Topr 85C(2) VCC = 3.0 to 5.5 V -40C Topr 125C(2) VCC = 2.7 to 5.5 V -40C Topr 125C(2) Adjust FRA1 register (value after reset) to -1 Min. 39.2 Standard Typ. 40 Max. 40.8 MHz 38.8 40 41.2 MHz 38.4 40 41.6 MHz 38 40 42 MHz 37.6 40 42.4 MHz 08h - - +0.3 F7h - - MHz - 10 400 100 - A VCC = 5.0 V, Topr = 25C - Unit s NOTES: 1. VCC = 2.7 to 5.5 V, Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. These standard values show when the FRA1 register value after reset is assumed. Table 20.43 Low-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter fOCO-S - - Low-speed on-chip oscillator frequency Oscillation stability time Self power consumption at oscillation Condition VCC = 5.0 V, Topr = 25C Standard Typ. 125 10 15 Min. 40 - - Max. 250 100 - Unit kHz s A NOTE: 1. VCC = 2.7 to 5.5 V, Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. Table 20.44 Power Supply Circuit Timing Characteristics Symbol Parameter td(P-R) Time for internal power supply stabilization during power-on(2) td(R-S) STOP exit time(3) Condition NOTES: 1. The measurement condition is VCC = 2.7 to 5.5 V and Topr = 25C. 2. Waiting time until the internal power supply generation circuit stabilizes during power-on. 3. Time until system clock supply starts after the interrupt is acknowledged to exit stop mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 413 of 453 Min. 1 - Standard Typ. Max. - 2000 - 150 Unit s s R8C/26 Group, R8C/27 Group Table 20.45 Symbol Timing Requirements of Clock Synchronous Serial I/O with Chip Select(1) Parameter tSUCYC SSCK clock cycle time tHI tLO tRISE SSCK clock "H" width SSCK clock "L" width SSCK clock rising time tFALL 20. Electrical Characteristics SSCK clock falling time Conditions Standard Typ. - - Unit Max. - - - - - - - 100 1 - 1 - - tCYC(2) s ns - - tCYC(2) Slave 1tCYC + 50 - - ns Slave 1tCYC + 50 - - ns - - 1 - - - - 1.5tCYC + 100 1.5tCYC + 100 tCYC(2) ns ns Master Slave Master Slave SSO, SSI data input setup time SSO, SSI data input hold time tLEAD SCS setup time tOD SCS hold time SSO, SSI data output delay time tSA tOR SSI slave access time SSI slave out open time - 0.6 0.6 1 1 1 NOTES: 1. VCC = 2.7 to 5.5 V, VSS = 0 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. 1tCYC = 1/f1(s) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 tCYC(2) tSUCYC tSUCYC 0.4 0.4 - tSU tH tLAG Min. 4 Page 414 of 453 tCYC(2) s R8C/26 Group, R8C/27 Group 20. Electrical Characteristics 4-Wire Bus Communication Mode, Master, CPHS = 1 VIH or VOH SCS (output) VIH or VOH tHI tFALL tRISE SSCK (output) (CPOS = 1) tLO tHI SSCK (output) (CPOS = 0) tLO tSUCYC SSO (output) tOD SSI (input) tSU tH 4-Wire Bus Communication Mode, Master, CPHS = 0 VIH or VOH SCS (output) VIH or VOH tHI tFALL tRISE SSCK (output) (CPOS = 1) tLO tHI SSCK (output) (CPOS = 0) tLO tSUCYC SSO (output) tOD SSI (input) tSU tH CPHS, CPOS: Bits in SSMR register Figure 20.23 I/O Timing of Clock Synchronous Serial I/O with Chip Select (Master) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 415 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics 4-Wire Bus Communication Mode, Slave, CPHS = 1 VIH or VOH SCS (input) VIH or VOH tLEAD tHI tFALL tRISE tLAG SSCK (input) (CPOS = 1) tLO tHI SSCK (input) (CPOS = 0) tLO tSUCYC SSO (input) tSU tH SSI (output) tSA tOD tOR 4-Wire Bus Communication Mode, Slave, CPHS = 0 VIH or VOH SCS (input) VIH or VOH tLEAD tHI tFALL tRISE tLAG SSCK (input) (CPOS = 1) tLO tHI SSCK (input) (CPOS = 0) tLO tSUCYC SSO (input) tSU tH SSI (output) tSA tOD tOR CPHS, CPOS: Bits in SSMR register Figure 20.24 I/O Timing of Clock Synchronous Serial I/O with Chip Select (Slave) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 416 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics tHI VIH or VOH SSCK VIH or VOH tLO tSUCYC SSO (output) tOD SSI (input) tSU Figure 20.25 tH I/O Timing of Clock Synchronous Serial I/O with Chip Select (Clock Synchronous Communication Mode) Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 417 of 453 R8C/26 Group, R8C/27 Group Table 20.46 20. Electrical Characteristics Timing Requirements of I2C bus Interface(1) tSCL SCL input cycle time tSCLH SCL input "H" width Standard Typ. - 12tCYC + 600(2) - 3tCYC + 300(2) tSCLL SCL input "L" width 500(2) tsf tSP SCL, SDA input fall time SCL, SDA input spike pulse rejection time tBUF SDA input bus-free time 5tCYC(2) - 1tCYC(2) - tSTAH Start condition input hold time 3tCYC(2) - - ns tSTAS Retransmit start condition input setup time 3tCYC(2) - - ns tSTOP Stop condition input setup time 3tCYC(2) - - ns tSDAS Data input setup time - - ns tSDAH Data input hold time 1tCYC + 20(2) 0 - - ns Symbol Parameter Condition Min. 5tCYC + - - Unit Max. - ns - ns - ns - 300 - ns ns - NOTES: 1. VCC = 2.7 to 5.5 V, VSS = 0 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified. 2. 1tCYC = 1/f1(s) VIH SDA VIL tBUF tSTAH tSCLH tSTAS tSP tSTOP SCL P(2) S(1) tsf Sr(3) tSCLL tsr tSCL NOTES: 1. Start condition 2. Stop condition 3. Retransmit start condition Figure 20.26 I/O Timing of I2C bus Interface Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 418 of 453 P(2) tSDAS tSDAH ns R8C/26 Group, R8C/27 Group Table 20.47 Electrical Characteristics (1) [VCC = 5 V] Symbol VOH Parameter Output "H" voltage Except XOUT XOUT VOL Output "L" voltage Except XOUT XOUT VT+-VT- 20. Electrical Characteristics Hysteresis Condition IOH = -5 mA IOH = -200 A Drive capacity HIGH Drive capacity LOW IOL = 5 mA IOL = 200 A Drive capacity HIGH Drive capacity LOW INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD1, CLK0, CLK1, SSI, SCL, SDA, SSO RESET IIH IIL RPULLUP RfXIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback resistance RAM hold voltage VI = 5 V, VCC = 5V VI = 0 V, VCC = 5V VI = 0 V, VCC = 5V XIN During stop mode IOH = -1 mA IOH = -500 A IOL = 1 mA IOL = 500 A Min. VCC - 2.0 VCC - 0.3 VCC - 2.0 VCC - 2.0 - - - - 0.1 Standard Typ. - - - - - - - - 0.5 Max. VCC VCC VCC VCC 2.0 0.45 2.0 2.0 - Unit V V V V V V V V V 0.1 1.0 - V - - - 30 - 50 1.0 5.0 -5.0 167 - A - A k M 2.0 - - V NOTE: 1. VCC = 4.2 to 5.5 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), f(XIN) = 20 MHz, unless otherwise specified. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 419 of 453 R8C/26 Group, R8C/27 Group Table 20.48 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (2) [Vcc = 5 V] (Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 3.3 to 5.5 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Wait mode Stop mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division Min. - Standard Typ. Max. 10 17 Unit mA XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division - 9 15 mA XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division - 6 - mA XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 5 - mA XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 4 - mA XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 2.5 - mA XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz (J version) Low-speed on-chip oscillator on = 125 kHz No division - 10 15 mA XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz (J version) Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 4 - mA XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division - 5.5 10 mA XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 2.5 - mA XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 - 130 300 A XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 - 25 75 A XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 - 23 60 A XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 - 0.8 3.0 A XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 - 1.2 - A XIN clock off, Topr = 125C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 - 4.0 - A Page 420 of 453 R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Timing Requirements (Unless Otherwise Specified: VCC = 5 V, VSS = 0 V at Topr = 25C) [VCC = 5 V] Table 20.49 XIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) Standard Min. Max. 50 - 25 - 25 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width tC(XIN) Unit ns ns ns VCC = 5 V tWH(XIN) XIN input tWL(XIN) Figure 20.27 Table 20.50 XIN Input Timing Diagram when VCC = 5 V TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 100 - 40 - 40 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 20.28 TRAIO Input Timing Diagram when VCC = 5 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 421 of 453 Unit ns ns ns VCC = 5 V R8C/26 Group, R8C/27 Group Table 20.51 20. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 200 - 100 - 100 - - 50 0 - 50 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0 or 1 VCC = 5 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0 or 1 Figure 20.29 Table 20.52 Serial Interface Timing Diagram when VCC = 5 V External Interrupt INTi (i = 0, 1, 3) Input INTi input "H" width Standard Min. Max. - 250(1) INTi input "L" width 250(2) Symbol tW(INH) tW(INL) Parameter - Unit ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 5 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 20.30 External Interrupt INTi Input Timing Diagram when VCC = 5 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 422 of 453 R8C/26 Group, R8C/27 Group Table 20.53 Electrical Characteristics (3) [VCC = 3 V] Symbol VOH VOL VT+-VT- IIH IIL RPULLUP RfXIN VRAM 20. Electrical Characteristics Parameter Output "H" voltage Except XOUT XOUT Output "L" voltage Input "H" current Input "L" current Pull-up resistance Feedback resistance RAM hold voltage IOH = -1 mA Drive capacity HIGH Drive capacity LOW IOL = 1 mA Drive capacity HIGH Drive capacity LOW Standard Typ. - - Max. VCC VCC Unit IOH = -0.1 mA Min. VCC - 0.5 VCC - 0.5 IOH = -50 A VCC - 0.5 - VCC V V V - - IOL = 0.1 mA - - 0.5 0.5 V V IOL = 50 A - - 0.5 V INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD1, CLK0,CLK1, SSI, SCL, SDA, SSO 0.1 0.3 - V RESET 0.1 0.4 - V - - - 66 - 2.0 160 3.0 - 4.0 -4.0 500 - - A - Except XOUT XOUT Hysteresis Condition VI = 3 V, VCC = 3V VI = 0 V, VCC = 3V VI = 0 V, VCC = 3V XIN During stop mode A k M V NOTE: 1. VCC = 2.7 to 3.3 V at Topr = -40 to 85C (J version) / -40 to 125C (K version), f(XIN) = 10 MHz, unless otherwise specified. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 423 of 453 R8C/26 Group, R8C/27 Group Table 20.54 Symbol ICC 20. Electrical Characteristics Electrical Characteristics (4) [Vcc = 3 V] (Topr = -40 to 85C (J version) / -40 to 125C (K version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 2.7 to 3.3 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Wait mode Stop mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 125C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 424 of 453 Min. - Standard Typ. Max. 6 - Unit mA - 2 - mA - 5 9 mA - 2 - mA - 130 300 A - 25 70 A - 23 55 A - 0.7 3.0 A - 1.1 - A - 3.8 - A R8C/26 Group, R8C/27 Group 20. Electrical Characteristics Timing requirements (Unless Otherwise Specified: VCC = 3 V, VSS = 0 V at Topr = 25C) [VCC = 3 V] XIN Input Table 20.55 Symbol tc(XIN) tWH(XIN) tWL(XIN) Standard Min. Max. 100 - 40 - 40 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width tC(XIN) Unit ns ns ns VCC = 3 V tWH(XIN) XIN input tWL(XIN) Figure 20.31 XIN Input Timing Diagram when VCC = 3 V Table 20.56 TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 300 - 120 - 120 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 20.32 TRAIO Input Timing Diagram when VCC = 3 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 425 of 453 Unit ns ns ns VCC = 3 V R8C/26 Group, R8C/27 Group Table 20.57 20. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 300 - 150 - 150 - - 80 0 - 70 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi Input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0 or 1 VCC = 3 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0 or 1 Figure 20.33 Table 20.58 Serial Interface Timing Diagram when VCC = 3 V External Interrupt INTi (i = 0, 1, 3) Input INTi input "H" width Standard Min. Max. - 380(1) INTi input "L" width 380(2) Symbol tW(INH) tW(INL) Parameter Unit - ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 3 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 20.34 External Interrupt INTi Input Timing Diagram when VCC = 3 V Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 426 of 453 R8C/26 Group, R8C/27 Group 21. Usage Notes 21. Usage Notes 21.1 Notes on Clock Generation Circuit 21.1.1 Stop Mode When entering stop mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and the CM10 bit in the CM1 register to 1 (stop mode). An instruction queue pre-reads 4 bytes from the instruction which sets the CM10 bit to 1 (stop mode) and the program stops. Insert at least 4 NOP instructions following the JMP.B instruction after the instruction which sets the CM10 bit to 1. * Program example to enter stop mode BCLR BSET FSET BSET JMP.B LABEL_001 : NOP NOP NOP NOP 21.1.2 1,FMR0 0,PRCR I 0,CM1 LABEL_001 ; CPU rewrite mode disabled ; Protect disabled ; Enable interrupt ; Stop mode Wait Mode When entering wait mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and execute the WAIT instruction. An instruction queue pre-reads 4 bytes from the WAIT instruction and the program stops. Insert at least 4 NOP instructions after the WAIT instruction. * Program example to execute the WAIT instruction BCLR 1,FMR0 FSET I WAIT NOP NOP NOP NOP 21.1.3 ; CPU rewrite mode disabled ; Enable interrupt ; Wait mode Oscillation Stop Detection Function Since the oscillation stop detection function cannot be used if the XIN clock frequency is 2 MHz or below, set bits OCD1 to OCD0 to 00b. 21.1.4 Oscillation Circuit Constants Ask the manufacturer of the oscillator to specify the best oscillation circuit constants for your system. To use this MCU with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 427 of 453 R8C/26 Group, R8C/27 Group 21.2 21. Usage Notes Notes on Interrupts 21.2.1 Reading Address 00000h Do not read address 00000h by a program. When a maskable interrupt request is acknowledged, the CPU reads interrupt information (interrupt number and interrupt request level) from 00000h in the interrupt sequence. At this time, the acknowledged interrupt IR bit is set to 0. If address 00000h is read by a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is set to 0. This may cause the interrupt to be canceled, or an unexpected interrupt to be generated. 21.2.2 SP Setting Set any value in the SP before an interrupt is acknowledged. The SP is set to 0000h after reset. Therefore, if an interrupt is acknowledged before setting a value in the SP, the program may run out of control. 21.2.3 External Interrupt and Key Input Interrupt Either "L" level or an "H" level of width shown in the Electrical Characteristics is necessary for the signal input to pins INT0, INT1, INT3 and pins KI0 to KI3, regardless of the CPU clock. For details, refer to Table 20.21 (VCC = 5V), Table 20.27 (VCC = 3V), Table 20.33 (VCC = 2.2V), Table 20.52 (VCC = 5V), Table 20.58 (VCC = 3V) External Interrupt INTi (i = 0, 1, 3) Input. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 428 of 453 R8C/26 Group, R8C/27 Group 21.2.4 21. Usage Notes Changing Interrupt Sources The IR bit in the interrupt control register may be set to 1 (interrupt requested) when the interrupt source changes. When using an interrupt, set the IR bit to 0 (no interrupt requested) after changing the interrupt source. In addition, changes of interrupt sources include all factors that change the interrupt sources assigned to individual software interrupt numbers, polarities, and timing. Therefore, if a mode change of a peripheral function involves interrupt sources, edge polarities, and timing, set the IR bit to 0 (no interrupt requested) after the change. Refer to the individual peripheral function for its related interrupts. Figure 21.1 shows an Example of Procedure for Changing Interrupt Sources. Interrupt source change Disable interrupts(2, 3) Change interrupt source (including mode of peripheral function) Set the IR bit to 0 (interrupt not requested) using the MOV instruction(3) Enable interrupts (2, 3) Change completed IR bit: The interrupt control register bit of an interrupt whose source is changed. NOTES: 1. Execute the above settings individually. Do not execute two or more settings at once (by one instruction). 2. To prevent interrupt requests from being generated, disable the peripheral function before changing the interrupt source. In this case, use the I flag if all maskable interrupts can be disabled. If all maskable interrupts cannot be disabled, use bits ILVL0 to ILVL2 of the interrupt whose source is changed. 3. Refer to 12.6.5 Changing Interrupt Control Register Contents for the instructions to be used and usage notes. Figure 21.1 Example of Procedure for Changing Interrupt Sources Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 429 of 453 R8C/26 Group, R8C/27 Group 21.2.5 21. Usage Notes Changing Interrupt Control Register Contents (a) The contents of an interrupt control register can only be changed while no interrupt requests corresponding to that register are generated. If interrupt requests may be generated, disable interrupts before changing the interrupt control register contents. (b) When changing the contents of an interrupt control register after disabling interrupts, be careful to choose appropriate instructions. Changing any bit other than IR bit If an interrupt request corresponding to a register is generated while executing the instruction, the IR bit may not be set to 1 (interrupt requested), and the interrupt request may be ignored. If this causes a problem, use the following instructions to change the register: AND, OR, BCLR, BSET Changing IR bit If the IR bit is set to 0 (interrupt not requested), it may not be set to 0 depending on the instruction used. Therefore, use the MOV instruction to set the IR bit to 0. (c) When disabling interrupts using the I flag, set the I flag as shown in the sample programs below. Refer to (b) regarding changing the contents of interrupt control registers by the sample programs. Sample programs 1 to 3 are for preventing the I flag from being set to 1 (interrupts enabled) before the interrupt control register is changed for reasons of the internal bus or the instruction queue buffer. Example 1: Use NOP instructions to prevent I flag from being set to 1 before interrupt control register is changed INT_SWITCH1: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h NOP ; NOP FSET I ; Enable interrupts Example 2: Use dummy read to delay FSET instruction INT_SWITCH2: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h MOV.W MEM,R0 ; Dummy read FSET I ; Enable interrupts Example 3: Use POPC instruction to change I flag INT_SWITCH3: PUSHC FLG FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h POPC FLG ; Enable interrupts Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 430 of 453 R8C/26 Group, R8C/27 Group 21.3 21.3.1 21. Usage Notes Notes on Timers Notes on Timer RA * Timer RA stops counting after a reset. Set the values in the timer RA and timer RA prescalers before the count starts. * Even if the prescaler and timer RA are read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In pulse period measurement mode, bits TEDGF and TUNDF in the TRACR register can be set to 0 by writing 0 to these bits by a program. However, these bits remain unchanged if 1 is written. When using the READ-MODIFY-WRITE instruction for the TRACR register, the TEDGF or TUNDF bit may be set to 0 although these bits are set to 1 while the instruction is being executed. In this case, write 1 to the TEDGF or TUNDF bit which is not supposed to be set to 0 with the MOV instruction. * When changing to pulse period measurement mode from another mode, the contents of bits TEDGF and TUNDF are undefined. Write 0 to bits TEDGF and TUNDF before the count starts. * The TEDGF bit may be set to 1 by the first timer RA prescaler underflow generated after the count starts. * When using the pulse period measurement mode, leave two or more periods of the timer RA prescaler immediately after the count starts, then set the TEDGF bit to 0. * The TCSTF bit retains 0 (count stops) for 0 to 1 cycle of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. Timer RA starts counting at the first valid edge of the count source after The TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 0 to 1 cycle of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RA counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RA: TRACR, TRAIOC, TRAMR, TRAPRE, and TRA. * When the TRAPRE register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source clock for each write interval. * When the TRA register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 431 of 453 R8C/26 Group, R8C/27 Group 21.3.2 21. Usage Notes Notes on Timer RB * Timer RB stops counting after a reset. Set the values in the timer RB and timer RB prescalers before the count starts. * Even if the prescaler and timer RB is read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In programmable one-shot generation mode and programmable wait one-shot generation mode, when setting the TSTART bit in the TRBCR register to 0, 0 (stops counting) or setting the TOSSP bit in the TRBOCR register to 1 (stops one-shot), the timer reloads the value of reload register and stops. Therefore, in programmable one-shot generation mode and programmable wait one-shot generation mode, read the timer count value before the timer stops. * The TCSTF bit remains 0 (count stops) for 1 to 2 cycles of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RB(1)other than the TCSTF bit. Timer RB starts counting at the first valid edge of the count source after the TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 1 to 2 cycles of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RB counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RB: TRBCR, TRBOCR, TRBIOC, TRBMR, TRBPRE, TRBSC, and TRBPR. * If the TSTOP bit in the TRBCR register is set to 1 during timer operation, timer RB stops immediately. * If 1 is written to the TOSST or TOSSP bit in the TRBOCR register, the value of the TOSSTF bit changes after one or two cycles of the count source have elapsed. If the TOSSP bit is written to 1 during the period between when the TOSST bit is written to 1 and when the TOSSTF bit is set to 1, the TOSSTF bit may be set to either 0 or 1 depending on the content state. Likewise, if the TOSST bit is written to 1 during the period between when the TOSSP bit is written to 1 and when the TOSSTF bit is set to 0, the TOSSTF bit may be set to either 0 or 1. 21.3.2.1 Timer mode The following workaround should be performed in timer mode. To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 432 of 453 R8C/26 Group, R8C/27 Group 21.3.2.2 21. Usage Notes Programmable waveform generation mode The following three workarounds should be performed in programmable waveform generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) To change registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), synchronize the TRBO output cycle using a timer RB interrupt, etc. This operation should be preformed only once in the same output cycle. Also, make sure that writing to the TRBPR register does not occur during period A shown in Figures 21.2 and 21.3. The following shows the detailed workaround examples. * Workaround example (a): As shown in Figure 21.2, write to registers TRBSC and TRBPR in the timer RB interrupt routine. These write operations must be completed by the beginning of period A. Period A Count source/ prescaler underflow signal TRBO pin output IR bit in TRBIC register Primary period (a) Interrupt request is acknowledged Secondary period Ensure sufficient time (b) Interrupt request is generated Interrupt Instruction in sequence interrupt routine Set the secondary and then the primary register immediately (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (assuming no wait states and that a register is set as the divisor). (b) 20 cycles. 21 cycles for address match and single-step interrupts. Figure 21.2 Workaround Example (a) When Timer RB interrupt is Used Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 433 of 453 R8C/26 Group, R8C/27 Group 21. Usage Notes * Workaround example (b): As shown in Figure 21.3 detect the start of the primary period by the TRBO pin output level and write to registers TRBSC and TRBPR. These write operations must be completed by the beginning of period A. If the port register's bit value is read after the port direction register's bit corresponding to the TRBO pin is set to 0 (input mode), the read value indicates the TRBO pin output value. Period A Count source/ prescaler underflow signal TRBO pin output Read value of the port register's bit corresponding to the TRBO pin (when the bit in the port direction register is set to 0) Primary period Secondary period (i) (ii) (iii) Ensure sufficient time The TRBO output inversion is detected at the end of the secondary period. Figure 21.3 Upon detecting (i), set the secondary and then the primary register immediately. Workaround Example (b) When TRBO Pin Output Value is Read (3) To stop the timer counting in the primary period, use the TSTOP bit in the TRBCR register. In this case, registers TRBPRE and TRBPR are initialized and their values are set to the values after reset. 21.3.2.3 Programmable one-shot generation mode The following two workarounds should be performed in programmable one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 434 of 453 R8C/26 Group, R8C/27 Group 21.3.2.4 21. Usage Notes Programmable wait one-shot generation mode The following three workarounds should be performed in programmable wait one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. (3) Set registers TRBSC and TRBPR using the following procedure. (a) To use "INT0 pin one-shot trigger enabled" as the count start condition Set the TRBSC register and then the TRBPR register. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before trigger input from the INT0 pin. (b) To use "writing 1 to TOSST bit" as the start condition Set the TRBSC register, the TRBPR register, and then TOSST bit. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before writing to the TOSST bit. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 435 of 453 R8C/26 Group, R8C/27 Group 21.3.3 21. Usage Notes Notes on Timer RC 21.3.3.1 TRC Register * The following note applies when the CCLR bit in the TRCCR1 register is set to 1 (clear TRC register at compare match with TRCGRA register). When using a program to write a value to the TRC register while the TSTART bit in the TRCMR register is set to 1 (count starts), ensure that the write does not overlap with the timing with which the TRC register is set to 0000h. If the timing of the write to the TRC register and the setting of the TRC register to 0000h coincide, the write value will not be written to the TRC register and the TRC register will be set to 0000h. * Reading from the TRC register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.W #XXXXh, TRC ;Write JMP.B L1 ;JMP.B instruction L1: MOV.W TRC,DATA ;Read 21.3.3.2 TRCSR Register Reading from the TRCSR register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.B #XXh, TRCSR ;Write JMP.B L1 ;JMP.B instruction L1: MOV.B TRCSR,DATA ;Read 21.3.3.3 Count Source Switching * Stop the count before switching the count source. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. * After switching the count source from fOCO40M to another clock, allow a minimum of two cycles of f1 to elapse after changing the clock setting before stopping fOCO40M. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. (3) Wait for a minimum of two cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator off). 21.3.3.4 Input Capture Function * The pulse width of the input capture signal should be three cycles or more of the timer RC operation clock (refer to Table 14.11 Timer RC Operation Clock). * The value of the TRC register is transferred to the TRCGRj register one or two cycles of the timer RC operation clock after the input capture signal is input to the TRCIOj (j = A, B, C, or D) pin (when the digital filter function is not used). 21.3.3.5 TRCMR Register in PWM2 Mode When the CSEL bit in the TRCCR2 register is set to 1 (count stops at compare match with the TRCGRA register), do not set the TRCMR register at compare match timing of registers TRC and TRCGRA. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 436 of 453 R8C/26 Group, R8C/27 Group 21.3.4 21. Usage Notes Notes on Timer RE 21.3.4.1 Starting and Stopping Count Timer RE has the TSTART bit for instructing the count to start or stop, and the TCSTF bit, which indicates count start or stop. Bits TSTART and TCSTF are in the TRECR1 register. Timer RE starts counting and the TCSTF bit is set to 1 (count starts) when the TSTART bit is set to 1 (count starts). It takes up to 2 cycles of the count source until the TCSTF bit is set to 1 after setting the TSTART bit to 1. During this time, do not access registers associated with timer RE(1) other than the TCSTF bit. Also, timer RE stops counting when setting the TSTART bit to 0 (count stops) and the TCSTF bit is set to 0 (count stops). It takes the time for up to 2 cycles of the count source until the TCSTF bit is set to 0 after setting the TSTART bit to 0. During this time, do not access registers associated with timer RE other than the TCSTF bit. NOTE: 1. Registers associated with timer RE: TRESEC, TREMIN, TREHR, TREWK, TRECR1, TRECR2, and TRECSR. 21.3.4.2 Register Setting Write to the following registers or bits when timer RE is stopped. * Registers TRESEC, TREMIN, TREHR, TREWK, and TRECR2 * Bits H12_H24, PM, and INT in TRECR1 register * Bits RCS0 to RCS3 in TRECSR register Timer RE is stopped when bits TSTART and TCSTF in the TRECR1 register are set to 0 (timer RE stopped). Also, set all above-mentioned registers and bits (immediately before timer RE count starts) before setting the TRECR2 register. Figure 21.4 shows a Setting Example in Real-Time Clock Mode. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 437 of 453 R8C/26 Group, R8C/27 Group 21. Usage Notes TSTART in TRECR1 = 0 Stop timer RE operation TCSTF in TRECR1 = 0? TREIC 00h (disable timer RE interrupt) TRERST in TRECR1 = 1 Timer RE register and control circuit reset TRERST in TRECR1 = 0 Setting of registers TRECSR, TRESEC, TREMIN, TREHR, TREWK, and bits H12_H24, PM, and INT in TRECR1 register Setting of TRECR2 Select clock output Select clock source Seconds, minutes, hours, days of week, operating mode Set a.m./p.m., interrupt timing Select interrupt source Setting of TREIC (IR bit 0, select interrupt priority level) TSTART in TRECR1 = 1 Start timer RE operation TCSTF in TRECR1 = 1? Figure 21.4 Setting Example in Real-Time Clock Mode Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 438 of 453 R8C/26 Group, R8C/27 Group 21.3.4.3 21. Usage Notes Time Reading Procedure of Real-Time Clock Mode In real-time clock mode, read registers TRESEC, TREMIN, TREHR, and TREWK when time data is updated and read the PM bit in the TRECR1 register when the BSY bit is set to 0 (not while data is updated). Also, when reading several registers, an incorrect time will be read if data is updated before another register is read after reading any register. In order to prevent this, use the reading procedure shown below. * Using an interrupt Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register in the timer RE interrupt routine. * Monitoring with a program 1 Monitor the IR bit in the TREIC register with a program and read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register after the IR bit in the TREIC register is set to 1 (timer RE interrupt request generated). * Monitoring with a program 2 (1) Monitor the BSY bit. (2) Monitor until the BSY bit is set to 0 after the BSY bit is set to 1 (approximately 62.5 ms while the BSY bit is set to 1). (3) Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register after the BSY bit is set to 0. * Using read results if they are the same value twice (1) Read necessary contents of registers TRESEC, TREMIN, TREHR, and TREWK and the PM bit in the TRECR1 register. (2) Read the same register as (1) and compare the contents. (3) Recognize as the correct value if the contents match. If the contents do not match, repeat until the read contents match with the previous contents. Also, when reading several registers, read them as continuously as possible. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 439 of 453 R8C/26 Group, R8C/27 Group 21.4 21. Usage Notes Notes on Serial Interface * When reading data from the UiRB (i = 0 or 1) register either in the clock synchronous serial I/O mode or in the clock asynchronous serial I/O mode. Ensure the data is read in 16-bit units. When the high-order byte of the UiRB register is read, bits PER and FER in the UiRB register and the RI bit in the UiC1 register are set to 0. To check receive errors, read the UiRB register and then use the read data. Example (when reading receive buffer register): MOV.W 00A6H,R0 ; Read the U0RB register * When writing data to the UiTB register in the clock asynchronous serial I/O mode with 9-bit transfer data length, write data to the high-order byte first then the low-order byte, in 8-bit units. Example (when reading transmit buffer register): MOV.B #XXH,00A3H ; Write the high-order byte of U0TB register MOV.B #XXH,00A2H ; Write the low-order byte of U0TB register Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 440 of 453 R8C/26 Group, R8C/27 Group 21.5 21. Usage Notes Notes on Clock Synchronous Serial Interface 21.5.1 Notes on Clock Synchronous Serial I/O with Chip Select Set the IICSEL bit in the PMR register to 0 (select clock synchronous serial I/O with chip select function) to use the clock synchronous serial I/O with chip select function. 21.5.2 Notes on I2C bus Interface Set the IICSEL bit in the PMR register to 1 (select I2C bus interface function) to use the I2C bus interface. 21.5.2.1 Multimaster Operation The following actions must be performed to use the I2C bus interface in multimaster operation. * Transfer rate Set the transfer rate by 1/1.8 or faster than the fastest rate of the other masters. For example, if the fastest transfer rate of the other masters is set to 400 kbps, the I2C-bus transfer rate in this MCU should be set to 223 kbps (= 400/1.18) or more. * Bits MST and TRS in the ICCR1 register setting (a) Use the MOV instruction to set bits MST and TRS. (b) When arbitration is lost, confirm the contents of bits MST and TRS. If the contents are other than the MST bit set to 0 and the TRS bit set to 0 (slave receive mode), set the MST bit to 0 and the TRS bit to 0 again. 21.5.2.2 Master Receive Mode Either of the following actions must be performed to use the I2C bus interface in master receive mode. (a) In master receive mode while the RDRF bit in the ICSR register is set to 1, read the ICDRR register before the rising edge of the 8th clock. (b) In master receive mode, set the RCVD bit in the ICCR1 register to 1 (disables the next receive operation) to perform 1-byte communications. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 441 of 453 R8C/26 Group, R8C/27 Group 21.6 21. Usage Notes Notes on Hardware LIN For the time-out processing of the header and response fields, use another timer to measure the duration of time with a Synch Break detection interrupt as the starting point. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 442 of 453 R8C/26 Group, R8C/27 Group 21.7 21. Usage Notes Notes on A/D Converter * Write to each bit (other than bit 6) in the ADCON0 register, each bit in the ADCON1 register, or the SMP bit in the ADCON2 register when A/D conversion is stopped (before a trigger occurs). When the VCUT bit in the ADCON1 register is changed from 0 (VREF not connected) to 1 (VREF connected), wait for at least 1 s before starting the A/D conversion. * After changing the A/D operating mode, select an analog input pin again. * When using the one-shot mode, ensure that A/D conversion is completed before reading the AD register. The IR bit in the ADIC register or the ADST bit in the ADCON0 register can be used to determine whether A/D conversion is completed. * When using the repeat mode, select the frequency of the A/D converter operating clock AD or more for the CPU clock during A/D conversion. * If the ADST bit in the ADCON0 register is set to 0 (A/D conversion stops) by a program and A/D conversion is forcibly terminated during an A/D conversion operation, the conversion result of the A/D converter will be undefined. If the ADST bit is set to 0 by a program, do not use the value of the AD register. * Connect 0.1 F capacitor between the P4_2/VREF pin and AVSS pin. * Do not enter stop mode during A/D conversion. * Do not enter wait mode when the CM02 bit in the CM0 register is set to 1 (peripheral function clock stops in wait mode) during A/D conversion. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 443 of 453 R8C/26 Group, R8C/27 Group 21.8 21. Usage Notes Notes on Flash Memory 21.8.1 CPU Rewrite Mode 21.8.1.1 Operating Speed Before entering CPU rewrite mode (EW0 mode), select 5 MHz or below for the CPU clock using the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. This does not apply to EW1 mode. 21.8.1.2 Prohibited Instructions The following instructions cannot be used in EW0 mode because they reference internal data in flash memory: UND, INTO, and BRK. 21.8.1.3 Interrupts Table 21.1 lists the EW0 Mode Interrupts and Table 21.2 lists the EW1 Mode Interrupt. Table 21.1 Mode EW0 Mode Interrupts When Maskable Interrupt Request is Acknowledged Status EW0 During auto-erasure Any interrupt can be used by allocating a vector in RAM Auto-programming When Watchdog Timer, Oscillation Stop Detection, Voltage Monitor 1, or Voltage Monitor 2 Interrupt Request is Acknowledged Once an interrupt request is acknowledged, the auto-programming or auto-erasure is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after the fixed period and the flash memory restarts. Since the block during autoerasure or the address during autoprogramming is forcibly stopped, the normal value may not be read. Execute auto-erasure again and ensure it completes normally. Since the watchdog timer does not stop during the command operation, interrupt requests may be generated. Reset the watchdog timer regularly. NOTES: 1. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. 2. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 444 of 453 R8C/26 Group, R8C/27 Group Table 21.2 Mode 21. Usage Notes EW1 Mode Interrupt When Watchdog Timer, Oscillation Stop Detection, Voltage Monitor 1, or Voltage Monitor 2 Interrupt Request is Acknowledged Auto-erasure is suspended after Once an interrupt request is acknowledged, auto-programming or td(SR-SUS) and interrupt auto-erasure is forcibly stopped handling is executed. Autoimmediately and the flash memory is erasure can be restarted by reset. Interrupt handling starts after the setting the FMR41 bit in the FMR4 register to 0 (erase restart) fixed period and the flash memory restarts. Since the block during autoafter interrupt handling erasure or the address during autocompletes. Auto-erasure has priority and the programming is forcibly stopped, the normal value may not be read. Execute interrupt request auto-erasure again and ensure it acknowledgement is put on completes normally. standby. Interrupt handling is Since the watchdog timer does not stop executed after auto-erasure during the command operation, completes. Auto-programming is suspended interrupt requests may be generated. Reset the watchdog timer regularly after td(SR-SUS) and interrupt using the erase-suspend function. handling is executed. Auto-programming can be restarted by setting the FMR42 bit in the FMR4 register to 0 (program restart) after interrupt handling completes. Auto-programming has priority and the interrupt request acknowledgement is put on standby. Interrupt handling is executed after auto-programming completes. When Maskable Interrupt Request is Acknowledged Status EW1 During auto-erasure (erase-suspend function enabled) During auto-erasure (erase-suspend function disabled) During autoprogramming (program suspend function enabled) During autoprogramming (program suspend function disabled) NOTES: 1. Do not use the address match interrupt while a command is executing because the vector of the address match interrupt is allocated in ROM. 2. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 445 of 453 R8C/26 Group, R8C/27 Group 21.8.1.4 21. Usage Notes How to Access Write 0 before writing 1 when setting the FMR01, FMR02, or FMR11 bit to 1. Do not generate an interrupt between writing 0 and 1. 21.8.1.5 Rewriting User ROM Area In EW0 Mode, if the supply voltage drops while rewriting any block in which a rewrite control program is stored, it may not be possible to rewrite the flash memory because the rewrite control program cannot be rewritten correctly. In this case, use standard serial I/O mode. 21.8.1.6 Program Do not write additions to the already programmed address. 21.8.1.7 Entering Stop Mode or Wait Mode Do not enter stop mode or wait mode during erase-suspend. 21.8.1.8 Program and Erase Voltage for Flash Memory To perform programming and erasure, use VCC = 2.7 to 5.5 V as the supply voltage. Do not perform programming and erasure at less than 2.7 V. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 446 of 453 R8C/26 Group, R8C/27 Group 21.9 21. Usage Notes Notes on Noise 21.9.1 Inserting a Bypass Capacitor between VCC and VSS Pins as a Countermeasure against Noise and Latch-up Connect a bypass capacitor (at least 0.1 F) using the shortest and thickest write possible. 21.9.2 Countermeasures against Noise Error of Port Control Registers During rigorous noise testing or the like, external noise (mainly power supply system noise) can exceed the capacity of the MCU's internal noise control circuitry. In such cases the contents of the port related registers may be changed. As a firmware countermeasure, it is recommended that the port registers, port direction registers, and pull-up control registers be reset periodically. However, examine the control processing fully before introducing the reset routine as conflicts may be created between the reset routine and interrupt routines. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 447 of 453 R8C/26 Group, R8C/27 Group 22. Notes for On-Chip Debugger 22. Notes for On-Chip Debugger When using the on-chip debugger to develop and debug programs for the R8C/26 Group and R8C/27 Group take note of the following. (1) (2) (3) (4) (5) Do not access the registers associated with UART1. Some of the user flash memory and RAM areas are used by the on-ship debugger. These areas cannot be accessed by the user. Refer to the on-chip debugger manual for which areas are used. Do not set the address match interrupt (registers AIER, RMAD0, and RMAD1 and fixed vector tables) in a user system. Do not use the BRK instruction in a user system. Debugging is available under the condition of supply voltage VCC = 2.7 to 5.5 V. Debugging with the on-chip debugger under less than 2.7 V is not allowed. Connecting and using the on-chip debugger has some special restrictions. Refer to the on-chip debugger manual for details. Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 448 of 453 R8C/26 Group, R8C/27 Group Appendix 1. Package Dimensions Appendix 1. Package Dimensions Diagrams showing the latest package dimensions and mounting information are available in the "Packages" section of the Renesas Technology website. JEITA Package Code P-LQFP32-7x7-0.80 RENESAS Code PLQP0032GB-A Previous Code 32P6U-A MASS[Typ.] 0.2g HD *1 D 24 17 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. 16 25 bp c c1 HE *2 E b1 Reference Dimension in Millimeters Symbol 32 9 1 ZE Terminal cross section 8 ZD c A A1 F A2 Index mark L D E A2 HD HE A A1 bp b1 c c1 L1 y e Rev.2.10 Sep 26, 2008 REJ09B0278-0210 *3 Detail F bp x Page 449 of 453 e x y ZD ZE L L1 Min Nom Max 6.9 7.0 7.1 6.9 7.0 7.1 1.4 8.8 9.0 9.2 8.8 9.0 9.2 1.7 0.1 0.2 0 0.32 0.37 0.42 0.35 0.09 0.145 0.20 0.125 0 8 0.8 0.20 0.10 0.7 0.7 0.3 0.5 0.7 1.0 R8C/26 Group, R8C/27 Group Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator Appendix Figure 2.1 shows a Connection Example with M16C Flash Starter (M3A-0806) and Appendix Figure 2.2 shows a Connection Example with E8 Emulator (R0E000080KCE00). VCC 25 23 4 5 6 7 MODE 27 VSS 26 24 2 R8C/26 Group R8C/27 Group 1 3 Connect oscillation circuit (1) 28 29 RESET 30 32 31 TXD 22 21 20 19 18 17 8 16 15 14 13 12 11 9 10 10 TXD 7 VSS RXD 4 1 VCC M16C Flash Starter (M3A-0806) RXD NOTE: 1. An oscillation circuit must be connected, even when operating with the on-chip oscillator clock. Appendix Figure 2.1 Connection Example with M16C Flash Starter (M3A-0806) VCC Open collector buffer 13 12 RESET 4 5 22 21 20 19 18 17 8 15 16 14 13 11 12 9 10 8 VCC 7 MODE 10 25 14 26 23 6 4.7k 10% 27 24 2 R8C/26 Group R8C/27 Group VSS 28 30 1 3 Connect oscillation circuit(1) 29 32 31 4.7k or more User logic 7 MODE 6 4 2 VSS E8 emulator (R0E000080KCE00) Appendix Figure 2.2 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 NOTE: 1. It is not necessary to connect an oscillation circuit when operating with the on-chip oscillator clock. Connection Example with E8 Emulator (R0E000080KCE00) Page 450 of 453 R8C/26 Group, R8C/27 Group Appendix 3. Example of Oscillation Evaluation Circuit Appendix 3. Example of Oscillation Evaluation Circuit Appendix Figure 3.1 shows an Example of Oscillation Evaluation Circuit. VCC 25 26 27 28 24 2 23 R8C/26 Group R8C/27 Group 3 4 VSS 29 30 Connect oscillation circuit 31 32 RESET 1 5 6 22 21 20 19 7 18 8 17 16 15 14 13 12 11 10 9 NOTE: 1. After reset, the XIN and XCIN clocks stop. Write a program to oscillate the XIN and XCIN clocks. Appendix Figure 3.1 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Example of Oscillation Evaluation Circuit Page 451 of 453 R8C/26 Group, R8C/27 Group Index Index [A] AD ....................................................................................... 341 ADCON0 ............................................................................. 340 ADCON1 ............................................................................. 341 ADCON2 ............................................................................. 341 ADIC .................................................................................... 115 AIER .................................................................................... 130 [C] CM0 ....................................................................................... 81 CM1 ....................................................................................... 82 CPSRF .................................................................................. 86 CSPR .................................................................................. 138 [F] FMR0 .................................................................................. 361 FMR1 .................................................................................. 362 FMR4 .................................................................................. 363 FRA0 ..................................................................................... 84 FRA1 ..................................................................................... 84 FRA2 ..................................................................................... 85 FRA4 ..................................................................................... 85 FRA6 ..................................................................................... 85 FRA7 ..................................................................................... 85 [I] ICCR1 ................................................................................. 293 ICCR2 ................................................................................. 294 ICDRR ................................................................................. 298 ICDRS ................................................................................. 298 ICDRT ................................................................................. 298 ICIER ................................................................................... 296 ICMR ................................................................................... 295 ICSR .................................................................................... 297 IICIC .................................................................................... 116 INT0IC ................................................................................. 117 INT1IC ................................................................................. 117 INT3IC ................................................................................. 117 INTEN ................................................................................. 124 INTF .................................................................................... 125 [K] KIEN .................................................................................... 128 KUPIC ................................................................................. 115 [L] LINCR ................................................................................. 325 LINST .................................................................................. 326 [O] OCD ...................................................................................... 83 OFS ....................................................................... 27, 137, 356 [P] P1DRR .................................................................................. 64 PDi (i = 0, 1, and 3 to 5) ........................................................ 60 Pi (i = 0, 1, and 3 to 5) ........................................................... 61 PINSR1 ......................................................................... 62, 247 PINSR2 ................................................................................. 62 PINSR3 ................................................................................. 62 PM0 ....................................................................................... 77 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 452 of 453 PM1 ....................................................................................... 77 PMR ............................................................... 63, 247, 269, 299 PRCR .................................................................................. 109 PUR0 ..................................................................................... 64 PUR1 ..................................................................................... 64 [R] RMAD0 ................................................................................ 130 RMAD1 ................................................................................ 130 [S] S0RIC .................................................................................. 115 S0TIC .................................................................................. 115 S1RIC .................................................................................. 115 S1TIC ................................................................................... 115 SAR ..................................................................................... 298 SSCRH ................................................................................ 262 SSCRL ................................................................................. 263 SSER ................................................................................... 265 SSMR .................................................................................. 264 SSMR2 ................................................................................ 267 SSRDR ................................................................................ 268 SSSR ................................................................................... 266 SSTDR ................................................................................ 268 SSUIC .................................................................................. 116 [T] TRA ..................................................................................... 145 TRACR ................................................................................ 144 TRAIC .................................................................................. 115 TRAIOC ....................................... 144, 146, 149, 151, 153, 156 TRAMR ................................................................................ 145 TRAPRE .............................................................................. 145 TRBCR ................................................................................ 160 TRBIC .................................................................................. 115 TRBIOC ............................................... 161, 163, 167, 170, 175 TRBMR ................................................................................ 161 TRBOCR ............................................................................. 160 TRBPR ................................................................................ 162 TRBPRE .............................................................................. 162 TRBSC ................................................................................ 162 TRC ..................................................................................... 188 TRCCR1 ...................................................... 185, 208, 212, 217 TRCCR2 .............................................................................. 189 TRCDF ................................................................................ 190 TRCGRA ............................................................................. 188 TRCGRB ............................................................................. 188 TRCGRC ............................................................................. 188 TRCGRD ............................................................................. 188 TRCIC .................................................................................. 116 TRCIER ............................................................................... 186 TRCIOR0 ............................................................. 192, 201, 206 TRCIOR1 ............................................................. 192, 202, 207 TRCMR ................................................................................ 184 TRCOER ............................................................................. 191 TRCSR ................................................................................ 187 TRECR1 ...................................................................... 228, 235 TRECR2 ...................................................................... 229, 235 TRECSR ...................................................................... 230, 236 TREHR ................................................................................ 227 TREIC .................................................................................. 115 TREMIN ....................................................................... 226, 234 TRESEC ...................................................................... 226, 234 TREWK ................................................................................ 227 R8C/26 Group, R8C/27 Group [U] U0BRG ................................................................................ 244 U0C0 ................................................................................... 245 U0C1 ................................................................................... 246 U0MR .................................................................................. 244 U0RB ................................................................................... 243 U0TB ................................................................................... 243 U1BRG ................................................................................ 244 U1C0 ................................................................................... 245 U1C1 ................................................................................... 246 U1MR .................................................................................. 244 U1RB ................................................................................... 243 U1TB ................................................................................... 243 [V] VCA1 ..................................................................................... 39 VCA2 ................................................................... 39, 40, 86, 87 VW0C .................................................................................... 41 VW1C .............................................................................. 42, 43 VW2C .................................................................................... 44 [W] WDC .................................................................................... 137 WDTR ................................................................................. 138 WDTS .................................................................................. 138 Rev.2.10 Sep 26, 2008 REJ09B0278-0210 Page 453 of 453 Index REVISION HISTORY REVISION HISTORY R8C/26 Group, R8C/27 Group Hardware Manual R8C/26 Group, R8C/27 Group Hardware Manual Description Rev. Date 0.10 Jan 30, 2006 1.00 Nov 08, 2006 All pages "Preliminary" deleted Page - Summary First Edition issued 2 Table 1.1 revised 3 Table 1.2 revised 4 Figure 1.1 revised 5 Table 1.3 revised 6 Table 1.4 revised 7 Figure 1.4 revised 9 Table 1.6 revised 15 Table 4.1; * 001Ch: "00h" "00h, 10000000b" revised * 000Fh: "000XXXXXb" "00X11111b" revised * 0029h: "High-Speed On-Chip Oscillator Control Register 4, FRA4, When shipping" added * 002Bh: "High-Speed On-Chip Oscillator Control Register 6, FRA6, When shipping" added * 0032h: "00h, 01000000b" "00h, 00100000b" revised * 0038h: "00001000b, 01001001b" "0000X000b, 0100X001b" revised * NOTE3 and 4 revised; NOTE6 added 18 Table 4.4; * 00E0h, 00E1h, 00E5h, 00E8h, 00E9h: "XXh" "00h" revised * 00FDh: "XX00000000b" "00h" revised 23 Table 5.2 revised 24 Figure 5.4 NOTE2 revised 25 5.1.1 (2), 5.1.2 (4) revised 26 Figure 5.5, Figure 5.6 revised 27 Figure 5.7 revised 28 5.3 revised 33 Figure 6.5; VCA2 register NOTE6 revised 35 Figure 6.7 revised 46 Figure 7.2 revised 52 Figure 7.9 PINSR2 register revised 53 Figure 7.10 revised 58 Table 7.17 revised 60 Table 7.25 revised 64 Table 7.35, Table 7.36 revised 65 Table 7.37, Table 7.39 revised 69 Table 10.1 NOTE5 revised 70 Figure 10.1 revised 71 Figure 10.2 revised C-1 REVISION HISTORY Rev. Date 1.00 Nov 08, 2006 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 73 Figure 10.4 revised 74 Figure 10.5; FRA0 register NOTE2 and FRA1 register NOTE1 revised 75 Figure 10.6; FRA2 register revised, registers FRA4 and FRA6 added 76 Figure 10.8 NOTE6 revised 77 Figure 10.9 NOTE1 revised 78 10.2.2 revised 80 10.4.3 revised, 10.4.8 added 81 Table 10.2 revised 83 10.5.2.2, 10.5.2.3 revised 84 10.5.2.4, Table 10.3 revised 85 Figure 10.11 added 86 10.5.2.5 added, Figure 10.12 revised 88 10.5.3.3 revised, Figure 10.13 added 91 10.6.1 revised 92 Figure 10.16 revised 93 Figure 10.17 revised 94 10.7.1 revised, 10.7.2 added, 10.7.4 fOCO40M deleted 95 Figure 11.1 revised 96 Figure 12.1 revised 103 Figure 12.5 NOTE3 revised 106 Table 12.5 revised 108 Figure 12.10 revised 111 Figure 12.13 revised 117 Table 12.8 revised 121 12.6.7 deleted 122 Figure 13.1 revised 123 Figure 13.2 revised 126 Table 13.3 NOTE2 revised 127 14 revised 129 14.1, Figure 14.1 revised 130 Figure 14.2 revised 131 Figure 14.3 revised 132 Table 14.2, Figure 14.4 revised 133 14.1.1.1, Figure 14.5 added 134 Table 14.3 revised 135 Figure 14.6 revised 136 Table 14.4 revised 137 Figure 14.7 revised 138 Table 14.5 revised C-2 REVISION HISTORY Rev. Date 1.00 Nov 08, 2006 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 139 Figure 14.8 revised 140 Figure 14.9 revised 141 Table 14.6 revised 142 Figure 14.10 revised 143 Figure 14.11 revised 145 14.2, Figure 14.12 revised 146 Figure 14.13 revised 147 Figure 14.14 revised 148 Figure 14.15 revised 149 Table 14.7, Figure 14.16 revised 150 14.2.1.1 added 151 Figure 14.17 added 152 Table 14.8 revised 153 Figure 14.18 revised 154 Figure 14.19 revised 155 Table 14.9 revised 156 Figure 14.20 revised 158 14.2.3.1 added 159 Table 14.10 revised 160 Figure 14.22 revised 161 Figure 14.23 revised 162 14.2.5 revised 178 Figure 14.38 revised 182 Figure 14.40 revised 190 Figure 14.47 revised 194 Figure 14.50 revised 198 Table 14.22 revised 199 Figure 14.54 revised 203 Table 14.24 revised 205 14.4 revised 206 Figure 14.59 revised 214 Figure 14.69 revised 226 Figure 15.4; U0MR to U1MR register revised 228 Figure 15.6 revised 229 Figure 15.7; PMR register revised 230 Table 15.1 NOTE2 revised 232 Figure 15.8 revised 235 Table 15.4 NOTE1 revised 236 "TXD0" "TXDi" revised C-3 REVISION HISTORY Rev. Date 1.00 Nov 08, 2006 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 237 Figure 15.11 revised 238 Figure 15.12 revised 242 Table 16.2 NOTE2 deleted 245 Figure 16.3 revised 246 Figure 16.4 revised 249 Figure 16.7 revised 250 Figure 16.8 SSTDR register NOTE1 deleted 251 Figure 16.9 revised 258 16.2.5.2 revised 259 Figure 16.14 NOTE2 deleted 262 16.2.5.4 revised 263 Figure 16.17 NOTE2 deleted 265 Figure 16.18 revised 266 16.2.6.2 revised 267 Figure 16.19 revised 271 16.2.8.1 revised 274 Figure 16.23 revised 275 Figure 16.24 NOTE1 revised 277 Figure 16.26 NOTE3 revised 282 Figure 16.31 revised 285 Figure 16.32 revised 287 Figure 16.33, Figure 16.34 revised 289 Figure 16.35 revised 290 Figure 16.36 revised 301 to 304 Figure 16.46 to Figure 16.49 figure title revised and Figure 16.47 revised 306 to 320 17 "Sync" "Synch" revised 308 Figure 17.2 revised 310 Figure 17.4 revised 311 Figure 17.5 revised 312 Figure 17.6 revised 313 17.4.2 (5), Figure 17.7 revised 314 Figure 17.8 revised 315 Figure 17.9 revised 316 Figure 17.10 revised 317 Figure 17.11 revised 318 17.4.4, Figure 17.12 added 319 17.5, Table 17.2 revised 321 Table 18.1 revised 322 Figure 18.1 revised C-4 REVISION HISTORY Rev. Date 1.00 Nov 08, 2006 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 324 Figure 18.3 revised 325 Table 18.2 revised 329 Figure 18.6 revised 331 18.3 revised 332 Figure 18.10 revised 333 18.6 revised 334 18.7 revised 335 Table 19.1 revised 339 Figure 19.4 NOTE2 revised 340 Table 19.3 revised 342 19.4.2.1 revised 346 Figure 19.7 revised 347 Figure 19.8 revised 350 19.4.3.1, 19.4.3.2 revised 351 19.4.3.4 revised, Figure 19.12 title revised 352 Figure 19.13 added 353 Figure 19.14 title revised 354 Figure 19.15 revised 357 Figure 19.16 revised 364 19.7.1.7 deleted 365 Table 20.2 revised 366 Figure 20.1 title revised 367 Table 20.4 revised 368 Table 20.5 revised 369 Figure 20.2 title revised and Table 20.7 NOTE4 added 370 Table 20.9, Figure 20.3 revised and Table 20.10 deleted 371 Table 20.10, Table 20.11 revised 377 Table 20.15 revised 378 Table 20.16 revised 379 Table 20.17 revised 382 Table 20.22 revised 383 Table 20.23 revised 387 Table 20.29 revised 390 21.1.1 revised, 21.1.2 added, 21.1.4 fOCO40M deleted 393 21.2.7 deleted 395 21.3.2 revised 401 21.5.1.1 revised 402 21.6 revised 403 21.7 revised C-5 REVISION HISTORY Rev. Date 1.00 Nov 08, 2006 1.10 Jan 17, 2007 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 406 21.8.1.7 deleted 408 22 (2) revised, (5) deleted 409 Appendix 1; "Diagrams showing the latest...website." added - "J, K version" added 1 1 "J and K versions are under development...notice." added 1.1 revised 2 Table 1.1 revised 3 Table 1.2 revised 4 Figure 1.1 NOTE3 added 5 Table 1.3 and Figure 1.2 revised 6 Table 1.4 and Figure 1.3 revised 7 Figure 1.4 NOTE3 added 8 Table 1.5 revised 9 Table 1.6 NOTE2 added 13 Figure 3.1 revised 14 Figure 3.2 revised 15 Table 4.1; "0000h to 003Fh" "0000h to 002Fh" revised * NOTE3 added 16 Table 4.2; "0040h to 007Fh" "0030h to 007Fh" revised * 0032h, 0036h: value after reset is revised * 0038h: NOTE revised * NOTES 2, 5, 6 revised and NOTES 7, 8 added 18 Table 4.4 NOTE2 added 19 Table 4.5 NOTE2 added 22 5 "(for N, D version only)" added Table 5.1 NOTE1 added Figure 5.1 figure title "(N, D Version)" added 23 Figure 5.2 added 25 Figure 5.5 revised 27 Figures 5.6 and 5.7 revised 28 5.2 revised Figure 5.8 revised 29 Figure 5.9 added 30 5.3, 5.4 titles "(N, D Version)" added 5.5 added 32 6 "...voltage monitor 0 reset (for N, D version only), voltage monitor 1 interrupt (for N, D version only)..." revised Table 6.1 table title "(N, D Version)" added 33 Table 6.2 added Figure 6.1 figure title "(N, D Version)" added C-6 REVISION HISTORY Rev. Date 1.10 Jan 17, 2007 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 34 Figure 6.2 added Figure 6.3 figure title "(For N, D Version Only)" added 35 Figure 6.4 figure title "(N, D Version)" added Figure 6.5 added 37 Figure 6.7; VCA2 register figure title and NOTE6 revised 38 Figure 6.8 added 39 Figure 6.9 figure title "(For N, D Version Only)" added 40 Figure 6.10 figure title "(N, D Version)" added 41 Figure 6.11 added 42 Figure 6.12 NOTE8 revised 44 6.2 Title "(For N, D Version Only)" added 45 6.3 Title "(N, D Version)" added 46 Figure 6.14 figure title "(N, D Version)" added 47 6.4 added 50 7 NOTE1 added and Table 7.1 NOTE3 revised 56 Figure 7.5 revised 62 Figure 7.13 "(For N, D Version Only)" added 63 Table 7.4 NOTE1 revised 73 Table 7.35 NOTE1 added and Table 7.36 NOTE2 added 78 10 revised and Table 10.1 "(For N, D Version Only)" added 79 Figure 10.1 NOTE1 added 80 Figure 10.2 NOTE12 added 81 Figure 10.3 NOTE10 added 83 Figure 10.5; FRA0 register NOTE2 revised 84 Figure 10.6; FRA2 register NOTE2 added, registers FRA4 and FRA6 "For N, D Version Only" added 85 Figure 10.7 "(For N, D Version Only)" added, figure 10.8 figure title and NOTE6 revised 86 Figure 10.9 added 87 Figure 10.10 added 88 Figure 10.11 NOTE1 revised 89 10.2.2 revised 90 10.3 Title "(For N, D Version Only)" added 91 10.4.1, 10.4.2, and 10.4.8 revised 92 Table 10.2 NOTE1 added 93 10.5.1.2 and 10.5.1.4 revised 95 Table 10.3 revised 96 Figure 10.13 revised 97 10.5.2.5 and Figure 10.14 revised C-7 REVISION HISTORY Rev. Date 1.10 Jan 17, 2007 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 98 Table 10.4 NOTE1 added 99 Figure 10.15 revised 101 Figure 10.17 "(For N, D Version Only)" added 103 Table 10.6 NOTE1 added 104 Figure 10.19 "(N, D Version)" added 105 Figure 10.20 added 106 10.7.1, 10.7.2 revised 110 12.1.3.1 revised 12.1.3.3 "(For N, D Version Only)" added 111 Table 12.1 NOTE2 added 118 Table 12.5 NOTE1 added 120 Figure 12.10 NOTE1 added 121 Figure 12.11 NOTE2 added 127 Table 12.6 revised 131 12.6.4 deleted 135 Figure 13.2; OFS register revised 140 Table 14.1 NOTES 1, 2 added 141 Figure 14.1 NOTE1 added 143 Figure 14.3 NOTE2 added 146 Table 14.3 NOTE2 added 150 Table 14.5 NOTE1 added 153 Table 14.6 NOTE2 added 167 Table 14.9 NOTE2 added 171 Table 14.10 NOTE2 added 213 Figure 14.56 revised 217 14.4 "(For J, K version...)" added 218 14.4.1 Title "(For N, D Version Only)" added 226 Figure 14.69 NOTE1 added 227 Table 14.27 NOTE1 added 230 Figure 14.74 NOTE2 added 252 15.3 revised 287 Figure 16.24 NOTE7 added 317 16.3.8.2, 16.3.8.3 added 333 Table 18.1 revised 335 Figure 18.2 NOTE4 revised 338 Figure 18.4 NOTE4 revised 341 Figure 18.6 NOTE4 revised 346 18.7 revised 351 Figure 19.4 revised C-8 REVISION HISTORY Rev. Date 1.10 Jan 17, 2007 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 353 19.4.1, 19.4.2 revised 361 Figure 19.11 revised 364 Figure 19.13 revised 368 Table 19.6 revised 383 Table 20.10 revised 402 to 421 20.2 J, K Version added 1.20 May 18, 2007 422 21.1.1, 21.1.2 revised 423 21.2.4 deleted 432 21.4 revised 434 21.5.2.2, 21.5.2.3 added 436 21.7 revised 443 Appendix Figure 2.1 NOTE2 deleted - "RENESAS TECHNICAL UPDATE" reflected: TN-16C-A164A/E, TN-16C-A167A/E 2 Table 1.1 revised 3 Table 1.2 revised 5 Table 1.3 revised 6 Figure 1.2 revised 7 Table 1.4 revised 8 Figure 1.3 revised 9 Figure 1.4 NOTE4 added 15 Figure 3.1 part number revised 16 Figure 3.2 part number revised 26 Figure 5.4 revised 54 Figure 7.1 revised 55 Figure 7.2 revised 68 Table 7.18 revised 70 Table 7.24 revised 82 Figure 10.2 NOTE3 revised 85 Figure 10.5 FRA1 register revised 98 10.5.2.4 revised 104 10.6.1 revised 124 12.2.1 revised 134 Figure 12.20 NOTE2 revised 141 14 "two 16-bit timers" "a 16-bit timer" revised 147 Figure 14.5 revised 158 14.1.6 revised 159 Figure 14.12 revised 165 Figure 14.17 revised C-9 REVISION HISTORY Rev. Date 1.20 May 18, 2007 R8C/26 Group, R8C/27 Group Hardware Manual Description Page 173 Summary Table 14.10 revised 176 to 179 14.2.5.1 to 14.2.5.4 added 203 Table 14.18 revised 229 Figure 14.69 revised 243 Figure 15.4 UiMR register NOTE2 deleted 253 Table 15.5 NOTE2 added 261 Figure 16.2 NOTE4 deleted 262 Figure 16.3 NOTE4 deleted 263 Figure 16.4 NOTE2 deleted 264 Figure 16.5 NOTE1 deleted 265 Figure 16.6 NOTE2 revised and NOTE7 deleted 266 Figure 16.7 NOTE5 revised 267 Figure 16.8 Registers SSTDR and SSRDR; NOTE1 deleted 288 16.2.8.1 deleted 292 Figure 16.24 NOTE6 deleted 293 Figure 16.25 NOTE5 deleted 294 Figure 16.26 NOTE7 deleted 295 Figure 16.27 NOTE3 deleted 296 Figure 16.28 NOTE7 deleted 297 Figure 16.29 Registers SAR, ICDRT, and ICDRR; NOTE1 deleted 321 16.3.8.1 deleted 350 18.7 revised 351 Table 19.2 revised 356 Table 19.3 revised 358 19.4.2.4 revised 359 19.4.2.15 revised 360 Figure 19.5 NOTES 3 and 5 revised 362 Figure 19.7 NOTE5 revised 364 Figure 19.9 revised 365 Figure 19.11 revised 367 19.4.3.4 revised 368 Figure 19.13 revised 370 Figure 19.15 revised 387 Table 20.10 revised 410 Table 20.39 NOTE4 added 412 Table 20.42 revised 428 Figure 21.1 NOTE2 revised 430 21.3.1 revised 431 to 434 21.3.2.1 to 21.3.2.4 added C - 10 REVISION HISTORY Rev. Date 1.20 May 18, 2007 1.30 2.00 Jun 01, 2007 Mar 01, 2008 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 440 21.5.1.2 and 21.5.2.1 deleted 442 21.7 revised 450 Appendix Figure 3.1 NOTE1 revised 162 Figure 14.15 TRBPR register NOTE2 revised 176 14.2.5 NOTE revised 328 Figure 17.6 revised 329 Figure 17.7 "B0CLR bit" revised 331 Figure 17.9 revised 433 Figure 21.3 revised 1, 407 1.1, 20.2 "J and K versions are ..." deleted 5, 7 Table 1.3, Table 1.4 revised 11 Table 1.6 NOTE3 added 15, 16 Figure 3.1, Figure 3.2; "Expanded area" deleted 17 Table 4.1 "002Ch" added 18 Table 4.2 "0036h"; J, K version "0100X000b" "0100X001b" 27, 137, Figure 5.5, Figure 13.2, Figure 19.4; "OFS Register" revised 356 67 Table 7.14 revised 70 Table 7.26 revised 71 Table 7.28 revised 80 Figure 10.1 revised 81 Figure 10.2 "Set to 0." "Do not set to 1." 85 Figure 10.6 "FRA7 Register" added 90 10.2.2 revised 93 10.4.9 added 95 10.5.1.4 "... clock ..." "... on-chip oscillator ..." 114 Table 12.2 "Reference" revised 124 12.2.1 "The INT0 pin is shared ..." deleted Table 12.6 added 142 Table 14.1 "* fC32" deleted 143 Figure 14.1 "TSTART" "TCSTF" 159 14.2 "The reload register and ..." deleted Figure 14.2 "TSTRAT" "TSTART" 162 Figure 14.15 revised 166 Table 14.8 "(P1_3)" "* TRBO pin select function ..." added 169, 174 Table 14.9, Table 14.10 "* TRBO pin select function ..." added 170 Figure 14.20 "... When write, ..." "... If necessary, ..." 189 Figure 14.33 revised 192 Figure 14.36 TRCIOR0: b3 revised, NOTE4 added C - 11 REVISION HISTORY Rev. Date 2.00 Mar 01, 2008 R8C/26 Group, R8C/27 Group Hardware Manual Description Page Summary 199 14.3.4 "The TRCGRA register can also select fOCO128 signal ..." added Table 14.16 revised 200 Figure 14.42 revised 201 Figure 14.43 b3 revised, NOTE3 added 206 Figure 14.47 b3 revised 209 Figure 14.50 "* The CCLR bit ... 0 ..." "* The CCLR bit ... 1 ..." 210 Table 14.20 revised 216 Table 14.22 revised 239 Figure 14.78 revised 246 Figure 15.6 "(b7-b4)" "(b7-b6)" 257 Table 15.7 revised 263 Figure 16.3 "Cannot write to this." "The SOLP bit ..." 266 Figure 16.6 NOTE7 added 283 Figure 16.18 revised 297 Figure 16.28 NOTE7 added 323 Figure 17.1 revised 328 Figure 17.5 revised 329 Figure 17.6 revised 332 Figure 17.9 revised 335 Figure 17.12 revised 349 Figure 18.10 revised 373 Table 19.6 "FRM0 Register ..." "FMR0 Register ..." 382, 407 Table 20.2, Table 20.35; NOTE2 revised 2.10 Sep 26, 2008 388 Table 20.10 revised, NOTE4 added 438 Figure 21.4 revised 450 Appendix Figure 2.2 revised - "RENESAS TECHNICAL UP DATE" reflected: TN-16C-A172A/E 31 Figure 5.9 revised 60 Figure 7.8 NOTE3 revised 61 Figure 7.9 NOTE2 revised 143 Figure 14.1 revised 151 Figure 14.7 TOENA bit revised 280 16.2.5.4 "When exiting transmit/receive .... set the RE bit to 1." added 352 Table 19.1 NOTE1 revised 384, 409 Table 20.4, Table 20.37 NOTE2, NOTE4 revised 385, 410 Table 20.5, Table 20.38 NOTE2, NOTE5 revised 411 Table 20.39 Parameter: Voltage monitor 1 reset generation time added NOTE5 added Table 20.40 revised C - 12 REVISION HISTORY Rev. Date 2.10 Sep 26, 2008 R8C/26 Group, R8C/27 Group Hardware Manual Description Page 412 Summary Table 20.41 revised Figure 20.22 revised C - 13 R8C/26 Group, R8C/27 Group Hardware Manual Publication Date: Published by: Rev.0.10 Rev.2.10 Jan 30, 2006 Sep 26, 2008 Sales Strategic Planning Div. Renesas Technology Corp. (c) 2008. Renesas Technology Corp., All rights reserved. Printed in Japan R8C/26 Group, R8C/27 Group Hardware Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ09B0278-0210