Application Specification Universal 114-1010 MATE-N-LOK* Connectors 12 OCT 07 Rev P All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 . Figures and illustrations are for identification only and are not drawn to scale. _ NOTE i 1. INTRODUCTION This specification covers the requirements for application of Universal MATE-N-LOK Housings, Contacts, and Printed Circuit (PC) Board Headers. The housings are available in 1- through 15-circuit versions and are intended for use in wire-to-wire (panel mounted or free hanging) or wire-to-board applications. The vertical pin and socket headers are available in 2- through 15-circuit versions and are intended for board-to- wire applications. The right-angle pin and socket headers are available in 2- through 8-circuit in-line versions and are intended for board-to-wire applications. When corresponding with Tyco Electronics Personnel, use the terminology provided in this specification to facilitate your inquiries for information. Basic terms and features of this product are provided in Figure 1. Plug Housing Identification Rib Identification Rib Cap Housing Panel Mount Strain Panel Mount Relief Polarizing Rib Tabs Back of Slot Housing Polarizing (Wire End) Cavities Panel Back of Housing Locking (Wire End) Tab Locking Latch Mount Latch Socket Contact Twist and Lock Wire Barrel Cap Housing Insulation Panel Mount Barrel Helix Locking Back of Housing Tab (Wire End) Locking Lance Identification Polarizing Rib Cavity Pin Contact Cavity High Retention Cavity Identification Pin Contact Identification Locking Tab Front of Header (Mating End) Mounting Ears Solder Tail (Typ) Right-Angle PC Board Header Vertical PC Board Header Locking Tab (Pin or Socket) E 2007 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved Figure 1 (Pin or Socket) TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 19 LOC B Universal MATE-N-LOK Connectors 114-1010 2. REFERENCE MATERIAL 2.1. Revision Summary This paragraph is reserved for a revision summary covering the most recent additions and changes made to this specification which include the following: S S S S Updated document to corporate requirements Added new high retention pin and related information to Figures 1, 3, and 19 Deleted instruction sheet 408-4371 and added 408-10049 in Paragraph 2.5 Added artwork for extraction tool 1804030-1 in Figures 6 and 18 and text in Paragraph 3.4.B 2.2. Customer Assistance Reference Base Part Number 480702 and Product Code 1318 are representative numbers of the Universal MATE-N-LOK product line. Use of these numbers will identify the product line and expedite your inquiries through a Tyco Electronics service network established to help you obtain product and tooling information. Such information can be obtained through a local Tyco Electronics Representative or, after purchase, by calling the Product Information Center number at the bottom of page 1. 2.3. Drawings Customer Drawings for specific products are available from the responsible Tyco Electronics Engineering Department via the service network. The information contained in the Customer Drawing takes priority if there is a conflict with this specification or any other technical documentation supplied by Tyco Electronics. 2.4. Specifications Product Specifications 108-1031 (for connectors), and 108-1053 (for headers), provides product performance requirements and test result information. 2.5. Instructional Material The following list includes available instruction sheets (408-series) that provide assembly procedures for product, and operation, maintenance and repair of tooling; and customer manuals (409-series) that provide setup, operation, and maintenance of machines. Document Number 408-2095 408-3295 408-3320 408-7300 408-7424 408-7714 408-7984 408-8040 408-8053 408-8059 408-8547 408-9433 408-9591 408-9816 408-10049 409-5842 409-5852 409-5870 409-5878 409-10027 409-10029 409-10047 2 of 19 Document Title Hand Crimping Tool 69710-1 Preparing Reel of Contacts for Application Tooling Universal MATE-N-LOK Strain Relief Assembly and Keying Plug MATE-N-LOK Contact and Housing Selection Charts Checking Terminal Crimp Height or Gaging Die Closure Universal MATE-N-LOK Connectors Insertion Tool 455830-1 Heavy Duty Miniature Quick-Change Applicators (Side-Feed Type) Conversion Guide for Miniature Quick-Change Applicators General Preventive Maintenance for Applicators CERTI-CRIMP* II Straight Action Hand Tools Crimping Die Assemblies 58380-1 and 58380-2 Hand Crimping Tool 58439-1 Handling of Reeled Products Extraction Tool 1804030-1 AMP-O-LECTRIC* Model "G" Terminating Machines 354500-[ ] AMPOMATOR* CLS III-G Lead-Making Machine 122500-[ ] Crimp Quality Monitors (CQM) for AMPOMATOR CLS IV Lead-Making Machines AMPOMATOR CLS IV+ Lead-Making Machine 356500-[ ] Stripping Modules 1490500 and 1490502 Stripping Modules 1490501 and 1490503 AMP-3K Terminating Machines 1725950 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 2.6. Manuals Manual 402-40 is available upon request and can be used as a guide in soldering. This manual provides information on various flux types and characteristics along with the commercial designation and flux removal procedures. A checklist is attached to the manual as a guide for information on soldering problems. 3. REQUIREMENTS 3.1. Storage A. Ultraviolet Light Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in the housing material. B. Reel Storage When using reeled contacts, store coil wound reels horizontally and traverse wound reels vertically. C. Shelf Life Each connector is packaged and shipped in an individual antistatic tube container or tape and reel. To prevent damage to the housings and contact solder tines, the connectors should remain in the container until ready for installation. Also, to prevent possible storage contamination and ensure maximum solderability, the connectors should be used on a first in, first out basis. D. Chemical Exposure Do not store contacts near any of the following chemicals as they may cause stress corrosion. Alkalies Amines NOTE Ammonia Carbonates Citrates Nitrites Phosphates Citrates Sulfides Nitrites Sulfur Compounds Tartrates Where the above environmental conditions exist, phosphor-bronze contacts are recommended instead of brass if available. i 3.2. Wire A. Wire Selection The contacts will accept stranded wires ranging in size from 10 to 30 AWG. Wire insulation diameter shall have minimum and maximum dimensions according to the wire sizes indicated in Figure 2. Reasonable care shall be taken during the stripping operation to ensure the conductor is not nicked, scraped, or cut. NOTE Contacts accept stranded wire only. Not intended for solid wire. i B. Wire Preparation The wire strip length shall be according to the wire sizes as indicated in Figure 2. Insulation Stranded Wire Conductor Strip Length Note: Not to Scale Rev P Insulation Diameter Figure 2 (cont'd) Tyco Electronics Corporation 3 of 19 Universal MATE-N-LOK Connectors 114-1010 AUTOMATIC MACHINE WIRE CRIMP DIMENSIONS WIRE WIRE BARREL INSULATION SIZE (AWG) 30 28 26 INSULATION DIAMETER RANGE 00.81 81 to t 1.45 1 45 [.032 to .057] STRIP CRIMP LENGTH HEIGHT " 0.38 [.015] 0.71 [.028] 44.06 06 [.160] 0.71 [.028] 0.76 [.030] 24 22 20 +0.05 [.002] 1.02 to 2.54 [.040 to .100] 1.02 [.040] 4.37 [.172] 1.09 [.043] 1.22 [.048] 20 1.19 [.047] 16 1.52 to 3.30 [.060 to .130] 1.32 [.052] 4.37 [.172] 1.50 [.059] 14 1.75 [.069] 20 1.19 [.047] 18 1.32 [.052] 16 14 3.30 to 5.08 [[.130 130 to .200] 200] 1.50 [.059] 4.37 [[.172] 172] 1.75 [.069] 2 @ 18 1.60 [.063] 18 1.50 [.059] 16 3.30 to 5.08 [ 30 to .200] [.130 00] 4.37 [ [.172] ] 1.68 [.066] 14 12 10 BARREL WIDTH CRIMP WIDTH 1 40 1.40 [.055] 2 29 2.29 [.090] 1.78 [.070] 2.54} [.100] 2.29 [.090] 3.30 [.130] 0.96 [.038] 18 18 CRIMP 2.29 [[.090] 090] 5.08 [.200] 4.83 [.190] 2.29 [ 090] [.090] 5.08 [ 00] [.200] 3.56 [.140] -- 1.93 [.076] 5.08 [[.200]] Max. 1.96 [.077] 6.76 [.266] 2.41 [.095] HAND TOOL WIRE CRIMP DIMENSIONS WIRE WIRE BARREL INSULATION SIZE (AWG) 30 28 26 INSULATION STRIP CRIMP DIAMETER LENGTH HEIGHT RANGE +0.38 [.015] +0.05 [.002] 00.81 81 to t 1.45 1 45 [.032 to .057] 44.06 06 [.160] 24 22 20 18 0.71 [.028] 0.71 [.028] 0.71 [.028] CRIMP WIDTH BARREL CRIMP WIDTH 1 40 1.40 [.055] 2 29 2.29 [.090] 1.78 [.070] 2.54 [.100] 1.02 [.040] 1.02 to 2.54 [.040 to .100] 4.37 [.172] 1.02 [.040] 1.17 [.046] 1.17 [.046] }For part numbers 770210-1 and 770211-1, insulation barrel crimp width should be 3.30 [.130]. Figure 2 (cont'd) 4 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 HAND TOOL WIRE CRIMP DIMENSIONS WIRE WIRE BARREL INSULATION SIZE (AWG) INSULATION STRIP CRIMP DIAMETER LENGTH HEIGHT RANGE +0.38 [.015] +0.05 [.002] 20 BARREL CRIMP WIDTH CRIMP WIDTH 1.27 [.050] 18 1.52 to 3.30 [.060 to .130] 16 4.37 [.172] 1.27 [.050] 1.60 [.063] 14 1.60 [.063] 20 1.24 [.049] 18 3.30 to 5.08 [.130 to .200] 16 4.37 [.172] 14 1.24 [.049] 1.60 [.063] 2.29 [.090] 3.30 [.130] 2.29 [.090] 5.08 [.200] 3.56 [.140] -- 1.60 [.063] 12 5.08 [[.200]] Max. 10 6.76 [.266] 2.11 [.083] 2.44 [.096] Figure 2 (end) 3.3. Crimped Contact Requirements The contact shall be located in desired tooling and crimped according to the instructions packaged with that tooling. See Section 5, TOOLING, of this document for details on tooling options and instructional materials. CAUTION Wire insulation shall NOT be cut or broken during the crimping operation, nor shall the insulation be crimped into the contact wire barrel. Reasonable care should be taken by tooling operators to provide undamaged wire terminations. ! NOTE Wire stripping tool jaws may leave corrugated indentations on the surface of the wire insulation. This is especially severe with cross-linked polyethylene (high temperature) insulation. If these indentations occur at the location of the i wire seal, leakage may result. Insulation surface within 8.89 mm from the tip of the contact must be smooth and free of indentations. See Figure 3. A. Wire Barrel Crimp The crimp applied to the wire portion of the contact is the most compressed area and is most critical in ensuring optimum electrical and mechanical performance of the crimped contact. The contact wire barrel crimp height must be within the dimension provided in Figure 2. B. Effective Crimp Length For optimum crimp effectiveness, the crimp must be within the area shown in Figure 3 and must meet the crimp dimensions provided in Figure 2. Effective crimp length shall be defined as that portion of the wire barrel, excluding bellmouth(s), fully formed by the crimping tool. Instructions for adjusting, repairing, and inspecting tools are packaged with the tools. See Section 5, TOOLING. C. Bellmouths Front and rear bellmouths shall be evident and conform to the dimensions given in Figure 3. D. Cutoff Tabs The cutoff tab shall be cut to the dimensions shown in Figure 3. E. Burrs The cutoff burr shall not exceed the dimensions shown in Figure 3. F. Wire Barrel Flash The wire barrel flash shall not exceed the dimensions shown in Figure 3, Section X-X. Rev P Tyco Electronics Corporation 5 of 19 Universal MATE-N-LOK Connectors 114-1010 High Retention Pin Contact Locking Lance Shall Not be Deformed The Wire Barrel Seam Shall be Closed Adequately to Confine All Strands of the Wire. There Shall be No Loose Wire Strands or Wire Strands Embedded in the Outside of the Wire Barrel. Wire Strands and Insulation Both Visible. Note: Large Diameter Insulation May Not be Visible When Crimping with Hand Tools. Flush to 1.02 [.040] Max. Socket Contact Front Bellmouth 0.25 +0.00/-0.25 [.010 +.000/-.010] Locking Lance Shall Not be Deformed Rear Bellmouth 0.13 [.005] to 0.76 [.030] X X 0.25 [.010] Max Wire Barrel Flash Wire Barrel Crimp Width Wire Barrel Crimp Height Cutoff Tab 0.25 [.010] Max. Section X-X No Burrs Figure 3 6 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 G. Insulation Barrel Crimp The insulation barrel shall grip the insulation firmly without cutting into it. Care must be taken to prevent cutting, nicking, or scraping of the insulation. Insulation crimp shall comply to width and height provided in Figure 2. H. Wire Location The wire conductor and insulation must be visible in the transition area between the wire and insulation barrels as shown in Figure 3. I. Conductor Extension The conductor may extend beyond the wire barrel to the maximum shown in Figure 3. J. Wire Barrel Seam The wire barrel seam must be closed with no evidence of loose wire strands visible in the seam as shown in Figure 3. K. Twist and Roll There shall be no twist, roll, deformation or other damage to the mating portion of the crimped contact that will impair usage of the contact. See Figure 4. No Twist Permitted Wire Barrel Figure 4 L. Straightness/Alignment The force applied during crimping may cause some bending between the crimped wire barrel and the mating portion of the contact. The axial concentricity of the crimped wire barrel shall fall into an area defined by a 4.19 mm [.165 in.] diameter circle whose center is the centerline of the contact. The axial concentricity of the crimped insulation barrel shall fall into an area defined by a 5.59 mm [.220 in.] diameter circle whose center is the centerline of the contact. Such deformation is acceptable within the limits provided in Figure 5. NOTE Periodic inspections must be made to ensure crimped contact formation is consistent as shown. i Centerline of Circle and Contact Wire Barrel Insulation Barrel Figure 5 Rev P Tyco Electronics Corporation 7 of 19 Universal MATE-N-LOK Connectors 114-1010 3.4. Housings A connector assembly consists of a plug and a cap connector. A connector consists of a housing (plug or cap) with a specified number of crimp contacts (pin and/or socket). Mating connectors may be a plug and a cap, or a plug and a pc board header, so long as both have an identical number of circuits with a pin contact mating with a socket contact. Both the plug and cap housings have individually numbered cavity identification on the BACK (wire end), plus an identification rib on the SIDE indicating the No. 1 cavity. The housings feature polarizing cavities on the mating end and are intermateable with Universal MATE-N-LOK II connectors. The plug housing has two locking latches and the cap housing has two locking tabs. The housings are designed for free hanging or panel mounting applications (refer to Paragraph 3.9, Panel Cutout). A. Assembly Crimped pin and socket contacts shall be manually inserted in either the plug or cap housing, or they may be intermixed in each housing to provide multiple keying combinations. See Figure 6. NOTE Insertion Tool 455830-1 (408-7984) is available for inserting contacts crimped to small wire sizes. i B. Disassembly Extraction Tool 1804030-1 (408-10049) is designed for removing pin and socket contacts from plug and cap housings. See Figure 6. Front of Housing (Mating End) Back of Housing Extraction Tool (Wire Entry End) 1804030-1 Interlock Pin Contact Contact (Ref) Lever Cavity Contact Extraction Tip Cavity Wire Insulation Figure 6 C. Strain Relief and Wire Dress If necessary, wires can be bundled together and supported with cable ties or similar device. Wires must not be stretched or confined in any way. Therefore, the wires must remain perpendicular to the connector and avoid an excessively sharp bend radius. The minimum distance for the cable tie, measured from the housing at the wire end of the connector to the cable tie is shown in Figure 7. 3.5. Headers The pc board headers are supplied preloaded with solder tail pin contacts or solder tail socket contacts. Vertical pin and socket headers are available in 2 through 15 circuits. Right-angle pin and socket headers are available in 2 through 8 circuits. All headers feature individually numbered cavity identification on the FRONT (mating end). The headers also feature polarizing cavities and locking tabs. The headers are designed to be mounted on a pc board (refer to Paragraph 3.10.C, Printed Circuit Board Layout). 8 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 76.2 [3.0] Min Distance Housing Cable Tie (Ref) or Any Wire Dress Figure 7 3.6. Strain Relief Assembly The strain relief assembly is designed to relieve the stress of the wires on the contacts. There are two strain relief versions (open and enclosed). The open version is available for 2 through 15 circuit plug housings. The enclosed version is available for 2 through 15 circuit plug or cap housings. The enclosed version features an attached insert for smaller wire bundles. Adapters are required when installing an enclosed strain relief assembly onto a cap housing. Two identical strain reliefs are inserted into slots in the back of the connector (or adapter) and are secured together with two No. 6 pan head self-tapping screws. See Figure 8. Insert Cap Connector Open Version Enclosed Version Adapter Enclosed Strain Relief Figure 8 Rev P Tyco Electronics Corporation 9 of 19 Universal MATE-N-LOK Connectors 114-1010 3.7. Keying Plugs Keying plugs provide additional polarization for the connectors. The keying plug may be inserted into the front of the plug or the cap connector. See Figure 9. Empty Contact Cavity Split Tapered End Front of Connector (Mating End) Figure 9 3.8. Test Connectors Plug and cap test connectors mate with respective assembled plug and cap connectors and headers to test the electrical circuit. The test connectors are preloaded with spring loaded contacts that will mate with pin or socket contacts in the connector. The 2.13 mm [.084 in.] dia pin that extends out the BACK of the housing will accept Universal MATE-N-LOK socket contacts. See Figure 10. Plug Cap 2.13 [.084] Dia Pin (Typ) Figure 10 NOTE Test connectors have a 5 ampere maximum current rating per circuit. i 3.9. Panel Cutout Cap connector panel mounting cutouts shall be as indicated in Figure 11. (No mounting hardware is required.) The cap housing features flexible mounting latches for insertion into the panel. Push the cap connector through the panel - in the same direction as the cutout was made - until it snaps in place. 10 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 4.44+0.25 114-1010 NUMBER OF CIRCUIT POSITIONS Cap Connector Panel Cutout [.175+.010] A C H 4.44+0.25 E 4 D E +0.13 [.005] 20.70 2.41 8.64 13.46 [.815] [.095] [.340] [.530] 6.98 12.19 26.16 [.275] [.480] [1.030] 27.05 6.35 [1.065] [.250] [.565] 20.70 9 [.815] 12 15 27.05 8.89 [1.065] [.350] 33.40 8.89 [1.315] [.350] H Optional panel cutout dimensions for cap and panel polarization. H+0.13 [.110H+.005] 2.79 Twist and Lock Cap Panel Cutout D +0.25 [.010] 14.35 6 Direction of Cutout Punch and Cap Entry C +0.25 [.010] [.565] 3 [.175+.010] BH +0.25 [.010] 14.35 2 B DIMENSIONS A +0.13 [.005] H+0.13 [.110H+.005] Panel Thickness - .762 [.030] to 2.286 [.090] 2.79 DIMENSION 2.92 [.115] A" A B" C" E D" E" POSITION SIZE 6 and 9 12 34.67 40.13 [1.365] [1.580] 4.70 6.15 [.185] [.242] 29.08 34.54 [1.145] [1.360] 7.37 8.08 [.290] [.318] 0.25 1.98 [.010] [.078] B C D Figure 11 Rev P Tyco Electronics Corporation 11 of 19 Universal MATE-N-LOK Connectors 114-1010 The Twist and Lock cap housing features a round helix for insertion into the panel. Refer to the panel cutout dimensions as shown in Figure 11. The Twist and Lock panel cutout is polarized to ensure proper installation of the connector. Align the pin 1 indicator rib with the short side polarization opening of the panel and push the cap connector through the panel. Twist the connector clockwise until firmly seated. The panel thickness may vary between 0.76 and 2.29 mm [.030 and .090 in.]. In order to prevent foam leakage, the maximum amount of "gap" between the connector flange and the panel is 0.25 mm [.010 in.]. Refer to Figure 12. Short Side Polarization Maximum Gap" = Customer Panel Feature 0.25 mm [.010 in.] Pin 1 Indicator Figure 12 3.10. PC Board A. Material and Thickness 1. Board material will be glass epoxy (FR-4, G-10). 2. The connector headers can be installed on pc boards up to 1.57 mm [.062 in.] thick for standard tails, and 3.18 mm [.125 in.] for long tails. Board thickness may vary depending upon the application. Contact the Product Information Center or the Tooling Assistance Center number listed at the bottom of page 1 for suitability of other board materials or thicknesses. B. Tolerance Maximum allowable bow of the pc board shall be 0.25 mm [.010 in.] over the length of the socket. C. PC Board Layout The mounting and contact holes in the pc board must be precisely located to ensure proper placement and optimum performance of the connector header. Design the pc board using the dimensions provided in Figure 13. The layout shows the top (component) side of the board. NOTE Figure 13 represents a typical pc board layout for this product. For dimensions and hole pattern layout for specific product, obtain the appropriate customer drawing through your Tyco Electronics Representative or refer to the i 12 of 19 telephone numbers at the bottom of page 1. Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 6.35 4.44 + 0.13 [.250] [.175 + .005] (Typ) Polarizing Hole 6.35 No. 2 Circuit [.250] (Typ) No. 1 Circuit 1.78 +0 .08 [.070 + .003] Dia. (Typ) Vertical PC Board Header Layout (15 Position Ref) 3.81 + 0.13 [.150 + .005] B 12.83 7.37 [.505] [.290] 0.635 [.250] 2.54 [.100] A A = 6.35 [.250] X (Total Number of 1.52 +0 .08 Contacts, Minus One). [.060 + .003] Dia. (Typ) B = 14.73 [.580] + A Right-Angle PC Board Header Layout Figure 13 3.11. Contact Hole Configuration The contact holes in the pc board must be prepared as specified in Figure 14. EEE II I EEE II II II EEE I EEE II II EEE I II EEE II II EEE I EEE IIII II II EEE EEE NOTE: The drilled hole diameter must be sized so that the diameter of the finished hole after plating meets the dimensions as shown. Diameter of Finished Hole After Plating Shall be 1.78 +0.08 [.070 +.003] for Vertical Headers and 1.52 +0.08 [.060 +.003] for Right-Angle Headers Drilled Hole Diameter (As Required) Pad Diameter (As Required) FR-4 Material PC Board Thickness Copper Plating (As Required) Tin-Lead Plating Figure 14 Rev P Tyco Electronics Corporation (As Required) 13 of 19 Universal MATE-N-LOK Connectors 114-1010 3.12. Soldering A. Soldering Guidelines Universal MATE-N-LOK Connector Headers can be soldered using wave or equivalent soldering techniques. The temperatures and exposure time shall be within the ranges specified in Figure 15. We recommend using SN60 or SN62 solder for these socket assemblies. SOLDERING TEMPERATURE PROCESS WAVE SOLDERING s 260 Wave Temperature TIME (A Max (At M Temperature) T ) FAHRENHEIT CELSIUS s 500 s 5 Seconds Figure 15 Manual 402-40 provides some guidelines for establishing soldering practices. Refer to Paragraph 2.6, Manuals. NOTE i B. Fluxing The contact solder tines must be fluxed prior to soldering with a mildly active, rosin base flux. Selection of the flux will depend on the type of pc board and other components mounted on the board. Additionally, the flux must be compatible with the wave solder line, manufacturing, health, and safety requirements. Call the Product Information number at the bottom of page 1 for consideration of other types of flux. Some fluxes that are compatible with these sockets are provided in Figure 16. COMMERCIAL DESIGNATION FLUX TYPE ACTIVITY RESIDUE KESTER ALPHA Type RMA (Mildly Activated) Mild Noncorrosive 185/197 611 Center (Activated) Medium May be Corrosive 1544, 1545, 1547 711, 809, 811 Figure 16 C. Cleaning After soldering, removal of fluxes, residues, and activators is necessary. Consult with the supplier of the solder and flux for recommended cleaning solvents. The following is a listing of common cleaning solvents that will not affect the sockets. The sockets will be unaffected by any of these solvents for 5 minutes at room temperature. Cleaners must be free of dissolved flux and other contaminants. We recommend cleaning with the pc board on its edge. If using an aqueous cleaner, we recommend standard equipment such as a soak-tank or an automatic in-line machine. See Figure 17. CLEANER NAME ALPHA 2110 TIME TYPE (Mi (Minutes) ) TEMPERATURES (Maximum) CELSIUS FAHRENHEIT Aqueous 1 132 270 BIOACT EC-7 Solvent 5 100 212 Butyl CARBITOL Solvent 1 Isopropyl Alcohol Solvent 5 100 212 KESTER 5778 Aqueous 5 100 212 KESTER 5779 Aqueous 5 100 212 LONCOTERGE 520 Aqueous 5 100 212 LONCOTERGE 530 Aqueous 5 100 212 Solvent 5 100 212 Terpene Solvent Room Ambient Figure 17 14 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors DANGER 114-1010 Consideration must be given to toxicity and other safety requirements recommended by the solvent manufacturer. Trichloroethylene and Methylene Chloride can be used with no harmful affect to the sockets; however, Tyco Electronics Corporation does not recommend them because of the harmful occupational and environmental effects. Both are carcinogenic (cancer-causing) and Trichloroethylene is harmful to the earth's ozone layer. NOTE If you have a particular solvent that is not listed, contact the Product Information number at the bottom of page 1. i D. Drying When drying clean assemblies and pc boards, air drying of is recommended. Temperature for the sockets should not exceed 105_C [221_F] for a period of five minutes with no degradation to the connector components. Degradation of the sockets could result from extreme temperatures. E. Checking Installed Socket All solder joints should conform to those specified in Test Specification 109-11. 3.13. Repair/Replacement Damaged crimped contacts or housings must be removed, discarded, and replaced with new components. Use an extraction tool to remove individual contacts from connectors for replacement or for relocation to another housing cavity. Extraction Tool 318851-1 is used to extract contacts from the connectors. CAUTION If a damaged contact is evident before the contacts are inserted into the housing, cut the wire in back of the contact and re-terminate the wire end. If the contact or housing is damaged after insertion, remove the contact with the ! CAUTION extraction tool and cut the wire in back of the contact and re-terminate wire end. When removing connector headers from pc boards, reasonable care should be taken to remove the headers straight and in-line in relation to the pc boards. In free-hanging applications, the wires must be supported during removal to ! prevent excess strain on the contacts. Improper removal could result in damage to the wires, housing, contacts, or pc board. 4. QUALIFICATIONS The Universal MATE-N-LOK Connectors are Listed by Underwriters Laboratories Inc. (UL) in File Number E28476, Certified to CSA International in File LR7189, and designed and tested to meet VDE 3980/continuous surveillance. 5. TOOLING This section provides a selection of tools for various application requirements. Modified designs and additional tooling concepts may be available to meet other application requirements. A list of tooling recommendations and instructional material packaged with the tooling covering the full wire size range is provided in Figure 18. NOTE Tool Engineers have designed machines for a variety of application requirements. For assistance in setting up prototype and production line equipment, contact Tool Engineering through your local Tyco Electronics Representative i or call the Tooling Assistance Center number at the bottom of page 1. S Robotic Equipment The robotic equipment must have a true position accuracy tolerance of 0.25 mm [.010 in.] to properly locate the connectors for insertion. This includes gripper and fixture tolerances as well as equipment repeatability. S Board Supports A pc board support must be used to prevent bowing of the pc board during the placement of a connector on the board. It should have flat surfaces with holes or a channel wide enough and deep enough to receive the contact solder tails and boardlocks or other attaching hardware during installation of the connector on the board. Rev P Tyco Electronics Corporation 15 of 19 Universal MATE-N-LOK Connectors 114-1010 S Applicators Applicators are designed for the full wire size range of strip-fed, precision formed contacts, and provide for high volume, heavy duty production requirements. The applicators can be used in bench or floor model power units. NOTE Each applicator is shipped with a metal identification tag attached. DO NOT remove this tag or disregard the information on it. Also, a packet of associated paperwork is included in each applicator shipment. This information i should be read before using the applicator; then it should be stored in a clean, dry area near the applicator for future reference. Some changes may have to be made to the applicators to run in all related power units. Contact the Tooling Assistance Center number at the bottom of page 1 for specific changes. S Power Units A power unit is an automatic or semi-automatic device used to assist in the application of a product. Power unit includes the power source used to supply the force or power to an applicator. S Hand Tools Hand crimping tools are designed for prototype, low-volume applications, and repair. S Extraction Tools Extraction Tools are designed to release the contact inside the connector housing without damaging the housing or contacts. Refer to Instruction Sheet 408-4371 for information on Extraction Tool 318851-1. S Insertion Tools Insertion Tools are designed for contacts crimped to small fragile wire. They are designed to stabilize the contact during insertion. Refer to Instruction Sheet 408-7984 for information on Insertion Tool 455830-1. AMPOMATOR CLS Lead-Making Machines 122500-[ ] and 356500-1, -2 Heavy Duty Quick-Change Mini-Applicator (Typical) AMP-3K 1725950-[ ] AMP-O-LECTRIC Model G" Terminating Machine 354500-[ ] with Optional Stripping Module Figure 18 (cont'd) 16 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 AMP-O-LECTRIC Model G" Terminating Typical CERTI-CRIMP II Machine 354500-[ ] Straight Action Hand Tool PC Board Support (Customer Supplied) Channel (Ref) Holes (Ref) Typical Straight Action Hand Tool Hand Crimping Tool 69710-1 with Die Extraction Tool Assemblies 58380 1804030-1 Robotic Equipment (Typ) Insertion Tool 455830-1 Figure 18 (cont'd) Rev P Tyco Electronics Corporation 17 of 19 Universal MATE-N-LOK Connectors 114-1010 WIRE SIZE INSULATION HAND TOOL APPLICATOR POWER UNIT (AWG) DIAMETER RANGE (DOCUMENT) (408-8040) (DOCUMENT) 30-26 30 26 0.81-1.45 0 81 1 45 [.032-.057] [ 032 057] 58439-1 (408-9591) 58439 1 (408 9591) 466616-2 466616 2 354500-1 (409-5842) 1725950-3, -4 (409-10047) 122500-2, -3 (409-5852) 466320 1 466320-1 356500-1, -2 (409-5878) 24 18 24-18 1 02 2 54 [.040-.100] 1.02-2.54 [ 040 100] 91510 1 (408 91510-1 (408-8547) 8547) 354500-1 (409-5842) 466320-2 } 567216-3 } 567216 2 567216-2 1725950-3, -4 (409-10047) 122500-2, -3 (409-5852) 687763 1 687763-1 356500-1, -2 (409-5878) 20-14 20 14 1.52-3.30 1 52 3 30 [.060-.130] [ 060 130] 91500-1 (408-8547) 91500 1 (408 8547) 354500-1 (409-5842) 687763 2 687763-2 1725950-3, -4 (409-10047) 20-18 3.30-5.08 [.130-.200] 91508-1 (408-8547) --- --122500-2, -3 (409-5852) 687926 1 687926-1 356500-1, -2 (409-5878) 20 14 20-14 3 30 5 08 [.130-.200] 3.30-5.08 [ 130 200] --354500-1 (409-5842) 687926-2 687926 2 1725950-3, -4 (409-10047) 354500-1 (409-5842) 2@18 3 30 5 08 [.130-.200] 3.30-5.08 [ 130 200] --- 1385264 2 1385264-2 1725950-3, -4 (409-10047) 122500-2, -3 (409-5852) 466588 1 466588-1 356500-1, -2 (409-5878) 18 14 18-14 3 30 5 08 [.130-.200] 3.30-5.08 [ 130 200] --354500-1 (409-5842) 466588 2 466588-2 1725950-3, -4 (409-10047) 16-14 3.30-5.08 [.130-.200] 91506-1 (408-8547) --- --122500-2, -3 (409-5852) 466597 1 466597-1 12 10 12-10 5 08 [.200] 5.08 [ 200] Max. Max 69710 1 69710-1 356500-1, -2 (409-5878) { (408 (408-2095) 2095) 354500-1 (409-5842) 466597 2 466597-2 1725950-3, -4 (409-10047) {Hand tool 69710-1 uses die set 58330-1 for 12 AWG and die set 58380-2 for 10 AWG. Refer to Instruction Sheet 408-9433. }Applicators used with product part numbers 770210-1 and 770211-1. Figure 18 (end) 18 of 19 Tyco Electronics Corporation Rev P Universal MATE-N-LOK Connectors 114-1010 6. VISUAL AID Figure 19 shows a typical application of Universal MATE-N-LOK Connectors. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the information in the preceding pages of this specification and in the instructional material shipped with the product or tooling. BELLMOUTH MUST BE VISIBLE CUTOFF TAB MUST BE VISIBLE CUTOFF TAB MUST BE VISIBLE WIRE STRANDS MUST BE VISIBLE IN THIS AREA WIRE STRANDS AND INSULATION MUST BOTH BE VISIBLE IN THIS AREA LOCKING LANCES NOT DEFORMED NO DAMAGE OR DISTORTION IN THIS AREA BELLMOUTH MUST BE VISIBLE HEADER MUST BE VISUALLY SEATED ON PC BOARD CONNECTORS FULLY CLOSED AND LATCHED FIGURE 19. VISUAL AID Rev P Tyco Electronics Corporation 19 of 19