TVS Diodes Surface Mount - 5000W > 5.0SMDJ series 5.0SMDJ Series RoHS Pb e3 Description The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 5000 W Power Dissipation on Infinite Heat Sink at TL=50OC PD 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 5.0 V C Peak Pulse Power Dissipation at TL=25 C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2) O TJ -65 to 150 Storage Temperature Range TSTG -65 to 175 C Typical Thermal Resistance Junction to Lead RJL 15 C/W Typical Thermal Resistance Junction to Ambient RJA 75 C/W Operating Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle = 4 per minute maximum. * 5000W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * SMD low profile surface mount package minimizing PCB footprint * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * EFT protection of data lines in accordance with IEC 61000-4-4 * Built-in strain relief * Glass passivated chip junction * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 5A when VBR min>22V * High temperature to reflow soldering guaranteed: 260C/40sec * VBR @ TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient,) * UL Recognized compound meeting flammability rating V-0 *M eet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) * Recognized to UL 497B as an Isolated Loop Circuit Protector Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Additional Infomarion Functional Diagram Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20 TVS Diodes Surface Mount - 5000W > 5.0SMDJ series Electrical Characteristics (T =25C unless otherwise noted) A Reverse Stand off Voltage VR (Volts) Breakdown Voltage VBR (Volts) @ IT Maximun Maximum Maximum Maximum Maximum Agency Clamping Peak Clamping Maximum Peak Reverse Approval Voltage Pulse Voltage Pulse Temperature Leakage VC@IPP Current IPP VC@IPP Current Coefficient IT IR@VR (10/1000s) (10/1000s) (8/20s) IPP(8/20s) of VBR (%/C) (A) (mA) (V) (A) (V) (A) Test Part Number (Uni) Part Number (Bi) Uni Bi 5.0SMDJ12A 5.0SMDJ12CA 5PEP 5BEP 12.0 13.3 14.7 10 19.9 252.0 25.7 1890.0 800 0.075 5.0SMDJ13A 5.0SMDJ13CA 5PEQ 5BEQ 13.0 14.4 15.9 10 21.5 233.0 27.8 1747.5 500 0.076 X 5.0SMDJ14A 5.0SMDJ14CA 5PER 5BER 14.0 15.6 17.2 10 23.2 216.0 30.0 1620.0 200 0.08 X 5.0SMDJ15A 5.0SMDJ15CA 5PES 5BES 15.0 16.7 18.5 1 24.4 205.0 31.5 1537.5 100 0.083 X 5.0SMDJ16A 5.0SMDJ16CA 5PET 5BET 16.0 17.8 19.7 1 26.0 193.0 33.6 1447.5 50 0.084 X X Marking Min. Max. Current X 5.0SMDJ17A 5.0SMDJ17CA 5PEU 5BEU 17.0 18.9 20.9 1 27.6 181.0 35.7 1357.5 20 0.085 5.0SMDJ18A 5.0SMDJ18CA 5PEV 5BEV 18.0 20.0 22.1 1 29.2 172.0 37.7 1290.0 10 0.088 X 5.0SMDJ20A 5.0SMDJ20CA 5PEW 5BEW 20.0 22.2 24.5 1 32.4 155.0 41.9 850.0 5 0.091 X 5.0SMDJ22A 5.0SMDJ22CA 5PEX 5BEX 22.0 24.4 26.9 1 35.5 141.0 45.9 1057.5 5 0.092 X 5.0SMDJ24A 5.0SMDJ24CA 5PEZ 5BEZ 24.0 26.7 29.5 1 38.9 129.0 50.3 967.5 5 0.092 X 5.0SMDJ26A 5.0SMDJ26CA 5PFE 5BFE 26.0 28.9 31.9 1 42.1 119.0 54.4 892.5 5 0.093 X 5.0SMDJ28A 5.0SMDJ28CA 5PFG 5BFG 28.0 31.1 34.4 1 45.4 110.0 58.7 825.0 5 0.094 X 5.0SMDJ30A 5.0SMDJ30CA 5PFK 5BFK 30.0 33.3 36.8 1 48.4 103.0 62.5 772.5 5 0.096 X 5.0SMDJ33A 5.0SMDJ33CA 5PFM 5BFM 33.0 36.7 40.6 1 53.3 93.9 68.9 704.3 5 0.097 X 5.0SMDJ36A 5.0SMDJ36CA 5PFP 5BFP 36.0 40.0 44.2 1 58.1 86.1 75.1 645.8 5 0.098 X 5.0SMDJ40A 5.0SMDJ40CA 5PFR 5BFR 40.0 44.4 49.1 1 64.5 77.6 83.3 582.0 5 0.099 X 5.0SMDJ43A 5.0SMDJ43CA 5PFT 5BFT 43.0 47.8 52.8 1 69.4 72.1 89.7 540.8 5 0.1 X 5.0SMDJ45A 5.0SMDJ45CA 5PFV 5BFV 45.0 50.0 55.3 1 72.7 68.8 93.9 516.0 5 0.101 X 5.0SMDJ48A 5.0SMDJ48CA 5PFX 5BFX 48.0 53.3 58.9 1 77.4 64.7 100.0 485.3 5 0.101 X 5.0SMDJ51A 5.0SMDJ51CA 5PFZ 5BFZ 51.0 56.7 62.7 1 82.4 60.7 106.5 455.3 5 0.101 X 5.0SMDJ54A 5.0SMDJ54CA 5PGE 5BGE 54.0 60.0 66.3 1 87.1 57.5 112.5 431.3 5 0.102 X 5.0SMDJ58A 5.0SMDJ58CA 5PGG 5BGG 58.0 64.4 71.2 1 93.6 53.5 120.9 401.3 5 0.103 X 5.0SMDJ60A 5.0SMDJ60CA 5PGK 60.0 66.7 73.7 1 96.8 51.7 125.1 387.8 5 0.103 X 5BGK 5.0SMDJ64A 5.0SMDJ64CA 5PGM 5BGM 64.0 71.1 78.6 1 103.0 48.6 133.1 364.5 5 0.104 X 5.0SMDJ70A 5.0SMDJ70CA 5PGP 5BGB 70.0 77.8 86.0 1 113.0 44.3 146.0 332.3 5 0.105 X 5.0SMDJ75A 5.0SMDJ75CA 5PGR 5BGR 75.0 83.3 92.1 1 121.0 41.4 156.3 310.5 5 0.106 X 5.0SMDJ78A 5.0SMDJ78CA 5PGT 5BGT 78.0 86.7 95.8 1 126.0 39.7 162.8 297.8 5 0.106 X 5.0SMDJ85A 5.0SMDJ85CA 5PGV 5BGV 85.0 94.4 104.0 1 137.0 36.5 177.0 273.8 5 0.106 X 5.0SMDJ90A 5.0SMDJ90CA X 5PGX 5BGX 90.0 100.0 111.0 1 146.0 34.3 188.6 257.3 5 0.107 5.0SMDJ100A 5.0SMDJ100CA 5PGZ 5BGZ 100.0 111.0 123.0 1 162.0 30.9 209.3 231.8 5 0.107 X 5.0SMDJ110A 5.0SMDJ110CA 5PHE 5BHE 110.0 122.0 135.0 1 177.0 28.3 228.7 212.3 5 0.107 X 5.0SMDJ120A 5.0SMDJ120CA 5PHG 5BHG 120.0 133.0 147.0 1 193.0 26.0 249.4 195.0 5 0.108 X 5.0SMDJ130A 5.0SMDJ130CA 5PHK 5BHK 130.0 144.0 159.0 1 209.0 24.0 270.0 180.0 5 0.108 X 5.0SMDJ140A 5.0SMDJ140CA 5PHL 5BHL 140.0 156.0 172.0 1 226.1 22.2 292.1 166.5 5 0.108 X 5.0SMDJ150A 5.0SMDJ150CA 5PHM 5BHM 150.0 167.0 185.0 1 243.0 20.6 314.0 154.5 5 0.108 X 5.0SMDJ160A 5.0SMDJ160CA 5PHP 5BHB 160.0 178.0 197.0 1 259.0 19.3 334.6 144.8 5 0.108 X 5.0SMDJ170A 5.0SMDJ170CA 5PHR 5BHR 170.0 189.0 209.0 1 275.0 18.2 355.3 136.5 5 0.108 X For bidirectional type having VR of 20 volts and less, the IR limit is double. For parts without A , the VBR is 10% and VC is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20 TVS Diodes Surface Mount - 5000W > 5.0SMDJ series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR V F IT IT IR Vc VBR VR V IR IT Ipp PPPM VR VBR VC IR VF VR VBR Vc V Ipp Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 1000 Voltage Transients PPPM-Peak Pulse Power (KW) TJ initial = Tamb Voltage or Current Voltage Across TVS Current Through TVS 100 5kW at 10/1000s, 25C 10 1 0.001 Time 0.01 0.1 1 10 td-Pulse Width (ms) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20 TVS Diodes Surface Mount - 5000W > 5.0SMDJ series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) 2 50 0 Transient Thermal Impedance (C/W) Bi-direconal V=0V 1000 Cj(pF) ( ) 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 Figure 6 - Typical Transient Thermal Impedance Uni-direconal V=0V Uni/Bi-direconal V=VR 100 10 100 10 1 0.1 0.01 0.001 1 100 Half Value IPPM IPPM t-Time (ms) 100000 10 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 175 Figure 5 - Typical Junction Capacitance 10000 tr=10sec 1000 0.01 VBR - Reverse Breakdown Voltage(V) 0.1 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 450 100 350 IF-Peak Forward Current(A) IFSM - Peak Forward Surve Current(A) 400 300 250 200 150 10 1 0.1 100 0.01 0.00 50 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 0 1 10 Number of Cycles at 60 Hz 100 VF-Peak Forward Voltage (V) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20 TVS Diodes Surface Mount - 5000W > 5.0SMDJ series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (tL) 60 - 150 seconds Peak Temperature (TP) 260 Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C +0/-5 tp TP Ramp-up TL Temperature (T) Reflow Condition Critical Zone TL to TP tL Ts(max) Ramp-down Ts(min) ts Preheat C Physical Specifications 25C t 25C to Peak Time (t) Environmental Specifications Weight 0.007 ounce, 0.21 grams High Temp. Storage JESD22-A103 Case JEDEC DO214AB. Molded component over glass passivated junction HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Color band denotes positive end (cathode) except Bidirectional. Polarity Matte Tin-plated leads, Solderable per JESD22-B102 Terminal Dimensions Dimensions DO-214AB (SMC J-Bend) A Cathode Band (for uni-directional products only) C A B H D J E F G Dimensions in inches and (millimeters) K L Inches Millimeters Min Max Min Max 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 2.620 D 0.079 0.103 2.060 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 - I 0.129 - 3.300 J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - I Solder Pads (all dimensions in mm) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20 TVS Diodes Surface Mount - 5000W > 5.0SMDJ series Part Numbering System 5.0SMDJ Part Marking System XXX C A Cathode Band F (for uni-directional products only) 5% VBR Voltage Tolerance XXX Bi-Directional YMXXX VR Voltage Series Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options 5.0SMDJxxxXX Component Package DO-214AB 5.0SMDJxxxXX-T7 DO-214AB Part number 3000 Packaging Option Tape & Reel - 16mm tape/13" reel 500 Tape & Reel - 16mm tape/7" reel Quantity Packaging Specification EIA STD RS-481 EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/26/20