PWM5032-001-2S - Aeroflex / Colorado Springs

SCD5031 Rev L

FEATURES

❑Radiation hardness:

- Total dose 1MRad(Si)

- Single event latchup (SEL) immune to 100MeV-cm2/mg

- Single event upset (SEU) 20MeV-cm2/mg

(Upsets found were benign and non-stressful to the PWM or supporting electronic components)

❑CMOS low power design

❑Sleep & enable control lines

❑Optimized for applications: buck, boost, flyback, forward and center tapped push-pull converters

❑Supports current mode or voltage mode operations

❑Selectable 50% / 100% duty cycle

❑Under-Voltage lockout with hysteresis

❑Dual ±1Amp peak totem pole outputs

❑1 MHz maximum – user selectable

❑Low RO error amp

❑Auxiliary op amp with shut down pin

❑Power OK indicator

❑PWM5034 - Same as PMW5032 except straight leads

❑Designed for commercial, industrial and aerospace applications

❑Ceramic 24-lead, hermetic package, .6L x .3W x .13H

- PWM5031/5032 Gull Wing leads

- PWM5034 Straight leads

- Weight: 1.2 g max

- Contact factory for die availability

❑Evaluation board available for test and evaluation. See Aeroflex Application Note AN5031-1

❑DSCC SMD: 5962-06251 approved

NOTE: Aeroflex Plainview does not currently have a DSCC Certified Radiation Hardened Assurance Program

Developed in Partnership with JHU/APL and the Technology Application Group for the

Mars Technology Program; Part of NASA’s Mars Exploration Program

OVERVIEW AND GENERAL OPERATION

The chip is a fixed frequency Pulse Width Modulator based on the industry standard UC1843x Series with significant

enhancements in performance and functionality. The chip operates in either the voltage or current mode and can support a wide

variety of converter topologies.

Radiation hardened by design techniques ensure the chip’s outstanding radiation tolerance (>1MRads) while reducing operating

current by more than an order of magnitude over comparable parts.

The PWM5031 provides an under voltage lockout feature with hysteresis that also provides an output to indicate Power is OK.

An input called Sleep is used to power down the entire chip, the Enable input is used to shut down the Oscillator / Output Drives,

and the Soft input drives the Output to zero. There is also a signal input called ENAUX that is used to disable the output to the

auxiliary op-amp.

The dual output drivers are designed using a Totem Pole output capable of sinking and sourcing 50mA constant current and peak

currents up to 1 Amp to support a large variety of Power MOSFETs.

Additional features that boost the appeal and utility of the part are:

◆Dual break-before-make Totem Pole output stage is employed that virtually eliminates cross conduction and current shoot

through

◆Logic level input that allows the user to select either 50% or 100% maximum duty cycle operation

◆Improved oscillator stage that vastly increases waveform linearity and reduces output voltage error

◆Uncommitted on-board op-amp which can be used for signal conditioning, pulse feedback, or any other user defined

purpose

PWM5031 / PWM5032 RadHard High Speed PWM Controller

Standard Products

www.aeroflex.com/RadHard

November 3, 2008

SCD5031 Rev L 11/3/08 Aeroflex Plainview

FIGURE 1 – Block Diagram

Isense

VFB

Comp

SOFT

Rset

Cset

Error Amp

1.4V

VEE AOUT

Current Sense

Comparators

ENAUX

Internal Enable /

Shutdown Control

Lockout

SLEEP EN 50%PWROK DRVP

OUTA

DRVN

Uncommited

Op-Amp

VCC

Undervoltage

VREF

OUTB

Output

Reference Logic & Control

Functions

Duty Cycle

Limiting

(50% or 100%)

Drive

Internal Bias

Oscillator

PIN NIN

12 15 16 14 13 18,19

22,2321731011 1,24

2.5V

SCD5031 Rev L 11/3/08 Aeroflex Plainview

PWM5031 PWM PIN DESCRIPTION

PIN # SIGNAL NAME FUNCTION DESCRIPTION

VCC Logic Power

2 50% Input selects maximum duty cycle (50% or 100%). Logic ''1'' selects 50% max duty cycle

and Output B is the complement of Output A. Logic ''0'' selects 100% and Output A is

in-phase with Output B.

3 SLEEP This Input shuts down all functions on chip when asserted (Active Hi)

4 COMP Output of the error amplifier. Place compensation network from this pin to VFB to stabilize

converter.

5 VFB Negative Input to the error amplifier

6 ISENSE Input Current sense pin used for current mode control

7 SOFT This High impedance Input is used to limit the error amplifier output voltage. Applying an

RC circuit to this pin provides the standard softstart function. Pull the pin to ground to force

zero duty cycle. This input is internally shorted to ground when Enable (pin 17) is low or

Sleep (pin 3) is high or an Under Voltage is detected.

8 CSET Works with Rset to establish oscillator free running frequency. Place cap from this Input pin

to ground. Can synchronize oscillator by overdriving this pin with an external frequency

source.

9 RSET Works with Cset to establish oscillator free running frequency. Place resistor from this Input

pin to ground.

10 PWROK Logical output of UV lockout circuit -- logic ''1'' indicates chip has valid Vcc

11 VREF Buffered 3V Output reference voltage

12 VEE Logic Ground

13 NIN Auxiliary Op-Amp Inverting Input

14 PIN Auxiliary Op-Amp Non-Inverting Input

15 AOUT Auxiliary Op-Amp Output (Short circuit protected)

16 ENAUX Input Enable of Auxiliary Op-Amp (Active Hi)

17 EN Logic Input that enables the oscillator and output drivers. Reference voltage remains valid

(Active Hi).

DRVN Output stage negative rail

20 OUT B Totem pole Output B

21 OUTA Totem pole Output A

DRVP Output stage positive rail

SCD5031 Rev L 11/3/08 Aeroflex Plainview

ABSOLUTE MAXIMUM RATINGS 1, 4

Operating Temperature Range -55°C to +125°C

Maximum Junction Temperature +135°C

Storage Temperature Range -65°C to +150°C

VCC Supply Voltage 7.0VDC

DRVP Supply Voltage PWM5031 7.0VDC

PWM5032 14.0VDC

Steady State Output Current ±50mA

Peak Output Current (Internally Limited) ±1.0A

Analog Inputs (Pins 5, 6, 13, 14) VEE -0.5V to VCC +0.5V

Power Dissipation at TA = +25°C 500mW

ESD Rating Note 2 450V

Lead Temperature (soldering, 10 seconds) 300°C

NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only;

functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions"

may effect device reliability.

OPERATING CONDITIONS 1, 4

PARAMETER CONDITION SYMBOL MIN TYP MAX UNIT

DC Operating Voltage - VCC 4.5 5.0 5.5 V

Quiescent Current PWM5031 SLEEP @ '0'; EN & ENAUX

@ '1': No loads on Outputs

PWROK, AOUT and VREF

ICC - - 5.8 mA

PWM5032 - - 7.1 mA

Output Drive Voltage PWM5031 - DRVP - - 5.0 V

PWM5032 - - 12.0 V

Output Duty Cycle – Maximum

50% Pin = Logic 0

50% Pin = Logic 1

100% Duty Cycle

50% Duty Cycle

-97*

Thermal Resistance TJC --- - 6.0 °C/W

Sleep Mode - ICCS - - 20 µA

* Dependent on Value of CSET & Operating Frequency

ELECTRICAL CHARACTERISTICS 1, 4

4.5 V < Vcc < 5.5V, -55°C < TA<+125°C, unless otherwise specified

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

Reference Section

Reference Voltage TA = 25°C, IO = -1 mA 3.00 3.05 3.10 V

Line Regulation - ±.1 ±.12 %

Load Regulation 0 < IO<3 mA Note 3 - ±.05 ±.075 %

Thermal Regulation - ±1 ±1.6 %

Output Short Circuit Note 3 - - -40 mA

Oscillator Section

Initial Accuracy Range PWM5031

PWM5032

208.5

190

212

210

219

230

KHz

Frequency Range Note 3 20 - 1,000 KHz

Frequency Stability (Part to Part) - ±1.5 ±2.5 %

Temperature Stability TMIN < TA < TMAX, Note 3 - ±0.5 ±1 %

RSET Range Note 3 50 - - KΩ

CSET Range - - 600 pF

SCD5031 Rev L 11/3/08 Aeroflex Plainview

Error Amp Section

Input Offset Voltage Note 3 - - 3.3 mV

Input Common Mode Voltage Range V

EE +0.2 - VCC -0.2 V

Input Bias Current - - -1.0 µA

Open Loop Voltage Gain (AVOL) 100 - - dB

Unity Gain Bandwidth 1.0 2.0 - MHz

Power Supply Rejection Ratio (PSRR) 60 - - dB

Output Sink Current VFB = 3.0V, VSOFT = 1.1V, Note 3 - - +10 mA

Output Source Current VFB = 2.0V, VSOFT = 5V, Note 3 - - -28 mA

OUT High (Limited by VSOFT)VFB = 2.0V, RL = 15K to GND VSOFT -

0.2

-- V

OUT Low VFB = 3.0V, RL = 15K to +5V - - VEE +0.2 V

Gain (VCOMP/VISENSE) Note 3 2.85 3 3.15 V/V

Current Sense Section

Input Offset Voltage Note 3 - - 3.3 mV

Common Mode Input Voltage VSOFT = 5V, Note 3 & 4 0.1 - 1.0 V

Input Bias Current Note 3 - - 1.0 µA

ISENSE to Output Delay - 80 100 ns

Output Section

Output Low Level ISINK = 1.0mA - - 0.1 V

ISINK = 50mA PWM5031 - - 0.25 V

ISINK = 50mA PWM5032 - - 0.6 V

Output High Level-PWM5031 ISOURCE = 1.0mA, DRVP = 5V 4.9 - - V

ISOURCE = 50mA, DRVP = 5V 4.6 - - V

Output High Level-PWM5032 ISOURCE = 1.0mA, DRVP = 12V 11.9 - - V

ISOURCE = 50mA, DRVP = 12V 11.4 - - V

Peak Output Current Note 3 ±1.0 ±1.35 - A

Steady State Output Current - - 50 mA

Rise Time TA = 25°C, CL = 20pF, DRVP = 5V

Note 3

- 8 18 ns

Fall Time - 6 28 ns

Enable Output Off Delay Note 3 - - 100 ns

Sleep Output Off Delay - - 100 ns

Under Voltage Output Off Delay - - 100 ns

ELECTRICAL CHARACTERISTICS 1, 4 con’t

4.5 V < Vcc < 5.5V, -55°C < TA<+125°C, unless otherwise specified

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

SCD5031 Rev L 11/3/08 Aeroflex Plainview

Auxiliary Amp Section

Input Offset Voltage - - 3.5 mV

Input Common Mode Voltage Range Off VEE or VCC Rail, Note 3 VEE +0.2 - VCC -0.2 V

Input Bias Current Note 3 - - 1.0 µA

AVOL f = 40KHz, 2V < VO<4V, Note 3 100 - - dB

Unity Gain Bandwidth Note 3 1.0 - - MHz

PSRR 4.5V < VCC <5.5V, Note 3 60 70 - dB

Output Sink Current VPIN < VNIN, ENAUX = Hi, Note 3 --+45mA

Output Source Current - - -28 mA

OUT High VPIN > VNIN, ENAUX = Hi, IO = 2mA VCC -0.3 - - V

OUT Low --VEE +0.2 V

Under-Voltage Lockout Section

Start Threshold 3.9 4.1 4.25 V

Operating Voltage After Turn On 3.35 3.5 3.65 V

Digital Inputs

VIL Logic Low, Note 3 - - 0.8 V

VIH Logic High, Note 3 2.0 - - V

Leakage Current - IIN Note 3 - - 100 nA

Digital Ouput (PWROK)

OL Logic low at 1.6mA - - VEE +0.3 V

OH Logic high at -1.6mA VCC -0.6 - - V

Notes

1. All voltages are with respect to Pin 12. All currents are positive into the specified terminal.

2. Meets ESD testing per MIL-STD-883, method 3015, Class 1A.

3. Parameters are guaranteed by design, not tested.

4. All electrical characterizations for the PWM5034 are the same as the PWM5032.

ELECTRICAL CHARACTERISTICS 1, 4 con’t

4.5 V < Vcc < 5.5V, -55°C < TA<+125°C, unless otherwise specified

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

SCD5031 Rev L 11/3/08 Aeroflex Plainview

DETAILED COMPONENT OPERATION AND PERFORMANCE

POWER SUPPLIES

Three I/O pins are used to supply power to the chip:

1) Two DRVP (referenced to DRVN) for the output stage.

2) VCC (referenced to VEE) for all other functions.

For protection against inadvertent over/undervoltages, the chip’s input pins are diode clamped to the supply rails through

current limiting resistors.

Undervoltage Lockout

The chip includes an internal undervoltage lockout circuit with built in hysteresis and a logic level power good indicator.

The positive and negative going thresholds are nominally 4.1V and 3.5V, respectively. If Vcc is below this range, the

oscillator, error amplifier, main comparators, and output drive circuits are all disabled. The power OK indicator is active

high (logic ''1'') when a valid supply voltage is applied.

Shutdown Logic

The chip has two logic level inputs for implementing shutdown functions. Asserting a logic ''1'' on the SLEEP pin disables

all chip functions and puts the chip into a very low power consumption mode. Asserting a logic ''0'' on the EN pin shuts

down all functions except the reference, bias generators, and auxiliary amplifier.

INPUTS OUTPUTS

Sleep EN ENAUX OUTA&B AOUT COMP PWROK Vref

0 0 0 0 0 0 Active 3 VDC

00 1 0Active0Active3 VDC

0 1 0 Active 0 Active Active 3 VDC

0 1 1 Active Active Active Active 3 VDC

1XX00000

X = Don’t care.

Truth Table

3.5V

Von

Voff

4.1V

Vcc

POWER OK

ON/OFF COMMAND

TO REST OF IC

VON

ICC

1.6mA

VOFF VCC

FIGURE 2 –Undervoltage Lockout

SCD5031 Rev L 11/3/08 Aeroflex Plainview

OSCILLATOR

The chip uses two precision current mirrors that alternately charge and discharge an external capacitor to generate an

extremely linear sawtooth oscillator waveform. At the start of each cycle, the charging current, set by the choice of

resistor at the Rset pin, is 1:1 mirrored over to the Cset pin where it charges an external capacitor. When the capacitor

voltage reaches the comparator’s upper threshold (nominally VREF), the comparator switches current mirrors and begins

to discharge the external capacitor. The discharge current is set at roughly five times the charging current to result in fast

discharge and minimal Dead Time. When the voltage reaches the comparator’s lower threshold (0.9V), the comparator

switches back to the charging mirror, powers down the discharge mirror, and the whole process repeats.

The frequency is set by choosing Rset and Cset such that:

Suggested Ranges for Cset and Rset are:

50K ohms < Rset < 300K

10pf < Cset < 600pF

Rset

Cset

GND

FOSC

0.84 RSET

CSET

------------------------------------------------

≈

20KHz FOSC 1MHz

≤≤

FIGURE 3 – Timing Resistance vs Frequency

47pF

100pF

200pF

390pF 200pF

20pF 10pF

10K 100K

Frequency Hz

RSET

160K

140K

120K

100K

80K

60K

40K

Frequency Hz

300K

280K

260K

240K

220K

200K

180K

320K

SCD5031 Rev L 11/3/08 Aeroflex Plainview

Dead Time

The amount of dead time determines the maximum duty cycle that can be achieved. The Dead Time and the frequency of

operation will determine the duty cycle.

Selecting Rset and Cset

To select values for Rset and Cset perform the following steps to insure the smallest Dead Time..

1) Determine what frequency is required for your design.

2) Use Figure 4 to select a capacitor value for Cset that will provide the highest duty cycle (shortest Dead Time) at

the frequency required.

3) Calculate the value of Rset using the formula:

Note small values of Rset increase power consumption for the PWM5031 and small values of Cset may make PCB and

stray capacitance a source of error.

Dead Time 5280 Cset 12pF+()=Duty Cycle 1 Dead Time

1Fosc

⁄

-----------------------------

⎝⎠

⎛⎞

–

Rset

.84 Fosc

Cset

-----------------------------------------=

10K 100K

Duty Cycle

100

47pF

100pF

200pF

20pF

10pF

390pF

Frequency Hz

FIGURE 4 – Duty Cycle vs Frequency

SCD5031 Rev L 11/3/08 Aeroflex Plainview

If desired, the user can synchronize the oscillator to an external frequency source by coupling a pulse train to the Cset

pin:

FIGURE 5 – PWM can be synchronized to external source

with just two additional components.

Operation is similar to the free running case. Cset is alternately charged and discharged by the same current mirrors and

the same comparator and thresholds are used. The only difference is that when a sync pulse is received, the capacitor

voltage is level shifted up and reaches the comparator’s upper threshold voltage before it normally would in the free

running case. If a series of pulses are received with shorter period than that of the free running oscillator, the comparator

will trip in response to the sync pulse and the oscillator will be synchronized. (NOTE: The user must ensure that the sync

pulse does not induce a voltage on CSET that exceeds the PWM5031 voltage rating. If this cannot be guaranteed, a

simple diode clamp to the positive rail should be used to prevent damage to the PWM)

ERROR AMPLIFIER

The main error amplifier is a N-type input folded cascade configuration with a few interesting additions. The positive

input is internally tied to 2.5V derived from the on chip reference. The negative input typically draws less than 1µA and

has a voltage offset of less than 2mV. At 20µA bias current, the amplifier exceeds 2MHz bandwidth and 120dB open

loop gain (see Figure 7).

The amplifier is designed to limit at whatever voltage is applied to the SOFT pin. As mentioned previously, this function

will allow the user to implement a softstart circuit, a controlled turn-on delay, or any number of other useful functions.

Sync Pulse

2nF 24

Cset To P W M

SCD5031 Rev L 11/3/08 Aeroflex Plainview

FIGURE 6 – Current Sense Circuit

Error

1.4V

Current

Comparators

Amp

SOFT

2.5V

CURRENT

SENSE

Sense

Peak Current (Is) is determined by the formula:

A small RC filter may be required to suppress switch transients

ISMAX 1.0V

------------

or if

ISMAX

VSOFT 1.4–

3RS

--------------------------------

VRS

1Volt

then

COMP

FIGURE 7 – Error Amplifier Open-Loop Frequency Response

at +125°C & -55°C

Gain

Frequency Hz (Log Scale)

120

-40

10 100 1K 10K 100K 1M 10M1

+125°C

-55°C

SCD5031 Rev L 11/3/08 Aeroflex Plainview

OUTPUT DRIVE

Dual push-pull outputs OutA and OutB are provided for driving off chip switches. The output stages are identical:

◆Totem Pole configuration

◆Break-before-make switching to prevent harmful cross-conduction spikes

◆Separate positive and negative supply connections to decouple power stage and sensitive logic

◆Near rail-to-rail voltage swing

◆±1A maximum peak current capability (capacitive load)

The outputs have two modes of control depending on whether the 50% toggle option is selected. In the case where the

50% pin is logic low, the outputs are in-phase with each other and the duty cycle is free to take on any value up to 100%.

However, when the 50% pin is asserted high (logic ''1''), the outputs become limited to a maximum 50% duty cycle by

turning off each output on every other clock period of the oscillator. In addition Output A and Output B will never turn

on during the same clock cycle, see Figure 7A below. This would lend itself to a two phase switching system that would

be 180° out of phase..

FIGURE 7A – Output Drive Options

OSC

OUT A

OUT B

OUT A

OUT B

MAX OUTPUT @ 50%

OUTPUT @ 25%

PIN 2 SET LOW, 100% MODE

PIN 2 SET HI, 50% MODE

OUT A

OUT B

MAX OUTPUT @ 100%

SCD5031 Rev L 11/3/08 Aeroflex Plainview

AUXILIARY AMPLIFIER

The chip includes an uncommitted op-amp with independent shutdown feature for use in any user-defined application.

Some possibilities are:

◆Signal conditioning of an isolated configuration feedback voltage

◆Implementation of more sophisticated compensation networks for control loop optimization

The Auxiliary amplifier has a unity gain bandwidth greater than 1MHz and an open loop gain greater than 100dB. The

ENAUX pin is active high such that a logic ''1'' enables the amplifier and logic ''0'' disables it. The amplifier has near

rail-to-rail capability on both the input and output.

A typical single output forward converter application is shown in Figure 9 to aid in the following operational description.

During normal operation, the oscillator jumpstarts each switching cycle by resetting the RS latch, causing the output

stage to go high and turn on M1. Current begins to build linearly through T1 and M1 and a proportional voltage is

developed across the small sense resistor Rs. Switching spikes are filtered by C1 and R1, and the resulting sawtooth

waveform is passed into the PWM to serve as the current comparator input. Meanwhile, a portion of the output voltage

is sensed and compared to the PWM’s internal precision 2.5V reference. The difference is then amplified and level

shifted to serve as the comparator threshold. When the voltage on the ISENSE pin exceeds this threshold, the comparator

fires and resets the latch. The output then turns off until the beginning of the next oscillator cycle when the process

repeats.

FIGURE 8 – Output Sink and Source Saturation Characteristics at +25°C

VSAT

110

500

400

300

200

600

100

Current mA

100

5031

5032

SCD5031 Rev L 11/3/08 Aeroflex Plainview

TYPICAL APPLICATIONS

Like all current mode PWMs, the chip provides built in fault protection by limiting peak switch current on a cycle by

cycle basis. When an overload condition occurs, the sensed current reaches the current trip threshold earlier in the

switching cycle than it otherwise would and thus forces the PWM latch off until the start of the next cycle. The process

repeats until the overload condition is removed and the PWM can return to a normal duty cycle. The chip is capable of

operating in this mode indefinitely without sustaining damage.

There are two ways to set the current limit trip point. One is to simply tailor the sense resistor Rs:

Some users may find the power is dissipated in Rs to be unacceptably high. In this case, the user can fix Rs at a small

value and vary the current comparator threshold instead. Fortunately, the PWM chip provides a very convenient method

for doing so. Because the error amplifier output is internally clamped to the SOFT pin, the user need simply apply the

desired voltage level to the SOFT pin to arbitrarily lower the current comparator threshold.

Recalling that the EA output is level shifted and divided before being applied to the comparator input, the peak current

limit is chosen by applying a voltage VSOFT such that:

Clamping the EA output to the soft pin also makes implementing a softstart ciruit easy. Rsoft and Csoft are connected as

in Figure 9 to provide the SOFT pin an asymptotically rising voltage. Because of the internal clamp on the EA output,

the PWM duty cycle will increase only as fast as the chosen time constant will allow. In this way, excessive duty cycle

and surge currents into the output capacitors are avoided. A transistor may be optionally connected across the softstart

FIGURE 9 – Typical Forward Converter Application

Rset

Cset

SOFT

0.1µF

SOFT

Isolation Barrier

3.3V, 0.5A

Opto-Isolator or

Pulse Transformer

Optional circuit

to force zero

duty cycle

SET

DRVN

COMP

50%

SENSE

Out A

Out B

DRVP

SOFT

REF

+5V

Ipk

1.0Vdc

-------------------=

Ipk

Vsoft 1.4–

3Rs

-------------------------=1.4V Vsoft 4.4V

≤≤

SCD5031 Rev L 11/3/08 Aeroflex Plainview

capacitor to force zero duty cycle on command. This is a particularly convenient method for implementing an externally

controlled turn-on delay.

The discussion so far assumes the user operates the chip in the current mode: switch current is sensed and compared to

the error between the output voltage and a precision reference. Alternatively, the user may wish to implement voltage

mode control in which the control loop is dependent only on the output voltage. The PWM chip readily supports this

configuration with the following modification:

FIGURE 10 – Circuit for implementing voltage mode control.

A portion of the oscillator’s sawtooth waveform is coupled to the ISENSE pin and becomes the input to the comparator

stage. The operation is now identical to the current mode application: when the sawtooth voltage exceeds the amplified

difference between the output and a voltage reference, the comparator fires and latches off the output until the start of the

next cycle.

SELECTED APPLICATION EXAMPLES

The flexibility and performance of the chip makes it suitable for an enormous range of power converter applications –

step-up, step-down, DC-DC, AC-DC, isolated/non-isolated, and many more. This section will cover two of the more

popular power converter applications for which this chip is particularly well suited although many more can be

envisioned.

5V Input, 3.3V Isolated Output (Single Ended Forward Converter)

The isolated step down DC/DC converter is a staple of many satellite and aerospace systems. A common bus distributes

raw primary power to various system loads which must then convert the primary to one or more low voltage secondary

outputs. These outputs are filtered, regulated, and ground isolated from the primary side to keep EMI and undesired

subsystem interaction at a minimum. Figure 9 is one example of a circuit that very efficiently performs this conversion.

The values here were chosen to work for a 5V input and 3.3V output but the circuit topology is general enough to

support an infinite variety of applications. For example, output voltages can be adjusted by changing values of just a few

components. A wider input voltage range can be supported by varying the transformer’s turns ratios and by proper

selection of M1. Thus, a very wide range of power converter applications can be satisfied by simple variations of the

circuit.

At the start of each switching cycle, the PWM output goes high and turns on M1. Energy is coupled across T1’s turns

ratios to the secondary side where it is caught, rectified, and filtered to produce a clean DC voltage. A sampling network

on the output side feeds back a portion of the output across the isolation barrier into the error amplifier negative input.

This feedback can be accomplished in a number of different ways: pulse transformers, optocouplers, or capacitive

coupling are a few methods. The compensation network may need modification depending on the feedback method

chosen. The additional winding and rectifier on T1 are used to reset the transformer core after the PWM latches off M1

to prevent staircase saturation of the core.

Note the chip is powered directly from the main power bus (via a zener and current limit resistor) without the need for

additional bootstrap transformer windings. This is one of the main advantages this PWM chip provides over other

products. This scheme could not be implemented with other chips which draw significantly more current. On the other

hand, supplying bias to our PWM chip is about as simple as it gets.

Out

Isense

Vref

2N2222

Cset

Switch

Current

SCD5031 Rev L 11/3/08 Aeroflex Plainview

5V to 1.8V Buck Converter

A second application is a secondary side, non-isolated buck converter. The circuit takes a high voltage (5V in this case)

and steps down to a lower voltage (5V to 1.8V in this example, although as pointed out above, these values are

completely adjustable with proper component selection). If the output voltage is less than 2.5V the auxiliary amplifier

can be used to provide the gain necessary to get VFB back up to 2.5V.

FIGURE 11 – Buck Converter

The circuit switches M1 twice per cycle, chopping the 5VDC input into a fixed frequency pulse train whose DC average

is the desired output voltage. The LC filter then simply smoothes this pulse train to produce a clean DC output. The

control loop regulates against operating point perturbations (temperature, line, load) by adjusting M1's duty cycle. The

circuit is operated in the voltage mode since switch current is not referenced to circuit ground. Alternatively, a current

transformer may be used to properly reference the ISENSE signal to permit current mode control. An inverter is needed in

the output path to properly drive the P-channel MOSFET. For low current applications (less than -50mA output current),

it may be possible to use the PWM's output drive stage as the switching elements and eliminate M1 and D1 altogether.

SET

NPUT

Rcomp

1V/1.8V/2.5V/3.3V

UTPUT

SOFT

Ccomp

0.1µF

SET

DRVN

COMP

50%

SENSE

Out A

DRVP

SOFT

REF

SCD5031 Rev L 11/3/08 Aeroflex Plainview

FIGURE 12 – Package Pin vs Function

24 VCC

23 DRVP

22 DRVP

21 OUTA

20 OUT B

19 DRVN

18 DRVN

17 EN

16 ENAUX

15 A OUT

14 PIN

13 NIN

VCC 1

50% 2

SLEEP 3

COMP 4

VFB 5

ISENSE 6

SOFT 7

CSET 8

RSET 9

PWROK 10

VREF 11

VEE 12

SCD5031 Rev L 11/3/08 Aeroflex Plainview

.300 MAX

.500

PIN 1 &

ESD IDENT

.614 MAX .110 MAX

(1.300)

.022

1 3 0 MA X

.0 0 8

± . 0 0 1 2

. 6 1 4

MA X . 0 1 9

.3 0 0 .3 9 4

.4 1 9

MA X

1 1 x . 0 5 0 =

. 0 1 5

.3 3 5

MI N

. 0 2 2

±.00 5 . 0 1 2 . 0 2 2 MA X

RE F

.3 5 4

. 0 3 0 RE F

. 5 5 0 ± . 0 0 6

.0 0 8

± . 0 0 1 2

.0 0 8

± . 0 0 1 2

.0 0 8

± . 0 0 1 2

. 6 1 4

MA X . 0 1 9

.3 0 0 .3 9 4

.4 1 9

MA X

1 1 x . 0 5 0 =

P I N 24

. 0 1 5

. 0 1 9

. 0 1 5

. 0 1 9

. 0 1 5

.3 3 5

MI N

. 0 2 2

±.00 5 . 0 1 2 . 0 2 2 MA X

RE F

.3 5 4

0 3 0 RE F

. 5 5 0 ± . 0 0 6

P I N 2 4

1 1 x . 0 5 0 =

. 5 5 0 ± . 0 0 6

1 1 x . 0 5 0 =

. 5 5 0 ± . 0 0 6

PIN 1 &

ESD IDENT

FIGURE 13 – PWM5031 /PWM5032 Flat Package (Gull Wing) Configuration Outline

FIGURE 14 – PWM5034 Flat Package (Straight Leads) Configuration Outline

PLAINVIEW, NEW YORK

Toll Free: 800-THE-1553

Fax: 516-694-6715

SE AND MID-ATLANTIC

Tel: 321-951-4164

Fax: 321-951-4254

INTERNATIONAL

Tel: 805-778-9229

Fax: 805-778-1980

WEST COAST

Tel: 949-362-2260

Fax: 949-362-2266

NORTHEAST

Tel: 603-888-3975

Fax: 603-888-4585

CENTRAL

Tel: 719-594-8017

Fax: 719-594-8468

www.aeroflex.com info-ams@aeroflex.com

Our passion for perform a nce is defined b y three

attributes represented by these three icons :

solution-minded, perform a nce -driven a nd cu stom er-foc use d

Aeroflex Microelectronic Solutions reserves the right to

change at any time without notice the specifications, design,

function, or form of its products described herein. All

parameters must be validated for each customer's application

by engineering. No liability is assumed as a result of use of

this product. No patent licenses are implied.

SCD5031 Rev L 11/3/08

EXPORT CONTROL: EXPOR T WARNING:

This product is controlled for export under the International Traffic in

Arms Regulations (ITAR). A license from the U.S. Department of

State is required prior to the export of this product from the United

States.

Aeroflex’s military and space products are controlled for export under

the International Traffic in Arms Regulations (ITAR) and may not be

sold or proposed or offered for sale to certain countries. (See ITAR

126.1 for complete information.)

CONFIGURATIONS AND ORDERING INFORMATION

MODEL NO. DSCC SMD # SCREENING 1/ CASE

PWM5031-7 - Class C Flat Package, Gull Wing

PWM5031-S

Military Temperature, -55°C to +125°C

Screened in accordance with

MIL-PRF-38534, Class K

PWM5031-Die 2/ Die Size – .136L x .114W inch

PWM5032-7 Class C Flat Package, Gull Wing

PWM5032-S

Military Temperature, -55°C to +125°C

Screened in accordance with

MIL-PRF-38534, Class K

PWM5032-Die 2/ Die Size – .183L x .122W inch

PWM5034-7 Class C Flat Package, Straight Lead

PWM5034-S

Military Temperature, -55°C to +125°C

Screened in accordance with

MIL-PRF-38534, Class K

PWM5032-EM2 Engineering unit, Non-Flight,

Room Temperature, Non-Hermetic Flat Package, Gull Wing

PWM5031-EVAL - See Application note AN5031-1 3/ 8'' x 11'' x 3.25''ht

PWM5032-EVAL

PWM5031-001-1S

PWM5031-001-2S

5962-0625101KXC

5962-0625101KXA

Per DSCC SMD 5962-06251 Flat Package, Gull Wing

PWM5032-001-1S

PWM5032-001-2S

5962-0625102KXC

5962-0625102KXA

PWM5034-001-1S 5962-0625102KYC Flat Package, Straight Lead

1. Level of Screening – Class C = Commercial Flow, Commercial Temp. Range, 0°C to +70°C testing.

2. Each die shall be 100% visually inspected to assure conformance with the applicable die related requirements of MIL-STD-883, method 2010,

cond A or cond B.

3. Application note AN5031-1, titled “ High Speed Pulse Width Modulator Controller Evaluation Board”. Evaluation board PWM5031-EVA L i s

supplied with a PWM5031-EM component and the PWM5032-EVAL board is supplied with a PWM5032-EM component.

PWM5031 Formerly released as ACT5031 Series