UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 HIGH-SPEED PWM CONTROLLER FEATURES D Improved Versions of the UC3823/UC3825 D D D D DESCRIPTION The UC3823A and UC3823B and the UC3825A and UC3825B family of PWM controllers are improved versions of the standard UC3823 and UC3825 family. Performance enhancements have been made to several of the circuit blocks. Error amplifier gain bandwidth product is 12 MHz, while input offset voltage is 2 mV. Current limit threshold is assured to a tolerance of 5%. Oscillator discharge current is specified at 10 mA for accurate dead time control. Frequency accuracy is improved to 6%. Startup supply current, typically 100 A, is ideal for off-line applications. The output drivers are redesigned to actively sink current during UVLO at no expense to the startup current specification. In addition each output is capable of 2-A peak currents during transitions. PWMs Compatible with Voltage-Mode or Current-Mode Control Methods Practical Operation at Switching Frequencies to 1 MHz 50-ns Propagation Delay to Output High-Current Dual Totem Pole Outputs (2-A Peak) Trimmed Oscillator Discharge Current D D Low 100-A Startup Current D Pulse-by-Pulse Current Limiting Comparator D Latched Overcurrent Comparator With Full Cycle Restart BLOCK DIAGRAM CLK/LEB 4 13 VC (60%) RT 5 CT 6 R RAMP 7 EAOUT 3 NI 11 OUTA * OSC T SD PWM LATCH 1.25 V PWM COMPARATOR 14 OUTB 12 PGND 2 E/A 9 mA INV 1 SOFT-START COMPLETE SS 8 CURRENT LIMIT 1.0 V OVER CURRENT ILIM 9 1.2 V RESTART DELAY 0.2 V VCC 15 GND 10 RESTART DELAY LATCH 5V "B" 16V/10V "A" 9.2V/8.4V SD S R R 250 mA FAULT LATCH UVLO VREF 5.1 V ON/OFF * On the UC1823A version, toggles Q and Q are always low. 4V VREF GOOD INTERNAL BIAS 16 5.1 VREF UDG-02091 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004 -2008, Texas Instruments Incorporated UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONTINUED) Functional improvements have also been implemented in this family. The UC3825 shutdown comparator is now a high-speed overcurrent comparator with a threshold of 1.2 V. The overcurrent comparator sets a latch that ensures full discharge of the soft-start capacitor before allowing a restart. While the fault latch is set, the outputs are in the low state. In the event of continuous faults, the soft-start capacitor is fully charged before discharge to insure that the fault frequency does not exceed the designed soft start period. The UC3825 CLOCK pin has become CLK/LEB. This pin combines the functions of clock output and leading edge blanking adjustment and has been buffered for easier interfacing. The UC3825A and UC3825B have dual alternating outputs and the same pin configuration of the UC3825. The UC3823A and UC3823B outputs operate in phase with duty cycles from zero to less than 100%. The pin configuration of the UC3823A and UC3823B is the same as the UC3823 except pin 11 is now an output pin instead of the reference pin to the current limit comparator. "A" version parts have UVLO thresholds identical to the original UC3823 and UC3825. The "B" versions have UVLO thresholds of 16 V and 10 V, intended for ease of use in off-line applications. Consult the application note, The UC3823A,B and UC3825A,B Enhanced Generation of PWM Controllers, (SLUA125) for detailed technical and applications information. ORDERING INFORMATION UVLO MAXIMUM DUTY CYCLE TA -40C 40C to 85C -0C 0C to 70C (1) 9.2 V / 8.4 V 16 V / 10 V SOIC-16(1) (DW) PDIP-16 (N) PLCC-20(1) (Q) SOIC-16 (DW) PDIP-16 (N) PLCC-20(1) (Q) < 100% UC2823ADW UC2823AN UC2823AQ UC2823BDW UC2823BN - < 50% UC2825ADW UC2825AN UC2825AQ UC2825BDW UC2825BN - < 100% UC3823ADW UC3823AN UC3823AQ UC3823BDW UC3823BN - < 50% UC3825ADW UC3825AN UC3825AQ UC3825BDW UC3825BN UC3825BQ The DW and Q packages are also available taped and reeled. Add TR suffix to the device type (i.e., UC2823ADWR). To order quantities of 1000 devices per reel for the Q package and 2000 devices per reel for the DW package. UVLO 9.2 V / 8.4 V MAXIMUM DUTY CYCLE TA -55C 55C to 125C CDIP-16 (J) LCCC-20 (L) < 100% UC1823AJ, UC1823AJ883B, UC1823AJQMLV UC1823AL, UC1823AL883B < 50% UC1825AJ, UC1825AJ883B, UC1825AJQMLV UC1825AL, UC1825AL883B, UC1825ALQMLV PIN ASSIGNMENTS Q OR L PACKAGES (TOP VIEW) 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VREF VCC OUTB VC PGND OUTA GND ILIM EAOUT CLK/LEB NC RT CT 4 3 2 1 20 19 18 5 6 17 16 7 8 15 14 9 10 11 12 13 RAMP SS NC ILIM GND INV NI EAOUT CLK/LEB RT CT RAMP SS NI INV NC VREF VCC DW, J, OR N PACKAGES (TOP VIEW) NC = no connection 2 OUTB VC NC PGND OUTA UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 TERMINAL FUNCTIONS NAME CLK/LEB TERMINAL NO. J or DW Q or L 4 5 I/O DESCRIPTION O Output of the internal oscillator Timing capacitor connection pin for oscillator frequency programming. The timing capacitor should be connected to the device ground using minimal trace length. Output of the error amplifier for compensation Analog ground return pin Input to the current limit comparator Inverting input to the error amplifier Non-inverting input to the error amplifier High current totem pole output A of the on-chip drive stage. High current totem pole output B of the on-chip drive stage. Ground return pin for the output driver stage Non-inverting input to the PWM comparator with 1.25-V internal input offset. In voltage mode operation, this serves as the input voltage feed-forward function by using the CT ramp. In peak current mode operation, this serves as the slope compensation input. Timing resistor connection pin for oscillator frequency programming Soft-start input pin which also doubles as the maximum duty cycle clamp. Power supply pin for the output stage. This pin should be bypassed with a 0.1-F monolithic ceramic low ESL capacitor with minimal trace lengths. CT 6 8 I EAOUT GND ILIM INV NI OUTA OUTB PGND 3 10 9 1 2 11 14 12 4 13 12 2 3 14 18 15 O - I I I O O - RAMP 7 9 I RT SS 5 8 7 10 I I VC 13 17 - VCC 15 19 - Power supply pin for the device. This pin should be bypassed with a 0.1-F monolithic ceramic low ESL capacitor with minimal trace lengths VREF 16 20 O 5.1-V reference. For stability, the reference should be bypassed with a 0.1-F monolithic ceramic low ESL capacitor and minimal trace length to the ground plane. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) UNIT VIN Supply voltage, VC, VCC 22 V IO Source or sink current, DC OUTA, OUTB 0.5 A IO Source or sink current, pulse (0.5 s) OUTA, OUTB 2.2 A INV, NI, RAMP -0.3 V to 7 V ILIM, SS -0.3 V to 6 V Analog inputs Power ground PGND 0.2 V Outputs OUTA, OUTB limits ICLK Clock output current CLK/LEB IO(EA) Error amplifier output current EAOUT 5 mA ISS Soft-start sink current SS 20 mA IOSC Oscillator charging current RT -5 mA TJ Operating virtual junction temperature range -55C to 150C Tstg Storage temperature -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds tSTG Storage temperature Lead temperature 1,6 mm (1/16 inch) from cases for 10 seconds (1) PGND -0.3 V to VC +0.3 V -5 mA -55CC to 150C -65C to 150C 300C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 3 UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 ELECTRICAL CHARACTERISTICS TA = -55C to 125C for the UC1823A/UC1825A, TA = -40C to 85C for the UC2823x/UC2825x, TA = 0C to 70C for the UC3823x/UC3825x, RT = 3.65 k, CT = 1 nF, VCC = 12 V, TA = TJ (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 5.05 5.1 5.15 V REFERENCE, VREF VO Ouput voltage range TJ = 25C, Line regulation 12 V VCC 20 V 2 15 Load regulation 1 mA IO 10 mA 5 20 Total output variation Line, load, temperature Temperature stability(1) T(min) < TA < T(max) 0.2 Output noise voltage(1) 10 Hz < f < 10 kHz 50 Long term stability(1) Short circuit current IO = 1 mA TJ = 125C, 5.03 1000 hours mV 5.17 V 0.4 mV/C VRMS 5 25 mV 30 60 90 mA TJ = 25C 375 400 425 kHz RT = 6.6 k, CT = 220 pF, TA = 25C 0.9 1 1.1 MHz VREF = 0 V OSCILLATOR fOSC Initial accuracy(1) Total variation(1) Voltage stability Temperature stability(1) Line, temperature 350 450 kHz RT = 6.6 k, CT = 220 pF, 0.85 1.15 MHz 12 V < VCC < 20 V T(min) < TA < T(max) High-level output voltage, clock 1% +/- 5% 3.7 4 Low-level output voltage, clock IOSC 0 0.2 Ramp peak 2.6 2.8 3 Ramp valley 0.7 1 1.25 Ramp valley-to-peak 1.6 1.8 2 9 10 11 mA mV Oscillator discharge current RT = OPEN, VCT = 2 V V ERROR AMPLIFIER Input offset voltage 2 10 Input bias current 0.6 3 Input offset current 0.1 1 Open loop gain 1 V < VO < 4 V 60 CMRR Common mode rejection ratio 1.5 V < VCM < 5.5 V 75 95 PSRR Power supply rejection ratio 12 V < VCC < 20 V 85 110 IO(sink) Output sink current VEAOUT = 1 V IO(src) Output source current VEAOUT = 4 V High-level output voltage IEAOUT = -0.5 mA Low-level output voltage IEAOUT = -1 mA Gain bandwidth product f = 200 kHz Slew (1) 4 rate(1) Ensured by design. Not production tested. 1 A A 95 dB 2.5 mA -1.3 -0.5 4.5 4.7 5 0 0.5 1 6 12 Mhz 6 9 V/s V UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 ELECTRICAL CHARACTERISTICS TA = -55C to 125C for the UC1823A/UC1825A, TA = -40C to 85C for the UC2823x/UC2825x, TA = 0C to 70C for the UC3823x/UC3825x, RT = 3.65 k, CT = 1 nF, VCC = 12 V, TA = TJ (unless otherwise noted) PWM COMPARATOR IBIAS Bias current, RAMP VRAMP = 0 V -1 Minimum duty cycle -8 A 0% Maximum duty cycle 85% tLEB Leading edge blanking time RLEB = 2 k, CLEB = 470 pF RLEB Leading edge blanking resistance VCLK/LEB = 3 V VZDC Zero dc threshold voltage, EAOUT VRAMP = 0 V tDELAY Delay-to-output time(1) VEAOUT = 2.1 V, VILIM = 0 V to 2 V step 300 375 450 ns 8.5 10.0 11.5 k 1.10 1.25 1.4 V 50 80 ns 20 A CURRENT LIMIT / START SEQUENCE / FAULT ISS Soft-start charge current VSS Full soft-start threshold voltage IDSCH Restart discharge current ISS Restart threshold voltage IBIAS ILIM bias current ICL Current limit threshold voltage Overcurrent threshold voltage Delay-to-output time, ILIM(1) td VSS= 2.5 V 8 14 4.3 5 100 250 350 A 0.3 0.5 V 15 A 0.95 1 1.05 1.14 1.2 1.26 50 80 IOUT = 20 mA 0.25 0.4 IOUT = 200 mA 1.2 2.2 IOUT = 20 mA 1.9 2.9 2 3 CL = 1 nF 20 45 UC2823B, UC2825B, UC3825B, UC3825B 16 17 9.6 VSS= 2.5 V VILIM = 0 V to 2 V step VILIM = 0 V to 2 V step V V ns OUTPUT Low level output saturation voltage Low-level High level output saturation voltage High-level tr, tf Rise/fall time(1) IOUT = 200 mA V ns UNDERVOLTAGE LOCKOUT (UVLO) Start threshold voltage UC1823A, UC1825A, UC2823A, UC2825A UC3825A, UC3825A 8.4 9.2 Stop threshold voltage UC2823B, UC2825B, UC3825B, UC3825B 9 10 OVLO hysteresis UC1823A, UC1825A, UC2823A, UC2825A UC3825A, UC3825A 0.4 0.8 1.2 UC2823B, UC2825B, UC3825B, UC3825B 5 6 7 100 300 A 28 36 mA V SUPPLY CURRENT Isu Startup current ICC Input current (1) VC = VCC = VTH(start) - 0.5 V Ensured by design. Not production tested. 5 UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 APPLICATION INFORMATION The oscillator of the UC3823A, UC3823B, UC3825A, and UC3825B is a saw tooth. The rising edge is governed by a current controlled by the RT pin and value of capacitance at the CT pin (CCT). The falling edge of the sawtooth sets dead time for the outputs. Selection of RT should be done first, based on desired maximum duty cycle. CT can then be chosen based on the desired frequency (RT) and DMAX. The design equations are: RT + 3V (10 mA) 1 * DMAX CT + 1.6 R T D MAX f (1) Recommended values for RT range from 1 k to 100 k. Control of DMAX less than 70% is not recommended. UDG-95102 Figure 1. Oscillator OSCILLATOR FREQUENCY vs TIMING RESISTANCE 10 M MAXIMUM DUTY CYCLE vs TIMING RESISTANCE 100 DMAX - Maximum Duty Cycle - % f - Frequency - Hz 95 1M 100 k 10 k 1k 10 k RT - Timing Resistance - W Figure 2 6 90 85 80 75 70 100 k 1k 10 k RT - Timing Resistance - W Figure 3 100 k UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 LEADING EDGE BLANKING The UC3823A, UC2823B, UC3825A, and UC3825B perform fixed frequency pulse width modulation control. The UC3823A, and UC3823B outputs operate together at the switching frequency and can vary from zero to some value less than 100%. The UC3825A and UC3825B outputs are alternately controlled. During every other cycle, one output is off. Each output then switches at one-half the oscillator frequency, varying in duty cycle from 0 to less than 50%. To limit maximum duty cycle, the internal clock pulse blanks both outputs low during the discharge time of the oscillator. On the falling edge of the clock, the appropriate output(s) is driven high. The end of the pulse is controlled by the PWM comparator, current limit comparator, or the overcurrent comparator. Normally the PWM comparator senses a ramp crossing a control voltage (error amplifier output) and terminates the pulse. Leading edge blanking (LEB) causes the PWM comparator to be ignored for a fixed amount of time after the start of the pulse. This allows noise inherent with switched mode power conversion to be rejected. The PWM ramp input may not require any filtering as result of leading edge blanking. To program a leading edge blanking (LEB) period, connect a capacitor, C, to CLK/LEB. The discharge time set by C and the internal 10-k resistor determines the blanked interval. The 10-k resistor has a 10% tolerance. For more accuracy, an external 2-k 1% resistor (R) can be added, resulting in an equivalent resistance of 1.66 k with a tolerance of 2.4%. The design equation is: t LEB + 0.5 R o 10 kW C (2) Values of R less than 2 k should not be used. Leading edge blanking is also applied to the current limit comparator. After LEB, if the ILIM pin exceeds the 1-V threshold, the pulse is terminated. The overcurrent comparator, however, is not blanked. It catches catastrophic overcurrent faults without a blanking delay. Any time the ILIM pin exceeds 1.2 V, the fault latch is set and the outputs driven low. For this reason, some noise filtering may be required on the ILIM pin. UDG-95105 Figure 4. Leading Edge Blanking Operational Waveforms 7 UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 UVLO, SOFT-START AND FAULT MANAGEMENT Soft-start is programmed by a capacitor on the SS pin. At power up, SS is discharged. When SS is low, the error amplifier output is also forced low. While the internal 9-A source charges the SS pin, the error amplifier output follows until closed loop regulation takes over. Anytime ILIM exceeds 1.2 V, the fault latch is set and the output pins are driven low. The soft-start cap is then discharged by a 250-A current sink. No more output pulses are allowed until soft-start is fully discharged and ILIM is below 1.2 V. At this point the fault latch resets and the chip executes a soft-start. Should the fault latch get set during soft-start, the outputs are immediately terminated, but the soft-start capacitor does not discharge until it has been fully charged first. This results in a controlled hiccup interval for continuous fault conditions. UDG-95106 Figure 5. Soft-Start and Fault Waveforms ACTIVE LOW OUTPUTS DURING UVLO The UVLO function forces the outputs to be low and considers both VCC and VREF before allowing the chip to operate. UDG-95108 Figure 6. Output Voltage vs Output Current 8 UDG-95106 Figure 7. Output V and I During UVLO UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 CONTROL METHODS Current Mode Voltage Mode UDG-95110 UDG-95109 . Figure 8. Control Methods SYNCHRONIZATION The oscillator can be synchronized by an external pulse inserted in series with the timing capacitor. Program the free running frequency of the oscillator to be 10% to 15% slower than the desired synchronous frequency. The pulse width should be greater than 10 ns and less than half the discharge time of the oscillator. The rising edge of the CLK/LEB pin can be used to generate a synchronizing pulse for other chips. Note that the CLK/LEB pin no longer accepts an incoming synchronizing signal. UDG-95111 Figure 9. General Oscillator Synchronization UDG-95113 Figure 10. Two Unit Interface UDG-95112 Figure 11. Operational Waveforms 9 UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 HIGH CURRENT OUTPUTS Each totem pole output of the UC3823A and UC3823AB, UC3825A, and UC3825B can deliver a 2-A peak current into a capacitive load. The output can slew a 1000-pF capacitor by 15 V in approximately 20 ns. Separate collector supply (VC) and power ground (PGND) pins help decouple the device's analog circuitry from the high-power gate drive noise. The use of 3-A Schottky diodes (1N5120, USD245, or equivalent) as shown in the Figure 13 from each output to both VC and PGND are recommended. The diodes clamp the output swing to the supply rails, necessary with any type of inductive/capacitive load, typical of a MOSFET gate. Schottky diodes must be used because a low forward voltage drop is required. DO NOT USE standard silicon diodes. Although they are single-ended devices, two output drivers are available on the UC3823A and UC3823B devices. These can be paralleled by the use of a 0.5 (noninductive) resistor connected in series with each output for a combined peak current of 4 A. UDG-95114 Figure 12. Power MOSFET Drive Circuit GROUND PLANES Each output driver of these devices is capable of 2-A peak currents. Careful layout is essential for correct operation of the chip. A ground plane must be employed. A unique section of the ground plane must be designated for high di/dt currents associated with the output stages. This point is the power ground to which the PGND pin is connected. Power ground can be separated from the rest of the ground plane and connected at a single point, although this is not necessary if the high di/dt paths are well understood and accounted for. VCC should be bypassed directly to power ground with a good high frequency capacitor. The sources of the power MOSFET should connect to power ground as should the return connection for input power to the system and the bulk input capacitor. The output should be clamped with a high current Schottky diode to both VCC and PGND. Nothing else should be connected to power ground. VREF should be bypassed directly to the signal portion of the ground plane with a good high frequency capacitor. Low ESR/ESL ceramic 1-mF capacitors are recommended for both VCC and VREF. All analog circuitry should likewise be bypassed to the signal ground plane. 10 UC1823A, UC2823A, UC2823B, UC3823A, UC3823B, UC1825A, UC2825A, UC2825B, UC3825A, UC3825B www.ti.com SLUS334E - AUGUST 1995 - REVISED SEPTEMBER 2010 UDG-95115 Figure 13. Ground Planes Diagram OPEN LOOP TEST CIRCUIT This test fixture is useful for exercising many functions of this device family and measuring their specifications. As with any wideband circuit, careful grounding and bypass procedures should be followed. The use of a ground plane is highly recommended. UDG-95116 Figure 14. Open Loop Test Circuit Schematic 11 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) 5962-87681022A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-8768102EA ACTIVE CDIP J 16 1 TBD Call TI Call TI 5962-8768103XA OBSOLETE TO-92 LP 28 TBD Call TI Call TI 5962-89905022A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-8990502EA ACTIVE CDIP J 16 1 TBD Call TI Call TI UC1823AJ ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type UC1823AJ883B ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type UC1823AL ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC1823AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC1823BJ OBSOLETE CDIP J 16 TBD Call TI Call TI UC1823BJ883B OBSOLETE CDIP J 16 TBD Call TI Call TI UC1823BL OBSOLETE LCCC FK 20 TBD Call TI Call TI UC1823BL883B OBSOLETE LCCC FK 20 TBD Call TI Call TI UC1825AJ ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type UC1825AJ883B ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type UC1825AL ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC1825AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type UC1825ALP883B OBSOLETE TO-92 LP 28 TBD Call TI N / A for Pkg Type UC1825BJ OBSOLETE CDIP J 16 TBD Call TI Call TI UC1825BJ883B OBSOLETE CDIP J 16 TBD Call TI Call TI UC1825BL/81047 OBSOLETE TO/SOT L 20 TBD Call TI Call TI UC1825BL883B OBSOLETE LCCC FK 20 TBD Call TI Call TI UC1825BLP883B OBSOLETE TO-92 LP 28 TBD Call TI N / A for Pkg Type UC2823ADW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2823ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2823ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2823ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UC2823AN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2823ANG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2823AQ ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC2823AQG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC2823BDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2823BDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2823BJ OBSOLETE CDIP J 16 TBD Call TI Call TI UC2823BN ACTIVE PDIP N 16 TBD Call TI Call TI UC2823BNG4 ACTIVE PDIP N 16 TBD Call TI Call TI UC2825ADW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2825ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2825ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2825ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2825AN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2825ANG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2825AQ ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC2825AQG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC2825BDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2825BDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 2 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) TBD Lead/ Ball Finish (3) Samples (Requires Login) UC2825BJ OBSOLETE CDIP J 16 UC2825BN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2825BNG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3823ADW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823AN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3823ANG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3823BDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823BDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823BDWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823BDWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3823BN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3823BNG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3825ADW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 3 Call TI MSL Peak Temp Call TI PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) UC3825ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825AN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3825ANG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3825AQ ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC3825AQG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR UC3825BDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825BDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825BDWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825BDWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3825BN ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3825BNG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 4 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1823A, UC1823B, UC1825A, UC1825B, UC2825A, UC3823A, UC3823B, UC3825A, UC3825B : * Catalog: UC3823A, UC3823B, UC3825A, UC3825B * Automotive: UC2825A-Q1 * Enhanced Product: UC2825A-EP * Military: UC1823A, UC1823B, UC1825A, UC1825B * Space: UC1823A-SP, UC1825A-SP NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications * Military - QML certified for Military and Defense Applications * Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UC2823ADWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 UC2825ADWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 UC3823ADWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 UC3823BDWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 UC3825ADWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 UC3825BDWTR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC2823ADWTR SOIC DW 16 2000 367.0 367.0 38.0 UC2825ADWTR SOIC DW 16 2000 367.0 367.0 38.0 UC3823ADWTR SOIC DW 16 2000 367.0 367.0 38.0 UC3823BDWTR SOIC DW 16 2000 367.0 367.0 38.0 UC3825ADWTR SOIC DW 16 2000 367.0 367.0 38.0 UC3825BDWTR SOIC DW 16 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated