HCPL-2231-560E - Avago Technologies

Description

The HCPL-22XX, HCPL-02XX, and HCNW22XX are

optically-coupled logic gates. The HCPL-22XX, and

HCPL-02XX contain a GaAsP LED while the HCNW22XX

contains an AlGaAs LED. The detectors have totem

pole output stages and optical receiver input stages

with built-in Schmitt triggers to provide logic-compatible

waveforms, eliminating the need for additional

waveshaping.

A superior internal shield on the HCPL-2211/12, HCPL-

0211, HCPL-2232 and HCNW2211 guarantees common

mode transient immunity of 10 kV/µs at a common

mode voltage of 1000 volts.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to

prevent damage and/or degradation which may be induced by ESD.

Functional Diagram

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

ANODE

CATHODE

NC GND

VCC

SHIELD

HCPL-2201/11

HCPL-0201/11

HCNW2201/11

ANODE

CATHODE

NC GND

VCC

SHIELD

HCPL-2202/12

ANODE 1

CATHODE 1

CATHODE 2

ANODE 2 GND

VCC

VO1

VO2

SHIELD

HCPL-2231/32

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

HIGH

LOW

HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,

HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,

HCNW2201, HCNW2211

Very High CMR, Wide VCC Logic Ga te Opt oc ouplers

Data Sheet

Features

• 10 kV/µs minimum Common Mode Rejection (CMR) at

VCM = 1000 V (HCPL-2211/2212/0211/2232, HCNW2211)

•Wide operating VCC range: 4.5 to 20 Volts

•300 ns propagation delay guaranteed over the full

temperature range

•5 Mbd typical signal rate

•Low input current (1.6 mA to 1.8 mA)

•Hysteresis

•Totem pole output (no pullup resistor required)

•Available in 8-Pin DIP, SOIC-8, widebody packages

•Guaranteed performance from -40°C to 85°C

•Safety approval

–UL recognized -3750 V rms for 1 minute (5000 V rms

for 1 minute for HCNW22XX) per UL1577

–CSA approved

–IEC/EN/DIN EN 60747-5-2 approved with VIORM = 630

V peak (HCPL-2211/2212 Option 060 only) and

VIORM = 1414 V peak (HCNW22XX only)

•MIL-PRF-38534 hermetic version available

(HCPL-52XX/62XX)

Applications

•Isolation of high speed logic systems

•Computer-peripheral interfaces

•Microprocessor system interfaces

•Ground loop elimination

•Pulse transformer replacement

•High speed line receiver

•Power control systems

Schematic

HCPL-2201/02/11/12

HCPL-0201/11

HCNW2201/11

SHIELD

GND

–

SHIELD

–

HCPL-2231/32

SHIELD

GND

–

The electrical and switching

characteristics of the HCPL-22XX,

HCPL-02XX and HCNW22XX are

guaranteed from -40°C to +85°C

and a VCC from 4.5 volts to 20 volts.

Low IF and wide VCC range allow

compatibility with TTL, LSTTL, and

CMOS logic and result in lower

Selection Guide Small- Widebody

Minimum CMR Input 8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic

On- Single Dual Single Single Single and

dV/dt Current Channel Channel Channel Channel Dual Channel

(V/µs) VCM (V) (mA) Package Package Package Package Packages

1,000 50 1.6 HCPL-2200[1,2] HCPL-0201 HCNW2201

HCPL-2201

HCPL-2202

1.8 HCPL-2231

2,500 400 1.6 HCPL-2219[1,2]

5,000[3] 300[3] 1.6 HCPL-2211 HCPL-0211 HCNW2211

HCPL-2212

1.8 HCPL-2232

1,000 50 2.0 HCPL-52XX[2]

HCPL-62XX[2]

Notes:

1. HCPL-2200/2219 devices include output enable/disable function.

2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications.

3. Minimum CMR of 10 kV/µs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.

power consumption compared to

other high speed couplers. Logic

signals are transmitted with a

typical propagation delay of 150 ns.

Ordering Information

HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL

Recognized with 3750 Vrms for 1 minute per UL1577.

HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577.

All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.

Option

Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN

Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 Quantity

HCPL-2201

-000E no option 300 mil DIP-8 50 per tube

HCPL-2202

-300E -300 X X 50 per tube

HCPL-2211

-500E -500 X X X 1000 per reel

HCPL-2212

-060E -060 X 50 per tube

HCPL-2231

-360E -360 X X X 50 per tube

HCPL-2232

-560E -560 X X X X 1000 per reel

-000E no option SO-8 100 per tube

HCPL-0201

-500E -500 X X X 1500 per reel

HCPL-0211

-060E -060 X 100 per tube

-560E -560 X X X X 1500 per reel

HCNW2201

-000E no option 400 mil 42 per tube

HCNW2211

-300E -300 Widebody X X 42 per tube

-500E -500 DIP-8 X X X 750 per reel

To order, choose a part number from the part number column and combine with the desired option from the

option column to form an order entry.

Example 1:

HCPL-2202-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel

packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant.

Example 2:

HCPL-2202 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant.

Option datasheets are available. Contact your Avago sales representative or authorized distributor for

information.

Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since July 15,

2001 and RoHS compliant will use ‘–XXXE.’

Package Outline Drawings

8-Pin DIP Package (HCPL-2201/02/11/12/31/32)

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)

1.080 ± 0.320

(0.043 ± 0.013) 2.54 ± 0.25

(0.100 ± 0.010)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

5° TYP. 0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

1.78 (0.070) MAX.

1.19 (0.047) MAX.

A XXXXZ

YYWW

DATE CODE

DIMENSIONS IN MILLIMETERS AND (INCHES).

5678

4321

OPTION CODE*

RECOGNITION

TYPE NUMBER

* MARKING CODE LETTER FOR OPTION NUMBERS

"V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

3.56 ± 0.13

(0.140 ± 0.005)

0.635 ± 0.25

(0.025 ± 0.010) 12° NOM.

9.65 ± 0.25

(0.380 ± 0.010)

0.635 ± 0.130

(0.025 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

1.016 (0.040)

1.27 (0.050)

10.9 (0.430)

2.0 (0.080)

LAND PATTERN RECOMMENDATION

1.080 ± 0.320

(0.043 ± 0.013)

3.56 ± 0.13

(0.140 ± 0.005)

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

Small-Outline SO-8 Package (HCPL-0201/11)

8-Pin Widebody DIP Package (HCNW2201/11)

XXX

YWW

8765

4321

5.994 ± 0.203

(0.236 ± 0.008)

3.937 ± 0.127

(0.155 ± 0.005)

0.406 ± 0.076

(0.016 ± 0.003) 1.270

(0.050)BSC

5.080 ± 0.127

(0.200 ± 0.005)

3.175 ± 0.127

(0.125 ± 0.005) 1.524

(0.060)

45° X 0.432

(0.017)

0.228 ± 0.025

(0.009 ± 0.001)

TYPE NUMBER

(LAST 3 DIGITS)

DATE CODE

0.305

(0.012)MIN.

TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)

5.207 ± 0.254 (0.205 ± 0.010)

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.

0.203 ± 0.102

(0.008 ± 0.004)

7°

PIN ONE

0 ~ 7°

7.49 (0.295)

1.9 (0.075)

0.64 (0.025)

LAND PATTERN RECOMMENDATION

11.15 ± 0.15

(0.442 ± 0.006)

1.78 ± 0.15

(0.070 ± 0.006)

5.10

(0.201)MAX.

1.55

(0.061)

MAX.

2.54 (0.100)

TYP.

DIMENSIONS IN MILLIMETERS (INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

7° TYP. 0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

11.00

(0.433)

9.00 ± 0.15

(0.354 ± 0.006)

MAX.

10.16 (0.400)

TYP.

HCNWXXXX

YYWW

DATE CODE

TYPE NUMBER

0.51 (0.021) MIN.

0.40 (0.016)

0.56 (0.022)

3.10 (0.122)

3.90 (0.154)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)

Solder Reflow Temperature Profile

TIME (SECONDS)

TEMPERATURE (°C)

200

100

50 150100 200 250

300

SEC.

50 SEC.

SEC.

160°C

140°C

150°C

PEAK

TEMP.

245°C

PEAK

TEMP.

240°C PEAK

TEMP.

230°C

SOLDERING

TIME

200°C

PREHEATING TIME

150°C, 90 + 30 SEC.

2.5°C ± 0.5°C/SEC.

3°C + 1°C/–0.5°C

TIGHT

TYPICAL

LOOSE

ROOM

TEMPERATURE

PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.

REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.

1.00 ± 0.15

(0.039 ± 0.006)

7° NOM.

12.30 ± 0.30

(0.484 ± 0.012)

0.75 ± 0.25

(0.030 ± 0.010)

11.00

(0.433)

11.15 ± 0.15

(0.442 ± 0.006)

9.00 ± 0.15

(0.354 ± 0.006)

1.3

(0.051)

13.56

(0.534)

2.29

(0.09)

LAND PATTERN RECOMMENDATION

1.78 ± 0.15

(0.070 ± 0.006)

4.00

(0.158)MAX.

1.55

(0.061)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

MAX.

Note: Non-halide flux should be used.

Regulatory Information

The HCPL-22XX/02XX and

HCNW22XX have been approved

by the following organizations:

Recognized under UL 1577,

Component Recognition Program,

File E55361.

CSA

Approved under CSA Component

Acceptance Notice #5, File CA

88324.

IEC/EN/DIN EN 60747-5-2

Approved under:

IEC 60747-5-2:1997 + A1:2002

EN 60747-5-2:2001 + A1:2002

DIN EN 60747-5-2 (VDE 0884

Teil 2):2003-01

(Option 060 and HCNW only)

Recommended Pb-Free IR Profile

217 °C

RAMP-DOWN

6 °C/SEC. MAX.

RAMP-UP

3 °C/SEC. MAX.

150 - 200 °C

260 +0/-5 °C

t 25 °C to PEAK

60 to 150 SEC.

20-40 SEC.

TIME WITHIN 5 °C of ACTU AL

PEAK TEMPERA TURE

PREHEAT

60 to 180 SEC.

smax

smin

TIME

TEMPERATURE

NOTES:

THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.

smax

= 200 °C, T

smin

= 150 °C

Insulation and Safety Related Specifications

8-pin DIP Package 8-Pin DIP Widebody

(300 Mil) SO-8 (400 Mil)

Parameter Symbol Value Value Value Units Conditions

Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals

Air Gap (External to output terminals, shortest

Clearance) distance through air.

Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals

Tracking (External to output terminals, shortest

Creepage) distance path along body.

Minimum Internal 0.08 0.08 1.0 mm Through insulation distance,

Plastic Gap conductor to conductor, usually

(Internal Clearance) the direct distance between the

photoemitter and photodetector

inside the optocoupler cavity.

Minimum Internal NA NA 4.0 mm Measured from input terminals

Tracking (Internal to output terminals, along

Creepage) internal cavity.

Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1

(Comparative

Tracking Index)

Isolation Group IIIa IIIa IIIa Material Group

(DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance with CECC 00802.

Note: Non-halide flux should be used.

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics

(HCPL-2211/2212 Option 060 ONLY)

Description Symbol Characteristic Units

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤300 V rms I-IV

for rated mains voltage ≤450 V rms I-III

Climatic Classification 55/85/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 630 V peak

Input to Output Test Voltage, Method b*

VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 V peak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

VIORM x 1.5 = VPR, Type and sample test, VPR 945 V peak

tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*

(Transient Overvoltage, tini = 10 sec) VIOTM 6000 V peak

Safety Limiting Values

(Maximum values allowed in the event of a failure,

also see Figure 12, Thermal Derating curve.)

Case Temperature TS175 °C

Input Current IS,OUTPUT 230 mA

Output Power PS,OUTPUT 600 mW

Insulation Resistance at TS, VIO = 500 V RS≥109Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN

60747-5-2, for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY)

Description Symbol Characteristic Units

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤600 V rms I-IV

for rated mains voltage ≤1000 V rms I-III

Climatic Classification 55/100/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 1414 V peak

Input to Output Test Voltage, Method b*

VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

VIORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak

tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*

(Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak

Safety Limiting Values

(Maximum values allowed in the event of a failure,

also see Figure 12, Thermal Derating curve.)

Case Temperature TS150 °C

Current (Input Current IF, PS = 0) IS,INPUT 400 mA

Output Power PS,OUTPUT 700 mW

Insulation Resistance at TS, VIO = 500 V RS≥109Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed

description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

Absolute Maximum Ratings

Parameter Symbol Min. Max. Units Note

Storage Temperature TS-55 125 °C

Operating Temperature TA-40 85 °C

Average Forward Input Current IF(AVG) 10 mA 1

Peak Transient Input Current

(≤ 1 µs Pulse Width, 300 pps) IF(TRAN) 1.0 A 1

(≤ 200 µs Pulse Width, HCNW22XX 40 mA

< 1% Duty Cycle)

Reverse Input Voltage VR5V 1

HCNW22XX 3

Average Output Current IO25 mA 1

Supply Voltage VCC 020V

Output Voltage VO-0.5 20 V 1

Total Package Power Dissipation PT210 mW 2

HCPL-223X 294

Output Power Dissipation POSee Figure 7 1

Lead Solder Temperature (Through Hole Parts Only) 260°C for 10 sec.,

1.6 mm below seating plane

HCNW22XX 260°C for 10 sec., up to seating plane

Solder Reflow Temperature Profile See Package Outline Drawings section

(Surface Mount Parts Only)

Recommended Operating Conditions

Parameter Symbol Min. Max. Units

Power Supply Voltage VCC 4.5 20 V

Forward Input Current (ON) IF(ON) 1.6* 5 mA

HCPL-223X 1.8†

Forward Input Voltage (OFF) VF(OFF) -0.8V

Operating Temperature TA-40 85 °C

Junction Temperature TJ-40 125 °C

Fan Out N 4 TTL Loads

*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband.

†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.

Electrical Specifications

-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified.

All Typicals at TA = 25°C. See Note 7.

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Logic Low Output V oltage VOL 0.5 V IOL = 6.4 mA (4 TTL Loads) 1, 3 1

Logic High Output Voltage VOH 2.4 ** V IOH = -2.6 mA 2, 3, 1

2.7 IOH = -0.4 mA

Output Leakage Current IOHH 100 µAV

O = 5.5 V IF = 5 mA 1

500 VO = 20 V

Logic Low Supply ICCL 3.7 6.0 mA VCC = 5.5 V VF = 0 V

4.3 7.0 VCC = 20 V

HCPL-223X 7.4 12.0 VCC = 5.5 V

8.6 14.0 VCC = 20 V

Logic High Supply ICCH 2.4 4.0 mA VCC = 5.5 V IF = 5 mA

2.7 5.0 VCC = 20 V

HCPL-223X 4.8 8.0 VCC = 5.5 V

5.4 10.0 VCC = 20 V

Logic Low Short Circuit IOSL 15 mA VO = VCC = 5.5 V VF = 0 V 1, 3

20 VO = VCC = 20 V

Logic High Short Circuit IOSH -10 mA VCC = 5.5 V IF = 5 mA 1, 3

-20 VCC = 20 V

Input Forward V oltage VF1.5 1.7 V TA = 25°CI

F = 5 mA 4 1

1.85

HCNW22XX 1.5 1.82 TA = 25°C

1.95

Input Reverse Breakdown BVR5VI

R = 10 µA1

HCNW22XX 3 IR = 100 µA

Input Diode Temperature ∆VF-1.7 mV/°CIF = 5 mA

HCNW22XX ∆TA-1.4

Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V 1, 4

HCNW22XX 70

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

**Typical VOH = VCC - 2.1 V.

(VOUT > VCC)

Current

Output Current

VO = GND

Voltage

Coefficient

IO = Open

Output Current

Switching Specifications (AC)

-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.

All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise specified.

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Propagation Delay Time tPHL 150 ns Without Peaking Capacitor 5, 6 1, 6

160 HCNW22XX

150 300 With Peaking Capacitor

Propagation Delay Time tPLH 110 ns Without Peaking Capacitor 5, 6 1, 6

180 HCNW22XX

90 300 With Peaking Capacitor

Output Rise Time (10-90%) tr30 ns 5, 9 1

Output Fall Time (90-10%) tf7ns 5, 9 1

to Logic Low

Output Level

to Logic High

Output Level

Parameter Sym. Device Min. Units Test Conditions Fig. Note

Logic High |CMH|HCPL-2201/02 1,000 V/µs|V

CM| = 50 V VCC = 5 V 10 1, 7

Common Mode HCPL-0201 IF = 1.6 mA†TA = 25°C

Transient HCPL-2231

Immunity HCNW2201

HCPL-2211/12 5,000 V/µs|V

CM| = 300 V

HCPL-0211 IF = 1.6 mA‡

10,000 V/µs|V

CM| = 1 kV

IF = 5.0 mA

Logic Low |CML|HCPL-2201/02 1,000 V/µs|V

CM| = 50 V VF = 0 V 10 1, 7

Common Mode HCPL-0201 VCC = 5 V

Transient HCPL-2231 TA = 25°C

Immunity HCNW2201

HCPL-2211/12 10,000 V/µs|V

CM| = 1 kV

HCPL-0211

HCPL-2232

HCNW2211

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

†IF = 1.8 mA for HCPL-2231.

‡IF = 1.8 mA for HCPL-2232.

HCPL-2232

HCNW2211

Notes:

1. Each channel.

2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.

3. Duration of output short circuit time should not exceed 10 ms.

4. For single devices, input capacitance is measured between pin 2 and pin 3.

5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.

6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of the

output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the trailing

edge of the output pulse.

7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V. CML

is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.

8. For HCPL-2202/12, VO is on pin 6.

9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.

10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage detection

current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN

60747-5-2 Insulation Characteristics Table, if applicable.

11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage detection

current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN

60747-5-2 Insulation Characteristics Table.

12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.

Package Characteristics

Parameter Sym. Min. Typ. Max. Units Test Conditions Fig. Note

Input-Output Momentary VISO 3750 V rms RH < 50%, t = 1 min. 5, 10

HCNW22XX 5000 TA = 25°C

Input-Output Resistance RI-O 1012 ΩVI-O = 500 Vdc 5

HCNW22XX 1012 1013 TA = 25°C

1011 TA = 100°C

Input-Output Capacitance CI-O 0.6 pF f = 1 MHz, 5

HCNW22XX 0.5 0.6 TA = 25°C

Input-Input Insulation II-I 0.005 µARelative Humidity = 45%, 12

Leakage Current t = 5 s, VI-I = 500 V

Resistance (Input-Input) RI-I 1011 ΩVI-I = 500 V 12

Capacitance (Input-Input) CI-I 0.25 pF f = 1 MHz 12

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage

rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level

safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E.

Withstand

Voltage*

VI-O = 0 Vdc

5, 11

– HIGH LEVEL OUTPUT CURRENT – mA

-60

-8

– TEMPERATURE – °C

100

-20

-5

20 60-40 0 40 80

-3

-1

-6

= 4.5 V

= 5 mA

-7

-4

-2 V

= 2.7 V

= 2.4 V

VO – OUTPUT VOLTAGE – V

IF – INPUT CURRENT – mA

1.5

1.00.5

VCC = 4.5 V

TA = 25 °C

IO = 6.4 mA

IO = -2.6 mA

Figure 1. Typical logic low output voltage vs.

temperature. Figure 2. Typical logic high output current vs.

temperature. Figure 3. Typical output voltage vs. forward

input current.

– FORWARD CURRENT – mA

1.1

0.001

– FORWARD VOLTAGE – V

1.0

1000

1.3

0.01

1.51.2 1.4

0.1

= 25 °C

100

HCPL-22XX

HCPL-02XX

–

– FORWARD CURRENT – mA

1.1

0.001

– FORWARD VOLTAGE – V

1.0

1000

1.3

0.01

1.51.2 1.4

0.1

100

HCNW22XX

–

1.6

= 25 °C

Figure 4. Typical input diode forward characteristic.

Figure 5. Circuit for tPLH, tPHL, tr,t

HCPL-2201/11

HCPL-02XX

HCNW22XX

GND

5 V

619 Ω

INPUT

MONITORING

NODE

PULSE GEN.

= t

f =

5 ns

f = 100 kHz

10 % DUTY

CYCLE

= 5 V

= 50

15 pF

THE PROBE AND JIG CAPACITANCES

ARE INCLUDED IN C

1 AND

OUTPUT V

MONITORING

NODE

5 kΩD

120 pF

(ON) 2.15 kΩ

1.6 mA 1.10 kΩ

3 mA 681 Ω

5 mA

ALL DIODES ARE 1N916 OR 1N3064.

HCPL-223X

GND

5 V

619 Ω

INPUT

MONITORING

NODE

PULSE GEN.

= t

f =

5 ns

f = 100 kHz

10 % DUTY

CYCLE

= 5 V

= 50

15 pF

THE PROBE AND JIG CAPACITANCES

ARE INCLUDED IN C

1 AND

OUTPUT V

MONITORING

NODE

5 kΩD

120 pF

(ON) 1.96 kΩ

1.8 mA 1.10 kΩ

3 mA 681 Ω

5 mA

ALL DIODES ARE 1N916 OR 1N3064.

(ON)

50 % I

(ON)

0 mA

PLH

PHL

1.3 V

INPUT I

OUTPUT V

* 0.1 µF BYPASS — SEE NOTE 9.

VOL – LOW LEVEL OUTPUT VOLTAGE – V

-60

TA – TEMPERATURE – °C

100

1.0

-20

0.4

20 60-40 0 40 80

0.6

0.8

0.2

VCC = 4.5 V

VF = 0 V

IO = 6.4 mA

0.1

0.3

0.5

0.7

0.9

tP – PROPAGATION DELAY – ns

-60

TA – TEMPERATURE – °C

100

200

250

-20

100

20 60-40 0 40 80

150

HCNW22XX

VCC = 5.0 V, 20 V

C1 (120 pF) PEAKING CAPACITOR

IS USED. SEE FIGURE 5.

1.6

1.6,

IF (mA)

tPHL

tPLH

Figure 6. Typical propagation delays vs. temperature. Figure 7. Maximum output power per channel

vs. supply voltage.

– HIGH LEVEL OUTPUT VOLTAGE – V

– SUPPLY VOLTAGE – V

10 15

TYPICAL

vs. V

AT I

= -2.6 mA

= 25 °C

, t

– RISE, FALL TIME – ns

-60

– TEMPERATURE – °C

100

-20

20 60-40 0 40 80

= 5 V

Figure 8. Typical logic high output voltage vs.

supply voltage. Figure 9. Typical rise, fall time vs. temperature.

Figure 10. Test circuit for common mode transient immunity and typical waveforms.

VCM (PEAK)

OUTPUT VO

0 V

VOH

|VCM|

VOL

VO (MAX.)*

VO (MIN.)*

SWITCH AT A: IF = 1.6 mA**

SWITCH AT B: VF = 0 V

* SEE NOTE 7, 9.

** I

= 1.8 mA FOR HCPL-2231/32 DEVICES.

– PROPAGATION DELAY – ns

-60

– TEMPERATURE – °C

100

200

250

-20

100

20 60-40 0 40 80

150

(mA)

HCPL-22XX

HCPL-02XX

1.6*

- 5

PLH

PHL

= 5.0 V, 20 V

C1 (120 pF) PEAKING

CAPACITOR IS USED.

SEE FIGURE 5.

= 1.8 mA FOR HCPL-223X

DEVICES.

PO – MAXIMUM OUTPUT POWER

PER CHANNEL (mW)

VCC – SUPPLY VOLTAGE – V

TA = 75 °C

TA = 85 °C

TA =

80°C

HCPL-2201/11

HCPL-02XX

HCNW22XX

0.1 µF

BYPASS

OUTPUT V

MONITORING

NODE

–+ V

PULSE GENERATOR

–

HCPL-2231/32

0.1 µF

BYPASS

OUTPUT V

MONITORING

NODE

–+ V

PULSE GENERATOR

–

OUTPUT POWER – P

, INPUT CURRENT – I

– CASE TEMPERATURE – °C

20050

400

12525 75 100 150

600

800

200

100

300

500

700 P

(mW)

(mA)

HCPL-2211/2212 OPTION 060

175

Figure 11. Typical input threshold current vs. temperature.

Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature

per IEC/EN/DIN EN 60747-5-2.

Figure 13a. Recommended LSTTL to LSTTL circuit where 500 ns propagation delay is sufficient.

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT TTL OR LSTTL

CC2

(+5 V)

UP TO 16 LSTTL LOADS

OR 4 TTL LOADS

* 0.1 µF BYPASS

1.1 kΩ

CC1

(+5 V)

DATA OUTPUT

INPUT CURRENT THRESHOLD – mA

-60

0.5

– TEMPERATURE – °C

100

1.0

-20

0.7

20 60-40 0 40 80

0.8

0.9

0.6

= 5.0 V

= 20 V

HCPL-22XX

HCPL-02XX

(ON)

(OFF)

(ON)

(OFF)

INPUT CURRENT THRESHOLD – mA

-60

0.5

TA – TEMPERATURE – °C

100

1.0

-20

0.7

20 60-40 0 40 80

0.8

0.9

0.6

VCC = 5.0 V

VCC = 20 V

HCNW22XX

IF (ON)

IF (OFF)

IF (ON)

IF (OFF)

OUTPUT POWER PS, INPUT CURRENT IS

TS – CASE TEMPERATURE – °C

175

1000

400

12525 75 100 150

600

800

200

100

300

500

700

900 PS (mW)

IS (mA)

HCNW22XX

Figure 16. Series LED drive with open collector gate (4.7 k resistor shunts IOH from the LED).

Figure 14. LSTTL to CMOS interface circuit.

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA

INPUT

D1 (1N4150) REQUIRED FOR

ACTIVE PULL-UP DRIVER.

1.1 kΩ

VCC1 (+5 V)

VCC

GND

TTL or

LSTTL

Figure 15. Alternative LED drive circuit.

120 pF* 18

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT TTL OR LSTTL

1.1 kΩ

80 Ω*

VCC (+5 V)

OPEN

COLLECTOR

GATE * 120 pF PEAKING CAPACITOR

MAY BE OMITTED AND 80 Ω

RESISTOR MAY BE SHORTED

WHERE 500 ns PROPAGATION

DELAY IS SUFFICIENT.

VCC

GND

4.7 kΩ

Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns.

120 pF 18

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA INPUT TTL OR LSTTL

VCC2 (+5 V)

UP TO 16 LSTTL LOADS

OR 4 TTL LOADS

* 0.1 µF BYPASS

1.1 kΩ

80 Ω

VCC1 (+5 V)

DATA OUTPUT

120

pF* 18

HCPL-2201/11

HCPL-02XX

HCNW22XX

DATA

INPUT TTL OR LSTTL

CC2

(4.5 TO 20 V)

**0.1 µF BYPASS

1.1

kΩ

80 Ω*

CC1

(+5 V)

DATA

OUTPUT

TOTEM

POLE

OUTPUT

GATE * 120 pF PEAKING CAPACITOR

MAY BE OMITTED AND 80 Ω

RESISTOR MAY BE SHORTED

WHERE 500 ns PROPAGATION

DELAY IS SUFFICIENT.

GND

CMOS

CC2

5 V

10 V

15 V

20 V

1.1 kΩ

2.37 kΩ

3.83 kΩ

5.11 kΩ

For product information and a complete list of distributors, please go to our website: www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.

AV01-0556EN July 6, 2007