FTR-K1 SERIES POWER RELAY 2 POLES-2A High insulation/wide gap FTR-C1 Series FEATURES 2 Poles, 2 form C Contact gap: more than 0.6mm High surge voltage: 2500V between open contacts 5000V between coil & contact Complies with Telcordia (former Bellcore) 2nd level surge Dielectric strength: 1500VAC between open contacts 3000VAC between coil and contact Dimensions of large contact gap relay Height: 9.3mm maximum (THT) 9.65mm maximum (SMT) Length: 15mm maximum Width: 7.5mm maximum Conforms to IEC60950/ EN60950/UL1950/CSA C 22.2 No. 950 working voltage 250V (supplementary) High insulation: Clearance: min 2.0mm (coil and contacts) Creepage: min 2.5mm (coil and contacts) High reliability-Bifurcated contacts Low power consumption 280mW (latching type 140mW) RoHS compliant PARTNUMBER INFORMATION [Example] FTR-C1 C (a) (b) A (c) 012 (d) G - B05 (e) (f ) (a) Relay type FTR-C1 : FTR-C1 Series (b) Contact configuration C G S : Through hole type : Surface mount type : Surface mount type reduced mounting area (c) Coil type / enclosure A B : Standard type : Single coil latching type (d) Coil rated voltage 012 : 3....24VDC Coil rating table at page 3 (e) Contact material G : Gold plated silver palladium (f) Tape / reel ordering Nil B05 : Standard packaging (tube) : Tape / reel package, only available for SMT type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-C1CA012G Actual marking: C1CA012G 1 FTR-K1 SERIES FTR-C1 SERIES SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation Other Non-latching FTR-C1 ( ) A Latching FTR-C1 ( ) B Configuration 2 form C Construction Bifurcated Material Gold plated silver palladium Resistance (Initial) Max. 100mOhm at 1A, 6VDC Contact rating resistive 1A, 30VDC / 0.3A, 125VAC / 0.3A, 110VDC Max. Switching Voltage 250VAC / 220VDC Max. Switching Power 62.5VA / 30W Max. Carry Current 2A Min. Switching Load * 10mA, 10mVDC Mechanical Min. 2 x 106 operations Electrical Min. 100 x 103 operations at 0.3A, 125VAC / 1A, 30VD Rated Power 280 to 300mW 140 to 180mW Operate Power 158 to 162mW 158 to 162mW Operating temp range -40 to +85C (no frost) Operate (at nominal voltage) Max. 6ms (without bounce) Release (at nominal voltage) Max. 6ms (without bounce) Resistance (Initial) Min. 1,000MOhm at 500VDC Dielectric strength Open contacts 1500VAC (50/60Hz) 1min Strength Contacts to coil 3,000VAC (50/60Hz) 1min Surge strength Coil to contacts 5,000V, 1.2 x 10s standard wave/6,000V, 1.2 x 50s Clearance open contacts 0.6mm Clearance adjacent contacts 1.0mm Clearance coil and contacts 2.0mm Creepage open contacts 0.6mm Creepage coil and contacts 2.5mm Creepage adjacent contacts 1.0mm Misoperation>1us 10 to 55Hz double amplitude 3.3mm Endurance 10 to 55Hz double amplitude 5mm Misoperation>1us Min. 500m/s2 Endurance Min. 1,000m/s2 Vibration Resistance Shock Weight Approximately 2g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FTR-C1 SERIES COIL RATING Standard type Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * 003 3 32.1 2.25 0.3 4.5 4.5 4.5 72.3 3.38 0.45 6.75 005 5 89.3 3.75 0.5 7.5 012 12 514 9 1.2 18 024 24 1,920 18 2.4 36 Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Set Voltage (VDC) * 003 3 64.0 +2.25 - 2.25 4.5 4.5 4.5 145 +3.38 - 3.38 6.75 005 5 179 +3.75 - 3.75 7.5 012 12 1,029 +9 -9 18 024 24 3,200 +18 - 18 36 Coil Code Must ReleaseMax. Coil Voltage Voltage (VDC) (VDC) * Nominal Coil Power (mW) 280 300 Latching type Coil Code Reset Voltage Max. Coil Voltage (VDC) * (VDC) Nominal Coil Power (mW) 140 180 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63615 0.3A, 125 VAC (resistive) 1 A, 30VDC 0.3A, 110VDC CSA C22.2 No. 14 LR 40304 BSI IEC 60950-1 3 FTR-K1 SERIES FTR-C1 SERIES CHARACTERISTIC DATA 4 FTR-K1 SERIES FTR-C1 SERIES DIMENSIONS AND SCHEMATICS Through hole type Unit: mm TERMINAL DESIGNATIONS RECOMMENDED MOUNTING PAD Standard type (Bottom view de-energized position) Single Coil Latching type (Bottom view reset position) S shows the polarity of set position R shows the polarity of reset position Unit: mm 5 FTR-K1 SERIES FTR-C1 SERIES DIMENSIONS AND SCHEMATICS Surface mount type Unit: mm TERMINAL DESIGNATIONS RECOMMENDED MOUNTING PAD Standard type (Bottom view de-energized position) Single Coil Latching type (Bottom view reset position) S shows the polarity of set position R shows the polarity of reset position Unit: mm 6 FTR-C1 FTR-K1SERIES SERIES DIMENSIONS AND SCHEMATICS Space saving type TERMINAL DESIGNATIONS RECOMMENDED MOUNTING PAD Bottom view de-energized position Single Coil Latching type (Bottom view reset position) S shows the polarity of set position R shows the polarity of reset position Unit: mm 7 FTR-K1SERIES SERIES FTR-C1 RECOMMENDED SOLDERING CONDITIONS SMT (TEMPERATURE PROFILE, please see page 9) Note: 1.Temperature profiles show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. PACKAGING Packaging method (only tape packaging is available) 1. Taping standards: JIS C 0806 and RC-10092B (EIAJ) 2. Tape type: TB2416 or TE2416 3. Reel type: RD24D 4. Quantity of 1 reel: 500 pieces Tape Dimensions: Reel Dimensions: Unit: mm 8 FTR-K1 SERIES FTR-C1 SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. Reflow Solder condition for SMT Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 9 FTR-K1 SERIES FTR-C1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. February 18, 2011 10