[TK634xxAMF] TK634xxAMF Auto Discharge, Ultra Small Package, High RR, Fast Response, Low Noise 200mA CMOS LDO Regulator IC 1-. DESCRIPTION 4-. PIN CONFIGURATION HSON1214-4 The TK634xxAMF is a CMOS LDO regulator with auto discharge function. The package is the very small and thin HSON1214-4. The IC is designed for portable applications with space requirements. The IC can supply 200mA output current. The IC does not require a noise-bypass capacitor. The output voltage is internally fixed from 1.5V to 4.2V. VOut 1 4 VIn GND 2 3 VCont (Top View) 2-. FEATURES Auto discharge function Package: HSON1214-4 No noise bypass capacitor required High ripple rejection Fast transient response Low noise Thermal and over current protection High maximum load current On/Off control High accuracy 5-. BLOCK DIAGRAM VOut 4 VRef COut Thermal & Over Current Protection 3-. APPLICATIONS GND Mobile communication Battery powered system Any electronic equipment AP-MS0036-E-00 1 -1- 2 VIn CIn On/Off Control 3 VCont 2011/02 [TK634xxAMF] 6-. ORDERING INFORMATION T K 6 3 4 A G H L - C Voltage Code (Refer to the following table) Operating Temp. Range Code C : C Rank(standard) Package Code MF : HSON1214-4 Tape/Reel Code L : Left type Solder Composion Code GH : PB Free & Halogen Free Output Voltage Voltage Code Output Voltage Voltage Code Output Voltage Voltage Code 1.5V 15 2.85V 01 3.5V 35 1.8V 18 2.9V 29 4.0V 40 25 30 2.5V 3.0V 2.6V 26 3.1V 31 27 32 2.7V 3.2V 28 33 2.8V 3.3V *If you need a voltage other than the value listed in the above table, please contact Asahi Kasei Microdevices. 7-. ABSOLUTE MAXIMUM RATINGS Ta=25C Parameter Absolute Maximum Ratings Input Voltage Output pin Voltage Control pin Voltage Storage Temperature Range Power Dissipation Symbol Rating Units VIn,MAX VOut,MAX VCont,MAX Tstg -0.3 ~ 6.0 -0.3 ~ VIn+0.3 -0.3 ~ 6.0 -55 ~ 150 V V V C PD 400 mW Conditions Internal Limited Tj=150C *, When mounted on PCB Operating Condition Operational Temperature Range TOP -40 ~ 85 C Operational Voltage Range VOP 1.8 ~ 6.0 V * PD must be decreased at the rate of 3.2mW/C for operation above 25C. The maximum ratings are the absolute limitation values with the possibility of the IC being damaged. When operation exceeds this standard quality can not be guaranteed. AP-MS0036-E-00 -2- 2011/02 [TK634xxAMF] 8-. ELECTRICAL CHARACTERISTICS The parameters with min. or max. values will be guaranteed at Ta=Tj=25C with test when manufacturing or SQC(Statistical Quality Control) methods. The operation between -40 ~ 85C is guaranteed by design. VIn=VOut,TYP+1V, VCont=1.2V, Ta=Tj=25C Value Parameter Symbol Units Conditions MIN TYP MAX Output Voltage VOut V IOut=5mA Refer to TABLE 1 Line Regulation LinReg 0.0 4.0 mV VIn=1V Load Regulation LoaReg mV Refer to TABLE 1 Refer to TABLE 1 Dropout Voltage *1 VDrop mV Refer to TABLE 1 Refer to TABLE 1 Maximum Load Current *2 IOut,MAX 210 350 mA VOut=VOut,TYP0.9 Quiescent Current IQ 35 70 A IOut=0mA, VCont=VIn Standby Current IStandby 0.01 0.1 A VCont=0V GND Pin Current IGND 55 110 A IOut=50mA, VCont=VIn Discharge Resistance RDis 25 VIn=5V, VOut=0.1V, VCont=0V Control Terminal Control Current ICont 0.7 1.4 A VCont=1.2V 1.2 V VOut On state Control Voltage VCont 0.2 V VOut Off state Reference Value Output Voltage / Temp. Output Noise Voltage (TK63428A) Ripple Rejection (TK63428A) Rise Time (TK63428A) VOut/Ta - 100 - VNoise - 35 - Vrms RR - 72 - dB tr - 85 - s ppm/C IOut=5mA COut=1.0F, IOut=30mA, BPF=400Hz~80kHz COut=1.0F, IOut=10mA, f=1kHz COut=1.0F, IOut=30mA VCont: Pulse Wave (100Hz), VCont On VOut95% point *1: For VOut 1.8V, no regulations. *2: The maximum output current is limited by power dissipation. The maximum load current is the current where the output voltage decreases to 90% by increasing the output current at Tj=25C, compared to the output voltage specified at VIn=VOut,TYP+1V. The maximum load current indicates the current at which over current protection turn on. For all output voltage products, the maximum output current for normal operation without operating any protection is 200mA. Accordingly, LoaReg and VDrop are specified on the condition that IOut is less than 200mA. General Note Parameters with only typical values are just reference. (Not guaranteed) The noise level is dependent on the output voltage, the capacitance and capacitor characteristics. AP-MS0036-E-00 -3- 2011/02 [TK634xxAMF] TABLE 1. Preferred Product (TK634xxAMF) Output Voltage Part Number Load Regulation IOut=5 ~ 100mA IOut=5 ~ 200mA Dropout Voltage IOut=100mA IOut=200mA MIN TYP MAX TYP MAX TYP MAX TYP MAX TYP MAX TK63415AMF V 1.475 V 1.500 V 1.525 mV 10 mV 40 mV 19 mV 76 mV - mV - mV - mV - TK63418AMF 1.775 1.800 1.825 10 40 20 80 - - - - TK63425AMF 2.475 2.500 2.525 10 40 20 80 95 145 185 310 TK63426AMF 2.574 2.600 2.626 10 40 20 80 90 145 180 300 TK63427AMF 2.673 2.700 2.727 10 40 20 80 90 140 175 295 TK63428AMF 2.772 2.800 2.828 10 40 20 80 85 135 170 290 TK63401AMF 2.821 2.850 2.879 10 40 20 80 85 135 170 285 TK63429AMF 2.871 2.900 2.929 10 40 20 80 85 135 165 285 TK63430AMF 2.970 3.000 3.030 10 40 20 80 85 130 165 280 TK63431AMF 3.069 3.100 3.131 11 44 21 84 80 130 160 275 TK63432AMF 3.168 3.200 3.232 11 44 21 84 80 125 160 270 TK63433AMF 3.267 3.300 3.333 11 44 21 84 80 125 155 265 TK63435AMF 3.465 3.500 3.535 11 44 21 84 75 120 150 255 TK63440AMF 3.960 4.000 4.040 11 44 21 84 70 115 140 240 Notice. Please contact your authorized Asahi Kasei Microdevices representative for voltage availability. AP-MS0036-E-00 -4- 2011/02 [TK634xxAMF] 9-. TEST CIRCUIT Test circuit for electrical characteristic IIn _ VIn VOut A CIn =1.0F V GND Cont VIn= VOut,TYP+1.0V Notice. COut =1.0F IOut =5mA _ ICont A _ V VOut VCont VIn VOut CIn =1.0F V GND Cont VIn COut =1.0F _ V IOut _ ICont A VOut VCont The limit value of electrical characteristics is applied when CIn=1.0F(Ceramic), COut=1.0F(Ceramic). But CIn, and COut can be used with both ceramic and tantalum capacitors. VOut vs VIn VDrop vs IOut VOut vs IOut VOut vs IOut VOut vs Ta VDrop vs Ta IOut,MAX vs Ta ICont vs VCont , VOut vs VCont ICont vs Ta VCont vs Ta VNoise vs VIn VNoise vs IOut VNoise vs VOut VNoise vs Frequency IIn _ A VIn VOut CIn =1.0F V GND Cont VIn= VOut,TYP+1.0V IQ vs VIn IStandby vs VIn IQ vs Ta Open COut =1.0F _ ICont A VCont VIn VOut CIn =1.0F V GND Cont VIn= VOut,TYP+1.0V _ ICont A IGND IGND vs IOut IGND vs Ta COut =1.0F _ A IOut VCont AP-MS0036-E-00 -5- 2011/02 [TK634xxAMF] VIn= VOut,TYP+1.5V Vripple= 500mVP-P VIn VOut CIn =1.0F V GND Cont RR vs VIn RR vs Frequency RR vs Frequency COut =1.0F IOut =10mA VCont =1.2V VOut,TYP+2V VIn VOut,TYP+1V VCont GND COut =1.0F IOut =5mA VCont =1.2V VIn VOut CIn =1.0F V GND Cont VIn= VOut,TYP+1.0V Line Transient VOut _ V VOut Load Transient COut =1.0F IOut _ V VOut VCont =1.2V VIn VOut CIn =1.0F V Cont GND VIn= VOut,TYP+1.0V AP-MS0036-E-00 VCont =0V 1.2V On/Off Transient COut =1.0F IOut= 0mA or 30mA _ V VOut -6- 2011/02 [TK634xxAMF] 10-. TYPICAL CHARACTERISTICS 10-1-. DC CHARACTERISTICS VOut vs VIn (TK63415AMF) VOut vs VIn (TK63415AMF) 10 40 IOut=0, 5, 50, 100, 150, 200mA IOut=5mA 5 20 0 -5 VOut [mV] VOut [mV] 0 -10 -15 -20 -40 -20 -60 -25 -80 -30 0 1 2 3 4 5 -100 -100 6 0 VIn [V] 300 200 300 200 300 VOut vs VIn (TK63428AMF) 10 40 IOut=0, 5, 50, 100, 150, 200mA IOut=5mA 5 20 0 0 -5 VOut [mV] VOut [mV] 200 VIn -VOut [mV] VOut vs VIn (TK63428AMF) -10 -15 -20 -40 -20 -60 -25 -80 -30 0 1 2 3 4 5 -100 -100 6 0 VIn [V] 100 VIn -VOut [mV] VOut vs VIn (TK63442AMF) VOut vs VIn (TK63442AMF) 10 40 IOut=0, 5, 50, 100, 150, 200mA IOut=5mA 5 20 0 0 -5 VOut [mV] VOut [mV] 100 -10 -15 -20 -40 -20 -60 -25 -80 -30 0 1 2 3 4 5 -100 -100 6 VIn [V] AP-MS0036-E-00 0 100 VIn -VOut [mV] -7- 2011/02 [TK634xxAMF] VOut vs IOut (TK63415AMF) 2 VOut [V] 1.5 1 0.5 0 0 100 200 300 400 500 400 500 400 500 IOut [mA] VOut vs IOut (TK63428AMF) 0 4 -50 3.5 -100 3 -150 2.5 VOut [V] VDrop [mV] VDrop vs IOut (TK63428AMF) -200 2 -250 1.5 -300 1 -350 0.5 -400 0 50 100 150 200 0 250 0 100 IOut [mA] 200 300 IOut [mA] VDrop vs IOut (TK63442AMF) VOut vs IOut (TK63442AMF) 0 6 -50 5 4 -150 VOut [V] VDrop [mV] -100 -200 -250 3 2 -300 1 -350 -400 0 0 50 100 150 200 250 IOut [mA] AP-MS0036-E-00 0 100 200 300 IOut [mA] -8- 2011/02 [TK634xxAMF] VOut vs Ta (TK63415AMF) 10 100 5 80 0 60 -5 40 V Out [mV] VOut [mV] VOut vs IOut (TK63415AMF) -10 -15 -20 20 0 -20 -25 -40 -30 -60 -35 -80 -40 -100 0 50 100 150 200 -50 250 -25 0 10 100 5 80 0 60 -5 40 -10 -15 -20 -40 -60 -35 -80 -40 -100 200 -50 250 -25 0 10 100 5 80 0 60 -5 40 -10 -15 -20 -40 -60 -35 -80 -40 -100 200 -50 250 -25 0 25 75 100 Ta [C] IOut [mA] AP-MS0036-E-00 50 0 -20 -30 150 100 20 -25 100 75 VOut vs Ta (TK63442AMF) V Out [mV] VOut [mV] VOut vs IOut (TK63442AMF) 50 25 Ta [C] IOut [mA] 0 50 0 -20 -30 150 100 20 -25 100 75 VOut vs Ta (TK63428AMF) V Out [mV] VOut [mV] VOut vs IOut (TK63428AMF) 50 50 Ta [C] IOut [mA] 0 25 -9- 2011/02 [TK634xxAMF] IOut,MAX vs Ta (TK63415AMF) IOut,MAX [mA] 400 300 200 -50 -25 0 25 50 75 100 50 75 100 50 75 100 Ta [C] VDrop vs Ta (TK63428AMF) IOut,MAX vs Ta (TK63428AMF) 0 400 -50 IOut=100mA -150 IOut,MAX [mA] VDrop [mV] -100 IOut=200mA -200 -250 300 -300 -350 -400 -50 -25 0 25 50 75 200 -50 100 -25 0 Ta [C] Ta [C] VDrop vs Ta (TK63442AMF) IOut,MAX vs Ta (TK63442AMF) 0 400 -50 IOut=100mA -100 IOut=200mA IOut,MAX [mA] VDrop [mV] 25 -150 -200 -250 300 -300 -350 -400 -50 -25 0 25 50 75 200 -50 100 Ta [C] AP-MS0036-E-00 -25 0 25 Ta [C] - 10 - 2011/02 [TK634xxAMF] IQ vs VIn (TK63415AMF) IStandby vs VIn (TK63415AMF) 10 100 VCont=VIn VCont=0V 9 80 8 70 7 60 6 IStandby [nA] IQ [A] 90 50 40 30 5 4 3 2 20 10 1 0 0 0 1 2 3 4 5 6 0 1 2 IQ vs VIn (TK63428AMF) 5 6 IStandby vs VIn (TK63428AMF) 100 10 VCont=VIn 90 VCont=0V 9 80 8 70 7 60 6 IStandby [nA] IQ [A] 4 VIn [V] VIn [V] 50 40 30 20 5 4 3 2 10 1 0 0 0 1 2 3 4 5 6 0 1 2 3 4 5 6 VIn [V] VIn [V] IQ vs VIn (TK63442AMF) IStandby vs VIn (TK63442AMF) 100 10 VCont=VIn 90 VCont=0V 9 80 8 70 7 60 6 IStandby [nA] IQ [A] 3 50 40 30 20 5 4 3 2 10 1 0 0 0 1 2 3 4 5 6 1 2 3 4 5 6 VIn [V] VIn [V] AP-MS0036-E-00 0 - 11 - 2011/02 [TK634xxAMF] IGND vs IOut (TK63415AMF) IQ vs Ta (TK63415AMF) 100 200 VCont=VIn 160 80 140 70 120 60 100 80 50 40 60 30 40 20 20 10 0 0 0 50 100 150 200 VCont=VIn 90 IQ [A] IGND [A] 180 250 -50 -25 0 IOut [mA] 160 80 140 70 120 60 100 80 50 40 60 30 40 20 20 10 0 0 50 100 150 200 VCont=VIn 90 IQ [A] IGND [A] 100 100 VCont=VIn 180 250 -50 -25 0 IOut [mA] 25 50 75 100 Ta [C] IGND vs IOut (TK63442AMF) IQ vs Ta (TK63442AMF) 100 200 VCont=VIn 180 160 80 140 70 120 60 100 80 50 40 60 30 40 20 20 10 0 0 50 100 150 200 250 IOut [mA] AP-MS0036-E-00 VCont=VIn 90 IQ [A] IGND [A] 75 IQ vs Ta (TK63428AMF) 200 0 50 Ta [C] IGND vs IOut (TK63428AMF) 0 25 -50 -25 0 25 50 75 100 Ta [C] - 12 - 2011/02 [TK634xxAMF] IGND vs Ta (TK63415AMF) ICont vs VCont, VOut vs VCont (TK63415AMF) 100 2 2 VCont=VIn , IOut=50mA 90 VOut 80 1.5 50 40 1.5 1 1 VOut [V] 60 ICont [A] IGND [A] 70 30 0.5 20 0.5 ICont 10 -25 0 25 50 75 0 100 0 0 0.5 1 1.5 VCont [V] Ta [C] IGND vs Ta (TK63428AMF) ICont vs VCont, VOut vs VCont (TK63428AMF) 100 2 4 VCont=VIn , IOut=50mA 90 80 VOut 1.5 70 60 ICont [A] IGND [A] 2 50 40 3 1 2 VOut [V] 0 -50 30 0.5 20 1 ICont 10 0 -50 -25 0 25 50 75 0 100 0 0 0.5 1 1.5 2 VCont [V] Ta [C] IGND vs Ta (TK63442AMF) ICont vs VCont, VOut vs VCont (TK63442AMF) 100 2 8 VCont=VIn , IOut=50mA 90 VOut 60 ICont [A] IGND [A] 70 50 40 1.5 6 1 4 VOut [V] 80 30 0.5 20 2 ICont 10 0 -50 -25 0 25 50 75 0 100 0.5 1 1.5 2 VCont [V] Ta [C] AP-MS0036-E-00 0 0 - 13 - 2011/02 [TK634xxAMF] VCont vs Ta (TK63415AMF) ICont vs Ta (TK634xxAMF) 1.4 1 VCont=1.2V 1.2 0.75 ICont [] VCont [V] 1 0.8 0.6 0.4 0.5 0.25 0.2 0 -50 -25 0 25 50 75 0 100 Ta [C] -50 -25 0 25 50 75 100 Ta [C] VCont vs Ta (TK63428AMF) 1.4 1.2 VCont [V] 1 0.8 0.6 0.4 0.2 0 -50 -25 0 25 50 75 100 50 75 100 Ta [C] VCont vs Ta (TK63442AMF) 1.4 1.2 VCont [V] 1 0.8 0.6 0.4 0.2 0 -50 -25 0 25 Ta [C] AP-MS0036-E-00 - 14 - 2011/02 [TK634xxAMF] 10-2-. AC CHARACTERISTICS RR vs VIn (TK63415AMF) RR vs Frequency (TK63415AMF) 0 0 Vripple=0.1Vp-p, f=1kHz -10 -20 -40 -50 -40 -50 -60 -60 -70 -70 -80 -80 COut=1.0F(cer.) -90 -90 -100 COut=1.0F(tant.) -30 RR [dB] RR [dB] -20 IOut= 200mA 150mA 100mA 50mA 10mA -30 IOut=10mA -10 0 0.5 1 1.5 2 2.5 3 -100 100 3.5 1k RR vs VIn (TK63428AMF) -20 -20 -50 -40 -50 -60 -60 -70 -70 -80 -80 -90 -90 0 0.5 1 COut=1.0F(tant.) -30 RR [dB] RR [dB] -40 IOut=10mA -10 IOut= 200mA 150mA 100mA 50mA 10mA -30 1.5 2 2.5 3 -100 100 3.5 COut=1.0F(cer.) 1k 10k 100k 1M Frequency [Hz] VIn-VOut,TYP [V] RR vs VIn (TK63442AMF) RR vs Frequency (TK63442AMF) 0 0 Vripple=0.1Vp-p, f=1kHz -10 IOut=10mA -10 -20 -20 -50 -60 RR [dB] -40 COut=1.0F(tant.) -30 IOut= 200mA 150mA 100mA 50mA 10mA -30 RR [dB] 1M 0 Vripple=0.1Vp-p, f=1kHz -10 -40 -50 -60 -70 -70 -80 -80 COut=1.0F(cer.) -90 -90 -100 100k RR vs Frequency (TK63428AMF) 0 -100 10k Frequency [Hz] VIn-VOut,TYP [V] 0 0.5 1 1.5 2 -100 100 2.5 10k 100k 1M Frequency [Hz] VIn-VOut,TYP [V] AP-MS0036-E-00 1k - 15 - 2011/02 [TK634xxAMF] RR vs Frequency (TK63415AMF) The ripple rejection (RR) characteristic depends on the characteristic and the capacitance value of the capacitor connected to the output side. The RR characteristic of 50kHz or more varies greatly with the capacitor on the output side and PCB pattern. If necessary, please confirm stability of your design. 0 IOut=10mA -10 -20 RR [dB] -30 -40 -50 -60 COut=0.68F(cer.) 1.0F(cer.) F(cer.) -70 -80 -90 -100 100 1k 10k 100k 1M Frequency [Hz] RR vs Frequency (TK63428AMF) 0 IOut=10mA -10 -20 RR [dB] -30 -40 -50 -60 COut=0.68F(cer.) 1.0F(cer.) F(cer.) -70 -80 -90 -100 100 1k 10k 100k 1M Frequency [Hz] RR vs Frequency (TK63442AMF) 0 IOut=10mA -10 -20 RR [dB] -30 -40 -50 -60 COut=0.68F(cer.) 1.0F(cer.) F(cer.) -70 -80 -90 -100 100 1k 10k 100k 1M Frequency [Hz] AP-MS0036-E-00 - 16 - 2011/02 [TK634xxAMF] VNoise vs VIn (TK63415AMF) VNoise vs IOut (TK63415AMF) 100 100 IOut=30mA 90 90 80 VNoise [Vrms] VNoise [Vrms] 80 70 60 50 40 70 60 50 40 30 30 20 20 10 10 0 0 1 2 3 4 5 0 6 0 50 VIn [V] 200 250 200 250 200 250 VNoise vs IOut (TK63428AMF) 100 100 IOut=30mA 90 90 80 80 VNoise [Vrms] VNoise [Vrms] 150 IOut [mA] VNoise vs VIn (TK63428AMF) 70 60 50 40 70 60 50 40 30 30 20 20 10 10 0 0 2.5 3 3.5 4 4.5 VIn [V] 5 5.5 6 0 50 100 150 IOut [mA] VNoise vs VIn (TK63442AMF) VNoise vs IOut (TK63442AMF) 100 100 IOut=30mA 90 90 80 80 VNoise [Vrms] VNoise [Vrms] 100 70 60 50 40 70 60 50 40 30 30 20 20 10 10 0 4 4.5 5 5.5 0 6 VIn [V] AP-MS0036-E-00 0 50 100 150 IOut [mA] - 17 - 2011/02 [TK634xxAMF] VNoise vs VOut (TK634xxAMF) VNoise vs Frequency (TK63415AMF) 100 10 IOut=30mA 90 IOut=10mA 70 VNoise [V/Hz] VNoise [Vrms] 80 60 50 40 30 1 0.1 20 10 0 1.5 2 2.5 3 3.5 4 0.01 10 4.5 100 VOut [V] 1k 10k 100k Frequency [Hz] VNoise vs Frequency (TK63428AMF) VNoise [V/Hz] 10 IOut=10mA 1 0.1 0.01 10 100 1k 10k 100k Frequency [Hz] VNoise vs Frequency (TK63442AMF) VNoise [V/Hz] 10 IOut=10mA 1 0.1 0.01 10 100 1k 10k 100k Frequency [Hz] AP-MS0036-E-00 - 18 - 2011/02 [TK634xxAMF] 10-3-. TRANSIENT CHARACTERISTICS Line Transient (TK63415AMF) VIn Load Transient (IOut=5100mA) (TK63415AMF) 1V/div 3.5V IOut 2.5V 100mA 100mA/div 5mA IOut=50, 100, 200mA VOut 100mV/div COut=0.68, 1.0, 2.2F VOut 10mV/div 20sec/div 20sec/div Time Time Line Transient (TK63428AMF) VIn Load Transient (IOut=5100mA) (TK63428AMF) 1V/div 4.8V IOut 3.8V 100mA 100mA/div 5mA IOut=50, 100, 200mA VOut 100mV/div COut=0.68, 1.0, 2.2F VOut 10mV/div 20sec/div 20sec/div Time Time Line Transient (TK63442AMF) VIn Load Transient (IOut=5100mA) (TK63442AMF) 1V/div 6.2V IOut 5.2V 100mA 100mA/div 5mA IOut=50, 100, 200mA VOut 100mV/div COut=0.68, 1.0, 2.2F VOut AP-MS0036-E-00 10mV/div 20sec/div 20sec/div Time Time - 19 - 2011/02 [TK634xxAMF] Load Transient (IOut=0 or 5100mA) (TK63415AMF) Load Transient (0100mA) (TK63428AMF/M5) 100mA IOut VOut 100mA 100mA/div 0 or 5mA 0 100mA IOut VOut 0 or 5mA 100mA/div 0 100mA 100mV/div 100mV/div 5 100mA 5 100mA 10msec/div 10sec/div Time Time Load Transient (IOut=0 or 5100mA) (TK63428AMF) Load Transient 0100mA) (TK63428AMF/M5) 100mA IOut 100mA 100mA/div 0 or 5mA IOut 0 100mA VOut VOut 0 or 5mA 100mA/div 0 100mA 100mV/div 100mV/div 5 100mA 5 100mA 10msec/div 10sec/div Time Time Load Transient (IOut=0 or 5100mA) (TK63442AMF) Load Transient (0100mA) (TK63428AMF/M5) 100mA IOut VOut 100mA 100mA/div 0 or 5mA 0 100mA IOut VOut 0 or 5mA 100mA/div 0 100mA 100mV/div 5 100mA AP-MS0036-E-00 100mV/div 5 100mA 10msec/div 10sec/div Time Time - 20 - 2011/02 [TK634xxAMF] On/Off Transient (VCont=01.2V) (TK63415AMF) On/Off Transient (VCont=1.20V) (TK63415AMF) IOut=0mA IOut=30mA VCont VOut 1V/div VCont 500mV/div VOut COut=0.68, 1.0, 2.2F IIn 200mA/div 1V/div COut=0.68, 1.0, 2.2F 0.5V/div IIn 200mA/div 40sec/div 40sec/div Time Time On/Off Transient (VCont=01.2V) (TK63428AMF) On/Off Transient (VCont=1.20V) (TK63428AMF) IOut=0mA IOut=30mA VCont VOut 1V/div VCont 1V/div VOut COut=0.68, 1.0, 2.2F IIn 200mA/div 1V/div COut=0.68, 1.0, 2.2F 1V/div IIn 200mA/div 40sec/div 40sec/div Time Time On/Off Transient (VCont=01.2V) (TK63442AMF) On/Off Transient (VCont=1.20V) (TK63442AMF) IOut=0mA IOut=30mA VCont VOut 1V/div VCont 2V/div VOut COut=0.68, 1.0, 2.2F IIn AP-MS0036-E-00 200mA/div 1V/div COut=0.68, 1.0, 2.2F 2V/div IIn 200mA/div 40sec/div 40sec/div Time Time - 21 - 2011/02 [TK634xxAMF] 11-. PIN DESCRIPTION Pin No. Pin Description Internal Equivalent Circuit Description Output Terminal VIn 1 VOut On/Off Control 2 VOut ESD protection GND Terminal Control Terminal GND ESD protection 3 VCont VCont VCont > 1.2V : On VCont < 0.2V : Off The pull-down resistor (about 1.65M) is built-in. 1.65M 4 AP-MS0036-E-00 VIn Input Terminal - 22 - 2011/02 [TK634xxAMF] 12-. APPLICATIONS INFORMATION 12-1-. Stability Linear regulators require input and output capacitors in order to maintain the regulator's loop stability. If 0.68F capacitors are connected to the input side and the output side, the IC provides stable operation. However, it is recommended to use as large a value capacitor as is practical. The output noise and the ripple noise decrease as the value of the capacitor increases. A recommended value of the application is as follows. CIn0.68F, COut0.68F It is not possible to determine this indiscriminately. Please confirm the stability in your design. Fig12-1: Capacitor in the application VIn VOut TK634xxA CIn0.68F For evaluation Kyocera : CM05X5R105K10AB Fig12-3: ex. Ceramic Capacitance vs Voltage, Temperature Capacitance vs Voltage 100 90 80 70 60 50 B Curve CAP(%) COut0.68F Fig.12-2 shows the stable operation area of output current and the equivalent series resistance (ESR) with a ceramic capacitor of 0.68F. ESR of the output capacitor must be in the stable operation area. Please select the best output capacitor according to the voltage and current used. The stability of the regulator improves as the value of the output side capacitor increases (the stable operation area extends.) Please use as large a value capacitor as is practical. VCont F Curve 0 2 4 6 8 10 12 Bias Voltage(V) Capacitance vs Temperature 100 90 80 70 60 50 B Curve CAP(%) Fig12-2: Output Current vs Stable Operation Area -40~+85C 100 F Curve -50 -25 0 25 50 75 100 Ta(C) ESR [] 10 Generally, a ceramic capacitor has both a temperature characteristic and a voltage characteristic. Please consider both characteristics when selecting the part. The B curves are the recommended characteristics. Stable Area 1 0.1 0.01 0 50 100 150 200 IOut [mA] AP-MS0036-E-00 - 23 - 2011/02 [TK634xxAMF] Fig12-5: Derating Curve 12-2-. Layout PD(mW) 12-4: Layout example VIn 900 VCont 400 VOut (Top View) VOut -3.2mW/C PCB size (7mmx8mmx0.8mm) GND PCB Material: Glass epoxy Size: 30mmx30mmx1mm VIn -7.2mW/C PCB size (30mmx30mmx1mm) 25 VCont 50 100 (85C) 150C The package loss is limited at the temperature that the internal temperature sensor works (about 150C). Therefore, the package loss is assumed to be an internal limitation. There is no heat radiation characteristic of the package unit assumed because of its small size. Heat is carried away from the device by being mounted on the PCB. This value is directly effected by the material and the copper pattern etc. of the PCB. The losses are approximately 400mW. Enduring these losses becomes possible in a lot of applications operating at 25C. GND (Top View) PCB Material: Glass epoxy Size: 7mmx8mmx0.8mm Please do derating with 3.2mW/C(PCB size: 7mmx 8mmx0.8mm), 7.2mW/C(PCB size: 30mmx30mmx 1mm), at PD=400mW(PCB size: 7mmx8mmx0.8m), 900mW(PCB size: 30mmx30mmx1mm), and 25C or more. The overheating protection circuit operates when the junction temperature reaches 150C (this happens when the regulator is dissipating excessive power, outside temperature is high, or heat radiation is bad). The output current and the output voltage will drop when the protection circuit operates. However, operation begins again as soon as the output voltage drops and the temperature of the chip decreases. How to determine the thermal resistance when mounted on PCB The thermal resistance when mounted is expressed as follows: Tj=jaPD+Ta Tj of IC is set around 150C. PD is the value when the thermal sensor is activated. If the ambient temperature is 25C, then: 150=jaPD+25 ja=125/PD (C /mW) AP-MS0036-E-00 - 24 - 2011/02 [TK634xxAMF] PD is easily calculated. A simple way to determine PD is to calculate VInIIn when the output side is shorted. Input current gradually falls as output voltage rises after working thermal shutdown. You should use the value when thermal equilibrium is reached. Fig12-6: How to determine DPD PD (mW) 12-3-. On/Off Control It is recommended to turn the regulator Off when the circuit following the regulator is not operating. A design with little electric power loss can be implemented. We recommend the use of the On/Off control of the regulator without using a high side switch to provide an output from the regulator. A highly accurate output voltage with low voltage drop is obtained. Because the control current is small, it is possible to control it directly by CMOS logic. 2 PD Fig12-7: The use of On/Off control DPD Vsat 3 5 REG 4 On/Off Cont. 25 50 75 100 Ta (C) 125 150 Procedure (When mounted on PCB.) 1. Find PD (VInIIn when the output side is shortcircuited). 2. Plot PD against 25C. 3. Connect PD to the point corresponding to the 150C with a straight line. 4. In design, take a vertical line from the maximum operating temperature (e.g., 75C) to the derating curve. 5. Read off the value of PD against the point at which the vertical line intersects the derating curve. This is taken as the maximum power dissipation DPd. 6. DPD (VIn,MAXVOut)=IOut (at 75C) The maximum output current at the highest operating temperature will be IOut DPD (VIn,MAX-VOut). Please use the device at low temperature with better radiation. The lower temperature provides better quality. Control Terminal Voltage ((VCont) VCont > 1.2V VCont < 0.2V On/Off State On Off Parallel Connected On/Off Control Fig12-8: The example of parallel connected IC VIn VOut TK63442A 4.2V TK63428A 2.8V TK63415A 1.5V On/Off Cont. The above figure is multiple regulators being controlled by a single On/Off control signal. There is concern of overheating, because the power loss of the low voltage side IC (TK63415A) is large. The series resistor (R) is put in the input line of the low output voltage regulator in order to prevent over-dissipation. The voltage dropped across the resistor reduces the large input-to-output voltage across the regulator, reducing the power dissipation in the device. When the thermal sensor works, a decrease of the output voltage, oscillation, etc. may be observed. AP-MS0036-E-00 - 25 - 2011/02 [TK634xxAMF] 12-4-. Definition of term Characteristics Protections Output Voltage (VOut) The output voltage is specified with VIn=(VOutTYP+1V) and IOut=5mA. Maximum Output Current (IOut, MAX) The rated output current is specified under the condition where the output voltage drops to 90% of the value specified with IOut=5mA. The input voltage is set to VOutTYP+1V and the current is pulsed to minimize temperature effect. Dropout Voltage (VDrop) The dropout voltage is the difference between the input voltage and the output voltage at which point the regulator starts to fall out of regulation. Below this value, the output voltage will fall as the input voltage is reduced. It is dependent upon the output voltage, the load current, and the junction temperature. Line Regulation (LinReg) Line regulation is the ability of the regulator to maintain a constant output voltage as the input voltage changes. The line regulation is specified as the input voltage is changed from VIn=VOut,TYP+1V to VIn=6V. It is a pulse measurement to minimize temperature effect. Over Current Sensor The over current sensor protects the device when there is excessive output current. It also protects the device if the output is accidentally connected to ground. Thermal Sensor The thermal sensor protects the device in case the junction temperature exceeds the safe value (Tj=150C). This temperature rise can be caused by external heat, excessive power dissipation caused by large input to output voltage drops, or excessive output current. The regulator will shut off when the temperature exceeds the safe value. As the junction temperatures decrease, the regulator will begin to operate again. Under sustained fault conditions, the regulator output will oscillate as the device turns off then resets. Damage may occur to the device under extreme fault. Please prevent the loss of the regulator when this protection operates, by reducing the input voltage or providing better heat efficiency. ESD MM : 200pF 0 150V or more HBM : 100pF 1.5k 2000V or more Load Regulation (LoaReg) Load regulation is the ability of the regulator to maintain a constant output voltage as the load current changes. It is a pulsed measurement to minimize temperature effects with the input voltage set to VIn=VOut,TYP+1V. The load regulation is specified under an output current step condition of 1mA to 50mA. Ripple Rejection (RR) Ripple rejection is the ability of the regulator to attenuate the ripple content of the input voltage at the output. It is specified with 500mVP-P, 1kHz super-imposed on the input voltage, where VIn=VOut,TYP+1.5V. Ripple rejection is the ratio of the ripple content of the output vs. input and is expressed in dB. Standby Current (IStandby) Standby current is the current which flows into the regulator when the output is turned off by the control function (VCont=0V). AP-MS0036-E-00 - 26 - 2011/02 [TK634xxAMF] 13-. PACKAGE OUTLINE 4-Lead-Small Outline Non-Leaded Package with Heat Sink : HSON1214-4 0.25 3 1 Pin Mark 1 1.80 0.60 1.4+0.05 0.40 4 2 0.5 1.2+0.05 Reference Mount Pad 0.55+ 0.05 0.075 +0.05 0.15 +0.05 1.00 0.2 +0.05 0.13 + 0.03 0.5 (0.2) 0.1 + 0.05 0.6+ 0.05 4 (0.075) 2 0.2 + 0.05 1 3 0.9+0.05 Unit : mm Package Structure and Others Package Material Terminal Material Terminal Finish : Epoxy Resin : Copper Alloy : Ni/Pd/Au Caution in Printed Circuit Board Layout In addition to the normal pins, this plastic package has exposed metal tabs. This tab is electrically connected to the GND of internal chip. Avoid electrical contact with this tab from external print traces, adjacent components other than GND, etc. This tab is recommended to be solder-mounted so as to enhance heat release. AP-MS0036-E-00 - 27 - 2011/02 [TK634xxAMF] Marking Part Number TK63415AMF TK63418AMF TK63425AMF TK63426AMF TK63427AMF TK63428AMF AP-MS0036-E-00 Marking Code D15 D18 D25 D26 D27 D28 Part Number TK63401AMF TK63429AMF TK63430AMF TK63431AMF TK63432AMF TK63433AMF - 28 - Marking Code D01 D29 D30 D31 D32 D33 Part Number TK63435AMF TK63440AMF Marking Code D35 D40 2011/02 [TK634xxAMF] IMPORTANT NOTICE These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKM products are neither intended nor authorized for use as critical components Note1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. AP-MS0036-E-00 - 29 - 2011/02