RH117 Positive Adjustable Regulator W W U W U DESCRIPTIO ABSOLUTE The RH117 is a 3-terminal positive adjustable regulator capable of supplying up to 0.5A (H package) or 1.5A (K package). The output is adjusted using two external resistors for a range of 1.2V to 37V. The devices have full current limit thermal overload safe area protection, all of which remain functional even if the adjustment terminal is disconnected. Power Dissipation ............................... Internally Limited Input-to-Output Voltage Differential ......................... 40V Operating Junction Temperature Range ......................... - 55C to 150C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C RATI GS , LTC and LT are registered trademarks of Linear Technology Corporation. W U U U BUR -I CIRCUIT U The wafer lots are processed to LTC's in-house Class S flow to yield circuits usable in stringent military applications. In addition to 883 processing, the RH117 is subjected to 100% burn-in in thermal limit. AXI U PACKAGE/ORDER I FOR ATIO BOTTOM VIEW RH117 20V ADJ OUTPUT VIN 2 ADJ OUTPUT INPUT 3 1 2k -20V 61.9W H PACKAGE 3-LEAD TO-39 METAL CAN RH117 BI BOTTOM VIEW VIN 2 CASE IS OUTPUT 1 ADJ K PACKAGE 2-LEAD TO-3 METAL CAN 1 RH117 TABLE 1: ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER CONDITIONS VREF Reference Voltage 3V (VIN - VOUT) 40V, 10mA IOUT IMAX, P PMAX DVOUT DVIN Line Regulation 3V (VIN - VOUT) 40V, IOUT = 10mA DVOUT DIOUT Load Regulation 10mA IOUT IMAX, VOUT 5V 10mA IOUT IMAX, VOUT 5V Thermal Regulation 20ms Pulse Ripple Rejection MIN TJ = 25C TYP MAX 1.20 1.30 1 2 0.02 2 2 NOTES VOUT = 10V, f = 120Hz, CADJ = 0 VOUT = 10V, f = 120Hz, CADJ = 10mF 1.20 1.30 2,3 V 1 0.05 2,3 %/V 15 0.3 1 1 50 1 2,3 2,3 mV % 0.07 1 %/W 65 3 UNITS 65 66 dB 66 dB 100 1 100 2,3 mA 5 1 5 2,3 mA 2.5V (VIN - VOUT) 40V, IOUT = 10mA 5 1 5 2,3 mA Minimum Load Current (VIN - VOUT) = 40V 5 1 5 2,3 mA Current Limit (VIN - VOUT) 15V H Package K Package 0.5 1.5 1 1 2,3 2,3 A A (VIN - VOUT) = 40V H Package K Package 0.15 0.30 1 1 Adjust Pin Current DIADJ Adjust Pin Current Change DVOUT DTemp Temperature Stability - 55C TJ 150C DVOUT DTime Long Term Stability en RMS Output Noise 10Hz f 10kHz qJC Thermal Resistance (Junction to Case) H Package K Package TA = 125C 0.5 1.5 A A 1 3 % 1 % 0.001 3 3 % C/W C/W 15 3 TABLE 1A: ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER CONDITIONS VREF Reference Voltage 3V (VIN - VOUT) 40V, 10mA IOUT IMAX, P PMAX DVOUT DVIN Line Regulation 3V (VIN - VOUT) 40V, IOUT = 10mA 2 DVOUT DIOUT Load Regulation 10mA IOUT IMAX, VOUT 5V 10mA IOUT IMAX, VOUT 5V 2 2 2 SUB- - 55C TJ 150C SUBGROUP MIN TYP MAX GROUP 10mA IOUT IMAX IADJ IMIN (Preirradiation) (Note 1) NOTES (Postirradiation) (Note 4) 10KRAD(Si) MIN MAX 20KRAD(Si) MIN MAX 1.20 1.20 1.30 50KRAD(Si) MIN MAX 1.30 1.20 1.30 0.02 0.02 36 0.72 42 0.84 100KRAD(Si) MIN MAX 1.20 UNITS 1.30 V 0.02 0.03 %/V 48 0.96 60 1.20 mV % RH117 TABLE 1A: ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER IADJ Adjust Pin Current DIADJ Adjust Pin Current Change IMIN CONDITIONS NOTES (Postirradiation) (Note 5) 10KRAD(Si) MIN MAX 20KRAD(Si) MIN MAX 50KRAD(Si) MIN MAX 100KRAD(Si) MIN MAX UNITS 100 100 100 100 mA 10mA IOUT IMAX 5 5 5 5 mA 3V (VIN - VOUT ) 40V, IOUT = 10mA 5 5 5 5 mA Minimum Load Current (VIN - VOUT ) = 40V 5 5 5 5 mA Current Limit (VIN - VOUT ) 15V H Package K Package 0.5 1.5 0.5 1.5 0.5 1.5 0.5 1.5 A A (VIN - VOUT ) = 40V H Package K Package 0.15 0.30 0.15 0.30 0.15 0.30 0.15 0.30 A A Note 2: Regulation is measured at a constant junction temperature using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are covered under the specification for thermal regulation. Note 3: Guaranteed by design, characterization or correlation to other tested parameters. Note 4: TJ = 25C unless otherwise noted. Note 1: Unless otherwise specified, these specifications apply for VIN - VOUT = 5V; and IOUT = 0.1A for the H package (TO-39) and IOUT = 0.5A for the K package (TO-3) package. Although power dissipation is internally limited, these specifications are applicable for power dissipations of 2W for the TO-39 and 20W for the TO-3. IMAX is 0.5A for the TO-39 and 1.5A for the TO-3. TOTAL DOSE BIAS CIRCUIT RH117 15V OUTPUT VIN ADJ 0.1mF 2k -15V 61.9W RH117 TA01 U W TABLE 2: ELECTRICAL TEST REQUIRE E TS MIL-STD-883 TEST REQUIREMENTS SUBGROUP Final Electrical Test Requirements (Method 5004) 1*,2,3 Group A Test Requirements (Method 5005) 1,2,3 Group C and D End Point Electrical Parameters (Method 5005) * PDA Applies to subgroup 1. See PDA Test Notes. 1 PDA Test Notes The PDA is specified as 5% based on failures from group A, subgroup 1, tests after cooldown as the final electrical test in accordance with method 5004 of MIL-STD-883 Class B. The verified failures of group A, subgroup 1, after burn-in divided by the total number of devices submitted for burnin in that lot shall be used to determine the percent for the lot. Linear Technology Corporation reserves the right to test to tighter limits than those given. Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 3 RH117 U W TYPICAL PERFORMANCE CHARACTERISTICS Reference Voltage Regulation 1.28 1.26 1.24 1.22 1 10 100 TOTAL DOSE KRAD (Si) (VIN - VOUT) = 13V 15 10 5 LOAD 1.5 1.0 0.5 LINE 0 1000 MINIMUM LOAD CURRENT (mA) DIFFERENTIAL REFERENCE VOLTAGE (mV) REFERENCE VOLTAGE (V) 3V (VIN - VOUT) 40V 10mA IOUT IMAX 1.20 Minimum Load Current 2.0 20 0 10 100 TOTAL DOSE KRAD (Si) 1 RH117 G01 1000 1 10 100 TOTAL DOSE KRAD (Si) RH117 G03 RH117 G02 Adjust Pin Current Adjust Pin Current Change 55 1000 Current Limit 3.5 2.0 ADJUST CURRENT (mA) 45 40 35 30 25 20 1 10 100 TOTAL DOSE KRAD (Si) 1000 3.0 (VIN - VOUT) = 4.25V 1.5 CURRENT LIMIT (A) ADJUST PIN CURRENTCHANGE (mA) (VIN - VOUT) = 3V 50 1.0 2.5V (VIN - VOUT) 40V 0.5 10mA IOUT IMAX 2.5 2.0 1.5 (VIN - VOUT) = 40V 1.0 0.5 0 0 1 RH117 G04 10 100 TOTAL DOSE KRAD (Si) 1000 RH117 G05 1 10 100 TOTAL DOSE KRAD (Si) 1000 RH117 G06 I.D. No. 66-11-0135 Rev. C 0796 4 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 FAX: (408) 434-0507 www.linear-tech.com LT 0401 REV C * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1989