Disc Ceramic Capacitors General Specifications - Class I Temperature Compensating DIELECTRIC - CLASS I These ceramic capacitors have linear temperature coefficient, very low tolerances, low losses, high insulation resistance and are specially suitable for tuned circuits, timing and other precision circuits. Meets IEC 384-8 (1988). DIMENSIONS Digit 9 D 2 (o) (0.079) A B C D E F G H J K M 4.0 (0.157) 5.0 (0.197) 6.0 (0.236) 7.0 (0.276) 8.0 (0.315) 9.0 (0.354) 10.0 (0.394) 11.0 (0.433) 13.0 (0.512) 15.0 (0.591) 19.0 (0.748) 100V - 500V (E), (X), (W): upon request 6 millimeters (inches) T max. 3.0 (0.118) 4.0 (0.157) 4.0 (0.157) 4.0 (0.157) 4.0 (0.157) 5.0 (0.197) 5.0 (0.197) 5.0 (0.197) 6.0 (0.236) 6.0 (0.236) 7.0 (0.276) O = 0.6 0.1 (0.024) (0.004) Available Lead Spacing 1000V 2000V 3000V 4000/5000V Preferred lead spacing F = 5 (0.197) A,B,D,E,O,R A,B,E,N,R A,B,E,N,R B,E A,B,D,E,O,R,X A,B,E,N,R,X A,B,E,N,R B,E A,B,C,E,N,R, B,C,E C A,B,C,D,E,O,R,X A,B,C,E,N,Q,R,X A,B,C,E,N,Q,R B,C,E C A,B,C,D,E,O,R,X A,B,C,E,N,Q,R,X A,B,C,E,N,Q,R B,C,E C A,B,C,E,O,R,X A,B,C,E,N,R,X A,B,C,E,N,R, B,C,E C A,B,C,E,O,R,X A,B,C,E,N,R,X A,B,C,E,N,R, B,C,E C A,B,C,E,O,R,W A,B,C,E,N,P,R,W A,B,C,E,N,P,R,W B,C,E,P,W C,P B,C,R,W B,C,N,P,R,W B,C,N,P,R,W B,C,P,W C,P B,C,R,W B,C,N,P,R,W B,C,N,P,R,W B,C,P,W C,P B,C B,C,P B,C,P B,C,P C,P A,B,C,D,E,O,R,X A,B,C,E,N,R,X millimeters (inches) Lead Spacing Digit 8 of P.N. F 2.5 (0.100) 5 (0.200) 6 (0.250) 7.5 (0.300) 10 (0.400) 12.5 (0.500) D A E B C P -- O X R W -- N -- Q -- -- Disc Ceramic Capacitors General Specifications - Class I Temperature Compensating PERFORMANCE CHARACTERISTICS Measured at Dissipation Factor (%) Tolerance Insulation (IR) Resistance Dielectric Strength NOTE: Charging current limited to 50 mA Operating Temperature Range (C) Climatic Category 100 V 500 V 1.0 MHz @ 1.0 Vrms & 25C CR 30 pF 1/CR + 0.07 CR > 30 pF 0.1% CR < 10 pF 0.25 pF, 0.5 pF CR 10 pF 5%, 10% 1kV 5kV 1.0 MHz @ 1.0 Vrms & 25C CR 30 pF 1/CR + 0.07 CR > 30 pF 0.1% CR < 10 pF 0.25 pF, 0.5 pF CR 10 pF 5%, 10% @ VR 10 G @ 500V 10 G @ VR = 100V Vt = 250V (DC) @ VR = 500V Vt = 1.25kV (DC) 1.5 x VR + 500 (DC) -30 +85 -30 +85 Phenolic Coated -30 +125 Epoxy Coated 30 / 085 / 21 Phenolic Coated 30 / 085 / 21 Phenolic Coated 30 / 085 / 56 Epoxy Coated Note: Damp Heat Steady State: 90... 95% R.H. 40C / 21 days. No voltage to be applied. 7 Disc Ceramic Capacitors Dimension Table - Class I Temperature Compensating CLASS I - CAPACITANCE VS. DISC DIAMETER Temp. Coefficient Digits 1, 2, 3 of P.N. Rated Voltage (VR) CR (pF) 1.0 1.2 1.5 1.8 2.0 2.2 2.7 3.0 3.3 3.9 4.0 4.7 5.0 5.6 6.0 6.8 7.0 8.0 8.2 9.0 10 12 15 18 20 22 27 33 39 47 50 56 68 82 100 120 150 180 220 270 330 8 millimeters (inches) NP0 5AK 5AQ 5AR 5AS 5AT 5AU 100 VDC 500 VDC 1000 VDC 130 VAC 2000 VDC 250 VAC 3000 VDC 380 VAC 4000 VDC 440 VAC 4.0 (0.157) 4.0 (0.157) 4.0 (0.157) 4.0 (0.157) 6.0 (0.236) 6.0 (0.236) 5.0 (0.197) 5.0 (0.197) 6.0 (0.236) 5.0 (0.197) 8.0 (0.315) 7.0 (0.276) 8.0 (0.315) 8.0 (0.315) 9.0 (0.354) 9.0 (0.354) 11.0 (0.433) 11.0 (0.433) 15.0 (0.591) 19.0 (0.748) 8.0 (0.315) 8.0 (0.315) 10.0 (0.394) 7.0 (0.276) 6.0 (0.236) 7.0 (0.276) 8.0 (0.315) 6.0 (0.236) 5.0 (0.197) 7.0 (0.276) 7.0 (0.276) 9.0 (0.354) 9.0 (0.354) 11.0 (0.433) 11.0 (0.433) 13.0 (0.512) 13.0 (0.512) 15.0 (0.591) 19.0 (0.748) 13.0 (0.512) 15.0 (0.591) 9.0 (0.354) 11.0 (0.433) 11.0 (0.433) 13.0 (0.512) 15.0 (0.591) 15.0 (0.591) 19.0 (0.748) Disc Ceramic Capacitors Dimension Table - Class I Temperature Compensating CLASS I - CAPACITANCE VS. DISC DIAMETER Temp. Coefficient Digits 1, 2, 3 of P.N. Rated Voltage (VR) CR (pF) 1.0 1.2 1.5 1.8 2.0 2.2 2.7 3.0 3.3 3.9 4.0 4.7 5.0 5.6 6.0 6.8 7.0 8.0 8.2 9.0 10 12 15 18 20 22 27 33 39 47 50 56 68 82 100 120 150 180 220 270 330 millimeters (inches) N750 5GK N1500 5GQ 5GR 5GS 5GT 5GU 5GW 5HK 5HQ 100 VDC 500 VDC 1000 VDC 130 VAC 2000 VDC 250 VAC 3000 VDC 380 VAC 4000 VDC 440 VAC 5000 VDC 550 VAC 100 VDC 500 VDC Use NP0 Use NP0 Use NP0 4.0 (0.157) 4.0 (0.157) Use NP0 Use NP0 4.0 (0.157) 4.0 (0.157) 5.0 (0.197) 5.0 (0.197) 6.0 (0.236) 8.0 (0.315) 6.0 (0.236) 5.0 (0.197) 5.0 (0.197) 7.0 (0.276) 8.0 (0.315) 9.0 (0.354) 11.0 (0.433) 7.0 (0.276) 7.0 (0.276) 8.0 (0.315) 8.0 (0.315) 7.0 (0.276) 8.0 (0.315) 11.0 (0.433) 11.0 (0.433) 5.0 (0.197) 6.0 (0.236) 6.0 (0.236) 6.0 (0.236) 7.0 (0.276) 9.0 (0.354) 8.0 (0.315) 9.0 (0.354) 11.0 (0.433) 11.0 (0.433) 13.0 (0.512) 13.0 (0.512) 15.0 (0.591) 15.0 (0.591) 9.0 (0.354) 9.0 (0.354) 11.0 (0.433) 15.0 (0.591) 11.0 (0.433) 13.0 (0.512) 19.0 (0.748) 19.0 (0.748) 5.0 (0.197) 7.0 (0.276) 13.0 (0.512) 15.0 (0.591) 15.0 (0.591) 6.0 (0.236) 7.0 (0.276) 8.0 (0.315) 9.0 (0.354) 8.0 (0.315) 9.0 (0.354) 11.0 (0.433) 9 Disc Ceramic Capacitors Ordering Code HOW TO ORDER 5 O Q 222 General Purpose 5A = NP0 / I *5B = P100 / I *5C = N150 / I *5D = N220 / I *5E = N330 / I *5F = N470 / I 5G = N750 / I 5H = N1500 / I *5I = N2200 / I *5J = N4700 / I 5K = SL 5M = Y5E / II 5N = Y5F / II 5O = Y5P / II *5P = Y5R / II *5Q = Y5T / II 5S = Y5U / II 5T = Y5V / II 5U = Z5V / II *5V = Z4V / III 5W = Y5P / III 5Y = Y5U / III 5Z = Y5V / III Professional Switch Mode Safety 6A = NP0 / I *6B = P100 / I *6C = N150 / I *6D = N220 / I *6E = N330 / I *6F = N470 / I 6G = N750 / I *6H = N1500 / I *6I = N2200 / I 6J = N4700 / I 61 = SAFETY 62 = SAFETY 65 = SAFETY 67 = Y5U / SM 68 = Y5V / SM 6L = Y5P / SM 6M = X5E / II 6N = X5F / II 6O = X5P / II *6P = X5R / II *6Q = X5T / II 6S = X5U / II 6T = X5V / II 6U = Z5V / II *6V = Z4V / III 6W = Y5P / III 6Y = Y5U / III 6Z = Y5V / III Rated Voltage (dc) D = 16V F = 25V H = 50V K = 100V N = SAFETY O = SAFETY Q = 500V R = 1000V S = 2000V T = 3000V U = 4000V V = SAFETY W = 5000V *X = 6000V *Y = 7500V Capacitance 222 = 2.2 nF *Upon Request 4 Capacitance = TPC code 1 pF = 1R0 1.2pF = 1R2 1.5pF = 1R5 1.8pF = 1R8 2.2pF = 2R2 2.7pF = 2R7 3.9pF = 3R9 4.7pF = 4R7 5.6pF = 5R6 6.8pF = 6R8 8.2pF = 8R2 10pF = 100 12pF = 120 15pF = 150 18pF = 180 22pF = 220 27pF = 270 33pF = 330 39pF = 390 47pF = 470 56pF = 560 68pF = 680 82pF = 820 Capacitance = TPC code 100pF = 101 120pF = 121 150pF = 151 180pF = 181 220pF = 221 270pF = 271 330pF = 331 390pF = 391 470pF = 471 560pF = 561 680pF = 681 820pF = 821 1nF = 102 1.2nF = 122 1.8nF = 182 2.2nF = 222 2.7nF = 272 3.3nF = 332 3.9nF = 392 4.7nF = 472 5.6nF = 562 6.8nF = 682 8.2nF = 822 10nF = 103 15nF = 153 22nF = 223 33nF = 333 47nF = 473 100nF = 104 200nF = 204 Disc Ceramic Capacitors Ordering Code M A E Tolerance C = 0.25 pF D = 0.50 pF J = 5% K = 10% M = 20% S = -20+50% Z = -20+80% P = 0+100% A A Packaging Capacitor Diameter 2 (0.079) A = 4 (0.157) B = 5 (0.197) C = 6 (0.236) D = 7 (0.276) E = 8 (0.315) F = 9 (0.354) G = 10 (0.394) H = 11 (0.433) J = 13 (0.512) K = 15 (0.591) M* = 19 (0.748) Cardboard Strips A= Bulk E = 5 (0.197) 1 (0.039) free wire length C = 10 (0.394) 1 (0.039) free wire length D = 25 (0.984) 1 (0.039) free wire length Taping Avisert Reel Panasert *Wire 0.8 (0.031) recommended H Lead Forming inches 2.5 0.5 +0.6 5 -0.2 +0.6 6 -0.2 +1 7.5 -0.5 +0.5 10 -1.0 +1 12.5 -0.5 .1 .025 D - - .2 .025 A O N .25 .025 E X - .3 .05 B R Q .4 .05 C W - .5 .05 P - - L Avisert Ammo Pack mm L I M M J L L Panasert K M M Finishing Diam 9 (0.354) and F = 5.00 (0.197) For every other: Coating does not surpass the bend Low Voltage A = Phenolic General Q = Waxed phenolic ( Purpose ) S = Epoxy (Professional) cap. diameter 8 (0.315) D = Epoxy (Professional) cap. diameter > 8 (0.315) High Voltage F = Measured from the center of leads 0.6 0.1 (0.024) (0.004) 0.8 0.1 I = Epoxy wire diameter (0.031) (0.004) L = Phenolic wire diameter 0.6 0.1 (0.024) (0.004) C = Epoxy wire diameter Please note that not all code combinations are either possible or available. 5 Disc Ceramic Capacitors Packaging IDENTIFICATION AND TRACEABILITY On all TPC ceramic capacitors packages, you will find a bar code label with the following information: Lot number Manufacturing date Quantity of parts per packaging Product part number TAPED PARTS QUANTITY TABLE millimeters (inches) Rated Voltage (Vr) Diameter D Quantities Ammopack Vr <= 500V D 7 (0.276) 2000 2500 7 < D 11 (0.433) 2000 2000 500V<Vr<=2KV D 11 (0.433) 1500 2000 2KV<Vr=5KV D 11 (0.433) 1000 1500 Reel CARDBOARD STRIPS QUANTITY TABLE Rated Voltage (Vr) Vr <= 500V 500V<Vr<=2KV 2KV<Vr<=5KV millimeters (inches) Diameter D < = 5 (0.197) Lead Space > 5 (0.197) D 8 (0.315) 2500 1500 8 (0.315) D 11 (0.433) 1500 - 8 (0.315) D 13 (0.512) - 1000 11 (0.433) D 15 (0.591) 1000 - 13 (0.512) D 19 (0.748) - 500 D 19 (0.748) 500 - D 9 (0.354) 1500 1000 9 (0.354) D 11 (0.433) - 1000 9 (0.354) D 13 (0.512) 1000 - 11 (0.433) D 19 (0.748) - 500 13 (0.512) D 19 (0.748) 500 - D 9 (0.354) 1500 - D 11 (0.433) - 1000 D 13 (0.512) 500 500 Safety D 6 (0.236) 1500 1500 61V 7 (0.275) D 9 (0.354) 1000 1000 9 (0.354) D 500 500 Safety 65N 62O Quantities for other package alternative, upon request. 29 Disc Ceramic Capacitors Tape and Reel Specifications There are two types of taped disc ceramic capacitors: Straight or crimped leads. Both types can be shipped on reels or ammopack. The standard packaging quantities are shown bellow: millimeters (inches) Fig. 1 Fig. 2 Fig. 3 Straight leads Crimped leads Maximum pull force during insertion and lead cut F1 Digit 11 L M J H K I TPC Code 4 (0.157) D < 6 (0.236) 12N 20N D 6 (0.236) 20N 25N Available Tapings Digit 9 Sizes 4 (0.157) D 11 (0.433) A... H Sizes 6 (0.236) D 11 (0.433) C... H Digit 11 Packaging Avisert Panasert H L L FIGURE 1 FIGURE 2 FIGURE 3 J L L FIGURE 1 FIGURE 2 FIGURE 3 I M M FIGURE 1 FIGURE 2 FIGURE 3 K M M FIGURE 1 FIGURE 2 FIGURE 3 Reel Ammopack Figure 2: Inside Crimp 100V... 1000V Figure 3: Outside Crimp 1000V 30 F2 Disc Ceramic Capacitors Tape and Reel Specifications millimeters (inches) Straight Leads Figure 1 A (Avisert) P (Panasert) Description of Symbols Crimped Figure 2 & 3 Avisert & Panasert Crimp angle -- -- 20...45 Crimp length C -- -- 1.7 min. Lead diameter d 0.60 0.1 Disc diameter D 11 max. Lead hole diameter Do 4.0 0.2 Disc thickness T See Catalog Lead spacing F 5.0 +0.6 -0.2 h Component alignment, front-rear 01 Height of component from tape center H 19.5 0.5 16.5 0.5 - 0 -- Height from tape center to crimp Ho -- 16 + 0.5 - 0 Component height H1 32.25 max. Distance from component leads to tape bottom 1 -- >23.5 <32.25 12 max. Tape width W 18 Bonding tape width W3 5.5 min. Feed hole position W1 9.0 0.5 Pitch between discs P 12.7 1 Feed hole pitch Po 12.7 0.3 Hole center to lead P1 3.85 0.7 Feed hole center to component center P2 6.35 1 Tape + bonding tape thickness t 0.7 0.2 Total tape thickness. including lead t2 1.5 max. +1 -0.5 SHIPPING CONTAINER PACKAGING Ammopack 32.25 max. Reel 8 Ammopack 5 Reel This side up during storage and transportation max. stacking: 10 boxes max. stacking: 10 reels 31 Disc Ceramic Capacitors Marking DIG. 2 Logo: Only in diam. 6mm O TC / Class General Purpose A = NP0 / I *B = P100 / I *C = N150 / I *D = N220 / I *E = N330 / I *F = N470 / I G = N750 / I H = N1500 / I *I = N2200 / I *J = N4700 / I K = SL M = Y5E / II N = Y5F / II O = Y5P / II P = Y5R / II Q = Y5T / II S = Y5U / II T = Y5V / II U = Z5V / II V = Z4V / III *W = Y5P / II *X = Y5R / II Y = Y5U / II Z = Y5V / II *Upon Request Professional A = NP0 / I B = P100 / I C = N150 / I D = N220 / I E = N330 / I F = N470 / I G = N750 / I H = N1500 / I I = N2200 / I J = N4700 / I 7 = Y5U / SM 8 = Y5V / SM L = Y5P / SM M = X5E / II N = X5F / II O = X5P / II P = X5R / II Q = X5T / II S = X5U / II T = X5V / II U = Z5V / II V = Z4V / III W = Y5P / III X = Y5R / III Y = Y5U / III Z = Y5V / III 222 OQM DIG. 3 Q DIG. 7 M Rated Voltage D = 16V F = 25V H = 50V K = 100V Q = 500V R = 1000V S = 2000V T = 3000V U = 4000V W = 5000V X = 6000V Y = 7500V Tolerance C = 0.25pF D = 0.5pF J = 5% K = 10% M = 20% S = -20 +50% Z = -20 +80% P = 0 +100% Capacitance 1pF = 109 1.2pF = 129 1.5pF = 159 1.8pF = 189 2.2pF = 229 2.7pF = 279 3.9pF = 399 4.7pF = 479 5.6pF = 569 6.8pF = 689 8.2pF = 829 10pF = 100 12pF = 120 15pF = 150 18pF = 180 22pF = 220 27pF = 270 39pF = 390 47pF = 470 56pF = 560 68pF = 680 82pF = 820 Safety Front Capacitance As above EIA 100pF = 101 120pF = 121 150pF = 151 180pF = 181 220pF = 221 270pF = 271 390pF = 391 470pF = 471 560pF = 561 680pF = 681 820pF = 821 1nF = 102 1.2nF = 122 1.8nF = 182 2.2nF = 222 2.7nF = 272 3.9nF = 392 4.7nF = 472 5.6nF = 562 6.8nF = 682 8.2nF = 822 10nF = 103 15nF = 153 22nF = 223 33nF = 333 47nF = 473 100nF = 104 200nF = 204 Type 61V 61V 471M TC - Temperature coefficient. DIG - for better understanding, check pages 3 and 4. 620 65N Tolerance As above Back: (Approval marks) 28