TVS Diodes Axial Leaded - 30000W > 30KPA series 30KPA Series RoHS Pb e3 Descriptios Uni-directional The 30KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional * V BR @TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient) * Glass passivated chip junction in P600 package * 30000W peak pulse capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0 Volts to BV min * Excellent clamping capability * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 30000 W Steady State Power Dissipation on Inifinite Heat Sink at TL=75C (Fig. 5) PD 8.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A TJ , TSTG -55 to 175 C Typical Thermal Resistance Junction to Lead RuJL 8.0 C/W Typical Thermal Resistance Junction to Ambient RuJA 40 C/W Peak Pulse Power Dissipation by 10/1000s Test Waveform (Fig.2) (Note 1) Operating Junction and Storage Temperature Range * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Low incremental surge resistance * Typical IR less than 2A above 73V * High temperature soldering guaranteed: 260C/40 seconds / 0.375",(9.5mm) lead length, 5 lbs., (2.3kg) tension * Plastic package has underwriters laboratory flammability classification 94V-O * Matte tin lead-free plated * Halogen free and RoHS compliant * 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. Functional Diagram Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Bi-directional Cathode Anode Uni-directional 30KPA Series 154 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded - 30000W > 30KPA series Electrical Characteristics (T =25C unless otherwise noted) A MAX Test Current IT (mA) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @VR ( A) Maximum Clamping Voltage VC @ IPP (V) 34.41 36.86 40.59 44.22 47.96 51.59 52.80 55.33 58.96 62.70 66.33 71.28 73.70 78.65 81.07 86.02 87.23 88.44 92.18 50 50 50 50 20 10 10 5 5 5 5 5 5 5 5 5 5 5 5 606.0 548.9 517.9 490.3 450.9 420.8 415.1 391.5 371.3 350.7 331.5 327.9 297.1 291.3 283.2 278.0 271.7 265.8 253.8 5000 5000 5000 5000 2000 1000 1000 250 150 50 20 20 15 10 2 2 2 2 2 50.0 55.2 58.5 61.8 67.2 72.0 73.0 77.4 81.6 86.4 91.4 92.4 102.0 104.0 107.0 109.0 111.5 114.0 119.4 87.10 93.80 100.50 107.20 113.90 120.60 134.00 147.40 160.80 167.60 174.30 178.70 187.70 189.90 201.10 95.81 103.18 110.55 117.92 125.29 132.66 147.40 162.14 176.88 184.36 191.73 196.57 206.47 208.89 221.21 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 234.9 217.7 207.0 194.2 183.0 172.9 155.9 142.3 135.8 129.8 123.7 120.0 111.2 110.2 104.3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 129.0 139.2 146.4 156.0 165.6 175.2 194.4 213.0 223.2 233.4 245.0 252.6 272.4 275.0 290.4 221.20 241.30 268.10 288.20 290.40 301.60 312.80 321.70 334.00 243.32 265.43 294.91 317.02 319.44 331.76 344.08 353.87 367.40 5 5 5 5 5 5 5 5 5 94.7 86.9 78.3 72.8 72.8 69.5 65.3 64.5 62.0 2 2 2 2 2 2 2 2 2 319.8 348.6 387.0 416.4 416.0 436.2 464.0 469.9 484.0 Breakdown Voltage VBR (Volts) @ IT Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) MIN 30KPA28A 30KPA30A 30KPA33A 30KPA36A 30KPA39A 30KPA42A 30KPA43A 30KPA45A 30KPA48A 30KPA51A 30KPA54A 30KPA58A 30KPA60A 30KPA64A 30KPA66A 30KPA70A 30KPA71A 30KPA72A 30KPA75A 30KPA78A 30KPA84A 30KPA90A 30KPA96A 30KPA102A 30KPA108A 30KPA120A 30KPA132A 30KPA144A 30KPA150A 30KPA156A 30KPA160A 30KPA168A 30KPA170A 30KPA180A 30KPA198A 30KPA216A 30KPA240A 30KPA258A 30KPA260A 30KPA270A 30KPA280A 30KPA288A 30KPA300A 30KPA28CA 30KPA30CA 30KPA33CA 30KPA36CA 30KPA39CA 30KPA42CA 30KPA43CA 30KPA45CA 30KPA48CA 30KPA51CA 30KPA54CA 30KPA58CA 30KPA60CA 30KPA64CA 30KPA66CA 30KPA70CA 30KPA71CA 30KPA72CA 30KPA75CA 28 30 33 36 39 42 43 45 48 51 54 58 60 64 66 70 71 72 75 31.28 33.51 36.90 40.20 43.60 46.90 48.00 50.30 53.60 57.00 60.30 64.80 67.00 71.50 73.70 78.20 79.30 80.40 83.80 30KPA78CA 30KPA84CA 30KPA90CA 30KPA96CA 30KPA102CA 30KPA108CA 30KPA120CA 30KPA132CA 30KPA144CA 30KPA150CA 30KPA156CA 30KPA160CA 30KPA168CA 30KPA170CA 30KPA180CA 78 84 90 96 102 108 120 132 144 150 156 160 168 170 180 30KPA198CA 30KPA216CA 30KPA240CA 30KPA258CA 30KPA260CA 30KPA270CA 30KPA280CA 30KPA288CA 30KPA300CA 198 216 240 258 260 270 280 288 300 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VRWM of 60 volts and less, the IR limit is double. For parts without A , the VBR is + 10% and Vc is 5% higher than with A parts. 30KPA Series 155 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded - 30000W > 30KPA series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve 1000 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 100 10 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. 30KPA Series 156 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded - 30000W > 30KPA series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 175 tr=10sec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 10/1000sec. Waveform as defined by R.E.A td 0 200 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 1.0 0 TA-Ambient temperature (C) 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Derating Curve 9 10000 Steady State Power Dissipation (W) Cj, Junction Capacitance (pf) Bi-directional V= OV Uni-directional V= OV Uni-directional @ VR 100 Bi-directional @ VR Tj=25C f=1.0MHz Vsig=50mVp-p 1 0 50 100 150 200 250 VBR - Reverse Breakdown Voltage (V) 8 7 6 5 4 3 1 0 300 L = 0.375" (9.5mm) Lead Lengths 2 0 25 50 75 100 125 150 175 200 TL- Lead Temperature (C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current IFSM, Peak Forward Surge Current (A) 450 400 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz 30KPA Series 157 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded - 30000W > 30KPA series Soldering Parameters Pre Heat Lead-free assembly Ramp-up - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs TL Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow tp TP Temperature (T) Reflow Condition tL Ts(max) Ramp-down Ts(min) ts Preheat 25C - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Critical Zone TL to TP t 25C to Peak Time (t) Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6C/second max Peak Temperature : 265OC Time 25C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 280C Soldering : 1 time Environmental Specifications Physical Specifications Weight 0.07oz., 2.5g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 Dimensions D Cathode Band (for Uni-directional products only) Dimensions C A B A P600 30KPA Series 158 Inches Millimeters Min Max Min Max A 1.000 - 25.40 9.10 B 0.340 0.360 8.60 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 TVS Diodes Axial Leaded - 30000W > 30KPA series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band (for Uni-directional products only) TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) F 30KPA xxx XX X YYWW Trace Code Marking Littelfuse Logo VR VOLTAGE YY:Year Code WW: Week Code 30KPAXXX SERIES CODE Product Type Packing Options Part Number Component Package Quantity Packaging Option 30KPAxxxXX P600 800 Tape & Reel EIA STD RS-296 30KPAxxxXX-B P600 100 Bulk Littelfuse Spec. Packaging Specification Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) 30KPA Series Direction of Feed 159 (c)2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/09/14 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: 30KPA102A-B 30KPA108C-B 30KPA120-B 30KPA120A-B 30KPA132C-B 30KPA144-B 30KPA144C-B 30KPA150A-B 30KPA150C-B 30KPA156C-B 30KPA160A-B 30KPA170CA-B 30KPA180-B 30KPA198-B 30KPA216-B 30KPA216A-B 30KPA240-B 30KPA240C-B 30KPA240CA-B 30KPA258A-B 30KPA260-B 30KPA260C-B 30KPA260CA-B 30KPA270A-B 30KPA28-B 30KPA280C-B 30KPA280CA-B 30KPA288C-B 30KPA30C-B 30KPA30CA-B 30KPA33-B 30KPA33A-B 30KPA36C-B 30KPA42C-B 30KPA43A-B 30KPA43CA-B 30KPA45-B 30KPA45A-B 30KPA48-B 30KPA48A-B 30KPA48CA-B 30KPA54A-B 30KPA54C-B 30KPA54CA-B 30KPA58-B 30KPA58A-B 30KPA58CA-B 30KPA60C-B 30KPA60CA-B 30KPA66CA-B 30KPA70-B 30KPA70CA-B 30KPA71-B 30KPA71C-B 30KPA72CA-B 30KPA75A-B 30KPA75CA-B 30KPA78-B 30KPA78C-B 30KPA84-B 30KPA84C-B 30KPA90A-B 30KPA96C-B 30KPA60A-B 30KPA64A-B 30KPA84CA-B 30KPA198A-B 30KPA28CA-B 30KPA108-B 30KPA71A-B 30KPA120C-B 30KPA72A-B 30KPA42-B 30KPA102C-B 30KPA150-B 30KPA260A-B 30KPA30-B 30KPA90C-B 30KPA28C-B 30KPA168C-B 30KPA270C-B 30KPA66-B 30KPA51A-B 30KPA216C-B 30KPA75-B 30KPA42CA-B 30KPA120CA-B 30KPA156A-B 30KPA168A-B 30KPA288-B 30KPA156CA-B 30KPA48C-B 30KPA36A-B 30KPA54-B 30KPA30A-B 30KPA66A-B 30KPA180A-B 30KPA96CA-B 30KPA288A-B 30KPA51C-B