General Description
The MAX5456/MAX5457 dual, logarithmic taper digital
potentiometers feature a simple pushbutton interface
that controls volume and balance in audio applications.
Each potentiometer has 32 tap points and replaces
mechanical potentiometers. Refer to the MAX5408–
MAX5411 data sheet for SPI versions of the MAX5456/
MAX5457.
Use the MAX5456/MAX5457 digital inputs with momen-
tary contact single-pole/single-throw (SPST) pushbutton
switches. Each input includes internal debounce cir-
cuitry and a 50kpullup resistor.
The MAX5456/MAX5457 advance the wiper setting once
per button push. Maxim’s proprietary SmartWiper™ con-
trol eliminates the need for a microcomputer to increase
the wiper transition rate. Holding the control input low for
more than 1s advances the wiper at a rate of 4Hz for 4s
and 16Hz per second thereafter.
The MAX5456/MAX5457 provide temperature coeffi-
cients of 50ppm/°C end-to-end and 5ppm/°C ratiomet-
ric and a nominal resistance of 10kper potentiometer.
An integrated click/pop suppression feature minimizes
the audible noise generated by wiper transitions. The
typical total harmonic distortion plus noise (THD+N) for
these devices is 0.01%.
The MAX5457 features a 3-button interface with a
MODE input that toggles between volume- and balance-
control modes. An LED output indicates volume or bal-
ance mode. The MAX5456 features a 4-button interface
with separate inputs for up and down volume controls
and left and right balance controls.
The MAX5456/MAX5457 is available in a 16-pin QSOP
packages and specified over the extended (-40°C to
+85°C) temperature range.
Applications
Stereo Volume Control
Fading and Balancing Stereo Signals
Stereo Blending and Mixing
Features
oSmartWiper Control Provides Accelerated Wiper
Motion
oDebounced Pushbutton Interface with Internal
Pullup Resistors
oLogarithmic Taper with 2dB Steps Between Taps
oSingle +2.7V to +5.5V or Dual ±2.7V Supply
Operation
oLow 0.5µA Standby Supply Current
oClickless Switching
o10kEnd-to-End Fixed Resistance Value
oMute Function to -90dB (typ)
oPower-On Reset to -12dB Wiper Position
o32 Tap Positions for Each Wiper
oSmall 16-Pin QSOP Package
MAX5456/MAX5457
Stereo Audio Taper Potentiometers
with Pushbutton Interface
EVALUATION KIT AVAILABLE
For pricing, delivery, and ordering information, please contact Maxim Direct at
1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Ordering Information
19-3490; Rev 2; 8/12
Typical Application Circuits and Selector Guide appear at
end of data sheet.
PART TEMP RANGE PIN-PACKAGE
MAX5456EEE+ -40oC to +85oC 16 QSOP
MAX5457EEE+ -40oC to +85oC 16 QSOP
SmartWiper is a trademark of Maxim Integrated Products, Inc.
TOP VIEW
16
15
14
13
12
11
10
9
1
+
2
3
4
5
6
7
8
DN/BAL0 VDD
VLOGIC
GND
VSS
H1
L1
W1
MUTE
MAX5457
QSOP
UP/BAL1
MODE
L0
MODE_IND
H0
W0
SHDN
Pin Configurations
Pin Configurations are continued at end of data sheet.
+
Denotes a lead(Pb)-free/RoHS-compliant package.
Note: For leaded version, contact factory.
Stereo Audio Taper Potentiometers
with Pushbutton Interface
2 Maxim Integrated
MAX5456/MAX5457
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VDD = VLOGIC = +2.7V to +5.5V, VSS = 0V, GND = 0V, VH_ = VDD, VL_ = VSS, TA= TMIN to TMAX. Typical values are at TA= +25°C,
unless otherwise specified.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(MAX5456) SHDN, MUTE, VOLUP, VOLDN,
BAL_ to GND.....................................-0.3V to (VLOGIC + 0.3V)
(MAX5457) SHDN, MUTE, UP/BAL1, DN/BAL0, MODE,
MODE_IND to GND...........................-0.3V to (VLOGIC + 0.3V)
H_, L_, and W_ to VSS ..............................-0.3V to (VDD + 0.3 V)
VDD to GND..............................................................-0.3V to +6V
VDD to VSS ................................................................-0.3V to +6V
VLOGIC to GND.........................................................-0.3V to +6V
VLOGIC to VSS...........................................................-0.3V to +6V
VSS to GND............................................................-3.0V to +0.3V
Peak Current into H_, L_, and W_.......................................±1mA
Average Current into H_, L_, and W_ ..............................±500µA
Input and Output Latchup Immunity...............................±200mA
Continuous Power Dissipation (TA= +70°C)
16-Pin QSOP (derate 8.3mW/°C above +70°C)........666.7mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
End-to-End Resistance R Figures 1, 2 7 10 13 k
Maximum Bandwidth fCUTOFF From H_ to W_, CLOAD = 10pF 100 kHz
Absolute Ratio Tolerance N o l oad at the outp ut of the w i p er , W _ = - 6d B ±0.25 dB
Tap-to-Tap Tolerance ±0.1 dB
VDD = 5V, VH_ = (VDD / 2) + 1VRMS,
f = 1kHz, tap = -6dB, VL_ = VDD / 2, RL = 0.01
Total Harmonic Distortion Plus
Noise THD+N VDD = 3V, VSS = 0V, VL_ = 1.5V,
VH_ = 1.5V + 1VRMS, f = 1kHz, RL = 10k to
(VDD / 2), CL = 5pF, tap = -6dB
0.23
%
Channel-to-Channel Isolation -100 dB
Interchannel Matching f = 20Hz to 20kHz, tap = -6dB ±0.5 dB
Mute Attenuation -90 dB
Power-Supply Rejection Ratio PSRR -80 dB
Wiper Resistance RW1000 1700
Wiper Capacitance CW10 pF
H Terminal Capacitance CH5pF
L Terminal Capacitance CL7pF
End-to-End Resistance
Temperature Coefficient 50 ppm/°C
Ratiometric Resistance
Temperature Coefficient 5 ppm/°C
Output Noise en20Hz to 20kHz 0.95 µVRMS
PUSHBUTTON CONTACT INPUTS (UP/BAL1, DN/BAL0, MUTE, VOLUP, VOLDN, BAL0, BAL1, MODE)
Internal Pullup Resistor RPULLUP 32 50 65 k
Single Pulse-Width Input tlPW Figure 5 22.5 ms
Repetitive Input Pulse High Time tHPW Figure 5 40 ms
Timeout Period tWS Click/pop suppression inactive 32 ms
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 3
MAX5456/MAX5457
Note 1: Parameters are 100% production tested at +85°C and limits through temperature are guaranteed by design.
Note 2: Supply current measured with the supply on and a button pushed.
Note 3: Supply current measured with the power on, no button pushed, and the wiper position fixed.
Note 4: This is the measured current with SHDN low and MODE_IND unconnected.
ELECTRICAL CHARACTERISTICS (continued)
(VDD = VLOGIC = +2.7V to +5.5V, VSS = 0V, GND = 0V, VH_ = VDD, VL_ = VSS, TA= TMIN to TMAX. Typical values are at TA= +25°C,
unless otherwise specified.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
First Autoincrement Point 1 s
First Autoincrement Rate 4Hz
Second Autoincrement Point 4s
Second Autoincrement Rate 16 Hz
DIGITAL INPUTS (VLOGIC > 4.5V)
Input High Voltage VIH 2.4 V
Input Low Voltage VIL 0.8 V
Input Leakage Current Inputs floating ±1 µA
Input Capacitance 5pF
DIGITAL INPUTS (VLOGIC < 4.5V)
Input High Voltage VIH 0.7 x
V
L OGIC V
Input Low Voltage VIL 0.3 x
V
L OGIC V
Input Leakage Current Inputs floating ±1 µA
Input Capacitance 5pF
POWER SUPPLIES
Supply Voltage VDD 2.7 5.5 V
Negative Power Supply VSS -2.7 0 V
Supply-Voltage Difference VDD - VSS 5.5 V
Active Supply Current IDD (Note 2) 100 µA
V
D D
= + 5.5V , V
S S
= 0V , V
LOGIC = 2.7V ( N ote 3) 2 10
Standby Supply Current ISTBY VLOGIC = VDD = +2.7V, VSS = -2.7V (Note 3) 0.5 1 µA
Shutdown Supply Current ISHDN (Note 4) 1 µA
Power-Up Time tPU 10 ms
Logic Standby Voltage VLOGIC 2.7 VDD V
Logic Active Supply Current ILOGIC (Note 2) 160 µA
Logic Standby Supply Current ILOGICSTBY (Note 3) 0.5 1 µA
Logic Shutdown Current ILOGICSHDN (Note 4) 1 µA
DIGITAL OUTPUT, MODE_IND
VLOGIC = 2.7V, ISINK = 10mA 0.4
Output Low Voltage VOL VLOGIC = 5.5V, ISINK = 10mA 0.2 V
Output Leakage Current 0.1 10 µA
Output Capacitance 3pF
Maximum Sink Current 150 mA
Typical Operating Characteristics
(VDD = VLOGIC = +2.7V to +5.5V, VSS = 0V, GND = 0V, VH_ = VDD, VL_ = VSS, TA= TMIN to TMAX. Typical values are at TA= +25°C,
unless otherwise specified.)
WIPER RESISTANCE vs. WIPER VOLTAGE
MAX5456/7 toc01
WIPER VOLTAGE (V)
WIPER RESISTANCE ()
4.53.5 4.01.5 2.0 2.5 3.01.0
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
600
0.5 5.0
VDD = VLOGIC = 5V
ATTENUATION vs. TAP POSITION
MAX5456/7 toc02
TAP POSITION
ATTENUATION (dB)
282420161284
-60
-50
-40
-30
-20
-10
0
-70
032
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE
MAX5456/7 tpc03
TEMPERATURE (°C)
END-TO-END RESISTANCE CHANGE (%)
603510-15
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
-0.5
-40 85
ACTIVE SUPPLY CURRENT vs. TEMPERATURE
ACTIVE SUPPLY CURRENT (µA)
185
190
195
200
210
205
215
220
180
MAX5456/7 toc04
TEMPERATURE (°C)
603510-15-40 85
VDD = VLOGIC = 5.5V,
ILOGIC + IVDD
WIPER SWITCHING TRANSIENT
(TIMING OUT)
MAX5456/7 toc05a
10ms/div
5V/div
1V/div
VOLUP
WIPER TRANSITION
FROM -2dB to 0dB
VH_ = VDD
VL_ = 0
WIPER SWITCHING TRANSIENT
(SUPPRESSION CIRCUIT ACTIVE)
MAX5456/7 toc05b
4ms/div
5V/div
2V/div
VOLUP
WIPER TRANSITION
FROM -2dB to 0dB
VH_ = SQUARE WAVE FROM
VDD TO VSS, VL_ = VDD / 2
Stereo Audio Taper Potentiometers
with Pushbutton Interface
MAX5456/MAX5457
4 Maxim Integrated
LOGIC SUPPLY CURRENT
vs. LOGIC SUPPLY VOLTAGE
MAX5456/7 toc06a
LOGIC SUPPLY VOLTAGE (V)
LOGIC SUPPLY CURRENT (µA)
20
40
60
80
100
120
140
160
180
200
0
ACTIVE LOGIC SUPPLY
CURRENT
5.2 5.54.2 4.73.73.22.7
FREQUENCY RESPONSE
FREQUENCY (kHz)
RESPONSE (dB)
1001010.1
-6
-4
-2
0
2
-8
0.01 1000
MAX5456/7 toc08
VH_ = 2.5V ±1VP-P, VL_ = 2.5V,
CL_ = 10pF
W_ SET TO 0dB
W_ SET TO -6dB
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. FREQUENCY
FREQUENCY (Hz)
THD+N (%)
10,0001000100
0.001
0.01
0.1
1
10
100
0.0001
10 100,000
MAX5456/7 toc09
VH_ = 2.5V ±1VP-P, VL_ = 2.5V,
W_ SET TO -6dB,
20Hz TO 20kHz BANDPASS
LOAD = 10k
NO LOAD
DIGITAL SUPPLY CURRENT
vs. DIGITAL INPUT VOLTAGE
MAX5456/7 toc10
DIGITAL INPUT VOLTAGE (V)
DIGITAL SUPPLY CURRENT (µA)
4321
100
200
300
400
500
600
700
800
900
1000
0
05
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
MAX5456/7 toc11
FREQUENCY (kHz)
PSRR (dB)
10010
-80
-70
-60
-50
-40
-30
-20
-10
0
-90
1 1000
VDD = 5V ±1VP-P, VH_ = 5V,
VL_ = 2.5V, W_ SET TO -6dB
LOGIC SUPPLY CURRENT
vs. TEMPERATURE
MAX5456/7 toc12
TEMPERATURE (°C)
LOGIC SUPPLY CURRENT (mA)
603510-15
141
142
143
144
145
146
147
148
149
150
140
-40 85
VLOGIC = 5.5V
ACTIVE LOGIC SUPPLY
CURRENT
Typical Operating Characteristics (continued)
(VDD = VLOGIC = +2.7V to +5.5V, VSS = 0V, GND = 0V, VH_ = VDD, VL_ = VSS, TA= TMIN to TMAX. Typical values are at TA= +25°C,
unless otherwise specified.)
Stereo Audio Taper Potentiometers
with Pushbutton Interface
MAX5456/MAX5457
Maxim Integrated 5
0.05
0.10
0.15
0.20
0.25
0.30
0
LOGIC SUPPLY CURRENT
vs. LOGIC SUPPLY VOLTAGE
MAX5456/7 toc06b
LOGIC SUPPLY VOLTAGE (V)
LOGIC SUPPLY CURRENT (µA)
5.2 5.54.2 4.73.73.22.7
STANDBY LOGIC SUPPLY
CURRENT
WIPER-TO-END TERMINAL RESISTANCE
vs. TAP POSITION
MAX5456/7 toc07
TAP POSITION
NOMINAL END-TO-END RESISTANCE (%RHL)
24168
25
50
75
100
0
032
RWH
RWL
SPECTRAL NOISE DENSITY
MAX5456 toc13
FREQUENCY (kHz)
NOISE (nVRMS/Hz)
1010.1
1
2
3
4
5
6
7
8
9
10
0
0.01 100
Stereo Audio Taper Potentiometers
with Pushbutton Interface
6 Maxim Integrated
MAX5456/MAX5457
Pin Description
PIN
MAX5457 MAX5456
NAME FUNCTION
3—MODE
Volume/Balance Control. Each transition from high to low toggles between volume and
balance modes. MODE is pulled high internally with a 50k resistor to VLOGIC. On
power-up, the MAX5457 is in volume-control mode.
4—
MODE_IND
Volume-Control/Balance-Control Mode Indicator Open-Drain Output. Connect to
an LED through a resistor to VLOGIC. When the LED is on, the MAX5457 is in balance-
control mode. When the LED is off, the MAX5457 is in volume-control mode. See the
Mode Indicator, MODE_IND section for more detail.
5 5 H0 Potentiometer 0 High Terminal. H0 and L0 terminals can be reversed.
6 6 L0 Potentiometer 0 Low Terminal. L0 and H0 terminals can be reversed.
7 7 W0 Potentiometer 0 Wiper Terminal
88SHDN
Active-Low Shutdown Input. In shutdown mode, the MAX5456/MAX5457 store the last
wiper settings. The wipers move to the L end of the resistor string, and the H end of
the resistor string disconnects from the signal input. Terminating shutdown mode
restores the wipers to their previous settings.
99MUTE Mute Input. When MUTE is low, the wiper goes to the highest attenuation setting (see
Table 1). MUTE is internally pulled up with 50k to VLOGIC.
10 10 W1 Potentiometer 1 Wiper Terminal
11 11 L1 Potentiometer 1 Low Terminal. L1 and H1 terminals can be reversed.
12 12 H1 Potentiometer 1 High Terminal. H1 and L1 terminals can be reversed.
13 13 VSS Negative Power Supply. Bypass with 0.1µF to ground.
14 14 GND Ground
15 15 VLOGIC Digital Logic Power Supply. Bypass with 0.1µF to ground.
16 16 VDD Analog Power Supply. Bypass with 0.1µF to ground.
1—DN/BAL0
Downward Volume/Channel 0 Balance-Control Input. In volume mode, pressing
DN/BAL0 moves both wipers towards the L terminals. In balance mode, pressing
DN/BAL0 moves the balance towards channel 0. DN/BAL0 is internally pulled up with
50k to VLOGIC.
2—UP/BAL1
Upward Volume/Channel 1 Balance-Control Input. In volume mode, pressing UP/BAL1
moves both wipers towards the H terminals. In balance mode, pressing UP/BAL1
moves the balance towards channel 1. UP/BAL1 is internally pulled up with 50k to
VLOGIC.
—3BAL1 Channel 1 Balance-Control Input. Pressing BAL1 moves the balance towards channel
1. BAL1 is internally pulled up with 50k to VLOGIC.
—4BAL0 Channel 0 Balance-Control Input. Pressing BAL0 moves the balance towards channel
0. BAL0 is internally pulled up with 50k to VLOGIC.
—1VOLDN Downward Volume-Control Input. Pressing VOLDN moves both wipers towards
the L terminals. VOLDN is internally pulled up with 50k to VLOGIC.
—2VOLUP Upward Volume-Control Input. Pressing VOLUP moves both wipers towards the
H terminals. VOLUP is internally pulled up with 50k to VLOGIC.
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 7
MAX5456/MAX5457
Detailed Description
The MAX5456/MAX5457 dual, logarithmic taper digital
potentiometers feature a simple pushbutton interface that
controls volume and balance in audio applications. Each
potentiometer has 32 tap points and replaces mechanical
potentiometers (see the
Functional Diagrams
).
Up and Down Interface
The MAX5456/MAX5457 interface with momentary con-
tact SPST switches. All switch inputs are internally
debounced and pulled up to VLOGIC through 50k
resistors. The wiper setting advances once per button
press up to 1s. Maxim’s SmartWiper control circuitry
allows the wiper to advance at a rate of 4Hz when an
input is held low from 1s up to 4s, and at a rate of 16Hz
if the contact is maintained for greater than 4s (see
Table 2). The SmartWiper control eliminates the need for
a microcomputer to increase the wiper transition rate.
The MAX5456 features independent control inputs for
volume and balance control while the MAX5457 MODE
input toggles between volume and balance control.
Each transition of MODE from high to low toggles the
MAX5457 between volume-control and balance-control
modes. MODE is internally pulled high with a 50k
resistor to VLOGIC.
Volume Control
In volume-control mode, the MAX5456/MAX5457s’
wipers move simultaneously, maintaining the balance
separation between each wiper (Figure 3a).
When either wiper reaches the maximum tap position
(position closest to H_), further commands to increase
the volume are ignored. Balance separation is main-
tained in the maximum volume configuration (Figure 3b).
When either wiper reaches the minimum tap position
(position closest to L_), further commands to decrease
the volume adjust the other wiper until it also reaches
the minimum tap position (Figure 3c).
Increasing the volume from this minimum position
restores the original balance separation of the wipers
(Figure 3d).
When both wipers are in the 31st tap position (-62dB
attenuation), further commands to VOLDN place the
wipers in the mute position (see Table 1). VOLUP or
MUTE pulses return wipers to position 31.
CH
CL
CW
MAX5456
MAX5457
RW
W_
H_
L_
R
Figure 1. Potentiometer Model (Active)
CH
CL
CW
MAX5456
MAX5457
RW
W_
H_
L_
R
Figure 2. Potentiometer Model (Shutdown)
Stereo Audio Taper Potentiometers
with Pushbutton Interface
8 Maxim Integrated
MAX5456/MAX5457
(a)
W0
H_
H_
H_
H_
L_
L_
W1 W0 W0W1 W1
PRESS VOLUP
TWICE
PRESS VOLDN
ONCE
NO CHANGE
W0 W1 W0 W0W1 W1
PRESS VOLUP
ONCE PRESS VOLUP
(b)
W0 W1 W0 W0W1 W1
PRESS VOLDN
ONCE PRESS VOLDN
(c)
W0 W1 W0 W0W1 W1
PRESS VOLUP
ONCE
(d)
PRESS VOLUP
ONCE
BALANCE SEPARATION
MAINTAINED
ORIGINAL BALANCE SEPARATION
MAINTAINED
TO 3d
FROM 3c
L_
L_
Figure 3. Volume-Control Operation
Table 1. Wiper Position and Attenuation
POSITION ATTENUATION (dB)
00
12
24
6 (POR) 12
30 60
31 62
32 (mute) >90
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 9
MAX5456/MAX5457
Balance Control
In balance-control mode, the MAX5456/MAX5457
adjust the balance between channel 0 and channel 1
while maintaining the set volume. For example, if the
volume of channel 0 equals the volume of channel 1,
forcing the balance towards channel 1 increases the
attenuation of channel 0 (Figure 4a). If channel 1 is at a
higher attenuation than channel 0, adjusting the bal-
ance to channel 1 moves channel 1’s wiper up to the
same wiper position as channel 0 before attenuating
channel 0 (Figure 4b).
To control the wiper quickly with a logic signal, main-
tain pulses at least 22.5ms wide and separated by at
least 40ms.
Table 2. Wiper Action vs. Pushbutton
Contact Duration
CONTACT DURATION WIPER ACTION
t < 22.5ms No motion (debouncing).
22.5ms < t 1s Wiper changes position once.
1s < t 4s Wiper changes position
at a rate of 4Hz.
t > 4s Wiper changes position
at a rate of 16Hz.
(a)
W0
H_
L_
H_
L_
W1 W0 W0W1 W1
W0 W1 W0 W0W1 W1
(b)
VOLUME LEVEL IS SET
VOLUME LEVEL MAINTAINED
BALANCE SHIFTS TO W1
VOLUME LEVEL MAINTAINED
BALANCE SHIFTS TO W1VOLUME LEVEL IS SET BY W0
PRESS BAL1
ONCE
PRESS BAL1
ONCE
PRESS BAL1
ONCE
PRESS BAL1
ONCE
Figure 4. Balance-Control Operation
Stereo Audio Taper Potentiometers
with Pushbutton Interface
10 Maxim Integrated
MAX5456/MAX5457
Click/Pop Suppression
The click/pop suppression feature reduces the audible
noise (clicks and pops) that result from wiper transitions.
The MAX5456/MAX5457 minimize this noise by allowing
the wiper position changes only when VH_ = VL_. Thus,
the wiper changes position only when the voltage at L_ is
the same as the voltage at the corresponding H_. Each
wiper has its own suppression and timeout circuitry (see
Figure 5a). The MAX5456/MAX5457 change wiper posi-
tion after 32ms or when VH_ = VL, whichever occurs first
(see Figure 5b).
The suppression circuitry monitors left and right chan-
nels separately. In volume-control mode, when the first
wiper changes position, the second wiper has 32ms to
change or it will be forced to change.
Power-On Reset
The power-on comparators monitor VDD - VSS and
VLOGIC - GND. A power-on reset is initiated when either
of the supplies is brought back to normal operating
voltage. The power-on-reset feature sets both wipers to
-12dB. Power-on reset places the MAX5457 in volume-
control mode.
DN OR UP
1
0
USER PRESSES PUSHBUTTON
SWITCH
CONTACT
IS BOUNCING
SWITCH
CONTACT
IS STABLE
SWITCH
CONTACT
IS BOUNCING
READY TO ACCEPT
ANOTHER KEYPRESS
INPUT ACCEPTED
tIPW tWS
tHPW
DEBOUNCE BY
WAITING FOR
STABLE LOW, tIPW
WAIT FOR
FIRST ZERO
CROSSING, tWS
DEBOUNCE BY
WAITING FOR
STABLE HIGH, tHPW
VH
VL
WIPER MOTION
WIPER MOVES HERE
2dB
STEPS
Figure 5a. Wiper Transition Timing Diagram
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 11
MAX5456/MAX5457
1
0
SWITCH
CONTACT
IS BOUNCING
SWITCH
CONTACT
IS STABLE
SWITCH
CONTACT
IS BOUNCING
READY TO ACCEPT
ANOTHER KEYPRESS
INPUT ACCEPTED
tIPW tWS
tHPW
DEBOUNCE BY
WAITING FOR
STABLE LOW,
tIPW
WAIT FOR
FIRST ZERO
CROSSING OR
TIMEOUT, tWS
DEBOUNCE BY
WAITING FOR
STABLE HIGH, tHPW
VH
VL
WIPER MOVES HERE
2dB
STEPS
(tIPW + tWS)
Figure 5b. Wiper Transition Timing Diagram
Shutdown,
SHDN
Upon entering shutdown mode, the MAX5456/MAX5457
store the last wiper settings. The wipers move to the L_
end of the resistor string, and the H_ end of the resistor
string disconnects from the signal input. Terminating
shutdown mode restores the wipers to their previous
settings (see Figure 2). Shutdown does not affect the
state of MODE_IND.
Mute Function,
MUTE
The MAX5456/MAX5457 feature a mute function. Success-
ive pulses on MUTE toggle its setting. Activating the mute
function forces both wipers to maximum attenuation (-
90dB typ). Deactivating the mute function returns the
wipers to their previous settings. Pressing VOLUP also
deactivates mute, setting the wipers to their previous
positions. MUTE is internally pulled high with a 50k
resistor to VLOGIC. When both wipers are in the 31st
tap position (-62dB attenuation), further commands to
VOLDN place the wipers in the mute position (see
Table 1). VOLUP or MUTE pulses return the wipers to
position 31.
Stereo Audio Taper Potentiometers
with Pushbutton Interface
12 Maxim Integrated
MAX5456/MAX5457
Mode Control,
MODE
The MAX5457 MODE input toggles between volume-
and balance-control modes. Force MODE low to toggle
between volume-control and balance-control modes.
For example, driving MODE low once while in volume-
control mode, switches the MAX5457 to balance-con-
trol mode. Driving mode low once again, switches the
MAX5457 back to volume-control mode. MODE is inter-
nally pulled high with a 50kresistor to VLOGIC. The
MAX5457 powers up in volume-control mode.
Mode Indicator, MODE_IND
MODE_IND is the volume-control and balance-control
mode indicator with an open-drain output. Connect
MODE_IND to an LED through a pullup resistor to
VLOGIC. When the LED is on, the MAX5457 is in balance-
control mode. When the LED is off, the MAX5457 is in
volume-control mode. See the
Mode Control, MODE
sec-
tion for more detail on switching between modes.
Shutdown does not affect the state of MODE_IND.
Multiple Button Pushes
The MAX5456/MAX5457 do not respond to simultane-
ous button pushes. Pushing more than one button at the
same time stops the wipers in their present states. Only
a single button push configures the device. Additionally,
a 40ms blocking period affects all other inputs when
releasing any input forced low. The MAX5456/MAX5457
do not respond to any logic input until the blocking peri-
od ends. If multiple wiper-control buttons are pressed,
all wiper-control connections must be released before
the part will respond to further commands.
Applications Information
Stereo Volume/Balance Control
Figure 6 shows a volume/balance application using the
MAX5457. The op amp is connected in a follower (non-
inverting gain) configuration to isolate the potentiome-
ter’s wiper impedance from the load and provide drive
capability. Connect the W_ of the MAX5457 to the posi-
tive input of a noninverting gain amp. The pushbutton
potentiometers attenuate the input signals. Use the
MODE input to switch between volume-control and bal-
ance-control modes.
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 13
MAX5456/MAX5457
MUTEVSS
VDD VLOGIC
GND UP/BAL1 DN/BAL0 MODE
MAX5457
VDD / 2 VDD / 2
MAX9722
VDD VDD
MAX4494 MAX449
LEFT AUDIO
INPUT
RIGHT AUDIO
INPUT
INL- INL+ SHDN INR+ INR-
LEFT CHANNEL IN RIGHT CHANNEL IN
H0
L0
W0
H1
L1
W1
VLOGIC
VDD
MODE_INDSHDN
STEREO
HEADPHONE
OUTL OUTR
VDD
SVDD
PGND
Figure 6. Volume/Balance Control
Stereo Audio Taper Potentiometers
with Pushbutton Interface
14 Maxim Integrated
MAX5456/MAX5457
MAX5456/MAX5457
VDD
W_
L_
H_
VDD
VDD
VDD
RH
RL
VPEAK
VDD / 2
VPEAK
VDD / 2
VPEAK
VDD / 2
RLOAD =
Typical Application Circuit (Single Supply)
MAX5456/MAX5457
VDD
W_
L_
H_
VDD
RH
RL
VPEAK
0V
VPEAK
0V
VPEAK
0V
RLOAD =
VSS = -VDD
VSS
Typical Application Circuit (Dual Supplies)
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 15
MAX5456/MAX5457
DEBOUNCE DEBOUNCE DEBOUNCE DEBOUNCE
POSITION COUNTER POSITION COUNTER
VLOGIC
DEBOUNCE
T F-F
CLICK/POP
SUPPRESSION
CIRCUITRY
CLICK/POP
SUPPRESSION
CIRCUITRY
MAX5456
H0
W0
L0
H1
W1
L1
VSS GND VOLUP VOLDN BAL0 BAL1
UP/DN UP/DN
VDD VLOGIC SHDN
SHUTDOWN
0
1
2
3
4
28
29
30
31
32
MUTE
SHUTDOWN
0
1
2
3
4
28
29
30
31
32
MUTE
TIMING AND CONTROL
MUTE
Functional Diagrams
Stereo Audio Taper Potentiometers
with Pushbutton Interface
16 Maxim Integrated
MAX5456/MAX5457
DEBOUNCE DEBOUNCE DEBOUNCE DEBOUNCE
POSITION COUNTER POSITION COUNTER
VLOGIC
TIMING AND CONTROL
T F-F T F-F
CLICK/POP
SUPPRESSION
CIRCUITRY
CLICK/POP
SUPPRESSION
CIRCUITRY
MAX5457
H0
W0
L0
H1
W1
L1
VSS GND DN/BAL0 UP/BAL1 MODE MUTE
UP/DN UP/DN
VDD VLOGIC SHDN MODE_IND
SHUTDOWN
0
1
2
3
4
28
29
30
31
32
MUTE
SHUTDOWN
0
1
2
3
4
28
29
30
31
32
MUTE
Functional Diagrams (continued)
Stereo Audio Taper Potentiometers
with Pushbutton Interface
Maxim Integrated 17
MAX5456/MAX5457
16
15
14
13
12
11
10
9
1
+
2
3
4
5
6
7
8
VOLDN VDD
VLOGIC
GND
VSS
H1
L1
W1
MUTE
TOP VIEW
MAX5456
QSOP
VOLUP
BAL1
L0
BAL0
H0
W0
SHDN
Pin Configurations (continued) Chip Information
PROCESS: CMOS
Package Information
For the latest package outline information and land patterns (foot-
prints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE OUTLINE NO. LAND
PATTERN NO.
16 QSOP E16+1 21-0055 90-0167
Stereo Audio Taper Potentiometers
with Pushbutton Interface
MAX5456/MAX5457
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
18
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2012 Maxim Integrated Products, Inc. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 11/04 Initial release
2 8/12
Update Ordering Information, Absolute Maximum Ratings, Pin Description,
Pin Configuration. Removed Selector Guide and added Package
Information table and Revision History.
1, 2, 6, 14,
1820
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
MAX5456EEE+ MAX5456EEE+T MAX5456ETE+ MAX5456ETE+T MAX5457EEE+ MAX5457EEE+T
MAX5457ETE+ MAX5457ETE+T