LT1112/LT1114 Dual/Quad Low Power Precision, Picoamp Input Op Amps U DESCRIPTIO FEATURES S8 Package - Standard Pinout Offset Voltage - Prime Grade: 60V Max Offset Voltage - Low Cost Grade (Including Surface Mount Dual/Quad): 75V Max Offset Voltage Drift: 0.5V/C Max Input Bias Current: 250pA Max 0.1Hz to 10Hz Noise: 0.3VP-P, 2.2pAP-P Supply Current per Amplifier: 400A Max CMRR: 120dB Min Voltage Gain: 1 Million Min Guaranteed Specs with 1.0V Supplies Guaranteed Matching Specifications LT1114 in Narrow Surface Mount Package UO APPLICATI S Picoampere/Microvolt Instrumentation Two and Three Op Amp Instrumentation Amplifers Thermocouple and Bridge Amplifiers Low Frequency Active Filters Photo Current Amplifiers Battery-Powered Systems The LT1112 dual and LT1114 quad op amps achieve a new standard in combining low cost and outstanding precision specifications. The performance of the selected prime grades matches or exceeds competitive devices. In the design of the LT1112/ LT1114 however, particular emphasis has been placed on optimizing performance in the low cost plastic and SO packages. For example, the 75V maximum offset voltage in these low cost packages is the lowest on any dual or quad non-chopper op amp. The LT1112/LT1114 also provide a full set of matching specifications, facilitating their use in such matching dependent applications as two and three op amp instrumentation amplifiers. Another set of specifications is furnished at 1V supplies. This, combined with the low 320A supply current per amplifier, allows the LT1112/LT1114 to be powered by two nearly discharged AA cells. Protected by U.S. Patents 4,575,685; 4,775,884 and 4,837,496 Distribution of Input Offset Voltage (In All Packages) Dual Output, Buffered Reference (On Single 3V Supply) 30 3V 15k 2 - 8 1/2 LT1112 3 75k 0.1% + LT1004-1.2 6 - 5 + 25 VS = 15V TA = 25C 20 15 10 5 1/2 LT1112 46.4k 0.1% 1 TOTAL SUPPLY CURRENT = 700A 2V REFERENCE: SOURCES 1.7mA, SINKS 5mA RX OPTIONAL RX = 300 INCREASES SOURCE CURRENT TO 5mA 0.765V REFERENCE: SOURCES 5mA, SINKS 0.5mA TEMPERATURE COEFFICIENT LIMITED BY REFERENCE = 20ppm/C 2.000V MINIMUM SUPPLY = 2.7V PERCENT OF UNITS 7 0.765V 4 0 -70 -50 50 30 -30 -10 10 INPUT OFFSET VOLTAGE (V) 70 LT1112/14 * TA02 LT1112/14 * TA01 1 LT1112/LT1114 W W W AXI U U ABSOLUTE RATI GS Supply Voltage ..................................................... 20V Differential Input Current (Note 1) ..................... 10mA Input Voltage (Equal to Supply Voltage) ............... 20V Output Short-Circuit Duration ......................... Indefinite Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................ 300C Operating Temperature Range LT1112AM/LT1112M LT1114AM/LT1114M ...................... - 55C to 125C LT1112AC/LT1112C/LT1112S8 LT1114AC/LT1114C/LT1114S .......... - 40C to 85C U W U PACKAGE/ORDER I FOR ATIO TOP VIEW OUT A 1 -IN A 2 A +IN A 3 + 8 V 7 OUT B 6 -IN B 5 +IN B B V- 4 J8 PACKAGE 8-LEAD CERAMIC DIP N8 PACKAGE 8-LEAD PLASTIC DIP ORDER PART NUMBER OUT A 1 14 OUT D -IN A 2 13 -IN D +IN A 3 V+ 4 +IN B 5 -IN B 6 OUT B 7 A D 12 +IN D 11 V - B C 10 +IN C 9 -IN C 8 OUT C ORDER PART NUMBER VOS Time Long Term Input Offset Voltage Stability IOS Input Offset Current V+ 7 OUT B 6 -IN B 5 +IN B S8 PACKAGE 8-LEAD PLASTIC SO PART MARKING TJMAX = 140C, JA = 190C/W 1112 16 OUT D OUT A 1 A D +IN A 3 V+ 4 +IN B 5 15 -IN D 13 V - B C 12 +IN C -IN B 6 11 -IN C OUT B 7 10 OUT C 9 NC VS = 15V, VCM = 0V, TA = 25C, unless otherwise noted. CONDITIONS (Note 2) VS = 1.0V LT1112AM/AC LT1114AM/AC MIN TYP MAX LT1112M/C/S8 LT1114M/C/S MIN TYP MAX 20 40 25 45 60 110 0.3 Input Bias Current 2 Input Noise Voltage LT1114S 14 +IN D 0.1Hz to 10Hz (Note 9) 75 130 UNITS V V V/Mo 0.3 50 180 60 75 230 330 pA pA 70 250 80 100 280 450 pA pA 0.3 0.9 0.3 0.9 LT1114S en ORDER PART NUMBER TOP VIEW LT1114S IB LT1112S8 S PACKAGE 16-LEAD PLASTIC SO (NARROW) TJMAX = 140C, JA = 150C/W ELECTRICAL CHARACTERISTICS Input Offset Voltage ORDER PART NUMBER 8 B V- 4 NC 8 TJMAX = 160C, JA = 80C/W (J) TJMAX = 140C, JA = 110C/W (N) VOS A +IN A 3 -IN A 2 LT1114AMJ LT1114MJ LT1114ACN LT1114CN J PACKAGE N PACKAGE 14-LEAD CERAMIC DIP 14-LEAD PLASTIC DIP SYMBOL PARAMETER OUT A 1 -IN A 2 LT1112AMJ8 LT1112MJ8 LT1112ACN8 LT1112CN8 TJMAX = 160C, JA = 100C/W (J8) TJMAX = 140C, JA = 130C/W (N8) TOP VIEW TOP VIEW VP-P LT1112/LT1114 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER in VS = 15V, VCM = 0V, TA = 25C, unless otherwise noted. CONDITIONS (Note 2) LT1112AM/AC LT1114AM/AC MIN TYP MAX LT1112M/C/S8 LT1114M/C/S MIN TYP MAX UNITS 16 14 nV/Hz nV/Hz Input Noise Voltage Density fO = 10Hz (Note 9) fO = 1000Hz (Note 9) 16 14 Input Noise Current 0.1Hz to 10Hz 2.2 2.2 Input Noise Current Density fO = 10Hz fO = 1000Hz 0.030 0.008 0.030 0.008 pA/Hz pA/Hz 14.3 V 13.5 28 18 14.3 13.5 28 18 pAP-P VCM Input Voltage Range CMRR Common-Mode Rejection Ratio VCM = 13.5V 120 136 115 136 dB PSRR Power Supply Rejection Ratio VS = 1.0V to 20V 116 126 114 126 dB Minimum Supply Voltage (Note 4) 1.0 Input Resistance Differential Mode Common Mode (Note 3) 20 50 800 15 40 700 M G RIN 1.0 V AVOL Large-Signal Voltage Gain VO = 12V, RL = 10k VO = 10V, RL = 2k 1000 800 5000 1500 800 600 5000 1300 V/mV V/mV VOUT Output Voltage Swing RL = 10k RL = 2k 13.0 11.0 14.0 12.4 13.0 11.0 14.0 12.4 V V SR Slew Rate 0.16 0.30 0.16 0.30 V/s GBW Gain-Bandwidth Product 450 750 450 750 kHz IS Supply Current per Amplifier fO = 10kHz 350 320 Channel Separation fO = 10Hz 150 VOS Offset Voltage Match (Note 5) 35 100 40 130 V IB Noninverting Bias Current Match (Notes 5, 6) 100 450 LT1114S 100 120 500 680 pA pA CMRR Common-Mode Rejection Match (Notes 5, 7) 117 136 113 136 dB PSRR Power Supply Rejection Match (Notes 5, 7) 114 130 112 130 dB + ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER 400 370 350 320 450 420 A A VS = 1.0V 150 dB VS = 15V, - 55C TA 125C, unless otherwise noted. CONDITIONS (Note 2) LT1112AMJ8 LT1114AMJ MIN TYP MAX LT1112MJ8 LT1114MJ MIN TYP MAX UNITS VS = 1.2V 35 60 120 220 45 70 150 260 V V (Note 8) 0.15 0.5 0.20 0.75 V/C VOS Input Offset Voltage VOS Temp Average Input Offset Voltage Drift IOS Input Offset Current 80 400 100 500 pA IB Input Bias Current 150 600 170 700 pA VCM Input Voltage Range 13.5 14.1 13.5 14.1 V CMRR Common-Mode Rejection Ratio VCM = 13.5V 116 130 111 130 dB PSRR Power Supply Rejection Ratio VS = 1.2V to 20V 112 124 110 124 dB AVOL Large-Signal Voltage Gain VO = 12V, RL = 10k VO = 10V, RL = 2k 500 200 2500 600 400 170 2500 500 V/mV V/mV 3 LT1112/LT1114 ELECTRICAL CHARACTERISTICS VS = 15V, - 55C TA 125C, unless otherwise noted. SYMBOL PARAMETER CONDITIONS (Note 2) VOUT Output Voltage Swing RL = 10k SR Slew Rate IS Supply Current per Amplifier VOS Offset Voltage Match (Note 5) Offset Voltage Match Drift (Notes 5, 8) IB+ Noninverting Bias Current Match CMRR PSRR LT1112AMJ8 LT1114AMJ MIN TYP MAX LT1112MJ8 LT1114MJ MIN TYP MAX 13.0 13.85 13.0 13.85 0.12 0.22 0.12 UNITS V 0.22 V/s A 380 460 55 0.2 (Notes 5, 6) 150 Common-Mode Rejection Ratio (Notes 5, 7) 112 130 106 130 dB Power Supply Rejection Ratio (Notes 5, 7) 109 126 106 126 dB ELECTRICAL CHARACTERISTICS 380 530 200 70 240 V 0.7 0.3 1.0 V/C 750 170 850 pA VS = 15V, 0C TA 70C, unless otherwise noted. LT1112ACN8 LT1114ACN MIN TYP MAX LT1112N8/S8 LT1114CN/S MIN TYP MAX SYMBOL PARAMETER CONDITIONS (Note 2) VOS Input Offset Voltage LT1112N8 LT1112S8, LT1114N/S VS = 1.2V 27 35 50 100 125 175 30 45 65 125 150 210 V V V VOS Temp Average Input Offset Voltage Drift (Note 8) LT1112N8 LT1112S8, LT1114N/S 0.15 0.3 0.5 1.1 0.2 0.4 0.75 1.3 V/C V/C IOS Input Offset Current 60 220 LT1114S 70 90 290 420 pA pA 80 300 LT1114S 90 115 350 550 pA pA IB Input Bias Current UNITS VCM Input Voltage Range 13.5 14.2 13.5 14.2 V CMRR Common-Mode Rejection Ratio VCM = 13.5V 118 133 113 133 dB PSRR Power Supply Rejection Ratio VS = 1.2V to 20V 114 125 112 125 dB AVOL Large-Signal Voltage Gain VO = 12V, RL = 10k VO = 10V, RL = 2k 800 500 4000 1300 650 400 4000 1000 V/mV V/mV VOUT Output Voltage Swing RL = 10k 13.0 13.9 13.0 13.9 V SR Slew Rate 0.14 0.27 0.14 0.27 V/s IS Supply Current per Amplifier 370 440 370 500 A VOS Offset Voltage Match (Note 5) LT1112N8 LT1112S8, LT1114N/S 45 55 170 220 55 70 210 270 V V Offset Voltage Match Drift (Notes 5, 8) LT1112N8 LT1112S8, LT1114N/S 0.2 0.4 0.7 1.6 0.3 0.5 1.0 1.9 V/C V/C Noninverting Bias Current Match (Notes 5, 6) 120 530 LT1114S 135 160 620 880 pA pA CMRR Common-Mode Rejection Ratio (Notes 5, 7) 114 134 109 134 dB PSRR Power Supply Rejection Ratio (Notes 5, 7) 110 128 108 128 dB IB+ 4 LT1112/LT1114 ELECTRICAL CHARACTERISTICS VS = 15V, - 40C TA 85C, (Note 10) LT1112ACN8 LT1114ACN MIN TYP MAX LT1112N8/S8 LT1114CN/S MIN TYP MAX SYMBOL PARAMETER CONDITIONS (Note 2) VOS Input Offset Voltage LT1112N8 LT1112S8, LT1114N/S VS = 1.2V 30 40 55 110 135 200 35 45 60 135 160 240 V V V VOS Temp Average Input Offset Voltage Drift LT1112N8 LT1112S8, LT1114N/S 0.15 0.30 0.50 1.10 0.20 0.40 0.75 1.30 V/C V/C IOS Input Offset Current 70 330 LT1114S 85 110 400 600 pA pA 110 500 LT1114S 120 150 550 800 pA pA IB Input Bias Current UNITS 13.5 14.1 13.5 14.1 V VCM = 13.5V 117 132 112 132 dB VS = 1.2V to 20V 113 125 111 125 dB VO = 12V, RL = 10k VO = 10V, RL = 2k 700 400 3300 1100 600 300 3300 900 V/mV V/mV RL = 10k VCM Input Voltage Range CMRR Common-Mode Rejection Ratio PSRR Power Supply Rejection Ratio AVOL Large-Signal Voltage Gain VOUT Output Voltage Swing SR Slew Rate IS Supply Current per Amplifier 370 450 370 510 A VOS Offset Voltage Match (Note 5) LT1112N8 LT1112S8, LT1114N/S 50 60 180 230 60 70 225 270 V V Offset Voltage Match Drift (Notes 5) LT1112N8 LT1112S8, LT1114N/S 0.2 0.4 0.7 1.6 0.3 0.5 1.0 1.9 V/C V/C Noninverting Bias Current Match (Notes 5, 6) 140 660 LT1114S 155 190 770 1300 CMRR Common-Mode Rejection Ratio (Notes 5, 7) 113 133 109 133 dB PSRR Power Supply Rejection Ratio (Notes 5, 7) 110 127 107 127 dB IB+ The denotes specifications which apply over the operating temperature range. Note 1: Differential input voltages greater than 1V will cause excessive current to flow through the input protection diodes unless limiting resistance is used. Note 2: Typical parameters are defined as the 60% yield of parameter distributions of individual amplifiers; i.e., out of 100 LT1114s (or 100 LT1112s) typically 240 op amps (or 120) will be better than the indicated specification. Note 3: This parameter is guaranteed by design and is not tested. Note 4: Offset voltage, supply current and power supply rejection ratio are measured at the minimum supply voltage. Note 5: Matching parameters are the difference between amplifiers A and D and between B and C on the LT1114; between the two amplifiers on the LT1112. 13.0 13.85 0.13 13.0 13.85 0.24 0.13 V 0.24 V/s pA pA Note 6: This parameter is the difference between two noninverting input bias currents. Note 7: CMRR and PSRR are defined as follows: (1) CMRR and PSRR are measured in V/V on the individual amplifiers. (2) The difference is calculated between the matching sides in V/V. (3) The result is converted to dB. Note 8: This parameter is not 100% tested. Note 9: These parameters are not tested. More than 99% of the op amps tested during product characterization have passed the maximum limits. 100% passed at 1kHz. Note 10: The LT1112/LT1114 are not tested and are not quality assurance sampled at - 40C and at 85C. These specifications are guaranteed by design, correlation and/or inference from - 55C, 0C, 25C, 70C and/or 125C tests. 5 LT1112/LT1114 U W TYPICAL PERFOR A CE CHARACTERISTICS Input Bias Current Over Common-Mode Range IOS IB (UNDERCANCELLED) 0 IB (OVERCANCELLED) -100 30 VS = 15V TA = 25C RINCM = 800G 50 VS = 15V TA = 25C DEVICE WITH POSITIVE INPUT CURRENT 0 DEVICE WITH NEGATIVE INPUT CURRENT -50 - IB -100 VS = 15V -200 -75 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 -150 -15 + 10 -5 0 5 -10 COMMON-MODE INPUT VOLTAGE (V) 0 0 100 200 -300 -200 -100 INPUT BIAS CURRENT (pA) 15 Distribution of Offset Voltage at VS = 1.0V (In All Packages) 25 PERCENT OF UNITS 20 10 5 960 OP AMPS TESTED 240 LT1112S8 80 LT1114N 40 LT1114S 30 VS = 15V TA = 25C 25 PERCENT OF UNITS VS = 15V 15 10 5 20 15 10 5 0 0.6 1.0 1.4 -1.4 -1.0 -0.6 -0.2 0.2 OFFSET VOLTAGE DRIFT WITH TEMPERATURE (V/C) 0 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 OFFSET VOLTAGE DRIFT WITH TEMPERATURE (V/C) 0 -80 -60 -40 -20 0 20 40 60 80 100 INPUT OFFSET VOLTAGE (V) LT1112/14 * TPC05 LT1112/14 * TPC04 LT1112/14 * TPC06 Distribution of Offset Voltage Match Drift (LT1112J8, LT1112N8, LT1114J Packages) Distribution of Offset Voltage Match Distribution of Offset Voltage Match Drift (LT1112S8, LT1114N, LT1114S Packages) 20 30 25 VS = 15V TA = 25C 25 20 300 LT1112/14 * TPC03 Drift with Temperature LT1112S8, LT1114N/S 20 VS = 15V 342 PAIRS TESTED VS = 15V 364 PAIRS TESTED PERCENT ON UNITS 15 15 10 PERCENT OF UNITS PERCENT OF INPUTS 10 LT1112/14 * TPC02 Drift with Temperature LT1112N8/J8, LT1114J 850 OP AMPS TESTED 100 LT1112J8 165 LT1112N8 80 LT1114J 20 VCM LT1112/14 * TPC01 PERCENT OF UNITS PERCENT OF UNITS 100 IB+ 100 15 Distribution of Input Bias Current (In All Packages Except LT1114S) 150 200 INPUT BIAS CURRENT (pA) INPUT BIAS, OFFSET, MATCH CURRENT (pA) Input Bias and Offset Current, Noninverting Bias Current Match vs Temperature 20 15 10 10 5 5 5 0 -100 -80 -60 - 40 -20 0 20 40 60 80 100 VOS, OFFSET VOLTAGE MATCH (V) 0 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 OFFSET VOLTAGE MATCH DRIFT (V/C) LT1112/14 * TPC07 6 LT1112/14 * TPC08 0 -1.6 -1.2 -0.8 -0.4 0 0.4 0.8 1.2 1.6 OFFSET VOLTAGE MATCH DRIFT (V/C) LT1112/14 * TPC09 LT1112/LT1114 U W TYPICAL PERFOR A CE CHARACTERISTICS Noise Spectrum 0.1Hz to 10Hz Noise 0.01Hz to 1Hz Noise VS = 1V TO 20V TA = 25C CURRENT NOISE VOLTAGE NOISE 10 1/fCORNER 2.5Hz VS = 15V TA = 25C 1/fCORNER 140Hz NOISE VOLTAGE (0.2V/DIV) 100 VS = 15V TA = 25C NOISE VOLTAGE (0.2V/DIV) VOLTAGE NOISE DENSITY (nV/Hz) CURRENT NOISE DENSITY (fA/Hz) 1000 1 1 10 100 FREQUENCY (Hz) 1000 2 0 6 4 TIME (SEC) LT1112/14 * TPC10 LT1112S8, LT1114N/S PACKAGES LT1114J PACKAGE LT1112J8, N8 PACKAGES 4 2A 3A 2 2B 0 1A 3B -2 1B -4 -6 0 2.5 0 1 2 3 4 TIME (MONTHS) COMMON-MODE RANGE OR OUTPUT SWING (V) 1.1 1.0 0.9 100 80 60 40 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 LT1112/14 * TPC16 400 TA = 125C TA = 25C 300 TA = -55C 200 6 0 10 15 5 SUPPLY VOLTAGE (V) Output Voltage Swing vs Load Current V+ V + - 0.2 V+ VS = 1V TO 20V IL < 100A V+ - 1 V + - 0.4 SWING V + - 0.6 V + - 0.8 V + - 1.0 CM RANGE V - + 0.8 SWING V - + 0.6 V - + 0.4 CM RANGE VS = 1V TO 20V TA = 25C MAX IL AT 1V = 1.3mA AT 1.5V = 3mA V+ - 2 V+ - 3 V- + 3 V- + 2 V- + 1 V - + 0.2 V- -75 20 LT1112/14 * TPC15 Common-Mode Range and Voltage Swing with Respect to Supply Voltages Minimum Supply Voltage vs Temp Voltage Gain at Minimum Supply Voltage 100 500 LT1112/14 * TPC14 LT1112/14 * TPC13 1.2 5 OUTPUT SWING (V) 0.5 1.0 1.5 2.0 TIME AFTER POWER ON (MINUTES) 80 600 VS = 15V TA = 25C SUPPLY CURRENT PER AMPLIFIER (A) CHANGE IN OFFSET VOLTAGE (V) CHANGE IN OFFSET VOLTAGE (V) 2 0 60 40 TIME (SEC) Supply Current per Amplifier vs Supply Voltage 6 VS = 15V TA = 25C 1 20 LT1112/14 * TPC12 Long Term Stability of Three Representative Units 3 MINIMUM SUPPLY (V) 0 10 LT1112/14 * TPC11 Warm-Up Drift VOLTAGE GAIN (V/mV) 8 -25 25 75 TEMPERATURE (C) 125 LT1112/14 * TPC17 V- -9 -6 SINK 0 3 6 SOURCE OUTPUT CURRENT (mA) -3 9 LT1112/14 * TPC18 7 LT1112/LT1114 U W TYPICAL PERFOR A CE CHARACTERISTICS Voltage Gain 100 40 140 VS = 15V TA = 25C VS = 15V TA = 25C VS = 15V TA = 25C 120 120 -5 RL = 10k 0 RL = 2k 5 PHASE 80 GAIN (dB) VOLTAGE GAIN (dB) 30 100 60 40 20 140 20 GAIN 160 10 0 10 15 -15 -10 -5 0 5 OUTPUT VOLTAGE (V) 10 -20 0.01 0.1 15 1 -10 0.01 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 180 PHASE MARGIN = 70C 0 PHASE SHIFT (DEG) CHANGE IN OFFSET VOLTAGE (V) -15 -10 Gain, Phase Shift vs Frequency Voltage Gain vs Frequency 200 0.1 1 10 FREQUENCY (MHz) LT1112/14 * TPC21 LT1112/14 * TPC19 LT1112/14 * TPC20 Common-Mode Rejection vs Frequency Power Supply Rejection vs Frequency 100 80 60 40 20 10 10k 1k 100 FREQUENCY (Hz) 100k NEGATIVE SUPPLY 100 80 POSITIVE SUPPLY 60 1M 1 10 100 1k 10k FREQUENCY (Hz) 1M SLEW 70 800 60 700 OUTPUT IMPEDANCE () 80 GBW 100 125 LT1112/14 * TPC25 100k 1M Capacitive Loading Handling 120 100 10 AV = 100 AV = +1 1 0.1 VS = 15V TA = 25C 80 60 AV = +1 40 AV = 10 0.01 50 25 0 75 TEMPERATURE (C) 1k 100 10k FREQUENCY (Hz) 10 LT1112/14 * TPC24 VS = 15V TA = 25C 100 m AMP 1 IN UNITY-GAIN 20VP-P, RL = 2k AMP 2 IN GAIN = 1000 RS = 100, RF = 100k 1 1000 PHASE MARGIN (DEG) GAIN-BANDWIDTH PRODUCT (kHz) SLEW RATE (V/s) 100k Closed-Loop Output Impedance 0.4 600 -50 -25 100 LT1112/14 * TPC23 Slew Rate, Gain-Bandwidth Product and Phase Margin vs Temperature 0.2 120 80 LT1112/14 * TPC22 0.3 140 40 OVERSHOOT (%) 1 120 20 0.1 0 VS = 15V TA = 25C VS = 15V TA = 25C CHANNEL SEPARATION (dB) POWER SUPPLY REJECTION RATIO (dB) COMMON-MODE REJECTION RATIO (dB) VS = 15V TA = 25C 120 8 Channel Separation vs Frequency 160 140 140 0.001 20 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M LT1112/14 * TPC26 0 0.1 0.00001 0.0001 0.001 0.01 CAPACITIVE LOAD (F) 1 10 LT1112/14 * TPC27 LT1112/LT1114 U W TYPICAL PERFOR A CE CHARACTERISTICS Small-Signal Transient Response Undistorted Output Voltage vs Frequency Large-Signal Transient Response PEAK-TO-PEAK OUTPUT VOLTAGE (V) 5V/DIV 20mV/DIV 28 50s/DIV 2s/DIV AV = +1 RF = 10k CF = 100pF VS = 15V W U UO APPLICATI VS = 15V 20 16 12 8 VS = 5V 4 0 1 10 100 FREQUENCY (kHz) 1000 LT1112/14 * TPC30 U AV = +1 CL = 500pF VS = 15V TA = 25C RL = 10k 24 S I FOR ATIO The LT1112 dual and LT1114 quad in the plastic and ceramic DIP packages are pin compatible to and directly replace such precision op amps as the OP-200, OP-297, AD706 duals and OP-400, OP-497, AD704 quads with improved price/performance. the input is driven by a fast large-signal pulse (>1V), the input protection diodes effectively short the output to the input during slewing, and a current, limited only by the output short-circuit protection, will flow through the diodes. The LT1112 in the S8 surface mount package has the standard pin configuration, i.e., the same configuration as the plastic and ceramic DIP packages. The use of a feedback resistor is recommended because this resistor keeps the current below the short-circuit limit, resulting in faster recovery and settling of the output. The LT1114 quad is offered in the narrow 16-pin surface mount package. All competitors are in the wide 16-pin package which occupies 1.8 times the area of the narrow package. The wide package is also 1.8 times thicker than the narrow package. The input voltage of the LT1112/1114 should never exceed the supply voltages by more than a diode drop. However, the example below shows that as the input voltage exceeds the common-mode range, the LT1112's output clips cleanly, without any glitches or phase reversal. The OP297 exhibits phase reversal. The photos also illustrate that both the input and output ranges of the LT1112 are within The inputs of the LT1112/1114 are protected with back-toback diodes. In the voltage follower configuration, when Voltage Follower with Input Exceeding the Common-Mode Range (VS = 5V) INPUT: 5.2V Sine Wave LT1112 Output OP-297 Output 9 LT1112/LT1114 U W U UO APPLICATI S I FOR ATIO 800mV of the supplies. The effect of input and output overdrive on the other amplifiers in the LT1112 or LT1114 packages is negligible, as each amplifier is biased independently. Input offset current = 100pA Input resistance = 800G Input noise = 0.42VP-P Three Op Amp Instrumentation Amplifier Advantages of Matched Dual and Quad Op Amps In many applications the performance of a system depends on the matching between two operational amplifiers rather than the individual characteristics of the two op amps. Two or three op amp instrumentation amplifiers, tracking voltage references and low drift active filters are some of the circuits requiring matching between two op amps. The well-known triple op amp configuration illustrates these concepts. Output offset is a function of the difference between the offsets of the two halves of the LT1112. This error cancellation principle holds for a considerable number of input referred parameters in addition to offset voltage and its drift with temperature. Input bias current will be the average of the two noninverting input currents (IB+). The difference between these two currents (IB+) is the offset current of the instrumentation amplifier. Common-mode and power supply rejections will be dependent only on the match between the two amplifiers (assuming perfect resistor matching). The concepts of common-mode and power supply rejection ratio match (CMRR and PSRR) are best demonstrated with a numerical example: Assume CMRRA = + 1V/V or 120dB, and CMRRB = + 0.75V/V or 122.5dB, then CMRR = 0.25V/V or 132dB; if CMRRB = - 0.75V/V which is still 122.5dB, then CMRR = 1.75V/V or 115dB. Clearly the LT1112/LT1114, by specifying and guaranteeing all of these matching parameters, can significantly improve the performance of matching-dependent circuits. Typical performance of the instrumentation amplifier: Input offset voltage = 35V Offset voltage drift = 0.3V/C Input bias current = 80pA 10 IN- R4 100 0.5% + 1/2 LT1112 OR 1/4 LT1114 - A R6 10k 0.5% R1 10k 1% - R3 2.1k 1% R8 200 - IN+ 1/2 LT1112 OR 1/4 + LT1114 D C1 33pF R10 1M R2 R5 10k 100 1% 0.5% LT1097 OR 1/4LT1114 +B OR C OUTPUT GAIN = 1000 R7 9.88k 0.5% TRIM R8 FOR GAIN TRIM R9 FOR DC COMMON-MODE REJECTION TRIM R10 FOR AC COMMON-MODE REJECTION R9 200 LT1112/14 * AI02 When the instrumentation amplifier is used with high impedance sources, the LT1114 is recommended because its CMRR vs frequency performance is better than the LT1112's. For example, with two matched 1M source resistors, CMRR at 100Hz is 100dB with the LT1114, 76dB with the LT1112. This difference is explained by the fact that capacitance between adjacent pins on an IC package is about 0.25pF (including package, socket and PC board trace capacitances). On the dual op amp package, positive input A is next to the V - pin (AC ground), while positive input B has no AC ground pin adjacent to it, resulting in a 0.25pF input capacitance mismatch. At 100Hz, 0.25pF represents a 6.4 x 109 input impedance mismatch, which is only 76dB higher than the 1M source resistors. On the quad package, all four inputs are adjacent to a power supply terminal-therefore, there is no mismatch. LT1112/LT1114 UO TYPICAL APPLICATI Dual Buffered 0.617V Reference Powered by Two AA Batteries +1.5V RX* 15k *OPTIONAL + 1/2 LT1112 +0.617V - 20k 0.1% LT1004-1.2 TOTAL SUPPLY CURRENT = 700A WORKS WITH BATTERIES DISCHARGED TO 1.3V AT 1.5V: MAXIMUM LOAD CURRENT = 800A; CAN BE INCREASED WITH OPTIONAL RX, RY; AT RX = RY = 750 LOAD CURRENT = 2mA TEMPERATURE COEFFICIENT LIMITED BY REFERENCE = 20ppm/C 100pF - 1/2 LT1112 + RY* 20k 0.1% *OPTIONAL -1.5V -0.617V LT1112/14 * TA03 W W SCHE ATIC DIAGRA (1/2 LT1112, 1/4 LT1114) 12pF 30k V+ 20A 30k 35A Q35 Q34 Q19 Q22 30pF 800 80A 1.5k 4k Q33 Q21 Q6 Q5 Q25 Q27 Q29 S Q8 Q4 Q24 28 Q7 3k 90 OUT Q13 Q11 Q23 INVERTING INPUT S - 2.5k S Q1 Q2 Q20 S Q3 50k 1.5k Q26 J1 30 Q28 Q32 Q9 NONINVERTING INPUT Q12 Q16 10k Q18 Q10 + Q30 Q17 460 Q31 15A 5A Q14 Q15 5A V- 200 460 200 460 Q1 TO Q4 ARE SUPERGAIN TRANSISTORS Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of circuits as described herein will not infringe on existing patent rights. LT1112/14 * SD01 11 LT1112/LT1114 U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. 0.290 - 0.320 (7.366 - 8.128) J8 Package 8-Lead Ceramic DIP 0.015 - 0.060 (0.381 - 1.524) 0.008 - 0.018 (0.203 - 0.460) 0.405 (10.287) MAX 0.005 (0.127) MIN 0.200 (5.080) MAX 8 0.025 (0.635) RAD TYP 0.220 - 0.310 (5.588 - 7.874) 1 0.038 - 0.068 (0.965 - 1.727) 0.300 - 0.320 (7.620 - 8.128) 0.045 - 0.065 (1.143 - 1.651) N8 Package 8-Lead Plastic DIP 3 +0.025 0.325 -0.015 8 7 6 5 0.250 0.010 (6.350 0.254) 0.125 (3.175) MIN 0.045 0.015 (1.143 0.381) ) 4 0.400 (10.160) MAX 0.130 0.005 (3.302 0.127) 0.065 (1.651) TYP 0.009 - 0.015 (0.229 - 0.381) +0.635 -0.381 2 0.055 (1.397) MAX 0.125 3.175 0.100 0.010 MIN (2.540 0.254) 0.014 - 0.026 (0.360 - 0.660) 8.255 5 0 - 15 0.385 0.025 (9.779 0.635) ( 6 7 0.020 (0.508) MIN 1 2 4 3 0.018 0.003 (0.457 0.076) 0.100 0.010 (2.540 0.254) 0.189 - 0.197 (4.801 - 5.004) 0.010 - 0.020 x 45 (0.254 - 0.508) S8 Package 8-Lead Plastic SOIC 0.014 - 0.019 (0.355 - 0.483) 0.228 - 0.244 (5.791 - 6.197) 0.050 (1.270) BSC 0.150 - 0.157 (3.810 - 3.988) 1 0.005 (0.127) MIN 0.200 (5.080) MAX 0.290 - 0.320 (7.366 - 8.128) J Package 14-Lead Ceramic DIP 0.015 - 0.060 (0.381 - 1.524) 0.008 - 0.018 (0.203 - 0.460) 0.038 - 0.068 (0.965 - 1.727) 0.100 0.010 (2.540 0.254) 0.014 - 0.026 (0.360 - 0.660) 0.300 - 0.325 (7.620 - 8.255) 14 12 13 11 10 9 8 0.220 - 0.310 (5.588 - 7.874) 0.025 (0.635) RAD TYP 2 ) 4 5 6 7 0.770 (19.558) MAX 0.065 (1.651) TYP 14 13 12 11 10 9 8 1 2 3 4 5 6 7 0.260 0.010 (6.604 0.254) 0.009 - 0.015 (0.229 - 0.381) +0.025 0.325 -0.015 3 0.098 (2.489) MAX 0.125 (3.175) MIN 0.045 - 0.065 (1.143 - 1.651) 0.015 (0.380) MIN 0.130 0.005 (3.302 0.127) N Package 14-Lead Plastic DIP ( 4 0.785 (19.939) MAX 1 +0.635 -0.381 3 2 0 - 15 0.385 0.025 (9.779 0.635) 8.255 5 6 0.004 - 0.010 (0.101 - 0.254) 0.016 - 0.050 0.406 - 1.270 0- 8 TYP 7 8 0.053 - 0.069 (1.346 - 1.752) 0.008 - 0.010 (0.203 - 0.254) 0.075 0.015 (1.905 0.381) 0.018 0.003 (0.457 0.076) 0.100 0.010 (2.540 0.254) 0.125 (3.175) MIN 0.386 - 0.394 (9.804 - 10.008) 0.010 - 0.020 x 45 (0.254 - 0.508) S Package 16-Lead Plastic SOIC 16 0.004 - 0.010 (0.101 - 0.254) 0.053 - 0.069 (1.346 - 1.752) 14 13 12 11 10 9 0.008 - 0.010 (0.203 - 0.254) 0 - 8 TYP 0.016 - 0.050 0.406 - 1.270 0.014 - 0.019 (0.355 - 0.483) 0.050 (1.270) TYP 0.150 - 0.157 (3.810 - 3.988) 0.228 - 0.244 (5.791 - 6.197) 1 12 15 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 FAX: (408) 434-0507 TELEX: 499-3977 2 3 4 5 6 7 8 LT/GP 1292 10K REV 0 LINEAR TECHNOLOGY CORPORATION 1992