B39162B3529U410 - RF 360 - Datasheet.Directory

RF360 Europe GmbH

A Qualcomm – TDK Joint Venture

RF360 products mentioned within this document are offered by RF360 Europe GmbH and other subsidiaries of

RF360 Holdings Singapore Pte. Ltd. (collectively, the “RF360 Subsidiaries”). RF360 Holdings Singapore Pte. Ltd.

is a joint venture of Qualcomm Global Trading Pte. Ltd. and EPCOS AG. References in this documentation to

EPCOS AG should properly reference, and shall be read to reference, the RF360 Subsidiaries.

RF360 Europe GmbH, Anzinger Str. 13, München, Germany

SAW Components

SAW RF filter

Automotive telematics

Series/type: B3529

Ordering code: B39162B3529U410

Date: May 22, 2013

Version: 2.3

These materials, including the information contained herein, may be used only for informational purposes by

the customer. The RF360 Subsidiaries assume no responsibility for errors or omissions in these materials or

the information contained herein. The RF360 Subsidiaries reserve the right to make changes to the product(s)

or information contained herein without notice. The materials and information are provided on an AS IS basis,

and the RF360 Subsidiaries assume no liability and make no warranty or representation, either expressed or

implied, with respect to the materials, or any output or results based on the use, application, or evaluation of

such materials, including, without limitation, with respect to the non-infringement of trademarks, patents,

copyrights or any other intellectual property rights or other rights of third parties.

No use of this documentation or any information contained herein grants any license, whether express, implied,

by estoppel or otherwise, to any intellectual property rights, including, without limitation, to any patents owned

by QUALCOMM Incorporated or any of its subsidiaries.

Not to be used, copied, reproduced, or modified in whole or in part, nor its contents revealed in any manner to

others without the express written permission of RF360 Europe GmbH.

Qualcomm and Qualcomm RF360 are trademarks of Qualcomm Incorporated, registered in the United States

and other countries. RF360 is a trademark of Qualcomm Incorporated. Other product and brand names may be

trademarks or registered trademarks of their respective owners.

This technical data may be subject to U.S. and international export, re-export, or transfer (“export”) laws.

Diversion contrary to U.S. and international law is strictly prohibited.

SAW Components

SAW RF filter

Automotive telematics

Series/type:

Ordering code: B3529

B39162B3529U410

Date:

Version: May 22, 2013

2.3

 EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information

contained therein without EPCOS' prior express consent is prohibited.

EPCOS AG is a TDK Group Company.

2May 22, 2013

B3529

1601.50 MHz

Please read

cautions and warnings and

important notes

at the end of this document.

SAW Components

SAW RF filter

Data sheet

Application

■Low-loss RF filter for Glonass application

■No matching network required for operation at 50 Ω

Features

■Package size 3.0 x 3.0 x 1.1 mm3

■Package code DCC6C

■RoHS compatible

■Approximate weight 0.037 g

■Package for Surface Mount Technology

(SMT)

■Ni, gold-plated terminals

■Lead free soldering compatible with J - STD20C

■AEC-Q200 qualified component family

■Electrostatic Sensitive Device (ESD)

Pin configuration

■2 Input

■5 Output

■1, 3, 4, 6 Ground

3May 22, 2013

B3529

1601.50 MHz

SAW Components

SAW RF filter

Data sheet

Please read

cautions and warnings and

important notes

at the end of this document.

Characteristics

Temperature range for specification: T = –40 ˚C to +85 ˚C

Terminating source impedance: ZS=50Ω

Terminating load impedance: ZL=50Ω

min. typ.

@ 25 ˚C max.

Center frequency fC— 1601.5 — MHz

Maximum insertion attenuation αmax

1593.00 ... 1610.00 MHz — 2.5 4.0 dB

Amplitude ripple (p-p) ∆α

1593.00 ... 1610.00 MHz — 0.6 2.5 dB

Group delay ripple (p-p) ∆τ

1593.00 ... 1610.00 MHz — 12 27 ns

VSWR 1593.00 ... 1610.00 MHz — 1.6 2.0

Attenuation α

700.00 ... 1400.00 MHz 40 44 — dB

1400.00 ... 1530.00 MHz 35 40 — dB

1530.00 ... 1570.00 MHz 10 12 — dB

1625.00 ... 1640.00 MHz 10 25 — dB

1640.00 ... 1650.00 MHz 22 37 — dB

1650.00 ... 1670.00 MHz 30 48 — dB

1670.00 ... 1870.00 MHz 40 43 — dB

1870.00 ... 2270.00 MHz 35 38 — dB

2270.00 ... 2700.00 MHz 30 35 — dB

4May 22, 2013

B3529

1601.50 MHz

Please read

cautions and warnings and

important notes

at the end of this document.

SAW Components

SAW RF filter

Data sheet

Maximum ratings

Operable temperature range T –45/+125 ˚C

Storage temperature range Tstg –45/+125 ˚C

DC voltage VDC 6 V

Source power PS10 dBm source impedance 50 Ω

5May 22, 2013

B3529

1601.50 MHz

SAW Components

SAW RF filter

Data sheet

Please read

cautions and warnings and

important notes

at the end of this document.

Transfer function

Transfer function (wideband)

6May 22, 2013

B3529

1601.50 MHz

Please read

cautions and warnings and

important notes

at the end of this document.

SAW Components

SAW RF filter

Data sheet

Transfer function

7May 22, 2013

B3529

1601.50 MHz

SAW Components

SAW RF filter

Data sheet

Please read

cautions and warnings and

important notes

at the end of this document.

ESD protection of SAW filters

SAW filters are Electro Static Discharge sensitive devices. To reduce the probability of damages

caused by ESD, special matching topologies have to be applied.

In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is

expected.

Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore

only the input matching of the SAW filter has to be designed to short circuit or to block the ESD

pulse.

Below three figures show recommended “ESD matching” topologies.

For wideband filters the high-pass ESD matching structure needs to be at least of 3rd order to

ensure a proper matching for any impedance value of antenna and SAW filter input. The required

component values have to be determined from case to case.

Fig. 1 MLC varistor plus ESD matching Fig. 2 Suppressor diode plus ESD matching

In cases where minor ESD occur, following simplified “ESD matching” topologies can be used

alternatively.

Fig. 3 3rd order high-pass structure for basic ESD protection

In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper

length and width. If this configuration is possible depends on the operating frequency and

available pcb space.

Effectiveness of the applied ESD protection has to be checked according to relevant industry

standards or customer specific requirements

For further information, please refer to EPCOS Application report:

“ESD protection for SAW filters”.

This report can be found under www.epcos.com/rke.Click on “Applications Notes”.

MLC1

Cs1

Lp2

Cs3

to output

matching

Dp1

Lp2

Cs3

Cs1

to output

matching

Lp2

Cs3

Cs1

to output

matching

8May 22, 2013

B3529

1601.50 MHz

Please read

cautions and warnings and

important notes

at the end of this document.

SAW Components

SAW RF filter

Data sheet

References

Type B3529

Ordering code B39162B3529U410

Marking and package C61157-A7-A67

Packaging F61074-V8168-Z000

Date codes L_1126

S-parameters B3529_NB.s2p, B3529_WB.s2p

See file header for port/pin assignment table.

Soldering profile S_6001

RoHS compatible RoHS-compatible means that products are compatible with the

requirements according to Art. 4 (substance restrictions) of Di-

rective 2011/65/EU of the European Parliament and of the

CouncilofJune8th, 2011,ontherestrictionoftheuseofcertain

hazardous substances in electrical and electronic equipment

("Directive")withdueregardtotheapplicationofexemptionsas

per Annex III of the Directive in certain cases.

Matching coils See Inductor pdf-catalog

http://

www

.tdk.co.jp/tefe02/coil.htm#aname1

and Data Library for circuit simulation

http://www.tdk.co.jp/etvcl/index.htm

For further information please contact your local EPCOS sales office or visit our webpage at

ww.epcos.com .

Published by EPCOS AG

Systems, Acoustics, Waves Business Group

P.O. Box 80 17 09, 81617 Munich, GERMANY

EPCOS AG 2013. This brochure replaces the previous edition.

For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or

he international Representatives.

Due to technical requirements components may contain dangerous substances. For information on

he type in question please also contact one of our Sales Offices.

9May 22, 2013

Important notes

he following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical

requirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately

incumbent on the customer to check and decide whether an EPCOS product with the

properties described in the product speciﬁcation is suitable for use in a particular customer

application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as speciﬁed. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained

by third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-speciﬁc notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our

Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more

detailed questions, please contact our sales ofﬁces.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

speciﬁcations. Please check therefore to what extent product descriptions and speciﬁcations

contained in this publication are still applicable before or when you place an order.

We also reserve the right to discontinue production and delivery of products. Conse-

quently, we cannot guarantee that all products named in this publication will always be

available. The aforementioned does not apply in the case of individual agreements deviating

from the foregoing for customer-speciﬁc products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current

version of the “General Terms of Delivery for Products and Services in the Electrical

Industry” published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,

DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,

MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,

SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap

are trademarks registered or pending in Europe and in other countries. Further information