DOCUMENT NUMBER NCD-5DB2-02 SAP-1 Series Single-Mode FC HOUSING TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Sales Dept. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261 JAPAN Telephone : 043-211-1214 -1215 Facsimile : 043-211-8035 SAP-1 Series Single-Mode FC HOUSING TECHNICAL SPECIFICATIONS Document Number NCD-5DB2-02 May 1986 December 1995 July 1996 NAE63D01 " SAP-1 Part " NCD-5DB2-01 NCD-5DB2-02 Copyright 1986, 1995, 1996 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: 310-517-7780 Fax: 310-517-7792 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: 06102-297-0 Fax: 06102-297-211 Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: 852-2421-8611 Fax: 852-2480-5479 Sales Department 5F-1, No.99, Sec. 2, Chung Shan Rd. Taipei 104, Taiwan, R.O.C. Phone: 02-563-5001, 523-5111 Fax: 02-521-9519 Seiko Instruments Singapore pte. Ltd. 2, Marsiling Lane, Woodlands New Town, Singapore, 2573, Singapore Phone: 65-2691370 Fax: 65-2699729 ii TABLE OF CONTENTS Section Page 1. PROVISION 1 1.1 Application Limit 1 2. PARTS NUMBER 1 3. GENERAL SPECIFICATIONS 2 3.1 Parts and Materials 2 3.2 Physical Dimensions 2 3.3 General Tolerances 2 4. PACKING 3 Table Table 1 Parts Number 1 Table 2 Parts and Materials 2 Table 3 General Tolerance 2 Figure Figure 1 Figure 2 to 15 SAP-1 Housing 4 Part Dimensions 5 to 10 iii iv 1. PROVISION 1.1 Application Limit These specifications apply to the SAP-1 Single-Mode FC HOUSING supplied by SII. 2. PARTS NUMBER Parts Number of the Housing is Shown in Table 1. Table 1 Parts Number 1 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the materials are shown in Table 2. Table 2 Parts and materials No. Part Name Q'ty Material Notes Frame 1 Stainless Steel -- Keyring 1 Beryllium Copper -- Washer 1 Phosphor Bronze Spring 1 Stainless Steel Coupling nut 1 Brass Nickel Plating Stopper 1 Brass Nickel Plating Bush 1 Brass Nickel Plating Holder 1 Brass Nickel Plating Nickel Plating -- 1 Hood (for 2.0mm) (1) Synthetic Rubber Hood Color , Hood Marking Shows Table 1 2 Hood (for 2.6mm) (1) Synthetic Rubber Hood Color , Hood Marking Shows Table 1 -3 Hood (for 3.0mm) (1) Synthetic Rubber Hood Color , Hood Marking Shows Table 1 -1 Cap (1) PVC Black -2 Cap (1) Synthetic Rubber with Strings, Black -3 Cap (1) Plastics White 3.2 Physical Dimensions Figure 1 shows the assembled state of SAP-1. Figure 2 to 15 show the part dimension. In accordance with JIS C5970 F01 type connectors 3.3 General Tolerances Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 3. Table 3 General tolerance (JIS B 0405 class m) Basic size step (mm) Over Under Permissible deviation (mm) 0.5 3 0 . 1 3 6 0 . 1 6 30 0 . 2 30 120 0 . 3 2 4. PACKING The product is packed to prevent damage during shippment. 3 note.1: This drawing does not include Caps. Unit: mm Figure 1 SAP-1 HOUSING 4 Unit: mm Figure 2 Frame Unit: mm Figure 3 Keyring Unit: mm Figure 4 Washer 5 Unit: mm Figure 5 Spring Unit: mm Figure 6 Coupling nut Unit: mm Figure 7 Stopper 6 Unit: mm Figure 8 Bush Unit: mm Figure 9 Holder 7 Unit: mm Figure 10 -1 Hood (for 2.0mm) Unit: mm Figure 11 -2 Hood (for 2.6mm) 8 without Marking with making Unit: mm Figure 12 -3 Hood (for 3.0mm) Unit: mm Figure 13 -1 Cap 9 Unit: mm Figure 14 -2 Cap Unit: mm Figure 15 -3 Cap 10