INDUCTORS
MLF1005 1005 [0402 inch]*
MLF1608 1608 [0603 inch]
MLF2012 2012 [0805 inch]
* Dimensions Code JIS[EIA]
September 2014
Inductors for Standard Circuits
Multilayer Ferrite
MLFseries
(2/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
Inductors for Standard Circuits
Multilayer Ferrite
FEATURES
The lineup includes a wide inductance range.
Highly reliable monolithic structure with multilayer integration.
APPLICATION
Smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for modules etc.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
In case the product's inductance is 15µH or higher, both Operating and Storage temperature ranges are –40 to +85°C.
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of the MLF Series
MLF 1005 A R10 △T000
Series name L×W×H Dimensions characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (µH)
1005 1.0×0.5×0.5 A 10N 0.010
(10nH)
J ±5% T Taping 000
1608 1.6×0.8×0.8 C K ±10% A00
2012 2.0×1.25×0.85 D R10 0.1 M ±20% D00
2.0×1.25×1.25 E 1R0 1
G 100 10
K
V
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C）(pieces/reel) （mg）
MLF1005 –55 to +125 –55 to +125 10,000 1.2
MLF1608 –55 to +125 –55 to +125 4,000 4
MLF2012 t=0.85 –55 to +125 –55 to +125 4,000 10
t=1.25 2,000 14
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
Overview of the MLF Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series
MLF1005 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.00±0.05
0.50±0.05 0.50±0.05
0.10min. 0.10min.
Dimensions in mm
0.5
0.5 0.4 0.5
(6/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1005 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " △ " of the Part Number contains the inductance tolerance code, J (±5%) or K (±10%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L Q L, Q measuring
conditions
Self-resonant
frequency(MHz)
DC resistance
(Ω)
Rated current
(mA) Part No.
Frequency
(MHz)
Current
(mA) max.(µH) Tolerance min. typ. min. typ. max. typ.
0.10 ±5%±10% 10 30 25 1.0 450 880 0.51 0.33 180 MLF1005VR10 △T000
0.12 ±5%±10% 10 30 25 1.0 400 800 0.59 0.33 180 MLF1005VR12 △T000
0.15 ±5%±10% 15 30 25 1.0 350 650 0.63 0.39 180 MLF1005VR15 △T000
0.18 ±5%±10% 15 30 25 1.0 320 600 0.72 0.40 160 MLF1005VR18 △T000
0.22 ±5%±10% 15 30 25 1.0 290 450 0.79 0.47 160 MLF1005VR22 △T000
0.27 ±5%±10% 15 30 25 1.0 260 450 0.91 0.65 150 MLF1005VR27 △T000
0.33 ±5%±10% 15 30 25 1.0 230 380 1.05 0.80 140 MLF1005VR33 △T000
0.39 ±5%±10% 15 30 25 1.0 210 330 1.35 0.89 130 MLF1005VR39 △T000
0.47 ±5%±10% 15 30 25 1.0 190 300 1.50 0.95 120 MLF1005VR47 △T000
0.56 ±5%±10% 15 30 25 1.0 170 250 1.95 1.35 120 MLF1005VR56 △T000
0.39 ±5%±10% 30 50 10 1.0 210 600 0.41 0.24 50 MLF1005GR39 △T000
0.47 ±5%±10% 30 55 10 1.0 190 460 0.42 0.25 50 MLF1005GR47 △T000
0.56 ±5%±10% 30 55 10 1.0 170 450 0.47 0.34 45 MLF1005GR56 △T000
0.68 ±5%±10% 30 55 10 1.0 150 360 0.55 0.43 45 MLF1005GR68 △T000
0.82 ±5%±10% 30 60 10 1.0 130 320 0.59 0.43 40 MLF1005GR82 △T000
1.0 ±5%±10% 30 60 10 1.0 120 290 0.64 0.45 40 MLF1005G1R0 △T000
1.2 ±5%±10% 30 60 10 1.0 110 230 0.79 0.55 35 MLF1005G1R2 △T000
1.5 ±5%±10% 30 60 10 1.0 100 200 0.95 0.68 35 MLF1005G1R5 △T000
1.8 ±5%±10% 30 60 10 1.0 90 180 1.05 0.75 30 MLF1005G1R8 △T000
2.2 ±5%±10% 30 60 10 1.0 80 150 1.30 0.99 30 MLF1005G2R2 △T000
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1005 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
10
1
0.1
Frequency(MHz)
Inductance(µH)
G1R8
G1R2
GR82
GR56
GR39
VR47
VR33
VR22
VR15
VR10
1 10 100 1000
0.01
10
1
0.1
Frequency(MHz)
Inductance(µH)
G2R2
G1R5
G1R0
GR68
GR47
VR56
VR39
VR27
VR18
VR12
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(8/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1005 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
70
60
Q
1 10 100 1000
Frequency(MHz)
VR15
G1R2 GR39
VR47
VR10
GR56
GR82G1R8
VR33
VR22
0
10
20
30
40
50
70
60
Q
1 10 100 1000
Frequency(MHz)
GR47
G1R0
G2R2
G1R5
GR68VR56
VR27 VR39
VR12
VR18
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(9/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series
MLF1608 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
1.60±0.15
0.80±0.15 0.80±0.15
0.30±0.20 0.30±0.20
Dimensions in mm
0.8
0.6 0.8 0.6
(10/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1608 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).
The " □ " of the Part Number contains the internal code (000, A00, or D00), following below.
• In case the inductance tolerance code is J: 000
• In case the inductance tolerance code is M or K (L = 0.047 to 8.2µH or 15 to 22µH): A00
• In case the inductance tolerance code is M or K (L = 10,12,27,33µ): D00
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L Q L, Q measuring
conditions
Self-resonant
frequency(MHz)
DC resistance
(Ω)
Rated current
(mA) Part No.
Frequency
(MHz)
Current
(mA) max.(µH) Tolerance min. typ. min. typ. max. typ.
0.047 ±20% 10 20 50 1.0 600 900 0.20 0.10 200 MLF1608D47N △T□□□
0.068 ±20% 10 20 50 1.0 550 700 0.30 0.15 200 MLF1608D68N △T□□□
0.082 ±20% 10 20 50 1.0 500 650 0.30 0.15 200 MLF1608D82N △T□□□
0.10 ±5%±10%±20% 15 25 25 1.0 450 600 0.35 0.20 200 MLF1608DR10 △T□□□
0.12 ±5%±10%±20% 15 25 25 1.0 400 550 0.40 0.20 200 MLF1608DR12 △T□□□
0.15 ±5%±10%±20% 15 25 25 1.0 350 500 0.45 0.25 200 MLF1608DR15 △T□□□
0.18 ±5%±10%±20% 15 25 25 1.0 320 450 0.50 0.25 150 MLF1608DR18 △T□□□
0.22 ±5%±10%±20% 15 25 25 1.0 290 400 0.55 0.30 150 MLF1608DR22 △T□□□
0.27 ±5%±10%±20% 15 25 25 1.0 260 350 0.60 0.35 150 MLF1608DR27 △T□□□
0.33 ±5%±10%±20% 15 25 25 1.0 230 320 0.75 0.40 100 MLF1608DR33 △T□□□
0.39 ±5%±10%±20% 15 25 25 1.0 210 290 0.85 0.45 100 MLF1608DR39 △T□□□
0.47 ±5%±10%±20% 15 30 25 1.0 190 260 0.95 0.50 100 MLF1608DR47 △T□□□
0.56 ±5%±10%±20% 15 30 25 1.0 170 230 1.05 0.55 100 MLF1608DR56 △T□□□
0.68 ±5%±10%±20% 15 30 25 1.0 150 210 1.25 0.65 70 MLF1608DR68 △T□□□
0.82 ±5%±10%±20% 15 30 25 1.0 130 190 1.40 0.75 70 MLF1608DR82 △T□□□
1.0 ±5%±10%±20% 35 50 10 1.0 120 170 0.50 0.25 50 MLF1608A1R0 △T□□□
1.2 ±5%±10%±20% 35 50 10 1.0 110 150 0.65 0.25 50 MLF1608A1R2 △T□□□
1.5 ±5%±10%±20% 35 55 10 1.0 100 140 0.70 0.30 50 MLF1608A1R5 △T□□□
1.8 ±5%±10%±20% 35 55 10 1.0 90 130 0.85 0.35 50 MLF1608A1R8 △T□□□
2.2 ±5%±10%±20% 35 55 10 1.0 80 120 1.00 0.45 30 MLF1608A2R2 △T□□□
2.7 ±5%±10%±20% 35 55 10 1.0 70 110 1.15 0.50 30 MLF1608A2R7 △T□□□
3.3 ±5%±10%±20% 35 60 10 1.0 65 100 1.30 0.55 30 MLF1608A3R3 △T□□□
3.9 ±5%±10%±20% 35 60 10 1.0 60 90 1.45 0.65 30 MLF1608A3R9 △T□□□
4.7 ±5%±10%±20% 35 60 10 1.0 55 80 1.60 0.75 30 MLF1608A4R7 △T□□□
5.6 ±5%±10%±20% 35 60 4 0.1 45 70 1.10 0.55 15 MLF1608E5R6 △T□□□
6.8 ±5%±10%±20% 35 60 40.1 40 60 1.30 0.65 15 MLF1608E6R8 △T□□□
8.2 ±5%±10%±20% 35 60 4 0.1 35 55 1.50 0.80 10 MLF1608E8R2 △T□□□
10 ±5%±10%±20% 30 55 20.1 30 50 1.70 1.00 10 MLF1608E100 △T□□□
12 ±5%±10%±20% 30 55 2 0.1 25 45 1.80 1.20 10 MLF1608E120 △T□□□
15 ±10%±20% 20 40 10.1 22 42 1.50 0.80 2MLF1608C150 △T□□□
18 ±10%±20% 20 40 1 0.1 20 40 1.60 0.85 2 MLF1608C180 △T□□□
22 ±10%±20% 20 40 10.1 18 38 1.70 0.90 2MLF1608C220 △T□□□
27 ±10%±20% 20 40 1 0.1 15 35 1.80 1.20 2 MLF1608C270 △T□□□
33 ±10%±20% 20 40 10.1 10 30 2.20 1.40 2MLF1608C330 △T□□□
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(11/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(µH)
E100
DR68
DR47
DR33
DR22
DR15
DR10
E6R8
A4R7
A3R3
A2R2
A1R5
A1R0
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(µH)
E120
E8R2
E5R6 A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(12/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1608 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1 101 100
0.1
100
10
1
Frequency(MHz)
Inductance(µH)
C330
C270
C220
C180C150
Product No. Manufacturer
4294A+16034G Agilent Technologies
(13/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1608 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
70
60
Q
1 10 100 1000
Frequency(MHz)
E100 E6R8
A1R0
DR68
DR33
DR15
DR10
A3R3
A2R2
A1R5
DR47
DR22
0
10
20
30
40
50
70
60
Q
110 1000100
Frequency(MHz)
E120
E8R2
E5R6
A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(14/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF1608 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
70
60
Q
0.1 1 10 100
Frequency(MHz)
C270
C220
C180
C330
C150
Product No. Manufacturer
4294A+16034G Agilent Technologies
(15/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series
MLF2012 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
2.00±0.20
T 1.25±0.20
0.50±0.30 0.50±0.30
T
0.85±0.20
1.25±0.20
Dimensions in mm
1.2
0.8 1.0 0.8
(16/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L Q L, Q measuring
conditions
Self-resonant
frequency
(MHz)
DC resistance
(Ω)
Rated
current
(mA)
Thickness
T
(mm)
Part No.
(µH) Tolerance min. typ. Frequency
(MHz)
Current
(mA) min. typ. max. typ. max.
0.047 ±20% 15 25 50 1.0 550 700 0.10 0.05 300 0.85 MLF2012D47N △T000
0.068 ±20% 15 25 50 1.0 500 600 0.15 0.08 300 0.85 MLF2012D68N △T000
0.082 ±20% 15 25 50 1.0 450 550 0.15 0.08 300 0.85 MLF2012D82N △T000
0.10 ±5%±10%±20% 20 30 25 1.0 400 500 0.10 0.10 300 0.85 MLF2012DR10 △T000
0.12 ±5%±10%±20% 20 30 25 1.0 360 450 0.12 0.20 300 0.85 MLF2012DR12 △T000
0.15 ±5%±10%±20% 20 30 25 1.0 320 410 0.13 0.20 300 0.85 MLF2012DR15 △T000
0.18 ±5%±10%±20% 20 30 25 1.0 280 370 0.15 0.20 300 0.85 MLF2012DR18 △T000
0.22 ±5%±10%±20% 20 30 25 1.0 250 330 0.16 0.30 250 0.85 MLF2012DR22 △T000
0.27 ±5%±10%±20% 20 30 25 1.0 220 300 0.18 0.30 250 0.85 MLF2012DR27 △T000
0.33 ±5%±10%±20% 20 30 25 1.0 200 270 0.23 0.40 250 0.85 MLF2012DR33 △T000
0.39 ±5%±10%±20% 25 35 25 1.0 180 250 0.25 0.40 200 0.85 MLF2012DR39 △T000
0.47 ±5%±10%±20% 25 35 25 1.0 160 230 0.25 0.50 200 1.25 MLF2012DR47 △T000
0.56 ±5%±10%±20% 25 35 25 1.0 150 210 0.30 0.50 150 1.25 MLF2012DR56 △T000
0.68 ±5%±10%±20% 25 35 25 1.0 140 190 0.35 0.60 150 1.25 MLF2012DR68 △T000
0.82 ±5%±10%±20% 25 35 25 1.0 130 170 0.40 0.60 150 1.25 MLF2012DR82 △T000
1.0 ±5%±10%±20% 45 55 10 1.0 120 160 0.15 0.30 80 0.85 MLF2012A1R0 △T000
1.2 ±5%±10%±20% 45 55 10 1.0 110 150 0.15 0.30 80 0.85 MLF2012A1R2 △T000
1.5 ±5%±10%±20% 45 60 10 1.0 100 140 0.18 0.40 80 0.85 MLF2012A1R5 △T000
1.8 ±5%±10%±20% 45 60 10 1.0 90 130 0.20 0.40 80 0.85 MLF2012A1R8 △T000
2.2 ±5%±10%±20% 45 60 10 1.0 80 120 0.22 0.50 50 0.85 MLF2012A2R2 △T000
2.7 ±5%±10%±20% 45 70 10 1.0 70 100 0.25 0.50 50 1.25 MLF2012A2R7 △T000
3.3 ±5%±10%±20% 45 70 10 1.0 60 90 0.28 0.60 50 1.25 MLF2012A3R3 △T000
3.9 ±5%±10%±20% 45 70 10 1.0 55 80 0.30 0.60 30 1.25 MLF2012A3R9 △T000
4.7 ±5%±10%±20% 45 70 10 1.0 50 70 0.35 0.70 30 1.25 MLF2012A4R7 △T000
5.6 ±5%±10%±20% 50 75 4 0.1 45 65 0.60 0.30 15 1.25 MLF2012E5R6 △T000
6.8 ±5%±10%±20% 50 75 40.1 40 60 0.65 0.32 15 1.25 MLF2012E6R8 △T000
8.2 ±5%±10%±20% 50 75 4 0.1 35 55 0.70 0.35 15 1.25 MLF2012E8R2 △T000
10 ±5%±10%±20% 50 75 20.1 30 50 0.80 0.40 15 1.25 MLF2012E100 △T000
12 ±5%±10%±20% 50 75 2 0.1 25 45 0.90 0.50 15 1.25 MLF2012E120 △T000
15 ±10%±20% 30 45 10.1 22 40 0.70 0.35 51.25 MLF2012C150 △T000
18 ±10%±20% 30 45 1 0.1 20 38 0.80 0.38 5 1.25 MLF2012C180 △T000
22 ±10%±20% 30 45 10.1 18 35 0.90 0.45 51.25 MLF2012C220 △T000
27 ±10%±20% 30 45 1 0.1 17 33 1.00 0.50 5 1.25 MLF2012C270 △T000
33 ±10%±20% 30 45 0.4 0.1 15 28 1.10 0.55 51.25 MLF2012C330 △T000
39 ±10%±20% 35 55 2 0.1 13 23 2.40 1.30 4 1.25 MLF2012K390 △T000
47 ±10%±20% 35 55 20.1 11 20 2.70 1.60 41.25 MLF2012K470 △T000
56 ±10%±20% 35 55 2 0.1 10 18 2.80 1.80 4 1.25 MLF2012K560 △T000
68 ±10%±20% 25 45 10.1 916 2.90 2.00 21.25 MLF2012C680 △T000
82 ±10%±20% 25 45 1 0.1 8 14 3.00 2.40 2 1.25 MLF2012C820 △T000
100 ±10%±20% 25 45 10.1 712 3.10 2.50 21.25 MLF2012C101 △T000
Measurement item Product No. Manufacturer
L, Q 4294A+16034G Agilent Technologies
Self-resonant frequency E4991A Agilent Technologies
DC resistance Type-7561 Yokogawa
(17/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(µH)
E100
DR68
DR47
DR33
DR22
DR15
DR10
E6R8A4R7
A3R3
A2R2
A1R5
A1R0
1 10 100 1000
0.01
100
10
1
0.1
Frequency(MHz)
Inductance(µH)
E120
E8R2
E5R6 A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(18/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0.1 101 100
0.1
100
10
1
Frequency(MHz)
Inductance(µH)
C101
C820 K560
K470
K390
C270
C220
C180
C150
C680
C330
Product No. Manufacturer
4294A+16034G Agilent Technologies
(19/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF2012 Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
90
70
80
60
Q
110 1000100
Frequency(MHz)
E100
E6R8
A1R0
DR33
DR15
DR10
A3R3
A2R2
A1R5
DR47
DR22
DR68
A4R7
0
10
20
30
40
50
90
80
70
60
Q
110 1000100
Frequency(MHz)
E120
E8R2
E5R6 A3R9
A2R7
A1R8
DR82
DR56
DR39
DR27
DR18
DR12
A1R2
Product No. Manufacturer
E4991A+16192A Agilent Technologies
(20/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series MLF2012 Type
Q FREQUENCY CHARACTERISTICS GRAPH
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
10
20
30
40
50
90
80
70
60
Q
0.1 10 1001
Frequency(MHz)
C101
C820
C680
K560
K470
K390
C330C270
C220
C180
C150
Product No. Manufacturer
4294A+16034G Agilent Technologies
(21/21)
INDUCTORS
20140903 / inductor_commercial_standard_mlf_en.fm
• All specifications are subject to change without notice.
MLF series
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm
Typ e A B K
MLF1005 1.15±0.1 0.65±0.1 0.8 max.
MLF1608 1.9±0.2 1.1±0.2 1.1 max.
MLF2012 t=0.85 2.3±0.2 1.5±0.2 1.1 max.
t=1.25 2.3±0.2 1.5±0.2 1.5 max.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TDK:
MLF1608A1R8K MLF1608A2R2K MLF1608A3R3K MLF1608A4R7K MLF1608C150K MLF1608C180K
MLF1608C270K MLF1608D47NM MLF1608DR10K MLF1608DR18K MLF1608DR22K MLF1608DR33K
MLF1608DR39K MLF1608DR47K MLF1608DR68K MLF1608E8R2K MLF2012A1R0K MLF2012A1R5K
MLF2012A1R8K MLF2012A2R7K MLF2012A3R3K MLF2012A3R9K MLF2012C150K MLF2012C180K
MLF2012D47NM MLF2012DR12K MLF2012DR18K MLF2012DR27K MLF2012DR33K MLF2012DR47K
MLF2012DR68K MLF2012E120K MLF2012E5R6K MLF2012E6R8K MLF2012E8R2K MLF2012K390K
MLF2012K470K MLF1005DR27KT MLF1005AR56KT MLF1005AR82KT MLF1005A1R0KT MLF1005DR10KT
MLF1005A2R2KT MLF1005A1R2KT MLF1005DR12KT MLF1005AR39KT MLF1005DR18KT MLF1005AR47KT
MLF1005DR33KT MLF1608DR10M MLF1608DR15M MLF1608DR56M MLF2012A1R8M MLF2012A4R7M
MLF2012C330M MLF1005LR10K MLF1005LR12K MLF1005LR15K MLF1005LR18K MLF1005LR22K
MLF1005LR27K MLF1005LR33K MLF1005LR39K MLF1005LR47K MLF1005LR56K MLF1005LR68K
MLF1005LR82K MLF1005L1R0K MLF1005L1R2K MLF1005L1R5K MLF1005L1R8K MLF1005L2R2K
MLF2012DR82KT MLF1005GR39KT000 MLF1005AR68KT MLF1005A1R5KT MLF1005DR22K MLF1005A1R8K
MLF2012A4R7JT000 MLF2012C270KT000 MLF2012K560KT000 MLF1005VR22JT000 MLF1608DR39JT000
MLF2012E5R6JT000 MLF1005VR56JT000 MLF1608E5R6KTA00 MLF1608C220KTA00 MLF2012D82NMT000
MLF1005G1R5KT000 MLF1005G2R2JT000 MLF1005GR56KT000 MLF2012DR12KT000 MLF1005GR82JT000
MLF2012DR22JT000 MLF1608A1R5JT000 MLF2012DR56JT000 MLF2012DR18JT000 MLF1608A3R9JT000
MLF1608DR15JT000 MLF1005G1R0KT000
