Order this document by MC33411A/D MC33411A/B Advance Information 900 MHz Analog Cordless Phone Baseband with Compander The MC33411 900 MHz Analog Cordless Phone Baseband system is designed to fit the requirements of a 900 MHz analog cordless telephone system. Included are three PLLs (Phase-Locked Loops). Two are intended for use with external VCOs and 64/65 or 128/129 dual modulus prescalers, and can control the transmit and receive (LO1) frequencies for 900 MHz communication. The third PLL is configured as the 2nd local oscillator (LO2), and is functional to 80 MHz. Also included are muting, audio gain adjust (internal and external), low battery/carrier detect, and a wide range for the PLL reference frequency. The power supply range is 2.7 to 5.5 V. "A" version devices have programmable MCU clock out and reference oscillator disable functions, whereas these functions are always enabled for "B" version devices. * * * * * * * * * * * * 900 MHz ANALOG CORDLESS PHONE BASEBAND WITH COMPANDER SEMICONDUCTOR TECHNICAL DATA Complete Expander/Compressor for Superior Noise Rejection Two PLLs and a LO Suitable for a 900 MHz System FTA SUFFIX PLASTIC PACKAGE CASE 932 (LQFP-48) Minimal External Components Transmit Path Includes Adjustable Gain Amplifier, Filters, Mute, Compressor with Bypass and Limiter Receive Path Contains Data Slicer, Adjustable Gain Amplifier, Sidetone Attenuator, Filters, Expander with Bypass, Mute, Volume Control and Power Amplifier Dual A/Ds are Provided to Monitor RSSI and VCC ORDERING INFORMATION Device Independent Power Amplifier with Differential Outputs and Mute MC33411AFTA Selectable Frequency for Switched Capacitor Filters, PLLs and the LO MC33411BFTA Operating Temperature Package TA = -20 to 70C LQFP-48 Reference Frequency Source can be a Crystal or System Clock Serial P Port to Control Gain, Mute, Frequency Selection, Phase Detector Gain, Power Down Modes, Low Battery Detect and Others Power Supply Range: 2.7 to 5.5 V Power Down Modes for Power Conservation Simplified Block Diagram DS In VCC RSSI Tx In Rx Out Data Slicer DS Out Dual A/D Amp/Mute Compressor Filter Gain Adj Tx Out Filter Sidetone Attn Mute Expander Power Amp Audio In MCU Clock Clock Enable Data MCU Interface Programmable Counters PLL #1 PLL #2 2nd LO Tank LO2 Out This device contains 11,108 active transistors. LPF+ VCO + Prescaler LPF+ VCO + Prescaler This document contains information on a new product. Specifications and information herein are subject to change without notice. MOTOROLA RF/IF DEVICE DATA LPF Motorola, Inc. 1998 Rev 1 1 MC33411A/B Figure 1. Test Circuit VCC 1.0 1.0 1.0 1.0 0.1 130 4.99 k 4.99 k VCC Tx Audio 1.0 0.47 Rx E In Out 36 Ecap 35 E Out 33 34 Gnd PA PAO- PAI 32 31 30 VCC PA PAO+ 28 29 4.7 VB 27 47.5 k 0.1 VAG MCI 26 25 47.5 k Rx Mute 1.0 k RSSI In 1.0 Vol Ctl Expander 37 Mic Amp Power Amp Power Amp Mute Exp PT 24 Comp PT Rx Audio In 38 1.0 DS In VCC Attn AALPF Gnd Audio 39 40 49.9 LO2 Out VCC LO2 VCC 1.0 0.001 LO2+ VCC 6b A/D Converter VCC Audio 41 SPI LO2 Ctl LO2- LO2PD LO2 Gnd VCC Audio VCC 10 0.1 C In 1.0 VCC Ccap 0.47 1.0 C Out 1.0 19 Lim In Tx Gain Adj 18 43 Limiter 2nd LO VCO 44 Inverter 45 47 48 SPI 16 14b Ctr Divide By 2 SCF Clk 46 LO2 Phase Detect 13b N' 15 14 1 13b N Rx Phase Detect 2 3 FRx MC FRx 4 PLL VCC VCC 0.01 RF In 0.001 5 Rx PD 7b A 6 PLL Gnd 7 Tx PD MCU Clk Ctr MCU Interface Mod Ctl Tx Phase Detect 8 PLL VCC 9 FTx 1.0 10 k DS Out Fref Out 0.1 6b SCF Clk Ctr 12b Ref Ctr 7b A' Tx Out Tx Mute LPF 17 Mod Ctl 2 20 42 100 p LO2 Gnd 21 Low Max Gain Side Tone Attn SPI Data Slicer 5.6 p 22 SPI 0.1 5.62 k Compressor SPI RSSI 6b A/D Converter BG Vref 23 ALC Rx Gain Adj LPF MCO VB 10 FTx MC EN 11 Fref In Gnd Digital 13 MCU Clk Out SPI 12 CLK Data VCC 1.0 1.0 0.001 49.9 0.01 RF In 49.9 MOTOROLA RF/IF DEVICE DATA MC33411A/B MAXIMUM RATINGS Symbol Value Unit Power Supply Voltage Rating VCC -0.5 to 6.0 V Junction Temperature TJ -6.5 to 150 C Maximum Power Dissipation PD 150 mW NOTES: 1. Meets Human Body Model (HBM) 2000 V and Machine Model (MM) 200 V. 2. ESD data available upon request. RECOMMENDED OPERATING CONDITIONS Characteristic Symbol Min Typ Max Unit VCC 2.7 3.6 5.5 Vdc Operating Ambient Temperature TA -20 - 70 C Input Voltage Low (Data, CLK, EN) Vil - - 0.3 V Input Voltage High (Data, CLK, EN) Vih Tx PLL VCC - 0.3 - - V Frange 4.0 - 18.25 MHz VB - 1.5 - V Supply Voltage Frequency Range (Fref in) Bandgap Reference Voltage DC ELECTRICAL CHARACTERISTICS (VCC = 3.6 V, TA = 25C, unless otherwise noted.) Characteristic Static Current Active Mode (R5/8 to 0 = 0; R6/7 = 0) Receive Mode (R5/8, 7, 3, 2, 0 = 0; R6/7 = 0; R5/6,5,4,1 = 1) Standby Mode (R5/0 = 0; R6/7 = 0; R5/8 to 1 = 1) Inactive Mode, A only (R5/8 to 0 =1; R6/7 = 1) Data Slicer Only RSSI/Batt A/D Only Tx Audio Only Rx Audio Only PA Only 2nd LO/Fref Only Rx PLL/Fref Only Tx PLL/Fref Only Ref Osc Only, "A" version only Symbol Min Typ Max Unit ACT ICC Rx ICC STD ICC INA ICC DS ICC AD ICC TxA ICC RxA ICC PA ICC 2LO ICC RxPLL ICC TxPLL ICC ROSC ICC - - - - - - - - - - - - - 15 10 500 10 100 70 1.4 1.4 1.0 6.0 1.0 1.0 500 20 13 1500 15 - - - - - - - - - mA mA A A A A mA mA mA mA mA mA A VB 1.38 1.5 1.62 V Reference Voltage, Unadjusted ELECTRICAL CHARACTERISTICS (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Characteristics Input Pin Measure Pin Symbol Min Typ Max Unit Rx Audio In E Out G -4.0 0 4.0 dB E In E Out Gt Rx AUDIO PATH Absolute Gain (Vin = -20 dBV) Gain Tracking (Referenced to Eout for Vin = -20 dBV) Vin = -30 dBV Vin = -40 dBV Total Harmonic Distortion (Vin = -20 dBV) Rx Audio In Maximum Input Voltage (VCC = 2.7 V) Rx Audio In Maximum Output Voltage (Increase input voltage until output voltage THD = 5%, then measure output voltage) E In PAO- E Out THD VOmax dB -21 -42 -20 -40 -19 -38 - 0.7 1.0 % - -11.5 - dBV -2.0 0 - dBV NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. MOTOROLA RF/IF DEVICE DATA 3 MC33411A/B ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Characteristics Input Pin Measure Pin Symbol Min Typ Max - - 600 7.5 - - Unit Rx AUDIO PATH (continued) Input Impedance Zin RxAudio In E In k Attack Time Ecap = 0.5 F, Rfilt = 40 k E In E Out ta - 3.0 - mS Release Time Ecap = 0.5 F, Rfilt = 40 k E In E Out tr - 13.5 - mS Compressor to Expander Crosstalk (Vin = -10 dBV, VE In = AC Gnd) MCI E Out CT - -90 -60 dB Rx Muting (Vin = -20 dBV, Rx Gain Adj = 01111) Rx Audio In E Out Me - -84 -60 dB Rx High Frequency Corner (Vin = -20 dBV) SCF Counter = 31d Rx Audio In Rx Out Rx fch 3.6 3.8 4.0 kHz Low Pass Filter Passband Ripple (Vin = -20 dBV) Rx Audio In Rx Out Ripple - 0.4 0.6 dB Rx Gain Adjust Range Rx Audio In Rx Out Rx Range - -9.0 to 10 - dB Rx Gain Adjust Steps Rx Audio In Rx Out Rx n - 20 - Audio Path Noise, C-Message Weighting (Vin = AC Gnd) Rx Audio In EN Rx Out E Out PA Out Volume Control Adjust Range Volume Control Levels Side Tone Attenuate Selections dBV - - - -85 <-95 <-95 - - - Rx Audio In E Out VCtlRange - -14 to 16 - E In E Out Vcn - 16 - Rx Audio In Rx Out STAn - 4 - E Out STA - - - - 0.0 1.5 3.0 5.2 - - - - - -3.0 - dB Side Tone Attenuate (Referenced to E In) Selection = 00 Selection = 01 Selection = 10 Selection = 11 Side Tone Attenuate Threshold (C Out/E In) STAthr dB dB POWER AMP/MUTE (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, fin = 1.0 kHz) Output Swing, 5.0 mA load (VPAO+ @ -5.0 mA - VPAO+@ 5.0 mA) PAI PAO+ VOmax 1.3 2.4 - Vpp Output Swing, 5.0 mA load (VPAO- @ -5.0 mA - VPAO-@ 5.0 mA) PAI PAO- VOmax 1.3 2.4 - Vpp Output Swing, No Load PAI PAO+ VOmax - 2.7 - Vpp Output Swing, No Load PAI PAO- VOmax - 2.7 - Vpp PAO-, PAO+ IOmax - 5.0 - mA PAO- Msp - -92 -60 dB MCO AVOL - 100.000 - V/V Maximum Output Current Power Amp Mute (Vin = -20 dBV, RL = 130 ) PAI MIC AMP (VCC = 3.6 V, TA = 25C, Active Mode, fin = 1.0 kHz) Open Loop Gain MCI Gain Bandwidth MCI MCO GBW - 100 - kHz Maximum Output Swing (RL = 10 k) MCI MCO VOmax - 3.2 - Vpp NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. 4 MOTOROLA RF/IF DEVICE DATA MC33411A/B ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Characteristics Input Pin Measure Pin Symbol Min Typ Tx AUDIO PATH (VCC = 3.6 V, Limiter, Mutes, ALC disabled, TA = 25C, Gain = 1, Active Mode, fin = 1.0 kHz) Absolute Gain (Vin = -10 dBV) MCI TX Out G -4.0 0 Gain Tracking (Referenced to Tx Out for Vin = -10 dBV) Vin = -30 dBV Vin = -40 dBV MCI Total Harmonic Distortion (Vin = -10 dBV) MCI Tx Out Maximum Output Voltage (Increase input voltage until output voltage THD = 5%, then measure output voltage. Tx Gain Adj = 8.0 dB) MCI Input Impedance Tx Out Max Unit 4.0 dB Gt dB -11 -17 -10 -15 -9.0 -13 THD - 0.5 1.2 % Tx Out VOmax -8.0 -5.0 - dBV C In Zin - 10 - k Attack Time Ccap = 0.5 F, Rfilt = 40 k C In Tx Out ta - 3.0 - mS Release Time Ccap = 0.5 F, Rfilt = 40 k C In Tx Out tr - 13.5 - mS Expander to Compressor Crosstalk (Vin = -20 dBV, PA no load, VCin = AC Gnd) E In Tx Out CT - -60 -40 dB Tx Muting (Vin = -10 dBV) MCI Tx Out Mc - -88 -60 dB ALC Output Level (When Enabled) Vin = -10 dBV Vin = -2.5 dBV MCI Tx Out ALCout -15 -13 -13 -11 -8.0 -6.0 ALC Slope (When Enabled) Vin = -10 dBV Vin = -2.5 dBV MCI Tx Out Slope 0.1 0.25 0.4 dB/dB ALC Input Dynamic Range C In Tx Out DR - -16 to -2.5 - dBV Limiter Output Level (When Enabled, Vin = -2.5 dBV) Lim In Tx Out Vlim -10 -7.0 - dBV Tx High Frequency Corner (Vin = -10 dBV, Unity Gain) SCF Counter = 31d Lim In Tx Out Tx fch 3.45 3.65 3.85 kHz Low Pass Filter Passband Ripple (Vin = -10 dBV) Lim In Tx Out Ripple - 0.4 1.0 dB MCU Clock or SCF Spurs (Vin = -10 dBv, relative to SCF or MCU Fundamental) Lim In Tx Out - - -25 - dBc MCI Tx Out AVmax - - 21 12 - - Maximum Compressor Gain (Vin = -70 dBV) R6/8 = 0 R6/8 = 1 dBV dB Tx Gain Adjust Range Lim In Tx Out Tx Range - -9.0 to 10 - Tx Gain Adjust Steps Lim In Tx Out Tx N - 20 - dB DATA AMP COMPARATOR (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active or Receive Mode) Hysteresis DS In DS Out Hys 20 42 60 mV Threshold Voltage DS In DS Out VT - VCC - 0.7 - V DS In Zin 200 250 280 k DS Out Zout - 100 - k Input Impedance Output Impedance Output High Voltage (Vin = VCC - 1.0 V, Ioh = 0 mA) DS In DS Out Voh VCC Audio - 0.1 VCC Audio - V Output Low Voltage (Vin = VCC - 0.4 V, Iol = 0 mA) DS In DS Out Vol - 0.1 0.4 V Maximum Frequency DS In DS Out Fmax - 10 - kHz NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. MOTOROLA RF/IF DEVICE DATA 5 MC33411A/B ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Characteristics Input Pin Measure Pin Symbol Min Typ Max Unit RSSI/LOW BATTERY A/D (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active or Receive Mode) RSSI Voltage Range RSSI In SPI RSSI Range V Minimum (R5/17-12 = 0) Interim (R5/17-12 = 100000) Maximum (R5/17-12 = 1) Low Battery Detect Operating Range - .744 - VCC Audio SPI 0 - 1.6 - .792 - LOWB Range V Minimum Interim (R5/23-18 = 101111) Maximum (R5/23-18 = 1) - 2.7 - 2.7 - 3.75 - 3.1 - Differential Non-linearity RSSI In/ VCC Audio SPI A/D DNL -1.0 0.5 1.0 LSB Resolution RSSI In/ VCC Audio SPI Resolution - 6 - Bits RSSI In Iin -80 20 80 nA Input Current REFERENCE FREQUENCY (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode) Input Current High (Vin = VCC) Fref in Iih 2.0 5.0 15 A Input Current Low (Vin = 0 V) Fref in Iil -15 -5.0 -2.0 A Fref out Vin 300 - - mVpp - Minimum Input Voltage Fref In Fref in Input Impedance Output Impedance Fref in Zin - 2.9 pF||11.6 k Fref out Zout - 2.5 pF||4.5 k - MICROPROCESSOR INTERFACE (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active or Receive Mode) Input Low Voltage Data/EN /CLK Vil 0 - 0.3 V Input High Voltage Data/EN /CLK Vih Tx PLL VCC - 0.3 - Tx PLL VCC V Input Current Low (Vin = 0.3 V, Standby Mode) Data, EN, CLK Data, EN, CLK Iil -5.0 0.4 - A Input Current High (Vin = 3.3 V, Standby Mode) Data, EN, CLK Data, EN, CLK Iih - 1.6 5.0 A Hysteresis Voltage Data, EN, CLK Data, EN, CLK Vhys - 1.0 - V Fmax 2.0 - - MHz Data, CLK, EN Cin - 8.0 - pF EN, CLK tsuEC - 200 - nS Data to CLK Setup Time Data, CLK tsuDC - 100 - nS Hold Time Data, CLK th - 90 - nS Recovery Time EN, CLK trec - 90 - nS Input Pulse Width EN, CLK tw - 100 - nS tpuMCU - 100 - S Voh Tx PLL VCC - 0.3 3.5 - V Maximum Clock Frequency Input Capacitance Data, EN, CLK EN to CLK Setup Time CLK MCU Interface Power-Up Delay Output High Voltage (Ioh = 0 mA) MCU Clk Out NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. 6 MOTOROLA RF/IF DEVICE DATA MC33411A/B ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Characteristics Input Pin Measure Pin Symbol Min Typ Max Unit MICROPROCESSOR INTERFACE (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active or Receive Mode) Output Low Voltage (Iol = 0 mA) MCU Clk Out Vol - 0.1 0.3 V Output High Voltage (Ioh = 0 mA) Data Voh Tx PLL VCC - 0.3 3.5 - V Output Low Voltage (Iol = 0 mA) Data Vol - 0.1 0.3 V Rx/Tx PLL CHARACTERISTICS (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active or Receive Mode) Output Source Current (VPD = 0.5 V or VCC - 0.5 V) 100 A mode 400 A mode Rx PD & Tx PD Output Sink Current (VPD = 0.5 V or VCC - 0.5 V) 100 A mode 400 A mode Rx PD & Tx PD A Ioh -130 -520 -100 -400 -70 -280 70 280 100 400 130 520 A Iol Current Match, 100 A mode or 400 A mode, VPD = VCC / 2 (i.e., 100 x (ABS (Ioh / Iol ))) Rx PD Tx PD Match 80 100 125 % Output Off Current (VPD = VCC /2),100 A mode or 400 A mode Rx PD Tx PD Ioz -80 5.0 80 nA Input Current Low (Vin = 0 V) FRx FTx Iil -10 -7.5 - A Input Current High (Vin = VCC) FRx FTx Iih - 10 14 A Input Bias Voltage FRx FTx Vbias - 1.5 - V Output Voltage High (Ioh = 0 mA, Voltage Mode) FRxMC Voh - Rx PLL VCC - 0.1 - V Output Voltage High (Ioh = 0 mA, Voltage Mode) FTxMC Voh - Tx PLL VCC - 0.1 - V Output Voltage Low (Iol = 0 mA, Voltage Mode) FRxMC FTxMC Vol - 0.1 - V Output Current High (Voh = 0.8 V, Current Mode) FRxMC FTxMC Ioh -130 -100 -70 A Output Current Low (Vol = 0.8 V, Current Mode) FRxMC FTxMC Iol 70 100 130 A Maximum Input Frequency FRx FTx Fmax 20 - - MHz Input Voltage Swing FRx FTx Vin 200 - 1200 mVpp FRxMC FTxMC - - 20 - nS Modulus Control Prop Delay FRx FTx LO2 PLL CHARACTERISTICS (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode) Output Source Current (VPD = 0.5 V or VCC - 0.5 V) 100 A mode 400 A mode LO2PD Output Sink Current (VPD = 0.5 V or VCC - 0.5 V) 100 A mode 400 A mode LO2PD Current Match, 100 A mode or 400 A mode, VPD = VCC / 2 (i.e., 100 x (ABS (Ioh / Iol ))) LO2PD A Ioh -130 -520 -100 -400 -70 -280 70 280 100 400 130 520 80 100 125 A Iol Match % NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. MOTOROLA RF/IF DEVICE DATA 7 MC33411A/B ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode, Rx Gain = 01111, Vol Adj = 0111, fin = 1.0 kHz, unless otherwise noted.) Input Pin Characteristics Measure Pin Symbol Min Typ Max Unit LO2 PLL CHARACTERISTICS (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode) Output Off Current (VPD = VCC /2) LO2PD Ioz -80 5.0 80 nA Input Current Low (Vin = 0.5 V) LO2Ctl Iil -1.0 -0.02 - A Input Current High (Vin = VCC - 0.5 V) LO2Ctl Iih - 0.02 1.0 A Input Voltage Range LO2Ctl Vrange 0.4 - VCC V 65 80 - MHz 112 180 245 mVpp 12-Bit Reference Counter Range [Note 1] - 3 to 4095 - 13-Bit N Counter Range [Note 1] - 3 to 8191 - 7-Bit A Counter Range [Note 1] 64/65 Modulus Prescaler 128/129 Modulus Prescaler - - 0 to 63 0 to 127 - - 14-Bit LO2 Counter Range [Note 1] - 12 to 16383 - 6-Bit Counters (for SCF) [Note 1] - 3 to 63 - Maximum 2nd LO Frequency LO2 Out Drive (25 load) Vout COUNTERS (VCC = 3.6 V, VB = 1.5 V, TA = 25C, Active Mode) NOTES: 1. Values specified are pure numbers to the base 10. 2. Typical performance parameters indicate the potential of the device under ideal operating conditions. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA PIN FUNCTION DESCRIPTION Pin Symbol/Type 1 FRx MC (Output) Description Description Modulus Control Output for the Rx PLL section. Can be set to output in current mode or voltage mode, selectable with bit 3/16. Rx PLL VCC 100 A Current Mode 1 FRx MC Rx PLL VCC 100 A Voltage Mode 2 FRx (Input) Receives the signal from the external 64/65 or 128/129 prescaler. DC bias is at 1.3 V. PLL VCC 2 200 k Bias FRx 80 A NOTE: 8 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 3 Rx PLL VCC (Input) Description 10 3 Description 0.01 10 VCC Rx PLL Section 4 Rx PD (Output) Rx PLL VCC 100/ 400 A 125 4 to Filter Rx PD Rx PLL VCC Supply pin for the Rx PLL section. Allowable range is 2.7 to 5.5 V and must be within 0.5 V of all other VCC pins. Good bypassing is required and isolation with a 10 resistor is recommended. Rx Phase Detector Output. The output either sources or sinks current, or neither, depending on the phase difference of the phase detector input signals. During lock, very narrow pulses with a frequency equal to the PLL reference frequency are present. Output current is either 100 A or 400 A, selectable with bit 2/20. 125 100/ 400 A 5 PLL Gnd 6 Tx PD (Output) 7 Tx PLL VCC (Input) Ground pin for the PLL section. A direct connection to a ground plane is strongly recommended. Same as Pin 4, except powered from Tx PLL VCC. 10 7 0.01 10 VCC Tx PLL Section, MCU Serial Interface, Reference Oscillator 8 FTx (Input) 9 FTx MC (Output) Same as Pin 2. Tx Phase Detector Output. Description same as for Pin 4, except bit 1/20 controls the current level. Supply pin for the Tx PLL section, MCU Serial Interface, MCU Clock Counter, and the Reference Oscillator. Allowable range is 2.7 to 5.5 V and must be within 0.5 V of all other VCC pins. Good bypassing is required and isolation with a 10 resistor is recommended. Receives the signal from the external 64/65 or 128/129 prescaler. DC bias is at 1.5 V. Modulus Control Output for the Tx PLL section. Can be set to output in a current mode or a voltage mode, selectable with bit 3/16. Tx PLL VCC 100 A Current Mode 9 FTx MC Tx PLL VCC 100 A Voltage Mode NOTE: 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA 9 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 10 EN (Input) Description Tx PLL VCC 10 Enable 11 CLK (Input) 12 Data (I/O) Description Enable Input for the MCU Interface section. Hysteresis threshold is within 0.5 V of ground and VCC. See text for proper waveform required at this pin. 240 1.0 A Same as Pin 10. Clock Input for the MCU Interface section. Hysteresis threshold is within 0.5 V of ground and VCC. Data is written or read out on clock's rising edge. Maximum clock rate is 2.0 MHz. Data I/O line for the MCU Interface section. Both address and data are provided to/from this pin. Input threshold is within 0.5 V of ground and VCC. Data is written or read out on clock's rising edge. Tx PLL VCC 12 Data 240 1.0 A Tx PLL VCC Disable Data 13 MCU Clk Out (Output) Tx PLL VCC Tx PLL VCC 1.0 k 13 Clk Out The microprocessor clock output is derived from the reference oscillator and a programmable divider with divide ratios of 2 to 312.5. It can be used to drive a microprocessor and thereby reduce the number of crystals required in the system design. The driver has an internal resistor in series with the output which can be combined with an external capacitor to form a low-pass filter to reduce radiated noise on the PCB. This output also functions as the output for the counter test modes. 1) For the MC33411A the Clk Out can be disabled via the MCU interface. 2) For the MC33411B this output is always active (on). 14 NOTE: 10 Gnd Digital Ground for the Data, MCU Clk Out, and Fref Out digital Outputs. A direct connection to the ground plane is strongly recommended. 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 15, 16 Fref In, Fref Out Description Description Tx PLL VCC Fref Out 100 16 1) For the MC33411A the Fref Out can be disabled via the MCU interface. 2) For the MC33411B this output is always active (on). Tx PLL VCC 15 100 Fref In Disable 17 Reference Frequency Input for various portions of the circuit, including the PLLs, SCF clock, etc. A crystal (4 to 18.25 MHz) may be connected as shown, or an external frequency source may be capacitor coupled to Pin 15. See text for crystal requirements. DS Out (Output) VCC Audio Data Slicer Output (open collector with internal 100 k pull-up resistor). VCC Audio 100 k 17 DS Out 18 20 19 Tx Out (Output) 18, 20 Tx Out is the Tx path audio output. Internally this pin has a low-pass filter circuitry with -3.0 dB bandwidth of 4.0 kHz. Tx gain and mute are programmable through the MCU interface. This pin is sensitive to load capacitance. Tx Out,, C Out C Out is the compressor output. VCC Audio C Out (Output) VB Lim In (Input) Lim In is the limiter input. This pin is internally biased and has an input impedance of 400 k. Lim In must be ac-coupled. VCC Audio 400 k 19 Lim In VB 21 Ccap VCC Audio VCC Audio 40 k Ccap is the compressor rectifier filter capacitor pin. It is recommended that an external filter capacitor to VCC audio be used. A practical capacitor range is 0.1 to 1.0 F. The recommended value is 0.47 F. 21 Ccap NOTE: 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA 11 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 22 C In (Input) Description Description C In is the compressor input. This pin is internally biased and has an input impedance of 12.5 k. C In must be ac-coupled. VCC Audio 12.5 k 22 C In VB 23 VCC Audio (Input) 23 10 0.01 Audio Section, Filters, A/D Converters, Data Slicer 24 MCO (Output) Supply input for the audio section, filters, A/D Converters, and Data Slicer. Allowable range is 2.7 to 5.5 V. Good bypassing is required. VCC Output of the Microphone amplifier. Maximum output swing is 3.0 Vpp for VCC 3.0 V. Maximum output current is >1.0 mA peak. Audio VCC 24 MCO 25 MCI (Input) Inverting input of the microphone amplifier. Gain and frequency response are set with external resistors and capacitors from this pin to the audio source and to MCO. VCC Audio 25 VB MCI 2.5 A 26 Audio VCC VAG (Output) Analog ground for the audio section filters. VAG is equal to VB and is buffered from VB. Maximum current which can be sourced from this pin is 500 A. 26 VAG 30 k 27 Audio VCC VB (Output) 240 VCC PA (Input) 28 Audio Power NOTE: 12 10 VB 0.01 An internal 1.5 V reference for several sections. This voltage is adjustable with bits 3/20-17. Maximum source current is 100 A. PSRR, noise and crosstalk depends on the external capacitor. 27 30 k 28 0.1 F VCC 4.7 F Supply pin for the power amplifier outputs. Allowable range is 2.7 to 5.5 V. Good bypassing is required. 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 29 PAO+ (Output) Description Description Audio VCC 29 Output of the second power amplifier. This amplifier is set for unity inverting gain and is driven by PAO-. Maximum swing is 2.9 Vpp and maximum output current is >5.0 mA peak. DC level is 1.5 V. PAO+ 30 PAO- (Output) Same as Pin 29. Output of the first power amplifier. Its gain is set with external resistors and capacitors from this pin to PAI. Output capability is the same as Pin 28. 31 Gnd PA Ground pin for the power amplifier outputs. A direct connection to a ground plane is strongly recommended. 32 PAI (Input) Inverting input of the power amplifier. Gain and frequency response are set with external resistors and capacitors from this pin to the audio source and to PAO-. VCC Audio 32 VB PAI 2.5 A 33 E Out (Output) Expander output. This output is sensitive to load capacitance. Maximum output signal level is 2.5 Vpp. Maximum output current is >1.0 mA. Audio VCC 33 Rx Audio Output VB 34 Ecap VCC Audio VCC Audio 40 k 34 Ecap is the expander rectifier filter capacitor pin. Connect an external filter capacitor between VCC audio and Ecap. The recommended capacitance range is 0.1 to 1.0 F. The suggested value is 0.47 F. Ecap 35 E In (Input) The expander input pin is internally biased and has input impedance of 30 k. VCC Audio 35 30 k E In VB 36 VCC Audio Rx Out (Output) Rx Out is the Rx audio output. An internal low-pass filter has a -3.0 dB bandwidth of 4.0 kHz. 36 Rx Out VB NOTE: 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA 13 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 37 RSSI In (Input) Description Description VCC Audio Voltage input to RSSI A/D converter. Full scale is 0 to 1.6 V. 37 RSSI In 38 Rx Audio In (Input) Input to the Rx Audio Path. Input impedance is 600 k. Input signal must be capacitor coupled VCC Audio RC Network 38 600 k Rx Audio In VB 39 VCC Audio DS In (Input) Input for the digital data from the RF Receiver section. Input impedance is 250 k. Hysteresis is internally provided. Input signal level must be between 50 and 700 mVpp. 250 k 250 k 39 DS In 40 Gnd Audio 41 LO2 Out (Output) Ground pin for the audio section. A direct connection to a ground plan is strongly recommended. LO2 VCC LO2 VCC LO2 VCC 50 Buffered output of the 2nd LO. This high frequency output is a current, requiring an external pullup resistor. 41 LO2 Out 2.5 mA 42 LO2 VCC (Input) 42 LO2 Section NOTE: 14 10 0.01 10 VCC Supply pin for the LO2 section. Allowable range is 2.7 to 5.5 V and must be within 0.5 V of all other VCC pins. Good bypassing is required and isolation with a 10 resistor is recommended. 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAAAA AAAAAAAAAAAAAA MC33411A/B PIN FUNCTION DESCRIPTION (continued) Pin Symbol/Type 43, 45 LO2+, LO2- Description Description The 2nd LO. External tank components are required. The internal capacitance across the pins is adjustable from 0 to 7.6 pF for fine tuning performance with bits 7/20-18. LO2 VCC LO2 VCC 43 LO2+ 44 LO2 Ctl (Input) LO2 Control is the dc control input for this VCO. Typically it is the output of the low-pass filter fed from the phase detector output. 45 LO2- LO2 VCC 44 55 k LO2 Ctl 46 LO2 Gnd 47 LO2PD (Output) Ground pin for the LO2 section. A direct connection to a ground plane is strongly recommended. LO2 PLL VCC 100/ 400 A LO2 PLL VCC 125 47 to Filter LO2 PD LO2 Phase Detector Output. The output either sources or sinks current, or neither, depending on the phase difference of the phase detector input signals. During lock, very narrow pulses with a frequency equal to the PLL reference frequency are present. Output current is either 100 A or 400 A, selectable with bit 3/14. 125 100/ 400 A 48 NOTE: LO2 Gnd Ground pin for the LO2 section. A direct connection to a ground plane is strongly recommended. 1. All VCC pins must be within 0.5 V of each other. MOTOROLA RF/IF DEVICE DATA 15 MC33411A/B FUNCTIONAL DESCRIPTION The following text, graphics, tables and schematics are provided to the user as a source of valuable technical information about the MC33411. This information originates from thorough evaluation of the device performance. This data was obtained by using units from typical wafer lots. It is important to note that the forgoing data and information was from a limited number of units. By no means is the user to assume that the data following is a guaranteed parametric. Only the minimum and maximum limits identified in the electrical characteristics tables found earlier in the spec are guaranteed. Note: In the following descriptions, control bits in the MCU Serial Interface for the various functions will be identified by register number and bit number. For example, bit 3/19 indicates bit 19 of register 3. Bits 5/14-11 indicates register 5, bits 14 through 11. Please refer to Figure 1. General Circuit Description The MC33411A/B is a low power baseband IC designed to interface with the MC13145 UHF Wideband Receiver and MC13146 Transmitter for applications up to 2.0 GHz. The devices are primarily designated to be used for 900 MHz ISM band in a CT-900, low power, dual conversion cordless phone, but other applications such as data links with analog processing could be developed. This device contains complete baseband transmit and receive processing sections, a transmit and receive PLL section, a programmable PLL second local oscillator usable to 80 MHz, RSSI and low battery detect circuitry and serial interface for a microprocessor. "A" versions of the device have the ability to disable either the reference oscillator or MCU clock outputs. This feature is useful for systems where the MCU has an internal clock, allowing the user to place the MC33411 into Inactive (lowest power consumption) mode. The "A" version is also useful for systems where the MCU has a dedicated clock source, allowing for lower power consumption from the MC33411 by disabling the MCU clock output. "B" versions of the device are intended for systems where the MCU clock will always be driven from the MC33411. These bits are purposefully "hard-wired" to the enable state to ensure proper operation of the reference oscillator and MCU clock output even during battery discharge/recharge cycles. All internal registers are completely static - no refreshing is required under normal operation conditions. DC Current Figures 2 through 5 are the current consumption for Inactive (MC33411 "A" version only), Standby, Receive, and Active modes versus supply voltages. Figures 6 and 7 show the typical behavior of current consumption in relation to temperature. Figure 8 illustrates the effect of the MCU clock output frequency to supply current during Active mode. Figure 3. Supply Current versus Supply Voltage (Standby Mode) Figure 2. Supply Current versus Supply Voltage (Inactive Mode) 6.0 1.6 SUPPLY CURRENT (mA) SUPPLY CURRENT ( A) 5.0 1.8 TA = 25C 4.0 3.0 2.0 1.0 3.1 3.5 3.9 4.3 SUPPLY VOLTAGE (V) 16 4.7 5.1 1.4 1.2 1.0 0.8 0.6 0.4 MCU Clock Off 0 2.7 TA = 25C 5.5 0.0 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 SUPPLY VOLTAGE (V) MOTOROLA RF/IF DEVICE DATA MC33411A/B Figure 4. Supply Current versus Supply Voltage (Receive Mode) Figure 5. Supply Current versus Supply Voltage (Active Mode) 14 10 TA = 25C 9.5 SUPPLY CURRENT (mA) SUPPLY CURRENT (mA) TA = 25C MCU Clock Out On 9.0 8.5 MCU Clock Out Off MCU Clock Out On 13 MCU Clock Out Off 12 8.0 7.5 2.7 3.1 3.5 3.9 4.3 4.7 5.1 11 2.7 5.5 3.1 3.5 3.9 4.3 4.7 5.1 5.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 6. Supply Current versus Temperature Normalized to 25C (Standby Mode) Figure 7. Supply Current versus Temperature Normalized to 25C (Receive & Active Mode) 20 740 19 720 17 680 16 660 I CC, (mA) I CC, ( A) 18 700 VCC = 3.6 V Active 15 14 13 640 VCC = 3.6 V 12 620 600 -20 11 0 25 70 85 10 -20 Receive -5.0 10 25 40 55 70 85 DEGREES (C) DEGREES (C) Figure 8. Supply Current versus MCU Clock Output Frequency (Active Mode) SUPPLY CURRENT (mA) 12.5 12.3 VCC = 3.6 V TA = 25C 12.1 11.9 11.7 11.5 30 1030 2030 3030 4030 5030 MCU CLK OUT (kHz) MOTOROLA RF/IF DEVICE DATA 17 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA MC33411A/B Table 1. Tx Gain Adjust Programming (Register 7) Gain Control Bit #9 Gain Control Bit #8 Gain Control Bit #7 Gain Control Bit #6 Gain Ctl # Gain/Attenuation Amount <6 -9.0 dB 0 0 1 1 0 6 -9.0 dB 0 0 1 1 1 7 -8.0 dB 0 1 0 0 0 8 -7.0 dB 0 1 0 0 1 9 -6.0 dB 0 1 0 1 0 10 -5.0 dB 0 1 0 1 1 11 -4.0 dB 0 1 1 0 0 12 -3.0 dB 0 1 1 0 1 13 -2.0 dB 0 1 1 1 0 14 -1.0 dB 0 1 1 1 1 15 0 dB 1 0 0 0 0 16 1.0 dB 1 0 0 0 1 17 2.0 dB 1 0 0 1 0 18 3.0 dB 1 0 0 1 1 19 4.0 dB 1 0 1 0 0 20 5.0 dB 1 0 1 0 1 21 6.0 dB 1 0 1 1 0 22 7.0 dB 1 0 1 1 1 23 8.0 dB 1 1 0 0 0 24 9.0 dB 1 1 0 0 1 25 10 dB - - - - - >25 10 dB Transmit Speech Processing System This portion of the audio path goes from "Tx Audio" to "Tx Out". The gain of the microphone amplifier is set with external resistors to receive the audio from the microphone hybrid or any other audio source. The MCO output has rail-to-rail capability. The "Tx Audio" pin will be ac-coupled. The audio transmit signal path includes automatic level control (ALC) (also referred to as the Compressor), Tx mute, limiter, filters, and Tx gain adjust. The ALC provides "soft" limiting to the output signal swing as the input voltage slowly increases. With this technique the gain is slightly lowered to help reduce distortion of the audio signal. The limiter section provides hard limiting due to rapidly changing singal levels, or transients. The ALC, TX mute, and limiter functions can be enabled or disabled vis the MCU serial interface. The Tx gain adjust can also be remotely controlled to set different desired signal levels. The adjustable gain stage provides 20 levels of gain in 1.0 dB increments. It is controlled with bits 7/9-5 as shown in Table 1. The effect of the gain setting under various ALC/Limiter On/Off settings is shown in Figure 9. The Low-Pass Filter before the gain stage is a switched capacitor filter with a corner frequency at 3.7 kHz. This 18 Gain Control Bit #5 frequency is dependent upon the SCF clock, nominaly set to 165 kHz and is directly proportional to the SCF clock. The filter response for inband, ripple, wideband, as well as phase and group delay, are shown in Figures 10 through 14. The mute switch at Pin 18 will mute a minimum of 60 dB. Bit 6/2 controls the mute. The limiter can be disabled by programming a logic 1 into 6/5. The compressor with ALC transfer characteristic is shown in Figure 15. The ALC gain is controlled by bits 6/11-12. If both bits are programmed to a logic 0, the ALC gain is set to 5.0 dB. If bit 6/11 is set to a logic 1, the ALC gain will be set to 10 dB, whereas if bit 6/12 is set to a logic 1 the ALC gain will be 25 dB. The ALC function may be disabled by programming a logic 1 into bit 6/6. The compressor low maximum gain can be set with bit 6/8. Programming this bit to a logic 0 sets the maximum gain to 23 dB. A lower maximum gain, nominally 13.5 dB, is achieved by programming the bit to a logic 1. The entire compressor can be bypassed (i.e., 0 dB) by programming bit 6/4 to a logic 1. Figures 16 through 22 describe the characteristics of the compressor, ALC, and limiter. MOTOROLA RF/IF DEVICE DATA MC33411A/B 2.0 0 -2.0 -4.0 -6.0 -8.0 -10 -12 -14 -16 -18 -20 -9.0 VCC = 3.6 V TA = 25C Vin = -10 dBV Figure 10. Lim In to Tx Out Gain versus Frequency (Inband) ALC Off, Limiter Off VOLTAGE GAIN (dB) MAX Tx OUT VOLTAGE (dBV) Figure 9. Tx Audio Output Voltage versus Gain Control Setting ALC Off, Limiter On ALC On, Limiter On/Off -7.0 -5.0 -3.0 -1.0 1.0 3.0 5.0 7.0 9.0 11 -0.8 Figure 12. Lim In to Tx Out Gain versus Frequency (Wideband) VCC = 3.6 V TA = 25C Vin = -10 dBV -1.0 -1.1 -1.2 -1.3 -1.4 -1.5 100 1000 10000 -50 -60 -70 -80 -90 -100 100 VCC = 3.6 V TA = 25C Vin = -10 dBV 1000 10000 100000 f, FREQUENCY (Hz) Figure 13. Lim In to Tx Out Phase versus Frequency Figure 14. Lim In to Tx Out Group Delay versus Frequency 1000000 10 VCC = 3.6 V TA = 25C Vin = -10 dBV GROUP DELAY (ms) PHASE (degrees) 10 0 -10 -20 -30 -40 f, FREQUENCY (Hz) 180 90 10000 Figure 11. Lim In to Tx Out Gain versus Frequency (Ripple) -0.9 135 1000 f, FREQUENCY (Hz) VOLTAGE GAIN (dB) VOLTAGE GAIN (dB) -0.7 VCC = 3.6 V TA = 25C Vin = -10 dBV Tx GAIN SETTING (dB) -0.5 -0.6 5.0 0 -5.0 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 100 45 0 -45 VCC = 3.6 V TA = 25C Vin = -10 dBV 1.0 0.1 -90 -135 -180 100 1000 f, FREQUENCY (Hz) MOTOROLA RF/IF DEVICE DATA 10000 0 100 1000 10000 f, FREQUENCY (Hz) 19 MC33411A/B Figure 16. Tx Audio Compressor Response (Distortion & Amplitude, ALC off, Lim off) 0 0 Vin > = -4.0 dBV, Vout = 1.26 Vpp (rapidly changing limited signals) -5.0 Vin = -2.5 dBV, Vout = -10 dBV "Comp Low Max Gain En" = 0 -20 Maximum Gain = 21 -33 -40 Compressor Transfer 10 -15 -20 8.0 -25 6.0 -30 4.0 -35 2.0 -40 -50 -60 -50 -40 -30 -20 C IN (dBV) -10 -45 -60 0 -5.0 -20 8.0 -25 6.0 -30 4.0 -35 -50 -40 -30 -20 -10 0 -10 0 10 VCC = 3.6 V TA = 25C 3.0 Tx Out -20 2.0 -25 1.0 -30 0 -40 -60 Distortion -50 -40 -30 -20 -10 0 Figure 20. Tx Output Audio Response (Lim off, ALC on) 4.0 -5.0 3.0 2.0 Tx Out -25 -30 1.0 Distortion -50 -40 -30 -20 MCI VOLTAGE (dBV) VCC = 3.6 V TA = 25C 3.0 -10 -15 Tx Out -20 2.0 -25 -30 1.0 Distortion -35 -10 0 0 10 0 10 4.0 0 VCC = 3.6 V TA = 25C -35 0 4.0 Figure 19. Tx Output Audio Response (Lim on, ALC off) -20 10 -15 -35 -15 20 -20 MCI VOLTAGE (dBV) -10 -40 -60 -30 C IN VOLTAGE (dBV) 0 -5.0 -40 -10 2.0 Tx OUT VOLTAGE (dBV) -45 -60 Distortion Tx OUT VOLTAGE (dBV) 12 10 -15 -40 Tx OUT VOLTAGE (dBV) 0 DISTORTION (%) Compressor Transfer 14 DISTORTION (%) C OUT VOLTAGE (dBV) -10 -50 Figure 18. Tx Output Audio Response (Lim & ALC off) 0 -5.0 Distortion C IN VOLTAGE (dBV) Figure 17. Tx Audio Compressor Response (Distortion & Amplitude, ALC off, Lim off) VCC = 3.6 V TA = 25C R6/8 = 0 12 -40 -60 DISTORTION (%) -30 -20 Vin = -16 dBV, Vout = -13 dBV (slowly changing ALC signals) "Comp Low Max Gain En" = 1.0 Maximum Gain = 12 -23.5 -10 -50 -40 -30 -20 -10 0 0 10 MCI VOLTAGE (dBV) MOTOROLA RF/IF DEVICE DATA DISTORTION (%) -30 C OUT VOLTAGE (dBV) C OUT (dBV) -10 14 VCC = 3.6 V TA = 25C R6/8 = 1 DISTORTION (%) Figure 15. Compressor Characteristic with Programmable Compressor Maximum Gain MC33411A/B Figure 22. Tx Output Audio Response (Lim off, R6/12 = 1) 4.0 0 3.0 -10 -15 -20 2.0 Tx Out -25 1.0 -30 Distortion -35 -40 -60 -50 -40 -30 -20 Tx OUT VOLTAGE (dBV) -5.0 DISTORTION (%) Tx OUT VOLTAGE (dBV) -5.0 4.0 0 VCC = 3.6 V TA = 25C VCC = 3.6 V TA = 25C 3.0 -10 -15 Tx Out -20 -25 1.0 -30 Distortion -35 -10 0 10 0 2.0 -40 -60 DISTORTION (%) Figure 21. Tx Output Audio Response (Lim off, R6/11 = 1) -50 -40 MCI VOLTAGE (dBV) -30 -20 -10 0 0 10 MCI VOLTAGE (dBV) Data Slicer The data slicer will receive the low level digital signal from the RF receiver section at Pin 39. The input signal to the data slicer must be >200 mVpp. Hysteresis of 40 mV is internally provided. The output of the data slicer will be same waveform, but with an amplitude of 0 to VCC, and can be observed at Pin 17 if bits 5/9-8 are set to 00. The output can be inverted by setting bit 5/9 = 1. The data slicer can be disabled by setting bit 5/8 = 1. Receive Audio Path The Receive Audio Path (Pins 38, 36-33) consists of an anti-aliasing filter, a low-pass filter, side tone attenuator, gain adjust stage, a mute switch, expander and volume control. The switched capacitor low-pass filter is an 8 pole filter, with a corner frequency at 3.8 kHz. This is designed to provide bandwidth limiting in the audio range. The gain stage provides 20 dB of gain adjustment in 1.0 dB steps, measured from Pin 38 to 36. Bits 7/4-0 are used to set the gain according to Table 3. The mute switch, controlled by bit 6/1, will mute a minimum of 60 dB. When the compressor output is within 3.0 dB of the expander input level, the Rx output (Pin 36) can be attenuated (referenced to the expander output) by bits 6/10-9. For 6/10-9 = 00, the attenuation is 0 dB. For the other combinations, 6/10-9 = 01, attenuation = 3.0 dB; 6/10-9 = 10, attenuation = 6.0 dB; and 6/10-9 = 11, attenuation = 10.4 dB (See Table 2). The expander can be bypassed by setting bit 6/3 = 1. Table 3 shows the various gain control settings which can be accessed in Register 7. Table 4 is the volume control settings, also located in Register 7. Figures 23 through 31 illustrate the various characteristics of the reveive audio path. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 2. Side Tone Attenuate Programming Side Tone Attenuate Bit #1 Side Tone Attenuate Bit #0 Select # Side Tone Attenuate Amount at Expander Input Side Tone Attenuate Amount at Expander Output 0 0 0 0 dB 0 dB 0 1 1 1.5 dB 3.0 dB 1 0 2 3.0 dB 6.0 dB 1 1 3 5.2 dB 10.4 dB AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 3. Rx Gain Adjust Programming (Register 7) Gain Control Bit #4 Gain Control Bit #3 Gain Control Bit #2 Gain Control Bit #1 Gain Control Bit #0 Gain Ctl # Gain/Attenuation Amount - - - - - <6 -9.0 dB 0 0 1 1 0 6 -9.0 dB 0 0 1 1 1 7 -8.0 dB 0 1 0 0 0 8 -7.0 dB 0 1 0 0 1 9 -6.0 dB 0 1 0 1 0 10 -5.0 dB 0 1 0 1 1 11 -4.0 dB 0 1 1 0 0 12 -3.0 dB 0 1 1 0 1 13 -2.0 dB MOTOROLA RF/IF DEVICE DATA 21 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA MC33411A/B Table 3. Rx Gain Adjust Programming (Register 7) (continued) Gain Control Bit #4 Gain Control Bit #3 Gain Control Bit #2 Gain Control Bit #1 Gain Control Bit #0 Gain Ctl # Gain/Attenuation Amount 0 1 1 1 0 14 -1.0 dB 0 1 1 1 1 15 0 dB 1 0 0 0 0 16 1.0 dB 1 0 0 0 1 17 2.0 dB 1 0 0 1 0 18 3.0 dB 1 0 0 1 1 19 4.0 dB 1 0 1 0 0 20 5.0 dB 1 0 1 0 1 21 6.0 dB 1 0 1 1 0 22 7.0 dB 1 0 1 1 1 23 8.0 dB 1 1 0 0 0 24 9.0 dB 1 1 0 0 1 25 10 dB - - - - - >25 10 dB AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 4. Volume Control Programming Volume Control Bit #13 Volume Control Bit #12 Volume Control Bit #11 Volume Control Bit #10 Volume Ctl # Gain/Attenuation Amount 0 0 0 0 0 -14 dB 0 0 0 1 1 -12 dB 0 0 1 0 2 -10 dB 0 0 1 1 3 -8.0 dB 0 1 0 0 4 -6.0 dB 0 1 0 1 5 -4.0 dB 0 1 1 0 6 -2.0 dB 0 1 1 1 7 0 dB 1 0 0 0 8 2.0 dB 1 0 0 1 9 4.0 dB 1 0 1 0 10 6.0 dB 1 0 1 1 11 8.0 dB 1 1 0 0 12 10 dB 1 1 0 1 13 12 dB 1 1 1 0 14 14 dB 1 1 1 1 15 16 dB 22 MOTOROLA RF/IF DEVICE DATA MC33411A/B Figure 24. E Out Maximum Output Voltage versus Volume Control Setting -10 -12 -14 -16 -18 -20 -9.0 5.0 0 -5.0 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 100 1.4 VCC = 3.6 V TA = 25C MAX E OUT VOLTAGE (dBV) 2.0 0 -2.0 -4.0 -6.0 -8.0 -7.0 -5.0 -3.0 -1.0 1.0 3.0 5.0 7.0 9.0 1.0 0.8 0.6 -10 -6.0 -2.0 2.0 6.0 10 VOLUME SETTING (dB) Figure 25. Rx Audio In to Rx Out Gain versus Frequency (Inband) Figure 26. Rx Audio In to Rx Out Gain versus Frequency (Ripple) 14 0.3 0.2 0.1 VCC = 3.6 V TA = 25C Vin = -20 dBV 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 1000 VCC = 3.6 V TA = 25C Vin = -20 dBV -0.7 100 10000 1000 f, FREQUENCY (Hz) f, FREQUENCY (Hz) Figure 27. Rx Audio In to Rx Out Gain versus Frequency (Wideband) Figure 28. Rx Audio In to Rx Out Phase versus Frequency 1000 180 0 -10 VCC = 3.6 V TA = 25C Vin = -20 dBV 135 90 PHASE (degrees) -20 -30 -40 -50 -60 45 0 -45 -70 -90 -80 -90 -135 -100 100 VCC = 3.6 V TA = 25C Rx GAIN SETTING (dB) 10 VOLTAGE GAIN (dB) 1.2 0.4 -14 11 VOLTAGE GAIN (dB) VOLTAGE GAIN (dB) MAX Rx OUT VOLTAGE (dBV) Figure 23. Rx Out Maximum Output Voltage versus Gain Control Setting 1000 10000 f, FREQUENCY (Hz) MOTOROLA RF/IF DEVICE DATA 100000 1000000 -180 100 VCC = 3.6 V TA = 25C Vin = -20 dBV 1000 1000 f, FREQUENCY (Hz) 23 MC33411A/B Figure 30. AALPF Response Gain versus Frequency Figure 29. Rx Audio In to Rx Out Group Delay versus Frequency 1.0 10 0 -10 VCC = 3.6 V TA = 25C Vin = -20 dBV VOLTAGE GAIN (dB) GROUP DELAY (ms) 10 0.1 -20 -30 -40 -50 -60 -70 -80 -90 0 100 1000 -100 100 10000 f, FREQUENCY (Hz) VCC = 3.6 V TA = 25C Vin = -20 dBV SCF Clk = 2.5 MHz SCF Corner = 57 kHz 1000 10000 100000 1000000 f, FREQUENCY (Hz) Figure 31. E In to E Out Transfer Curve 5.0 VCC = 3.6 V TA = 25C 24 20 -15 -25 16 Expander Transfer 12 -35 8.0 -45 DISTORTION (%) E OUT VOLTAGE (dBv) -5.0 28 Distortion 4.0 -55 -65 -40 -35 -30 -25 -20 -15 -10 -5.0 0 0 E IN VOLTAGE (dBV) 24 MOTOROLA RF/IF DEVICE DATA MC33411A/B Power Amplifiers The power amplifiers (Pins 29, 30, 32) are designed to drive the earpiece in a handset, or the telephone line via a hybrid circuit in the base unit. Each output (PAO+ and PAO-) can source and sink 5.0 mA, and can swing 1.3 Vpp each. For high impedance loads, each output can swing 2.7 Vpp (5.4 Vpp differential). The gain of the amplifiers is set with a feedback resistor from Pin 30 to 32, and an input resistor at Pin 32. The differential gain is 2x the resistor ratio. Capacitors can be used for frequency shaping. The pins' dc level is VB (1.5 V). The Mute switch, controlled with bit 6/0, will provide 60 dB of muting with a 50 k feedback resistor. The amount of muting will depend on the value of the feedback resistor. F i g u r e s 32 a n d 33 s h o w t h e p o w e r a m p l i f i e r swing/distortion for VCC = 3.6 V, and Figure 34 illustrates the maximum swing capability for various value of VCC. Figure 33. Power Amplifier Distortion Figure 32. Power Amplifier Maximum Output Swing 3.2 20 PAO- (DISTORTION %) 2.4 PAO- (Vpp ) VCC = 3.6 V TA = 25C Open 2.8 130 2.0 1.6 1.2 0.8 10 Open 5.0 VCC = 3.6 V TA = 25C 0.4 0 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 PAI (Vpp) 3.5 3.0 0 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 PAI (Vpp) Figure 34. Power Amplifier Maximum Output Swing versus VCC Open TA = 25C 130 2.5 PAO- (Vpp ) 130 15 2.0 1.5 1.0 0.5 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VCC (V) MOTOROLA RF/IF DEVICE DATA 25 4.4 MC33411A/B Reference Oscillator/MCU Clk Out The reference oscillator provides the frequency basis for the three PLLs, the switched capacitor filters, and the MCU clock output. The source for the reference clock can be a crystal in the range of 4.0 to 18.25 MHz connected to Pins 15 & 16, or it can be an external source connected to Fref In (Pin 15). The reference frequency is directed to: a. A programmable 12-bit counter (register bits 4/11-0) to provide the reference frequency for the three PLLs. The 12-bit counter is to be set such that, in conjunction with the programmable counters within each PLL, the proper frequencies can be produced by each VCO. b. A programmable 6-bit counter (register bits 4/17-12), followed by a /2 stage, to set the frequency for the switched capacitor filters to 165 kHz, or as close to that as possible. c. A programmable 3-bit counter (register bits 7/16-14) which provides the MCU clock output (see Tables 5 and 6). A representation of the reference oscillator is given by Figures 35 and 36. Figure 35. Reference Oscillator Schematic Reference Oscillator RPI CPI Gm Fref In CPO AAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAA AAAAAAAAA AAAAAAAA Figure 36. Reference Oscillator Input and Output Impedance Input Impedance (RPI // CPI) 11.6 k // 2.9 pF Output Impedance (RPO // CPO) 4.5 k // 2.5 pF Figures 37 and 38 show a typical gain/phase response of the oscillator. Load capacitance (CL), equivalent series resistance (ESR), and even supply voltage will have an effect on the oscillator response as shown in Figures 39 and 40. It should be noted that optimum performance is achieved when C1 equals C2 (C1/C2 = 1). Figure 41 represents the ESR versus crystal load capacitance for the reference oscillator. This relationship was defined by using a 6.0 dB minimum loop gain margin at 3.6 V. This is considered the minimum gain margin to guarantee oscillator start-up. Oscillator start-up is also significantly affected by the crystal load capacitance selection. In Figure 39, the relationship between crystal load capacitance and ESR can be seen. The lower the load capacitance the better the performance. Given the desired crystal load capacitance, C1 and C2 can be determined from Figure 42. It should also be pointed out that current consumption increases when C1 C2. Be careful not to overdrive the crystal. This could cause a noise problem. An external series resistor on the crystal output can be added to reduce the drive level, if necessary. RPO Fref Out Xtal C1 26 C2 MOTOROLA RF/IF DEVICE DATA MC33411A/B Figure 38. Reference Oscillator Open Loop Phase versus Frequency Figure 37. Reference Oscillator Open Loop Gain versus Frequency 16 100 14 10 8.0 60 PHASE (degrees) VOLTAGE GAIN (dB) 12 VCC = 3.6 V TA = 25C 10.24 MHz, 10 pF Load Capacitance Crystal 80 VCC = 3.6 V TA = 25C 10.24 MHz, 10 pF Load Capacitance Crystal 6.0 Fref out Fref in 16 15 4.0 2.0 40 20 0 Fref out Fref in 16 15 -20 -40 -60 0 13 pF -2.0 -4.0 10.237 10.238 10.239 13 pF 10.240 13 pF -80 10.241 10.242 -100 10.237 10.243 13 pF 10.238 f, FREQUENCY (MHz) 10.240 10.241 10.242 10.24 f, FREQUENCY (MHz) Figure 39. Reference Oscillator Startup Time versus Total ESR - Inactive to Rx Mode Figure 40. Reference Oscillator Open Loop Gain versus ESR 5.0 20 VCC = 3.6 V TA = 25C 4.0 VCC = 3.6 V TA = 25C 16 3.0 GAIN (dB) START UP TIME (ms) 10.239 2.048 MHz 2.0 12 8.0 5.12 MHz 4.0 1.0 0 0 50 100 150 200 250 300 0 350 0 50 100 150 200 250 300 350 TOTAL ESR () TOTAL ESR () Figure 41. Maximum ESR versus Crystal Load Capacitance (C1 = C2) Figure 42. Optimum Values for C1, C2 versus Equivalent Required Parallel Capacitance 1000 70 50 C1 AND C2 (pF) MAXIMUM ESR () 60 100 40 30 20 10 10 10 12 14 16 18 20 22 24 26 CRYSTAL LOAD CAPACITANCE (pF) MOTOROLA RF/IF DEVICE DATA 28 30 32 0 5.0 10 15 20 25 30 35 CRYSTAL LOAD CAPACITANCE (pF) 27 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA MC33411A/B Table 5. MCU Clock Divider Programming MCU Clk Bit #16 MCU Clk Bit #15 MCU Clk Bit #14 Clk Out Divider Value 0 0 0 2.0 0 0 1 3.0 0 1 0 4.0 0 1 1 5.0 1 0 0 2.5 1 0 1 20 1 1 0 80 1 1 1 312.5 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 6. MCU Clock Divider Frequencies Clock Output Divider Crystal Frequency 2.0 2.5 3.0 4.0 5.0 20 80 312.5 10.24 MHz 5.12 MHz 4.096 MHz 3.413 MHz 2.56 MHz 2.048 MHz 512 kHz 128 kHz 32.768 kHz 11.15 MHz 5.575 MHz 4.46 MHz 3.717 MHz 2.788 MHz 2.23 MHz 557 kHz 139 kHz 35.68 kHz 12 MHz 6.0 MHz 4.8 MHz 4.0 MHz 3.0 MHz 2.4 MHz 600 kHz 150 kHz 38.4 kHz Transmit and Receive (LO1) PLL Sections The transmit and receive PLLs (Pins 6-9 and 1-4, respectively) are designed to be part of a 900 MHz system. In a typical application the Transmit PLL section will be set up to generate the transmit frequency, and the Receive PLL section will be set up to generate the LO1 frequency. The two sections are identical, and function independently. External requirements for each include a low-pass filter, a 900 MHz VCO, and a 64/65 or 128/129 dual modulus prescaler. The frequency output of the VCO is to be reduced by the dual modulus prescaler, and then input to the MC33411 (at Pin 8 or 2). That frequency is then further reduced by the programmable 13-bit counter (bits 1/19-7 or 2/19-7), and provided to one side of the Phase Detector, where it is compared with the PLL reference frequency. The output of the phase detector (at Pin 6 or 4) is a Three-State charge pump which drives the VCO through the low-pass filter. Bits 1/20 and 2/20 set the gain of each of the two charge pumps to either 100/2 A/radian or 400/2 A/radian. The polarity of the two phase detector outputs is set with bits 1/21 and 2/21. If the bit = 0, the appropriate PLL is configured to operate with a non-inverting low-pass filter/VCO combination. If the low-pass filter/VCO combination is inverting, the polarity bit should be set to 1. The 7-bit A and A' counters (bits 1/6-0 and 2/6-0) are to be set to drive the Modulus Control input of the 64/65 or 128/129 dual modulus prescalers. The Modulus Control outputs (Pins 9 and 1) can be set to either a voltage mode (logic 1) or a current mode (logic 0) with bit 3/16. To calculate the settings of the N and A registers, the following procedure is used: 28 f VCO f PLL Nt P + Nt (Nt must be an integer) +N (1) (2) A = Remainder of Equation 2 (decimal part of N x P) (3) where: fVCO = the VCO frequency fPLL = the PLL Reference Frequency set within the MC33411 P = the smaller divisor of the dual modulus prescaler (64 for a 64/65 prescaler) N = the whole number portion is the setting for the N (or N') counter within the MC33411 A = the setting for the A (or A') counter within the MC33411 For example, if the VCO is to provide 910 MHz, and the internal PLL reference frequency is 50 kHz, then the equations yield: Nt x 10 6 + 18, 200 + 910 50 x 10 3 N + 18,64200 + 284.375 A + 0.375 x 64 + 24 The N register setting is 284 (0 0001 0001 1100), and the A register setting is 24 (001 1000). MOTOROLA RF/IF DEVICE DATA MC33411A/B 2nd LO (LO2) This PLL is designed to be the 2nd Local Oscillator in a typical 900 MHz system, and is designed for frequencies up to 80 MHz. The VCO and varactor diodes are included, and are to be used with an external tank circuit (Pins 43-45). Bits 4/20-18 are used to select an internal capacitor, with a value in the range of 0 to 7.6 pF, to parallel the varactor diodes and the tank's external capacitor. This permits a certain amount of fine tuning of the oscillator's performance. See Table 7. A buffered output is provided to drive, e.g., a mixer. The frequency is set with the programmable 14-bit counter (bits 3/13-0) in conjunction with the PLL reference frequency. For example, if the reference frequency is 50 kHz, and the 2nd LO frequency is to be 63.3 MHz, the 14-bit counter needs to be set to 1266d (00 0100 1111 0010). The output level is dependent on the value of the impedance at Pin 41, partly determined by the external pull-up resistor. The output of the phase detector is a Three-State charge pump which drives the varactor diodes through an external low-pass filter. Bit 3/14 sets the gain of the charge pump to either 100/2 A/radian (logic 0) or 400/2 A/radian (logic 1). Bit 3/15 sets its polarity - if 0, the PLL is configured to operate with a non-inverting low-pass filter/VCO combination. If the low-pass filter/VCO combination is inverting, the polarity bit should be set to 1. Please note that the 2nd LO VCO on the MC33411 is of the non-inverting type. Figures 43 through 45 describe the response of the 2nd LO. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 7. LO2 Capacitor Select Programming LO2 Capacitor Select Bit #20 LO2 Capacitor Select Bit #19 LO2 Capacitor Select Bit #18 Select # LO2 Capacitor Select Value 0 0 0 0 0 pF 0 0 1 1 1.1 pF 0 1 0 2 2.2 pF 0 1 1 3 3.3 pF 1 0 0 4 4.3 pF 1 0 1 5 5.4 pF 1 1 0 6 6.5 pF 1 1 1 7 7.6 pF MOTOROLA RF/IF DEVICE DATA 29 MC33411A/B Figure 44. Minimum Overall Q versus Coil Inductance for LO2 Figure 43. Varicap Capacitance versus Control Voltage 16 80 VCC = 3.6 V TA = 25C 15 MINIMUM OVERALL Q CAPACITANCE (pF) 14 70 13 12 11 10 9.0 8.0 60 50 60 MHz 40 30 20 7.0 10 6.0 0 0 1 2 3 4 5 6 VCC = 3.6 V TA = 25C 30 MHz 80 MHz 0 200 400 600 800 1000 1200 COIL INDUCTANCE (nH) CONTROL VOLTAGE (V) Figure 45. LO2 Amplitude versus Overall Tank Parallel Resistance 35 LO AMPLITUDE (dBmV) 30 VCC = 3.6 V TA = 25C FLO = 63.3 MHz 25 20 15 10 5 0 0 500 1000 1500 2000 2500 3000 3500 TANK RESISTANCE () 30 MOTOROLA RF/IF DEVICE DATA MC33411A/B Loop Filter Characteristics Let's consider the following discussion on loop filters. The fundamental loop characteristics, such as capture range, loop bandwidth, lock-up time, and transient response are controlled externally by loop filtering. Figure 46 is the general model for a Phase Lock Loop (PLL). pole and a zero around the 0 dB point to guarantee sufficient phase margin in this design (Qp in Figure 48). Figure 48. Bode Plot of Gain and Phase in Open Loop Condition 0 fi Phase Detector (Kpd) Filter (Kf) VCO (Ko) fo A, Open Loop Gain Open Loop Gain Figure 46. PLL Model 0 -90 Phase Divider (Kn) Qp Where: Kpd = Phase Detector Gain Constant Kf = Loop Filter Transfer Function Ko = VCO Gain Constant Kn = Divide Ratio (N) fi = Input frequency fo = Output frequency fo/N = Feedback frequency divided by N From control theory the loop transfer function can be represented as follows: A + K K K pd f o Kn p A Figure 47. Loop Filter with Additional Integrating Element From Phase Detector To VCO C1 MOTOROLA RF/IF DEVICE DATA K jwK n K (1 pd o (4) The two time constants creating the pole and the zero in the Bode plot can now be defined as: R2C1C2 + C1 ) C2 T1 T2 + R2C2 By substituting equation (5) into (4), it follows: A openloop + K K T1 pd o w 2C1K nT2 1 1 (5) ) jwT2 ) jwT1 (6) The phase margin (phase + 180) is thus determined by: Qp + arctan(wT2)-arctan(wT1) (7) At =p, the derivative of the phase margin may be set to zero in order to assure maximum phase margin occurs at p (see also Figure 48). This provides an expression for p: R2 dQ p C2 dw From Figure 47, capacitor C1 forms an additional integrator, providing the type 2 response, and filters the discrete current steps from the phase detector output. The function of the additional components R2 and C2 is to create a pole and a zero (together with C1) around the 0 dB point of the open loop gain. This will create sufficient phase margin for stable loop operation. In Figure 48, the open loop gain and the phase is displayed in the form of a Bode plot. Since there are two integrating functions in the loop, originating from the loopfilter and the VCO gain, the open loop gain response follows a second order slope (-40 dB/dec) creating a phase of -180 degrees at the lower and higher frequencies. The filter characteristic needs to be determined such that it is adding a ) jw(R2C2)) jw 1 ) jw R2C1C2 C1)C2 + openloop Open loop gain Kpd can be either expressed as being 200 A/4 or 800 A/4. More details about performance of different type PLL loops, refer to Motorola application note AN535. The loop filter can take the form of a simple low pass filter. A current output, type 2 filter will be used in this discussion since it has the advantage of improved step response, velocity, and acceleration. The type 2 low pass filter discussed here is represented as follows: -180 The open loop gain including the filter response can be expressed as: +0+ T2 - T1 ) (wT2)2 1 ) (wT1)2 w + wp + 1 T2T1 (8) 1 (9) Or rewritten: T1 + w 12T2 p (10) By substituting into equation (7), solve for T2: T2 + tan Qp 2 ) p4 wp (11) 31 MC33411A/B By choosing a value for p and Qp, T1 and T2 can be calculated. The choice of Qp determines the stability of the loop. In general, choosing a phase margin of 45 degrees is a good choice to start calculations. Choosing lower phase margins will provide somewhat faster lock-times, but also generate higher overshoots on the control line to the VCO. This will present a less stable system. Larger values of phase margin provide a more stable system, but also increase lock-times. The practical range for phase margin is 30 degrees up to 70 degrees. The selection of p is strongly related to the desired lock-time. Since it is quite complicated to accurately calculate lock time, a good first order approach is: T_lock [ w3p (12) Equation (12) only provides an order of magnitude for lock time. It does not clearly define what the exact frequency difference is from the desired frequency and it does not show the effect of phase margin. It assumes, however, that the phase detector steps up to the desired control voltage without hesitation. In practice, such step response approach is not really valid. If the two input frequencies are not locked, their phase maybe momentarily zero and force the phase detector into a high impedance mode. Hence, the lock times may be found to be somewhat higher. In general, p should be chosen far below the reference frequency in order for the filter to provide sufficient attenuation at that frequency. In some applications, the reference frequency might represent the spacing between channels. Any feedthrough to the VCO that shows up as a spur might affect adjacent channel rejection. In theory, with the loop in lock, there is no signal coming from the phase detector. But in practice small current pulses and leakage currents will be supplied to both the VCO and the phase detector. The external capacitors may show some leakage, too. Hence, the lower p, the better the reference frequency is filtered, but the longer it takes for the loop to lock. As shown in Figure 48, the open loop gain at p is 1 (or 0 dB), and thus the absolute value of the complex open loop gain as shown in equation (6) solves C1: C1 + K K T1 pd o w 2KnT2 ) ) 1 1 wpT2 wpT1 32 *1 + C1 T2 T1 R2 + T2 C2 f + 2p 1LC 2 (16) T In which L represents the external inductor value and CT represents the total capacitance (including internal capacitance) in parallel with the inductor. The VCO gain can be easily calculated via the internal varicap transfer curve shown in Figure 43. As can be derived from Figure 43, the varicap capacitance changes 2.0 pF over the voltage range from 1.0 V to 3.0 V: pF DCvar + 2.0 2.0 V (17) Combining (16) with (17) the VCO gain can be determined by: Ko 1 + j2.0V * 1 2p LC T 2p L C 1 T ) DCvar 2 (18) Although the basic loopfilter previously described provides adequate performance for most applications, an extra pole may be added for additional reference frequency filtering. Given that the channel spacing is based on the reference frequency, and any feedthrough to the first LO may effect parameters like adjacent channel rejection and intermodulation. Figure 49 shows a loopfilter architecture incorporating an additional pole. Figure 49. Loop Filter with Additional Integrating Element From Phase Detector To VCO R3 R2 2 (13) With C1 known, and equation (5) solve C2 and R2: C2 The VCO gain is dependent on the selection of the external inductor and the frequency required. The free running frequency of the VCO is determined by: (14) C1 C2 C3 For the additional pole formed by R3 and C3 to be efficient, the cut-off frequency must be much lower than the reference frequency. However, it must also be higher than p in order not to compromise phase margin too much. The following equations were derived in a similar manner as for the basic filter previously described. (15) MOTOROLA RF/IF DEVICE DATA MC33411A/B Similarly, it can be shown: A +- openloop K K nw 2 (C1 In which: K pd o ) C2 ) C3) - w2C1C2C3R2R3 T1 ) (C1C2)T3 + C1(C1))C2C2))T2 C3 * w 2C1T2T3 T2 + R2C2 ) 11 )) jjwwT2 T1 (19) (20) (21) T3 + R3C3 (22) From T1 it can be derived that: C2 ) T3 * T1 ) w T1T2T3 + (T1 ) T2)C3 * C1 T2 T3 * T1 2 (23) In analogy with (13), by forcing the loopgain to 1 (0 dB) at p, we obtain: C1(T1 ) T2) ) C2T3 ) C3T2 + K K pd o K nw p 2 Solving for C1: (T2 C1 + 1 1 * T1)T3C3 * (T3 * T1)T2C3 ) (T3 * T1) (T3 * T1)T2 ) (T3 * T1)T3 * T2 ) ) wpT1 + Kw1 p MOTOROLA RF/IF DEVICE DATA 2 K T1 pd o w p 2K n (24) ) wpT2 2 1) w pT1 1 ) T3 * T1 ) wp2T1T2T3 T3 (26) The K-factor shown determines how far the additional pole frequency will be separated from p. Selecting too small of a K-factor, the equations may provide negative capacitance or resistor values. Too large of a K-factor may not provide the maximum attenuation. By selecting R3 to be 100 k, C3 becomes known and C1 and C2 can be solved from the equations. By using equations (11) and (10), time constants T2 and T1 can be derived by selecting a phase margin. Finally, R2 follows from T2 and C2. A test circuit with the following components and conditions was constructed with these results: Loop Filter (See Figure 49): C1 = 470 pF R2 = 68 k C2 = 3.9 nF R3 = 270 k C3 = 82 pF 2 K By selecting p via (12), the additional time constant expressed as T3, can be set to: T3 wpT2 2 (25) LO2 Tank: Ctotal = 39.3 pF Lext = 150 nH, Q = 50 @ 250 MHz Reference Frequency = 10.24 MHz (unadjusted) R Counter = 205 LO2 Counter = 1266 AC Load = 25 Frequency of LO2 = 63.258 MHz Phase Noise @ 50 kHz offset = -107 dBc Sidebands @ 50 kHz & 100 kHz offsets = -69 dBc Low Battery/ RSSI Voltage Measurement Both the Low Battery (bits 5/23-18) and RSSI (bits 5/17-12) measurement circuits have a 6-bit A/D converter whose value may be read back via the SPI. The A/D's sample their voltages at a frequency equal to the internal SCF clock frequency divided by 128. The Low Battery Measurement A/D senses and divides by 2.5 the supply voltage (at Pin 23). Please note that the minimum Low Battery Detect (LBD) voltage is 2.7 V, since there is no guarantee that the device will operate below this value. The RSSI Measurement senses the voltage at Pin 37. 33 MC33411A/B These values are compared to the internal reference VB (1.5 V) which is available at Pin 37. The value read back from the LBD A/D will therefor be approximately: N(for LBD) 63 (V ) CC [ 2.5(VB)(1.07) VB Voltage Adjust and Characteristics VB has a production tolerance of 8%, and can be adjusted over a 9% range using bits 3/20-17. The adjustment steps will be 1.2% each (See Table 8). If desired, VB can be used to bias external circuitry, as long as the load current on this pin does not exceed 10 A. VB varies by less than 0.5% over supply voltage, referenced to VCC = 3.6 V. The value of the de-coupling capacitor connected from VB to ground affects both the noise and crosstalk from the receive and transmit audio paths, so the value should be chosen with caution. Figures 50 and 51 show this relationship. (27) and for the RSSI N(for RSSI) [ 63 (RSSIVoltage) (VB)(1.07) (28) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Table 8. VB Voltage Reference Programming Vref Adjust Bit #20 Vref Adjust Bit #19 Vref Adjust Bit #18 Vref Adjust Bit #17 Vref Adjust # Voltage Reference Adjustment Amount 0 0 0 0 0 -9.0% 0 0 0 1 1 -7.8% 0 0 1 0 2 -6.6% 0 0 1 1 3 -5.4% 0 1 0 0 4 -4.2% 0 1 0 1 5 -3.0% 0 1 1 0 6 -1.8% 0 1 1 1 7 -0.6% 1 0 0 0 8 0.6% 1 0 0 1 9 1.8% 1 0 1 0 10 3.0% 1 0 1 1 11 4.2% 1 1 0 0 12 5.4% 1 1 0 1 13 6.6% 1 1 1 0 14 7.8% 1 1 1 1 15 9.0% Figure 51. Crosstalk/Noise from E In to Tx Out versus VB Capacitor Figure 50. Crosstalk/Noise from C In to E Out versus VB Capacitor -105 -50 Crosstalk -92 -115 -97 -120 -102 VCC = 3.6 V TA = 25C -125 0.01 1.0 VB CAPACITOR (F) 34 -107 10 -63 -60 -65 Crosstalk, 130 load -65 -70 -67 -75 -80 -69 Crosstalk, no load -71 -85 -90 0.1 Noise -95 0.01 VCC = 3.6 V TA = 25C -73 0.1 1.0 -75 10 VB CAPACITOR (F) MOTOROLA RF/IF DEVICE DATA NOISE LEVEL @ Tx OUT (dBV) CROSSTALK (dB) -110 -61 -55 CROSSTALK (dB) -87 NOISE LEVEL @ E OUT (dBV) Noise MC33411A/B MCU Serial Interface The MCU Serial Interface is a 3-wire interface, consisting of a Clock line, an Enable line, and a bi-directional Data line. The interface is always active, i.e., it cannot be powered down as all other sections of the MC33411 are disabled and enabled through this interface. After the device power-up (or whenever a reset condition is required), the MCU should perform the following steps: 1. Initialize the Data line to a high impedance state. 2. Initialize the Clock line to a logic low. 3. Initialize the Enable line to a logic low. 4. Pulse the Clock line a minimum of once (RZ format) while leaving the Enable line continuously low. This places the SPI port into a known condition. The clock (Return-to-Zero format) must be supplied to the MC33411 at Pin 11 to write or read data, and can be any frequency up to 2.0 MHz. The clock need not be present when data is not being transferred. The Enable line must be low when data is not being transferred. Internally there are 7 data registers, 24-bits each, addressed with 4-bits ranging from $h1 to $h7 (see Tables 9 and 10). Register 5, bits 23-12 are read-only bits, while all other register bits are Read/Write. All unused/unimplemented bits are reserved for Motorola use only. The contents of the 7 registers can be read out at any time. All bits are written in, or read out, on the clock's positive transition. The write and read operations are as follows: 5. Load all registers with their desired initial values. Figure 52. Writing Data to the MC33411 1 2 3 24 Clock Data 4-Bit Address MSB LSB 24-Bit Data from MCU Latch Address Latch Data Enable a. Write Operation: - To write data to the MC33411, the following sequence is required (see Figure 52): 6. The Enable line is taken high. 7. Five bits are entered: - The first bit must be a 0 to indicate a Write operation. - The next four bits identify the register address (0001-0111). The MSB is entered first. 8. The Enable line is taken low. At this transition, the address is latched in and decoded. 9. The Enable line is maintained low while the data bits are clocked in. The MSB is entered first, and the LSB last. If 24-bits are written to a register which has less than 24 active bits (e.g., register 6), the unassigned bits are to be 0. MOTOROLA RF/IF DEVICE DATA 10. After the last bit is entered, the Enable line is to be taken high and then low. The falling edge of this pulse latches in the just entered data. The clock line must be at a logic low and must not transition in either direction during this Enable pulse. 11.The Enable line must then be kept low until the next communication. Note: If less than 24 bits are to be written to a data register, it is not necessary to enter the full 24 bits, as long as they are all lower order bits. For example, if bits 0-6 of a register are to be updated, they can be entered as 7 bits with 7 clock cycles in step 4 above. However, if this procedure is used, a minimum of 4 bits, with 4 clock pulses, must be entered. 35 MC33411A/B Figure 53. Reading Data from the MC33411 Sets Data Pin to Output 1 2 3 24 Clock Data 4-Bit Address Enable MSB Latch Address and Load Data into Shift Register b. Read Operation: - To read the output bits (bits 5/23-12), or the contents of any register, the following sequence is required (see Figure 53): 1. The Enable line is taken high. 2. Five bits are entered: - The first bit must be a 1 to indicate a Read operation. - The next four bits identify the register address (0001-0111). The MSB is entered first. 3. The Enable line is taken low. At this transition, the address is latched in and decoded, and the contents of the selected register is loaded into the 24-bit output shift register. At this point, the Data line (Pin 12) is still an input. 4. While maintaining the Enable line low, the data is read out. The first clock rising edge will change the Data line to an output, and the MSB will be present on this line. 5. The full contents of the register are then read out (MSB first, LSB last) with a total of 24 clock rising edges, including the one in step 4 above. It is recommended that the MCU read the bits after the clock's falling edge. 6. After the last clock pulse, the Enable line is to be taken high and then low. The falling edge of this pulse returns the Data Pin to be an input. The clock line must be at a logic low and must not transition in either direction during this Enable pulse. 7. The Enable line must then be kept low until the next communication. Power Supply/Power Saving Modes The power supply voltage, applied to all VCC pins, can range from 2.7 to 5.5 V. All VCC pins must be within 0.5 V of each other, and each must be bypassed. It is recommended a ground plane be used, and all leads to the MC33411 be as short and direct as possible. To reduce the possibility of device latch-up, it is highly recommended that the Audio, Synthesizer and RF VCC portions of the chip be isolated from the main supply through 10 to 25 resistors (see the Evaluation PCB Schematic, Figure 54). This also provides RF-to-Audio noise isolation. The supply and ground pins are distributed as follows: 1. Pin 23 provides power to the audio section. Pin 40 is the ground pin. 2. Pin 28 provides power to the speaker amplifier section. Pin 31 is the ground pin. 36 LSB 24-Bit Data from MC33411 Sets Data Pin to Input 3. Pin 3 provides power to the Rx PLL section. Pin 5 is the ground pin. 4. Pin 7 provides power to the Tx PLL section, and the MCU interface. Pin 5 is the ground pin. 5. Pin 42 provides power to the 2nd LO section. Pins 46 and 48 are the ground pins. 6. Pin 14 is the ground pin for the digital circuitry. Power for the digital circuitry is derived from Pin 23. To conserve power, various sections can be individually disabled by using bits 5/7-0 and 6/7 (setting a bit to 1 disables the section). 1. Reference Oscillator Disable (bit 5/0) - The reference oscillator at Pins 15 and 16 is disabled, thereby denying a clock to the three PLLs and the switched capacitor filters. This function is not available on the "B" version. 2. Tx PLL Disable (bit 5/1) - The 13-bit and 7-bit counters, input buffer, phase detector, and modulus control blocks are disabled. The charge pump output at Pin 6 will be in a Hi-Z state. 3. Rx PLL Disable (bit 5/2) - The 13-bit and 7-bit counters, input buffer, phase detector, and modulus control blocks are disabled. The charge pump output at Pin 4 will be in a Hi-Z state. 4. LO2 PLL Disable (bit 5/3) - The VCO, 14-bit counter, output buffer, and phase detector are disabled. The charge pump output at Pin 47 will be in a Hi-Z state. 5. Power Amplifier Disable (bit 5/4) - The two speaker amplifiers are disabled. Their outputs will go to a high impedance state. 6. Rx Audio Path Disable (bit 5/5) - The anti-aliasing filter, low-pass filter, and variable gain stage are disabled. 7. Tx Audio Path Disable (bit 5/6) - Disables the microphone amplifier and low-pass filter. 8. Low Battery/RSSI Measurement Disable (bit 5/7) - Both 6-bit A/Ds are disabled. 9. Data Slicer Disable (bit 5/8) - The data slicer is disabled and DS Out goes to high impedance. 10. MCU Clock Disable (bit 6/7) - The MCU clock counter is disabled and the MCU Clock Output will be in a Hi-Z state. This function is not available on the "B" version. Note: The 12-bit reference counter is disabled if the three PLLs are disabled (bits 5/1-3 = 1). MOTOROLA RF/IF DEVICE DATA MOTOROLA RF/IF DEVICE DATA 1 2 3 4 5 6 7 0001 0010 0011 0100 0101 0110 0111 MSB Bit 23 1 2 3 4 5 6 7 0001 0010 0011 0100 0101 0110 0111 Bit 20 0 0 0 1 1 0 0 0 1 1 0 0 Bit 13 Bit 12 2nd LO PD Cur Sel MSB 13-Bit Rx N' Counter Divide Value Bit 16 Bit 14 Bit 13 Bit 12 0 0 0 0 2nd LO PD Cur Sel 0 1 MSB 0 0 0 13-Bit Rx N' Counter Divide Value 0 13-Bit Tx N Counter Divide Value Bit 15 0 0 FTxMC/ LO2 FRxMC Polarity Mode Select 0 0 0 Volume Control ALC Gain ALC Gain = 25 = 10 0 6-Bit RSSI A/D Output 0 0 1 1 MCU Clock Divide Select 0 Data Slicer Invert Bit 9 0 0 1 0 1 1 Volume Control 0 1 0 0 Data Slicer Invert 0 0 0 0 Bit 9 MSB MSB Bit 6 Bit 5 0 1 LSB LSB 0 LSB 0 LSB Bit 7 1 MSB 1 MSB Bit 6 0 0 Bit 5 0 0 Bit 2 0 0 0 0 0 0 0 0 0 Bit 1 LSB 0 LSB 0 LSB 0 LSB LSB Bit 0 1 Tx Gain Adjust 1 1 0 1 1 Rx Gain Adjust 1 1 0 0 0 0 0 0 0 0 RSSI & Tx Audio Rx Audio Power 2nd LO Rx PLL Tx PLL Ref Osc Batt. A/D Disable Disable Amp PLL Disable Disable Disable Disable Disable Disable* 0 0 0 0 0 0 0 0 Expander Power MCU Clk ALC Limiter Compres- Pass- Pass- Tx Mute Rx Mute Amp Disable* Disable Disable ser through through Mute 0 0 0 0 0 0 0 0 0 0 7-Bit Rx A' Counter Divide Value 0 12-Bit Reference Counter Divide Value 0 Bit 3 7-Bit Tx A Counter Divide Value Bit 4 Rx Gain Adjust RSSI & 2nd LO Rx PLL Tx PLL Ref Osc Audio Rx Audio Power Batt. A/D Tx Amp PLL Disable Disable Disable Disable Disable Disable Disable Disable* Compres- Expander Power MCU Clk ALC Limiter Pass- Pass- Tx Mute Rx Mute Amp Disable* Disable Disable ser through through Mute 14-Bit 2nd LO Counter Divide Value 0 0 Bit 8 LSB Bit 0 LSB Bit 1 7-Bit Rx A' Counter Divide Value Bit 2 LSB Bit 3 7-Bit Tx A Counter Divide Value Bit 4 12-Bit Reference Counter Divide Value Tx Gain Adjust 0 Data Slicer Disable 0 Comp. Side Tone Max. Attenuate Select Low Gain En. 0 0 0 0 0 0 0 Bit 10 Unused Register Bits 0 0 ALC Gain ALC Gain = 25 = 10 0 MSB 0 0 0 Bit 11 LSB LSB Bit 7 14-Bit 2nd LO Counter Divide Value Bit 8 Data Slicer Disable Comp. Side Tone Max. Attenuate Select Low Gain En. Bit 10 Unused Register Bits MSB Bit 11 Table 10. Register Map: Power-Up Defaults MCU Clock Divide Select 6-Bit RSSI A/D Output 6-Bit Switched Capacitor Filter Counter Divide Value Bit 17 VB Voltage Reference Adjust 1 MSB 1 MSB Bit 19 LO2 Capacitor Select 0 Tx Tx PD Polarity Cur Sel Select 0 0 Rx Rx PD Polarity Cur Sel Select 0 0 Bit 21 6-Bit Battery Voltage A/D Output 0 Test Modes Bit 22 Bit 18 LO2 Capacitor Select Bit 14 13-Bit Tx N Counter Divide Value Bit 15 FTxMC/ LO2 FRxMC Polarity Mode Select Bit 16 6-Bit Switched Capacitor Filter Counter Divide Value Bit 17 Table 10. Register Map: Power-Up Defaults 0 MSB Bit 23 Bit 18 VB Voltage Reference Adjust MSB MSB Bit 19 Table 9. Register Map * These bits not included in "B" version. Reg Num Reg Add Bit 20 Tx Tx PD Polarity Cur Sel Select Rx Rx PD Polarity Cur Sel Select Bit 21 6-Bit Battery Voltage A/D Output Test Modes Bit 22 * These bits not included in "B" version. Reg Num Reg Add Table 9. Register Map MC33411A/B 37 38 H5X2 1 2 3 4 5 6 7 8 9 10 JP3 LO2 Ctl TP5 LO2 Out J16 AUD In J4 PA In TP4 E In TP3 FRx Rx MC Rx PD Det In RSSI RX EN R3 U/D C7 U/D C8 U/D R4 U/D L1 U/D R9 U/D C20 U/D J5 N/O C18 U/D C19 U/D R10 U/D C21 U/D R18 49.9 J15 N/C V CCL C40 0.01 C14 0.01 C6 1.0 C9 1.0 J6 N/C C10 1.0 V CCA 1.0 C12 C28 U/D 1 R x P D C29 0.01 2 3 4 P L F L R x F V M R C C x C R14 U/D R13 U/D C26 U/D V CCR LO2- LO2 Gnd LO2 PD LO2 Gnd C27 U/D 45 46 47 48 R x O u t P L L G n d 1 1 0 1 R12 U/D 1 2 C24 U/D C23 U/D C22 U/D R11 U/D C25 0.01 5 6 7 8 9 T x P D Mic Amp 24 VCC Audio 23 C In 22 C cap 21 C Out 20 Lim In 19 Tx Out 18 DS Out 17 Fref Out 16 Fref In 15 Gnd Digital 14 MCU Clk Out 13 P L F L T D C a V F x C T M E L t C x C N K a U1 MC33411 2 7 0.1 C38 4.7 C39 2 2 6 5 V V V M C B A C C G I P A 2 8 V CCA 3 3 3 3 3 3 2 5 4 3 2 1 0 9 E E E P G P P A n A A I c O I d O O n a u p t P - + A C12 1.0 3 6 R7 130 J8 N/O J7 N/C 37 RSSI In 38 Rx Audio In 39 DS In 40 Gnd Audio 41 LO2 Out 42 LO2 V CC 43 LO2+ 44 LO2 Ctl 47.5 k J26 N/C V CCL C13 220 p R5 47.5 k J25 N/C J27 N/O R6 R2 47.5 k C5 1.0 J24 N/O 1.0 C1 V CCA TP6 Lim In TP2 C In TP1 JP1 TP7 Gnd J18 Tx Out Tx DAT Tx PD Tx EN Tx MC FTx AAAA AAAA H5X2 1 2 3 4 5 6 7 8 9 10 JP2 H5X2 1 2 3 4 5 6 7 8 9 10 C30 10 Tx AUD J1 PA Out- J10 PA Out+ J9 VCCD J17 Tx DAT Tx EN Rx EN EN CLK Data CK Out DS Out C16 15 p Y1 10.24 M C15 15 p R8 49.9 U/D R20 V CCA VCCD C17 0.01 J12 N/C J13 N/O J11 N/C J3 N/C C4 0.47 C3 1.0 J2 N/C C2 220 p J23 N/C R1 47.5 k U/D R19 Figure 54. MC33411A/B Evaluation PCB Schematic F In J14 0.01 C31 D1 1N4001 C36 10 R17 10 C34 10 R16 10 C32 10 R15 10 V CCA V CCL C37 0.01 V CCR C35 0.01 C33 0.01 MC33411A/B Figure 54. MC33411A/B Evaluation PCB Schematic MOTOROLA RF/IF DEVICE DATA MC33411A/B Figure 55. MC33411A/B Evaluation PCB Component Side 4.5 4.5 C1,C3,C5,C6,C9,C10,C12 C13,C2 C4,C11 L1,R3,R4,C7,C8,R9,R10, R11,R12,R13,R14,C18,R19, C19,R20,C20,C21,C22,C23, C24,C26,C27,C28 C14,C17,C25,C29,C31,C33, C35,C37,C40 C15,C16 R15,R16,R17,C30,C32,C34, C36 C38 C39 D1 H1,H2,H3,H4 JP1,JP2,JP3 J1 J2,J3,J6,J7,J11,J12,J15, J23,J25,J26 J4 MOTOROLA RF/IF DEVICE DATA 1.0 220 p 0.47 User defined 0.01 15 p 10 4.7 0.1 1N4001 None H5X2 Tx Aud N.C. J5,J8,J13,J24,J27 J9 J10 J14 J16 J17,TP6 J18,TP7 J19,J20,J21,J22 R1,R2,R5,R6 R7 R8,R18 TP1 TP2 TP3 TP4 TP5 U1 Y1 N/O PAOUT+ PAOUT- F In LO2 Out VCCD Gnd TP 47.5 k 130 49.9 C In Lim In E In PA In LO2 Ctl MC33411 10.24 M Aud In 39 MC33411A/B Figure 56. MC33411A/B Evaluation PCB Solder Side 4.5 4.5 40 MOTOROLA RF/IF DEVICE DATA MC33411A/B OUTLINE DIMENSIONS FTA SUFFIX PLASTIC PACKAGE CASE 932-02 (LQFP-48) ISSUE D 4X 0.200 (0.008) AB T-U Z 9 DETAIL Y A P A1 48 37 1 36 -T- -U- B V AE B1 12 25 13 AE V1 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DATUM PLANE -AB- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4 DATUMS -T-, -U-, AND -Z- TO BE DETERMINED AT DATUM PLANE -AB-. 5 DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -AC-. 6 DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -AB-. 7 DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.350 (0.014). 8 MINIMUM SOLDER PLATE THICKNESS SHALL BE 0.0076 (0.0003). 9 EXACT SHAPE OF EACH CORNER IS OPTIONAL. 24 DIM A A1 B B1 C D E F G H J K M N P Q R S S1 V V1 W X -Z- S1 -T-, -U-, -Z- S DETAIL Y 4X 0.200 (0.008) AC T-U Z 0.080 (0.003) AC G -AB- -AC- AD INCHES MIN MAX 0.276 BSC 0.138 BSC 0.276 BSC 0.138 BSC 0.055 0.063 0.007 0.011 0.053 0.057 0.007 0.009 0.020 BASIC 0.002 0.006 0.004 0.008 0.020 0.028 12 _REF 0.004 0.006 0.010 BASIC 1_ 5_ 0.006 0.010 0.354 BSC 0.177 BSC 0.354 BSC 0.177 BSC 0.008 REF 0.039 REF M_ BASE METAL CCCC EEE CCCC EEE CCCC EEE MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.170 0.270 1.350 1.450 0.170 0.230 0.500 BASIC 0.050 0.150 0.090 0.200 0.500 0.700 12 _REF 0.090 0.160 0.250 BASIC 1_ 5_ 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF TOP & BOTTOM N R J GAUGE PLANE 0.250 (0.010) C E F D 0.080 (0.003) M AC T-U S SECTION AE-AE Z S W H Q_ K DETAIL AD X MOTOROLA RF/IF DEVICE DATA 41 MC33411A/B Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan. 81-3-5487-8488 Customer Focus Center: 1-800-521-6274 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 - http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ 44 MC33411A/D MOTOROLA RF/IF DEVICE DATA