CA5260, CA5260A S E M I C O N D U C T O R 3MHz, BiMOS Microprocessor Operational Amplifiers with MOSFET Input/CMOS Output November 1996 Features Description * MOSFET Input Stage provides - Very High ZI = 1.5T (1.5 x 1012) (Typ) - Very Low II = 5pA (Typ) at 15V Operation = 2pA (Typ) at 5V Operation The CA5260A and CA5260 are integrated-circuit operational amplifiers that combine the advantage of both CMOS and bipolar transistors on a monolithic chip. The CA5260 series circuits are dual versions of the popular CA5160 series. They are designed and guaranteed to operate in microprocessor or logic systems that use +5V supplies. * Ideal for Single Supply Applications * Common Mode Input Voltage Range Includes Negative Supply Rail; Input Terminals Can be Swung 0.5V Below Negative Supply Rail * CMOS Output Stage Permits Signal Swing to Either (or Both) Supply Rails * CA5260A, CA5260 Have Full Military Temperature Range Guaranteed Specifications for V+ = 5V * CA5260A, CA5260 are Guaranteed to Operate Down to 4.5V for AOL * Fully Guaranteed to Operate from -55oC to 125oC at V+ = 5V, V- = GND Gate-protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to provide very-high-input impedance, very-low-input current, and exceptional speed performance. The use of PMOS field-effect transistors in the input stage results in common-mode input-voltage capability down to 0.5V below the negative-supply terminal, an important attribute in single-supply applications. A complementary-symmetry MOS (CMOS) transistor-pair, capable of swinging the output voltage to within 10mV of either supply-voltage terminal (at very high values of load impedance), is employed as the output circuit. The CA5260 Series circuits operate at supply voltages ranging from 4.5V to 16V, or 2.25V to 8V when using split supplies. Applications The CA5260, CA5260A have guaranteed specifications for 5V operation over the full military temperature range of -55oC to 125oC. * Ground Referenced Single Supply Amplifiers * Fast Sample-Hold Amplifiers * Long Duration Timers/Monostables Ordering Information * Ideal Interface with Digital CMOS PART NUMBER (BRAND) * High Input Impedance Wideband Amplifiers * Voltage Followers (e.g., Follower for Single Supply D/A Converter) TEMP. RANGE (oC) PKG. NO. PACKAGE CA5260AE -55 to 125 8 Ld PDIP E8.3 CA5260AM (5260A) -55 to 125 8 Ld SOIC M8.15 * Wien Bridge Oscillators CA5260AM96 (5260A) -55 to 125 8 Ld SOIC Tape and Reel M8.15 * Voltage Controlled Oscillators CA5260E -55 to 125 8 Ld PDIP E8.3 CA5260M (5260) -55 to 125 8 Ld SOIC M8.15 CA5260M96 (5260) -55 to 125 8 Ld SOIC Tape and Reel M8.15 * Voltage Regulators (Permits Control of Output Voltage Down to 0V) * Photo Diode Sensor Amplifiers * 5V Logic Systems * Microprocessor Interface Pinout CA5260 (PDIP, SOIC) TOP VIEW OUTPUT (A) 1 8 V+ 7 OUTPUT (B) 6 INV. INPUT (B) 5 NON INV. INPUT (B) A INV. INPUT (A) 2 - + B NON INV. INPUT (A) 3 V- 4 + - CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) Harris Corporation 1996 3-146 File Number 1929.3 CA5260, CA5260A Absolute Maximum Ratings Thermal Information Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . . 16V Differential Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . (V+ +8V) to (V- -0.5V) Input Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA Output Short Circuit Duration (Note 1) . . . . . . . . . . . . . . . . Indefinite Thermal Resistance (Typical, Note 2) JA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Maximum Junction Temperature (Die). . . . . . . . . . . . . . . . . . . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Short circuit may be applied to ground or to either supply. 2. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Typical Values Intended Only for Design Guidance, V+ = 5V, V- = 0V, TA = 25C, Unless Otherwise Specified TYPICAL VALUES PARAMETER SYMBOL Input Resistance RI CI Input Capacitance Unity Gain Crossover Frequency fT Slew Rate SR Transient Response Rise Time tr Overshoot PARAMETER CA5260 tS UNITS 1.5 1.5 T 4.3 pF 3 3 MHz 5 5 V/s 0.09 0.09 s 10 10 % 1.8 1.8 s VOUT = 2.5VP-P CL = 25pF, RL = 2k (Voltage Follower) CA5260A 4.3 f = 1MHz OS Settling Time (To <0.1%, VIN = 4VP-P) Electrical Specifications TEST CONDITIONS CL = 25pF, RL = 2k (Voltage Follower) TA = 25oC, V+ = 5V, V- = 0V CA5260 CA5260A MIN TYP MAX MIN TYP MAX UNITS Input Offset Voltage VIO VO = 2.5V - 2 15 - 1.5 4 mV Input Offset Current IIO VO = 2.5V - 1 10 - 1 10 pA II VO = 2.5V - 2 15 - 2 15 pA Input Current Common Mode Rejection Ratio SYMBOL TEST CONDITIONS CMRR VCM = 0 to 1V 70 85 - 80 85 - dB VCM = 0 to 2.5V 50 55 - 50 55 - dB Common Mode Input Voltage Range VlCR+ 2.5 3 - 2.5 3 - V VlCR- - -0.5 0 - -0.5 0 V Power Supply Rejection Ratio PSRR Large Signal Voltage Gain (Note 3) Source Current AOL V+ = 1V; V- = 1V 70 84 - 75 84 - dB RL = , VO = 0.5 to 4V 105 111 - 107 113 - dB 80 86 - 83 86 - dB RL = 10k, VO = 0.5 to 3.6V ISOURCE VO = 0V 1.75 2.2 - 1.75 2.2 - mA Sink Current ISINK VO = 5V 1.70 2 - 1.70 2 - mA Output Voltage VOM+ RL = 4.99 5 - 4.99 5 - V - 0 0.01 - 0 0.01 V 4.4 4.7 - 4.4 4.7 - V - 0 0.01 - 0 0.01 V 3 3.4 - 3 3.4 - V - 0 0.01 - 0 0.01 V VOMVOM+ RL = 10k VOMVOM+ RL = 2k VOM- 3-147 CA5260, CA5260A Electrical Specifications PARAMETER Supply Current TA = 25oC, V+ = 5V, V- = 0V (Continued) SYMBOL ISUPPLY CA5260 TEST CONDITIONS CA5260A MIN TYP MAX MIN TYP MAX UNITS VO = 0V - 1.60 2.0 - 1.60 2.0 mA VO = 2.5V - 1.80 2.25 - 1.80 2.25 mA NOTE: 3. For V+ = 4.5V and V- = GND; VOUT = 0.5V to 3.2V at RL = 10k. Electrical Specifications PARAMETER TA = -55oC to 125oC, V+ = 5V, V- = 0V SYMBOL CA5260 TEST CONDITIONS CA5260A MIN TYP MAX MIN TYP MAX UNITS Input Offset Voltage VIO VO = 2.5V - 3 20 - 2 15 mV Input Offset Current IIO VO = 2.5V - 1 10 - 1 10 nA II VO = 2.5V - 2 15 - 2 15 nA 60 78 - 65 78 - dB Input Current Common Mode Rejection Ratio CMRR VCM = 0 to 1V 50 60 - 50 60 - dB Common Mode Input Voltage Range VlCR+ 2.5 3 - 2.5 3 - V VlCR- - -0.5 0 - -0.5 0 V Power Supply Rejection Ratio PSRR 60 65 - 62 65 - dB 70 78 - 70 78 - dB RL = 10k, VO = 0.5 to 3.6V 60 65 - 60 65 - dB VCM = 0 to 2.5V Large Signal Voltage Gain (Note 4) Source Current AOL V+ = 1V; V- = 1V RL = , VO = 0.5 to 4V ISOURCE VO = 0V 1.3 1.6 - 1.3 1.6 - mA Sink Current ISINK VO = 5V 1.2 1.4 - 1.2 1.4 - mA Output Voltage VOM+ RL = 4.99 5 - 4.99 5 - V - 0 0.01 - 0 0.01 V 4.2 4.4 - 4.2 4.4 - V - 0 0.01 - 0 0.01 V 2.5 2.7 - 2.5 2.7 - V - 0 0.01 - 0 0.01 V VOMVOM+ RL = 10k VOMVOM+ RL = 2k VOMSupply Current ISUPPLY VO = 0V - 1.65 2.2 - 1.65 2.2 mA VO = 2.5V - 1.95 2.35 - 1.95 2.35 mA NOTE: 4. For V+ = 4.5V and V- = GND; VOUT = 0.5V to 3.2V at RL = 10k. Electrical Specifications PARAMETER Each Amplifier at TA = 25oC, V+ = 15V, V- = 0V, Unless Otherwise Specified CA5260 CA5260A MIN TYP MAX MIN TYP MAX UNITS Input Offset Voltage VIO VS = 7.5 - 6 15 - 2 5 mV Input Offset Current IIO VS = 7.5 - 0.5 30 - 0.5 20 pA II VS = 7.5 Input Current Large Signal Voltage Gain Common Mode Rejection Ratio SYMBOL TEST CONDITIONS AOL CMRR VO = 10VP-P, RL = 10k - 5 50 - 5 30 pA 50 320 - 50 320 - kV/V 94 110 - 94 110 - dB 70 90 - 80 95 - dB 3-148 CA5260, CA5260A Electrical Specifications PARAMETER Each Amplifier at TA = 25oC, V+ = 15V, V- = 0V, Unless Otherwise Specified (Continued) CA5260 TEST CONDITIONS SYMBOL CA5260A MIN TYP MAX MIN TYP MAX UNITS 10 -0.5 to 12 0 10 -0.5 to 12 0 V Common Mode Input Voltage Range VlCR Power Supply Rejection Ratio, VIO/ V PSRR VS = 7.5 - 32 320 - 32 150 V/V Maximum Output Voltage VOM+ RL = 10k 11 13.3 - 11 13.3 - V - 0.002 0.01 - 0.002 0.01 V 14.99 15 - 14.99 15 - V VOMRL = VOM+ VOMIOM+ (Source) Maximum Output Current VO = 7.5V IOM- (Sink) Total Supply Current, RL = I+ - 0 0.01 - 0 0.01 V 12 22 45 12 22 45 mA 12 20 45 12 20 45 mA VO (Amp A) = 7.5V VO (Amp B) = 7.5V - 9 16.5 - 9 16.5 mA VO (Amp A) = 0V VO (Amp B) = 0V - 1.2 4 - 1.2 4 mA VO (Amp A) = 0V VO (Amp B) = 7.5V - 5 9.5 - 5 9.5 mA - 8 - - 6 - V/oC - 120 - - 120 - dB VIO/T Input Offset Voltage Temperature Drift Crosstalk f = 1kHz Schematic Diagram V+ 8 AMPLIFIER A Q11 Q7 Q6 Q10 D2 Q13 Q14 C3 D4 R5 2K Q22 Q8 C1 30pF R4 1K R3 1K D5 R12 2K Q24 D8 Q16 Q15 C2 30pF R11 1K R2 1K R9 1K Q26 R10 Q27 1K Q18 Q4 R1 1K Q25 D7 Q19 Q5 Q3 R7 300K Q20 D6 Q1 Q2 Q12 Q21 Q23 Q9 D3 D1 R6 200K AMPLIFIER B Q17 Q28 C4 R13 200K R14 300 R8 1K 3 2 1 7 6 5 4 +IN -IN OUT -IN +IN V- 3-149