LS150 SPECIFICATIONS
PA579-01-01A
ITEMS LS150-5 LS150-12 LS150-15 LS150-24
1 Nominal Output Voltage V 3.3 5 12 15 24 36 48
2 A 30 26 12.5 10 6.5 4.3 3.3
3 Maximum Output Power W 99 130 150 150 156 154.8 158.4
4 Efficiency (Typ) (230VAC) ( * 1 ) % 75 79 83 85 86 87 87
5 Input Voltage Range ( * 2 )
6 Input Current (Typ)
(
115/230VAC) ( * 1 ) A
7 Inrush Current (Typ) ( * 3 )
8 Harmonic Current (230VAC) ( * 1 )
9 Output Voltage Range V 3 ~ 3.6 4.75 ~ 5.5 10.8 ~ 13.2 13.5 ~ 16.5 22 ~ 27.2 32 ~ 40 42 ~ 54
10 Ripple and Noise ( * 1, 4 mV 80 80 120 120 120 150 200
11 Line Regulation ( * 5, 6 ) mV 20 20 48 60 96 144 192
12 Load Regulation ( * 5, 7 ) mV 40 40 96 120 192 288 384
13 Temperature Coefficient
14 Over Current Protection ( * 8 ) A
15 Over Voltage Protection ( * 9 ) V 3.8 ~ 4.45 5.75 ~ 6.75 13.8 ~ 16.2 17.25 ~ 20.25 27.6 ~ 32.4 41.4 ~ 48.6 55.2 ~ 64.8
16 Hold-Up Time (Typ)
(
115/230VAC) ( * 1 ) mS
17 Leakage current ( * 10 )
18 Series Operation
19 Operating Temperature ( * 11 )
20 Operating Humidity
21 Storage Temperature
22 Storage Humidity
23 Cooling
24 Withstand Voltage
25 Isolation Resistance
26 Vibration
27 Shock (In package)
28 Safety
29 EMI
30 Immunity
31 Weight (Typ) g
32 Dimension (L x W x H) mm
* Read instruction manual carefully , before using the power supply unit.
= NOTES=
* 1 : At Maximum Output Power, nominal input voltage, Ta = 25°C.
* 2 : For cases where conformance to various safety specs ( UL, CSA, EN ) are required, to be described as 100 - 240VAC, 50 / 60Hz on name plate.
* 3 : Not applicable for the in-rush current to Noise Filter for less than 0.2mS.
* 4 : Ripple & noise are measured at 20MHz by using a 300mm twisted pair of load wires terminated with a 0.1uF film capacitor and a 47uF electrolytic capacitor.
* 5 : Measure line & load regulation at output terminal M3.5 tapped point.
* 6 : 88 ~ 132VAC or 176 ~ 264VAC, constant load.
* 7 : No load - Full load (Maximum power ), constant input voltage.
* 8 : Current limit with automatic recovery.
Avoid to operate at overload or dead short for more than 30 seconds.
* 9 : OVP circuit will shutdown output, manual reset (Re-power on).
* 10: Measured by each measuring method of UL and EN (at 60Hz), Ta=25°C.
* 11: Refer to Output Derating Curve (PA579-01-02_) for details of output derating versus ambient temperature and mounting method.
* 12: All parameters NOT specifically mentioned are measured at 115/230VAC input, rated load and Ta = 25oC.
LS150-3.3 LS150-48LS150-36
DENSEI-LAMBDA
40A at 230VAC, Ta=25°C (Cold Start)
Maximum Output Current
3.5 / 2.0
88 ~ 132VAC / 176 ~ 264VAC (47-63Hz) Input Selectable or 248 ~ 373VDC
(Withstand 300VAC Surge for 5 seconds)
Built to meet IEC61000-3-2, -3
Less than 0.02%/°C
25 / 30
< 1mA at 230VAC, 60Hz
20 ~ 90 %RH (No dewdrop)
- 40 ~ +85°C
10 ~ 95%RH (No dewdrop)
Convection cooling
199 x 98 x 38 (Refer to Outline Drawing)
Approved by UL60950-1, EN60950-1, IEC60950-1
Built to meet EN55011/EN55022-B, FCC-B
Built to meet EN61000-4-2 (Level 2,3), -3 (Level 3), -4 (Level 3),
-5 (Level 4), -6 (Level 3), -8 (Level 4), -11
Possible
- 25 ~ + 70 °C (Refer to Output Derating Curve)
> 110% rated output power
700
Input - Output : 3.0kVAC (20mA), Input - FG : 1.5kVAC (20mA)
Output - FG : 500VAC (100mA) for 1min.
Input - FG, Input - Output and Output - FG: More than 100MΩ (500VDC) at 25oC and 70%RH
At no operating, 10 - 55Hz (sweep for 1min)
Less than 196.1m/s2
19.6m/s2 Constant, X, Y, Z 1hour each.
MODEL