410-286P - Digilent - Datasheet.Directory

3 4

VACS

GND SDATA

VIN SCLK

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

ADC081S021 Single Channel, 50 to 200 ksps, 8-Bit A/D Converter

Check for Samples: ADC081S021

1FEATURES DESCRIPTION

The ADC081S021 is a low-power, single channel

2• Specified Over a Range of sample Rates. CMOS 8-bit analog-to-digital converter with a high-

• 6-lead WSON and SOT-23 Packages speed serial interface. Unlike the conventional

• Variable Power Management practice of specifying performance at a single sample

rate only, the ADC081S021 is fully specified over a

• Single Power Supply with 2.7V - 5.25V Range sample rate range of 50 ksps to 200 ksps. The

• SPI™/QSPI™/MICROWIRE/DSP Compatible converter is based upon a successive-approximation

KEY SPECIFICATIONS circuit.

• DNL: +0.04/-0.03 LSB (typ) The output serial data is straight binary, and is

• INL: +0.04/-0.03 LSB (typ) compatible with several standards, such as SPI,

QSPI, MICROWIRE, and many common DSP serial

• SNR: 49.6 dB (typ) interfaces.

• Power Consumption The ADC081S021 operates with a single supply that

– 3.6V Supply: 1.3 mW (typ) can range from +2.7V to +5.25V. Normal power

– 5.25V Supply: 7.7 mW (typ) consumption using a +3.6V or +5.25V supply is 1.3

mW and 7.7 mW, respectively. The power-down

APPLICATIONS feature reduces the power consumption to as low as

2.6 µW using a +5.25V supply.

• Portable Systems The ADC081S021 is packaged in 6-lead WSON and

• Remote Data Acquisition SOT-23 packages. Operation over the industrial

• Instrumentation and Control Systems temperature range of −40°C to +85°C is ensured.

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Pin-Compatible Alternatives by Resolution and Speed(1)

Resolution Specified for Sample Rate Range of:

50 to 200 ksps 200 to 500 ksps 500 ksps to 1 Msps

12-bit ADC081S021121S021 ADC081S021121S051 ADC081S021121S101

10-bit ADC081S021101S021 ADC081S021101S051 ADC081S021101S101

8-bit ADC081S021 ADC081S021081S051 ADC081S021081S101

(1) All devices are fully pin and function compatible.

Connection Diagram

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

T/H

8-BIT

SUCCESSIVE

APPROXIMATION

ADC

SCLK

SDATA

CONTROL

LOGIC

VIN

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

Block Diagram

PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS

Pin No. Symbol Description

ANALOG I/O

3 VIN Analog input. This signal can range from 0V to VA.

DIGITAL I/O

4 SCLK Digital clock input. This clock directly controls the conversion and readout processes.

5 SDATA Digital data output. The output samples are clocked out of this pin on falling edges of the SCLK pin.

6 CS Chip select. On the falling edge of CS, a conversion process begins.

POWER SUPPLY

Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and bypassed to

1 VAGND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within 1 cm of the power pin.

2 GND The ground return for the supply and signals.

PAD GND For package suffix CISD(X) only, it is recommended that the center pad should be connected to ground.

Absolute Maximum Ratings(1)(2)(3)

Analog Supply Voltage VA−0.3V to 6.5V

Voltage on Any Analog Pin to GND −0.3V to (VA+0.3V)

Voltage on Any Digital Pin to GND −0.3V to 6.5V

Input Current at Any Pin(4) ±10 mA

Package Input Current(4) ±20 mA

Power Consumption at TA= 25°C See (5)

ESD Susceptibility(6) Human Body Model 3500V

Machine Model 300V

Junction Temperature +150°C

Storage Temperature −65°C to +150°C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.

(3) If Military/Aerospace specified devices are required, please contact the TI Office/Distributors for availability and specifications.

(4) When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to

10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an

input current of 10 mA to two. The Absolute Maximum Rating specification does not apply to the VApin. The current into the VApin is

limited by the Analog Supply Voltage specification.

(5) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by

TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula

PDMAX = (TJmax −TA)/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in

a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is

reversed). Obviously, such conditions should always be avoided.

(6) Human body model is 100 pF capacitor discharged through a 1.5 kΩresistor. Machine model is 220 pF discharged through zero ohms

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

Operating Ratings(1)(2)

Operating Temperature Range −40°C ≤TA≤+85°C

VASupply Voltage +2.7V to +5.25V

Digital Input Pins Voltage Range (regardless of supply voltage) −0.3V to 5.25V

Analog Input Pins Voltage Range 0V to VA

Clock Frequency 25 kHz to 20 MHz

Sample Rate up to 1Msps

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.

Package Thermal Resistance(1)

Package θJA

6-lead WSON 94°C / W

6-lead SOT-23 265°C / W

(1) Soldering process must comply with Texas Instruments' Reflow Temperature Profile specifications. Refer to http://www.ti.com/packaging

Reflow temperature profiles are different for lead-free and non-lead-free packages.

Product Folder Links: ADC081S021

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

ADC081S021 Converter Electrical Characteristics(1)(2)

The following specifications apply for VA= +2.7V to 5.25V, fSCLK = 1 MHz to 4 MHz, fSAMPLE = 50 ksps to 200 ksps, CL= 15

pF, unless otherwise noted. Boldface limits apply for TA= TMIN to TMAX: all other limits TA= 25°C.

Symbol Parameter Conditions Typical Limits(2) Units

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes 8Bits

VA= +2.7V to +3.6V ±0.03 ±0.3 LSB (max)

INL Integral Non-Linearity +0.04 LSB (max)

VA= +4.75V to +5.25V ±0.3

−0.03 LSB (min)

VA= +2.7V to +3.6V ±0.03 ±0.2 LSB (max)

DNL Differential Non-Linearity +0.04 LSB (max)

VA= +4.75V to +5.25V ±0.2

−0.03 LSB (min)

VA= +2.7V to +3.6V −0.01 ±0.2 LSB (max)

VOFF Offset Error VA= +4.75V to +5.25V +0.03 ±0.2 LSB (max)

VA= +2.7V to +3.6V +0.04 ±0.4 LSB (max)

GE Gain Error VA= +4.75V to +5.25V +0.1 ±0.4 LSB (max)

+0.055 LSB (max)

VA= +2.7V to +3.6V ±0.3

−0.065 LSB (min)

TUE Total Unadjusted Error +0.03 LSB (max)

VA= +4.75V to +5.25V ±0.3

−0.06 LSB (min)

DYNAMIC CONVERTER CHARACTERISTICS

VA= +2.7 to 5.25V

SINAD Signal-to-Noise Plus Distortion Ratio 49.5 49 dBFS (min)

fIN = 100 kHz, −0.02 dBFS

VA= +2.7 to 5.25V

SNR Signal-to-Noise Ratio 49.6 49 dBFS (min)

fIN = 100 kHz, −0.02 dBFS

VA= +2.7 to 5.25V

THD Total Harmonic Distortion −77 −65 dBFS (max)

fIN = 100 kHz, −0.02 dBFS

VA= +2.7 to 5.25V

SFDR Spurious-Free Dynamic Range 68 65 dBFS (min)

fIN = 100 kHz, −0.02 dBFS

VA= +2.7 to 5.25V

ENOB Effective Number of Bits 7.9 7.8 Bits (min)

fIN = 100 kHz, −0.02 dBFS

Intermodulation Distortion, Second VA= +5.25V −83 dBFS

Order Terms fa= 103.5 kHz, fb= 113.5 kHz

IMD Intermodulation Distortion, Third Order VA= +5.25V −82 dBFS

Terms fa= 103.5 kHz, fb= 113.5 kHz

VA= +5V 11 MHz

FPBW -3 dB Full Power Bandwidth VA= +3V 8 MHz

ANALOG INPUT CHARACTERISTICS

VIN Input Range 0 to VAV

IDCL DC Leakage Current ±1 µA (max)

Track Mode 30 pF

CINA Input Capacitance Hold Mode 4 pF

DIGITAL INPUT CHARACTERISTICS

VA= +5.25V 2.4 V (min)

VIH Input High Voltage VA= +3.6V 2.1 V (min)

VA= +5V 0.8 V (max)

VIL Input Low Voltage VA= +3V 0.4 V (max)

IIN Input Current VIN = 0V or VA±0.1 ±1 µA (max)

CIND Digital Input Capacitance 2 4pF (max)

(1) Tested limits are ensured to TI's AOQL (Average Outgoing Quality Level).

(2) Data sheet min/max specification limits are specified by design, test, or statistical analysis.

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

ADC081S021 Converter Electrical Characteristics(1)(2) (continued)

The following specifications apply for VA= +2.7V to 5.25V, fSCLK = 1 MHz to 4 MHz, fSAMPLE = 50 ksps to 200 ksps, CL= 15

pF, unless otherwise noted. Boldface limits apply for TA= TMIN to TMAX: all other limits TA= 25°C.

Symbol Parameter Conditions Typical Limits(2) Units

DIGITAL OUTPUT CHARACTERISTICS

ISOURCE = 200 µA VA−0.07 VA−0.2 V (min)

VOH Output High Voltage ISOURCE = 1 mA VA−0.1 V

ISINK = 200 µA 0.03 0.4 V (max)

VOL Output Low Voltage ISINK = 1 mA 0.1 V

IOZH, IOZL TRI-STATE Leakage Current ±0.1 ±10 µA (max)

COUT TRI-STATE Output Capacitance 2 4pF (max)

Output Coding Straight (Natural) Binary

POWER SUPPLY CHARACTERISTICS

2.7 V (min)

VASupply Voltage 5.25 V (max)

VA= +5.25V, 1.47 2.2 mA (max)

fSAMPLE = 200 ksps

Supply Current, Normal Mode

(Operational, CS low) VA= +3.6V, 0.36 0.9 mA (max)

fSAMPLE = 200 ksps

IAfSCLK = 0 MHz, VA= +5.25V 500 nA

fSAMPLE = 0 ksps

Supply Current, Shutdown (CS high) VA= +5.25V, fSCLK = 4 MHz, 60 µA

fSAMPLE = 0 ksps

VA= +5.25V 7.7 11.6 mW (max)

Power Consumption, Normal Mode

(Operational, CS low) VA= +3.6V 1.3 3.24 mW (max)

fSCLK = 0 MHz, VA= +5.25V

PD2.6 µW

fSAMPLE = 0 ksps

Power Consumption, Shutdown (CS

high) fSCLK = 4 MHz, VA= +5.25V, 315 µW

fSAMPLE = 0 ksps

AC ELECTRICAL CHARACTERISTICS

1.0 MHz (min)

fSCLK Clock Frequency See(3) 4.0 MHz (max)

50 ksps (min)

fSSample Rate See(3) 200 ksps (max)

SCLK Falling

tHOLD Hold Time 13 Edges

40 % (min)

DC SCLK Duty Cycle fSCLK = 4 MHz 50 60 % (max)

tACQ Minimum Timre Required for Acquisition 350 ns (max)

tQUIET See(4) 50 ns (min)

tAD Aperture Delay 3 ns

tAJ Aperture Jitter 30 ps

(3) This is the frequency range over which the electrical performance is ensured. The device is functional over a wider range which is

specified under Operating Ratings.

(4) Minimum Quiet Time required by bus relinquish and the start of the next conversion.

Product Folder Links: ADC081S021

IOL

200 PA

IOH

200 PA

1.6 V

To Output Pin CL

25 pF

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

ADC081S021 Timing Specifications

The following specifications apply for VA= +2.7V to 5.25V, GND = 0V, fSCLK = 1.0 MHz to 4.0 MHz, CL= 25 pF, fSAMPLE = 50

ksps to 200 ksps, Boldface limits apply for TA= TMIN to TMAX: all other limits TA= 25°C.

Symbol Parameter Conditions Typical Limits Units

tCS Minimum CS Pulse Width 10 ns (min)

tCSSU CS Setup Time prior to SCLK Falling Edge(1) 10 ns (min)

tCSH CS Hold Time after SCLK Falling Edge(1) 1ns (min)

tEN Delay from CS Until SDATA TRI-STATE Disabled(2) 20 ns (max)

VA= +2.7V to +3.6V 40 ns (max)

tACC Data Access Time after SCLK Falling Edge(3) VA= +4.75V to +5.25V 20 ns (max)

tCL SCLK Low Pulse Width 0.4 x tSCLK ns (min)

tCH SCLK High Pulse Width 0.4 x tSCLK ns (min)

VA= +2.7V to +3.6V 7ns (min)

tHSCLK to Data Valid Hold Time VA= +4.75V to +5.25V 5ns (min)

25 ns (max)

VA= +2.7V to +3.6V 6ns (min)

tDIS SCLK Falling Edge to SDATA High Impedance(4) 25 ns (max)

VA= +4.75V to +5.25V 5ns (min)

tPOWER- Power-Up Time from Full Power-Down 1 µs

(1) Data sheet min/max specification limits are specified by design, test, or statistical analysis.

(2) Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V.

(3) Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V or 2.0V.

(4) tDIS is derived from the time taken by the outputs to change by 0.5V with the timing test circuit shown in Figure 1. The measured number

is then adjusted to remove the effects of charging or discharging the output capacitance. This means that tDIS is the true bus relinquish

time, independent of the bus loading.

Timing Diagrams

Figure 1. Timing Test Circuit

Product Folder Links: ADC081S021

tCSH

SCLK

tCSSU

1 2

Z2 Z1 Z0 DB7 Zero Zero Zero Zero

tQUIET

Track

3 leading zero bits 8 data bits

SCLK

SDATA

1 2 3 4 5 12 13 14 15 16

TRI-STATE

tSU tCL

tEN tCH tACC tHtDIS

tCS

Hold

tACQ

17 18 19 20

4 trailing zeroes

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

Figure 2. ADC081S021 Serial Timing Diagram

Figure 3. SCLK and CS Timing Parameters

Specification Definitions

ACQUISITION TIME is the time required to acquire the input voltage. That is, it is time required for the hold

capacitor to charge up to the input voltage. Acquisition time is measured backwards from the falling edge

of CS when the signal is sampled and the part moves from track to hold. The start of the time interval that

contains TACQ is the 13th rising edge of SCLK of the previous conversion when the part moves from hold

to track. The user must ensure that the time between the 13th rising edge of SCLK and the falling edge of

the next CS is not less than TACQ to meet performance specifications.

APERTURE DELAY is the time after the falling edge of CS when the input signal is acquired or held for

conversion.

APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample.

Aperture jitter manifests itself as noise in the output.

CONVERSION TIMEis the time required, after the input voltage is acquired, for the ADC081S021 to convert the

input voltage to a digital word. This is from the falling edge of CS when the input signal is sampled to the

16th falling edge of SCLK when the SDATA output goes into TRI-STATE.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1

LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital waveform is high to the total time of one period. The

specification here refers to the SCLK.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise

and Distortion or SINAD. ENOB is defined as (SINAD −1.76) / 6.02 and says that the converter is

equivalent to a perfect ADC081S021 of this (ENOB) number of bits.

FULL POWER BANDWIDTHis a measure of the frequency at which the reconstructed output fundamental drops

3 dB below its low frequency value for a full scale input.

GAIN ERRORis the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF −1 LSB),

after adjusting for offset error.

INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from

Product Folder Links: ADC081S021

AA++A

log20=THD 

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last

code transition). The deviation of any given code from this straight line is measured from the center of that

code value.

INTERMODULATION DISTORTION (IMD)is the creation of additional spectral components as a result of two

sinusoidal frequencies being applied to the ADC081S021 input at the same time. It is defined as the ratio

of the power in the second and third order intermodulation products to the sum of the power in both of the

original frequencies. IMD is usually expressed in dB.

MISSING CODES are those output codes that will never appear at the ADC081S021 outputs. The ADC081S021

is ensured not to have any missing codes.

OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND +

1 LSB).

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms

value of the sum of all other spectral components below one-half the sampling frequency, not including

harmonics or d.c.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of

the input signal to the rms value of all of the other spectral components below half the clock frequency,

including harmonics but excluding d.c.

SPURIOUS FREE DYNAMIC RANGE (SFDR)is the difference, expressed in dB, between the desired signal

amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral

component is any signal present in the output spectrum that is not present at the input and may or may

not be a harmonic.

TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB or dBc, of the rms total of the first five

harmonic components at the output to the rms level of the input signal frequency as seen at the output.

THD is calculated as where Af1 is the RMS power of the input

frequency at the output and Af2 through Af6 are the RMS power in the first 5 harmonic frequencies.

THROUGHPUT TIME is the minimum time required between the start of two successive conversion. It is the

acquisition time plus the conversion time.

TOTAL UNADJUSTED ERROR is the worst deviation found from the ideal transfer function. As such, it is a

comprehensive specification which includes full scale error, linearity error, and offset error.

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

Typical Performance Characteristics

TA= +25°C, fSAMPLE = 50 ksps to 200 ksps,fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated.

DNL INL

fSCLK = 1 MHz fSCLK = 1 MHz

Figure 4. Figure 5.

DNL INL

fSCLK = 4 MHz fSCLK = 4 MHz

Figure 6. Figure 7.

DNL INL

vs. vs.

Clock Frequency Clock Frequency

Figure 8. Figure 9.

Product Folder Links: ADC081S021

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

Typical Performance Characteristics (continued)

TA= +25°C, fSAMPLE = 50 ksps to 200 ksps,fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated.

Total Unadjusted Error

vs. SNR

Clock Frequency vs.

VA= 3.0V or 5.0V Clock Frequency

Figure 10. Figure 11.

SINAD SFDR

vs. vs.

Clock Frequency Clock Frequency

Figure 12. Figure 13.

THD

vs. Spectral Response, VA= 5V

Clock Frequency fSCLK = 1 MHz

Figure 14. Figure 15.

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

Typical Performance Characteristics (continued)

TA= +25°C, fSAMPLE = 50 ksps to 200 ksps,fSCLK = 1 MHz to 4 MHz, fIN = 100 kHz unless otherwise stated.

Power Consumption

vs.

Spectral Response, VA= 5V Throughput,

fSCLK = 4 MHz fSCLK = 4 MHz

Figure 16. Figure 17.

Product Folder Links: ADC081S021

GND

SAMPLING

CAPACITOR

SW1 -

+CONTROL

LOGIC

CHARGE

REDISTRIBUTION

DAC

SW2

VIN

GND

SAMPLING

CAPACITOR

SW1 -

+CONTROL

LOGIC

CHARGE

REDISTRIBUTION

DAC

SW2

VIN

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

APPLICATIONS INFORMATION

ADC081S021 OPERATION

The ADC081S021 is a successive-approximation analog-to-digital converter designed around a charge-

redistribution digital-to-analog converter core. Simplified schematics of the ADC081S021 in both track and hold

modes are shown in Figure 18 and Figure 19, respectively. In Figure 18, the device is in track mode: switch SW1

connects the sampling capacitor to the input, and SW2 balances the comparator inputs. The device is in this

state until CS is brought low, at which point the device moves to hold mode.

Figure 19 shows the device in hold mode: switch SW1 connects the sampling capacitor to ground, maintaining

the sampled voltage, and switch SW2 unbalances the comparator. The control logic then instructs the charge-

redistribution DAC to add or subtract fixed amounts of charge from the sampling capacitor until the comparator is

balanced. When the comparator is balanced, the digital word supplied to the DAC is the digital representation of

the analog input voltage. The device moves from hold mode to track mode on the 13th rising edge of SCLK.

Figure 18. ADC081S021 in Track Mode

Figure 19. ADC081S021 in Hold Mode

USING THE ADC081S021

The serial interface timing diagram for the ADC is shown in Figure 2. CS is chip select, which initiates

conversions on the ADC and frames the serial data transfers. SCLK (serial clock) controls both the conversion

process and the timing of serial data. SDATA is the serial data out pin, where a conversion result is found as a

serial data stream.

Basic operation of the ADC begins with CS going low, which initiates a conversion process and data transfer.

Subsequent rising and falling edges of SCLK will be labelled with reference to the falling edge of CS; for

example, "the third falling edge of SCLK" shall refer to the third falling edge of SCLK after CS goes low.

At the fall of CS, the SDATA pin comes out of TRI-STATE and the converter moves from track mode to hold

mode. The input signal is sampled and held for conversion on the falling edge of CS. The converter moves from

hold mode to track mode on the 13th rising edge of SCLK (see Figure 2). It is at this point that the interval for the

TACQ specification begins. At least 350ns must pass between the 13th rising edge of SCLK and the next falling

edge of CS. The SDATA pin will be placed back into TRI-STATE after the 16th falling edge of SCLK, or at the

rising edge of CS, whichever occurs first. After a conversion is completed, the quiet time (tQUIET) must be

satisfied before bringing CS low again to begin another conversion.

Product Folder Links: ADC081S021

000...001

000...010

011...111

111...000

000...000

111...111

111...110

ADC CODE

ANALOG INPUT

1 LSB = VA/256

1 LSB +VA-1 LSB

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

Sixteen SCLK cycles are required to read a complete sample from the ADC. The sample bits (including leading

or trailing zeroes) are clocked out on falling edges of SCLK, and are intended to be clocked in by a receiver on

subsequent rising edges of SCLK. The ADC will produce three leading zero bits on SDATA, followed by eight

data bits, most significant first. After the data bits, the ADC will clock out four trailing zeros.

If CS goes low before the rising edge of SCLK, an additional (fourth) zero bit may be captured by the next falling

edge of SCLK.

Determining Throughput

Throughput depends on the frequency of SCLK and how much time is allowed to elapse between the end of one

conversion and the start of another. At the maximum specified SCLK frequency, the maximum ensured

throughput is obtained by using a 20 SCLK frame. As shown in Figure 2, the minimum allowed time between CS

falling edges is determined by 1) 12.5 SCLKs for Hold mode, 2) the larger of two quantities: either the minimum

required time for Track mode (tACQ) or 2.5 SCLKs to finish reading the result and 3) 0, 1/2 or 1 SCLK padding to

ensure an even number of SCLK cycles so there is a falling SCLK edge when CS next falls. For example, at the

fastest rate for this family of parts, SCLK is 20MHz and 2.5 SCLKs are 125ns, so the minimum time between CS

falling edges is calculated by

12.5*50ns + 350ns + 0.5*50ns = 1000ns (1)

(12.5 SCLKs + tACQ + 1/2 SCLK) which corresponds to a maximum throughput of 1MSPS. At the slowest rate for

this family, SCLK is 1MHz. Using a 20 cycle conversion frame as shown in Figure 2 yields a 20μs time between

CS falling edges for a throughput of 50KSPS. It is possible, however, to use fewer than 20 clock cycles provided

the timing parameters are met. With a 1MHz SCLK, there are 2500ns in 2.5 SCLK cycles, which is greater than

tACQ. After the last data bit has come out, the clock will need one full cycle to return to a falling edge. Thus the

total time between falling edges of CS is 12.5*1μs +2.5*1μs +1*1μs=16μs which is a throughput of 62.5KSPS.

ADC081S021 TRANSFER FUNCTION

The output format of the ADC is straight binary. Code transitions occur midway between successive integer LSB

values. The LSB width for the ADC is VA/256. The ideal transfer characteristic is shown in Figure 20. The

transition from an output code of 0000 0000 to a code of 0000 0001 is at 1/2 LSB, or a voltage of VA/512. Other

code transitions occur at steps of one LSB.

Figure 20. Ideal Transfer Characteristic

Product Folder Links: ADC081S021

VIN

26 pF

4 pF

Conversion Phase - Switch Open

Track Phase - Switch Closed

MICROPROCESSOR

DSP

SCLK

SDATA

GND

ADC081S021

LP2950 5V

1 PF0.1 PF 0.1 PF1 PF

VIN

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

TYPICAL APPLICATION CIRCUIT

A typical application of the ADC is shown in Figure 21. Power is provided in this example by the Texas

Instruments LP2950 low-dropout voltage regulator, available in a variety of fixed and adjustable output voltages.

The power supply pin is bypassed with a capacitor network located close to the ADC. Because the reference for

the ADC is the supply voltage, any noise on the supply will degrade device noise performance. To keep noise off

the supply, use a dedicated linear regulator for this device, or provide sufficient decoupling from other circuitry to

keep noise off the ADC supply pin. Because of the ADC's low power requirements, it is also possible to use a

precision reference as a power supply to maximize performance. The three-wire interface is shown connected to

a microprocessor or DSP.

Figure 21. Typical Application Circuit

ANALOG INPUTS

An equivalent circuit for the ADC's input is shown in Figure 22. Diodes D1 and D2 provide ESD protection for the

analog inputs. At no time should the analog input go beyond (VA+ 300 mV) or (GND −300 mV), as these ESD

diodes will begin to conduct, which could result in erratic operation. For this reason, the ESD diodes should not

be used to clamp the input signal.

The capacitor C1 in Figure 22 has a typical value of 4 pF, and is mainly the package pin capacitance. Resistor

R1 is the on resistance of the track / hold switch, and is typically 500 ohms. Capacitor C2 is the ADC sampling

capacitor and is typically 26 pF. The ADC will deliver best performance when driven by a low-impedance source

to eliminate distortion caused by the charging of the sampling capacitance. This is especially important when

using the ADC to sample AC signals. Also important when sampling dynamic signals is an anti-aliasing filter.

Figure 22. Equivalent Input Circuit

DIGITAL INPUTS AND OUTPUTS

The ADC digital inputs (SCLK and CS) are not limited by the same maximum ratings as the analog inputs. The

digital input pins are instead limited to +5.25V with respect to GND, regardless of VA, the supply voltage. This

allows the ADC to be interfaced with a wide range of logic levels, independent of the supply voltage.

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

MODES OF OPERATION

The ADC has two possible modes of operation: normal mode, and shutdown mode. The ADC enters normal

mode (and a conversion process is begun) when CS is pulled low. The device will enter shutdown mode if CS is

pulled high before the tenth falling edge of SCLK after CS is pulled low, or will stay in normal mode if CS remains

low. Once in shutdown mode, the device will stay there until CS is brought low again. By varying the ratio of time

spent in the normal and shutdown modes, a system may trade-off throughput for power consumption, with a

sample rate as low as zero.

Normal Mode

The fastest possible throughput is obtained by leaving the ADC in normal mode at all times, so there are no

power-up delays. To keep the device in normal mode continuously, CS must be kept low until after the 10th

falling edge of SCLK after the start of a conversion (remember that a conversion is initiated by bringing CS low).

If CS is brought high after the 10th falling edge, but before the 16th falling edge, the device will remain in normal

mode, but the current conversion will be aborted, and SDATA will return to TRI-STATE (truncating the output

word).

Sixteen SCLK cycles are required to read all of a conversion word from the device. After sixteen SCLK cycles

have elapsed, CS may be idled either high or low until the next conversion. If CS is idled low, it must be brought

high again before the start of the next conversion, which begins when CS is again brought low.

After sixteen SCLK cycles, SDATA returns to TRI-STATE. Another conversion may be started, after tQUIET has

elapsed, by bringing CS low again.

Shutdown Mode

Shutdown mode is appropriate for applications that either do not sample continuously, or it is acceptable to trade

throughput for power consumption. When the ADC is in shutdown mode, all of the analog circuitry is turned off.

To enter shutdown mode, a conversion must be interrupted by bringing CS high anytime between the second

and tenth falling edges of SCLK, as shown in Figure 23. Once CS has been brought high in this manner, the

device will enter shutdown mode, the current conversion will be aborted and SDATA will enter TRI-STATE. If CS

is brought high before the second falling edge of SCLK, the device will not change mode; this is to avoid

accidentally changing mode as a result of noise on the CS line.

Figure 23. Entering Shutdown Mode

Figure 24. Entering Normal Mode

To exit shutdown mode, bring CS back low. Upon bringing CS low, the ADC will begin powering up (power-up

time is specified in the Timing Specifications table). This microsecond of power-up delay results in the first

conversion result being unusable. The second conversion performed after power-up, however, is valid, as shown

in Figure 24.

Product Folder Links: ADC081S021

ADC081S021

SNAS308F –APRIL 2005–REVISED JANUARY 2014

www.ti.com

If CS is brought back high before the 10th falling edge of SCLK, the device will return to shutdown mode. This is

done to avoid accidentally entering normal mode as a result of noise on the CS line. To exit shutdown mode and

remain in normal mode, CS must be kept low until after the 10th falling edge of SCLK. The ADC will be fully

powered-up after 16 SCLK cycles.

POWER MANAGEMENT

The ADC takes time to power-up, either after first applying VA, or after returning to normal mode from shutdown

mode. This corresponds to one "dummy" conversion for any SCLK frequency within the specifications in this

document. After this first dummy conversion, the ADC will perform conversions properly. Note that the tQUIET time

must still be included between the first dummy conversion and the second valid conversion.

When the VAsupply is first applied, the ADC may power up in either of the two modes: normal or shutdown. As

such, one dummy conversion should be performed after start-up, as described in the previous paragraph. The

part may then be placed into either normal mode or the shutdown mode, as described in Sections Normal Mode

and Shutdown Mode.

When the ADC is operated continuously in normal mode, the maximum ensured throughput is fSCLK / 20 at the

maximum specified fSCLK. Throughput may be traded for power consumption by running fSCLK at its maximum

specified rate and performing fewer conversions per unit time, raising the ADC CS line after the 10th and before

the 15th fall of SCLK of each conversion. A plot of typical power consumption versus throughput is shown in the

Typical Performance Curves section. To calculate the power consumption for a given throughput, multiply the

fraction of time spent in the normal mode by the normal mode power consumption and add the fraction of time

spent in shutdown mode multiplied by the shutdown mode power consumption. Note that the curve of power

consumption vs. throughput is essentially linear. This is because the power consumption in the shutdown mode

is so small that it can be ignored for all practical purposes.

POWER SUPPLY NOISE CONSIDERATIONS

The charging of any output load capacitance requires current from the power supply, VA. The current pulses

required from the supply to charge the output capacitance will cause voltage variations on the supply. If these

variations are large enough, they could degrade SNR and SINAD performance of the ADC. Furthermore,

discharging the output capacitance when the digital output goes from a logic high to a logic low will dump current

into the die substrate, which is resistive. Load discharge currents will cause "ground bounce" noise in the

substrate that will degrade noise performance if that current is large enough. The larger the output capacitance,

the more current flows through the die substrate and the greater is the noise coupled into the analog channel,

degrading noise performance.

To keep noise out of the power supply, keep the output load capacitance as small as practical. It is good practice

to use a 100 Ωseries resistor at the ADC output, located as close to the ADC output pin as practical. This will

limit the charge and discharge current of the output capacitance and maintain noise performance.

Product Folder Links: ADC081S021

ADC081S021

www.ti.com

SNAS308F –APRIL 2005–REVISED JANUARY 2014

REVISION HISTORY

Changes from Revision D (March 2013) to Revision E Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 16

Changes from Revision E (March 2013) to Revision F Page

• Changed sentence in the "Using the ADC081S021" section ............................................................................................. 12

Product Folder Links: ADC081S021

PACKAGE OPTION ADDENDUM

www.ti.com 13-Sep-2014

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

ADC081S021CIMF NRND SOT-23 DBV 6 1000 TBD Call TI Call TI -40 to 85 X09C

ADC081S021CIMF/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 X09C

ADC081S021CIMFX/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 X09C

ADC081S021CISD/NOPB ACTIVE WSON NGF 6 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 X9C

ADC081S021CISDX/NOPB ACTIVE WSON NGF 6 4500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 X9C

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

PACKAGE OPTION ADDENDUM

www.ti.com 13-Sep-2014

Addendum-Page 2

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

ADC081S021CIMF SOT-23 DBV 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081S021CIMF/NOPB SOT-23 DBV 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081S021CIMFX/NOP

BSOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081S021CISD/NOPB WSON NGF 6 1000 178.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1

ADC081S021CISDX/NOP

BWSON NGF 6 4500 330.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 31-Oct-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

ADC081S021CIMF SOT-23 DBV 6 1000 210.0 185.0 35.0

ADC081S021CIMF/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0

ADC081S021CIMFX/NOP

BSOT-23 DBV 6 3000 210.0 185.0 35.0

ADC081S021CISD/NOPB WSON NGF 6 1000 210.0 185.0 35.0

ADC081S021CISDX/NOP

BWSON NGF 6 4500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 31-Oct-2013

Pack Materials-Page 2

MECHANICAL DATA

NGF0006A

www.ti.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Digilent:

410-286P