SLP-12212610100 - Seiko Instruments USA, Inc.

DOCUMENT NUMBER NCD-64B2-02

SLP-1 Series

Single-Mode

STTM CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Seiko Instruments Inc.

Components Sales Dept.

8, Nakase 1-Chome

Mihama-ku, Chiba-shi, Chiba-ken

261 JAPA N

Telephone : 043-211-1214

-1215

Facsimile : 043-211-8035

SLP-1 Series Single-Mode STTM CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Document Number NCD-64B2-01

NCD-45B1-01 May.1994

NCD-4oB5-01 October.1994

NCD-64B2-01 April.1996

NCD-64B2-02 September.1996

The information contained herein shall not reproduced or disclosed to any third party

without the express written consent of SII.

The Specifications contained herein are subject to change without notice.

SIIis a trademark of Seiko Instruments Inc.

STis a registered tredemark of AT&T Technologies.

Kevleris a registered tredemark of E.I. du pont de Nemours & Company Inc.

Please address any questions, comments, and suggestions to:

Seiko Instruments USA Inc.

Electronics Components Division

2990 West Lomita Boulevard

Torrance, CA 90505, U.S.A.

Phone: 310-517-7780

Fax: 310-517-7792

Seiko Instruments GmbH

OFC Division

Siemensstraße 9b

D-63263 Neu-Isenburg, Germany

Phone: 06102-297-0

Fax: 06102-297-211

Seiko Instruments (H.K.) Ltd.

Sales Department

4th & 5th Floor, Wyler Center 2

200 Tai Lin Pai Road, Kwai Chung

N.T., Kowloon, Hong Kong

Phone: 852-2421-8611

Fax: 852-2480-5479

Seiko Instruments Taiwan Inc.

Sales Department

5F-1, No.99, Sec. 2, Chung Shan

Rd.

Taipei 104, Taiwan, R.O.C.

Phone: 02-563-5001, 523-5111

Fax: 02-521-9519

Seiko Instruments Singapore pte. Ltd.

2, Marsiling Lane,

Woodlands New Town,

Singapore, 2573, Singapore

Phone: 65-2691370

Fax: 65-2699729

TABLE OF CONTENTS

Section Page

1. PROVISION 1

1.1 Application Limit 1

2. PARTS NUMBER 1

3. GENERAL SPECIFICATIONS 2

3.1 Parts and Materials 2

3.2 Physical Dimensions 2

3.3 General Tolerances 2

4. PACKING 3

Table

Table 1 Parts Number 1

Table 2 Parts and Materials 2

Table 3 Parts and Materials ( Main body ) 2

Table 4 General Tolerance 2

Figure

Figure 1 SLP-1 Connector 4

Figure 2 SLP-1 Connector ( PD type ) 5

Figure 3 to 8 Part Dimensions 6

iii

1. PROVISION

1.1 Application Limit

These specifications apply to the SLP-1 Single-Mode STTM CONNECTOR PLUG

supplied by SII.

2. PARTS NUMBER

Parts Number of the Connector is Shown in Table 1.

Table 1 Parts Number

3. GENERAL SPECIFICATIONS

3.1 Parts and Materials

Parts and the materials are shown in Table 2 to 3.

Table 2 Parts and materials

No. Part Name Q'ty Material Notes

①Main body 1See Table 3 - -

➁Kevler crimping ring 1Aluminum alloy - -

③Hood ( for φ3.0mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black

➃Hood ( for φ0.9mm cord) ( 1 ) Synthetic Rubber According to Table 1, Color : Black

➄Cap 1 PVC Color : Black

Table 3 Parts and materials (Main body )

No. Part Name Q'ty Material Notes

⑥Ferrule 1Zirconia Ceramics - -

⑦Shell 1Zinc Die-cast Nickel Plating

⑧Byyonet 1Zinc Die-cast Nickel Plating

⑨Spring 1Stainless Steel - -

➉C-Ring 1Stainless Steel - -

3.2 Physical Dimensions

Figure 1 to 2 shows the assembled state of SLP-1.

Figure 3 to 8 show the part dimension.

3.3 General Tolerances

Permissible deviation in dimensions without tolerance indication is in accordance with

JIS B 0405 class m, as shown in Table 4.

Table 4 General tolerance (JIS B 0405 class m)

Basic size step (mm)

Over Under Permissible deviation (mm)

0.5 3

630

30 120

±0.1

±0.2

±0.3

4. PACKING

The product is packed to prevent damage during shippment.

note.1: This drawing does not include Caps. Unit: mm

Figure 1 SLP-1 CONNECTOR

note.1: This drawing does not include Caps. Unit: mm

Figure 2 SLP-1 CONNECTOR ( PD Type )

Unit: mm

Figure 3 ①Main body

note . End curve offset = 0.05 mm or less. ( Pre-dome )

Unit: mm

Figure 4 ①Main body ( PD Type )

Unit: mm

Figure 5 ➁Kevler crimping ring

Unit: mm

Figure 6 ③Hood

Unit: mm

Figure 7 ➃Hood

Unit: mm

Figure 8 ➄Cap