KEMET Organic Capacitor (KO-CAP) T530 High Capacitance/125C Rated Polymer Tantalum Overview The KEMET Organic Capacitor (KO-CAP) is a tantalum capacitor with a Ta anode and Ta2O5 dielectric. A conductive organic polymer replaces the traditionally used MnO2 as the cathode plate of the capacitor. This results in very low ESR and improved capacitance retention at high frequency. The KOCAP also exhibits a benign failure mode which eliminates the ignition failures that can occur in standard MnO2 tantalum types. KO-CAPs may also be operated at steady state voltages up to 90% of rated voltage for part types with rated voltages of 10 volts and up to 80% of rated voltage for part types >10 volts with equivalent or better reliability than traditional MnO2 tantalum capacitors operated at 50% of rated voltage. The T530 Series KO-CAP offers the same advantages as the T520 Series but also has the added advantages of higher capacitance, 125C performance capability, higher ripple current handling capability and a lower ESR range. Packaged as multiple anodes to reduce the depth that the signal must penetrate, this parallel arrangement reduces the ESR further still to achieve the highest capacitance and lowest ESR of any other type of surface mount capacitor with typical ESR values as low as 4 m. With reduced ESR, the enhanced capacitance retention at higher frequencies provides the lowest total capacitance and most economical solution for high power applications. Benefits Applications * * * * * * * * * * * * * * ESR: 4 m to 40 m Typical applications include high speed server, microprocessor 125C maximum operating temperature decoupling and high ripple current applications. Polymer cathode technology High frequency capacitance retention Non-ignition failure mode Capacitance: 150 F to 1,500 F 100% accelerated steady state aging 100% surge current tested Utilizes multiple tantalum anode technology Volumetric efficiency Use up to 90% of rated voltage (10% derating) for part types 10 V Use up to 80% of rated voltage (20% derating) for part types > 10 V Self-healing mechanism EIA standard case sizes Environmental Compliance RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn Solder One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 1 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum SPICE For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. Ordering Information T 530 X 337 M 010 A T E005 Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance Voltage Failure Rate/ Design Lead Material ESR Code 530 = High Capacitance 125C Rated Polymer D, X, Y First two digits represent significant figures. Third digit specifies number of zeros. M = 20% T= Tantalum 2R5 = 2.5 V 003 = 3 V 004 = 4 V 006 = 6.3 V 010 = 10 V 016 = 16 V A = N/A T = 100% Matte E = ESR Last Tin (Sn) Plated three digits specify ESR H = Tin/Lead in m (005 = (SnPb) Solder Coated (5% Pb 5 m ) minimum) G = Gold Plated Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Performance Characteristics Item Performance Characteristics Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range DF (120 Hz) ESR (100 kHz) Leakage Current -55C to 125C 150 - 1,500 F @ 120 Hz/25C M Tolerance (20%) 2.5 - 16 V 8% Refer to Part Number Electrical Specification Table 0.1 CV (A) at rated voltage after 5 minutes (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 2 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Qualification Test Condition Characteristics C/C Endurance Storage Life Humidity Temperature Stability 105C @ rated voltage, 2,000 hours 125C @ 2/3 rated voltage, 2,000 hours 125C @ 0 volts, 2,000 hours 60C, 90% RH, 1,000 hours, No Load Extreme temperature exposure at a succession of continuous steps at +25C, -55C, +25C, +85C, +105C, +25C DF initial limit DCL 2 x initial limit @ 125C ESR 2 x initial limit C/C Within -20%/+10% of initial value DF Within initial limits DCL Within 2.0 x initial limit ESR Within 2.0 x initial limit C/C Within -5%/+35% of initial value DF initial limit DCL Within 3.0 x initial limit +25C -55C +85C +125C C/C IL* 20% 20% 30% DF IL IL 1.2 x IL 1.5 x IL DCL IL n/a 10 x IL 10 x IL C/C Surge Voltage Mechanical Shock/Vibration Within -20%/+10% of initial value 105C, 1.32 x rated voltage, 33 Resistance, 1,000 cycles MIL-STD-202, Method 213, Condition I, 100 G peak MIL-STD-202, Method 204, Condition D, 10 Hz to 2,000 Hz, 20 G peak Within -20%/+10% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits C/C Within 10% of initial value DF Within initial limits DCL Within initial limits *IL = Initial limit Certification DSCC Drawing 04052 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 3 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Electrical Characteristics Capacitance vs. Frequency ESR vs. Frequency 10 1,000 T530D227M006ATE006_Imp T530X477M006ATE004_Imp 1 T530D227M006ATE006_ESR 100 T530Y337M006ATE005_ESR Capacitance (F) Impedance, ESR (Ohms) T530Y337M006ATE005_Imp T530X477M006ATE004_ESR 0.1 T530D227M006ATE006 10 T530Y337M006ATE005 T530X477M006ATE004 0.01 0.001 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 1 10,000,000 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 10,000,000 Dimensions - Millimeters (Inches) Metric will govern Termination cutout at KEMET's option, either end Case Size KEMET D X Y EIA Component L* W* H* F* 0.1 S* 0.3 B* 0.15 (.004) (.012) (Ref) .006 7.3 0.3 4.3 0.3 2.8 0.3 2.4 (.094) (0.287 0.012) (0.169 0.012) (0.110 0.012) 7.3 0.3 4.3 0.3 4.3 0.3 7343-43 2.4 (.094) (0.287 0.012) (0.169 0.012) (0.157 0.012) 7.3 0.3 4.3 0.3 7343-40 4.0 (0.157) 2.4 (.094) (0.287 0.012) (0.169 0.012) 7343-31 1.3 (.051) 0.5 (.020) 1.3 (.051) 0.5 (.020) 1.3 (.051) 0.5 (.020) X (Ref) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref) 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) Notes: (Ref) - Dimensions provided for reference only. No dimensions are provided for B, P or R because low profile cases do not have a bevel or a notch. * MIL-PRF-55365/8 specified dimensions (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 4 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Table 1 - Ratings & Part Number Reference Rated Voltage Rated Case Code/ Cap Case Size KEMET Part Number DC Leakage DF ESR % @ +20C 120 Hz Maximum 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 % @ +20C 120 Hz Maximum m @ +20C 100 kHz Maximum 5 6 10 5 5 6 7 6 10 7 6 5 6 4 5 6 5 10 10 10 8 5 6 6 10 5 6 5 4 5 6 10 6 5 6 6 10 5 6 10 5 4 5 6 10 10 18 5 6 m @ +20C 100 kHz Maximum DF ESR VDC F KEMET/EIA (See below for part options) 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 470 470 470 560 680 680 680 680 680 680 680 1000 1000 1000 1000 1000 1500 470 680 1000 1500 330 330 470 470 470 470 680 680 680 680 680 1000 220 220 330 330 330 330 330 470 470 470 470 470 680 680 150 150 D/7343-31 D/7343-31 D/7343-31 D/7343-31 Y/7343-40 Y/7343-40 Y/7343-40 D/7343-31 D/7343-31 D/7343-31 X/7343-43 Y/7343-40 Y/7343-40 X/7343-43 X/7343-43 X/7343-43 X/7343-43 D/7343-31 D/7343-31 X/7343-43 X/7343-43 D/7343-31 D/7343-31 D/7343-31 D/7343-31 Y/7343-40 Y/7343-40 Y/7343-40 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 D/7343-31 D/7343-31 D/7343-31 D/7343-31 Y/7343-40 Y/7343-40 Y/7343-40 Y/7343-40 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 D/7343-31 D/7343-31 T530D477M2R5A(1)E005 T530D477M2R5A(1)E006 T530D477M2R5A(1)E010 T530D567M2R5A(1)E005 T530Y687M2R5A(1)E005 T530Y687M2R5A(1)E006 T530Y687M2R5A(1)E007 T530D687M2R5A(1)E006 T530D687M2R5A(1)E010 T530D687M2R5A(1)E007 T530X687M2R5A(1)E006 T530Y108M2R5A(1)E005 T530Y108M2R5A(1)E006 T530X108M2R5A(1)E004 T530X108M2R5A(1)E005 T530X108M2R5A(1)E006 T530X158M2R5A(1)E005 T530D477M003A(1)E010 T530D687M003A(1)E010 T530X108M003A(1)E010 T530X158M003A(1)E008 T530D337M004A(1)E005 T530D337M004A(1)E006 T530D477M004A(1)E006 T530D477M004A(1)E010 T530Y477M004A(1)E005 T530Y477M004A(1)E006 T530Y687M004A(1)E005 T530X687M004A(1)E004 T530X687M004A(1)E005 T530X687M004A(1)E006 T530X687M004A(1)E010 T530X108M004A(1)E006 T530D227M006A(1)E005 T530D227M006A(1)E006 T530D337M006A(1)E006 T530D337M006A(1)E010 T530Y337M006A(1)E005 T530Y337M006A(1)E006 T530Y337M006A(1)E010 T530Y477M006A(1)E005 T530X477M006A(1)E004 T530X477M006A(1)E005 T530X477M006A(1)E006 T530X477M006A(1)E010 T530X687M006A(1)E010 T530X687M006A(1)E018 T530D157M010A(1)E005 T530D157M010A(1)E006 VDC F KEMET/EIA (See below for part options) A @ +20C Maximum/ 5 Minutes 118 118 118 140 170 170 170 170 170 170 170 250 250 250 250 250 375 141 204 300 450 132 132 188 188 188 188 272 272 272 272 272 400 139 139 208 208 208 208 208 296 296 296 296 296 428 428 150 150 A @ +20C Maximum/ 5 Minutes Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current Moisture Sensitivity Rated Temp (mA) +45C 100 kHz Temperature 260C (C) 7100 6500 5000 7100 7300 6600 6100 6500 5000 6000 6700 7300 6600 8200 7300 6700 7300 5000 5000 5200 5800 7100 6500 6500 5000 7300 6600 7300 8200 7300 6700 5200 6700 7100 6500 6500 5000 7300 6600 5100 7300 8200 7300 6700 5200 5200 3900 7100 6500 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 (mA) +45C 100 kHz Temperature 260C (C) Maximum Allowable Ripple Current Moisture Sensitivity Rated Temp Other part number options: (1) Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. T2019_T530 * 7/22/2013 5 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Table 1 - Ratings & Part Number Reference cont'd Rated Voltage Rated Case Code/ Cap Case Size KEMET Part Number DC Leakage DF ESR % @ +20C 120 Hz Maximum 8 8 8 8 8 8 8 8 8 8 8 % @ +20C 120 Hz Maximum m @ +20C 100 kHz Maximum 10 6 10 6 4 5 6 10 15 25 40 m @ +20C 100 kHz Maximum DF ESR VDC F KEMET/EIA (See below for part options) 10 10 10 10 10 10 10 10 16 16 16 150 220 220 220 330 330 330 330 150 150 150 D/7343-31 D/7343-31 D/7343-31 Y/7343-40 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 X/7343-43 T530D157M010A(1)E010 T530D227M010A(1)E006 T530D227M010A(1)E010 T530Y227M010A(1)E006 T530X337M010A(1)E004 T530X337M010A(1)E005 T530X337M010A(1)E006 T530X337M010A(1)E010 T530X157M016A(1)E015 T530X157M016A(1)E025 T530X157M016A(1)E040 VDC F KEMET/EIA (See below for part options) A @ +20C Maximum/ 5 Minutes 150 220 220 220 330 330 330 330 240 240 240 A @ +20C Maximum/ 5 Minutes Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current Moisture Sensitivity Rated Temp (mA) +45C 100 kHz Temperature 260C (C) 5000 6500 5000 6600 8200 7300 6700 5200 4200 3300 2600 3 3 3 3 3 3 3 3 3 3 3 125 125 125 125 125 125 125 125 125 125 125 (mA) +45C 100 kHz Temperature 260C (C) Maximum Allowable Ripple Current Moisture Sensitivity Rated Temp Other part number options: (1) Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H). Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. T2019_T530 * 7/22/2013 6 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Derating Guidelines Maximum Recommended Steady State Voltage Maximum Recommended Transient Voltage (1 ms - 1 s) -55C to 105C 2.5 V VR 10 V VR = 16V 90% of VR 80% of VR 105C to 125C 60% of VR 54% of VR 2.5 V VR 10 V VR = 16 V VR VR 100% 95% Maximum Transient Voltage 90% % Rated Voltage Voltage Rating 85% Recommended Application Voltage VR 10 V 80% 75% Recommended Application Voltage VR > 10 V 70% 67% 65% 60% 60% 55% 54% 50% 67% of VR 67% of VR -55 25 45 85 Temperature (C) 105 125 VR = Rated Voltage Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage which may be applied is limited by two criteria: 1. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. 2. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. See the Reverse Voltage section for allowable limits. The maximum power dissipation by case size can be determined using the table at right. The maximum power dissipation rating stated in the table must be reduced with increasing environmental operating temperatures. Refer to the table below for temperature compensation requirements. Case Code EIA Case Code Maximum Power Dissipation (P max) mWatts @ 45C with +30C Rise W Z D Y X 7343-15 7343-17 7343-31 7343-40 7443-43 325 325 255 263 270 The maximum power dissipation rating must be reduced with increasing environmental operating temperatures. Refer to the Temperature Compensation Multiplier table for details. Temperature Compensation Multipliers for Maximum Power Dissipation 45C 1.00 45 C < T 85C 0.70 85C < T 125C 0.25 T= Environmental Temperature Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = P max/R E(max) = Z P max/R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation (watts) R = ESR at specified frequency (ohms) Z = Impedance at specified frequency (ohms) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 7 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Reverse Voltage Polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity. These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table. Temperature Permissible Transient Reverse Voltage 25C 55C 85C 105C 125C* 15% of Rated Voltage 10% of Rated Voltage 5% of Rated Voltage 3% of Rated Voltage 1% of Rated Voltage *For series rated to 125C Table 2 - Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case A B C D L M H E1 Q R2 S2 T U V W EIA 3216-18 3528-21 6032-25 7343-31 6032-19 3528-15 7360-20 7360-38 7343-12 2012-12 3216-12 3528-12 6032-15 7343-20 7343-15 W 1.35 2.35 2.35 2.55 2.35 2.35 4.25 4.25 2.55 1.05 1.35 2.35 2.35 2.55 2.55 L 2.20 2.21 2.77 2.77 2.77 2.20 2.77 2.77 2.77 1.83 2.20 2.20 2.77 2.77 2.77 S 0.62 0.92 2.37 3.67 2.37 0.92 3.67 3.67 3.67 0.15 0.62 0.92 2.37 3.67 3.67 V1 6.02 6.32 8.92 10.22 8.92 6.32 10.22 10.22 10.22 4.82 6.02 6.32 8.92 10.22 10.22 V2 2.80 4.00 4.50 5.60 4.50 4.00 7.30 7.30 5.60 2.50 2.80 4.00 4.50 5.60 5.60 W 1.23 2.23 2.23 2.43 2.23 2.23 4.13 4.13 2.43 0.93 1.23 2.23 2.23 2.43 2.43 L 1.80 1.80 2.37 2.37 2.37 1.80 2.37 2.37 2.37 1.50 1.80 1.80 2.37 2.37 2.37 S 0.82 1.12 2.57 3.87 2.57 1.12 3.87 3.87 3.87 0.22 0.82 1.12 2.57 3.87 3.87 V1 4.92 5.22 7.82 9.12 7.82 5.22 9.12 9.12 9.12 3.72 4.92 5.22 7.82 9.12 9.12 V2 2.30 3.50 4.00 5.10 4.00 3.50 6.80 6.80 5.10 2.00 2.30 3.50 4.00 5.10 5.10 W 1.13 2.13 2.13 2.33 2.13 2.13 4.03 4.03 2.33 0.83 1.13 2.13 2.13 2.33 2.33 L 1.42 1.42 1.99 1.99 1.99 1.42 1.99 1.99 1.99 1.12 1.42 1.42 1.99 1.99 1.99 S 0.98 1.28 2.73 4.03 2.73 1.28 4.03 4.03 4.03 0.38 0.98 1.28 2.73 4.03 4.03 V1 4.06 4.36 6.96 8.26 6.96 4.36 8.26 8.26 8.26 2.86 4.06 4.36 6.96 8.26 8.26 V2 2.04 3.24 3.74 4.84 3.74 3.24 6.54 6.54 4.84 1.74 2.04 3.24 3.74 4.84 4.84 X1 Y1 7343-43 7343-40 2.55 2.55 2.77 2.77 3.67 3.67 10.22 10.22 5.60 5.60 2.43 2.43 2.37 2.37 3.87 3.87 9.12 9.12 5.10 5.10 2.33 2.33 1.99 1.99 4.03 4.03 8.26 8.26 4.84 4.84 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC-7351). Height of these chips may create problems in wave soldering. 2 Land pattern geometry is too small for silkscreen outline. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 8 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Soldering Process Please note that although the X/7343-43 case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case. The iron should be used to heat the solder pad, applying solder between the pad and the termination, until reflow occurs. Once reflow occurs, the iron should be removed immediately. "Wiping" the edges of a chip and heating the top surface is not recommended. During typical reflow operations, a slight darkening of the goldcolored epoxy may be observed. This slight darkening is normal and not harmful to the product. Marking permanency is not affected by this change. Profile Feature SnPb Assembly Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) 100C 150C Temperature Maximum (TSmax) 150C 200C Time (ts) from Tsmin to Tsmax) 60 - 120 seconds 60 - 120 seconds 3C/seconds maximum Ramp-up Rate (TL to TP) 3C/seconds maximum Liquidous Temperature (TL) 183C 217C Time Above Liquidous (tL) 60 - 150 seconds 60 - 150 seconds Peak Temperature (TP) 220C* 235C** 250C* 260C** 20 seconds maximum 30 seconds maximum 6C/seconds maximum 6C/seconds maximum 6 minutes maximum 8 minutes maximum Time within 5C of Maximum Peak Temperature (tP) Ramp-down Rate (TP to TL) Time 25C to Peak Temperature Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. *Case Size D, E, P, Y, and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z TP TL Temperature KEMET's families of surface mount capacitors are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020D standard for moisture sensitivity testing. The devices can safely withstand a maximum of three reflow passes at these conditions. tP Maximum Ramp Up Rate = 3C/seconds Maximum Ramp Down Rate = 6C/seconds tL Tsmax Tsmin 25 tS 25C to Peak Time Construction Polymer /Ta2O5/Ta Silver Adhesive Silver Paint Washer Leadframe (-Cathode) Leadframe (+Anode) Carbon Tantalum Wire Weld (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 9 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Capacitor Marking (KO) KEMET Multi Anode Polymer Rated Voltage KM Polarity Indicator (+) 158 3K 230 Picofarad Code KEMET ID Date Code* * 230 = 30th week of 2012 Date Code * 1 digit = Last number of Year 9 = 2009 0 = 2010 1 =2011 2 = 2012 3 = 2013 4 =2014 2nd and 3rd digit = Week of the Year 01 = 1st week of the Year to 52 = 52nd week of the Year st Storage All KO-Cap series are shipped in moisture barrier bags with a desiccant and moisture indicator card. These series are classified as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working environments with temperatures not to exceed 40C and humidity not in excess of 60% RH. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 10 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Tape & Reel Packaging Information KEMET's molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in accordance with EIA Standard 481-1: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape-fed automatic pick-and-place systems. 8 mm (0.315") or 12 mm (0.472") Top Tape Thickness 0.10 mm (0.004") Maximum Thickness 180 mm (7.0") or 330 mm (13.0") Table 3 - Packaging Quantity Case Code KEMET I S T M U L W Z V A B C D Y X E/T428P H EIA 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7360-38 7360-20 Tape Width (mm) 7" Reel* 13" Reel* 8 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 12 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 1,000 12,000 10,000 10,000 8,000 5,000 5,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 2,500 * No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 11 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo Po [10 pitches cumulative tolerance on tape 0.2 mm] E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity OD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 4 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) R Reference Note 2 25.0 (0.984) 30 (1.181) S1 Minimum Note 3 0.600 (0.024) T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum F P1 T2 Maximum W Maximum A0,B0 & K0 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) 3.5 0.05 (0.138 0.002) 5.5 0.05 (0.217 0.002) 5.5 0.05 (0.217 0.002) 4.0 0.10 (0.157 0.004) 8.0 0.10 (0.315 0.004) 8.0 0.10 (0.315 0.004) 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape, with or without components, shall pass around R without damage (see Figure 5). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481-D, paragraph 4.3, section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) see Addendum in EIA Standard 481-D for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 12 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 - 200 Bo Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Figure 3 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape s Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 56 10 72 - 200 5 S) Figure 4 - Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com R T2019_T530 * 7/22/2013 13 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Figure 5 - Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (O 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 5 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 14 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Figure 6 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 7 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 15 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum KEMET Corporation World Headquarters Europe Asia Southern Europe Paris, France Tel: 33-1-4646-1006 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Sasso Marconi, Italy Tel: 39-051-939111 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-460122 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Espoo, Finland Tel: 358-9-5406-5000 Northeast Wilmington, MA Tel: 978-658-1663 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Central Novi, MI Tel: 248-994-1030 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 16 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Electrolytic LifeCalculator http://www.kemet.com:8080/elc Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 17 KEMET Organic Capacitor (KO-CAP) - T530 High Capacitance/125C Rated Polymer Tantalum Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com Date: 2013.07.24 12:47:31 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2019_T530 * 7/22/2013 18