© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1
One world. One KEMET
Benets
• ESR:4mΩto40mΩ
• 125°C maximum operating temperature
• Polymer cathode technology
• High frequency capacitance retention
• Non-ignition failure mode
• Capacitance: 150 µF to 1,500 µF
• 100% accelerated steady state aging
• 100% surge current tested
• Utilizes multiple tantalum anode technology
• Volumetricefciency
• Useupto90%ofratedvoltage(10%derating)forparttypes≤10V
• Use up to 80% of rated voltage (20% derating) for part types > 10 V
• Self-healing mechanism
• EIA standard case sizes
Applications
Typical applications include high speed server, microprocessor
decoupling and high ripple current applications.
Overview
The KEMET Organic Capacitor (KO-CAP) is a tantalum
capacitor with a Ta anode and Ta2O5 dielectric. A conductive
organic polymer replaces the traditionally used MnO2 as the
cathode plate of the capacitor. This results in very low ESR and
improved capacitance retention at high frequency. The KO-
CAP also exhibits a benign failure mode which eliminates the
ignition failures that can occur in standard MnO2 tantalum types.
KO-CAPs may also be operated at steady state voltages up to
90%ofratedvoltageforparttypeswithratedvoltagesof≤10
volts and up to 80% of rated voltage for part types >10 volts with
equivalent or better reliability than traditional MnO2 tantalum
capacitors operated at 50% of rated voltage.
The T530 Series KO-CAP offers the same advantages as
the T520 Series but also has the added advantages of higher
capacitance, 125°C performance capability, higher ripple current
handling capability and a lower ESR range. Packaged as multiple
anodes to reduce the depth that the signal must penetrate, this
parallel arrangement reduces the ESR further still to achieve the
highest capacitance and lowest ESR of any other type of surface
mountcapacitorwithtypicalESRvaluesaslowas4mΩ.With
reduced ESR, the enhanced capacitance retention at higher
frequencies provides the lowest total capacitance and most
economical solution for high power applications.
KEMET Organic Capacitor (KO-CAP)
T530 High Capacitance/125°C Rated Polymer Tantalum
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn Solder
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 22
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
SPICE
Foradetailedanalysisofspecicpartnumbers,pleasevisitwww.kemet.comforafreedownloadofKEMET'sSPICEsoftware.
The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over
frequency, temperature, ripple, and DC bias conditions.
Ordering Information
T530 X337 M010 A T E005
Capacitor
Class Series Case Size Capacitance
Code (pF)
Capacitance
Tolerance Voltage Failure Rate/
Design Lead Material ESR Code Packaging
(C-Spec)
T =
Tantalum
530 = High
Capacitance
125°C Rated
Polymer
D, X, Y First two digits
representsignicant
gures.Thirddigit
speciesnumberof
zeros.
M = ±20% 2R5 = 2.5 V
003 = 3 V
004 = 4 V
006 = 6.3 V
010 = 10 V
016 = 16 V
A = N/A T = 100% Matte
Tin (Sn) Plated
H = Tin/Lead
(SnPb) Solder
Coated (5% Pb
minimum)
G = Gold Plated
E = ESR Last
three digits
specify ESR
inmΩ(005=
5mΩ)
Blank = 7"
Reel
7280 = 13"
Reel
Performance Characteristics
Item
Performance Characteristics
Operating Temperature -55°C to 125°C
Rated Capacitance Range 150 – 1,500 µF @ 120 Hz/25°C
Capacitance Tolerance M Tolerance (20%)
Rated Voltage Range 2.5 – 16 V
DF (120 Hz) 8%
ESR (100 kHz) RefertoPartNumberElectricalSpecicationTable
Leakage Current ≤0.1CV(µA)atratedvoltageafter5minutes
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 33
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Qualication
Test Condition Characteristics
Endurance 105°C @ rated voltage, 2,000 hours
125°C @ 2/3 rated voltage, 2,000 hours
ΔC/C Within-20%/+10%ofinitialvalue
DF ≤initiallimit
DCL 2 x initial limit @ 125ºC
ESR 2 x initial limit
Storage Life 125°C @ 0 volts, 2,000 hours
ΔC/C
Within-20%/+10%ofinitialvalue
DF Withininitiallimits
DCL Within2.0xinitiallimit
ESR Within2.0xinitiallimit
Humidity 60°C, 90% RH, 1,000 hours, No Load
ΔC/C Within-5%/+35%ofinitialvalue
DF ≤initiallimit
DCL Within3.0xinitiallimit
Temperature Stability
Extreme temperature exposure at a
successionofcontinuousstepsat+25ºC,
-55ºC,+25ºC,+85ºC,+105ºC,+25ºC
+25°C
-55°C
+85°C
+125°C
ΔC/C I L* ±20% ±20% ±30%
DF IL IL 1.2 x IL 1.5 x IL
DCL IL n/a 10 x IL 10 x IL
Surge Voltage 105°C,1.32xratedvoltage,33ΩResistance,1,000cycles
ΔC/C Within-20%/+10%ofinitialvalue
DF Withininitiallimits
DCL Withininitiallimits
ESR Withininitiallimits
Mechanical Shock/Vibration
MIL–STD–202, Method 213, Condition I, 100 G peak
MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,
20 G peak
ΔC/C Within±10%ofinitialvalue
DF Withininitiallimits
DCL Withininitiallimits
*IL = Initial limit
Certication
DSCC Drawing 04052
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 44
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Electrical Characteristics
1
10
100
1,000
100 1,000 10,000 100,000 1,000,000 10,000,000
Capacitance (μF)
Frequency (Hz)
T530D227M006ATE006
T530Y337M006ATE005
T530X477M006ATE004
Capacitance vs. Frequency
ESR vs. Frequency
0.001
0.01
0.1
1
100 1,000 10,000 100,000 1,000,000 10,000,000
Frequency (Hz)
T530D227M006ATE006_Imp
T530Y337M006ATE005_Imp
T530X477M006ATE004_Imp
T530D227M006ATE006_ESR
T530Y337M006ATE005_ESR
T530X477M006ATE004_ESR
Dimensions – Millimeters (Inches)
Metric will govern
15
Termination
cutout at
KEMET’s
option,
either end
Case Size
Component
KEMET EIA L* W* H* F* ±0.1
±(.004)
S* ±0.3
±(.012)
B* ±0.15
(Ref) ±.006 X (Ref) P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref)
D7343–31
7.3 ±0.3
(0.287 ±0.012)
4.3 ±0.3
(0.169 ±0.012)
2.8 ±0.3
(0.110 ±0.012)
2.4 (.094) 1.3 (.051) 0.5 (.020)
0.10 ± 0.10
(.004 ± .004)
0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138)
X7343–43
7.3 ±0.3
(0.287 ±0.012)
4.3 ±0.3
(0.169 ±0.012)
4.3 ±0.3
(0.157 ±0.012)
2.4 (.094) 1.3 (.051) 0.5 (.020)
0.10 ± 0.10
(.004 ± .004)
1.7 (.067) 1.0 (.039) 0.13 (.0 05) 3.8 (.150) 3.5 (.138) 3.5 (.138)
Y7343–40
7.3 ±0.3
(0.287 ±0.012)
4.3 ±0.3
(0.169 ±0.012)
4.0 (0.157) 2.4 (.094) 1.3 (.051) 0.5 (.020)
0.10 ± 0.10
(.004 ± .004)
1.7 (.067) 1.0 (.039) 0.13 (.0 05) 3.8 (.150) 3.5 (.138) 3.5 (.138)
Notes: (Ref) – Dimensions provided for reference only. No dimensions are provided for B, P or R because low prole cases do not have a bevel or a notch.
* MIL–PRF–55365/8 specied dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 55
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage DF ESR
Maximum
Allowable
Ripple Current
Moisture
Sensitivity
Rated
Temp
VDC µF KEMET/EIA (See below for
part options)
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C
120 Hz
Maximum
mΩ @ +20°C
100 kHz
Maximum
(mA) +45°C 100 kHz Temperature
≤ 260ºC(ºC)
2.5 470 D/7343-31 T530D477M2R5A(1)E005 118 8 5 7100 3125
2.5 470 D/7343-31 T530D477M2R5A(1)E006 118 8 6 6500 3125
2.5 470 D/7343-31 T530D477M2R5A(1)E010 118 810 5000 3125
2.5 560 D/7343-31 T530D567M2R5A(1)E005 140 8 5 7100 3125
2.5 680 Y/7343-40 T530Y687M2R5A(1)E005 170 8 5 7300 3125
2.5 680 Y/7343-40 T530Y687M2R5A(1)E006 170 8 6 6600 3125
2.5 680 Y/7343-40 T530Y687M2R5A(1)E007 170 8 7 6100 3125
2.5 680 D/7343-31 T530D687M2R5A(1)E006 170 8 6 6500 3125
2.5 680 D/7343-31 T530D687M2R5A(1)E010 170 810 5000 3125
2.5 680 D/7343-31 T530D687M2R5A(1)E007 170 8 7 6000 3125
2.5 680 X/7343-43 T530X687M2R5A(1)E006 170 8 6 6700 3125
2.5 1000 Y/7343-40 T530Y108M2R5A(1)E005 250 8 5 7300 3125
2.5 1000 Y/7343-40 T530Y108M2R5A(1)E006 250 8 6 6600 3125
2.5 1000 X/7343-43 T530X108M2R5A(1)E004 250 8 4 8200 3125
2.5 1000 X/7343-43 T530X108M2R5A(1)E005 250 8 5 7300 3125
2.5 1000 X/7343-43 T530X108M2R5A(1)E006 250 8 6 6700 3125
2.5 1500 X/7343-43 T530X158M2R5A(1)E005 375 8 5 7300 3125
3470 D/7343-31 T530D477M003A(1)E010 141 810 5000 3125
3680 D/7343-31 T530D687M003A(1)E010 204 810 5000 3125
31000 X/7343-43 T530X108M003A(1)E010 300 810 5200 3125
31500 X/7343-43 T530X158M003A(1)E008 450 8 8 5800 3125
4330 D/7343-31 T530D337M004A(1)E005 132 8 5 7100 3125
4330 D/7343-31 T530D337M004A(1)E006 132 8 6 6500 3125
4470 D/7343-31 T530D477M004A(1)E006 188 8 6 6500 3125
4470 D/7343-31 T530D477M004A(1)E010 188 810 5000 3125
4470 Y/7343-40 T530Y477M004A(1)E005 188 8 5 7300 3125
4470 Y/7343-40 T530Y477M004A(1)E006 188 8 6 6600 3125
4680 Y/7343-40 T530Y687M004A(1)E005 272 8 5 7300 3125
4680 X/7343-43 T530X687M004A(1)E004 272 8 4 8200 3125
4680 X/7343-43 T530X687M004A(1)E005 272 8 5 7300 3125
4680 X/7343-43 T530X687M004A(1)E006 272 8 6 6700 3125
4680 X/7343-43 T530X687M004A(1)E010 272 810 5200 3125
41000 X/7343-43 T530X108M004A(1)E006 400 8 6 6700 3125
6.3 220 D/7343-31 T530D227M006A(1)E005 139 8 5 7100 3125
6.3 220 D/7343-31 T530D227M006A(1)E006 139 8 6 6500 3125
6.3 330 D/7343-31 T530D337M006A(1)E006 208 8 6 6500 3125
6.3 330 D/7343-31 T530D337M006A(1)E010 208 810 5000 3125
6.3 330 Y/7343-40 T530Y337M006A(1)E005 208 8 5 7300 3125
6.3 330 Y/7343-40 T530Y337M006A(1)E006 208 8 6 6600 3125
6.3 330 Y/7343-40 T530Y337M006A(1)E010 208 810 5100 3125
6.3 470 Y/7343-40 T530Y477M006A(1)E005 296 8 5 7300 3125
6.3 470 X/7343-43 T530X477M006A(1)E004 296 8 4 8200 3125
6.3 470 X/7343-43 T530X477M006A(1)E005 296 8 5 7300 3125
6.3 470 X/7343-43 T530X477M006A(1)E006 296 8 6 6700 3125
6.3 470 X/7343-43 T530X477M006A(1)E010 296 810 5200 3125
6.3 680 X/7343-43 T530X687M006A(1)E010 428 8 10 5200 3125
6.3 680 X/7343-43 T530X687M006A(1)E018 428 8 18 3900 3125
10 150 D/7343-31 T530D157M010A(1)E005 150 8 5 7100 3125
10 150 D/7343-31 T530D157M010A(1)E006 150 8 6 6500 3125
VDC µF KEMET/EIA (See below for
part options)
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C
120 Hz
Maximum
mΩ @ +20°C
100 kHz
Maximum
(mA) +45°C 100 kHz Temperature
≤ 260ºC(ºC)
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage DF ESR
Maximum
Allowable
Ripple Current
Moisture
Sensitivity
Rated
Temp
Table 1 – Ratings & Part Number Reference
Other part number options:
(1) Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H).
Also available on large (13 inch) reels. Add 7280 to the end of the part number.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked
with the higher voltage rating. Substitutions can include better than series.
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 66
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage DF ESR
Maximum
Allowable
Ripple Current
Moisture
Sensitivity
Rated
Temp
VDC µF KEMET/EIA (See below for
part options)
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C
120 Hz
Maximum
mΩ @ +20°C
100 kHz
Maximum
(mA) +45°C 100 kHz Temperature
≤ 260ºC(ºC)
10 150 D/7343-31 T530D157M010A(1)E010 150 810 5000 3125
10 220 D/7343-31 T530D227M010A(1)E006 220 8 6 6500 3125
10 220 D/7343-31 T530D227M010A(1)E010 220 810 5000 3125
10 220 Y/7343-40 T530Y227M010A(1)E006 220 8 6 6600 3125
10 330 X/7343-43 T530X337M010A(1)E004 330 8 4 8200 3125
10 330 X/7343-43 T530X337M010A(1)E005 330 8 5 7300 3125
10 330 X/7343-43 T530X337M010A(1)E006 330 8 6 6700 3125
10 330 X/7343-43 T530X337M010A(1)E010 330 810 5200 3125
16 150 X/7343-43 T530X157M016A(1)E015 240 815 4200 3 125
16 150 X/7343-43 T530X157M016A(1)E025 240 825 3300 3125
16 150 X/7343-43 T530X157M016A(1)E040 240 840 2600 3125
VDC µF KEMET/EIA (See below for
part options)
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C
120 Hz
Maximum
mΩ @ +20°C
100 kHz
Maximum
(mA) +45°C 100 kHz Temperature
≤ 260ºC(ºC)
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage DF ESR
Maximum
Allowable
Ripple Current
Moisture
Sensitivity
Rated
Temp
Table 1 – Ratings & Part Number Reference cont'd
Other part number options:
(1) Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H).
Also available on large (13 inch) reels. Add 7280 to the end of the part number.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked
with the higher voltage rating. Substitutions can include better than series.
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 77
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
50%
55%
60%
65%
70%
75%
80%
85%
90%
95%
100%
-55 25 45 85 105 125
% Rated Voltage
Temperature (ºC)
Maximum Transient Voltage
Recommended Application Voltage V
R
≤ 10 V
Recommended Application Voltage V
R
> 10 V
67%
60%
54%
Derating Guidelines
Voltage
Rating
Maximum
Recommended Steady
State Voltage
Maximum Recommended
Transient Voltage (1 ms – 1 µs)
-55°C to 105°C
2.5V≤VR≤10V
90% of VR
VR
VR = 16V
80% of VR
VR
105°C to 125°C
2.5V≤VR≤10V
60% of VR
67% of VR
VR = 16 V
54% of VR
67% of VR
VR = Rated Voltage
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent
series resistance (ESR) and the power dissipation capabilities of
the device. Permissible AC ripple voltage which may be applied is
limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any,
must not exceed the DC voltage rating of the capacitor.
2. The negative peak AC voltage in combination with bias
voltage,ifany,mustnotexceedtheallowablelimitsspeciedfor
reverse voltage. See the Reverse Voltage section for allowable
limits.
The maximum power dissipation by case size can be determined
using the table at right. The maximum power dissipation rating
stated in the table must be reduced with increasing environmental
operating temperatures. Refer to the table below for temperature
compensation requirements.
Temperature Compensation Multipliers
for Maximum Power Dissipation
≤45°C
45°C<T≤85°C
85°C<T≤125°C
1.00
0.70
0.25
T= Environmental Temperature
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
I(max) = √P max/R
E(max) = Z √P max/R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation (watts)
R = ESR at specied frequency (ohms)
Z = Impedance at specied frequency (ohms)
Case Code EIA
Case Code
Maximum Power
Dissipation (P max)
mWatts @ 45°C with
+30°C Rise
W
7343-15
325
Z
7343-17
325
D
7343-31
255
Y
7343-40
263
X
7443-43
270
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature
Compensation Multiplier table for details.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 88
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Reverse Voltage
Polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity.
These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table.
Temperature Permissible Transient Reverse Voltage
25°C
15% of Rated Voltage
55°C
10% of Rated Voltage
85°C
5% of Rated Voltage
105°C
3% of Rated Voltage
125°C*
1% of Rated Voltage
*For series rated to 125°C
Table 2 – Land Dimensions/Courtyard
KEMET
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
Case
EIA
W
L
S
V1
V2
W
L
S
V1
V2
W
L
S
V1
V2
A
3216–18
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
B
3528–21
2.35
2.21
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
C
6032–25
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
D
7343–31
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
L
6032-19
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
M
3528-15
2.35
2.20
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
H
7360-20
4.25
2.77
3.67
10.22
7.3 0
4.13
2.37
3.87
9.12
6.80
4.03
1.99
4.03
8.26
6.54
E
1
7360–38
4.25
2.77
3.67
10.22
7.3 0
4.13
2.37
3.87
9.12
6.80
4.03
1.99
4.03
8.26
6.54
Q
7343-12
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
R
2
2012-12
1.05
1.83
0.15
4.82
2.50
0.93
1.50
0.22
3.72
2.00
0.83
1.12
0.38
2.86
1.74
S2
3216–12
1.35
2.20
0.62
6.02
2.80
1.23
1.80
0.82
4.92
2.30
1.13
1.42
0.98
4.06
2.04
T
3528–12
2.35
2.20
0.92
6.32
4.00
2.23
1.80
1.12
5.22
3.50
2.13
1.42
1.28
4.36
3.24
U
6032–15
2.35
2.77
2.37
8.92
4.50
2.23
2.37
2.57
7.82
4.00
2.13
1.99
2.73
6.96
3.74
V
7343–20
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
W
7343–15
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
X
1
7343–43
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
Y
1
7343–40
2.55
2.77
3.67
10.22
5.60
2.43
2.37
3.87
9.12
5.10
2.33
1.99
4.03
8.26
4.84
Density Level A: For low-density product applications. Recommended for wave solder applications and
provides a wider process window for reow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder
attachment condition for reow solder processes.
Density Level C: For high component desity product applications. Before adapting the minimum land
pattern variations the user should perform qualication testing based on the conditions outlined in IPC
standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
2 Land pattern geometry is too small for silkscreen outline.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 99
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Time
Temperature
T
smin
25ºC to Peak
tL
tS
25
tP
T
smax
TL
TP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
Soldering Process
KEMET’s families of surface mount capacitors are compatible
withwave(singleordual),convection,IR,orvaporphasereow
techniques. Preheating of these components is recommended
toavoidextremethermalstress.KEMET'srecommended
proleconditionsforconvectionandIRreowreecttheprole
conditions of the IPC/J–STD–020D standard for moisture
sensitivity testing. The devices can safely withstand a maximum
ofthreereowpassesattheseconditions.
Please note that although the X/7343–43 case size can withstand
wavesoldering,thetallprole(4.3mmmaximum)dictatescarein
wave process development.
Handsolderingshouldbeperformedwithcareduetothedifculty
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
andthetermination,untilreowoccurs.Oncereowoccurs,the
ironshouldberemovedimmediately.“Wiping”theedgesofachip
and heating the top surface is not recommended.
Duringtypicalreowoperations,aslightdarkeningofthegold-
colored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
Prole Feature SnPb Assembly Pb-Free Assembly
Preheat/Soak
Temperature Minimum (T
Smin
)100°C 150°C
Temperature Maximum (TSmax
)150°C 200°C
Time (t
s
) from T
smin
to T
smax
) 60 – 120 seconds 60 – 120 seconds
Ramp-up Rate (T
L
to T
P
)3°C/seconds maximum 3°C/seconds maximum
Liquidous Temperature (TL)
183°C
217°C
Time Above Liquidous (t
L
) 60 – 150 seconds 60 – 150 seconds
Peak Temperature (TP)
220°C*
235°C**
250°C*
260°C**
Time within 5°C of Maximum
Peak Temperature (tP)
20 seconds maximum 30 seconds maximum
Ramp-down Rate (T
P
to T
L
)6°C/seconds maximum 6°C/seconds maximum
Time 25°C to Peak
Temperature
6 minutes maximum 8 minutes maximum
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
Construction
Polymer /Ta
2
O
5
/Ta Silver Adhesive
Carbon
Silver Paint
Washer
Tantalum Wire
Weld
Leadframe
(-Cathode)
Leadframe
(+Anode)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1010
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Capacitor Marking
(KO)
KEMET
Multi -
Anode
Polymer
Rated
Voltage
158
3 K
230
KM Polarity
Indicator (+)
Picofarad Code
KEMET ID
Date
Code*
* 230 = 30th week of 2012
Date Code *
1st digit = Last number of Year 9 = 2009
0 = 2010
1 =2011
2 = 2012
3 = 2013
4 =2014
2nd and 3rddigit=WeekoftheYear 01 = 1st week of the Year to
52 = 52nd week of the Year
Storage
All KO-CAPseriesareshippedinmoisturebarrierbagswithadesiccantandmoistureindicatorcard.Theseseriesareclassied
as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working
environments with temperatures not to exceed 40°C and humidity not in excess of 60% RH.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1111
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Tape & Reel Packaging Information
KEMET’s molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in
accordance with EIA Standard 481–1: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging
system is compatible with all tape-fed automatic pick-and-place systems.
Table 3 – Packaging Quantity
Case Code
Tape Width
(mm) 7" Reel* 13" Reel*
KEMET
EIA
I
3216-10
8
3,000
12,000
S
3216-12
8
2,500
10,000
T
3528-12
8
2,500
10,000
M
3528-15
8
2,000
8,000
U
6032-15
12
1,000
5,000
L
6032-19
12
1,000
5,000
W
7343-15
12
1,000
3,000
Z
7343-17
12
1,000
3,000
V
7343-20
12
1,000
3,000
A
3216-18
8
2,000
9,000
B
3528-21
8
2,000
8,000
C
6032-28
12
500
3,000
D
7343-31
12
500
2,500
Y
7343-40
12
500
2,000
X
7343-43
12
500
2,000
E/T428P
7360-38
12
500
2,000
H
7360-20
12
1,000
2,500
* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.
Top Tape Thickness
0.10 mm (0.004")
Maximum Thickness
8 mm (0.315")
or
12 mm (0.472") 180 mm (7.0")
or
330 mm (13.0")
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1212
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Po
T
F
W
Center Lines of Cavity
Ao
Bo
User Direction of Unreeling
Cover Tape
Ko
B
1
is for tape feeder reference only,
including draft concentric about B
o.
T
2
ØD
1
ØDo
B
1
S
1
T
1
E
1
E
2
P
1
P
2
Embossment
For cavity size,
see Note 1 Table 4
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size D0
D
1
Minimum
Note 1
E1P0 P2
R Reference
Note 2
S
1
Minimum
Note 3
T Maximum T1 Maximum
8 mm
1.5+0.10/-0.0
(0.059+0.004/-0.0)
1.0
(0.039)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
25.0
(0.984)
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm 1.5
(0.059)
30
(1.181)
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch
B
1
Maximum
Note 4
E2 Minimum F P1 T2 Maximum WMaximum A0,B0 & K0
8 mm Single (4 mm)
4.35
(0.171)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
4.0 ±0.10
(0.157 ±0.004)
2.5
(0.098)
8.3
(0.327)
Note 512 mm
Single (4 mm) &
Double (8 mm)
8.2
(0.323)
10.25
(0.404)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10
(0.315 ±0.004)
4.6
(0.181)
12.3
(0.484)
16 mm Triple (12 mm)
12.1
(0.476)
14.25
(0.561)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10
(0.315 ±0.004)
4.6
(0.181)
16.3
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 5).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity de ned by A0, B0 and K0 shall surround the component with suf cient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1313
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width Peel Strength
8 mm 0.1 to 1.0 Newton (10 to 100 gf)
12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
Ao
Bo
°
T
°
s
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Tape Maximum
Width (mm) Rotation (°
T)
8,12 20
16 – 200 10 Tape Maximum
Width (mm) Rotation ( °
S)
8,12 20
16 – 56 10
72 – 200 5
Typical Pocket Centerline
Typical Component Centerline
Figure 3 – Maximum Lateral Movement
0.5 mm maximum
0.5 mm maximum
8 mm & 12 mm Tape
1.0 mm maximum
1.0 mm maximum
16 mm Tape
Figure 4 – Bending Radius
RR
Bending
Radius
Embossed
Carrier
Punched
Carrier
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1414
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 5 – Reel Dimensions
AD(See Note)
Full Radius,
See Note
B(see Note)
Access Hole at
Slot Location
(Ø 40 mm minimum)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
W3(Includes
flange distortion
at outer edge)
W2(Measured at hub)
W1(Measured at hub)
C
(Arbor hole
diameter)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
N
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size A B Minimum C D Minimum
8 mm
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0+0.5/-0.2
(0.521+0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size N Minimum W
1
W
2
Maximum W
3
8 mm
50
(1.969)
8.4+1.5/-0.0
(0.331+0.059/-0.0)
14.4
(0.567)
Shall accommodate tape width
without interference
12 mm
12.4+2.0/-0.0
(0.488+0.078/-0.0)
18.4
(0.724)
16 mm
16.4+2.0/-0.0
(0.646+0.078/-0.0)
22.4
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1515
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 6 – Tape Leader & Trailer Dimensions
Trailer
160 mm Minimum
Carrier Tape
END START
Round Sprocket Holes
Elongated Sprocket Holes
(32 mm tape and wider)
Top Cover Tape
Top Cover Tape
Punched Carrier
8 mm & 12 mm only
Embossed Carrier
Components
100 mm
Minimum Leader
400 mm Minimum
Figure 7 – Maximum Camber
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
Elongated sprocket holes
(32 mm & wider tapes)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1616
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
KEMET Corporation
World Headquarters
2835KEMETWay
Simpsonville, SC 29681
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Corporate Of ces
Fort Lauderdale, FL
Tel: 954-766-2800
North America
Southeast
Lake Mary, FL
Tel: 407-855-8886
Northeast
Wilmington,MA
Tel: 978-658-1663
Central
Novi, MI
Tel: 248-994-1030
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Europe
Southern Europe
Paris, France
Tel: 33-1-4646-1006
Sasso Marconi, Italy
Tel: 39-051-939111
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Kamen, Germany
Tel: 49-2307-438110
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-460122
Espoo, Finland
Tel: 358-9-5406-5000
Asia
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Shenzhen, China
Tel: 86-755-2518-1306
Beijing, China
Tel: 86-10-5829-1711
Shanghai, China
Tel: 86-21-6447-0707
Taipei, Taiwan
Tel: 886-2-27528585
Southeast Asia
Singapore
Tel: 65-6586-1900
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1717
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Other KEMET Resources
Tools
Resource Location
CongureAPart:CapEdge http://capacitoredge.kemet.com
SPICE & FIT Software http://www.kemet.com/spice
Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask
Electrolytic LifeCalculator http://www.kemet.com:8080/elc
Product Information
Resource Location
Products http://www.kemet.com/products
Technical Resources (Including Soldering Techniques) http://www.kemet.com/technicalpapers
RoHS Statement http://www.kemet.com/rohs
Quality Documents http://www.kemet.com/qualitydocuments
Product Request
Resource Location
Sample Request http://www.kemet.com/sample
Engineering Kit Request http://www.kemet.com/kits
Contact
Resource Location
Website www.kemet.com
Contact Us http://www.kemet.com/contact
Investor Relations http://www.kemet.com/ir
Call Us 1-877-MyKEMET
Twitter http://twitter.com/kemetcapacitors
Disclaimer
Allproductspecications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare
notintendedtoconstitute–andKEMETspecicallydisclaims–anywarrantyconcerningsuitabilityforaspeciccustomerapplicationoruse.TheInformationisintendedforuseonly
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com T2019_T530 • 7/22/2013 1818
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Digitally signed by Jeannette Calvo
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications,
cn=Jeannette Calvo, email=jeannettecalvo@kemet.com
Date: 2013.07.24 12:47:31 -04'00'