M24308/2-13Z - ITT CANNON - Datasheet.Directory

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 1

D Sub

C-40 www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

Environmental D

D*D

The Cannon D*D Environmental Series is designed

to meet the demand for subminiature rectangular

plugs with superior vibration and moisture resist-

ance characteristics for aircraft, missile, and ground

support equipment applications.

Featuring a rugged aluminum shell and peripheral

seal, the D*D connector meets all applicable re-

quirements of MIL-C-24308. Available in both sol-

der and crimp versions, all assemblies are provided

with nylon potting cups and dust caps.

Solder type contacts are non-removable and are

factory-installed. Crimp type connectors utilize the

field-proven LITTLE CAESAR®rear insertion, rear-re-

lease retention system.

PLEASE NOTE: The D*D Series is not intermate-

able with other D Subminiature connectors.

Performance and Material Specifications

Shell Aluminum, cadmium plated with yellow chromate supplementary coating.

Contacts Solder pot: Copper alloy, gold plated .00002 (.0005) over nickel .00004 (.0010)

Crimp type: Copper alloy, gold plated .00002 (.0005) over nickel .00004 (.0010)

Contact Termination Solder pot accommodating up to #20 AWG stranded wire. Crimp type accommodat-

ing #20, #22, and #24 AWG stranded wire.

Socket Type Closed entry

Float Mounting Rivets & Washers Stainless Steel. Passivated per DQ-P-35

Test Data

Specifications

Voltage Rating All voltage figures are AC (rms), 60 Hz measured at approximately 25.0°C 50% RH.

Insulation Resistance Greater than 5,000 megohms, determined in accordance with MIL-STD-202A, Method 302

(per MIL-C-24308)

Contact Voltage Drop 2.67 millivolts, maximum, per amp

Contact Separation Force 1 to 8 ounces when tested in accordance with MIL-C-24308

Air Leakage When properly wired and potted, 1 cubic inch of air per hour max. when subjected to 30 PSI

pressure differential in accordance with MIL-C-50150, Paragraph 4.5.3.1

Vibration Exceeds test requirements of MIL-STD-202A, Method 204, Condition D

(per MIL-C-24308)

Corrosion Resistance Exceeds requirements of 50 hour exposure to salt spray in accordance with MIL-STD-202A,

(per MIL-C-24308) Method 101A, Condition B

Moisture Resistance Exceeds requirements of MIL-STD-202A, Method 106

(per MIL-C-24308)

Shock Exceeds requirements of MIL-STD-202A, Method 213, Condition G

Environmental Seal Effective from full engagement to 1/16 short of full engagement

Contact Retention Force (Crimp type) 8 pounds (35.6 newtons) minimum for first cycle; 5 pounds (22.2 newtons)

minimum after tenth cycle

Standard Layout Plugs Measured from contact-to-contact, and contact-to-shell in unmated condition

ALTITUDE (FEET)

Sea

Level 20,000 50,000 70,000

Average

Flashover 1700 1000 650 500

Test 1250 750 475 375

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 40

D Sub

www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

C-41

Environmental D

D*D

How to Order

D A D - 15 S A -

SERIES PREFIX

SHELL SIZE

CLASS

CONTACT ARRANGEMENT

CONTACT TYPE

MOUNTING STYLE

MODIFICATION

SHELL SIZE CONTACT TYPE

A, B, C, D, E P – Pin

S – Socket

CLASS

D – Environmental MOUNTING STYLE

A – Standard Mounting Holes

CONTACT ARRANGEMENT B – Float Mounts supplied

9, 15, 25, 37, 50 Std Density

Combo-D Layouts also available MODIFICATION

Contact factory

Solder Cup Terminals

SERIES PREFIX

ITT Cannon Designation

Snap-In Crimp Terminals

SERIES PREFIX

ITT Cannon Designation

D A DA F- 15 P- FO

SERIES PREFIX

SHELL SIZE

CLASS

MOUNTING STYLE

CONTACT ARRANGEMENTS

CONTACT TYPE

MODIFICATION

SHELL SIZE CONTACT ARRANGEMENTS

A, B, C, D, E 9, 15, 25, 37, 50 Std Density

15, 26, 44, 62, 88 Hi Density

Combo-D Layouts also available

CLASS CONTACT TYPE

DA – Environmental, crimp type P – Pin

S – Socket

MOUNTING STYLE

No Designator – Standard mounting MODIFICATION

F – Float mounts supplied FO – Connector supplied less contacts, for

other modifications consult factory

Add .032 (0.81) to dimensions C and E for float mounting.

Note: Panel cutout does not allow for potting cup clearance.

Panel Cutouts

USE .120(3.05) DIA. HOLE OR 4-40 TAP (CUSTOMER PREFERENCE) FOR FRONT MOUNTING.

FOR REAR MOUNTING USE .120(3.05) DIA. HOLE COUNTERSUNK FOR FLATHEAD SCREW.

.083(2.11) R. MAX.

TYPICAL

Shell Size

DED-15

DAD-26

DBD-44

DCD-62

DDD-78

±.010 (0.25)

1.442 (36.63)

1.755 (44.58)

2.295 (58.29)

2.937 (74.60)

2.859 (72.62)

Min.

1.839 (21.31)

1.157 (29.39)

1.697 (43.10)

2.357 (59.87)

2.265 (57.53)

±.010 (0.25)

.614 (15.60)

.614 (15.60))

.735 (18.67)

±.010 (0.25)

.497 (12.62)

.610 (15.49)

±.010 (0.25)

1.125 (28.58)

1.437 (36.50)

1.993 (50.62)

2.625 (66.68)

2.531 (64.29)

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 41

D Sub

C-42 www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

Environmental D

D*D

Shell Dimensions, Standard Mount

.061 +_ .005

(1.55 +_ 0.13)

.061 +_ .005

(1.55 +_ 0.13)

MAX.

.874

(22.20)

MAX.

.058 +_ .005

(1.47 +_ .013)

.677 (17.20) MAX.

CONTACT EXTENSION

.299 (7.59)

MAX.

CONACT

EXTENSION

.677

(17.20)

.089 +_ .005

(2.26 +_ 0.13)

.904

(22.96)

MAX.

.425 +_ .005

(10.80 +_ 0.13)

A MAX.

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

K +_ .005

( +_ .013)

K +_ .005

( +_ .013)

.109 (2.77) FL. TYP.

.109 (2.77)

R. TYP

10˚ TYP.

A MAX.

Float Mount Dimensions

Receptacle

.061 +_ .005

(1.55 +_ 0.13)

.061 +_ .005

(1.55 +_ 0.13)

.032 (0.81)

TOTAL

DIA. FLOAT

.032 (0.81)

TOTAL

DIA. FLOAT

.031 +_ .005

(0.79 +_ 0.13)

.031 +_ .005

(0.79 +_ 0.13)

MAX.

.874

(22.20)

MAX.

.058 +_ .005

(1.47 +_ .013)

.677 (17.20) MAX.

CONTACT

EXTENSION

MAX.

.299 (7.59) MAX.

CONACT

EXTENSION

.677

(17.20)

.089 +_ .005

(2.26 +_ 0.13)

.904

(22.96)

MAX.

.425 +_ .005

(10.80 +_ 0.13)

A MAX.

MAX.

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

K +_ .005

( +_ .013)

.109 (2.77) R. TYP.

K +_ .005

( +_ .013) .109 (2.77)

R. TYP

10˚ TYP.

Plug

NOTE: All D*D Environmental plugs and receptacles are provided with dust caps and removable potting caps.

Shell Size

DED-9P, 15P

DED-9S, 15S

DAD-15P, 26P

DAD-15S, 26S

DBD-25P, 44P

DBD-25S, 44S

DCD-37P, 62P

DCD-37S, 62S

DDD-50P, 78P

DDD-50S, 78S

Max.

1.915 (23.24)

1.233 (31.32)

1.786 (45.36)

2.458 (62.43)

2.390 (60.71)

Max.

.596 (15.14)

.567 (14.40)

.680 (17.12)

±.005 (0.13)

1.125 (28.58)

1.437 (36.50)

1.993 (50.62)

2.625 (66.68)

2.531 (64.29)

±.010 (0.25)

1.442 (36.63)

1.755 (44.58)

2.295 (58.29)

2.937 (74.60)

2.859 (72.62)

±.010 (0.25)

.614 (15.60)

.735 (18.67)

±.010 (0.25)

1.825 (20.86)

1.143 (29.03)

1.683 (42.75)

2.343 (59.51)

2.251 (57.18)

±.010 (0.25)

.483 (12.27)

.596 (15.14)

All tolerances are ±.010 (0.25) unless noted otherwise.

Plug

Receptacle

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 42

D Sub

C-43

www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

Combo D

Contact Cavity Arrangments

Contact Cavity Arrangements

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

5W1

4#20

1#8

3W3

0#20

3#8

7W2

5#20

2#8

3WK3

0#20

3#8

2WK2

0#20

2#8

11W1

10#20

1#8

9W4

5#20

4#8

5W54

0#20

5#8

13W3

10#20

3#8

21W1

20#20

1#8

8W8

0#20

8#8

17W2

15#20

2#8

17W5

12#20

5#8

13W6

7#20

6#8

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

Shell Size

Contact Arrangement

No. of Size 20 Cavities

No. of Size 8 Cavities

27W2

25#20

2#8

25W3

22#20

3#8

21WA4

17#20

4#8

36W4

32#20

4#8

24W7

17#20

7#8

47W1

46#20

1#8

43W2

41#20

2#8

2W2

0#20

2#8

A2A1 A3

A1 2

Plug

Face View Pin Insert

(Use a mirror image for

receptacle).

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 43

D Sub

C-44 www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

Contact Cavities and Assembly Instructions

Min. Max.

.188 (4.78) .208 (5.28)

Assembly Instructions

Wire-Stripping – Machine Contacts

1. Cut wires to length. Strip insulation per above illustration.

Check for frayed or broken wires.

2. Insert contact and wire into proper crimp tool (and locator, if

required). Crimp contact to wire. Inspect crimp.

3. Center wired contact into groove of insertion tool with

tool tip butting contact shoulder. Insert contact into cav-

ity until a positive stop is felt. Inspect insertion.

Contact Crimping Contact Insertion

Contact Extraction

4. To be sure contact is locked securely, pull back lightly on wire.

Repeat for balance of contacts working row by row across

the insulator.

5. Place wire into extraction tool tip. 6. Insert tool tip into contact cavity until tip bottoms against

contact shoulder, releasing tines. Hold wire against tool

with finger and remove tool and contact. Repeat for bal-

ance of contacts.

Contact Arrangements

Shell Size E A B

Contact Arrangement 9 15 25

Contact Size #20 #20 #20

Face View Pin Insert

(Use a mirror image for

receptacle).

37 50

#20 #20

Face View Pin Insert

(Use a mirror image for

receptacle).

Shell size EA B

Contact Arrangement 15 26 44

Contact Size #22 #22 #22

62 78

#22 #22

610

11 15

8101

6291

115

16 30

4413

121

120

21 39

Standard Density

High Density

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 44

D Sub

C-45

www.ittcannon.com

D*M Standard Density

Straight PCB Hole Pattern

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

5,49

(.216)

5,49

(.216)

5,49(.216)

8,23 (.324)

Mounting

Hole

Signal

Contact

2,74 (.108)

25,00 (.984)

2,54 (.100)

REAR FLANGE REF REAR FLANGE REF

10,90 (.429) 9,40 (.370)

33,32 (1.312)

8,23 (.324) 8,23 (.324)

5,49

(.216)

5,49

(.216)

5,49

(.216)

8,23 (.324)

6,86

(.270)

6,86

(.270)

9,60 (.378) 9,60 (.378)

Mounting

Hole

Signal

Contact 2,74 (.108)

2,54 (.100)

9,40 (.370)

10,90 (.429)

REAR FLANGE REF

5,54(.218) 5,54(.218)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

5,54(.218)

8,28 (.326)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

Mounting

Hole

Signal

Contact

2,80 (.110)

2,54 (.100)

9,40 (.370)

REAR FLANGE REF

10,70 (.421)

REAR FLANGE REF

47,04 (1.852)

5,54(.218) 5,54(.218)

23,47 (.924)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

5,54(.218)

8,28 (.326)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

12,42 (.489)

15,19 (.598)

17,96 (.707)

20.70 (.815)

17,96 (.707)

20,70 (.815)

6,91 (.272)

9,68 (.381)

Mounting

Hole

Signal

Contact

2,80 (.110)

23,47 (.924)

63,50 (2.500)

24,84 (.978) 24,84 (.978)

2,54 (.100)

9,40 (.370)

REAR FLANGE REF

10,90 (.429)

REAR FLANGE REF

9 Contacts

37 Contacts

15 Contacts

25 Contacts

50 Contacts

Signal Contact Recommended PCB Hole

0,60 (.024) 1,00 (.039)

Mounting Type Recommended PCB Hole

Without Boardlock 3,05 (.120)

With Boardlock 3,10 (.122)

Straight PCB Plug and Receptacle

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 45

D Sub

C-46 www.ittcannon.com

90° D*M

Standard Density

5,49

(.216) 5,49

(.216)

5,49(.216)

8,23 (.324)

Mounting

Hole

Signal

Contact

2,74 (.108)

25,00 (.984)

2,84 (.112)

7,19 (.283)

REAR FLANGE REF

8,64 (.340)

REAR FLANGE REF

5,54(.218) 5,54(.218)

23,47 (.924)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

5,54(.218)

8,28 (.326)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

12,42 (.489)

15,19 (.598)

17,96 (.707)

20.70 (.815)

17,96 (.707)

20,70 (.815)

6,91 (.272)

9,68 (.381)

Mounting

Hole

Signal

Contact

2,80 (.110)

23,47 (.924)

63,50 (2.500)

24,84 (.978) 24,84 (.978)

2,84 (.112)

7,19 (.283)

REAR FLANGE REF

8,64 (.340)

REAR FLANGE REF

33,32 (1.312)

8,23 (.324) 8,23 (.324)

5,49

(.216)

5,49

(.216) 5,49

(.216)

8,23 (.324)

6,86

(.270) 6,86

(.270)

9,60 (.378) 9,60 (.378)

Mounting

Hole

Signal

Contact 2,74 (.108)

2,54 (.100)

7,19 (.283)

8,64 (.340)

REAR FLANGE REF

5,54(.218) 5,54(.218)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

5,54(.218)

8,28 (.326)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

Mounting

Hole

Signal

Contact

2,80 (.110)

2,84 (.112)

7,19 (.283)

REAR FLANGE REF

8,64 (.340)

REAR FLANGE REF

47,04 (1.852)

25 Contacts

50 Contacts

9 Contacts

37 Contacts

15 Contacts

Signal Contact Recommended PCB Hole

0,76 (.030) 1,14 (.045)

1,00 (.040) 1,40 (.055)

Mounting Type Recommended PCB Hole

Without Boardlock 3,05 (.120)

With Boardlock 3,10 (.122)

5,54(.218) 5,54(.218)

23,47 (.924)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

22,10 (.870)

19,33 (.761)

16,56 (.652)

13,82 (.544)

11,05 (.435)

8,28 (.326)

5,54(.218)

8,28 (.326)

12,42 (.489)

15,19 (.598)

6,91 (.272)

9,68 (.381)

12,42 (.489)

15,19 (.598)

17,96 (.707)

20.70 (.815)

17,96 (.707)

20,70 (.815)

6,91 (.272)

9,68 (.381)

Mounting

Hole

Signal

Contact

2,80 (.110)

23,47 (.924)

63,50 (2.500)

24,84 (.978) 24,84 (.978)

2,84 (.112)

7,19 (.283)

REAR FLANGE REF

8,64 (.340)

REAR FLANGE REF

37 Contacts

90° Plug and Receptacle

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 46

D Sub

C-47

www.ittcannon.com

Straight PCB Hole Pattern

PCB Hole Pattern

D*MA High Density

24,99 (.984)

2,29 (.090)

2,04 (.080)

1,40 (.055)

0,89 (.035)

0,25 (.010)

33,32 (1.312)

2,29 (.090)

1,78 (.070) 0,51 (.020)

0,64 (.025) 1,65 (.065)

47,04 (1.852)

2,29 (.090)

1,78 (.070) 0,51 (.020)

0,64 (.025) 1,64 (.065)

63,50 (2.500)

1,63 (.064) 0,79 (.031)

0,42 (.0165)

2,41 (.095)

1,99 (0785)

61,11 (2.406)

2,41 (.095) 1,21 (.048)

63,50 (2.500)

1,83 (.072) 0,58 (.023)

0,62 (.024)

2,41 (.095

1,79 (070)

(Mating Side)

SIZE E

15 Contacts

SIZE A

26 Contacts

SIZE B

44 Contacts

SIZE C

62 Contacts

SIZE D

78 Contacts

SIZE F

104 Contacts

Face view, pin insert for plug

(use a mirror image for receptacle)

Dimension X

1,98 (.078) for sizes E, A, B, C

2,08 (.082) for size D

Recommended PC hole for signal contacts

?0,90 (.035) min for terminations ? 0,51 (.020)

?1,00 (.040) min for terminations ?0,57 (.022)

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 47

PCB Hole Pattern

D*MA High Density

C-48 www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

90° PCB Hole Pattern

24,99 (.984)

2,29 (.090)

2,04 (.080)

1,40 (.055)

0,89 (.035)

0,25 (.010)

33,32 (1.312)

2,29 (.090)

1,78 (.070) 0,51 (.020)

0,64 (.025) 1,65 (.065)

47,04 (1.852)

2,29 (.090)

1,78 (.070) 0,51 (.020)

0,64 (.025) 1,64 (.065)

63,50 (2.500)

1,63 (.064) 0,79 (.031)

0,42 (.0165)

2,41 (.095)

1,99 (0785)

61,11 (2.406)

2,41 (.095) 1,21 (.048)

63,50 (2.500)

1,83 (.072) 0,58 (.023)

0,62 (.024)

2,41 (.095

1,79 (070)

(Mating Side)

SIZE E

15 Contacts

SIZE A

26 Contacts

SIZE B

44 Contacts

SIZE C

62 Contacts

SIZE D

78 Contacts

SIZE F

104 Contacts

13,82 (0.544)

15.39 (0.606)

15.6 (0.614)

FROM REAR FLANGE SHELL REF

Face view, pin insert for plug

(use a mirror image for receptacle)

Dimension X

1,98 (.078) for sizes E, A, B, C

2,08 (.082) for size D

Recommended PC hole for signal contacts

?0,90 (.035) min for terminations ? 0,51 (.020)

?1,00 (.040) min for terminations ?0,57 (.022)

Recommended PCB mounting hole

?3.05 (.120)

D Sub

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 48

Panel Cutouts

Standard Panel Cutouts

Panel Cutouts

Standard Shell

Shell

Size

Mounting

Method

±0,13 (.005)

±0,05 (.002)

DE Front 22,19 (.874) 11,09 (.437) 24,99 (.984) 12,49 (.492) 13,03 (.513) 6,52 (.257) 3,04 (.120) 1,52 (.060) 2,10 (.083)

Rear 20,47 (.806) 10,23 (.403) 24,99 (.984) 12,49 (.492) 11,40 (.449) 5,71 (.225) 3,04 (.120) 1,52 (.060) 3,35 (.132)

DA Front 30,53 (1.202) 15,26 (.601) 33,32 (1.312) 16,66 (.656) 13,03 (.513) 6,52 (.257) 3,04 (.120) 1,52 (.060) 2,10 (.083)

Rear 28,80 (1.134) 14,40 (.567) 33,32 (1.312) 16,66 (.656) 11,40 (.449) 5,71 (.225) 3,04 (.120) 1,52 (.060) 3,35 (.132)

DB Front 44,27 (1.743) 22,14 (.872) 47,04 (1.852) 23,52 (.926) 13,03 (.513) 6,52 (.257) 3,04 (.120) 1,52 (.060) 2,10 (.083)

Rear 42,51 (1.674) 21,25 (.837) 47,04 (1.852) 23,52 (.926) 11,40 (.449) 5,71 (.225) 3,04 (.120) 1,52 (.060) 3,35 (.132)

DC Front 60,73 (2.391) 30,37 (1.196) 63,50 (2.500) 31,75 (1.250) 13,03 (.513) 6,52 (.257) 3,04 (.120) 1,52 (.060) 2,10 (.083)

Rear 59,08 (2.326) 29,54 (1.163) 63,50 (2.500) 31,75 (1.250) 11,40 (.449) 5,71 (.225) 3,04 (.120) 1,52 (.060) 3,35 (.132)

DD Front 58,34 (2.297) 29,18 (1.149) 61,11 (2.406) 30,55 (1.203) 15,82 (.623) 7,92 (.312) 3,04 (.120) 1,52 (.060) 2,10 (.083)

Rear 56,33 (2.218) 28,16 (1.109) 61,11 (2.406) 30,55 (1.203) 14,09 (.555) 7,06 (.278) 3,04 (.120) 1,52 (.060) 3,35 (.132)

Standard Cutout Rear Mounting Cutout (Optional)

Front Panel Mounting

llehS tnuoM taolF lauDllehS dradnatS

Rear Panel Mounting

llehS tnuoM taolF lauDllehS dradnatS

Dual Float Mount Shell

Shell

Size

Mounting

Method

±0,13 (.005)

±0,05 (.002)

DE Front 23,01 (.906) 11,50 (.453) 24,99 (.984) 12,49 (.492) 13,84 (.545) 6,93 (.273) 2,23 (.088) 1,11 (.044) 2,10 (.083)

Rear 21,28 (.838) 10,64 (.419) 24,99 (.984) 12,49 (.492) 12,21 (.481) 6,12 (.241) 2,23 (.088) 1,11 (.044) 3,35 (.132)

DA Front 31,34 (1.234) 15,67 (.617) 33,32 (1.312) 16,66 (.656) 13,84 (.545) 6,93 (.273) 2,23 (.088) 1,11 (.044) 2,10 (.083)

Rear 29,61 (1.166) 14,80 (.583) 33,32 (1.312) 16,66 (.656) 12,21 (.481) 6,12 (.241) 2,23 (.088) 1,11 (.044) 3,35 (.132)

DB Front 45,08 (1.775) 22,55 (.888) 47,04 (1.852) 23,52 (.926) 13,84 (.545) 6,93 (.273) 2,23 (.088) 1,11 (.044) 2,10 (.083)

Rear 43,33 (1.706) 21,66 (.853) 47,04 (1.852) 23,52 (.926) 12,21 (.481) 6,12 (.241) 2,23 (.088) 1,11 (.044) 3,35 (.132)

DC Front 61,54 (2.423) 30,78 (1.212) 63,50 (2.500) 31,75 (1.250) 13,84 (.545) 6,93 (.273) 2,23 (.088) 1,11 (.044) 2,10 (.083)

Rear 59,79 (2.354) 29,89 (1.177) 63,50 (2.500) 31,75 (1.250) 12,21 (.481) 6,12 (.241) 2,23 (.088) 1,11 (.044) 3,35 (.132)

DD Front 59,15 (2.329) 29,59 (1.165) 61,11 (2.406) 30,55 (1.203) 16,63 (.655) 8,33 (.328) 2,23 (.088) 1,11 (.044) 2,10 (.083)

Rear 57,15 (2.250) 28,57 (1.125) 61,11 (2.406) 30,55 (1.203) 14,90 (.587) 7,46 (.294) 2,23 (.088) 1,11 (.044) 3,35 (.132)

D Sub

C-49

www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 49

D Sub

C-50 www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

M24308 Cross Reference

Gov't Designa-

tion ITT Part Number

M24308/1-1Z DEMM9S

M24308/1-1F DEMM9S-A101

M24308/1-2Z DAMM15S

M24308/1-2F DAMM15S-A101

M24308/1-3Z DBMM25S

M24308/1-3F DBMM25S-A101

M24308/1-4Z DCMM37S

M24308/1-4F DCMM37S-A101

M24308/1-5Z DDMM50S

M24308/1-5F DDMM50S-A101

M24308/1-12Z DEMMY9S

M24308/1-12F DEMMY9S-A101

M24308/1-13Z DAMMY15S

M24308/1-13F DAMMY15S-A101

M24308/1-14Z DBMMY25S

M24308/1-14F DBMMY25S-A101

M24308/1-15Z DCMMY37S

M24308/1-15F DCMMY37S-A101

M24308/1-16Z DDMMY50S

M24308/1-16F DDMMY50S-A101

M24308/1-23Z DEMMY9S

M24308/1-23F DEMMY9S-A101

M24308/1-24Z DAMMY15S

M24308/1-24F DAMMY15S-A101

M24308/1-25Z DBMMY25S

M24308/1-25F DBMMY25S-A101

M24308/1-26Z DCMMY37S

M24308/1-26F DCMMY37S-A101

M24308/1-27Z DDMMY50S

M24308/1-27F DDMMY50S-A101

M24308/2-1Z DEMAM9S

M24308/2-1F DEMAM9S-A101

M24308/2-2Z DAMAM15S

M24308/2-2F DAMAM15S-A101

M24308/2-3Z DCMAM25S

M24308/2-3F DCMAM25S-A101

M24038/2-4Z DCMAM37S

M24308/2-4F DCMAM37S-A101

M24308/2-5Z DDMAM50S

M24308/2-5F DDMAM50S-A101

M24308/2-6Z DEMAMT9S

M24308/2-6F DEMAMT9S-A101

M24308/2-7Z DAMAMT15S

M24308/2-7F DAMAMT15S-A101

M24308/2-8Z DBMAMT25S

M24308/2-8F DBMAMT25S-A101

M24308/2-9Z DCMAMT37S

M24308/2-9F DCMAMT37S-A101

M24308/2-10Z DDMAMT50S

M24308/2-10F DDMAMT50S-A101

M24308/2-11Z DEMAM15S

M24308/2-11F DEMAM15S-A101

M24308/2-12Z DAMAM26S

M24308/2-12F DAMAM26S-A101

M24308/2-13Z DBMAM44S

M24308/2-13F DBMAM44S-A101

M24308/2-14Z DCMAM62S

M24308/2-14F DCMAM62S-A101

Gov't Desig-

nation ITT Part Number

M24308/2-15Z DDMAM78S

M24308/2-15F DDMAM78S-A101

M24308/2-17Z DEMAMT15S

M24308/2-17F DEMAMT15S-A101

M24308/2-18Z DAMAMT26S

M24308/2-18F DAMAMT26S-A101

M24308/2-19Z DBMAMT44S

M24308/2-19F DBMAMT44S-A101

M24308/2-20Z DCMAMT62S

M24308/2-20F DCMAMT62S-A101

M24308/2-21Z DDMAMT78S

M24308/2-21F DDMAMT78S-A101

M24308/2-23Z DEMAMY9S

M24308/2-23F DEMAMY9S-A101

M24308/2-24Z DAMAMY15S

M24308/2-24F DAMAMY15S-A101

M24308/2-25Z DBMAMY25S

M24308/2-25F DBMAMY25S-A101

M24308/2-26Z DCMAMY37S

M24308/2-26F DCMAMY37S-A101

M24308/2-27Z DDMAMY50S

M24308/2-27F DDMAMY50S-A101

M24308/2-28Z DEMAMY15S

M24308/2-28F DEMAMY15S-A101

M24308/2-29Z DAMAMY26S

M24308/2-29F DAMAMY26S-A101

M24308/2-30Z DBMAMY44S

M24308/2-30F DBMAMY44S-A101

M24308/2-31Z DCMAMY62S

M24308/2-31F DCMAMY62S-A101

M24308/2-32Z DDMAMY78S

M24308/2-32F DDMAMY78S-A101

M24308/2-34Z DEMAMYT9S

M24308/2-34F DEMAMYT9S-A101

M24308/2-35Z DAMAMYT15S

M24308/2-35F DAMAMYT15S-A101

M24308/2-36Z DBMAMYT25S

M24308/2-36F DBMAMYT25S-A101

M24308/2-37Z DCMAMYT37S

M24308/2-37F DCMAMYT37S-A101

M24308/2-38Z DDMAMYT50S

M24308/2-38F DDMAMYT50S-A101

M24308/2-39Z DEMAMYT15S

M24308/2-39F DEMAMYT15S-A101

M24308/2-40Z DAMAMYT26S

M24308/2-40F DAMAMYT26S-A101

M24308/2-41Z DBMAMYT44S

M24308/2-41F DBMAMYT44S-A101

M24308/2-42Z DCMAMYT62S

M24308/2-42F DCMAMYT62S-A101

M24308/2-43Z DDMAMYT78S

M24308/2-43F DDMAMYT78S-A101

M24308/2-281Z DEMAM9S-FO

M24308/2-281F DEMAM9S-A101-FO

M24308/2-282Z DAMAM15S-FO

M24308/2-282F DAMAM15S-A101-FO

M24308/2-283Z DBMAM25S-FO

M24308/2-283F DBMAM25S-A101-FO

Gov't Designa-

tion ITT Part Number

M24308/2-284Z DCMAM37S-FO

M24308/2-284F DCMAM37S-A101-FO

M24308/2-285Z DDMAM50S-FO

M24308/2-285F DDMAM50S-A101-FO

M24308/2-286Z DEMAM15S-FO

M24308/2-286F DEMAM15S-A101-FO

M24308/2-287Z DAMAM26S-FO

M24308/2-287F DAMAM26S-A101-FO

M24308/2-288Z DBMAM44S-FO

M24308/2-288F DBMAM44S-A101-FO

M24308/2-289Z DCMAM62S-FO

M24308/2-289F DCMAM62S-A101-FO

M24308/2-290Z DDMAM78S-FO

M24308/2-290F DDMAM78S-A101-FO

M24308/2-292Z DEMAMY9S-FO

M24308/2-292F DEMAMY9S-A101-FO

M24308/2-293Z DAMAMY15S-FO

M24308/2-293F DAMAMY15S-A101-FO

M24308/2-294Z DBMAMY25S-FO

M24308/2-294F DBMAMY25S-A101-FO

M24308/2-295Z DCMAMY37S-FO

M24308/2-295F DCMAMY37S-A101-FO

M24308/2-296Z DDMAMY50S-FO

M24308/2-296F DDMAMY50S-A101-FO

M24308/2-297Z DEMAMY15S-FO

M24308/2-297F DEMAMY15S-A101-FO

M24308/2-298Z DAMAMY26S-FO

M24308/2-298F DAMAMY26S-A101-FO

M24308/2-299Z DBMAMY44S-FO

M24308/2-299F DBMAMY44S-A101-FO

M24308/2-300Z DCMAMY62S-FO

M24308/2-300F DCMAMY62S-A101-FO

M24308/2-301Z DDMAMY78S-FO

M24308/2-301F DDMAMY78S-A101-FO

M24308/2-335Z DBMAMY25S

M24308/2-335F DBMAMY25S-A101

M24308/2-336Z DCMAMY37S

M24308/2-336F DCMAMY37S-A101

M24308/2-341Z DAMAMY15S

M24308/2-341F DAMAMY15S-A101

M24308/2-342Z DEMAMY9S

M24308/2-342F DEMAMY9S-A101

M24308/2-343Z DAMAMY15S

M24308/2-343F DAMAMY15S-A101

M24308/2-344Z DBMAMY25S

M24308/2-344F DBMAMY25S-A101

M24308/2-345Z DCMAMY37S

M24308/2-345F DCMAMY37S-A101

M24308/2-346Z DDMAMY50S

M24308/2-346F DDMAMY50S-A101

M24308/2-347Z DEMAMY15S

M24308/2-347F DEMAMY15S-A101

M24308/2-348Z DAMAMY26S

M24308/2-348F DAMAMY26S-A101

M24308/2-349Z DBMAMY44S

M24308/2-349F DBMAMY44S-A101

M24308/2-350Z DCMAMY62S

M24308/2-350F DCMAMY62S-A101

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 50

D Sub

C-51

www.ittcannon.com

Dimensions shown in inches (mm)

Specifications and dimensions subject to change

M24308 Cross Reference

Gov't Designa-

tion ITT Part Number

M24308/2-351Z DDMAMY78S

M24308/2-351F DDMAMY78S-A101

M24308/2-353Z DEMAMYT9S

M24308/2-353F DEMAMYT9S-A101

M24308/2-354Z DAMAMYT15S

M24308/2-354F DAMAMYT15S-A101

M24308/2-355Z DBMAMYT25S

M24308/2-355F DBMAMYT25S-A101

M24308/2-356Z DCMAMYT37S

M24308/2-356F DCMAMYT37S-A101

M24308/2-357Z DDMAMYT50S

M24308/2-357F DDMAMYT50S-A101

M24308/2-358Z DEMAMYT15S

M24308/2-358F DEMAMYT15S-A101

M24308/2-359Z DAMAMYT26S

M24308/2-359F DAMAMYT26S-A101

M24308/2-360Z DBMAMYT44S

M24308/2-360F DBMAMYT44S-A101

M24308/2-361Z DCMAMYT62S

M24308/2-361F DCMAMYT62S-A101

M24308/2-362Z DDMAMYT78S

M24308/2-362F DDMAMYT78S-A101

M24308/2-482Z DEMAMY9S-FO

M24308/2-482F DEMAMY9S-A101-FO

M24308/2-483Z DAMAMY15-S-FO

M24308/2-483F DAMAMY15-S-A101-FO

M24308/2-484Z DBMAMY25S-FO

M24308/2-484F DBMAMY25S-A101-FO

M24308/2-485Z DCMAMY37S-FO

M24308/2-485F DCMAMY37S-A101-FO

M24308/2-486Z DDMAMY50S-FO

M24308/2-486F DDMAMY50S-A101-FO

M24308/2-487Z DEMAMY15S-FO

M24308/2-487F DEMAMY15S-A101-FO

M24308/2-488Z DAMAMY26S-FO

M24308/2-488F DAMAMY26S-A101-FO

M24308/2-489Z DBMAMY44S-FO

M24308/2-489F DBMAMY44S-A101-FO

M24308/2-490Z DCMAMY62S-FO

M24308/2-490F DCMAMY62S-A101-FO

M24308/2-491Z DDMAMY78S-FO

M24308/2-491F DDMAMY78S-A101-FO

M24308/2-509Z DBMAMY25S

M24308/2-509F DBMAMY25S-A101

M24308/2-510Z DCMAMY37S

M24308/2-510F DCMAMY37S-A101

M24308/2-515Z DAMAMY15S

M24308/2-515F DAMAMY15S-A101

M24308/3-1Z DEMM9P

M24308/3-1F DEMM9P-A101

M24308/3-2Z DAMM15P

M24308/3-2F DAMM15P-A101

M24308/3-3Z DBMM25P

M24308/3-3F DBMM25P-A101

M24308/3-4Z DCMM37P

M24308/3-4F DCMM37P-A101

M24308/3-5Z DDMM50P

M24308/3-5F DDMM50P-A101

Gov't Designa-

tion ITT Part Number

M24308/3-12Z DEMMY-9P

M24308/3-12F DEMMY-9P-A101

M24308/3-13Z DAMMY-15P

M24308/3-13F DAMMY-15P-A101

M24308/3-14Z DBMMY-25P

M24308/3-14F DBMMY-25P-A101

M24308/3-15Z DCMMY-37P

M24308/3-15F DCMMY-37P-A101

M24308/3-16Z DDMMY-50P

M24308/3-16F DDMMY-50P-A101

M24308/3-17Z DEMMY-9P

M24308/3-17F DEMMY-9P-A101

M24308/3-18Z DAMMY-15P

M24308/3-18F DAMMY-15P-A101

M24308/3-19Z DBMMY-25P

M24308/3-19F DBMMY-25P-A101

M24308/3-20Z DCMMY-37P

M24308/3-20F DCMMY-37P-A101

M24308/3-21Z DDMMY-50P

M24308/3-21F DDMMY-50P-A101

M24308/4-1Z DEMAM9P

M24308/4-1F DEMAM9P-A101

M24308/4-2Z DAMAM15P

M24308/4-2F DAMAM15P-A101

M24308/4-3Z DBMAM25P

M24308/4-3F DBMAM25P-A101

M24308/4-4Z DCMAM37P

M24308/4-4F DCMAM37P-A101

M24308/4-5Z DDMAM50P

M24308/4-5F DDMAM50P-A101

M24308/4-6Z DEMAMT9P

M24308/4-6F DEMAMT9P-A101

M24308/4-7Z DAMAMT15P

M24308/4-7F DAMAMT15P-A101

M24308/4-8Z DBMAMT25P

M24308/4-8F DBMAMT25P-A101

M24308/4-9Z DCMAMT37P

M24308/4-9F DCMAMT37P-A101

M24308/4-10Z DDMAMT50P

M24308/4-10F DDMAMT50P-A101

M24308/4-11Z DEMAM15P

M24308/4-11F DEMAM15P-A101

M24308/4-12Z DAMAM26P

M24308/4-12F DAMAM26P-A101

M24308/4-13Z DBMAM44P

M24308/4-13F DBMAM44P-A101

M24308/4-14Z DCMAM62P

M24308/4-14F DCMAM62P-A101

M24308/4-15Z DDMAM78P

M24308/4-15F DDMAM78P-A101

M24308/4-17Z DEMAMT15P

M24308/4-17F DEMAMT15P-A101

M24308/4-18Z DAMAMT26P

M24308/4-18F DAMAMT26P-A101

M24308/4-19Z DBMAMT44P

M24308/4-19F DBMAMT44P-A101

M24308/4-20Z DCMAMT62P

M24308/4-20F DCMAMT62P-A101

Gov't Designa-

tion ITT Part Number

M24308/4-21Z DDMAMT78P

M24308/4-21F DDMAMT78P-A101

M24308/4-259Z DEMAM9P-FO

M24308/4-259F DEMAM9P-A101-FO

M24308/4-260Z DAMAM15P-FO

M24308/4-260F DAMAM15P-A101-FO

M24308/4-261Z DBMAM25P-FO

M24308/4-261F DBMAM25P-A101-FO

M24308/4-262Z DCMAM37P-FO

M24308/4-262F DCMAM37P-A101-FO

M24308/4-263Z DDMAM50P-FO

M24308/4-263F DDMAM50P-A101-FO

M24308/4-264Z DEMAM15P-FO

M24308/4-264F DEMAM15P-A101-FO

M24308/4-265Z DAMAM26P-FO

M24308/4-265F DAMAM26P-A101-FO

M24308/4-266Z DBMAM44P-FO

M24308/4-266F DBMAM44P-A101-FO

M24308/4-267Z DCMAM62P-FO

M24308/4-267F DCMAM62P-A101-FO

M24308/4-268Z DDMAM78P-FO

M24308/4-268F DDMAM78P-A101-FO

M24308/4-302Z DEMAMY9P

M24308/4-302F DEMAMY9P-A101

M24308/4-303Z DAMAMY15P

M24308/4-303F DAMAMY15P-A101

M24308/4-304Z DBMAMY25P

M24308/4-304F DBMAMY25P-A101

M24308/4-305Z DCMAMY37P

M24308/4-305F DCMAMY37P-A101

M24308/4-306Z DDMAMY50P

M24308/4-306F DDMAMY50P-A101

M24308/4-307Z DEMAMY15P

M24308/4-307F DEMAMY15P-A101

M24308/4-308Z DAMAMY26P

M24308/4-308F DAMAMY26P-A101

M24308/4-309Z DBMAMY44P

M24308/4-309F DBMAMY44P-A101

M24308/4-310Z DCMAMY62P

M24308/4-310F DCMAMY62P-A101

M24308/4-311Z DDMAMY78P

M24308/4-311F DDMAMY78P-A101

M24308/4-313Z DEMAMYT9P

M24308/4-313F DEMAMYT9P-A101

M24308/4-314Z DAMAMYT15P

M24308/4-314F DAMAMYT15P-A101

M24308/4-315Z DBMAMYT25P

M24308/4-315F DBMAMYT25P-A101

M24308/4-316Z DCMAMYT37P

M24308/4-316F DCMAMYT37P-A101

M24308/4-317Z DDMAMYT50P

M24308/4-317F DDMAMYT50P-A101

M24308/4-318Z DEMAMYT15P

M24308/4-318F DEMAMYT15P-A101

M24308/4-319Z DAMAMYT26P

M24308/4-319F DAMAMYT26P-A101

M24308/4-320Z DBMAMYT44P

M24308/4-320F DBMAMYT44P-A101

ca_C1-C61.qxd:Layout 1 2/10/11 9:32 AM Page 51