Thick Film Chip Resistors MCR Series < Automotive > Features 1) Full line up from ultra small size (01005) to 2512 with jumper type. 2) High reliability metal glazed thick film. 3) ROHM resistors have obtained ISO9001/ISO/TS16949 certification. 4) "Automotive" product is AEC-Q200 compliant. Size Part No. MCR004 (mm) 0402 Type Code (inch) Packing Specification Quantity / Reel - Paper tape (2mm pitch) 15,000 RZP - Embossed tape (1mm pitch) 40,000 YRT YZP MRT MZP GENERAL PURPOSE AUTOMOTIVE Corresponds to AEC-Q200 YZP 01005 MCR006 0603 0201 MCR01 1005 0402 10,000 PZPI (*For further information on datasheet, please refer to AUTOMOTIVE datasheet.) EZP ERT MCR03 1608 0603 MZP / PZPI (*For further information on datasheet, please refer to AUTOMOTIVE datasheet.) MCR10 2012 0805 ERT EZP MCR18 3216 1206 ERT EZP MCR25 3225 1210 JZH MCR50 5025 2010 JZH MCR100 6432 2512 JZH 15,000 Paper tape (2mm pitch) Bulk case 50,000 Paper tape (4mm pitch) 5,000 MZP : Paper tape (2mm pitch) PZPI : Bulk case MZP : 10,000 PZPI : 25,000 Paper tape (4mm pitch) 5,000 Embossed tape (4mm pitch) 4,000 Please contact us for status of AEC-Q200 on "General purpose" products. Part Number Description M C R 0 0 6 Part No. Size (mm [inch]) MCR 004 (0402 [01005]) 006 (0603 [0201]) 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) 25 (3225 [1210]) 50 (5025 [2010]) 100 (6432 [2512]) (Micro chip resistors) www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. Y R T Type Code J 1 0 0 Resistance Tolerance Nominal Resistance D ( 0.5% ) F ( 1% ) FX ( 1% ) Only MCR03EZP/MZP/PZPI J ( 5% ) (Including jumper type) Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance D,F J Resistance code : : 4 digits 3 digits Ex.) 1 = 1R0 ( 5% ) 9.1 = 9R1 ( 5% ) 10 = 10R0 ( 0.5%,1% ) 100 ( 5% ) 2.2M = 2204 ( 1% ) 225 ( 5% ) 1/6 2012.11 - Rev.D MCR series < Automotive > Data Sheet Products List Part No. Type Code Rated Power Limiting Element (70C) Voltage (W) MCR006 YZP 0.05 (V) 25 Maximum Overload Voltage (V) - Temperature Resistance Coefficient Tolerance (ppm / C) +600 / -200 250 250 200 100 Resistance Range Series Operating Temperature Range (C) 1.0 to 9.1 10 to 10M 10 to 10M 10 to 910 1k to 1M E24 -55 to +125 (%) J(5%) F(1%) D(0.5%) Jumper type : Rmax = 50m / Imax. = 0.5A MCR01 MCR03 MZP PZPI EZP MZP PZPI 0.063 0.1 50 50 0.125 MCR10 150 EZP 0.1 - +500 / -250 200 100 100 50 J(5%) F(1%) D(0.5%) 1.0 to 9.1 10 to 10M 10 to 2.2M 10 to 91 100 to 1M Jumper type : Rmax = 50m / Imax. = 1A 400 1.0 to 9.1 J(5%) 200 10 to 10M FX(1%) 100 10 to 10M 100 100 10 to 91 D(0.5%) 50 100 to 1M Jumper type : Rmax = 50m / Imax. = 1A 400 1.0 to 9.1 J(5%) 200 200 10 to 10M 100 10 to 2.2M F(1%) 100 10 to 91 300 D(0.5%) 50 100 to 1M E24 E24,E96 E24 E24 E24,E96 E24 E24,E96 Jumper type : Rmax = 50m / Imax. = 2A 0.25 MCR18 200 EZP 400 0.125 400 200 100 100 50 J(5%) F(1%) D(0.5%) 1.0 to 9.1 10 to 10M 10 to 2.2M 10 to 91 100 to 1M -55 to +155 E24 E24,E96 Jumper type : Rmax = 50m / Imax. = 2A 500350 MCR25 JZH 0.25 200 400 500 200 100 MCR50 MCR100 JZH JZH 0.5 1 200 200 1.0 to 2.0 J(5%) 2.2 to 5.1 E24 5.6 to 3.3M F(1%) 10 to 1M Jumper type : Rmax = 50m / Imax. = 2A 1.0 to 2.0 500350 2.2 to 9.1 500 J(5%) 10 to 330k 200 400 360k to 560k 350 10 to 180k 100 F(1%) Jumper type : Rmax = 50m / Imax. = 3A 1.0 to 2.0 500350 2.2 to 9.1 500 J(5%) 10 to 22 350 400 24 to 100k 200 10 to 82k 100 F(1%) E24,E96 E24 E24,E96 E24 -55 to +125 E24,E96 Jumper type : Rmax = 50m / Imax. = 4A Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 2/6 2012.11 - Rev.D MCR series < Automotive > Data Sheet Chip Resistor Dimensions and Markings MCR004 / 006 / 01 / 03 L 103 MCR10 / 18 / 25 / 50 / 100 L a a W W a <Marking method> There are three or four digits used for the calculation number according to IEC code and "R"is used for the decimal point. t t b b b (Unit : mm) Part No. Type Code (mm) (inch) L W t a b Marking existence MCR006 YZP 0603 0201 0.60.03 0.30.03 0.230.03 0.10.05 0.150.05 No MCR01 MZP PZPI 1005 0402 1.00.05 0.50.05 0.350.05 0.20.1 +0.05 0.25 -0.1 No MCR03 EZP MZP PZPI 1608 0603 1.60.1 0.80.1 0.450.1 0.30.2 0.30.2 Yes MCR10 EZP 2012 0805 2.00.1 1.250.1 0.550.1 0.40.2 0.40.2 Yes MCR18 EZP 3216 1206 3.20.15 1.60.15 0.550.1 0.50.25 0.50.25 Yes MCR25 JZH 3225 1210 3.20.15 2.50.15 0.550.15 0.50.25 0.50.25 Yes MCR50 JZH 5025 2010 5.00.15 2.50.15 0.550.15 0.60.25 0.60.25 Yes MCR100 JZH 6432 2512 6.30.15 3.20.15 0.550.15 0.60.25 0.60.25 Yes Marking method of jumper type Jumper type MCR006 / 01 / 25 / 50 / 100 MCR03 / 10 / 18 Marking existence No Yes Marking method of MCR03 For MCR03 series resistors, the printing process restricts the marking to three digits/characters. Consequently, 1% tolerance resistors with values from the E24 series will be marked the same as 5% resistors with the same value, but 1% tolerance resistors with values from the E96 series will not be marked. Examples: MCR03EZPJ243 MCR03EZPFX2402 MCR03EZPFX2432 (5% tolerance, E24 / 24 k ) (1% tolerance, E24 / 24 k ) (1% tolerance, E96 / 24.3 k ) Marking = 243 Marking = 243 No Marking MCR18EZPJ243 MCR18EZPF2402 MCR18EZPF2432 (5% tolerance, E24 / 24 k ) (1% tolerance, E24 / 24 k ) (1% tolerance, E96 / 24.3 k ) Marking = 243 Marking = 2402 Marking = 2432 Land pattern Example (Unit : mm) Dimensions Part No. MCR006 B MCR01 D MCR03 Land C A www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 3/6 Type Code A B C D YZP 0.3 0.84 0.3 0.27 0.5 1.3 0.5 0.4 1.0 2.0 0.8 0.5 MZP PZPI EZP MZP PZPI MCR10 EZP 1.2 2.6 1.15 0.7 MCR18 EZP 2.2 4.0 1.5 0.9 MCR25 JZH 2.2 4.0 2.3 0.9 MCR50 JZH 3.8 6.0 2.3 1.1 MCR100 JZH 5.1 8.1 3.0 1.5 2012.11 - Rev.D MCR series < Automotive > Data Sheet Derating Curve When the ambient temperature exceeds 70C, power dissipation must be adjusted according to the derating curves below. MCR006 / 100 PERCENT RATED POWER (%) PERCENT RATED POWER (%) 80 60 40 20 0 MCR01 / 03 / 10 / 18 / 25 / 50 100 100 -55 0 70 100 80 60 40 20 0 125 -55 0 AMBIENT TEMPERATURE (C) 70 100 155 AMBIENT TEMPERATURE (C) Characteristics Guaranteed Value Resistor Type Jumper Type Test Items Test Conditions Resistance See "Products List" 20C Variation of resistance with temperature See "Products List" Measurement : +20 / -55 / +20 / +125C (2.0%+0.1) Overload Rated voltage (current) x2.5, 2s. Maximum overload voltage Max. 50m A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability (1.0%+0.05) Resistance to soldering heat Max. 50m No remarkable abnormality on the appearance. Rosin*Ethanol : 25% (Weight) Soldering condition : 2355C Duration of immersion : 2.00.5s Soldering condition : 2605C Duration of immersion : 101s Rapid change of temperature (1.0%+0.05) Max. 50m Test temp. -55C to +125C 100cycle (MCR006 / 01 / 03) -55C to +125C 5cycle (MCR10 / 18 / 25 / 50 / 100) Damp heat, steady state (3.0%+0.1) Max. 100m 40C, 93%RH (Relative Humidity) Test time : 1,000h to 1,048h Endurance at 70C (3.0%+0.1) Max. 100m 70C Rated voltage (current) 1.5h : ON - 0.5h : OFF Test time : 1,000h to 1,048h Endurance (3.0%+0.1) Max. 100m 125C (MCR006 / 25 / 50 / 100) 155C (MCR01 / 03 / 10 / 18) Test time : 1,000h to 1,048h Resistance to solvent (1.0%+0.05) Max. 50m 235C, Immersion cleaning, 50.5min Solvent : 2-propanol (1.0%+0.05) Max. 50m Bend strength of the end face plating - Without mechanical damage such as breaks. Compliance Standard(s) : IEC60115-8 JISC 5201-8 Chip weight (typical value) Parameter Unit MCR006 YZP Weight mg/pc 0.157 MCR01 MCR03 MZP / PZPI EZP / MZP / PZPI 0.70 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 2.12 MCR10 EZP MCR18 EZP MCR25 JZH MCR50 JZH MCR100 JZH 5.03 9.46 16.5 25.8 42.0 4/6 2012.11 - Rev.D MCR series < Automotive > Data Sheet Tape Dimensions Paper Tape (Unit : mm) P0 P2 P1 Part No. Type Code W F E A0 B0 MCR006 YZP 8.00.2 3.50.05 1.750.1 0.380.03 0.680.03 MCR01 MZP 8.00.3 3.50.05 1.750.1 0.70.1 1.20.1 MCR03 EZP 8.00.3 3.50.05 1.750.1 1.10.1 1.90.1 MCR10 EZP 8.00.3 3.50.05 1.750.1 1.65 +0.2 -0.1 2.4 +0.2 -0.1 MCR18 EZP 8.00.3 3.50.05 1.750.1 1.95 +0.1 -0.05 3.5 +0.15 -0.05 Part No. Type Code D0 P0 P1 P2 T2 MCR006 YZP 1.5 +0.1 0 4.00.1 2.00.05 2.00.05 Max 0.5 MCR01 MZP 1.5 +0.1 0 4.00.1 2.00.05 2.00.05 Max 1.1 MCR03 EZP 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 MCR10 EZP 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 MCR18 EZP 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 Part No. Type Code W F E A0 B0 8.00.3 3.50.05 1.750.1 1.10.1 1.90.1 D0 P0 P1 P2 T2 4.00.1 2.00.5 2.00.05 Max 1.1 D0 E F W B0 A0 Top tape Base paper (Bottom tape) Components Cavity T2 Paper Tape (Narrow pitch taping) (Unit : mm) P0 0 D P2 E F A0 W MCR03 MZP B0 1.5 +0.1 0 P1 Top tape Base paper (Bottom tape) Components Cavity T2 Embossed Tape (Unit : mm) Part No. Type Code W F E A0 B0 MCR25 JZH 8.00.3 3.50.05 1.750.1 3.00.1 3.50.1 MCR50 JZH 120.3 5.50.05 1.750.1 3.40.2 5.60.2 MCR100 JZH 120.3 5.50.05 1.750.1 3.50.2 6.70.2 Part No. Type Code D0 P0 P1 P2 T2 MCR25 JZH 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 MCR50 JZH 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 MCR100 JZH 1.5 +0.1 0 4.00.1 4.00.1 2.00.05 Max 1.1 B0 W F D 0 P2 E P0 A0 P1 T2 www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. 5/6 2012.11 - Rev.D MCR series < Automotive > Data Sheet 02 04 06 08 06 D 04 B 02 A 08 Reel Dimensions C Label ACCORDING EIAJ ET-7200B (Unit : mm) Part No. Type Code MCR006 YZP MCR01 MZP MCR03 EZP MZP MCR10 EZP MCR18 EZP MCR25 JZH MCR50 JZH MCR100 JZH A B 0 180 -1.5 +1.0 60 0 C 9 D +1.0 0 13 130.2 +1.0 0 Bulk case Dimensions MCR01PZPI MCR03PZPI Slider Shutter 12.00.1 36 0 -0.2 1100.7 EIAJ ET-7200B compliant www.rohm.com c 2012 ROHM Co., Ltd. All rights reserved. (Unit : mm) 6/6 2012.11 - Rev.D Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. R1120A