HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E (R) Data Sheet November 4, 2005 15kV, ESD-Protected, +5V Powered, RS-232 Transmitters/Receivers FN4315.16 Features * Pb-Free Plus Anneal Available (RoHS Compliant) The HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E family of RS-232 transmitters/receivers interface circuits meet all ElA high-speed RS-232E and V.28 specifications, and are particularly suited for those applications where 12V is not available. A redesigned transmitter circuit improves data rate and slew rate, which makes this suitable for ISDN and high speed modems. The transmitter outputs and receiver inputs are protected to 15kV ESD (Electrostatic Discharge). They require a single +5V power supply and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply. The family of devices offers a wide variety of high-speed RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). * High Speed ISDN Compatible . . . . . . . . . . . . . 230kbits/s * ESD Protection for RS-232 I/O Pins to 15kV (IEC61000) * Meets All RS-232E and V.28 Specifications * Requires Only 0.1F or Greater External Capacitors * Two Receivers Active in Shutdown Mode (HIN213E) * Requires Only Single +5V Power Supply * Onboard Voltage Doubler/Inverter * Low Power Consumption (Typ) . . . . . . . . . . . . . . . . . 5mA * Low Power Shutdown Function (Typ) . . . . . . . . . . . . .1A * Three-State TTL/CMOS Receiver Outputs The HIN206E, HIN211E and HIN213E feature a low power shutdown mode to conserve energy in battery powered applications. In addition, the HIN213E provides two active receivers in shutdown mode allowing for easy "wakeup" capability. * Multiple Drivers - 10V Output Swing for +5V Input - 300 Power-Off Source Impedance - Output Current Limiting - TTL/CMOS Compatible The drivers feature true TTL/CMOS input compatibility, slew rate-limited output, and 300 power-off source impedance. The receivers can handle up to 30V input, and have a 3k to 7k input impedance. The receivers also feature hysteresis to greatly improve noise rejection. * Multiple Receivers - 30V Input Voltage Range - 3k to 7k Input Impedance - 0.5V Hysteresis to Improve Noise Rejection Applications * Any System Requiring High-Speed RS-232 Communications Port - Computer - Portable, Mainframe, Laptop - Peripheral - Printers and Terminals - Instrumentation, UPS - Modems, ISDN Terminal Adaptors Selection Table LOW POWER SHUTDOWN/TTL THREE-STATE NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN 4 Capacitors No/No 0 4 Capacitors Yes/Yes 0 3 4 Capacitors No/No 0 4 4 4 Capacitors No/No 0 4 5 4 Capacitors Yes/Yes 0 POWER SUPPLY VOLTAGE NUMBER OF RS-232 DRIVERS NUMBER OF RS-232 RECEIVERS NUMBER OF 0.1F EXTERNAL CAPACITORS HIN202E +5V 2 2 HIN206E +5V 4 3 HIN207E +5V 5 HIN208E +5V HIN211E +5V PART NUMBER HIN213E +5V 4 5 4 Capacitors Yes/Yes 2 HIN232E +5V 2 2 4 Capacitors No/No 0 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2003-2005. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Ordering Information PART NO. PART MARKING Ordering Information (Continued) TEMP. RANGE (C) PACKAGE PKG. DWG. # HIN202ECB HIN202ECB 0 to 70 16 Ld SOIC (W) M16.3 HIN202ECB-T HIN202ECB 16 Ld SOIC (W) Tape and M16.3 Reel HIN202ECBZ (Note) 202ECBZ HIN202ECBZ-T (Note) 202ECBZ HIN202ECBN HIN202ECBN 0 to 70 16 Ld SOIC (N) M16.15 HIN202ECBN-T HIN202ECBN 16 Ld SOIC (N) Tape and M16.15 Reel HIN202ECBNZ (Note) 202ECBNZ HIN202ECBNZ-T 202ECBNZ (Note) 0 to 70 16 Ld SOIC (W) M16.3 (Pb-free) 16 Ld SOIC (W) Tape and M16.3 Reel (Pb-free) 0 to 70 16 Ld SOIC (N) M16.15 (Pb-free) 16 Ld SOIC (N) Tape and M16.15 Reel (Pb-free) HIN202ECP HIN202ECP 0 to 70 16 Ld PDIP E16.3 HIN202ECPZ (Note) 202ECPZ 0 to 70 16 Ld PDIP* (Pb-free) E16.3 HIN202EIB HIN202EIB -40 to 85 16 Ld SOIC (W) M16.3 HIN202EIB-T HIN202EIB 16 Ld SOIC (W) Tape and M16.3 Reel HIN202EIBZ (Note) 202EIBZ -40 to 85 16 Ld SOIC (W) M16.3 (Pb-free) HIN202EIBZ-T (Note) 202EIBZ 16 Ld SOIC (W) Tape and M16.3 Reel (Pb-free) HIN202EIBN HIN202EIBN -40 to 85 16 Ld SOIC (N) M16.15 HIN202EIBN-T HIN202EIBN 16 Ld SOIC (N) Tape and M16.15 Reel HIN202EIBNZ (Note) 202EIBNZ HIN202EIBNZ-T 202EIBNZ (Note) -40 to 85 16 Ld SOIC (N) M16.15 (Pb-free) 16 Ld SOIC (N) Tape and M16.15 Reel (Pb-free) PART NO. PART MARKING TEMP. RANGE (C) PACKAGE PKG. DWG. # HIN206EIAZA-T HIN206EIAZ (Note) 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN207ECA-T HIN207ECA 24 Ld SSOP Tape and Reel M24.209 HIN207ECAZ (Note) HIN207ECAZ 0 to 70 24 Ld SSOP (Pb-free) M24.209 HIN207ECAZ-T (Note) HIN207ECAZ 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN207ECB HIN207ECB 0 to 70 24 Ld SOIC M24.3 HIN207ECB-T HIN207ECB 24 Ld SOIC Tape and Reel M24.3 HIN207ECBZ (Note) HIN207ECBZ 0 to 70 24 Ld SOIC (Pb-free) M24.3 HIN207ECBZ-T (Note) HIN207ECBZ 24 Ld SOIC Tape and Reel (Pb-free) M24.3 HIN207EIA HIN207EIA -40 to 85 24 Ld SSOP M24.209 HIN207EIAZ (Note) HIN207EIAZ -40 to 85 24 Ld SSOP (Pb-free) M24.209 HIN207EIAZ-T (Note) HIN207EIAZ 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN207EIB HIN207EIB -40 to 85 24 Ld SOIC M24.3 HIN207EIB-T HIN207EIB 24 Ld SOIC Tape and Reel M24.3 HIN207EIBZ (Note) HIN207EIBZ -40 to 85 24 Ld SOIC (Pb-free) M24.3 HIN207EIBZ-T (Note) HIN207EIBZ 24 Ld SOIC Tape and Reel (Pb-free) M24.3 HIN208ECA HIN208ECA 0 to 70 24 Ld SSOP M24.209 HIN208ECA-T HIN208ECA 24 Ld SSOP Tape and Reel M24.209 HIN208ECAZ (Note) HIN208ECAZ 0 to 70 24 Ld SSOP (Pb-free) M24.209 HIN206ECB HIN206ECB 0 to 70 24 Ld SOIC M24.3 HIN206ECB-T HIN206ECB 24 Ld SOIC Tape and Reel M24.3 HIN208ECAZ-T (Note) HIN208ECAZ 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN206ECBZ (Note) HIN206ECBZ 0 to 70 24 Ld SOIC (Pb-free) M24.3 HIN208ECAZA-T HIN208ECAZ 24 Ld SSOP Tape and (Note) Reel (Pb-free) M24.209 HIN206ECBZ-T (Note) HIN206ECBZ 24 Ld SOIC Tape and Reel (Pb-free) M24.3 HIN208ECB HIN208ECB 0 to 70 24 Ld SOIC M24.3 HIN208ECB-T HIN208ECB M24.3 HIN206EIA HIN206EIA -40 to 85 24 Ld SSOP M24.209 24 Ld SOIC Tape and Reel HIN206EIAZ (Note) HIN206EIAZ -40 to 85 24 Ld SSOP (Pb-free) M24.209 HIN208ECBZ (Note) HIN208ECBZ 0 to 70 24 Ld SOIC (Pb-free) M24.3 HIN206EIAZ-T (Note) HIN206EIAZ 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN208ECBZ-T (Note) HIN208ECBZ 24 Ld SOIC Tape and Reel (Pb-free) M24.3 HIN206EIAZA (Note) HIN206EIAZ -40 to 85 24 Ld SSOP (Pb-free) M24.209 HIN208EIA HIN208EIA -40 to 85 24 Ld SSOP M24.209 HIN208EIA-T HIN208EIA 24 Ld SSOP Tape and Reel M24.209 2 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Ordering Information (Continued) PART NO. PART MARKING TEMP. RANGE (C) PACKAGE Ordering Information (Continued) PKG. DWG. # HIN208EIAZ (Note) HIN208EIAZ -40 to 85 24 Ld SSOP (Pb-free) M24.209 HIN208EIAZ-T (Note) HIN208EIAZ 24 Ld SSOP Tape and Reel (Pb-free) M24.209 HIN208EIB HIN208EIB -40 to 85 24 Ld SOIC HIN208EIBZ (Note) HIN208EIBZ -40 to 85 24 Ld SOIC (Pb-free) HIN211ECA HIN211ECA 0 to 70 28 Ld SSOP M28.209 HIN211ECA-T HIN211ECA 28 Ld SSOP Tape and Reel M28.209 HIN211ECAZ (Note) HIN211ECAZ 0 to 70 28 Ld SSOP (Pb-free) M28.209 HIN211ECAZ-T (Note) HIN211ECAZ 28 Ld SSOP Tape and Reel (Pb-free) HIN211ECB HIN211ECB HIN211ECBZ (Note) HIN211ECBZ PART NO. PART MARKING TEMP. RANGE (C) PACKAGE PKG. DWG. # HIN232ECA HIN232ECA 0 to 70 16 Ld SSOP M16.209 HIN232ECA-T HIN232ECA 16 Ld SSOP Tape and Reel M16.209 HIN232ECAZ-T (Note) HIN232ECAZ 16 Ld SSOP Tape and Reel (Pb-free) M16.209 M24.3 M24.3 HIN232ECB HIN232ECB 0 to 70 16 Ld SOIC (W) M16.3 HIN232ECB-T HIN232ECB 16 Ld SOIC (W) Tape and M16.3 Reel HIN232ECBN HIN232ECBN 0 to 70 16 Ld SOIC (N) M16.15 HIN232ECBN-T HIN232ECBN 16 Ld SOIC (N) Tape and M16.15 Reel HIN232ECBNZ (Note) 232ECBNZ M28.209 0 to 70 16 Ld SOIC (N) M16.15 (Pb-free) 0 to 70 28 Ld SOIC M28.3 HIN232ECBNZ-T 232ECBNZ (Note) 16 Ld SOIC (N) Tape and M16.15 Reel (Pb-free) 0 to 70 28 Ld SOIC (Pb-free) M28.3 HIN232ECBZ (Note) 232ECBZ 0 to 70 16 Ld SOIC (W) M16.3 (Pb-free) HIN211ECBZ-T (Note) HIN211ECBZ 28 Ld SOIC Tape and Reel (Pb-free) M28.3 HIN232ECBZ-T (Note) 232ECBZ 16 Ld SOIC (W) Tape and M16.3 Reel (Pb-free) HIN211EIA HIN211EIA -40 to 85 28 Ld SSOP M28.209 HIN232ECP HIN232ECP 0 to 70 16 Ld PDIP E16.3 HIN211EIA-T HIN211EIA 28 Ld SSOP Tape and Reel M28.209 HIN232ECPZ (Note) HIN232ECPZ 0 to 70 16 Ld PDIP* (Pb-free) E16.3 HIN211EIAZ (Note) HIN211EIAZ -40 to 85 28 Ld SSOP (Pb-free) M28.209 HIN232EIBN HIN232EIBN -40 to 85 16 Ld SOIC (N) M16.15 HIN232EIBN-T HIN211EIAZ-T (Note) HIN211EIAZ 28 Ld SSOP Tape and Reel (Pb-free) M28.209 HIN232EIBN 16 Ld SOIC (N) Tape and M16.15 Reel HIN211EIB -40 to 85 28 Ld SOIC M28.3 HIN232EIBNZ (Note) 232EIBNZ HIN211EIB -40 to 85 16 Ld SOIC (N) M16.15 (Pb-free) HIN211EIBZ (Note) HIN211EIBZ -40 to 85 28 Ld SOIC (Pb-free) M28.3 HIN232EIBNZ-T 232EIBNZ (Note) 16 Ld SOIC (N) Tape and M16.15 Reel (Pb-free) HIN213ECA HIN213ECA 0 to 70 28 Ld SSOP M28.209 HIN232EIV HIN232EIV -40 to 85 16 Ld TSSOP M16.173 HIN213ECA-T HIN213ECA 28 Ld SSOP Tape and Reel M28.209 HIN232EIV-T HIN232EIV 16 Ld TSSOP Tape and Reel M16.173 HIN213ECAZ (Note) HIN213ECAZ 0 to 70 28 Ld SSOP (Pb-free) M28.209 HIN232EIVZ (Note) 232EIVZ -40 to 85 16 Ld TSSOP (Pb-free) M16.173 HIN213ECAZ-T (Note) HIN213ECAZ 28 Ld SSOP Tape and Reel (Pb-free) M28.209 HIN232EIVZ-T (Note) 232EIVZ 16 Ld TSSOP Tape and Reel (Pb-free) M16.173 HIN213EIA HIN213EIA -40 to 85 28 Ld SSOP M28.209 HIN213EIA-T HIN213EIA 28 Ld SSOP Tape and Reel M28.209 *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. HIN213EIAZ (Note) HIN213EIAZ -40 to 85 28 Ld SSOP (Pb-free) M28.209 HIN213EIAZ-T (Note) HIN213EIAZ 28 Ld SSOP Tape and Reel (Pb-free) M28.209 HIN213EIB HIN213EIB -40 to 85 28 Ld SOIC M28.3 HIN213EIBZ (Note) HIN213EIBZ -40 to 85 28 Ld SOIC (Pb-free) M28.3 3 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts HIN202E (PDIP, SOIC) TOP VIEW HIN206E (SOIC, SSOP) TOP VIEW T3OUT 1 24 T4OUT 15 GND T1OUT 2 23 R2IN 14 T1OUT T2OUT 3 22 R2OUT R1IN 4 21 SD R1OUT 5 20 EN T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN 16 VCC C1+ 1 V+ 2 C1- 3 13 R1IN C2+ 4 12 R1OUT C2- 5 6 11 T1IN T2OUT 7 10 T2IN V- 9 R2OUT R2IN 8 C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ +5V 9 +5V 16 1 0.1F + 3 4 0.1F T1IN T2IN + 5 C1+ C1C2+ C2- 0.1F VCC +5V TO 10V VOLTAGE INVERTER V+ +10V TO -10V VOLTAGE INVERTER 2 + 0.1F V- 6 + +5V 400k T1 11 T2 10 +5V 400k 14 7 12 0.1F 0.1F T1OUT T2OUT T1IN T2IN T3IN T4IN 13 R1IN R1OUT 9 8 5k R2 +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER V- 15 T1 +5V 400k T2 6 18 +5V 400k T3 +5V 400k T4 19 2 3 1 24 5 R2IN + + +5V 400k 7 0.1F T1OUT T2OUT T3OUT T4OUT 4 R1IN 5k 22 23 R2IN R2OUT 5k R2 GND 15 11 V+ R1 R2OUT 0.1F VCC R1OUT 5k R1 10 C1+ + 12 C113 C2+ + 14 C2- 17 16 R3IN R3OUT 20 5k R3 21 SD EN GND 8 4 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN207E (SOIC, SSOP) TOP VIEW T3OUT T1OUT T2OUT 24 T3OUT 2 23 R3IN R2IN 3 22 R3OUT R2OUT 4 21 T4IN T1IN 5 20 T4OUT R1OUT 6 19 T3IN R1IN 7 18 T2IN GND 8 17 R4OUT VCC 9 16 R4IN 22 R2OUT 3 21 T5IN 20 T5OUT 5 19 T4IN T1IN 7 VCC 1 T1OUT 23 R2IN 2 T2IN 6 GND T2OUT 24 T4OUT 1 R1IN 4 R1OUT HIN208E (SOIC, SSOP) TOP VIEW 18 T3IN 17 R3OUT 8 16 R3IN 9 C1+ 10 15 V14 C2- V+ 11 13 C2+ C1- 12 15 V- C1+ 10 V+ 11 14 C2- C1- 12 13 C2+ +5V +5V 9 9 0.1F 0.1F T1IN T2IN T3IN T4IN T5IN 10 C1+ + 12 C113 C2+ + 14 C2- 11 +5V TO 10V VOLTAGE DOUBLER V+ +10V TO -10V VOLTAGE INVERTER V- 15 + T1 +5V 400k 6 T2 +5V 400k 18 T3 +5V 400k 19 T4 +5V 400k 21 T5 0.1F 0.1F + +5V 400k 7 0.1F VCC 2 3 1 24 0.1F T1OUT T2OUT T3OUT T4OUT T1IN T2IN T3IN T4IN 10 C1+ + 12 C113 C2+ + 14 C2- 0.1F VCC 11 +5V TO 10V VOLTAGE DOUBLER V+ +10V TO -10V VOLTAGE INVERTER V- 15 + +5V 400k 5 T1 +5V 400k T2 18 19 +5V 400k T3 +5V 400k T4 21 2 1 24 20 6 5 4 22 23 R2IN 17 22 R3IN 5k GND 5k 17 R3IN R3 23 R3OUT R3 16 R3OUT 16 R4IN R4OUT 5k R4 GND 8 5 R2IN 5k R2 T4OUT 5k R2 R2OUT T3OUT 3 R2OUT 5k R1 T2OUT R1IN T5OUT R1IN R1OUT T1OUT 5k R1 4 0.1F 7 R1OUT 20 + 8 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN211E (SOIC, SSOP) TOP VIEW HIN213E (SOIC, SSOP) TOP VIEW T3OUT 1 28 T4OUT T3OUT 1 28 T4OUT T1OUT 2 27 R3IN T1OUT 2 27 R3IN T2OUT 3 26 R3OUT T2OUT 3 26 R3OUT R2IN 4 25 SD R2IN 4 25 SD R2OUT 5 24 EN R2OUT 5 24 EN T2IN 6 23 R4IN T2IN 6 23 R4IN T1IN 7 22 R4OUT T1IN 7 22 R4OUT R1OUT 8 21 T4IN R1OUT 8 21 T4IN R1IN 9 20 T3IN R1IN 9 20 T3IN GND 10 19 R5OUT GND 10 19 R5OUT VCC 11 18 R5IN VCC 11 18 R5IN C1+ 12 17 V- C1+ 12 17 V- V+ 13 16 C2- V+ 13 16 C2- C1- 14 15 C2+ C1- 14 15 C2+ NOTE: R4 and R5 active in shutdown. +5V +5V 11 0.1F 0.1F T1IN T2IN T3IN T4IN R1OUT 12 C1+ + 14 C115 C2+ + 16 C2- 13 +5V TO 10V VOLTAGE DOUBLER V+ +10V TO -10V VOLTAGE INVERTER V- 17 + 0.1F 0.1F + +5V 400k 7 T1 +5V 400k T2 6 20 +5V 400k T3 21 +5V 400k T4 2 3 1 28 8 9 0.1F T1OUT T1IN T2OUT T2IN T3OUT T3IN T4OUT T4IN R1IN R1OUT 5 4 26 +5V 400k T2 6 20 +5V 400k T3 21 +5V 400k T4 R1IN 5k 4 R2IN 5k 27 R3IN 5k 23 R4IN 5k 19 18 R5IN R5OUT 5k 25 GND 9 R4 24 SD T4OUT R4OUT 18 R5 T3OUT 28 8 5k EN 1 22 R5IN T2OUT R3OUT 23 R5OUT T1OUT 3 26 R4IN 0.1F 2 R3 R4OUT 19 + T1 5k R4 V- 17 R2 R3IN 22 +10V TO -10V VOLTAGE INVERTER + R2OUT 27 R3 +5V TO 10V VOLTAGE DOUBLER +5V 400k 7 5k R3OUT 13 V+ 5 R2IN R2 0.1F VCC R1 R2OUT 5k R5 25 EN SD GND 10 6 12 C1+ + 14 C115 C2+ + 16 C2- 5k R1 24 11 0.1F VCC 10 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Pinouts (Continued) HIN232E (PDIP, SOIC, SSOP, TSSOP) TOP VIEW +5V 16 C1+ 1 16 VCC V+ 2 15 GND C1- 3 14 T1OUT C2+ 4 13 R1IN 0.1F 6 11 T1IN T2OUT 7 10 T2IN + 3 4 0.1F 12 R1OUT C2- 5 V- 1 T1IN + 5 C1+ C1C2+ C2- VCC +5V TO 10V VOLTAGE INVERTER V+ +10V TO -10V VOLTAGE INVERTER 2 + V- 6 + +5V 400k T1 11 +5V 400k T2 10 0.1F 0.1F 14 T1OUT 9 R2OUT R2IN 8 T2IN 7 12 T2OUT 13 R1IN R1OUT 5k R1 R2OUT 9 8 R2IN 5k R2 GND 15 Pin Descriptions PIN VCC FUNCTION Power Supply Input 5V 10%, (5V 5% HIN207E). V+ Internally generated positive supply (+10V nominal). V- Internally generated negative supply (-10V nominal). GND Ground Lead. Connect to 0V. C1+ External capacitor (+ terminal) is connected to this lead. C1- External capacitor (- terminal) is connected to this lead. C2+ External capacitor (+ terminal) is connected to this lead. C2- External capacitor (- terminal) is connected to this lead. TIN Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400k pull-up resistor to VCC is connected to each lead. TOUT RIN ROUT Transmitter Outputs. These are RS-232 levels (nominally 10V). Receiver Inputs. These inputs accept RS-232 input levels. An internal 5k pull-down resistor to GND is connected to each input. Receiver Outputs. These are TTL/CMOS levels. EN, EN Receiver Enable Input. With EN = 5V (HIN213E EN=0V), the receiver outputs are placed in a high impedance state. SD, SD Shutdown Input. With SD = 5V (HIN213E SD = 0V), the charge pump is disabled, the receiver outputs are in a high impedance state (except R4 and R5 of HIN213E) and the transmitters are shut off. NC No Connect. No connections are made to these leads. 7 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Absolute Maximum Ratings Thermal Information VCC to Ground. . . . . . . . . . . . . . . . . . . . . . (GND -0.3V) < VCC < 6V V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . (VCC -0.3V) < V+ < 12V V- to Ground . . . . . . . . . . . . . . . . . . . . . . .-12V < V- < (GND +0.3V) Input Voltages TIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V < VIN < (V+ +0.3V) RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V Output Voltages TOUT . . . . . . . . . . . . . . . . . . . .(V- -0.3V) < VTXOUT < (V+ +0.3V) ROUT . . . . . . . . . . . . . . . . . (GND -0.3V) < VRXOUT < (V+ +0.3V) Short Circuit Duration TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous ROUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous ESD Classification . . . . . . . . . . . . . . . . . . . . See Specification Table Thermal Resistance (Typical, Note 1) JA (C/W) 16 Ld SOIC (N) Package . . . . . . . . . . . . . . . . . . . . . 110 16 Ld SOIC (W) Package. . . . . . . . . . . . . . . . . . . . . 100 16 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . 155 16 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 145 16 Ld PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . 90 24 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 75 24 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . 135 28 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 70 28 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . 100 Maximum Junction Temperature (Plastic Package) . . . . . . . . 150C Maximum Storage Temperature Range . . . . . . . . . . -65C to 150C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300C (SOIC and SSOP - Lead Tips Only) Operating Conditions *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Temperature Range HIN2XXECX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C HIN2XXEIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40C to 85C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on an evaluation PC board in free air. Test Conditions: VCC = +5V 10%, (VCC = +5V 5% HIN207E); C1-C4 = 0.1F; TA = Operating Temperature Range Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS SUPPLY CURRENTS Power Supply Current, ICC No Load, TA = 25C Shutdown Supply Current, ICC(SD) TA = 25C HIN202E - 8 15 mA HIN206E - HIN208E, HIN211E, HIN213E - 11 20 mA HIN232E - 5 10 mA HIN206E, HIN211E - 1 10 A HIN213E - 15 50 A - - 0.8 V LOGIC AND TRANSMITTER INPUTS, RECEIVER OUTPUTS Input Logic Low, VlL TIN , EN, SD, EN, SD Input Logic High, VlH TIN 2.0 - - V EN, SD, EN, SD 2.4 - - V Transmitter Input Pullup Current, IP TIN = 0V - 15 200 A TTL/CMOS Receiver Output Voltage Low, VOL IOUT = 1.6mA (HIN202E, HIN232E, IOUT = 3.2mA) - 0.1 0.4 V TTL/CMOS Receiver Output Voltage High, VOH IOUT = -1mA 3.5 4.6 - V TTL/CMOS Receiver Output Leakage EN = VCC , EN = 0, 0V < ROUT < VCC - 0.5 10 A -30 - +30 V 3.0 5.0 7.0 k RECEIVER INPUTS RS-232 Input Voltage Range, VIN Receiver Input Impedance, RIN TA = 25C, VIN = 3V Receiver Input Low Threshold, VIN (H-L) VCC = 5V, TA = 25C Active Mode - 1.2 - V Shutdown Mode HIN213E R4 and R5 - 1.5 - V VCC = 5V, TA = 25C Active Mode - 1.7 2.4 V Shutdown Mode HIN213E R4 and R5 - 1.5 2.4 V 0.2 0.5 1.0 V Receiver Input High Threshold, VIN (L-H) Receiver Input Hysteresis, VHYST 8 VCC = 5V, No Hysteresis in Shutdown Mode FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Test Conditions: VCC = +5V 10%, (VCC = +5V 5% HIN207E); C1-C4 = 0.1F; TA = Operating Temperature Range (Continued) Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS TIMING CHARACTERISTICS Output Enable Time, tEN HIN206E, HIN211E, HIN213E - 600 - ns Output Disable Time, tDIS HIN206E, HIN211E, HIN213E - 200 - ns Transmitter, Receiver Propagation Delay, tPD HIN213E SD = 0V, R4, R5 - 4.0 40 s HIN213E SD = VCC , R1 - R5 - 0.5 10 s All except HIN213E - 0.5 10 s RL = 3k, CL = 1000pF Measured from +3V to -3V or -3V to +3V, 1 Transmitter Switching (Note 2) 3 20 45 V/s Output Voltage Swing, TOUT Transmitter Outputs, 3k to Ground 5 9 10 V Output Resistance, TOUT VCC = V+ = V- = 0V, VOUT = 2V 300 - - RS-232 Output Short Circuit Current, ISC TOUT Shorted to GND - 10 - mA Human Body Model - 15 - kV Transition Region Slew Rate, SRT TRANSMITTER OUTPUTS ESD PERFORMANCE RS-232 Pins (TOUT, RIN) All Other Pins IEC61000-4-2 Contact Discharge - 8 - kV IEC61000-4-2 Air Gap (Note 3) - 15 - kV Human Body Model - 2 - kV NOTES: 2. Guaranteed by design. 3. Meets Level 4. Test Circuits (HIN232E) +4.5V TO +5.5V INPUT 0.1F C3 0.1F C1 1 C1+ - 2 V+ + 3 C1- + - 0.1F + C2 - - + 0.1F C4 3k 1 C1+ VCC 16 2 V+ GND 15 T1OUT 14 4 C2+ R1IN 13 RS-232 30V INPUT 5 C2- R1OUT 12 TTL/CMOS OUTPUT 6 V7 T2OUT 8 R2IN T1 OUTPUT T1IN 11 TTL/CMOS INPUT T2IN 10 TTL/CMOS INPUT R2OUT 9 TTL/CMOS OUTPUT T2 OUTPUT GND 15 T1OUT 14 4 C2+ R1IN 13 5 C2- R1OUT 12 3k 3 C1- VCC 16 6 V- T1IN 11 7 T2OUT T2IN 10 8 R2IN ROUT = VIN /I R2OUT 9 T2OUT T1OUT VIN = 2V A RS-232 30V INPUT FIGURE 1. GENERAL TEST CIRCUIT 9 FIGURE 2. POWER-OFF SOURCE RESISTANCE CONFIGURATION FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E VOLTAGE DOUBLER S1 VOLTAGE INVERTER S2 C1+ V+ = 2VCC S5 C2+ S6 VCC GND + GND S3 C1- + C1 - + C3 VCC S4 + C2 - C4 GND C2- S7 V- = - (V+) S8 RC OSCILLATOR FIGURE 3. CHARGE PUMP Detailed Description The HIN2XXE family of high-speed RS-232 transmitters/receivers are powered by a single +5V power supply, feature low power consumption, and meet all ElA RS232C and V.28 specifications. The circuit is divided into three sections: the charge pump, transmitter, and receiver. Charge Pump An equivalent circuit of the charge pump is illustrated in Figure 3. The charge pump contains two sections: the voltage doubler and the voltage inverter. Each section is driven by a two phase, internally generated clock to generate +10V and -10V. The nominal clock frequency is 125kHz. During phase one of the clock, capacitor C1 is charged to VCC . During phase two, the voltage on C1 is added to VCC , producing a signal across C3 equal to twice VCC . During phase two, C2 is also charged to 2VCC , and then during phase one, it is inverted with respect to ground to produce a signal across C4 equal to -2VCC . The charge pump accepts input voltages up to 5.5V. The output impedance of the voltage doubler section (V+) is approximately 200, and the output impedance of the voltage inverter section (V-) is approximately 450. A typical application uses 0.1F capacitors for C1-C4, however, the value is not critical. Increasing the values of C1 and C2 will lower the output impedance of the voltage doubler and inverter, increasing the values of the reservoir capacitors, C3 and C4, lowers the ripple on the V+ and V- supplies. During shutdown mode (HIN206E, HIN211E and HIN213E) the charge pump is turned off, V+ is pulled down to VCC , Vis pulled up to GND, and the supply current is reduced to less than 10A. The transmitter outputs are disabled and the receiver outputs (except for HIN213E, R4 and R5) are placed in the high impedance state. and (V+ -0.6V). Each transmitter input has an internal 400k pullup resistor so any unused input can be left unconnected and its output remains in its low state. The output voltage swing meets the RS-232C specifications of 5V minimum with the worst case conditions of: all transmitters driving 3k minimum load impedance, VCC = 4.5V, and maximum allowable operating temperature. The transmitters have an internally limited output slew rate which is less than 30V/s. The outputs are short circuit protected and can be shorted to ground indefinitely. The powered down output impedance is a minimum of 300 with 2V applied to the outputs and VCC = 0V. Receivers The receiver inputs accept up to 30V while presenting the required 3k to 7k input impedance even if the power is off (VCC = 0V). The receivers have a typical input threshold of 1.3V which is within the 3V limits, known as the transition region, of the RS-232 specifications. The receiver output is 0V to VCC . The output will be low whenever the input is greater than 2.4V and high whenever the input is floating or driven between +0.8V and -30V. The receivers feature 0.5V hysteresis (except during shutdown) to improve noise rejection. The receiver Enable line EN, (EN on HIN213E) when unasserted, disables the receiver outputs, placing them in the high impedance mode. The receiver outputs are also placed in the high impedance state when in shutdown mode (except HIN213E R4 and R5). V+ VCC 400k 300 TXIN TOUT GND < TXIN < VCC V- < VTOUT < V+ V- Transmitters The transmitters are TTL/CMOS compatible inverters which translate the inputs to RS-232 outputs. The input logic threshold is about 26% of VCC , or 1.3V for VCC = 5V. A logic 1 at the input results in a voltage of between -5V and V- at the output, and a logic 0 results in a voltage between +5V 10 FIGURE 4. TRANSMITTER FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Application Information VCC RXIN ROUT -30V < RXIN < +30V GND < VROUT < VCC 5k GND FIGURE 5. RECEIVER A simple duplex RS-232 port with CTS/RTS handshaking is illustrated in Figure 7. Fixed output signals such as DTR (data terminal ready) and DSRS (data signaling rate select) is generated by driving them through a 5k resistor connected to V+. TIN OR RIN TOUT OR ROUT VOL VOL tPHL tPLH AVERAGE PROPAGATION DELAY = The HIN2XXE may be used for all RS-232 data terminal and communication links. It is particularly useful in applications where 12V power supplies are not available for conventional RS-232 interface circuits. The applications presented represent typical interface configurations. tPHL + tPLH 2 In applications requiring four RS-232 inputs and outputs (Figure 8), note that each circuit requires two charge pump capacitors (C1 and C2) but can share common reservoir capacitors (C3 and C4). The benefit of sharing common reservoir capacitors is the elimination of two capacitors and the reduction of the charge pump source impedance which effectively increases the output swing of the transmitters. FIGURE 6. PROPAGATION DELAY DEFINITION +5V - HIN213E Operation in Shutdown The HIN213E features two receivers, R4 and R5, which remain active in shutdown mode. During normal operation the receivers propagation delay is typically 0.5s. This propagation delay may increase slightly during shutdown. When entering shut down mode, receivers R4 and R5 are not valid for 80s after SD = VIL. When exiting shutdown mode, all receiver outputs will be invalid until the charge pump circuitry reaches normal operating voltage. This is typically less than 2ms when using 0.1F capacitors. 1 C1 + 0.1F - + 16 3 HIN232E 6 4 C2 + 0.1F TD INPUTS OUTPUTS TTL/CMOS RTS 5 T1 11 14 T2 10 7 13 12 RD CTS 9 + R2 R1 15 8 CTR (20) DATA TERMINAL READY DSRS (24) DATA SIGNALING RATE SELECT RS-232 INPUTS AND OUTPUTS TD (2) TRANSMIT DATA RTS (4) REQUEST TO SEND RD (3) RECEIVE DATA CTS (5) CLEAR TO SEND SIGNAL GROUND (7) FIGURE 7. SIMPLE DUPLEX RS-232 PORT WITH CTS/RTS HANDSHAKING 11 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E 1 C1 + 0.1F TD INPUTS OUTPUTS TTL/CMOS RTS 4 HIN232E 3 T1 11 - 14 T2 10 + C2 0.1F 5 TD (2) TRANSMIT DATA 7 RTS (4) REQUEST TO SEND 13 12 RD (3) RECEIVE DATA RD R2 9 CTS R1 8 CTS (5) CLEAR TO SEND 15 VCC 16 - 2 C3 + + C4 6 V- V+ 0.2F 6 +5V - RS-232 INPUTS AND OUTPUTS 0.2F 2 VCC 16 HIN232E C1 + 0.1F DTR INPUTS OUTPUTS TTL/CMOS DSRS 1 4 3 5 T1 11 14 T2 10 12 7 13 DCD R1 9 R2 R1 15 8 + C2 0.1F - DTR (20) DATA TERMINAL READY DSRS (24) DATA SIGNALING RATE SELECT DCD (8) DATA CARRIER DETECT R1 (22) RING INDICATOR SIGNAL GROUND (7) FIGURE 8. COMBINING TWO HIN232Es FOR 4 PAIRS OF RS-232 INPUTS AND OUTPUTS Typical Performance Curves 12 0.1F SUPPLY VOLTAGE (|V|) V- SUPPLY VOLTAGE (V) 12 10 8 6 4 V+ (VCC = 5V) 8 6 V+ (VCC = 4V) V- (VCC = 4V) 4 TA = 25C TRANSMITTER OUTPUTS OPEN CIRCUIT 2 2 0 3.0 10 3.5 FIGURE 9. 4.0 4.5 VCC 5.0 5.5 V- SUPPLY VOLTAGE vs VCC 12 6.0 0 0 5 10 15 V- (VCC = 5V) 20 25 30 35 |ILOAD| (mA) FIGURE 10. V+, V- OUTPUT VOLTAGE vs LOAD FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Die Characteristics METALLIZATION: PASSIVATION: Type: Nitride over Silox Nitride Thickness: 8kA Silox Thickness: 7kA Type: Al Thickness: 10kA 1kA SUBSTRATE POTENTIAL TRANSISTOR COUNT: GND 185 PROCESS: CMOS Metal Gate Metallization Mask Layout HIN232E VPIN 6 C2PIN 5 C2+ PIN 4 C1PIN 3 PIN 2 V+ PIN 1 C1+ T2OUT PIN 7 R2IN PIN 8 T3OUT PIN 9 PIN 17 VCC R2OUT PIN 10 PIN 11 T2IN PIN 12 T1IN 13 PIN 13 R1OUT PIN 14 R1IN PIN 15 T1OUT PIN 16 GND FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Dual-In-Line Plastic Packages (PDIP) E16.3 (JEDEC MS-001-BB ISSUE D) N 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AE D BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8, 10 eA C 0.008 0.014 C D 0.735 0.775 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 0.355 19.68 5 D1 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. eA 0.300 BSC 3. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication No. 95. eB - 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. L 0.115 N 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 0.204 18.66 16 2.54 BSC - 7.62 BSC 0.430 - 0.150 2.93 16 6 10.92 7 3.81 4 9 Rev. 0 12/93 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 14 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) N INDEX AREA H 0.25(0.010) M 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M INCHES E -B- 1 2 3 L SEATING PLANE -A- A D h x 45 -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e B S 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS 16 0 16 8 0 7 8 Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 15 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Thin Shrink Small Outline Plastic Packages (TSSOP) M16.173 N 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE INDEX AREA E 0.25(0.010) M 2 INCHES E1 GAUGE PLANE -B1 B M L 0.05(0.002) -A- SYMBOL MIN MAX MIN MAX NOTES A - 0.043 - 1.10 - A1 3 A D -C- e c 0.10(0.004) C A M 0.05 0.15 - A2 0.033 0.037 0.85 0.95 - b 0.0075 0.012 0.19 0.30 9 c 0.0035 0.008 0.09 0.20 - B S 0.002 D 0.193 0.201 4.90 5.10 3 0.169 0.177 4.30 4.50 4 0.026 BSC E 0.246 L 0.020 N NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. 0.006 E1 e A2 A1 b 0.10(0.004) M 0.25 0.010 SEATING PLANE MILLIMETERS 0.65 BSC 0.256 6.25 0.028 0.50 16 0o - 0.70 6 16 8o 0o - 6.50 7 8o Rev. 1 2/02 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E1" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of "b" dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) 16 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SSOP) M16.209 (JEDEC MO-150-AC ISSUE B) N INDEX AREA 16 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M 2 GAUGE PLANE 3 0.25 0.010 SEATING PLANE -A- INCHES E -B- 1 B M A D -C- e C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - A1 0.002 - 0.05 - - A2 0.065 0.072 1.65 1.85 - B 0.009 0.014 0.22 0.38 9 C 0.004 0.009 0.09 0.25 - D 0.233 0.255 5.90 6.50 3 E 0.197 0.220 5.00 5.60 4 e A2 A1 B 0.25(0.010) M L B S 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 0.026 BSC H 0.292 L 0.022 N NOTES: MILLIMETERS 0.65 BSC 0.322 7.40 0.037 0.55 16 0 - 8.20 - 0.95 6 16 8 0 7 8 Rev. 3 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.20mm (0.0078 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "B" does not include dambar protrusion. Allowable dambar protrusion shall be 0.13mm (0.005 inch) total in excess of "B" dimension at maximum material condition. 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 17 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M16.3 (JEDEC MS-013-AA ISSUE C) N INDEX AREA 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M B M INCHES E -B- 1 2 3 L SEATING PLANE -A- A D h x 45 -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.3977 0.4133 10.10 10.50 3 E 0.2914 0.2992 7.40 7.60 4 e B S 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 0.050 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS 16 0 16 8 0 7 8 Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 18 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Shrink Small Outline Plastic Packages (SSOP) M24.209 (JEDEC MO-150-AG ISSUE B) N 24 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E GAUGE PLANE -B1 2 3 L 0.25 0.010 SEATING PLANE -A- A D -C- e B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - 0.05 - - 0.072 1.65 1.85 - A1 0.002 A2 0.065 B S B 0.009 0.014 0.22 0.38 9 0.004 0.009 0.09 0.25 - D 0.312 0.334 7.90 8.50 3 E 0.197 0.220 5.00 5.60 4 0.026 BSC H 0.292 L 0.022 N NOTES: - C e A2 A1 MILLIMETERS 0.65 BSC 0.322 7.40 0.037 0.55 24 0o - 8.20 - 0.95 6 24 8o 0o 7 8o Rev. 1 3/95 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.20mm (0.0078 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "B" does not include dambar protrusion. Allowable dambar protrusion shall be 0.13mm (0.005 inch) total in excess of "B" dimension at maximum material condition. 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 19 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M24.3 (JEDEC MS-013-AD ISSUE C) N 24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E -B1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.020 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.5985 0.6141 15.20 15.60 3 E 0.2914 0.2992 7.40 7.60 4 e B S 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 0.05 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 N NOTES: MILLIMETERS 24 0o 24 8o 0o 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 20 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Shrink Small Outline Plastic Packages (SSOP) M28.209 (JEDEC MO-150-AH ISSUE B) N INDEX AREA 28 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M 2 GAUGE PLANE 3 0.25 0.010 SEATING PLANE -A- INCHES E -B- 1 B M A D -C- e C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A - 0.078 - 2.00 - A1 0.002 - 0.05 - - A2 0.065 0.072 1.65 1.85 - B 0.009 0.014 0.22 0.38 9 C 0.004 0.009 0.09 0.25 - D 0.390 0.413 9.90 10.50 3 E 0.197 0.220 5.00 5.60 4 e A2 A1 B 0.25(0.010) M L B S NOTES: 0.026 BSC H 0.292 L 0.022 N 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. MILLIMETERS 0.65 BSC 0.322 7.40 0.037 0.55 28 0 - 0.95 6 28 8 0 - 8.20 7 8 Rev. 2 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.20mm (0.0078 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "B" does not include dambar protrusion. Allowable dambar protrusion shall be 0.13mm (0.005 inch) total in excess of "B" dimension at maximum material condition. 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 21 FN4315.16 November 4, 2005 HIN202E, HIN206E, HIN207E, HIN208E, HIN211E, HIN213E, HIN232E Small Outline Plastic Packages (SOIC) M28.3 (JEDEC MS-013-AE ISSUE C) N 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B C 0.10(0.004) 0.25(0.010) M C A M B S MILLIMETERS MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.6969 0.7125 17.70 18.10 3 E 0.2914 0.2992 7.40 7.60 4 0.05 BSC 10.00 - 0.394 h 0.01 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 8o 0o N 0.419 1.27 BSC H NOTES: MAX A1 e MIN 28 0o 10.65 28 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. - 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 22 FN4315.16 November 4, 2005