DP1203C9153LF - Semtech - Datasheet.Directory

Rev 3 May 2006 www.semtech.com

1

DP1203F

433/868/915 MHz RF Modules

DP1203F – C433 / 868 / 915

433, 868 and 915 MHz Drop-In RF Transceiver Modules

Combine Small Form Factor with High Performance

GENERAL DESCRIPTI ON

The DP1203Fs are complete Radio Transceiver

Modules operating in the 433, 868 and 915 MHz

license free ISM (Industrial Scientific and Medical)

frequency bands. Based on the XE1203F

transceiver, the DP1203F offers the unique

advantage of high data rate communication up to

152.3 kbit/s. Combining high output power and

exceptional receiver sensitivity, the radio modules is

suitable for applications seeking to satisfy the

European (ETSI EN300-220-1 and EN301 439-3) or

the North American (FCC part 15.247 and 15.249)

regulatory standards.

The DP1203F modules can be used in any

environment where wireless remote connection is an

advantage. The DP1203F modules are perfect for

complex wireless networks involving high speed data

rate applications.

APPLICATIONS

• Home automation and access control

• Wireless Network

• Process and building control

KEY PRODUCT FEATURES

• No RF knowledge required

• Direct Digital interface

• Fully assembled and tested

• Surface mount

• 30.5 mm x 18.5 mm

• Available on tape&reel for Automatic assembly

system

• Supply voltage 2.4 V – 3.6 V

• Frequency synthesizer steps 500 Hz

• Output power is programmable up to 15 dBm

• High Rx 0.1% sensitivity down to -111 dBm

• Data rate up to 152.3 kbit/s

• Current consumption Tx=62 mA at15 dBm

• Current consumption Rx=14 mA

• Digital RSSI (Received Signal Strength Indicator)

• Digital FEI (Frequency Error Indicator)

DEVICE OPTIO NS

Part Number Frequency band Package

DP1203C4333LF 433-435 MHz Board

DP1203C8683LF 868-870 MHz Board

DP1203C9153LF 902-928 MHz Board

2

DP1203F

433/868/915 MHz RF Modules

Table of Contents

1 Pin Description............................................................................................................................................3

2 Electrical Characteristics ...........................................................................................................................4

2.1 Absolute maximum operating ranges............................................................................................................4

2.2 Specifications ................................................................................................................................................5

3 Functional Description ...............................................................................................................................6

4 Serial Control Interface...............................................................................................................................7

5 Operation Modes.........................................................................................................................................8

5.1 Standard sequence for switching between receiver and transmitter ............................................................9

6 Typical Application ...................................................................................................................................10

7 Mechanical Dimensions............................................................................................................................11

8 Packaging Information..............................................................................................................................12

9 References.................................................................................................................................................12

3

DP1203F

433/868/915 MHz RF Modules

1 PIN DESCRIPTION

XE1203F

1

2

3

30.5

18.50

Pad Dimension

1.8

45 6

678910

11

12

13141516

1718192021

1.0

PIN NAME I/O DESCRIPTION

1 GND IN Ground

2 RFIN/OUT IN/OUT RF input / output terminal

3 GND Ground

4 VDDP Supply voltage / Advised NC

5 VDDA Supply voltage

6 GND Ground

7 VDD Supply voltage

8 EN IN 3-wire interface communication enable signal

9 SWITCH IN/OUT Operating mode selection

10 GND Ground

11 GND Ground

12 SO OUT Data output of the 3-wires interface

13 SI IN Data input of the 3-wires interface

14 SCK IN Input clock of the 3-wires interface

15 CLKOUT OUT Output clock at quartz frequency divided by 4, 8, 16 or 32

16 DCLK OUT Transmitter or Receiver clock

17 DATA IN/OUT Transmitter input data or Receiver output data

18 DATAIN IN Transmitter input data

19 PATTERN OUT Output of the pattern recognition block

20 RX IN Antenna switch RX Select

21 TX IN Antenna switch TX select

4

DP1203F

433/868/915 MHz RF Modules

2 ELECTRICAL CHARACTERISTICS

2.1 ABSOLUTE MAXIMUM OPERATING RANGES

Description Min Max Unit

Supply voltage 2.4 3.6 V

Operating temperature -40 +85 oC

Storage temperature -55 125 oC

Soldering temperature (max 15 sec) 260 oC

CAUTION: ESD sensitive device.

Precaution should be taken when handling the device in order to prevent permanent damage

Life Support Policy and Use in Safety Critical Application s

SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE

FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS.

INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN

SOLELY AT THE CUSTOMER’S OWN RISK.

5

DP1203F

433/868/915 MHz RF Modules

2.2 SPECIFICATIONS

The table below gives the specifications of the DP1203F under the following conditions:

Supply Voltage VDD = 3.3V, temperature = 25°C, 2-level FSK without pre-filtering, carrier frequency fc = 434 MHz

for DP1203C4333LF, fc = 869 MHz for DP1203C8683LF and fc = 915 MHz for DP1203C9153LF, frequency

deviation ∆f = 55 kHz, bit rate BR = 4.8kbps, Base band filter bandwidth BBW = 200 KHz, bit error rate BER = 0.1

% (measured at the output of the bit synchronizer), antenna output matched at 50 Ω.

Symbol Parameter Conditions Min Typ Max Units

FR Synthesizer Frequency Range DP1203C4333LF 433 - 435 MHz

DP1203C8683LF 868 - 870 MHz

DP1203C9153LF 902 - 928 MHz

IDDSL Sleep mode supply current 0.2 1 uA

IDDST Standby mode supply current 39 MHz running 0.85 1.1 mA

IDDR RX mode supply current 14 17 mA

IDDT TX mode supply current PRF = 5 dBm 33 40 mA

P

RF = 15dBm 62 75 mA

RFS RF Sensitivity A-mode, BR = 4.8 kbps /

BER = 0.1%

-111 -108 dBm

FDA Frequency Deviation Programmable 1 - 255 kHz

BR Bit rate Programmable 1.2 - 152.3 Kb/s

PRF RF output power Programmable.

RFOP1 -3 0 - dBm

RFOP2 +2 +5 - dBm

RFOP3 +7 +10 - dBm

RFOP4 +12 +15 - dBm

TS_TR Transmitter wake-up time From oscillator enabled - 150 250 us

TS_RE Receiver base-band wake up time From oscillator enabled - 0.5 0.8 ms

TS_OS Quartz oscillator wake up time Fundamental - 1 2 ms

XTAL Quartz oscillator frequency 39 MHz

VIH Digital input level high % VDD 75 - - %

VIL Digital input level low % VDD - - 25 %

6

DP1203F

433/868/915 MHz RF Modules

3 FUNCTIONAL DESCRI PTI O N

The True RF DP1203F is a cost effective high performance radio transceiver module designed for the wireless

transmission of digital information over distances of >500 meters in free space.

The module is based on the RF transceiver circuit from SEMTECH, the XE1203F. For more information on the

XE1203F, please refer to the XE1203F datasheet.

The module incorporates an antenna switch and a SAW Filter placed on the Rx path.

DCLKDATA

RXTX

XE1203F

VCO

tank

Loop

filter

Xtal

39 MHz

LNA matchSAW

PA match

RF

Switch

CLKOUT SCK SI SO GND

GNDSWITCH

ENVDD

GNDVDDA

GND

RF IN/

OUT

GND

VDDP

DATAINPATTERN

7

DP1203F

433/868/915 MHz RF Modules

4 SERIAL CONTROL INTERFACE

A 3-wire bi-directional bus (SCK, SI, SO) is used to control the DP1203F. The output signal, SO, is provided by the

DP1203F in opposition to the SCK and SI which needs to be provided by the external application as an 8-bit

microcontroller. An access Read or Write with the XE1203F is possible only when the enable signal is active

(active LOW).

For more information about the 3-wire bus, please refer to the XE1203F datasheet chapter; Serial interface

definitio n a nd principles of operat io n.

Write sequence into configuration register

Read sequence of configuration register

A

(4)

A

(3)

A

(2)

A

(1)

A

(0)

D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0)

sck

si

/en

so High impedance High impedance

A

(4)

A

(3)

A

(2)

A

(1)

A

(0) D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0)

sck

si

/en

so High impedance

8

DP1203F

433/868/915 MHz RF Modules

5 OPERATION MODES

When operating the XE1203F, it might by useful to quickly switch between two pre-defined operating modes, to

save time and traffic on the 3-wire serial interface bus. This may occur when the XE1203F is required to switch

quickly between receive and transmit mode, when it has to operate on two different carrier frequencies, or when it

has to switch between the high linearity mode B and the high sensitivity mode A. For that purpose, the five

parameters stored in the SWParam Configuration Register are duplicated: the configuration set#1 and the

configuration set #2.

Depending on the ConfigSwitch 1-bit Register or the input level at the SWITCH pin, the XE1203F transceiver will

use either the SWParam configuration set#1 or the set #2. If the RTParam_Switch_ext configuration parameter is

low, then the SWParam configuration set is selected by the ConfigSwitch parameter – set#1 if ConfigSwitch is “0”,

set#2 if ConfigSwitch is “1”. If the RTParam_Switch_ext configuration parameter is high, then the SWParam

configuration set is selected by the SWITCH pin – set#1 if SWITCH is low, set#2 if SWITCH is high.

ConfigSwitch

Register SWITCH pin RTParam_switch_ext

configuration parameter SWParam configuration

set selected

0 SWITCH is an output:

‘1’ in transmitter mode

‘0’ in the other modes

0 Set #1:

SWParam_mode_1

SWParam_Power_1

SWParam_Rmode_1

SWParam_t_delsig_in_1

SWParam_freq_1

1 SWITCH is an output:

‘1’ in transmitter mode

‘0’ in the other modes

0 Set #2:

SWParam_mode_2

SWParam_Power_2

SWParam_Rmode_2

SWParam_t_delsig_in_2

SWParam_freq_2

X 0 1 Set #1:

SWParam_mode_1

SWParam_Power_1

SWParam_Rmode_1

SWParam_t_delsig_in_1

SWParam_freq_1

X 1 1 Set #2:

SWParam_mode_2

SWParam_Power_2

SWParam_Rmode_2

SWParam_t_delsig_in_2

SWParam_freq_2

ConfigSwitch, SWITCH pin and SWParam Configuration Register

For more information about the modes of operation, please refer to the XE1203F Datasheet.

9

DP1203F

433/868/915 MHz RF Modules

5.1 STANDARD SEQUENC E FOR SWI T CHING BETWEEN RECEI VER AND TRANSMITTER

The drop-in module DP1203F is able to switch between any configuration by using the 3-wire bus or by using the

pin SWITCH. This section describes the switching sequence from Set #1 to Set #2.

Switching sequence by using the 3-wire bus

RTParam_switch_ext = 0

Switching sequence by pad SWITCH

RTParam_switch_ext = 1

10

DP1203F

433/868/915 MHz RF Modules

6 TYPICAL APPLICATION

The schematic below shows the DP1203F interfaced with a SEMTECH’s microcontroller XE8806A.

PD1

PD2

PD3

PD4

PD6

PD7

PD5

PD0

PB4

PB5

BIT

JOCKEY

XE8806A

XE1203F

VCO

tank

Loop

filter

Xtal

39 MHz

LNA matchSAW

PA match

RF

Switch

PB6

DCLKDATA

RXTX CLKOUT SCK SI SO GND

DATAINPATTERN

GNDSWITCH

ENVDD

GNDVDDAVDDP

GND

RF IN/OUT

GND

VCC

1nF

82 nH

Ω0

33 pF

100 pF

11

DP1203F

433/868/915 MHz RF Modules

7 MECHANICAL DIMENSIONS

The following diagram shows the physical footprint and dimensions of the DP1203F drop-in module, which should

be implemented on the mother board.

XE1203F

1

2

3

3.27 2.54 2.54 2.54 2.54 2.54 2.54 2.54

2.54 5.08 2.54 2.54 2.54 2.54

30.5

10.89

1.83

2.54

1.83

18.50

2.50

2.54 2.54 10.92

Pad Dimension Footprint

adviced

1.8 2.0

45 6

678910

11

12

13141516

1718192021

2.542.54

1.0 1.2

Top view Bottom view

12

DP1203F

433/868/915 MHz RF Modules

8 PACKAGING INFORMATION

9 REFERENCES

- The XE1203F and the XE8806A datasheets, as well as the TN8000.18 Technical Note (XE8000 driving

XE1200 transceivers standard API definitions) are available from Semtech website (www.semtech.com).

13

DP1203F

433/868/915 MHz RF Modules

.

Contact Information

information presented in this document does not form part of any quotation or contract, is believed to be accurate and

reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.

Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

Semtech. assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse,

neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to,

exposure to parameters beyond the specified maximum ratings or operation outside the specified range.

SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR

USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION

OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE

CUSTOMER’S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application,

the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless

against all claims, costs damages and attorney fees which could arise.

Semtech Corporation

Wireless and Sensing Products Division

200 Flynn Road, Camarillo, CA 93012

Phone (805) 498-2111 Fax : (805) 498-3804