Bi-Directional Control Thyristor Product Information ABB Semiconductors AG Bi-Directional Control Thyristor Product Information Bjorn Backlund, Jan-Olav Boeriis, Ken Thomas, Robert Waishar, Jurg Waldmeyer, Orhan Toker ABB Semiconductors AG February 1999. 1. Introduction The Bi-Directional Control Thyristor (BCT) is a new concept for high power phase control thyristors (PCTs) developed by ABB Semiconductors. Two anti-parallel high power thyristors are integrated onto one single silicon wafer and are assembled into one housing. This new feature will enable designers of static VAr compensators, static switches, soft starters and motor drives to meet higher demands concerning size, integration, reliability and cost for their end product. ABB Semiconductors has developed this concept utilising 4" and 5" silicon technology aiming for a product matrix of 73, 84, 96 and 118 mm wafers and voltages from 1800 V to 6500 V. The range of 4" devices (96 mm wafer) was released for production in 1998 and the 3" (73 mm wafer), the 3.5" (84 mm wafer) and the 5" devices (118 mm wafer) are planned for release in 1999. The product range and the corresponding short form data are presented in section 2. 2 The basic product philosophy is the same as for the Phase Control Thyristors (PCTs). Standard devices are described in data sheets, and our flexibility in the irradiation and testing process gives opportunities for adapted standard devices. The wafer design, the mechanical design, the manufacturing and the testing of the Bi-Directional Control Thyristors (BCTs) are based on the same technology and philosophy as for the well proven PCTs. In combination with the extensive qualification of newly developed devices this assures that the same high quality and reliability is achieved. The Bi-Directional Control Thyristor (BCT) family is a strong complement to ABB Semiconductors' present PCT family, and our increased resources in application, customer technology, rating and evaluation assures that we continue to support our customers' demands with an even more competitive product range. Doc. No. 5SYA 2006-02 Feb. 99 2. BCT Product Matrix and Short Form Data The matrix below gives an overview of the planned devices in the BCT family. All the data given below represents one "thyristor-half" of the device. Housing type VRM ITAVM ITSM VTO rt Tvjm RthJC RthCH V V Tc=70C A 10ms Tvjm kA Tvjm V Tvjm m C K/kW K/kW 5STB 16H2800 5STB 18H1800 2800 1800 2800 1800 1580 1845 18.0 21.0 0.82 0.83 0.37 0.23 125 125 16 16 10 10 H H 5STB 09M6500 6500 5600 940 14.0 1.25 0.86 125 18 6 M 5STB 13N6500 5STB 17N5200 5STB 18N4200 5STB 24N2800 5STB 27N1800 6500 5200 4200 2800 1800 5600 4400 4200 2800 1800 1390 1700 1850 2350 3000 22.0 29.0 32.0 43.0 47.0 1.20 1.02 0.96 0.85 0.88 0.60 0.32 0.28 0.16 0.103 125 125 125 125 125 12 12 12 12 12 5 5 5 5 5 N N N N N 5STB 18U6500 5STB 25U5200 6500 5200 5600 4400 1800 2500 32.0 42.0 1.20 1.00 0.43 0.22 125 125 8 8 3 3 U U Type and ordering number VSM The devices in the N housing (96 mm wafer) except 5STB 27N1800 are available in production quantities in 1998. The device in the H housing (73 mm wafer), M housing (84 mm wafer) and the 5STB 27N1800 will be available upon request. The devices in the U-type housing (118 mm wafer) are available in sample quantities in 1999 and in production quantities in 2000. Final data sheets are released for the devices in Nhousing and tentative data sheet are available for the other types. Final data sheets for those will be released as soon as the devices are approved and released for production. N-housing H-housing M-housing Fig. 2.1: Housing outline of the different BCT products. 3 U-housing Doc. No. 5SYA 2006-02 Feb. 99 3. BCT Design The BCT is a unique device, bringing the customer the advantages of having two thyristors in one package: enabling more compact equipment design, simplifying the cooling system and increasing system reliability. The success of the BCT technology is based on its compatibility in process and design with ABB's well established PCT range. Reliability is guaranteed by our well proven negative bevel junction termination and free floating silicon technologies. 3.1 BCT Design Criteria 1. The electrical behaviour of a BCT corresponds to that of two anti-parallel thyristors (e.g. of 2 approximately 27 cm area each for the 96mm wafer diameter) integrated onto one silicon slice, (figure 3.1). Each thyristor-half performs like the corresponding full-wafer thyristor in respect to its static and dynamic properties. Fig. 3.1: Schematic cross-section of a BCT wafer showing A and B thyristor-halves and defining the two forward voltage directions VA(t) and VB(t). Later in the text these voltages will be labelled VD(A)(t) and VD(B)(t) for better clarity about forward and reverse directions. 2. A major challenge in the integration of the two thyristor-halves is crosstalk between the two halves. The photomask set has been designed with a high focus on avoiding harmful crosstalk effects under all relevant operating conditions. 3. Electrical performance shows very high uniformity between the two halves in device parameters such 4 as reverse recovery charge and on-state voltage. This is demonstrated in figures 3.2 and 3.3. Figure 3.2 compares the spread in (Q) for the A thyristorhalves against the spread for the B thyristor-halves for 33 devices tuned by electron irradiation to have a fixed on-state voltage. Figure 3.3 shows leakage current distributions at 4400 V and 110C. Doc. No. 5SYA 2006-02 Feb. 99 12 10 Number of events Thyristor half A 8 Thyristor half B 6 4 2 0 3000 3100 3200 3300 3400 Q [As] 3500 3600 3700 Fig. 3.2: Histogram of the reverse recovery charge distribution of the A and the B thyristor-halves in a sample of 33 BCT devices. 4 Number of events A is forward blocking 3 B is forward blocking 2 1 0 0 10 20 Leakage current [mA] 30 40 Fig. 3.3: Histogram of the leakage current at 4400 V and 110 C for the A and the B thyristor-halves blocking in forward direction. Sample of 8 BCT devices. 5 Doc. No. 5SYA 2006-02 Feb. 99 housing dimensions are given in the BCT product matrix (figure 2.1). 3.2 Special BCT Features 1. Under off-state blocking conditions no unique reverse direction exists, both voltage polarities correspond to forward blocking states of the A thyristor-half or the B thyristor-half respectively. This has an effect on the specification and on the parameter terminology. There is therefore no extra reverse blocking requirement as in a standard Phase Controlled Thyristor (PCT). 2. The BCT wafer has anode and cathode regions on each face. The A and B thyristors are identified on the wafer by letters A, B on the central gate metallisation, (figure 3.1). 3. The BCT housings have been designed to correspond in size to our standard PCT range. The cathode of the A thyristor-half faces the large flange side of the housing (the cathode side of a standard PCT element). The cathode connections to the B thyristor-half are made through the wall of the ceramic nearest the unflanged side (the anode side of the standard PCT element). Differently sized connectors to the A and B thyristor gate and cathode pairs prevent the false connection of the device during installation and maintenance. Fixed current collectors and specially machined molybdenum discs allow accurate and reliable centering of the wafer sandwich in the housing without the need for centering rings. Outlines of the 3.3 Surge Current Behaviour of a BCT In a classical thyristor the maximum allowable surge current depends on whether reverse or forward voltage is applied after the current transient. The most critical case is forward voltage. Evidently in a BCT, a reverse voltage VR for the A thyristor is simultaneously a forward voltage VD for the B thyristor (fig. 3.4). Yet it makes a difference if the reapplied voltage after a surge current pulse is positive (in forward direction) with respect to the thyristor which was formerly conducting (thyristor A for example, case 1) or positive with respect to its counterpart B which was formerly not conducting (case 2). In the situation corresponding to re-applied forward voltage for a classical thyristor (case 1), the surge current limit of a BCT is similar to the one of a classical thyristor of equal area. In the case often relevant for SVC applications, however, where a classical thyristor is exposed to reverse re-applied voltage only, i.e. case 2, a situation unique to the BCT appears, where the edge regions 1 and 2 close to the separation region are the most sensitive. The mask layout has been designed such that the separation region is strong enough to prevent failure in these sensitive regions. Separation region IT(A) B A VD(B) B A IT VD(A) (A formerly conducting) (a) (b) VD(B) VD(A) B side A side (formerly conducting) (c) Fig. 3.4: Currents and voltages after turn-off of the A thyristor. (a): circuit diagram, (b): separated into two thyristors, (c): schematic view of the wafer. The regions 1 and 2 are the most sensitive in respect to surge current (with re-applied "reverse" voltage) and the tq capability of a BCT. 3.4 Crosstalk and tq Again, the integration of the two thyristors on one wafer leads to a unique situation when the tq limit is approached in the application. The reason is again that the reverse voltage used to turn the conducting thyristor-half A off is a positive voltage for its 6 counterpart (fig. 3.5). The regions 1 and 2 as well as their connecting area would be the most sensitive locations. The photomask set of the BCT has been conceived with particular attention to maintaining the tq capability of two separated thyristors. Doc. No. 5SYA 2006-02 Feb. 99 IT(A) VD(B) VD(A) t VR(A) tH VR(B) tq Fig. 3.5: Typical current and voltage waveforms after turn-off of the A thyristor. A reverse voltage for the A thyristor-half is simultaneously a forward voltage for the B thyristor-half. The holding time tH has to be larger than or equal to the recovery time tq of the BCT. 3.5 Quality and Reliability 3.5.1 Quality Since a BCT is basically nothing more than two thyristors integrated on one wafer, most quality issues can be handled as for classical thyristors. The BCTspecific parameters are tested separately in addition to satisfy all quality requirements as described below in section 5. In particular, crosstalk tests are an essential part of the qualification procedure. 3.5.2 Reliability From the design point of view, load cycling is expected to induce different stresses and movements in the device housing than in a classical thyristor. In our experiments, however, no perceivable difference in load cycle capability has been found. In comparison with the classical thyristor, the BCT has no need for other high-voltage blocking junction termination measures. In particular, the separation region does not carry significant lateral voltage drops; it is even short-circuited by the metallisation on both wafer sides. Therefore, the voltage blocking reliability is by design as good as that of a classical thyristor. The full characterisation and approval procedure is elucidated in section 5. 4. BCT User's Guide As it was mentioned before, the BCT is a new way of monolithically integrating two high performance PCTs (Phase Control Thyristors) on the same silicon wafer in one housing. Consequently, the definitions and the characterising parameters of a BCT are practically almost the same as those of a PCT. Yet there are a few exceptions which will be explained in this section. The definitions and parameters not explained in this document are described in the ABB Semiconductors PCT data book. The data book also gives application information for PCTs which is applicable to BCTs as well. 7 4.1 BCT-Specific Features 4.1.1 Mechanical Design To reduce logistical problems for both manufacturer and customer, most mechanical parts are the same for the BCT and the PCT. This brings the advantage of having the outer dimensions and the Doc. No. 5SYA 2006-02 Feb. 99 clamping forces for the BCT the same as for the standard PCT range of ABB Semiconductors. This enables the user to have the same mechanical clamping design for both PCT as BCT, which gives a good cost optimisation potential in applications where both PCTs and BCTs are used. One major difference exists though, and that is that the BCT has two gate and two auxiliary cathode contacts. Connecting the gate wire intended for thyristor A to that of thyristor B and vice versa will in most applications lead to destruction of one or several components. To avoid this, the cathode contact on side A has a fast-on connector of size 6.3 x 0.8 mm, while the cathode contact on side B is a fast-on connector of size 4.8 x 0.8 mm. This feature makes the mounting procedure safe, since it is not possible to connect the wrong gate wire set on either side. Fig. 4.1: BCT outline showing the gate and the cathode. At the housing wall, different connectors are used for the A and B thyristor-halves to avoid incorrect connection of the gate wires. 4.1.2 Electrical Parameters As far as most electrical parameters are concerned, the BCT data is the same as for the standard PCT range. This enables the user, for example, to utilise the same gate driver units for both types of devices. The BCT design makes it necessary to define certain parameters in a different way to a standard PCT. The absence of a unique reverse direction makes the PCT differentiation between forward and reverse voltages obsolete. The BCT device has forward blocking voltage characteristics in both directions. The blocking voltage and current parameters necessary to specify a BCT are the following: VRM is the maximum repetitive voltage level that the BCT is able to block in either direction. The voltage is defined for half-sine voltage pulses of a line frequency of 50 or 60 Hz. Exceeding the specified maximum VRM will lead to uncontrolled triggering or thermal runaway which usually ends with device failure. 8 IRM specifies the maximum leakage current when VRM is applied. It is measured with 50 Hz half sine pulses at Tvjmax. A decrease in junction temperature will lead to a decreased leakage current. VSM is the maximum surge voltage level the BCT is able to block. VSM represents the BCT's ability to withstand non-repetitive voltage transients with a pulse width of 10 ms or less, which may be caused by overvoltage transients due to switching. Exceeding VSM can lead to uncontrolled triggering and to device destruction. In our documentation, VSM is not specified for devices with VRM < 4400 V, since for those devices VRM and VSM are equal over the whole temperature range. For devices with VSM > 4400 V, VSM and VRM are equal for junction temperatures up to 110 C. For temperatures below 110 C, it is possible to utilise values of VRM up to VSM. As an example, it is possible to use the 5STB 13N6500 at VRM = VSM = 6500 V at Tvj Doc. No. 5SYA 2006-02 Feb. 99 < 110 C, while VRM = 5600 V must not be exceeded at Tvj = 125 C. ISM specifies the maximum leakage current when VSM is applied. It is measured at Tvjmax with tp = 10 ms. Again, a decrease in junction temperature will lead to a decreased leakage current. For the definition of the parameters ITSM, Q, tq, VGD, IGD, (di/dt)crit, (dv/dt)crit and td in the data sheets, the abbreviations VD and VR are used. VD is a voltage in the forward direction of the thyristor-half that will be or just has been triggered, in the case of td, or just has conducted current, in the case of Q and tq. Analogously, VR is a voltage in the reverse direction of the thyristor-half that is active for the parameter described. The design and manufacturing technology of ABB Semiconductors makes it possible to produce BCTs with two thyristor functions with almost identical behaviour. For each electrical parameter, one value or one curve only is given in the data sheet. The value or curve given is valid for both thyristor functions in the BCT. One set of curves and data is sufficient for the application circuit design, and, from an electrical point of view, no particular care has to be taken in which direction the device is being mounted. 4.1.3 Thermal Parameters The thermal resistance data and the thermal impedance curve are given for one thyristor half with the condition that both thyristors are in operation as in an SVC or a soft starter. Due to radial heat spreading the thermal values for operation with only one thyristor half at the time, as example in a DC-drive, will be slightly reduced. Studies of this effect are on-going and it is foreseen that new revisions of the data sheets include two thermal resistance figures. One for both thyristor halves operating and one for only one thyristor half operating. 4.2 Application Examples The BCT has been developed as a complement to the standard PCT product range of ABB Semiconductors. The target was to reduce cost and thereby to increase the competitiveness of our customers in those areas where the common encapsulation of the two antiparallel thyristors yields advantages. In this paragraph, three application examples are given which show the advantage of using the BCT in comparison with a 9 standard PCT solution. One advantage common to all three examples is the increased reliability. The BCT is produced in the same manufacturing facility as our PCTs, and it uses the same basic parts, resulting in a product with the same high MTTF figure as each of our standard PCTs. Since one BCT replaces two PCTs, now, the MTTF for the whole assembly significantly improves. In addition, as can be seen in the application examples, the number of other (mechanical and electrical) parts is also reduced, so that a further increase in reliability for the whole equipment can be obtained. 4.2.1 Static VAr Compensation (SVC) For efficient power transmission, the reactive power consumed by asynchronous motors or arc furnaces, for example, has to be compensated, to keep the power factor on the transmission line close to unity. One of several means to accomplish this is Static VAr Compensation. SVC has the advantage over rotating compensators that it lacks moving parts. The components included in an SVC installation are capacitors, inductors and thyristor stacks. The thyristor stacks consist of a number of series-connected thyristors, which normally have additional components in parallel to them. These components serve to reduce the voltage stresses caused by the turn-off process of the thyristor and to share static and transient voltages equally between the thyristors. For the sharing of transient voltages as well as for the reduction of the turn-off over-voltage peak, a resistor and a capacitor in series are often used. The sharing of the static voltage is kept equal by placing additional resistors parallel to each thyristor. Since each stack of standard thyristors can only conduct current in one direction, two stacks have to be used in parallel for each phase of the equipment. This means that all mechanical parts needed, such as heat sinks, insulators and clamps as well as some of the electrical components have to be used for each current direction, as can be seen in figure 4.2. Using BCTs instead of PCTs, as in figure 4.2, only one stack per phase is needed, since the current can now be controlled in both directions. Depending on the choice of the system solution, the required number of electrical and mechanical components will be reduced by 10 - 30 %. This reduction has a significant impact on cost and foot print and enables the SVC manufacturer to substantially raise the competitiveness of his product. Doc. No. 5SYA 2006-02 Feb. 99 Fig. 4.2: Comparison between SVC thyristor stack assemblies with a conventional PCT solution on the left and a BCT solution on the right. For the stack itself, the BCT solution needs only 50 % of the mechanical and electrical parts that are used in the PCT solution. 4.2.2 Motor Drives To control the speed of electrical motors, an AC or DC drive is commonly used, since other means of regulating the speed have become too costly and consume too much energy. The main application areas for the BCT in drives equipment are in DC drives and in feeding sections for AC drives with return (regeneration) of energy to the power grid during breaking. Another application area is that of cycloconverters for large synchronous motors. The application example chosen below is a regenerative DC drive. The standard solution for a regenerative DC drive is the so-called (B6C)2 connection, which consists of two fully controlled rectifiers in anti-parallel connection. This is accomplished by using an assembly with 12 thyristors. An example of this is given in figure 4.3. 10 When BCTs are utilised, a (B6C)2 bridge is built with only 6 semiconductor components. Depending on the solution used, the (B6C)2 bridge then has either a reduced height or width. The use of the BCT in this application enables a more compact solution requiring less mechanical components like heat sinks and supports. The choice of a more compact solution again means a foot print reduction for a larger system, like a rolling mill line-up, by about 10 - 30 %. This is a major cost saving, since building electrical rooms is quite expensive. It can also enable high power drives equipment to be located in rooms with reduced height, as in a harbour crane, avoiding paralleling of low power bridges when more power is needed. This solution is drawn in figure 4.3. The user can not normally save on RC-circuit and fuse cost after substituting BCTs, since these components are already shared in the classical PCT solution. Doc. No. 5SYA 2006-02 Feb. 99 Fig. 4.3: Comparison between PCT and BCT assemblies for four-quadrant DC drives. The left assembly is using PCTs, and the right one is made of BCTs. The example shows the possibility of reducing height when using BCTs which enables high power DC drives to be installed in locations with height restrictions, like a harbour crane. of anti-parallel thyristors having one pair per phase. As can be seen in figure 4.4, these anti-parallel thyristors 4.2.3 Soft Starters can be directly replaced by a BCT. As for the DC drive, When starting an asynchronous machine which is this substitution leads to a reduced number of directly fed from a three-phase supply net, the machine mechanical parts like mounting clamps, and it enables and the feeding circuit will be heavily loaded by the a more compact solution. high starting currents. To reduce this stress, a soft starter is often used. This soft starter consists of pairs 11 Doc. No. 5SYA 2006-02 Feb. 99 Fig. 4.4: Comparison of three-phase soft starter assemblies using PCTs and BCTs. The left assembly is made of PCTs, and the right one is using BCTs. The BCT solution enables a reduction in the number of required mechanical parts and therefore in size. 4.2.4 Improvement potential in using the BCT BCT designs offer considerable volume and part counts reduction over conventional PCT ones. The table below summarises expected improvements by application and power level. Application Power level DC-drive DC-drive Soft starter Soft starter SVCB 800 kW 2000 kW 250 kW 450 kW 50 MVAr Anticipated average volume improvement (*) 30% 30% 25% 30% 35% Anticipated average parts count reduction (*) 30% 25% 20% 20& 35% (*) Compared to conventional PCT solutions. 12 Doc. No. 5SYA 2006-02 Feb. 99 5. Production Testing and Product Qualification The testing of a Bi-Directional Control Thyristor (BCT) is based on the same testing sequence and philosophy as the one for the well proven PCT. In combination with the extensive qualification of the newly developed devices this assures that the same high quality and reliability are achieved. The routine production testing as well as the qualification test procedures are described below. Sections 4.6 and 4.7 of the 1996 edition of the PCT data book of ABB Semiconductors describe related documents and standards as well as product traceability and failure analysis. These sections are also applicable to the BCT. The basic electrical parameter testing is performed at the wafer level (before and after electron irradiation) and after packaging (standard or customised final test procedure), exactly as for PCTs. The main difference lies in the fact that the BCT has two thyristor-halves (A and B), so that the device has to be measured twice with respect to many parameters. Examples are: QA: recovery charge of thyristor-half A, QB: recovery charge of thyristor-half B, VRMA: maximum forward repetitive voltage for thyristor-half A, VRMB: maximum forward repetitive voltage for thyristor-half B. 5.1 General Production Testing The table below shows the parameters that are 100% routine tested in production. Group A Testing: 100% Routine Production Testing Parameter VRMA VRMB VSMA VSMB dv/dt critA dv/dt critB QA QB VTA VTB IGTA VGTA IGTB VGTB tqA Temperature 25/125C 25/125C 125C 125C 125C 125C 125C 125C 125C 125C 25C 25C 25C 25C 125C Type of test 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% Protocols test report test report test report test report test report test report test report test report test report test report test report test report test report test report test report tqB 125C 100% test report ITSMA ITSMB 125C 125C 100% 100% test report test report ITSM with re-applied voltage and tq are the most common requirements for measurements of adapted standard products. Other parameters not listed in the table may equally be agreed upon. The test reports are the computer print-outs of the final test. Since dv/dt, Q and tq are Group B Testing: Lot Control Tests (Scheduled Product Audits) In order to assure and to monitor the long-term voltage stability, Group B testing may be integrated for final screening. Eight 13 Remark for 5200 and 6500V devices for 5200 and 6500V devices tested on wafer level tested on wafer level tested on wafer level tested on wafer level for adapted standards, tested on wafer level for adapted standards, tested on wafer level for adapted standards for adapted standards measured at wafer level, these values are included in the test report where this is required by the customer. The test sequence and the lay-out of the test report for adapted standard products are defined in the spec review process as described in the PCT data book. devices per selected lot undergo a voltage stability test for 24 h at VDC A,B = 2/3 VRM (VDC A = DC forward voltage at thyristor-half A, VRM = maximum forward repetitive voltage). A typical pass criterion is that the drift of the leakage current be 0.2 mA. Doc. No. 5SYA 2006-02 Feb. 99 Examination or Test Reference Documents Inspection Requirements Sub-group Test Category IEC Ref. MIL-STD750C Ref. Conditions n c B2 Endurance: DC blocking 1048 24 h at TC = 80C...Tvjmax VA, VB = 2/3 VRM 8 0 Notes 1 mF) is charged up to 2500 V and is then discharged (iTmax = 2000 A) through an inductor (L = 1.3 mH) after the BCT is triggered. When, for example, thyristor-half A is turned off, a reverse voltage develops across it. This voltage is simultaneously a forward voltage for thyristor-half B (figure 3.5). The peak amplitude depends on the capacitance and the resistance of the snubber used. With our set-up, it is somewhat below VSM. 5.2 Qualification Approval Tests and Qualification Maintenance Tests For the BCT qualification procedure it has been particularly necessary to introduce an additional characterisation test assuring that there is no disturbing interaction between the two separated antiparallel thyristor-halves located on the wafer. This socalled "crosstalk test" is performed as follows. For the BCT crosstalk test, a circuit as shown in fig. 5.1 is utilised. A capacitor (C = D2 RV=68 L=1.3mH V2 Rd VDC D1 A B Rs C=1mF V1 Cs Rsh=1m Fig. 5.1: Test circuit for the crosstalk measurement The new designs undergo rigorous qualification testing (Group D testing), whereby the data sheet values are verified and the reliability ascertained: this is an essential part of our development model. The BCTs are qualified and released for production and sale 14 when the defined tests have been passed. Most of these tests are also part of the bi-annual reliability monitoring tests (Group C testing). The table below summarises ABB Semiconductors' commitment to reliability. Doc. No. 5SYA 2006-02 Feb. 99 Examination or Test SubTest Category group D1a Characteristics inspection D1b Complementary characteristics inspection Verification of maximum ratings Endurance: Storage at high temperature D1c D2 D3 Reference Documents IEC MIL 750C JIS C 7021 Internal Ref. Conditions Parameters and quantities see applicable test specification Internal Ref. Parameters and quantities see applicable test specification Internal Ref. Parameters and quantities see applicable test specification 68-2-2 1000 h at Tstg max 10 1031.4 7021 B-10 68-2-1 Aa 7021 B-12 D4 Endurance: Storage at low temperature Endurance: AC blocking D5 Endurance: DC blocking D6 Endurance: DC blocking D7 Endurance: Thermal cycling load (Thermal fatigue) D8 Endurance: Operating life D9 Rapid change of temperature D10a Shock 7021 A-3 68-2-27 Ea 2016.2 7021 A-7 D10b Vibration 68-2-6 Fc Shock 2056 7021 A-10 68-2-27 Ea 500 h at Tstg min 747-6 V 1000 h at Tvj max Sine wave 50 Hz VD(R) = 0.7...0.8 VD(R)RM 1048 1000 h at 90C...Tvj max 7021 B-20 VD(R) = 0.7...0.8 VD(R)RM Internal Ref. 1000 h at T = 25C C VD(R) = VD(R)RM (or de-rated voltage) 747-6 IV, 4 T = 80C ... 100C vj 1037.1 5 . 1 10 cycles (Traction) 7021 B-18 5 . 0.2 10 cycles (Industry) 6 Internal Ref. 1.10 on/off cycles with ITGQM and VD max, specific drive and snubber circuits 68-2-14 Nc 0C to 100C, 15 cycles, liquid 1056.2 to liquid D11b Impact Shock (Bump) 68-2-29 Eb D11c Vibration 68-2-6 Fc D12 Salt mist 2056 68-2-11 Ka Components in stack a = 50 gn, 11 ms, 3 shocks per direction Components in stack 10 to 500 Hz, d 0.75 mm, a 10 gn, 10 cycles per axis, 113 min Components in transport box a = 50 gn, 11 ms, 3 shocks per direction Components in transport box a = 40 gn, 6 ms, 1000 shocks per direction Components in transport box 10 to 500 Hz, d 0.35 mm, a 5 gn, 10 cycles per axis, 120 min 35C, 5% NaCl, 7 days D13 Robustness of terminations 1046.2 68-2-21 Tension, 40 N, 10 s D11a Inspection Requirements n c Notes 2016.2 0 Note 1 10 0 Note 1 8 0 Note 1 8 0 Note 1 30 Note 4 12 0 Note 1 10 0 Note 4 10 0 Note 1 4 0 Note 2 4 0 Note 2 4 0 Note 2 4 0 Note 2 4 0 Note 2 4 0 Note 3 4 0 2036.3 A 7021 A-11 15 Doc. No. 5SYA 2006-02 Feb. 99 Notes: The device must meet requirements listed under note 1. 1.) Failure criteria for Diodes: 3.) Failure criteria for all Puck devices: No significant IRRM (Tvj max) < 1.1 USL, VFM < 1.1 USL corrosion. Failure criteria for Thyristors: 4.) Not applicable for BCT-devices. IRRM, IDRM (Tvjmax) < 1.1 USL, VGT (25C) < 1.1 USL, VTM (Tvj max) < 1.1 USL 2.) Failure criteria for all Puck devices: Integrity of package materials, wafers, sealing, lead connections 6. Customer Technology and Application Support For most applications the explicit data sheets of ABB Semiconductors give sufficient information to design a powerful and competitive application circuit. In some cases, however, for customer projects with revised or new circuit concepts, it may be that a somewhat different set of thyristor parameters is desirable. This includes the trade-off between conduction and switching losses, but it often goes beyond that. As is also described above and in the ABB Semiconductors PCT data book, a so-called "adapted standard" product can be produced in a manner analogous to the standard PCT thyristors. During development of new circuit technologies and concepts, it often happens that very specific device data and relationships are needed which cannot be ABB Semiconductors AG Fabrikstrasse 3 CH-5600 Lenzburg, Switzerland Telephone +41 (0)62 888 6419 Fax +41 (0)62 888 6306 Internet www.abbsem.com extracted from the data sheets. Moreover, the customer may need support and advice about how to most efficiently utilise and control the semiconductor device in his new circuit. ABB Semiconductors has a wealth of experience to offer in this field as well. This includes areas such as power loss calculations, temperature calculations under transient conditions, or gate driving. Very powerful and versatile tools are available to perform application-oriented simulations of device behaviour as well as to perform special application-oriented tests on our semiconductor devices. If you need information or support in one of the above areas, please contact our sales organisation or your nearest ABB Semiconductors agent.